1 // SPDX-License-Identifier: GPL-2.0
2 /*
3  * Copyright (C) 2018 Marvell
4  *
5  * Authors:
6  *   Evan Wang <xswang@marvell.com>
7  *   Miquèl Raynal <miquel.raynal@bootlin.com>
8  *   Pali Rohár <pali@kernel.org>
9  *   Marek Behún <kabel@kernel.org>
10  *
11  * Structure inspired from phy-mvebu-cp110-comphy.c written by Antoine Tenart.
12  * Comphy code from ARM Trusted Firmware ported by Pali Rohár <pali@kernel.org>
13  * and Marek Behún <kabel@kernel.org>.
14  */
15 
16 #include <linux/bitfield.h>
17 #include <linux/clk.h>
18 #include <linux/io.h>
19 #include <linux/iopoll.h>
20 #include <linux/mfd/syscon.h>
21 #include <linux/module.h>
22 #include <linux/of.h>
23 #include <linux/phy.h>
24 #include <linux/phy/phy.h>
25 #include <linux/platform_device.h>
26 #include <linux/spinlock.h>
27 
28 #define PLL_SET_DELAY_US		600
29 #define COMPHY_PLL_SLEEP		1000
30 #define COMPHY_PLL_TIMEOUT		150000
31 
32 /* Comphy lane2 indirect access register offset */
33 #define COMPHY_LANE2_INDIR_ADDR		0x0
34 #define COMPHY_LANE2_INDIR_DATA		0x4
35 
36 /* SATA and USB3 PHY offset compared to SATA PHY */
37 #define COMPHY_LANE2_REGS_BASE		0x200
38 
39 /*
40  * When accessing common PHY lane registers directly, we need to shift by 1,
41  * since the registers are 16-bit.
42  */
43 #define COMPHY_LANE_REG_DIRECT(reg)	(((reg) & 0x7FF) << 1)
44 
45 /* COMPHY registers */
46 #define COMPHY_POWER_PLL_CTRL		0x01
47 #define PU_IVREF_BIT			BIT(15)
48 #define PU_PLL_BIT			BIT(14)
49 #define PU_RX_BIT			BIT(13)
50 #define PU_TX_BIT			BIT(12)
51 #define PU_TX_INTP_BIT			BIT(11)
52 #define PU_DFE_BIT			BIT(10)
53 #define RESET_DTL_RX_BIT		BIT(9)
54 #define PLL_LOCK_BIT			BIT(8)
55 #define REF_FREF_SEL_MASK		GENMASK(4, 0)
56 #define REF_FREF_SEL_SERDES_25MHZ	FIELD_PREP(REF_FREF_SEL_MASK, 0x1)
57 #define REF_FREF_SEL_SERDES_40MHZ	FIELD_PREP(REF_FREF_SEL_MASK, 0x3)
58 #define REF_FREF_SEL_SERDES_50MHZ	FIELD_PREP(REF_FREF_SEL_MASK, 0x4)
59 #define REF_FREF_SEL_PCIE_USB3_25MHZ	FIELD_PREP(REF_FREF_SEL_MASK, 0x2)
60 #define REF_FREF_SEL_PCIE_USB3_40MHZ	FIELD_PREP(REF_FREF_SEL_MASK, 0x3)
61 #define COMPHY_MODE_MASK		GENMASK(7, 5)
62 #define COMPHY_MODE_SATA		FIELD_PREP(COMPHY_MODE_MASK, 0x0)
63 #define COMPHY_MODE_PCIE		FIELD_PREP(COMPHY_MODE_MASK, 0x3)
64 #define COMPHY_MODE_SERDES		FIELD_PREP(COMPHY_MODE_MASK, 0x4)
65 #define COMPHY_MODE_USB3		FIELD_PREP(COMPHY_MODE_MASK, 0x5)
66 
67 #define COMPHY_KVCO_CAL_CTRL		0x02
68 #define USE_MAX_PLL_RATE_BIT		BIT(12)
69 #define SPEED_PLL_MASK			GENMASK(7, 2)
70 #define SPEED_PLL_VALUE_16		FIELD_PREP(SPEED_PLL_MASK, 0x10)
71 
72 #define COMPHY_DIG_LOOPBACK_EN		0x23
73 #define SEL_DATA_WIDTH_MASK		GENMASK(11, 10)
74 #define DATA_WIDTH_10BIT		FIELD_PREP(SEL_DATA_WIDTH_MASK, 0x0)
75 #define DATA_WIDTH_20BIT		FIELD_PREP(SEL_DATA_WIDTH_MASK, 0x1)
76 #define DATA_WIDTH_40BIT		FIELD_PREP(SEL_DATA_WIDTH_MASK, 0x2)
77 #define PLL_READY_TX_BIT		BIT(4)
78 
79 #define COMPHY_SYNC_PATTERN		0x24
80 #define TXD_INVERT_BIT			BIT(10)
81 #define RXD_INVERT_BIT			BIT(11)
82 
83 #define COMPHY_SYNC_MASK_GEN		0x25
84 #define PHY_GEN_MAX_MASK		GENMASK(11, 10)
85 #define PHY_GEN_MAX_USB3_5G		FIELD_PREP(PHY_GEN_MAX_MASK, 0x1)
86 
87 #define COMPHY_ISOLATION_CTRL		0x26
88 #define PHY_ISOLATE_MODE		BIT(15)
89 
90 #define COMPHY_GEN2_SET2		0x3e
91 #define GS2_TX_SSC_AMP_MASK		GENMASK(15, 9)
92 #define GS2_TX_SSC_AMP_4128		FIELD_PREP(GS2_TX_SSC_AMP_MASK, 0x20)
93 #define GS2_VREG_RXTX_MAS_ISET_MASK	GENMASK(8, 7)
94 #define GS2_VREG_RXTX_MAS_ISET_60U	FIELD_PREP(GS2_VREG_RXTX_MAS_ISET_MASK,\
95 						   0x0)
96 #define GS2_VREG_RXTX_MAS_ISET_80U	FIELD_PREP(GS2_VREG_RXTX_MAS_ISET_MASK,\
97 						   0x1)
98 #define GS2_VREG_RXTX_MAS_ISET_100U	FIELD_PREP(GS2_VREG_RXTX_MAS_ISET_MASK,\
99 						   0x2)
100 #define GS2_VREG_RXTX_MAS_ISET_120U	FIELD_PREP(GS2_VREG_RXTX_MAS_ISET_MASK,\
101 						   0x3)
102 #define GS2_RSVD_6_0_MASK		GENMASK(6, 0)
103 
104 #define COMPHY_GEN3_SET2		0x3f
105 
106 #define COMPHY_IDLE_SYNC_EN		0x48
107 #define IDLE_SYNC_EN			BIT(12)
108 
109 #define COMPHY_MISC_CTRL0		0x4F
110 #define CLK100M_125M_EN			BIT(4)
111 #define TXDCLK_2X_SEL			BIT(6)
112 #define CLK500M_EN			BIT(7)
113 #define PHY_REF_CLK_SEL			BIT(10)
114 
115 #define COMPHY_SFT_RESET		0x52
116 #define SFT_RST				BIT(9)
117 #define SFT_RST_NO_REG			BIT(10)
118 
119 #define COMPHY_MISC_CTRL1		0x73
120 #define SEL_BITS_PCIE_FORCE		BIT(15)
121 
122 #define COMPHY_GEN2_SET3		0x112
123 #define GS3_FFE_CAP_SEL_MASK		GENMASK(3, 0)
124 #define GS3_FFE_CAP_SEL_VALUE		FIELD_PREP(GS3_FFE_CAP_SEL_MASK, 0xF)
125 
126 /* PIPE registers */
127 #define COMPHY_PIPE_LANE_CFG0		0x180
128 #define PRD_TXDEEMPH0_MASK		BIT(0)
129 #define PRD_TXMARGIN_MASK		GENMASK(3, 1)
130 #define PRD_TXSWING_MASK		BIT(4)
131 #define CFG_TX_ALIGN_POS_MASK		GENMASK(8, 5)
132 
133 #define COMPHY_PIPE_LANE_CFG1		0x181
134 #define PRD_TXDEEMPH1_MASK		BIT(15)
135 #define USE_MAX_PLL_RATE_EN		BIT(9)
136 #define TX_DET_RX_MODE			BIT(6)
137 #define GEN2_TX_DATA_DLY_MASK		GENMASK(4, 3)
138 #define GEN2_TX_DATA_DLY_DEFT		FIELD_PREP(GEN2_TX_DATA_DLY_MASK, 2)
139 #define TX_ELEC_IDLE_MODE_EN		BIT(0)
140 
141 #define COMPHY_PIPE_LANE_STAT1		0x183
142 #define TXDCLK_PCLK_EN			BIT(0)
143 
144 #define COMPHY_PIPE_LANE_CFG4		0x188
145 #define SPREAD_SPECTRUM_CLK_EN		BIT(7)
146 
147 #define COMPHY_PIPE_RST_CLK_CTRL	0x1C1
148 #define PIPE_SOFT_RESET			BIT(0)
149 #define PIPE_REG_RESET			BIT(1)
150 #define MODE_CORE_CLK_FREQ_SEL		BIT(9)
151 #define MODE_PIPE_WIDTH_32		BIT(3)
152 #define MODE_REFDIV_MASK		GENMASK(5, 4)
153 #define MODE_REFDIV_BY_4		FIELD_PREP(MODE_REFDIV_MASK, 0x2)
154 
155 #define COMPHY_PIPE_TEST_MODE_CTRL	0x1C2
156 #define MODE_MARGIN_OVERRIDE		BIT(2)
157 
158 #define COMPHY_PIPE_CLK_SRC_LO		0x1C3
159 #define MODE_CLK_SRC			BIT(0)
160 #define BUNDLE_PERIOD_SEL		BIT(1)
161 #define BUNDLE_PERIOD_SCALE_MASK	GENMASK(3, 2)
162 #define BUNDLE_SAMPLE_CTRL		BIT(4)
163 #define PLL_READY_DLY_MASK		GENMASK(7, 5)
164 #define CFG_SEL_20B			BIT(15)
165 
166 #define COMPHY_PIPE_PWR_MGM_TIM1	0x1D0
167 #define CFG_PM_OSCCLK_WAIT_MASK		GENMASK(15, 12)
168 #define CFG_PM_RXDEN_WAIT_MASK		GENMASK(11, 8)
169 #define CFG_PM_RXDEN_WAIT_1_UNIT	FIELD_PREP(CFG_PM_RXDEN_WAIT_MASK, 0x1)
170 #define CFG_PM_RXDLOZ_WAIT_MASK		GENMASK(7, 0)
171 #define CFG_PM_RXDLOZ_WAIT_7_UNIT	FIELD_PREP(CFG_PM_RXDLOZ_WAIT_MASK, 0x7)
172 #define CFG_PM_RXDLOZ_WAIT_12_UNIT	FIELD_PREP(CFG_PM_RXDLOZ_WAIT_MASK, 0xC)
173 
174 /*
175  * This register is not from PHY lane register space. It only exists in the
176  * indirect register space, before the actual PHY lane 2 registers. So the
177  * offset is absolute, not relative to COMPHY_LANE2_REGS_BASE.
