1 // SPDX-License-Identifier: GPL-2.0-only 2 // Copyright (c) 2012-2017 ASPEED Technology Inc. 3 // Copyright (c) 2018-2021 Intel Corporation 4 5 #include <asm/unaligned.h> 6 7 #include <linux/bitfield.h> 8 #include <linux/clk.h> 9 #include <linux/clkdev.h> 10 #include <linux/clk-provider.h> 11 #include <linux/delay.h> 12 #include <linux/interrupt.h> 13 #include <linux/io.h> 14 #include <linux/iopoll.h> 15 #include <linux/jiffies.h> 16 #include <linux/math.h> 17 #include <linux/module.h> 18 #include <linux/of.h> 19 #include <linux/peci.h> 20 #include <linux/platform_device.h> 21 #include <linux/reset.h> 22 23 /* ASPEED PECI Registers */ 24 /* Control Register */ 25 #define ASPEED_PECI_CTRL 0x00 26 #define ASPEED_PECI_CTRL_SAMPLING_MASK GENMASK(19, 16) 27 #define ASPEED_PECI_CTRL_RD_MODE_MASK GENMASK(13, 12) 28 #define ASPEED_PECI_CTRL_RD_MODE_DBG BIT(13) 29 #define ASPEED_PECI_CTRL_RD_MODE_COUNT BIT(12) 30 #define ASPEED_PECI_CTRL_CLK_SRC_HCLK BIT(11) 31 #define ASPEED_PECI_CTRL_CLK_DIV_MASK GENMASK(10, 8) 32 #define ASPEED_PECI_CTRL_INVERT_OUT BIT(7) 33 #define ASPEED_PECI_CTRL_INVERT_IN BIT(6) 34 #define ASPEED_PECI_CTRL_BUS_CONTENTION_EN BIT(5) 35 #define ASPEED_PECI_CTRL_PECI_EN BIT(4) 36 #define ASPEED_PECI_CTRL_PECI_CLK_EN BIT(0) 37 38 /* Timing Negotiation Register */ 39 #define ASPEED_PECI_TIMING_NEGOTIATION 0x04 40 #define ASPEED_PECI_T_NEGO_MSG_MASK GENMASK(15, 8) 41 #define ASPEED_PECI_T_NEGO_ADDR_MASK GENMASK(7, 0) 42 43 /* Command Register */ 44 #define ASPEED_PECI_CMD 0x08 45 #define ASPEED_PECI_CMD_PIN_MONITORING BIT(31) 46 #define ASPEED_PECI_CMD_STS_MASK GENMASK(27, 24) 47 #define ASPEED_PECI_CMD_STS_ADDR_T_NEGO 0x3 48 #define ASPEED_PECI_CMD_IDLE_MASK \ 49 (ASPEED_PECI_CMD_STS_MASK | ASPEED_PECI_CMD_PIN_MONITORING) 50 #define ASPEED_PECI_CMD_FIRE BIT(0) 51 52 /* Read/Write Length Register */ 53 #define ASPEED_PECI_RW_LENGTH 0x0c 54 #define ASPEED_PECI_AW_FCS_EN BIT(31) 55 #define ASPEED_PECI_RD_LEN_MASK GENMASK(23, 16) 56 #define ASPEED_PECI_WR_LEN_MASK GENMASK(15, 8) 57 #define ASPEED_PECI_TARGET_ADDR_MASK GENMASK(7, 0) 58 59 /* Expected FCS Data Register */ 60 #define ASPEED_PECI_EXPECTED_FCS 0x10 61 #define ASPEED_PECI_EXPECTED_RD_FCS_MASK GENMASK(23, 16) 62 #define ASPEED_PECI_EXPECTED_AW_FCS_AUTO_MASK GENMASK(15, 8) 63 #define ASPEED_PECI_EXPECTED_WR_FCS_MASK GENMASK(7, 0) 64 65 /* Captured FCS Data Register */ 66 #define ASPEED_PECI_CAPTURED_FCS 0x14 67 #define ASPEED_PECI_CAPTURED_RD_FCS_MASK GENMASK(23, 16) 68 #define ASPEED_PECI_CAPTURED_WR_FCS_MASK GENMASK(7, 0) 69 70 /* Interrupt Register */ 71 #define ASPEED_PECI_INT_CTRL 0x18 72 #define ASPEED_PECI_TIMING_NEGO_SEL_MASK GENMASK(31, 30) 73 #define ASPEED_PECI_1ST_BIT_OF_ADDR_NEGO 0 74 #define ASPEED_PECI_2ND_BIT_OF_ADDR_NEGO 1 75 #define ASPEED_PECI_MESSAGE_NEGO 2 76 #define ASPEED_PECI_INT_MASK GENMASK(4, 0) 77 #define ASPEED_PECI_INT_BUS_TIMEOUT BIT(4) 78 #define ASPEED_PECI_INT_BUS_CONTENTION BIT(3) 79 #define ASPEED_PECI_INT_WR_FCS_BAD BIT(2) 80 #define ASPEED_PECI_INT_WR_FCS_ABORT