1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * Broadcom SATA3 AHCI Controller PHY Driver 4 * 5 * Copyright (C) 2016 Broadcom 6 */ 7 8 #include <linux/delay.h> 9 #include <linux/device.h> 10 #include <linux/init.h> 11 #include <linux/interrupt.h> 12 #include <linux/io.h> 13 #include <linux/kernel.h> 14 #include <linux/module.h> 15 #include <linux/of.h> 16 #include <linux/phy/phy.h> 17 #include <linux/platform_device.h> 18 19 #define SATA_PCB_BANK_OFFSET 0x23c 20 #define SATA_PCB_REG_OFFSET(ofs) ((ofs) * 4) 21 22 #define MAX_PORTS 2 23 24 /* Register offset between PHYs in PCB space */ 25 #define SATA_PCB_REG_28NM_SPACE_SIZE 0x1000 26 27 /* The older SATA PHY registers duplicated per port registers within the map, 28 * rather than having a separate map per port. 29 */ 30 #define SATA_PCB_REG_40NM_SPACE_SIZE 0x10 31 32 /* Register offset between PHYs in PHY control space */ 33 #define SATA_PHY_CTRL_REG_28NM_SPACE_SIZE 0x8 34 35 enum brcm_sata_phy_version { 36 BRCM_SATA_PHY_STB_16NM, 37 BRCM_SATA_PHY_STB_28NM, 38 BRCM_SATA_PHY_STB_40NM, 39 BRCM_SATA_PHY_IPROC_NS2, 40 BRCM_SATA_PHY_IPROC_NSP, 41 BRCM_SATA_PHY_IPROC_SR, 42 BRCM_SATA_PHY_DSL_28NM, 43 }; 44 45 enum brcm_sata_phy_rxaeq_mode { 46 RXAEQ_MODE_OFF = 0, 47 RXAEQ_MODE_AUTO, 48 RXAEQ_MODE_MANUAL, 49 }; 50 51 static enum brcm_sata_phy_rxaeq_mode rxaeq_to_val(const char *m) 52 { 53 if (!strcmp(m, "auto")) 54 return RXAEQ_MODE_AUTO; 55 else if (!strcmp(m, "manual")) 56 return RXAEQ_MODE_MANUAL; 57 else 58 return RXAEQ_MODE_OFF; 59 } 60 61 struct brcm_sata_port { 62 int portnum; 63 struct phy *phy; 64 struct brcm_sata_phy *phy_priv; 65 bool ssc_en; 66 enum brcm_sata_phy_rxaeq_mode rxaeq_mode; 67 u32 rxaeq_val; 68 u32 tx_amplitude_val; 69 }; 70 71 struct brcm_sata_phy { 72 struct device *dev; 73 void __iomem *phy_base; 74 void __iomem *ctrl_base; 75 enum brcm_sata_phy_version version; 76 77 struct brcm_sata_port phys[MAX_PORTS]; 78 }; 79 80 enum sata_phy_regs { 81 BLOCK0_REG_BANK = 0x000, 82 BLOCK0_XGXSSTATUS = 0x81, 83 BLOCK0_XGXSSTATUS_PLL_LOCK = BIT(12), 84 BLOCK0_SPARE = 0x8d, 85 BLOCK0_SPARE_OOB_CLK_SEL_MASK = 0x3, 86 BLOCK0_SPARE_OOB_CLK_SEL_REFBY2 = 0x1, 87 88 BLOCK1_REG_BANK = 0x10, 89 BLOCK1_TEST_TX = 0x83, 90 BLOCK1_TEST_TX_AMP_SHIFT = 12, 91 92 PLL_REG_BANK_0 = 0x050, 93 PLL_REG_BANK_0_PLLCONTROL_0 = 0x81, 94 PLLCONTROL_0_FREQ_DET_RESTART = BIT(13), 95 PLLCONTROL_0_FREQ_MONITOR = BIT(12), 96 PLLCONTROL_0_SEQ_START = BIT(15), 97 PLL_CAP_CHARGE_TIME = 0x83, 98 PLL_VCO_CAL_THRESH = 0x84, 99 PLL_CAP_CONTROL = 0x85, 100 PLL_FREQ_DET_TIME = 0x86, 101 PLL_ACTRL2 = 0x8b, 102 PLL_ACTRL2_SELDIV_MASK = 0x1f, 103 PLL_ACTRL2_SELDIV_SHIFT = 9, 104 PLL_ACTRL6 = 0x86, 105 106 PLL1_REG_BANK = 0x060, 107 PLL1_ACTRL2 = 0x82, 108 PLL1_ACTRL3 = 0x83, 109 PLL1_ACTRL4 = 0x84, 110 PLL1_ACTRL5 = 0x85, 111 PLL1_ACTRL6 = 0x86, 112 PLL1_ACTRL7 = 0x87, 113 PLL1_ACTRL8 = 0x88, 114 115 TX_REG_BANK = 0x070, 116 TX_ACTRL0 = 0x80, 117 TX_ACTRL0_TXPOL_FLIP = BIT(6), 118 TX_ACTRL5 = 0x85, 119 TX_ACTRL5_SSC_EN = BIT(11), 120 121 AEQRX_REG_BANK_0 = 0xd0, 122 AEQ_CONTROL1 = 0x81, 123 AEQ_CONTROL1_ENABLE = BIT(2), 124 AEQ_CONTROL1_FREEZE = BIT(3), 125 AEQ_FRC_EQ = 0x83, 126 AEQ_FRC_EQ_FORCE = BIT(0), 127 AEQ_FRC_EQ_FORCE_VAL = BIT(1), 128 AEQ_RFZ_FRC_VAL = BIT(8), 129 AEQRX_REG_BANK_1 = 0xe0, 130 AEQRX_SLCAL0_CTRL0 = 0x82, 131 AEQRX_SLCAL1_CTRL0 = 0x86, 132 133 OOB_REG_BANK = 0x150, 134 OOB1_REG_BANK = 0x160, 135 OOB_CTRL1 = 0x80, 136 OOB_CTRL1_BURST_MAX_MASK = 0xf, 137 OOB_CTRL1_BURST_MAX_SHIFT = 12, 138 OOB_CTRL1_BURST_MIN_MASK = 0xf, 139 OOB_CTRL1_BURST_MIN_SHIFT = 8, 140 OOB_CTRL1_WAKE_IDLE_MAX_MASK = 0xf, 141 OOB_CTRL1_WAKE_IDLE_MAX_SHIFT = 4, 142 OOB_CTRL1_WAKE_IDLE_MIN_MASK = 0xf, 143 OOB_CTRL1_WAKE_IDLE_MIN_SHIFT = 0, 144 OOB_CTRL2 = 0x81, 145 OOB_CTRL2_SEL_ENA_SHIFT = 15, 146 OOB_CTRL2_SEL_ENA_RC_SHIFT = 14, 147 OOB_CTRL2_RESET_IDLE_MAX_MASK = 0x3f, 148 OOB_CTRL2_RESET_IDLE_MAX_SHIFT = 8, 149 OOB_CTRL2_BURST_CNT_MASK = 0x3, 150 OOB_CTRL2_BURST_CNT_SHIFT = 6, 151 OOB_CTRL2_RESET_IDLE_MIN_MASK = 0x3f, 152 OOB_CTRL2_RESET_IDLE_MIN_SHIFT = 0, 153 154 TXPMD_REG_BANK = 0x1a0, 155 TXPMD_CONTROL1 = 0x81, 156 TXPMD_CONTROL1_TX_SSC_EN_FRC = BIT(0), 157 TXPMD_CONTROL1_TX_SSC_EN_FRC_VAL = BIT(1), 158 TXPMD_TX_FREQ_CTRL_CONTROL1 = 0x82, 159 TXPMD_TX_FREQ_CTRL_CONTROL2 = 0x83, 160 TXPMD_TX_FREQ_CTRL_CONTROL2_FMIN_MASK = 0x3ff, 161 TXPMD_TX_FREQ_CTRL_CONTROL3 = 0x84, 162 TXPMD_TX_FREQ_CTRL_CONTROL3_FMAX_MASK = 0x3ff, 163 164 RXPMD_REG_BANK = 0x1c0, 165 RXPMD_RX_CDR_CONTROL1 = 0x81, 166 RXPMD_RX_PPM_VAL_MASK = 0x1ff, 167 RXPMD_RXPMD_EN_FRC = BIT(12), 168 RXPMD_RXPMD_EN_FRC_VAL = BIT(13), 169 RXPMD_RX_CDR_CDR_PROP_BW = 0x82, 170 RXPMD_G_CDR_PROP_BW_MASK = 0x7, 171 RXPMD_G1_CDR_PROP_BW_SHIFT = 0, 172 RXPMD_G2_CDR_PROP_BW_SHIFT = 3, 173 RXPMD_G3_CDR_PROB_BW_SHIFT = 6, 174 RXPMD_RX_CDR_CDR_ACQ_INTEG_BW = 0x83, 175 RXPMD_G_CDR_ACQ_INT_BW_MASK = 0x7, 176 RXPMD_G1_CDR_ACQ_INT_BW_SHIFT = 0, 177 RXPMD_G2_CDR_ACQ_INT_BW_SHIFT = 3, 178 RXPMD_G3_CDR_ACQ_INT_BW_SHIFT = 6, 179 RXPMD_RX_CDR_CDR_LOCK_INTEG_BW = 0x84, 180 RXPMD_G_CDR_LOCK_INT_BW_MASK = 0x7, 181 RXPMD_G1_CDR_LOCK_INT_BW_SHIFT = 0, 182 RXPMD_G2_CDR_LOCK_INT_BW_SHIFT = 3, 183 RXPMD_G3_CDR_LOCK_INT_BW_SHIFT = 6, 184 RXPMD_RX_FREQ_MON_CONTROL1 = 0x87, 185 RXPMD_MON_CORRECT_EN = BIT(8), 186 RXPMD_MON_MARGIN_VAL_MASK = 0xff, 187 }; 188 189 enum sata_phy_ctrl_regs { 190 PHY_CTRL_1 = 0x0, 191 PHY_CTRL_1_RESET = BIT(0), 192 }; 193 194 static inline void __iomem *brcm_sata_ctrl_base(struct brcm_sata_port *port) 195 { 196 struct brcm_sata_phy *priv = port->phy_priv; 197 u32 size = 0; 198 199 switch (priv->version) { 200 case BRCM_SATA_PHY_IPROC_NS2: 201 size = SATA_PHY_CTRL_REG_28NM_SPACE_SIZE; 202 break; 203 default: 204 dev_err(priv->dev, "invalid phy version\n"); 205 break; 206 } 207 208 return priv->ctrl_base + (port->portnum * size); 209 } 210 211 static void brcm_sata_phy_wr(struct brcm_sata_port *port, u32 bank, 212 u32 ofs, u32 msk, u32 value) 213 { 214 struct brcm_sata_phy *priv = port->phy_priv; 215 void __iomem *pcb_base = priv->phy_base; 216 u32 tmp; 217 218 if (priv->version == BRCM_SATA_PHY_STB_40NM) 219 bank += (port->portnum * SATA_PCB_REG_40NM_SPACE_SIZE); 220 else 221 pcb_base += (port->portnum * SATA_PCB_REG_28NM_SPACE_SIZE); 222 223 writel(bank, pcb_base + SATA_PCB_BANK_OFFSET); 224 tmp = readl(pcb_base + SATA_PCB_REG_OFFSET(ofs)); 225 tmp = (tmp & msk) | value; 226 writel(tmp, pcb_base + SATA_PCB_REG_OFFSET(ofs)); 227 } 228 229 static u32 brcm_sata_phy_rd(struct brcm_sata_port *port, u32 bank, u32 ofs) 230 { 231 struct brcm_sata_phy *priv = port->phy_priv; 232 void __iomem *pcb_base = priv->phy_base; 233 234 if (priv->version == BRCM_SATA_PHY_STB_40NM) 235 bank += (port->portnum * SATA_PCB_REG_40NM_SPACE_SIZE); 236 else 237 pcb_base += (port->portnum * SATA_PCB_REG_28NM_SPACE_SIZE); 238 239 writel(bank, pcb_base + SATA_PCB_BANK_OFFSET); 240 return readl(pcb_base + SATA_PCB_REG_OFFSET(ofs)); 241 } 242 243 /* These defaults were characterized by H/W group */ 244 #define STB_FMIN_VAL_DEFAULT 0x3df 245 #define STB_FMAX_VAL_DEFAULT 0x3df 246 #define STB_FMAX_VAL_SSC 0x83 247 248 static void brcm_stb_sata_ssc_init(struct brcm_sata_port *port) 249 { 250 struct brcm_sata_phy *priv = port->phy_priv; 251 u32 tmp; 252 253 /* override the TX spread spectrum setting */ 254 tmp = TXPMD_CONTROL1_TX_SSC_EN_FRC_VAL | TXPMD_CONTROL1_TX_SSC_EN_FRC; 255 brcm_sata_phy_wr(port, TXPMD_REG_BANK, TXPMD_CONTROL1, ~tmp, tmp); 256 257 /* set fixed min freq */ 258 brcm_sata_phy_wr(port, TXPMD_REG_BANK, TXPMD_TX_FREQ_CTRL_CONTROL2, 259 ~TXPMD_TX_FREQ_CTRL_CONTROL2_FMIN_MASK, 260 STB_FMIN_VAL_DEFAULT); 261 262 /* set fixed max freq depending on SSC config */ 263 if (port->ssc_en) { 264 dev_info(priv->dev, "enabling SSC on port%d\n", port->portnum); 265 tmp = STB_FMAX_VAL_SSC; 266 } else { 267 tmp = STB_FMAX_VAL_DEFAULT; 268 } 269 270 brcm_sata_phy_wr(port, TXPMD_REG_BANK, TXPMD_TX_FREQ_CTRL_CONTROL3, 271 ~TXPMD_TX_FREQ_CTRL_CONTROL3_FMAX_MASK, tmp); 272 } 273 274 #define AEQ_FRC_EQ_VAL_SHIFT 2 275 #define AEQ_FRC_EQ_VAL_MASK 0x3f 276 277 static int brcm_stb_sata_rxaeq_init(struct brcm_sata_port *port) 278 { 279 u32 tmp = 0, reg = 0; 280 281 switch (port->rxaeq_mode) { 282 case RXAEQ_MODE_OFF: 283 return 0; 284 285 case RXAEQ_MODE_AUTO: 286 reg = AEQ_CONTROL1; 287 tmp = AEQ_CONTROL1_ENABLE | AEQ_CONTROL1_FREEZE; 288 break; 289 290 case RXAEQ_MODE_MANUAL: 291 reg = AEQ_FRC_EQ; 292 tmp = AEQ_FRC_EQ_FORCE | AEQ_FRC_EQ_FORCE_VAL; 293 if (port->rxaeq_val > AEQ_FRC_EQ_VAL_MASK) 294 return -EINVAL; 295 tmp |= port->rxaeq_val << AEQ_FRC_EQ_VAL_SHIFT; 296 break; 297 } 298 299 brcm_sata_phy_wr(port, AEQRX_REG_BANK_0, reg, ~tmp, tmp); 300 brcm_sata_phy_wr(port, AEQRX_REG_BANK_1, reg, ~tmp, tmp); 301 302 return 0; 303 } 304 305 static int brcm_stb_sata_init(struct brcm_sata_port *port) 306 { 307 brcm_stb_sata_ssc_init(port); 308 309 return brcm_stb_sata_rxaeq_init(port); 310 } 311 312 static int brcm_stb_sata_16nm_ssc_init(struct brcm_sata_port *port) 313 { 314 u32 tmp, value; 315 316 /* Reduce CP tail current to 1/16th of its default value */ 317 brcm_sata_phy_wr(port, PLL1_REG_BANK, PLL1_ACTRL6, 0, 0x141); 318 319 /* Turn off CP tail current boost */ 320 brcm_sata_phy_wr(port, PLL1_REG_BANK, PLL1_ACTRL8, 0, 0xc006); 321 322 /* Set a specific AEQ equalizer value */ 323 tmp = AEQ_FRC_EQ_FORCE_VAL | AEQ_FRC_EQ_FORCE; 324 brcm_sata_phy_wr(port, AEQRX_REG_BANK_0, AEQ_FRC_EQ, 325 ~(tmp | AEQ_RFZ_FRC_VAL | 326 AEQ_FRC_EQ_VAL_MASK << AEQ_FRC_EQ_VAL_SHIFT), 327 tmp | 32 << AEQ_FRC_EQ_VAL_SHIFT); 328 329 /* Set