178  * It is used only for SATA PHY initialization.
179  */
180 #define COMPHY_RESERVED_REG		0x0E
181 #define PHYCTRL_FRM_PIN_BIT		BIT(13)
182 
183 /* South Bridge PHY Configuration Registers */
184 #define COMPHY_PHY_REG(lane, reg)	(((1 - (lane)) * 0x28) + ((reg) & 0x3f))
185 
186 /*
187  * lane0: USB3/GbE1 PHY Configuration 1
188  * lane1: PCIe/GbE0 PHY Configuration 1
189  * (used only by SGMII code)
190  */
191 #define COMPHY_PHY_CFG1			0x0
192 #define PIN_PU_IVREF_BIT		BIT(1)
193 #define PIN_RESET_CORE_BIT		BIT(11)
194 #define PIN_RESET_COMPHY_BIT		BIT(12)
195 #define PIN_PU_PLL_BIT			BIT(16)
196 #define PIN_PU_RX_BIT			BIT(17)
197 #define PIN_PU_TX_BIT			BIT(18)
198 #define PIN_TX_IDLE_BIT			BIT(19)
199 #define GEN_RX_SEL_MASK			GENMASK(25, 22)
200 #define GEN_RX_SEL_VALUE(val)		FIELD_PREP(GEN_RX_SEL_MASK, (val))
201 #define GEN_TX_SEL_MASK			GENMASK(29, 26)
202 #define GEN_TX_SEL_VALUE(val)		FIELD_PREP(GEN_TX_SEL_MASK, (val))
203 #define SERDES_SPEED_1_25_G		0x6
204 #define SERDES_SPEED_3_125_G		0x8
205 #define PHY_RX_INIT_BIT			BIT(30)
206 
207 /*
208  * lane0: USB3/GbE1 PHY Status 1
209  * lane1: PCIe/GbE0 PHY Status 1
210  * (used only by SGMII code)
211  */
212 #define COMPHY_PHY_STAT1		0x18
213 #define PHY_RX_INIT_DONE_BIT		BIT(0)
214 #define PHY_PLL_READY_RX_BIT		BIT(2)
215 #define PHY_PLL_READY_TX_BIT		BIT(3)
216 
217 /* PHY Selector */
218 #define COMPHY_SELECTOR_PHY_REG			0xFC
219 /* bit0: 0: Lane1 is GbE0; 1: Lane1 is PCIe */
220 #define COMPHY_SELECTOR_PCIE_GBE0_SEL_BIT	BIT(0)
221 /* bit4: 0: Lane0 is GbE1; 1: Lane0 is USB3 */
222 #define COMPHY_SELECTOR_USB3_GBE1_SEL_BIT	BIT(4)
223 /* bit8: 0: Lane0 is USB3 instead of GbE1, Lane2 is SATA; 1: Lane2 is USB3 */
224 #define COMPHY_SELECTOR_USB3_PHY_SEL_BIT	BIT(8)
225 
226 struct mvebu_a3700_comphy_conf {
227 	unsigned int lane;
228 	enum phy_mode mode;
229 	int submode;
230 };
231 
232 #define MVEBU_A3700_COMPHY_CONF(_lane, _mode, _smode)			\
233 	{								\
234 		.lane = _lane,						\
235 		.mode = _mode,						\
236 		.submode = _smode,					\
237 	}
238 
239 #define MVEBU_A3700_COMPHY_CONF_GEN(_lane, _mode) \
240 	MVEBU_A3700_COMPHY_CONF(_lane, _mode, PHY_INTERFACE_MODE_NA)
241 
242 #define MVEBU_A3700_COMPHY_CONF_ETH(_lane, _smode) \
243 	MVEBU_A3700_COMPHY_CONF(_lane, PHY_MODE_ETHERNET, _smode)
244 
245 static const struct mvebu_a3700_comphy_conf mvebu_a3700_comphy_modes[] = {
246 	/* lane 0 */
247 	MVEBU_A3700_COMPHY_CONF_GEN(0, PHY_MODE_USB_HOST_SS),
248 	MVEBU_A3700_COMPHY_CONF_ETH(0, PHY_INTERFACE_MODE_SGMII),
249 	MVEBU_A3700_COMPHY_CONF_ETH(0, PHY_INTERFACE_MODE_1000BASEX),
250 	MVEBU_A3700_COMPHY_CONF_ETH(0, PHY_INTERFACE_MODE_2500BASEX),
251 	/* lane 1 */
252 	MVEBU_A3700_COMPHY_CONF_GEN(1, PHY_MODE_PCIE),
253 	MVEBU_A3700_COMPHY_CONF_ETH(1, PHY_INTERFACE_MODE_SGMII),
254 	MVEBU_A3700_COMPHY_CONF_ETH(1, PHY_INTERFACE_MODE_1000BASEX),
255 	MVEBU_A3700_COMPHY_CONF_ETH(1, PHY_INTERFACE_MODE_2500BASEX),
256 	/* lane 2 */
257 	MVEBU_A3700_COMPHY_CONF_GEN(2, PHY_MODE_SATA),
258 	MVEBU_A3700_COMPHY_CONF_GEN(2, PHY_MODE_USB_HOST_SS),
259 };
260 
261 struct mvebu_a3700_comphy_priv {
262 	void __iomem *comphy_regs;
263 	void __iomem *lane0_phy_regs; /* USB3 and GbE1 */
264 	void __iomem *lane1_phy_regs; /* PCIe and GbE0 */
265 	void __iomem *lane2_phy_indirect; /* SATA and USB3 */
266 	spinlock_t lock; /* for PHY selector access */
267 	bool xtal_is_40m;
268 };
269 
270 struct mvebu_a3700_comphy_lane {
271 	struct mvebu_a3700_comphy_priv *priv;
272 	struct device *dev;
273 	unsigned int id;
274 	enum phy_mode mode;
275 	int submode;
276 	bool invert_tx;
277 	bool invert_rx;
278 };
279 
280 struct gbe_phy_init_data_fix {
281 	u16 addr;
282 	u16 value;
283 };
284 
285 /* Changes to 40M1G25 mode data required for running 40M3G125 init mode */
286 static struct gbe_phy_init_data_fix gbe_phy_init_fix[] = {
287 	{ 0x005, 0x07CC }, { 0x015, 0x0000 }, { 0x01B, 0x0000 },
288 	{ 0x01D, 0x0000 }, { 0x01E, 0x0000 }, { 0x01F, 0x0000 },
289 	{ 0x020, 0x0000 }, { 0x021, 0x0030 }, { 0x026, 0x0888 },
290 	{ 0x04D, 0x0152 }, { 0x04F, 0xA020 }, { 0x050, 0x07CC },
291 	{ 0x053, 0xE9CA }, { 0x055, 0xBD97 }, { 0x071, 0x3015 },
292 	{ 0x076, 0x03AA }, { 0x07C, 0x0FDF }, { 0x0C2, 0x3030 },
293 	{ 0x0C3, 0x8000 }, { 0x0E2, 0x5550 }, { 0x0E3, 0x12A4 },
294 	{ 0x0E4, 0x7D00 }, { 0x0E6, 0x0C83 }, { 0x101, 0xFCC0 },
295 	{ 0x104, 0x0C10 }
296 };
297 
298 /* 40M1G25 mode init data */
299 static u16 gbe_phy_init[512] = {
300 	/* 0       1       2       3       4       5       6       7 */
301 	/*-----------------------------------------------------------*/
302 	/* 8       9       A       B       C       D       E       F */
303 	0x3110, 0xFD83, 0x6430, 0x412F, 0x82C0, 0x06FA, 0x4500, 0x6D26,	/* 00 */
304 	0xAFC0, 0x8000, 0xC000, 0x0000, 0x2000, 0x49CC, 0x0BC9, 0x2A52,	/* 08 */
305 	0x0BD2, 0x0CDE, 0x13D2, 0x0CE8, 0x1149, 0x10E0, 0x0000, 0x0000,	/* 10 */
306 	0x0000, 0x0000, 0x0000, 0x0001, 0x0000, 0x4134, 0x0D2D, 0xFFFF,	/* 18 */
307 	0xFFE0, 0x4030, 0x1016, 0x0030, 0x0000, 0x0800, 0x0866, 0x0000,	/* 20 */
308 	0x0000, 0x0000, 0xFFFF, 0xFFFF, 0xFFFF, 0xFFFF, 0xFFFF, 0xFFFF,	/* 28 */
309 	0xFFFF, 0xFFFF, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/* 30 */
310 	0x0000, 0x0000, 0x000F, 0x6A62, 0x1988, 0x3100, 0x3100, 0x3100,	/* 38 */
311 	0x3100, 0xA708, 0x2430, 0x0830, 0x1030, 0x4610, 0xFF00, 0xFF00,	/* 40 */
312 	0x0060, 0x1000, 0x0400, 0x0040, 0x00F0, 0x0155, 0x1100, 0xA02A,	/* 48 */
313 	0x06FA, 0x0080, 0xB008, 0xE3ED, 0x5002, 0xB592, 0x7A80, 0x0001,	/* 50 */
314 	0x020A, 0x8820, 0x6014, 0x8054, 0xACAA, 0xFC88, 0x2A02, 0x45CF,	/* 58 */
