1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3  * Meson8, Meson8b and GXBB USB2 PHY driver
4  *
5  * Copyright (C) 2016 Martin Blumenstingl <martin.blumenstingl@googlemail.com>
6  */
7 
8 #include <linux/clk.h>
9 #include <linux/delay.h>
10 #include <linux/io.h>
11 #include <linux/mod_devicetable.h>
12 #include <linux/module.h>
13 #include <linux/property.h>
14 #include <linux/regmap.h>
15 #include <linux/reset.h>
16 #include <linux/phy/phy.h>
17 #include <linux/platform_device.h>
18 #include <linux/usb/of.h>
19 
20 #define REG_CONFIG					0x00
21 	#define REG_CONFIG_CLK_EN			BIT(0)
22 	#define REG_CONFIG_CLK_SEL_MASK			GENMASK(3, 1)
23 	#define REG_CONFIG_CLK_DIV_MASK			GENMASK(10, 4)
24 	#define REG_CONFIG_CLK_32k_ALTSEL		BIT(15)
25 	#define REG_CONFIG_TEST_TRIG			BIT(31)
26 
27 #define REG_CTRL					0x04
28 	#define REG_CTRL_SOFT_PRST			BIT(0)
29 	#define REG_CTRL_SOFT_HRESET			BIT(1)
30 	#define REG_CTRL_SS_SCALEDOWN_MODE_MASK		GENMASK(3, 2)
31 	#define REG_CTRL_CLK_DET_RST			BIT(4)
32 	#define REG_CTRL_INTR_SEL			BIT(5)
33 	#define REG_CTRL_CLK_DETECTED			BIT(8)
34 	#define REG_CTRL_SOF_SENT_RCVD_TGL		BIT(9)
35 	#define REG_CTRL_SOF_TOGGLE_OUT			BIT(10)
36 	#define REG_CTRL_POWER_ON_RESET			BIT(15)
37 	#define REG_CTRL_SLEEPM				BIT(16)
38 	#define REG_CTRL_TX_BITSTUFF_ENN_H		BIT(17)
39 	#define REG_CTRL_TX_BITSTUFF_ENN		BIT(18)
40 	#define REG_CTRL_COMMON_ON			BIT(19)
41 	#define REG_CTRL_REF_CLK_SEL_MASK		GENMASK(21, 20)
42 	#define REG_CTRL_REF_CLK_SEL_SHIFT		20
43 	#define REG_CTRL_FSEL_MASK			GENMASK(24, 22)
44 	#define REG_CTRL_FSEL_SHIFT			22
45 	#define REG_CTRL_PORT_RESET			BIT(25)
46 	#define REG_CTRL_THREAD_ID_MASK			GENMASK(31, 26)
47 
48 #define REG_ENDP_INTR					0x08
49 
50 /* bits [31:26], [24:21] and [15:3] seem to be read-only */
51 #define REG_ADP_BC					0x0c
52 	#define REG_ADP_BC_VBUS_VLD_EXT_SEL		BIT(0)
53 	#define REG_ADP_BC_VBUS_VLD_EXT			BIT(1)
54 	#define REG_ADP_BC_OTG_DISABLE			BIT(2)
55 	#define REG_ADP_BC_ID_PULLUP			BIT(3)
56 	#define REG_ADP_BC_DRV_VBUS			BIT(4)
57 	#define REG_ADP_BC_ADP_PRB_EN			BIT(5)
58 	#define REG_ADP_BC_ADP_DISCHARGE		BIT(6)
59 	#define REG_ADP_BC_ADP_CHARGE			BIT(7)
60 	#define REG_ADP_BC_SESS_END			BIT(8)
61 	#define REG_ADP_BC_DEVICE_SESS_VLD		BIT(9)
62 	#define REG_ADP_BC_B_VALID			BIT(10)
63 	#define REG_ADP_BC_A_VALID			BIT(11)
64 	#define REG_ADP_BC_ID_DIG			BIT(12)
65 	#define REG_ADP_BC_VBUS_VALID			BIT(13)
66 	#define REG_ADP_BC_ADP_PROBE			BIT(14)
67 	#define REG_ADP_BC_ADP_SENSE			BIT(15)
68 	#define REG_ADP_BC_ACA_ENABLE			BIT(16)
69 	#define REG_ADP_BC_DCD_ENABLE			BIT(17)
70 	#define REG_ADP_BC_VDAT_DET_EN_B		BIT(18)
71 	#define REG_ADP_BC_VDAT_SRC_EN_B		BIT(19)
72 	#define REG_ADP_BC_CHARGE_SEL			BIT(20)
73 	#define REG_ADP_BC_CHARGE_DETECT		BIT(21)
74 	#define REG_ADP_BC_ACA_PIN_RANGE_C		BIT(22)
75 	#define REG_ADP_BC_ACA_PIN_RANGE_B		BIT(23)