RX PPM val center frequency */ 330 if (port->ssc_en) 331 value = 0x52; 332 else 333 value = 0; 334 brcm_sata_phy_wr(port, RXPMD_REG_BANK, RXPMD_RX_CDR_CONTROL1, 335 ~RXPMD_RX_PPM_VAL_MASK, value); 336 337 /* Set proportional loop bandwith Gen1/2/3 */ 338 tmp = RXPMD_G_CDR_PROP_BW_MASK << RXPMD_G1_CDR_PROP_BW_SHIFT | 339 RXPMD_G_CDR_PROP_BW_MASK << RXPMD_G2_CDR_PROP_BW_SHIFT | 340 RXPMD_G_CDR_PROP_BW_MASK << RXPMD_G3_CDR_PROB_BW_SHIFT; 341 if (port->ssc_en) 342 value = 2 << RXPMD_G1_CDR_PROP_BW_SHIFT | 343 2 << RXPMD_G2_CDR_PROP_BW_SHIFT | 344 2 << RXPMD_G3_CDR_PROB_BW_SHIFT; 345 else 346 value = 1 << RXPMD_G1_CDR_PROP_BW_SHIFT | 347 1 << RXPMD_G2_CDR_PROP_BW_SHIFT | 348 1 << RXPMD_G3_CDR_PROB_BW_SHIFT; 349 brcm_sata_phy_wr(port, RXPMD_REG_BANK, RXPMD_RX_CDR_CDR_PROP_BW, ~tmp, 350 value); 351 352 /* Set CDR integral loop acquisition bandwidth for Gen1/2/3 */ 353 tmp = RXPMD_G_CDR_ACQ_INT_BW_MASK << RXPMD_G1_CDR_ACQ_INT_BW_SHIFT | 354 RXPMD_G_CDR_ACQ_INT_BW_MASK << RXPMD_G2_CDR_ACQ_INT_BW_SHIFT | 355 RXPMD_G_CDR_ACQ_INT_BW_MASK << RXPMD_G3_CDR_ACQ_INT_BW_SHIFT; 356 if (port->ssc_en) 357 value = 1 << RXPMD_G1_CDR_ACQ_INT_BW_SHIFT | 358 1 << RXPMD_G2_CDR_ACQ_INT_BW_SHIFT | 359 1 << RXPMD_G3_CDR_ACQ_INT_BW_SHIFT; 360 else 361 value = 0; 362 brcm_sata_phy_wr(port, RXPMD_REG_BANK, RXPMD_RX_CDR_CDR_ACQ_INTEG_BW, 363 ~tmp, value); 364 365 /* Set CDR integral loop locking bandwidth to 1 for Gen 1/2/3 */ 366 tmp = RXPMD_G_CDR_LOCK_INT_BW_MASK << RXPMD_G1_CDR_LOCK_INT_BW_SHIFT | 367 RXPMD_G_CDR_LOCK_INT_BW_MASK << RXPMD_G2_CDR_LOCK_INT_BW_SHIFT | 368 RXPMD_G_CDR_LOCK_INT_BW_MASK << RXPMD_G3_CDR_LOCK_INT_BW_SHIFT; 369 if (port->ssc_en) 370 value = 1 << RXPMD_G1_CDR_LOCK_INT_BW_SHIFT | 371 1 << RXPMD_G2_CDR_LOCK_INT_BW_SHIFT | 372 1 << RXPMD_G3_CDR_LOCK_INT_BW_SHIFT; 373 else 374 value = 0; 375 brcm_sata_phy_wr(port, RXPMD_REG_BANK, RXPMD_RX_CDR_CDR_LOCK_INTEG_BW, 376 ~tmp, value); 377 378 /* Set no guard band and clamp CDR */ 379 tmp = RXPMD_MON_CORRECT_EN | RXPMD_MON_MARGIN_VAL_MASK; 380 if (port->ssc_en) 381 value = 0x51; 382 else 383 value = 0; 384 brcm_sata_phy_wr(port, RXPMD_REG_BANK, RXPMD_RX_FREQ_MON_CONTROL1, 385 ~tmp, RXPMD_MON_CORRECT_EN | value); 386 387 tmp = GENMASK(15, 12); 388 switch (port->tx_amplitude_val) { 389 case 400: 390 value = BIT(12) | BIT(13); 391 break; 392 case 500: 393 value = BIT(13); 394 break; 395 case 600: 396 value = BIT(12); 397 break; 398 case 800: 399 value = 0; 400 break; 401 default: 402 value = tmp; 403 break; 404 } 405 406 if (value != tmp) 407 brcm_sata_phy_wr(port, BLOCK1_REG_BANK, BLOCK1_TEST_TX, ~tmp, 408 value); 409 410 /* Turn on/off SSC */ 411 brcm_sata_phy_wr(port, TX_REG_BANK, TX_ACTRL5, ~TX_ACTRL5_SSC_EN, 412 port->ssc_en ? TX_ACTRL5_SSC_EN : 0); 413 414 return 0; 415 } 416 417 static int brcm_stb_sata_16nm_init(struct brcm_sata_port *port) 418 { 419 return brcm_stb_sata_16nm_ssc_init(port); 420 } 421 422 /* NS2 SATA PLL1 defaults were characterized by H/W group */ 423 #define NS2_PLL1_ACTRL2_MAGIC 0x1df8 424 #define NS2_PLL1_ACTRL3_MAGIC 0x2b00 425 #define NS2_PLL1_ACTRL4_MAGIC 0x8824 426 427 static int brcm_ns2_sata_init(struct brcm_sata_port *port) 428 { 429 int try; 430 