315 	0x000F, 0x1817, 0x2860, 0x064F, 0x0000, 0x0204, 0x1800, 0x6000,	/* 60 */
316 	0x810F, 0x4F23, 0x4000, 0x4498, 0x0850, 0x0000, 0x000E, 0x1002,	/* 68 */
317 	0x9D3A, 0x3009, 0xD066, 0x0491, 0x0001, 0x6AB0, 0x0399, 0x3780,	/* 70 */
318 	0x0040, 0x5AC0, 0x4A80, 0x0000, 0x01DF, 0x0000, 0x0007, 0x0000,	/* 78 */
319 	0x2D54, 0x00A1, 0x4000, 0x0100, 0xA20A, 0x0000, 0x0000, 0x0000,	/* 80 */
320 	0x0000, 0x0000, 0x0000, 0x7400, 0x0E81, 0x1000, 0x1242, 0x0210,	/* 88 */
321 	0x80DF, 0x0F1F, 0x2F3F, 0x4F5F, 0x6F7F, 0x0F1F, 0x2F3F, 0x4F5F,	/* 90 */
322 	0x6F7F, 0x4BAD, 0x0000, 0x0000, 0x0800, 0x0000, 0x2400, 0xB651,	/* 98 */
323 	0xC9E0, 0x4247, 0x0A24, 0x0000, 0xAF19, 0x1004, 0x0000, 0x0000,	/* A0 */
324 	0x0000, 0x0013, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/* A8 */
325 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/* B0 */
326 	0x0000, 0x0000, 0x0000, 0x0060, 0x0000, 0x0000, 0x0000, 0x0000,	/* B8 */
327 	0x0000, 0x0000, 0x3010, 0xFA00, 0x0000, 0x0000, 0x0000, 0x0003,	/* C0 */
328 	0x1618, 0x8200, 0x8000, 0x0400, 0x050F, 0x0000, 0x0000, 0x0000,	/* C8 */
329 	0x4C93, 0x0000, 0x1000, 0x1120, 0x0010, 0x1242, 0x1242, 0x1E00,	/* D0 */
330 	0x0000, 0x0000, 0x0000, 0x00F8, 0x0000, 0x0041, 0x0800, 0x0000,	/* D8 */
331 	0x82A0, 0x572E, 0x2490, 0x14A9, 0x4E00, 0x0000, 0x0803, 0x0541,	/* E0 */
332 	0x0C15, 0x0000, 0x0000, 0x0400, 0x2626, 0x0000, 0x0000, 0x4200,	/* E8 */
333 	0x0000, 0xAA55, 0x1020, 0x0000, 0x0000, 0x5010, 0x0000, 0x0000,	/* F0 */
334 	0x0000, 0x0000, 0x5000, 0x0000, 0x0000, 0x0000, 0x02F2, 0x0000,	/* F8 */
335 	0x101F, 0xFDC0, 0x4000, 0x8010, 0x0110, 0x0006, 0x0000, 0x0000,	/*100 */
336 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*108 */
337 	0x04CF, 0x0000, 0x04CF, 0x0000, 0x04CF, 0x0000, 0x04C6, 0x0000,	/*110 */
338 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*118 */
339 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*120 */
340 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*128 */
341 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*130 */
342 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*138 */
343 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*140 */
344 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*148 */
345 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*150 */
346 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*158 */
347 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*160 */
348 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*168 */
349 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*170 */
350 	0x0000, 0x0000, 0x0000, 0x00F0, 0x08A2, 0x3112, 0x0A14, 0x0000,	/*178 */
351 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*180 */
352 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*188 */
353 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*190 */
354 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*198 */
355 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*1A0 */
356 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*1A8 */
357 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*1B0 */
358 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*1B8 */
359 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*1C0 */
360 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*1C8 */
361 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*1D0 */
362 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*1D8 */
363 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*1E0 */
364 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*1E8 */
365 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,	/*1F0 */
366 	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000	/*1F8 */
367 };
368 
369 static inline void comphy_reg_set(void __iomem *addr, u32 data, u32 mask)
370 {
371 	u32 val;
372 
373 	val = readl(addr);
374 	val = (val & ~mask) | (data & mask);
375 	writel(val, addr);
376 }
377 
378 static inline void comphy_reg_set16(void __iomem *addr, u16 data, u16 mask)
379 {
380 	u16 val;
381 
382 	val = readw(addr);
383 	val = (val & ~mask) | (data & mask);
384 	writew(val, addr);
385 }
386 
387 /* Used for accessing lane 2 registers (SATA/USB3 PHY) */
388 static void comphy_set_indirect(struct mvebu_a3700_comphy_priv *priv,
389 				u32 offset, u16 data, u16 mask)
390 {
391 	writel(offset,
392 	       priv->lane2_phy_indirect + COMPHY_LANE2_INDIR_ADDR);
393 	comphy_reg_set(priv->lane2_phy_indirect + COMPHY_LANE2_INDIR_DATA,
394 		       data, mask);
395 }
396 
397 static void comphy_lane_reg_set(struct mvebu_a3700_comphy_lane *lane,
398 				u16 reg, u16 data, u16 mask)
399 {
400 	if (lane->id == 2) {
401 		/* lane 2 PHY registers are accessed indirectly */
402 		comphy_set_indirect(lane->priv,
403 				    reg + COMPHY_LANE2_REGS_BASE,
404 				    data, mask);
405 	} else {
406 		void __iomem *base = lane->id == 1 ?
407 				     lane->priv->lane1_phy_regs :
408 				     lane->priv->lane0_phy_regs;
409 
410 		comphy_reg_set16(base + COMPHY_LANE_REG_DIRECT(reg),
411 				 data, mask);
412 	}
413 }
414 
415 static int comphy_lane_reg_poll(struct mvebu_a3700_comphy_lane *lane,
416 				u16 reg, u16 bits,
417 				ulong sleep_us, ulong timeout_us)
418 {
419 	int ret;
420 
421 	if (lane->id == 2) {
422 		u32 data;
423 
424 		/* lane 2 PHY registers are accessed indirectly */
425 		writel(reg + COMPHY_LANE2_REGS_BASE,
426 		       lane->priv->lane2_phy_indirect +
427 		       COMPHY_LANE2_INDIR_ADDR);
428 
429 		ret = readl_poll_timeout(lane->priv->lane2_phy_indirect +
430 					 COMPHY_LANE2_INDIR_DATA,
431 					 data, (data & bits) == bits,
432 					 sleep_us, timeout_us);
433 	} else {
434 		void __iomem *base = lane->id == 1 ?