76 	#define REG_ADP_BC_ACA_PIN_RANGE_A		BIT(24)
77 	#define REG_ADP_BC_ACA_PIN_GND			BIT(25)
78 	#define REG_ADP_BC_ACA_PIN_FLOAT		BIT(26)
79 
80 #define REG_DBG_UART					0x10
81 	#define REG_DBG_UART_BYPASS_SEL			BIT(0)
82 	#define REG_DBG_UART_BYPASS_DM_EN		BIT(1)
83 	#define REG_DBG_UART_BYPASS_DP_EN		BIT(2)
84 	#define REG_DBG_UART_BYPASS_DM_DATA		BIT(3)
85 	#define REG_DBG_UART_BYPASS_DP_DATA		BIT(4)
86 	#define REG_DBG_UART_FSV_MINUS			BIT(5)
87 	#define REG_DBG_UART_FSV_PLUS			BIT(6)
88 	#define REG_DBG_UART_FSV_BURN_IN_TEST		BIT(7)
89 	#define REG_DBG_UART_LOOPBACK_EN_B		BIT(8)
90 	#define REG_DBG_UART_SET_IDDQ			BIT(9)
91 	#define REG_DBG_UART_ATE_RESET			BIT(10)
92 
93 #define REG_TEST					0x14
94 	#define REG_TEST_DATA_IN_MASK			GENMASK(3, 0)
95 	#define REG_TEST_EN_MASK			GENMASK(7, 4)
96 	#define REG_TEST_ADDR_MASK			GENMASK(11, 8)
97 	#define REG_TEST_DATA_OUT_SEL			BIT(12)
98 	#define REG_TEST_CLK				BIT(13)
99 	#define REG_TEST_VA_TEST_EN_B_MASK		GENMASK(15, 14)
100 	#define REG_TEST_DATA_OUT_MASK			GENMASK(19, 16)
101 	#define REG_TEST_DISABLE_ID_PULLUP		BIT(20)
102 
103 #define REG_TUNE					0x18
104 	#define REG_TUNE_TX_RES_TUNE_MASK		GENMASK(1, 0)
105 	#define REG_TUNE_TX_HSXV_TUNE_MASK		GENMASK(3, 2)
106 	#define REG_TUNE_TX_VREF_TUNE_MASK		GENMASK(7, 4)
107 	#define REG_TUNE_TX_RISE_TUNE_MASK		GENMASK(9, 8)
108 	#define REG_TUNE_TX_PREEMP_PULSE_TUNE		BIT(10)
109 	#define REG_TUNE_TX_PREEMP_AMP_TUNE_MASK	GENMASK(12, 11)
110 	#define REG_TUNE_TX_FSLS_TUNE_MASK		GENMASK(16, 13)
111 	#define REG_TUNE_SQRX_TUNE_MASK			GENMASK(19, 17)
112 	#define REG_TUNE_OTG_TUNE			GENMASK(22, 20)
113 	#define REG_TUNE_COMP_DIS_TUNE			GENMASK(25, 23)
114 	#define REG_TUNE_HOST_DM_PULLDOWN		BIT(26)
115 	#define REG_TUNE_HOST_DP_PULLDOWN		BIT(27)
116 
117 #define RESET_COMPLETE_TIME				500
118 #define ACA_ENABLE_COMPLETE_TIME			50
119 
120 struct phy_meson8b_usb2_match_data {
121 	bool			host_enable_aca;
122 };
123 
124 struct phy_meson8b_usb2_priv {
125 	struct regmap					*regmap;
126 	enum usb_dr_mode				dr_mode;
127 	struct clk					*clk_usb_general;
128 	struct clk					*clk_usb;
129 	struct reset_control				*reset;
130 	const struct phy_meson8b_usb2_match_data	*match;
131 };
132 
133 static const struct regmap_config phy_meson8b_usb2_regmap_conf = {
134 	.reg_bits = 8,
135 	.val_bits = 32,
136 	.reg_stride = 4,
137 	.max_register = REG_TUNE,
138 };
139 
140 static int phy_meson8b_usb2_power_on(struct phy *phy)
141 {
142 	struct phy_meson8b_usb2_priv *priv = phy_get_drvdata(phy);
143 	u32 reg;
144 	int ret;
145 
146 	if (!IS_ERR_OR_NULL(priv->reset)) {
147 		ret = reset_control_reset(priv->reset);
148 		if (ret) {
149 			dev_err(&phy->dev, "Failed to trigger USB reset\n");
150 			return ret;
151 		}
152 	}
153 
154 	ret = clk_prepare_enable(priv->clk_usb_general);
155 	if (ret) {
156 		dev_err(&phy->dev, "Failed to enable USB general clock\n");