unsigned int val; 431 void __iomem *ctrl_base = brcm_sata_ctrl_base(port); 432 struct device *dev = port->phy_priv->dev; 433 434 /* Configure OOB control */ 435 val = 0x0; 436 val |= (0xc << OOB_CTRL1_BURST_MAX_SHIFT); 437 val |= (0x4 << OOB_CTRL1_BURST_MIN_SHIFT); 438 val |= (0x9 << OOB_CTRL1_WAKE_IDLE_MAX_SHIFT); 439 val |= (0x3 << OOB_CTRL1_WAKE_IDLE_MIN_SHIFT); 440 brcm_sata_phy_wr(port, OOB_REG_BANK, OOB_CTRL1, 0x0, val); 441 val = 0x0; 442 val |= (0x1b << OOB_CTRL2_RESET_IDLE_MAX_SHIFT); 443 val |= (0x2 << OOB_CTRL2_BURST_CNT_SHIFT); 444 val |= (0x9 << OOB_CTRL2_RESET_IDLE_MIN_SHIFT); 445 brcm_sata_phy_wr(port, OOB_REG_BANK, OOB_CTRL2, 0x0, val); 446 447 /* Configure PHY PLL register bank 1 */ 448 val = NS2_PLL1_ACTRL2_MAGIC; 449 brcm_sata_phy_wr(port, PLL1_REG_BANK, PLL1_ACTRL2, 0x0, val); 450 val = NS2_PLL1_ACTRL3_MAGIC; 451 brcm_sata_phy_wr(port, PLL1_REG_BANK, PLL1_ACTRL3, 0x0, val); 452 val = NS2_PLL1_ACTRL4_MAGIC; 453 brcm_sata_phy_wr(port, PLL1_REG_BANK, PLL1_ACTRL4, 0x0, val); 454 455 /* Configure PHY BLOCK0 register bank */ 456 /* Set oob_clk_sel to refclk/2 */ 457 brcm_sata_phy_wr(port, BLOCK0_REG_BANK, BLOCK0_SPARE, 458 ~BLOCK0_SPARE_OOB_CLK_SEL_MASK, 459 BLOCK0_SPARE_OOB_CLK_SEL_REFBY2); 460 461 /* Strobe PHY reset using PHY control register */ 462 writel(PHY_CTRL_1_RESET, ctrl_base + PHY_CTRL_1); 463 mdelay(1); 464 writel(0x0, ctrl_base + PHY_CTRL_1); 465 mdelay(1); 466 467 /* Wait for PHY PLL lock by polling pll_lock bit */ 468 try = 50; 469 while (try) { 470 val = brcm_sata_phy_rd(port, BLOCK0_REG_BANK, 471 BLOCK0_XGXSSTATUS); 472 if (val & BLOCK0_XGXSSTATUS_PLL_LOCK) 473 break; 474 msleep(20); 475 try--; 476 } 477 if (!try) { 478 /* PLL did not lock; give up */ 479 dev_err(dev, "port%d PLL did not lock\n", port->portnum); 480 return -ETIMEDOUT; 481 } 482 483 dev_dbg(dev, "port%d initialized\n", port->portnum); 484 485 return 0; 486 } 487 488 static int brcm_nsp_sata_init(struct brcm_sata_port *port) 489 { 490 struct device *dev = port->phy_priv->dev; 491 unsigned int oob_bank; 492 unsigned int val, try; 493 494 /* Configure OOB control */ 495 if (port->portnum == 0) 496 oob_bank = OOB_REG_BANK; 497 else if (port->portnum == 1) 498 oob_bank = OOB1_REG_BANK; 499 else 500 return -EINVAL; 501 502 val = 0x0; 503 val |= (0x0f << OOB_CTRL1_BURST_MAX_SHIFT); 504 val |= (0x06 << OOB_CTRL1_BURST_MIN_SHIFT); 505 val |= (0x0f << OOB_CTRL1_WAKE_IDLE_MAX_SHIFT); 506 val |= (0x06 << OOB_CTRL1_WAKE_IDLE_MIN_SHIFT); 507 brcm_sata_phy_wr(port, oob_bank, OOB_CTRL1, 0x0, val); 508 509 val = 0x0; 510 val |= (0x2e << OOB_CTRL2_RESET_IDLE_MAX_SHIFT); 511 val |= (0x02 << OOB_CTRL2_BURST_CNT_SHIFT); 512 val |= (0x16 << OOB_CTRL2_RESET_IDLE_MIN_SHIFT); 513 brcm_sata_phy_wr(port, oob_bank, OOB_CTRL2, 0x0, val); 514 515 516 brcm_sata_phy_wr(port, PLL_REG_BANK_0, PLL_ACTRL2, 517 ~(PLL_ACTRL2_SELDIV_MASK << PLL_ACTRL2_SELDIV_SHIFT), 518 0x0c << PLL_ACTRL2_SELDIV_SHIFT); 519 520 brcm_sata_phy_wr(port, PLL_REG_BANK_0, PLL_CAP_CONTROL, 521 0xff0, 0x4f0); 522 523 val = PLLCONTROL_0_FREQ_DET_RESTART | PLLCONTROL_0_FREQ_MONITOR; 524 brcm_sata_phy_wr(port, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0, 525 ~val, val); 526 