435 				     lane->priv->lane1_phy_regs :
436 				     lane->priv->lane0_phy_regs;
437 		u16 data;
438 
439 		ret = readw_poll_timeout(base + COMPHY_LANE_REG_DIRECT(reg),
440 					 data, (data & bits) == bits,
441 					 sleep_us, timeout_us);
442 	}
443 
444 	return ret;
445 }
446 
447 static void comphy_periph_reg_set(struct mvebu_a3700_comphy_lane *lane,
448 				  u8 reg, u32 data, u32 mask)
449 {
450 	comphy_reg_set(lane->priv->comphy_regs + COMPHY_PHY_REG(lane->id, reg),
451 		       data, mask);
452 }
453 
454 static int comphy_periph_reg_poll(struct mvebu_a3700_comphy_lane *lane,
455 				  u8 reg, u32 bits,
456 				  ulong sleep_us, ulong timeout_us)
457 {
458 	u32 data;
459 
460 	return readl_poll_timeout(lane->priv->comphy_regs +
461 				  COMPHY_PHY_REG(lane->id, reg),
462 				  data, (data & bits) == bits,
463 				  sleep_us, timeout_us);
464 }
465 
466 /* PHY selector configures with corresponding modes */
467 static int
468 mvebu_a3700_comphy_set_phy_selector(struct mvebu_a3700_comphy_lane *lane)
469 {
470 	u32 old, new, clr = 0, set = 0;
471 	unsigned long flags;
472 
473 	switch (lane->mode) {
474 	case PHY_MODE_SATA:
475 		/* SATA must be in Lane2 */
476 		if (lane->id == 2)
477 			clr = COMPHY_SELECTOR_USB3_PHY_SEL_BIT;
478 		else
479 			goto error;
480 		break;
481 
482 	case PHY_MODE_ETHERNET:
483 		if (lane->id == 0)
484 			clr = COMPHY_SELECTOR_USB3_GBE1_SEL_BIT;
485 		else if (lane->id == 1)
486 			clr = COMPHY_SELECTOR_PCIE_GBE0_SEL_BIT;
487 		else
488 			goto error;
489 		break;
490 
491 	case PHY_MODE_USB_HOST_SS:
492 		if (lane->id == 2)
493 			set = COMPHY_SELECTOR_USB3_PHY_SEL_BIT;
494 		else if (lane->id == 0)
495 			set = COMPHY_SELECTOR_USB3_GBE1_SEL_BIT;
496 		else
497 			goto error;
498 		break;
499 
500 	case PHY_MODE_PCIE:
501 		/* PCIE must be in Lane1 */
502 		if (lane->id == 1)
503 			set = COMPHY_SELECTOR_PCIE_GBE0_SEL_BIT;
504 		else
505 			goto error;
506 		break;
507 
508 	default:
509 		goto error;
510 	}
511 
512 	spin_lock_irqsave(&lane->priv->lock, flags);
513 
514 	old = readl(lane->priv->comphy_regs + COMPHY_SELECTOR_PHY_REG);
515 	new = (old & ~clr) | set;
516 	writel(new, lane->priv->comphy_regs + COMPHY_SELECTOR_PHY_REG);
517 
518 	spin_unlock_irqrestore(&lane->priv->lock, flags);
519 
520 	dev_dbg(lane->dev,
521 		"COMPHY[%d] mode[%d] changed PHY selector 0x%08x -> 0x%08x\n",
522 		lane->id, lane->mode, old, new);
523 
524 	return 0;
525 error:
526 	dev_err(lane->dev, "COMPHY[%d] mode[%d] is invalid\n", lane->id,
527 		lane->mode);
528 	return -EINVAL;
529 }
530 
531 static int
532 mvebu_a3700_comphy_sata_power_on(struct mvebu_a3700_comphy_lane *lane)
533 {
534 	u32 mask, data, ref_clk;
535 	int ret;
536 
537 	/* Configure phy selector for SATA */
538 	ret = mvebu_a3700_comphy_set_phy_selector(lane);
539 	if (ret)
540 		return ret;
541 
542 	/* Clear phy isolation mode to make it work in normal mode */
543 	comphy_lane_reg_set(lane, COMPHY_ISOLATION_CTRL,
544 			    0x0, PHY_ISOLATE_MODE);
545 
546 	/* 0. Check the Polarity invert bits */
547 	data = 0x0;
548 	if (lane->invert_tx)
549 		data |= TXD_INVERT_BIT;
550 	if (lane->invert_rx)
551 		data |= RXD_INVERT_BIT;
552 	mask = TXD_INVERT_BIT | RXD_INVERT_BIT;
553 	comphy_lane_reg_set(lane, COMPHY_SYNC_PATTERN, data, mask);
554 
555 	/* 1. Select 40-bit data width */
556 	comphy_lane_reg_set(lane, COMPHY_DIG_LOOPBACK_EN,
557 			    DATA_WIDTH_40BIT, SEL_DATA_WIDTH_MASK);
558 
559 	/* 2. Select reference clock(25M) and PHY mode (SATA) */
560 	if (lane->priv->xtal_is_40m)
561 		ref_clk = REF_FREF_SEL_SERDES_40MHZ;
562 	else
563 		ref_clk = REF_FREF_SEL_SERDES_25MHZ;
564 
565 	data = ref_clk | COMPHY_MODE_SATA;
566 	mask = REF_FREF_SEL_MASK | COMPHY_MODE_MASK;
567 	comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL, data, mask);
568 
569 	/* 3. Use maximum PLL rate (no power save) */
570 	comphy_lane_reg_set(lane, COMPHY_KVCO_CAL_CTRL,
571 			    USE_MAX_PLL_RATE_BIT, USE_MAX_PLL_RATE_BIT);
572 
573 	/* 4. Reset reserved bit */
574 	comphy_set_indirect(lane->priv, COMPHY_RESERVED_REG,
575 			    0x0, PHYCTRL_FRM_PIN_BIT);
576 
577 	/* 5. Set vendor-specific configuration (It is done in sata driver) */
578 	/* XXX: in U-Boot below sequence was executed in this place, in Linux
579 	 * not.  Now it is done only in U-Boot before this comphy
580 	 * initialization - tests shows that it works ok, but in case of any
581 	 * future problem it is left for reference.
582 	 *   reg_set(MVEBU_REGS_BASE + 0xe00a0, 0, 0xffffffff);
583 	 *   reg_set(MVEBU_REGS_BASE + 0xe00a4, BIT(6), BIT(6));
584 	 */
585 
586 	/* Wait for > 55 us to allow PLL be enabled */
587 	udelay(PLL_SET_DELAY_US);
588 
589 	/* Polling status */
590 	ret = comphy_lane_reg_poll(lane, COMPHY_DIG_LOOPBACK_EN,
591 				   PLL_READY_TX_BIT, COMPHY_PLL_SLEEP,
592 				   COMPHY_PLL_TIMEOUT);
593 	if (ret)
594 		dev_err(lane->dev, "Failed to lock SATA PLL\n");
595 
596 	return ret;
597 }
598 
599 static void comphy_gbe_phy_init(struct mvebu_a3700_comphy_lane *lane,
600 				bool is_1gbps)
601 {
602 	int addr, fix_idx;
603 	u16 val;
604 
605 	fix_idx = 0;
606 	for (addr = 0; addr < ARRAY_SIZE(gbe_phy_init); addr++) {
607 		/*
608 		 * All PHY register values are defined in full for 3.125Gbps
609 		 * SERDES speed. The values required for 1.25 Gbps are almost
610 		 * the same and only few registers should be "fixed" in
611 		 * comparison to 3.125 Gbps values. These register values are
612 		 * stored in "gbe_phy_init_fix" array.
613 		 */
614 		if (!is_1gbps &&
615 		    fix_idx < ARRAY_SIZE(gbe_phy_init_fix) &&
616 		    gbe_phy_init_fix[fix_idx].addr == addr) {
617 			/* Use new value */
618 			val = gbe_phy_init_fix[fix_idx].value;
619 			fix_idx++;
620 		} else {
621 			val = gbe_phy_init[addr];
622 		}
623 
624 		comphy_lane_reg_set(lane, addr, val, 0xFFFF);
625 	}
626 }
627 
628 static int
629 mvebu_a3700_comphy_ethernet_power_on(struct mvebu_a3700_comphy_lane *lane)
630 {
631 	u32 mask, data, speed_sel;
632 	int ret;
633 
634 	/* Set selector */
635 	ret = mvebu_a3700_comphy_set_phy_selector(lane);
636 	if (ret)
637 		return ret;
638 
639 	/*
640 	 * 1. Reset PHY by setting PHY input port PIN_RESET=1.