157 		reset_control_rearm(priv->reset);
158 		return ret;
159 	}
160 
161 	ret = clk_prepare_enable(priv->clk_usb);
162 	if (ret) {
163 		dev_err(&phy->dev, "Failed to enable USB DDR clock\n");
164 		clk_disable_unprepare(priv->clk_usb_general);
165 		reset_control_rearm(priv->reset);
166 		return ret;
167 	}
168 
169 	regmap_update_bits(priv->regmap, REG_CONFIG, REG_CONFIG_CLK_32k_ALTSEL,
170 			   REG_CONFIG_CLK_32k_ALTSEL);
171 
172 	regmap_update_bits(priv->regmap, REG_CTRL, REG_CTRL_REF_CLK_SEL_MASK,
173 			   0x2 << REG_CTRL_REF_CLK_SEL_SHIFT);
174 
175 	regmap_update_bits(priv->regmap, REG_CTRL, REG_CTRL_FSEL_MASK,
176 			   0x5 << REG_CTRL_FSEL_SHIFT);
177 
178 	/* reset the PHY */
179 	regmap_update_bits(priv->regmap, REG_CTRL, REG_CTRL_POWER_ON_RESET,
180 			   REG_CTRL_POWER_ON_RESET);
181 	udelay(RESET_COMPLETE_TIME);
182 	regmap_update_bits(priv->regmap, REG_CTRL, REG_CTRL_POWER_ON_RESET, 0);
183 	udelay(RESET_COMPLETE_TIME);
184 
185 	regmap_update_bits(priv->regmap, REG_CTRL, REG_CTRL_SOF_TOGGLE_OUT,
186 			   REG_CTRL_SOF_TOGGLE_OUT);
187 
188 	if (priv->dr_mode == USB_DR_MODE_HOST) {
189 		regmap_update_bits(priv->regmap, REG_DBG_UART,
190 				   REG_DBG_UART_SET_IDDQ, 0);
191 
192 		if (priv->match->host_enable_aca) {
193 			regmap_update_bits(priv->regmap, REG_ADP_BC,
194 					   REG_ADP_BC_ACA_ENABLE,
195 					   REG_ADP_BC_ACA_ENABLE);
196 
197 			udelay(ACA_ENABLE_COMPLETE_TIME);
198 
199 			regmap_read(priv->regmap, REG_ADP_BC, &reg);
200 			if (reg & REG_ADP_BC_ACA_PIN_FLOAT) {
201 				dev_warn(&phy->dev, "USB ID detect failed!\n");
202 				clk_disable_unprepare(priv->clk_usb);
203 				clk_disable_unprepare(priv->clk_usb_general);
204 				reset_control_rearm(priv->reset);
205 				return -EINVAL;
206 			}
207 		}
208 	}
209 
210 	return 0;
211 }
212 
213 static int phy_meson8b_usb2_power_off(struct phy *phy)
214 {
215 	struct phy_meson8b_usb2_priv *priv = phy_get_drvdata(phy);
216 
217 	if (priv->dr_mode == USB_DR_MODE_HOST)
218 		regmap_update_bits(priv->regmap, REG_DBG_UART,
219 				   REG_DBG_UART_SET_IDDQ,
220 				   REG_DBG_UART_SET_IDDQ);
221 
222 	clk_disable_unprepare(priv->clk_usb);
223 	clk_disable_unprepare(priv->clk_usb_general);
224 	reset_control_rearm(priv->reset);
225 
226 	/* power off the PHY by putting it into reset mode */
227 	regmap_update_bits(priv->regmap, REG_CTRL, REG_CTRL_POWER_ON_RESET,
228 			   REG_CTRL_POWER_ON_RESET);
229 
230 	return 0;
231 }
232 
233 static const struct phy_ops phy_meson8b_usb2_ops = {
234 	.power_on	= phy_meson8b_usb2_power_on,
235 	.power_off	= phy_meson8b_usb2_power_off,
236 	.owner		= THIS_MODULE,
237 };
238 
239 static int phy_meson8b_usb2_probe(struct platform_device *pdev)
240 {
241 	struct phy_meson8b_usb2_priv *priv;
242 	struct phy *phy;
243 	struct phy_provider *phy_provider;
244 	void __iomem *base;
245 
246 	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