val = PLLCONTROL_0_SEQ_START; 527 brcm_sata_phy_wr(port, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0, 528 ~val, 0); 529 mdelay(10); 530 brcm_sata_phy_wr(port, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0, 531 ~val, val); 532 533 /* Wait for pll_seq_done bit */ 534 try = 50; 535 while (--try) { 536 val = brcm_sata_phy_rd(port, BLOCK0_REG_BANK, 537 BLOCK0_XGXSSTATUS); 538 if (val & BLOCK0_XGXSSTATUS_PLL_LOCK) 539 break; 540 msleep(20); 541 } 542 if (!try) { 543 /* PLL did not lock; give up */ 544 dev_err(dev, "port%d PLL did not lock\n", port->portnum); 545 return -ETIMEDOUT; 546 } 547 548 dev_dbg(dev, "port%d initialized\n", port->portnum); 549 550 return 0; 551 } 552 553 /* SR PHY PLL0 registers */ 554 #define SR_PLL0_ACTRL6_MAGIC 0xa 555 556 /* SR PHY PLL1 registers */ 557 #define SR_PLL1_ACTRL2_MAGIC 0x32 558 #define SR_PLL1_ACTRL3_MAGIC 0x2 559 #define SR_PLL1_ACTRL4_MAGIC 0x3e8 560 561 static int brcm_sr_sata_init(struct brcm_sata_port *port) 562 { 563 struct device *dev = port->phy_priv->dev; 564 unsigned int val, try; 565 566 /* Configure PHY PLL register bank 1 */ 567 val = SR_PLL1_ACTRL2_MAGIC; 568 brcm_sata_phy_wr(port, PLL1_REG_BANK, PLL1_ACTRL2, 0x0, val); 569 val = SR_PLL1_ACTRL3_MAGIC; 570 brcm_sata_phy_wr(port, PLL1_REG_BANK, PLL1_ACTRL3, 0x0, val); 571 val = SR_PLL1_ACTRL4_MAGIC; 572 brcm_sata_phy_wr(port, PLL1_REG_BANK, PLL1_ACTRL4, 0x0, val); 573 574 /* Configure PHY PLL register bank 0 */ 575 val = SR_PLL0_ACTRL6_MAGIC; 576 brcm_sata_phy_wr(port, PLL_REG_BANK_0, PLL_ACTRL6, 0x0, val); 577 578 /* Wait for PHY PLL lock by polling pll_lock bit */ 579 try = 50; 580 do { 581 val = brcm_sata_phy_rd(port, BLOCK0_REG_BANK, 582 BLOCK0_XGXSSTATUS); 583 if (val & BLOCK0_XGXSSTATUS_PLL_LOCK) 584 break; 585 msleep(20); 586 try--; 587 } while (try); 588 589 if ((val & BLOCK0_XGXSSTATUS_PLL_LOCK) == 0) { 590 /* PLL did not lock; give up */ 591 dev_err(dev, "port%d PLL did not lock\n", port->portnum); 592 return -ETIMEDOUT; 593 } 594 595 /* Invert Tx polarity */ 596 brcm_sata_phy_wr(port, TX_REG_BANK, TX_ACTRL0, 597 ~TX_ACTRL0_TXPOL_FLIP, TX_ACTRL0_TXPOL_FLIP); 598 599 /* Configure OOB control to handle 100MHz reference clock */ 600 val = ((0xc << OOB_CTRL1_BURST_MAX_SHIFT) | 601 (0x4 << OOB_CTRL1_BURST_MIN_SHIFT) | 602 (0x8 << OOB_CTRL1_WAKE_IDLE_MAX_SHIFT) | 603 (0x3 << OOB_CTRL1_WAKE_IDLE_MIN_SHIFT)); 604 brcm_sata_phy_wr(port, OOB_REG_BANK, OOB_CTRL1, 0x0, val); 605 val = ((0x1b << OOB_CTRL2_RESET_IDLE_MAX_SHIFT) | 606 (0x2 << OOB_CTRL2_BURST_CNT_SHIFT) | 607 (0x9 << OOB_CTRL2_RESET_IDLE_MIN_SHIFT)); 608 brcm_sata_phy_wr(port, OOB_REG_BANK, OOB_CTRL2, 0x0, val); 609 610 return 0; 611 } 612 613 static int brcm_dsl_sata_init(struct brcm_sata_port *port) 614 { 615 struct device *dev = port->phy_priv->dev; 616 unsigned int try; 617 u32 tmp; 618 619 brcm_sata_phy_wr(port, PLL1_REG_BANK, PLL1_ACTRL7, 0, 0x873); 620 621 brcm_sata_phy_wr(port, PLL1_REG_BANK, PLL1_ACTRL6, 0, 0xc000); 622 623 brcm_sata_phy_wr(port, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0, 624 0, 0x3089); 625 usleep_range(1000, 2000); 626 627 brcm_sata_phy_wr(port, PLL_REG_BANK_0, PLL_REG_BANK_0_PLLCONTROL_0, 628 0, 0x3088); 