641 	 * 2. Set PHY input port PIN_TX_IDLE=1, PIN_PU_IVREF=1 to keep
642 	 *    PHY TXP/TXN output to idle state during PHY initialization
643 	 * 3. Set PHY input port PIN_PU_PLL=0, PIN_PU_RX=0, PIN_PU_TX=0.
644 	 */
645 	data = PIN_PU_IVREF_BIT | PIN_TX_IDLE_BIT | PIN_RESET_COMPHY_BIT;
646 	mask = data | PIN_RESET_CORE_BIT | PIN_PU_PLL_BIT | PIN_PU_RX_BIT |
647 	       PIN_PU_TX_BIT | PHY_RX_INIT_BIT;
648 	comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, data, mask);
649 
650 	/* 4. Release reset to the PHY by setting PIN_RESET=0. */
651 	data = 0x0;
652 	mask = PIN_RESET_COMPHY_BIT;
653 	comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, data, mask);
654 
655 	/*
656 	 * 5. Set PIN_PHY_GEN_TX[3:0] and PIN_PHY_GEN_RX[3:0] to decide COMPHY
657 	 * bit rate
658 	 */
659 	switch (lane->submode) {
660 	case PHY_INTERFACE_MODE_SGMII:
661 	case PHY_INTERFACE_MODE_1000BASEX:
662 		/* SGMII 1G, SerDes speed 1.25G */
663 		speed_sel = SERDES_SPEED_1_25_G;
664 		break;
665 	case PHY_INTERFACE_MODE_2500BASEX:
666 		/* 2500Base-X, SerDes speed 3.125G */
667 		speed_sel = SERDES_SPEED_3_125_G;
668 		break;
669 	default:
670 		/* Other rates are not supported */
671 		dev_err(lane->dev,
672 			"unsupported phy speed %d on comphy lane%d\n",
673 			lane->submode, lane->id);
674 		return -EINVAL;
675 	}
676 	data = GEN_RX_SEL_VALUE(speed_sel) | GEN_TX_SEL_VALUE(speed_sel);
677 	mask = GEN_RX_SEL_MASK | GEN_TX_SEL_MASK;
678 	comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, data, mask);
679 
680 	/*
681 	 * 6. Wait 10mS for bandgap and reference clocks to stabilize; then
682 	 * start SW programming.
683 	 */
684 	mdelay(10);
685 
686 	/* 7. Program COMPHY register PHY_MODE */
687 	data = COMPHY_MODE_SERDES;
688 	mask = COMPHY_MODE_MASK;
689 	comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL, data, mask);
690 
691 	/*
692 	 * 8. Set COMPHY register REFCLK_SEL to select the correct REFCLK
693 	 * source
694 	 */
695 	data = 0x0;
696 	mask = PHY_REF_CLK_SEL;
697 	comphy_lane_reg_set(lane, COMPHY_MISC_CTRL0, data, mask);
698 
699 	/*
700 	 * 9. Set correct reference clock frequency in COMPHY register
701 	 * REF_FREF_SEL.
702 	 */
703 	if (lane->priv->xtal_is_40m)
704 		data = REF_FREF_SEL_SERDES_50MHZ;
705 	else
706 		data = REF_FREF_SEL_SERDES_25MHZ;
707 
708 	mask = REF_FREF_SEL_MASK;
709 	comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL, data, mask);
710 
711 	/*
712 	 * 10. Program COMPHY register PHY_GEN_MAX[1:0]
713 	 * This step is mentioned in the flow received from verification team.
714 	 * However the PHY_GEN_MAX value is only meaningful for other interfaces
715 	 * (not SERDES). For instance, it selects SATA speed 1.5/3/6 Gbps or
716 	 * PCIe speed 2.5/5 Gbps
717 	 */
718 
719 	/*
720 	 * 11. Program COMPHY register SEL_BITS to set correct parallel data
721 	 * bus width
722 	 */
723 	data = DATA_WIDTH_10BIT;
724 	mask = SEL_DATA_WIDTH_MASK;
725 	comphy_lane_reg_set(lane, COMPHY_DIG_LOOPBACK_EN, data, mask);
726 
727 	/*
728 	 * 12. As long as DFE function needs to be enabled in any mode,
729 	 * COMPHY register DFE_UPDATE_EN[5:0] shall be programmed to 0x3F
730 	 * for real chip during COMPHY power on.
731 	 * The value of the DFE_UPDATE_EN already is 0x3F, because it is the
732 	 * default value after reset of the PHY.
733 	 */
734 
735 	/*
736 	 * 13. Program COMPHY GEN registers.
737 	 * These registers should be programmed based on the lab testing result
738 	 * to achieve optimal performance. Please contact the CEA group to get
739 	 * the related GEN table during real chip bring-up. We only required to
740 	 * run though the entire registers programming flow defined by
741 	 * "comphy_gbe_phy_init" when the REF clock is 40 MHz. For REF clock
742 	 * 25 MHz the default values stored in PHY registers are OK.
743 	 */
744 	dev_dbg(lane->dev, "Running C-DPI phy init %s mode\n",
745 		lane->submode == PHY_INTERFACE_MODE_2500BASEX ? "2G5" : "1G");
746 	if (lane->priv->xtal_is_40m)
747 		comphy_gbe_phy_init(lane,
748 				    lane->submode != PHY_INTERFACE_MODE_2500BASEX);
749 
750 	/*
751 	 * 14. Check the PHY Polarity invert bit
752 	 */
753 	data = 0x0;
754 	if (lane->invert_tx)
755 		data |= TXD_INVERT_BIT;
756 	if (lane->invert_rx)
757 		data |= RXD_INVERT_BIT;
758 	mask = TXD_INVERT_BIT | RXD_INVERT_BIT;
759 	comphy_lane_reg_set(lane, COMPHY_SYNC_PATTERN, data, mask);
760 
761 	/*
762 	 * 15. Set PHY input ports PIN_PU_PLL, PIN_PU_TX and PIN_PU_RX to 1 to
763 	 * start PHY power up sequence. All the PHY register programming should
764 	 * be done before PIN_PU_PLL=1. There should be no register programming
765 	 * for normal PHY operation from this point.
766 	 */
767 	data = PIN_PU_PLL_BIT | PIN_PU_RX_BIT | PIN_PU_TX_BIT;
768 	mask = data;
769 	comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, data, mask);
770 
771 	/*
772 	 * 16. Wait for PHY power up sequence to finish by checking output ports
773 	 * PIN_PLL_READY_TX=1 and PIN_PLL_READY_RX=1.
774 	 */
775 	ret = comphy_periph_reg_poll(lane, COMPHY_PHY_STAT1,
776 				     PHY_PLL_READY_TX_BIT |
777 				     PHY_PLL_READY_RX_BIT,
778 				     COMPHY_PLL_SLEEP, COMPHY_PLL_TIMEOUT);
779 	if (ret) {
780 		dev_err(lane->dev, "Failed to lock PLL for SERDES PHY %d\n",
781 			lane->id);
782 		return ret;
783 	}
784 
785 	/*
786 	 * 17. Set COMPHY input port PIN_TX_IDLE=0
787 	 */
788 	comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, 0x0, PIN_TX_IDLE_BIT);
789 
790 	/*
791 	 * 18. After valid data appear on PIN_RXDATA bus, set PIN_RX_INIT=1. To
792 	 * start RX initialization. PIN_RX_INIT_DONE will be cleared to 0 by the
793 	 * PHY After RX initialization is done, PIN_RX_INIT_DONE will be set to
794 	 * 1 by COMPHY Set PIN_RX_INIT=0 after PIN_RX_INIT_DONE= 1. Please
795 	 * refer to RX initialization part for details.
796 	 */
797 	comphy_periph_reg_set(lane, COMPHY_PHY_CFG1,
798 			      PHY_RX_INIT_BIT, PHY_RX_INIT_BIT);
799 
800 	ret = comphy_periph_reg_poll(lane, COMPHY_PHY_STAT1,
801 				     PHY_PLL_READY_TX_BIT |
802 				     PHY_PLL_READY_RX_BIT,
803 				     COMPHY_PLL_SLEEP, COMPHY_PLL_TIMEOUT);
804 	if (ret) {
805 		dev_err(lane->dev, "Failed to lock PLL for SERDES PHY %d\n",
806 			lane->id);
807 		return ret;
808 	}
809 
810 	ret = comphy_periph_reg_poll(lane, COMPHY_PHY_STAT1,
811 				     PHY_RX_INIT_DONE_BIT,
812 				     COMPHY_PLL_SLEEP, COMPHY_PLL_TIMEOUT);
813 	if (ret)
814 		dev_err(lane->dev, "Failed to init RX of SERDES PHY %d\n",
815 			lane->id);
816 
817 	return ret;
818 }
819 
820 static int
821 mvebu_a3700_comphy_usb3_power_on(struct mvebu_a3700_comphy_lane *lane)
822 {
823 	u32 mask, data, cfg, ref_clk;
824 	int ret;
825 
826 	/* Set phy seclector */
827 	ret = mvebu_a3700_comphy_set_phy_selector(lane);
828 	if (ret)
829 		return ret;
830 
831 	/* COMPHY register reset (cleared automatically) */
832 	comphy_lane_reg_set(lane, COMPHY_SFT_RESET, SFT_RST, SFT_RST);
833 
834 	/*
835 	 * 0. Set PHY OTG Control(0x5d034), bit 4, Power up OTG module The
836 	 * register belong to UTMI module, so it is set in UTMI phy driver.