247 	if (!priv)
248 		return -ENOMEM;
249 
250 	base = devm_platform_ioremap_resource(pdev, 0);
251 	if (IS_ERR(base))
252 		return PTR_ERR(base);
253 
254 	priv->match = device_get_match_data(&pdev->dev);
255 	if (!priv->match)
256 		return -ENODEV;
257 
258 	priv->regmap = devm_regmap_init_mmio(&pdev->dev, base,
259 					     &phy_meson8b_usb2_regmap_conf);
260 	if (IS_ERR(priv->regmap))
261 		return PTR_ERR(priv->regmap);
262 
263 	priv->clk_usb_general = devm_clk_get(&pdev->dev, "usb_general");
264 	if (IS_ERR(priv->clk_usb_general))
265 		return PTR_ERR(priv->clk_usb_general);
266 
267 	priv->clk_usb = devm_clk_get(&pdev->dev, "usb");
268 	if (IS_ERR(priv->clk_usb))
269 		return PTR_ERR(priv->clk_usb);
270 
271 	priv->reset = devm_reset_control_get_optional_shared(&pdev->dev, NULL);
272 	if (IS_ERR(priv->reset))
273 		return dev_err_probe(&pdev->dev, PTR_ERR(priv->reset),
274 				     "Failed to get the reset line");
275 
276 	priv->dr_mode = of_usb_get_dr_mode_by_phy(pdev->dev.of_node, -1);
277 	if (priv->dr_mode == USB_DR_MODE_UNKNOWN) {
278 		dev_err(&pdev->dev,
279 			"missing dual role configuration of the controller\n");
280 		return -EINVAL;
281 	}
282 
283 	phy = devm_phy_create(&pdev->dev, NULL, &phy_meson8b_usb2_ops);
284 	if (IS_ERR(phy)) {
285 		return dev_err_probe(&pdev->dev, PTR_ERR(phy),
286 				     "failed to create PHY\n");
287 	}
288 
289 	phy_set_drvdata(phy, priv);
290 
291 	phy_provider =
292 		devm_of_phy_provider_register(&pdev->dev, of_phy_simple_xlate);
293 
294 	return PTR_ERR_OR_ZERO(phy_provider);
295 }
296 
297 static const struct phy_meson8b_usb2_match_data phy_meson8_usb2_match_data = {
298 	.host_enable_aca = false,
299 };
300 
301 static const struct phy_meson8b_usb2_match_data phy_meson8b_usb2_match_data = {
302 	.host_enable_aca = true,
303 };
304 
305 static const struct of_device_id phy_meson8b_usb2_of_match[] = {
306 	{
307 		.compatible = "amlogic,meson8-usb2-phy",
308 		.data = &phy_meson8_usb2_match_data
309 	},
310 	{
311 		.compatible = "amlogic,meson8b-usb2-phy",
312 		.data = &phy_meson8b_usb2_match_data
313 	},
314 	{
315 		.compatible = "amlogic,meson8m2-usb2-phy",
316 		.data = &phy_meson8b_usb2_match_data
317 	},
318 	{
319 		.compatible = "amlogic,meson-gxbb-usb2-phy",
320 		.data = &phy_meson8b_usb2_match_data
321 	},
322 	{ /* sentinel */ }
323 };
324 MODULE_DEVICE_TABLE(of, phy_meson8b_usb2_of_match);
325 
326 static struct platform_driver phy_meson8b_usb2_driver = {
327 	.probe	= phy_meson8b_usb2_probe,
328 	.driver	= {
329 		.name		= "phy-meson-usb2",
330 		.of_match_table	= phy_meson8b_usb2_of_match,
331 	},
332 };
333 module_platform_driver(phy_meson8b_usb2_driver);
334 
335 MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl@googlemail.com>");
336 MODULE_DESCRIPTION("Meson8, Meson8b, Meson8m2 and GXBB USB2 PHY driver");
337 MODULE_LICENSE("GPL");
338