629 usleep_range(1000, 2000); 630 631 brcm_sata_phy_wr(port, AEQRX_REG_BANK_1, AEQRX_SLCAL0_CTRL0, 632 0, 0x3000); 633 634 brcm_sata_phy_wr(port, AEQRX_REG_BANK_1, AEQRX_SLCAL1_CTRL0, 635 0, 0x3000); 636 usleep_range(1000, 2000); 637 638 brcm_sata_phy_wr(port, PLL_REG_BANK_0, PLL_CAP_CHARGE_TIME, 0, 0x32); 639 640 brcm_sata_phy_wr(port, PLL_REG_BANK_0, PLL_VCO_CAL_THRESH, 0, 0xa); 641 642 brcm_sata_phy_wr(port, PLL_REG_BANK_0, PLL_FREQ_DET_TIME, 0, 0x64); 643 usleep_range(1000, 2000); 644 645 /* Acquire PLL lock */ 646 try = 50; 647 while (try) { 648 tmp = brcm_sata_phy_rd(port, BLOCK0_REG_BANK, 649 BLOCK0_XGXSSTATUS); 650 if (tmp & BLOCK0_XGXSSTATUS_PLL_LOCK) 651 break; 652 msleep(20); 653 try--; 654 } 655 656 if (!try) { 657 /* PLL did not lock; give up */ 658 dev_err(dev, "port%d PLL did not lock\n", port->portnum); 659 return -ETIMEDOUT; 660 } 661 662 dev_dbg(dev, "port%d initialized\n", port->portnum); 663 664 return 0; 665 } 666 667 static int brcm_sata_phy_init(struct phy *phy) 668 { 669 int rc; 670 struct brcm_sata_port *port = phy_get_drvdata(phy); 671 672 switch (port->phy_priv->version) { 673 case BRCM_SATA_PHY_STB_16NM: 674 rc = brcm_stb_sata_16nm_init(port); 675 break; 676 case BRCM_SATA_PHY_STB_28NM: 677 case BRCM_SATA_PHY_STB_40NM: 678 rc = brcm_stb_sata_init(port); 679 break; 680 case BRCM_SATA_PHY_IPROC_NS2: 681 rc = brcm_ns2_sata_init(port); 682 break; 683 case BRCM_SATA_PHY_IPROC_NSP: 684 rc = brcm_nsp_sata_init(port); 685 break; 686 case BRCM_SATA_PHY_IPROC_SR: 687 rc = brcm_sr_sata_init(port); 688 break; 689 case BRCM_SATA_PHY_DSL_28NM: 690 rc = brcm_dsl_sata_init(port); 691 break; 692 default: 693 rc = -ENODEV; 694 } 695 696 return rc; 697 } 698 699 static void brcm_stb_sata_calibrate(struct brcm_sata_port *port) 700 { 701 u32 tmp = BIT(8); 702 703 brcm_sata_phy_wr(port, RXPMD_REG_BANK, RXPMD_RX_FREQ_MON_CONTROL1, 704 ~tmp, tmp); 705 } 706 707 static int brcm_sata_phy_calibrate(struct phy *phy) 708 { 709 struct brcm_sata_port *port = phy_get_drvdata(phy); 710 int rc = -EOPNOTSUPP; 711 712 switch (port->phy_priv->version) { 713 case BRCM_SATA_PHY_STB_28NM: 714 case BRCM_SATA_PHY_STB_40NM: 715 brcm_stb_sata_calibrate(port); 716 rc = 0; 717 break; 718 default: 719 break; 720 } 721 722 return rc; 723 } 724 725 static const struct phy_ops phy_ops = { 726 .init = brcm_sata_phy_init, 727 .calibrate = brcm_sata_phy_calibrate, 728 .owner = THIS_MODULE, 729 }; 730 731 static const struct of_device_id brcm_sata_phy_of_match[] = { 732 { .compatible = "brcm,bcm7216-sata-phy", 733 .data = (void *)BRCM_SATA_PHY_STB_16NM }, 734 { .compatible = "brcm,bcm7445-sata-phy", 735 .data = (void *)BRCM_SATA_PHY_STB_28NM }, 736 { .compatible = "brcm,bcm7425-sata-phy", 737 .data = (void *)BRCM_SATA_PHY_STB_40NM }, 738 { .compatible = "brcm,iproc-ns2-sata-phy", 739 .data = (void *)BRCM_SATA_PHY_IPROC_NS2 }, 740 { .compatible = "brcm,iproc-nsp-sata-phy", 741 .data = (void *)BRCM_SATA_PHY_IPROC_NSP }, 742 { .compatible = "brcm,iproc-sr-sata-phy", 743 .data = (void *)BRCM_SATA_PHY_IPROC_SR }, 744 { .compatible = "brcm,bcm63138-sata-phy", 745 .data = (void *)BRCM_SATA_PHY_DSL_28NM }, 746 {}, 747 }; 748 