837 	 */
838 
839 	/*
840 	 * 1. Set PRD_TXDEEMPH (3.5db de-emph)
841 	 */
842 	data = PRD_TXDEEMPH0_MASK;
843 	mask = PRD_TXDEEMPH0_MASK | PRD_TXMARGIN_MASK | PRD_TXSWING_MASK |
844 	       CFG_TX_ALIGN_POS_MASK;
845 	comphy_lane_reg_set(lane, COMPHY_PIPE_LANE_CFG0, data, mask);
846 
847 	/*
848 	 * 2. Set BIT0: enable transmitter in high impedance mode
849 	 *    Set BIT[3:4]: delay 2 clock cycles for HiZ off latency
850 	 *    Set BIT6: Tx detect Rx at HiZ mode
851 	 *    Unset BIT15: set to 0 to set USB3 De-emphasize level to -3.5db
852 	 *            together with bit 0 of COMPHY_PIPE_LANE_CFG0 register
853 	 */
854 	data = TX_DET_RX_MODE | GEN2_TX_DATA_DLY_DEFT | TX_ELEC_IDLE_MODE_EN;
855 	mask = PRD_TXDEEMPH1_MASK | TX_DET_RX_MODE | GEN2_TX_DATA_DLY_MASK |
856 	       TX_ELEC_IDLE_MODE_EN;
857 	comphy_lane_reg_set(lane, COMPHY_PIPE_LANE_CFG1, data, mask);
858 
859 	/*
860 	 * 3. Set Spread Spectrum Clock Enabled
861 	 */
862 	comphy_lane_reg_set(lane, COMPHY_PIPE_LANE_CFG4,
863 			    SPREAD_SPECTRUM_CLK_EN, SPREAD_SPECTRUM_CLK_EN);
864 
865 	/*
866 	 * 4. Set Override Margining Controls From the MAC:
867 	 *    Use margining signals from lane configuration
868 	 */
869 	comphy_lane_reg_set(lane, COMPHY_PIPE_TEST_MODE_CTRL,
870 			    MODE_MARGIN_OVERRIDE, 0xFFFF);
871 
872 	/*
873 	 * 5. Set Lane-to-Lane Bundle Clock Sampling Period = per PCLK cycles
874 	 *    set Mode Clock Source = PCLK is generated from REFCLK
875 	 */
876 	data = 0x0;
877 	mask = MODE_CLK_SRC | BUNDLE_PERIOD_SEL | BUNDLE_PERIOD_SCALE_MASK |
878 	       BUNDLE_SAMPLE_CTRL | PLL_READY_DLY_MASK;
879 	comphy_lane_reg_set(lane, COMPHY_PIPE_CLK_SRC_LO, data, mask);
880 
881 	/*
882 	 * 6. Set G2 Spread Spectrum Clock Amplitude at 4K
883 	 */
884 	comphy_lane_reg_set(lane, COMPHY_GEN2_SET2,
885 			    GS2_TX_SSC_AMP_4128, GS2_TX_SSC_AMP_MASK);
886 
887 	/*
888 	 * 7. Unset G3 Spread Spectrum Clock Amplitude
889 	 *    set G3 TX and RX Register Master Current Select
890 	 */
891 	data = GS2_VREG_RXTX_MAS_ISET_60U;
892 	mask = GS2_TX_SSC_AMP_MASK | GS2_VREG_RXTX_MAS_ISET_MASK |
893 	       GS2_RSVD_6_0_MASK;
894 	comphy_lane_reg_set(lane, COMPHY_GEN3_SET2, data, mask);
895 
896 	/*
897 	 * 8. Check crystal jumper setting and program the Power and PLL Control
898 	 * accordingly Change RX wait
899 	 */
900 	if (lane->priv->xtal_is_40m) {
901 		ref_clk = REF_FREF_SEL_PCIE_USB3_40MHZ;
902 		cfg = CFG_PM_RXDLOZ_WAIT_12_UNIT;
903 	} else {
904 		ref_clk = REF_FREF_SEL_PCIE_USB3_25MHZ;
905 		cfg = CFG_PM_RXDLOZ_WAIT_7_UNIT;
906 	}
907 
908 	data = PU_IVREF_BIT | PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT |
909 	       PU_TX_INTP_BIT | PU_DFE_BIT | COMPHY_MODE_USB3 | ref_clk;
910 	mask = PU_IVREF_BIT | PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT |
911 	       PU_TX_INTP_BIT | PU_DFE_BIT | PLL_LOCK_BIT | COMPHY_MODE_MASK |
912 	       REF_FREF_SEL_MASK;
913 	comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL, data, mask);
914 
915 	data = CFG_PM_RXDEN_WAIT_1_UNIT | cfg;
916 	mask = CFG_PM_OSCCLK_WAIT_MASK | CFG_PM_RXDEN_WAIT_MASK |
917 	       CFG_PM_RXDLOZ_WAIT_MASK;
918 	comphy_lane_reg_set(lane, COMPHY_PIPE_PWR_MGM_TIM1, data, mask);
919 
920 	/*
921 	 * 9. Enable idle sync
922 	 */
923 	comphy_lane_reg_set(lane, COMPHY_IDLE_SYNC_EN,
924 			    IDLE_SYNC_EN, IDLE_SYNC_EN);
925 
926 	/*
927 	 * 10. Enable the output of 500M clock
928 	 */
929 	comphy_lane_reg_set(lane, COMPHY_MISC_CTRL0, CLK500M_EN, CLK500M_EN);
930 
931 	/*
932 	 * 11. Set 20-bit data width
933 	 */
934 	comphy_lane_reg_set(lane, COMPHY_DIG_LOOPBACK_EN,
935 			    DATA_WIDTH_20BIT, 0xFFFF);
936 
937 	/*
938 	 * 12. Override Speed_PLL value and use MAC PLL
939 	 */
940 	data = SPEED_PLL_VALUE_16 | USE_MAX_PLL_RATE_BIT;
941 	mask = 0xFFFF;
942 	comphy_lane_reg_set(lane, COMPHY_KVCO_CAL_CTRL, data, mask);
943 
944 	/*
945 	 * 13. Check the Polarity invert bit
946 	 */
947 	data = 0x0;
948 	if (lane->invert_tx)
949 		data |= TXD_INVERT_BIT;
950 	if (lane->invert_rx)
951 		data |= RXD_INVERT_BIT;
952 	mask = TXD_INVERT_BIT | RXD_INVERT_BIT;
953 	comphy_lane_reg_set(lane, COMPHY_SYNC_PATTERN, data, mask);
954 
955 	/*
956 	 * 14. Set max speed generation to USB3.0 5Gbps
957 	 */
958 	comphy_lane_reg_set(lane, COMPHY_SYNC_MASK_GEN,
959 			    PHY_GEN_MAX_USB3_5G, PHY_GEN_MAX_MASK);
960 
961 	/*
962 	 * 15. Set capacitor value for FFE gain peaking to 0xF
963 	 */
964 	comphy_lane_reg_set(lane, COMPHY_GEN2_SET3,
965 			    GS3_FFE_CAP_SEL_VALUE, GS3_FFE_CAP_SEL_MASK);
966 
967 	/*
968 	 * 16. Release SW reset
969 	 */
970 	data = MODE_CORE_CLK_FREQ_SEL | MODE_PIPE_WIDTH_32 | MODE_REFDIV_BY_4;
971 	mask = 0xFFFF;