MODULE_DEVICE_TABLE(of, brcm_sata_phy_of_match); 749 750 static int brcm_sata_phy_probe(struct platform_device *pdev) 751 { 752 const char *rxaeq_mode; 753 struct device *dev = &pdev->dev; 754 struct device_node *dn = dev->of_node, *child; 755 const struct of_device_id *of_id; 756 struct brcm_sata_phy *priv; 757 struct phy_provider *provider; 758 int ret, count = 0; 759 760 if (of_get_child_count(dn) == 0) 761 return -ENODEV; 762 763 priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); 764 if (!priv) 765 return -ENOMEM; 766 dev_set_drvdata(dev, priv); 767 priv->dev = dev; 768 769 priv->phy_base = devm_platform_ioremap_resource_byname(pdev, "phy"); 770 if (IS_ERR(priv->phy_base)) 771 return PTR_ERR(priv->phy_base); 772 773 of_id = of_match_node(brcm_sata_phy_of_match, dn); 774 if (of_id) 775 priv->version = (uintptr_t)of_id->data; 776 else 777 priv->version = BRCM_SATA_PHY_STB_28NM; 778 779 if (priv->version == BRCM_SATA_PHY_IPROC_NS2) { 780 priv->ctrl_base = devm_platform_ioremap_resource_byname(pdev, "phy-ctrl"); 781 if (IS_ERR(priv->ctrl_base)) 782 return PTR_ERR(priv->ctrl_base); 783 } 784 785 for_each_available_child_of_node(dn, child) { 786 unsigned int id; 787 struct brcm_sata_port *port; 788 789 if (of_property_read_u32(child, "reg", &id)) { 790 dev_err(dev, "missing reg property in node %pOFn\n", 791 child); 792 ret = -EINVAL; 793 goto put_child; 794 } 795 796 if (id >= MAX_PORTS) { 797 dev_err(dev, "invalid reg: %u\n", id); 798 ret = -EINVAL; 799 goto put_child; 800 } 801 if (priv->phys[id].phy) { 802 dev_err(dev, "already registered port %u\n", id); 803 ret = -EINVAL; 804 goto put_child; 805 } 806 807 port = &priv->phys[id]; 808 port->portnum = id; 809 port->phy_priv = priv; 810 port->phy = devm_phy_create(dev, child, &phy_ops); 811 port->rxaeq_mode = RXAEQ_MODE_OFF; 812 if (!of_property_read_string(child, "brcm,rxaeq-mode", 813 &rxaeq_mode)) 814 port->rxaeq_mode = rxaeq_to_val(rxaeq_mode); 815 if (port->rxaeq_mode == RXAEQ_MODE_MANUAL) 816 of_property_read_u32(child, "brcm,rxaeq-value", 817 &port->rxaeq_val); 818 819 of_property_read_u32(child, "brcm,tx-amplitude-millivolt", 820 &port->tx_amplitude_val); 821 822 port->ssc_en = of_property_read_bool(child, "brcm,enable-ssc"); 823 if (IS_ERR(port->phy)) { 824 dev_err(dev, "failed to create PHY\n"); 825 ret = PTR_ERR(port->phy); 826 goto put_child; 827 } 828 829 phy_set_drvdata(port->phy, port); 830 count++; 831 } 832 833 provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); 834 if (IS_ERR(provider)) { 835 dev_err(dev, "could not register PHY provider\n"); 836 return PTR_ERR(provider); 837 } 838 839 dev_info(dev, "registered %d port(s)\n", count); 840 841 return 0; 842 put_child: 843 of_node_put(child); 844 return ret; 845 } 846 847 static struct platform_driver brcm_sata_phy_driver = { 848 .probe = brcm_sata_phy_probe, 849 .driver = { 850 .of_match_table = brcm_sata_phy_of_match, 851 .name = "brcm-sata-phy", 852 } 853 }; 854 module_platform_driver(brcm_sata_phy_driver); 855 856 MODULE_DESCRIPTION("Broadcom SATA PHY driver"); 857 MODULE_LICENSE("GPL"); 858 MODULE_AUTHOR("Marc Carino"); 859 MODULE_AUTHOR("Brian Norris"); 860 MODULE_ALIAS("platform:phy-brcm-sata"); 861