972 	comphy_lane_reg_set(lane, COMPHY_PIPE_RST_CLK_CTRL, data, mask);
973 
974 	/* Wait for > 55 us to allow PCLK be enabled */
975 	udelay(PLL_SET_DELAY_US);
976 
977 	ret = comphy_lane_reg_poll(lane, COMPHY_PIPE_LANE_STAT1, TXDCLK_PCLK_EN,
978 				   COMPHY_PLL_SLEEP, COMPHY_PLL_TIMEOUT);
979 	if (ret)
980 		dev_err(lane->dev, "Failed to lock USB3 PLL\n");
981 
982 	return ret;
983 }
984 
985 static int
986 mvebu_a3700_comphy_pcie_power_on(struct mvebu_a3700_comphy_lane *lane)
987 {
988 	u32 mask, data, ref_clk;
989 	int ret;
990 
991 	/* Configure phy selector for PCIe */
992 	ret = mvebu_a3700_comphy_set_phy_selector(lane);
993 	if (ret)
994 		return ret;
995 
996 	/* 1. Enable max PLL. */
997 	comphy_lane_reg_set(lane, COMPHY_PIPE_LANE_CFG1,
998 			    USE_MAX_PLL_RATE_EN, USE_MAX_PLL_RATE_EN);
999 
1000 	/* 2. Select 20 bit SERDES interface. */
1001 	comphy_lane_reg_set(lane, COMPHY_PIPE_CLK_SRC_LO,
1002 			    CFG_SEL_20B, CFG_SEL_20B);
1003 
1004 	/* 3. Force to use reg setting for PCIe mode */
1005 	comphy_lane_reg_set(lane, COMPHY_MISC_CTRL1,
1006 			    SEL_BITS_PCIE_FORCE, SEL_BITS_PCIE_FORCE);
1007 
1008 	/* 4. Change RX wait */
1009 	data = CFG_PM_RXDEN_WAIT_1_UNIT | CFG_PM_RXDLOZ_WAIT_12_UNIT;
1010 	mask = CFG_PM_OSCCLK_WAIT_MASK | CFG_PM_RXDEN_WAIT_MASK |
1011 	       CFG_PM_RXDLOZ_WAIT_MASK;
1012 	comphy_lane_reg_set(lane, COMPHY_PIPE_PWR_MGM_TIM1, data, mask);
1013 
1014 	/* 5. Enable idle sync */
1015 	comphy_lane_reg_set(lane, COMPHY_IDLE_SYNC_EN,
1016 			    IDLE_SYNC_EN, IDLE_SYNC_EN);
1017 
1018 	/* 6. Enable the output of 100M/125M/500M clock */
1019 	data = CLK500M_EN | TXDCLK_2X_SEL | CLK100M_125M_EN;
1020 	mask = data;
1021 	comphy_lane_reg_set(lane, COMPHY_MISC_CTRL0, data, mask);
1022 
1023 	/*
1024 	 * 7. Enable TX, PCIE global register, 0xd0074814, it is done in
1025 	 * PCI-E driver
1026 	 */
1027 
1028 	/*
1029 	 * 8. Check crystal jumper setting and program the Power and PLL
1030 	 * Control accordingly
1031 	 */
1032 
1033 	if (lane->priv->xtal_is_40m)
1034 		ref_clk = REF_FREF_SEL_PCIE_USB3_40MHZ;
1035 	else
1036 		ref_clk = REF_FREF_SEL_PCIE_USB3_25MHZ;
1037 
1038 	data = PU_IVREF_BIT | PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT |
1039 	       PU_TX_INTP_BIT | PU_DFE_BIT | COMPHY_MODE_PCIE | ref_clk;
1040 	mask = 0xFFFF;
1041 	comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL, data, mask);
1042 
1043 	/* 9. Override Speed_PLL value and use MAC PLL */
1044 	comphy_lane_reg_set(lane, COMPHY_KVCO_CAL_CTRL,
1045 			    SPEED_PLL_VALUE_16 | USE_MAX_PLL_RATE_BIT,
1046 			    0xFFFF);
1047 
1048 	/* 10. Check the Polarity invert bit */
1049 	data = 0x0;
1050 	if (lane->invert_tx)
1051 		data |= TXD_INVERT_BIT;
1052 	if (lane->invert_rx)
1053 		data |= RXD_INVERT_BIT;
1054 	mask = TXD_INVERT_BIT | RXD_INVERT_BIT;
1055 	comphy_lane_reg_set(lane, COMPHY_SYNC_PATTERN, data, mask);
1056 
1057 	/* 11. Release SW reset */
1058 	data = MODE_CORE_CLK_FREQ_SEL | MODE_PIPE_WIDTH_32;
1059 	mask = data | PIPE_SOFT_RESET | MODE_REFDIV_MASK;
1060 	comphy_lane_reg_set(lane, COMPHY_PIPE_RST_CLK_CTRL, data, mask);
1061 
1062 	/* Wait for > 55 us to allow PCLK be enabled */
1063 	udelay(PLL_SET_DELAY_US);
1064 
1065 	ret = comphy_lane_reg_poll(lane, COMPHY_PIPE_LANE_STAT1, TXDCLK_PCLK_EN,
1066 				   COMPHY_PLL_SLEEP, COMPHY_PLL_TIMEOUT);
1067 	if (ret)
1068 		dev_err(lane->dev, "Failed to lock PCIE PLL\n");
1069 
1070 	return ret;
1071 }
1072 
1073 static void
1074 mvebu_a3700_comphy_sata_power_off(struct mvebu_a3700_comphy_lane *lane)
1075 {
1076 	/* Set phy isolation mode */
1077 	comphy_lane_reg_set(lane, COMPHY_ISOLATION_CTRL,
1078 			    PHY_ISOLATE_MODE, PHY_ISOLATE_MODE);
1079 
1080 	/* Power off PLL, Tx, Rx */
1081 	comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL,
1082 			    0x0, PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT);
1083 }
1084 
1085 static void
1086 mvebu_a3700_comphy_ethernet_power_off(struct mvebu_a3700_comphy_lane *lane)
1087 {
1088 	u32 mask, data;
1089 
1090 	data = PIN_RESET_CORE_BIT | PIN_RESET_COMPHY_BIT | PIN_PU_IVREF_BIT |
1091 	       PHY_RX_INIT_BIT;
1092 	mask = data;
1093 	comphy_periph_reg_set(lane, COMPHY_PHY_CFG1, data, mask);
1094 }
1095 
1096 static void
1097 mvebu_a3700_comphy_pcie_power_off(struct mvebu_a3700_comphy_lane *lane)
1098 {
1099 	/* Power off PLL, Tx, Rx */
1100 	comphy_lane_reg_set(lane, COMPHY_POWER_PLL_CTRL,
1101 			    0x0, PU_PLL_BIT | PU_RX_BIT | PU_TX_BIT);
1102 }
1103 
1104 static void mvebu_a3700_comphy_usb3_power_off(struct mvebu_a3700_comphy_lane *lane)
1105 {
1106 	/*
1107 	 * The USB3 MAC sets the USB3 PHY to low state, so we do not
1108 	 * need to power off USB3 PHY again.
1109 	 */
1110 }
1111 
1112 static bool mvebu_a3700_comphy_check_mode(int lane,
1113 					  enum phy_mode mode,
1114 					  int submode)
1115 {
1116 	int i, n = ARRAY_SIZE(mvebu_a3700_comphy_modes);
1117 
1118 	/* Unused PHY mux value is 0x0 */
1119 	if (mode == PHY_MODE_INVALID)
1120 		return false;
1121 
1122 	for (i = 0; i < n; i++) {
1123 		if (mvebu_a3700_comphy_modes[i].lane == lane &&
1124 		    mvebu_a3700_comphy_modes[i].mode == mode &&
1125 		    mvebu_a3700_comphy_modes[i].submode == submode)
1126 			break;
1127 	}
1128 
1129 	if (i == n)
1130 		return false;
1131 
1132 	return true;
1133 }
1134 
1135 static int mvebu_a3700_comphy_set_mode(struct phy *phy, enum phy_mode mode,
1136 				       int submode)
1137 {
1138 	struct mvebu_a3700_comphy_lane *lane = phy_get_drvdata(phy);
1139 
1140 	if (!mvebu_a3700_comphy_check_mode(lane->id, mode, submode)) {
1141 		dev_err(lane->dev, "invalid COMPHY mode\n");
1142 		return -EINVAL;
1143 	}
1144 
1145 	/* Mode cannot be changed while the PHY is powered on */
1146 	if (phy->power_count &&
1147 	    (lane->mode != mode || lane->submode != submode))
1148 		return -EBUSY;
1149 
1150 	/* Just remember the mode, ->power_on() will do the real setup */
1151 	lane->mode = mode;
1152 	lane->submode = submode;
1153 
1154 	return 0;
1155 }
1156 
1157 static int mvebu_a3700_comphy_power_on(struct phy *phy)
1158 {
1159 	struct mvebu_a3700_comphy_lane *lane = phy_get_drvdata(phy);
1160 
1161 	if (!mvebu_a3700_comphy_check_mode(lane->id, lane->mode,
1162 					   lane->submode)) {
1163 		dev_err(lane->dev, "invalid COMPHY mode\n");
1164 		return -EINVAL;
1165 	}
1166 
1167 	switch (lane->mode) {
1168 	case PHY_MODE_USB_HOST_SS:
1169 		dev_dbg(lane->dev, "set lane %d to USB3 host mode\n", lane->id);
1170 		return mvebu_a3700_comphy_usb3_power_on(lane);
1171 	case PHY_MODE_SATA:
1172 		dev_dbg(lane->dev, "set lane %d to SATA mode\n", lane->id);
1173 		return mvebu_a3700_comphy_sata_power_on(lane);
1174 	case PHY_MODE_ETHERNET:
1175 		dev_dbg(lane->dev, "set lane %d to Ethernet mode\n", lane->id);
1176 		return mvebu_a3700_comphy_ethernet_power_on(lane);
1177 	case PHY_MODE_PCIE:
1178 		dev_dbg(lane->dev, "set lane %d to PCIe mode\n", lane->id);
1179 		return mvebu_a3700_comphy_pcie_power_on(lane);
1180 	default:
1181 		dev_err(lane->dev, "unsupported PHY mode (%d)\n", lane->mode);
1182 		return -EOPNOTSUPP;
1183 	}
1184 }
1185 
1186 static int mvebu_a3700_comphy_power_off(struct phy *phy)
1187 {
1188 	struct mvebu_a3700_comphy_lane *lane = phy_get_drvdata(phy);
1189 
1190 	switch (lane->id) {
1191 	case 0:
1192 		mvebu_a3700_comphy_usb3_power_off(lane);
1193 		mvebu_a3700_comphy_ethernet_power_off(lane);
1194 		return 0;
1195 	case 1:
1196 		mvebu_a3700_comphy_pcie_power_off(lane);
1197 		mvebu_a3700_comphy_ethernet_power_off(lane);
1198 		return 0;
1199 	case 2:
1200 		mvebu_a3700_comphy_usb3_power_off(lane);
1201 		mvebu_a3700_comphy_sata_power_off(lane);
1202 		return 0;
1203 	default:
1204 		dev_err(lane->dev, "invalid COMPHY mode\n");
1205 		return -EINVAL;
1206 	}
1207 }
1208 
1209 static const struct phy_ops mvebu_a3700_comphy_ops = {
1210 	.power_on	= mvebu_a3700_comphy_power_on,
1211 	.power_off	= mvebu_a3700_comphy_power_off,
1212 	.set_mode	= mvebu_a3700_comphy_set_mode,
1213 	.owner		= THIS_MODULE,
1214 };
1215 
1216 static struct phy *mvebu_a3700_comphy_xlate(struct device *dev,
1217 					    struct of_phandle_args *args)
1218 {
1219 	struct mvebu_a3700_comphy_lane *lane;
1220 	unsigned int port;
1221 	struct phy *phy;
1222 
1223 	phy = of_phy_simple_xlate(dev, args);
1224 	if (IS_ERR(phy))
1225 		return phy;
1226 
1227 	lane = phy_get_drvdata(phy);
1228 
1229 	port = args->args[0];
1230 	if (port != 0 && (port != 1 || lane->id != 0)) {
1231 		dev_err(lane->dev, "invalid port number %u\n", port);
1232 		return ERR_PTR(-EINVAL);
1233 	}
1234 
1235 	lane->invert_tx = args->args[1] & BIT(0);
1236 	lane->invert_rx = args->args[1] & BIT(1);
1237 
1238 	return phy;
1239 }
1240 
1241 static int mvebu_a3700_comphy_probe(struct platform_device *pdev)
1242 {
1243 	struct mvebu_a3700_comphy_priv *priv;
1244 	struct phy_provider *provider;
1245 	struct device_node *child;
1246 	struct resource *res;
1247 	struct clk *clk;
1248 	int ret;
1249 
1250 	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
1251 	if (!priv)
1252 		return -ENOMEM;
1253 
1254 	spin_lock_init(&priv->lock);
1255 
1256 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "comphy");
1257 	priv->comphy_regs = devm_ioremap_resource(&pdev->dev, res);
1258 	if (IS_ERR(priv->comphy_regs))
1259 		return PTR_ERR(priv->comphy_regs);
1260 
1261 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
1262 					   "lane1_pcie_gbe");
1263 	priv->lane1_phy_regs = devm_ioremap_resource(&pdev->dev, res);
1264 	if (IS_ERR(priv->lane1_phy_regs))
1265 		return PTR_ERR(priv->lane1_phy_regs);
1266 
1267 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
1268 					   "lane0_usb3_gbe");
1269 	priv->lane0_phy_regs = devm_ioremap_resource(&pdev->dev, res);
1270 	if (IS_ERR(priv->lane0_phy_regs))
1271 		return PTR_ERR(priv->lane0_phy_regs);
1272 
1273 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
1274 					   "lane2_sata_usb3");
1275 	priv->lane2_phy_indirect = devm_ioremap_resource(&pdev->dev, res);
1276 	if (IS_ERR(priv->lane2_phy_indirect))
1277 		return PTR_ERR(priv->lane2_phy_indirect);
1278 
1279 	/*
1280 	 * Driver needs to know if reference xtal clock is 40MHz or 25MHz.
1281 	 * Old DT bindings do not have xtal clk present. So do not fail here
1282 	 * and expects that default 25MHz reference clock is used.
1283 	 */
1284 	clk = clk_get(&pdev->dev, "xtal");
1285 	if (IS_ERR(clk)) {
1286 		if (PTR_ERR(clk) == -EPROBE_DEFER)
1287 			return -EPROBE_DEFER;
1288 		dev_warn(&pdev->dev, "missing 'xtal' clk (%ld)\n",
1289 			 PTR_ERR(clk));
1290 	} else {
1291 		ret = clk_prepare_enable(clk);
1292 		if (ret) {
1293 			dev_warn(&pdev->dev, "enabling xtal clk failed (%d)\n",
1294 				 ret);
1295 		} else {
1296 			if (clk_get_rate(clk) == 40000000)
1297 				priv->xtal_is_40m = true;
1298 			clk_disable_unprepare(clk);
1299 		}
1300 		clk_put(clk);
1301 	}
1302 
1303 	dev_set_drvdata(&pdev->dev, priv);
1304 
1305 	for_each_available_child_of_node(pdev->dev.of_node, child) {
1306 		struct mvebu_a3700_comphy_lane *lane;
1307 		struct phy *phy;
1308 		int ret;
1309 		u32 lane_id;
1310 
1311 		ret = of_property_read_u32(child, "reg", &lane_id);
1312 		if (ret < 0) {
1313 			dev_err(&pdev->dev, "missing 'reg' property (%d)\n",
1314 				ret);
1315 			continue;
1316 		}
1317 
1318 		if (lane_id >= 3) {
1319 			dev_err(&pdev->dev, "invalid 'reg' property\n");
1320 			continue;
1321 		}
1322 
1323 		lane = devm_kzalloc(&pdev->dev, sizeof(*lane), GFP_KERNEL);
1324 		if (!lane) {
1325 			of_node_put(child);
1326 			return -ENOMEM;
1327 		}
1328 
1329 		phy = devm_phy_create(&pdev->dev, child,
1330 				      &mvebu_a3700_comphy_ops);
1331 		if (IS_ERR(phy)) {
1332 			of_node_put(child);
1333 			return PTR_ERR(phy);
1334 		}
1335 
1336 		lane->priv = priv;
1337 		lane->dev = &pdev->dev;
1338 		lane->mode = PHY_MODE_INVALID;
1339 		lane->submode = PHY_INTERFACE_MODE_NA;
1340 		lane->id = lane_id;
1341 		lane->invert_tx = false;
1342 		lane->invert_rx = false;
1343 		phy_set_drvdata(phy, lane);
1344 
1345 		/*
1346 		 * To avoid relying on the bootloader/firmware configuration,
1347 		 * power off all comphys.
1348 		 */
1349 		mvebu_a3700_comphy_power_off(phy);
1350 	}
1351 
1352 	provider = devm_of_phy_provider_register(&pdev->dev,
1353 						 mvebu_a3700_comphy_xlate);
1354 
1355 	return PTR_ERR_OR_ZERO(provider);
1356 }
1357 
1358 static const struct of_device_id mvebu_a3700_comphy_of_match_table[] = {
1359 	{ .compatible = "marvell,comphy-a3700" },
1360 	{ },
1361 };
1362 MODULE_DEVICE_TABLE(of, mvebu_a3700_comphy_of_match_table);
1363 
1364 static struct platform_driver mvebu_a3700_comphy_driver = {
1365 	.probe	= mvebu_a3700_comphy_probe,
1366 	.driver	= {
1367 		.name = "mvebu-a3700-comphy",
1368 		.of_match_table = mvebu_a3700_comphy_of_match_table,
1369 	},
1370 };
1371 module_platform_driver(mvebu_a3700_comphy_driver);
1372 
1373 MODULE_AUTHOR("Miquèl Raynal <miquel.raynal@bootlin.com>");
1374 MODULE_AUTHOR("Pali Rohár <pali@kernel.org>");
1375 MODULE_AUTHOR("Marek Behún <kabel@kernel.org>");
1376 MODULE_DESCRIPTION("Common PHY driver for A3700");
1377 MODULE_LICENSE("GPL v2");
1378