BIT(1) 81 #define ASPEED_PECI_INT_CMD_DONE BIT(0) 82 83 /* Interrupt Status Register */ 84 #define ASPEED_PECI_INT_STS 0x1c 85 #define ASPEED_PECI_INT_TIMING_RESULT_MASK GENMASK(29, 16) 86 /* bits[4..0]: Same bit fields in the 'Interrupt Register' */ 87 88 /* Rx/Tx Data Buffer Registers */ 89 #define ASPEED_PECI_WR_DATA0 0x20 90 #define ASPEED_PECI_WR_DATA1 0x24 91 #define ASPEED_PECI_WR_DATA2 0x28 92 #define ASPEED_PECI_WR_DATA3 0x2c 93 #define ASPEED_PECI_RD_DATA0 0x30 94 #define ASPEED_PECI_RD_DATA1 0x34 95 #define ASPEED_PECI_RD_DATA2 0x38 96 #define ASPEED_PECI_RD_DATA3 0x3c 97 #define ASPEED_PECI_WR_DATA4 0x40 98 #define ASPEED_PECI_WR_DATA5 0x44 99 #define ASPEED_PECI_WR_DATA6 0x48 100 #define ASPEED_PECI_WR_DATA7 0x4c 101 #define ASPEED_PECI_RD_DATA4 0x50 102 #define ASPEED_PECI_RD_DATA5 0x54 103 #define ASPEED_PECI_RD_DATA6 0x58 104 #define ASPEED_PECI_RD_DATA7 0x5c 105 #define ASPEED_PECI_DATA_BUF_SIZE_MAX 32 106 107 /* Timing Negotiation */ 108 #define ASPEED_PECI_CLK_FREQUENCY_MIN 2000 109 #define ASPEED_PECI_CLK_FREQUENCY_DEFAULT 1000000 110 #define ASPEED_PECI_CLK_FREQUENCY_MAX 2000000 111 #define ASPEED_PECI_RD_SAMPLING_POINT_DEFAULT 8 112 /* Timeout */ 113 #define ASPEED_PECI_IDLE_CHECK_TIMEOUT_US (50 * USEC_PER_MSEC) 114 #define ASPEED_PECI_IDLE_CHECK_INTERVAL_US (10 * USEC_PER_MSEC) 115 #define ASPEED_PECI_CMD_TIMEOUT_MS_DEFAULT 1000 116 #define ASPEED_PECI_CMD_TIMEOUT_MS_MAX 1000 117 118 #define ASPEED_PECI_CLK_DIV1(msg_timing) (4 * (msg_timing) + 1) 119 #define ASPEED_PECI_CLK_DIV2(clk_div_exp) BIT(clk_div_exp) 120 #define ASPEED_PECI_CLK_DIV(msg_timing, clk_div_exp) \ 121 (4 * ASPEED_PECI_CLK_DIV1(msg_timing) * ASPEED_PECI_CLK_DIV2(clk_div_exp)) 122 123 struct aspeed_peci { 124 struct peci_controller *controller; 125 struct device *dev; 126 void __iomem *base; 127 struct reset_control *rst; 128 int irq; 129 spinlock_t lock; /* to sync completion status handling */ 130 struct completion xfer_complete; 131 struct clk *clk; 132 u32 clk_frequency; 133 u32 status; 134 u32 cmd_timeout_ms; 135 }; 136 137 struct clk_aspeed_peci { 138 struct clk_hw hw; 139 struct aspeed_peci *aspeed_peci; 140 }; 141 142 static void aspeed_peci_controller_enable(struct aspeed_peci *priv) 143 { 144 u32 val = readl(priv->base + ASPEED_PECI_CTRL); 145 146 val |= ASPEED_PECI_CTRL_PECI_CLK_EN; 147 val |= ASPEED_PECI_CTRL_PECI_EN; 148 149 writel(val, priv->base + ASPEED_PECI_CTRL); 150 } 151 152 static void aspeed_peci_init_regs(struct aspeed_peci *priv) 153 { 154 u32 val; 155 156 /* Clear interrupts */ 157 writel(ASPEED_PECI_INT_MASK, priv->base + ASPEED_PECI_INT_STS); 158 159 /* Set timing negotiation mode and enable interrupts */ 160 val = FIELD_PREP(ASPEED_PECI_TIMING_NEGO_SEL_MASK, ASPEED_PECI_1ST_BIT_OF_ADDR_NEGO); 161 val |= ASPEED_PECI_INT_MASK; 162 writel(val, priv->base + ASPEED_PECI_INT_CTRL); 163 164 val = FIELD_PREP(ASPEED_PECI_CTRL_SAMPLING_MASK, ASPEED_PECI_RD_SAMPLING_POINT_DEFAULT); 165 writel(val, priv->base + ASPEED_PECI_CTRL); 166 } 167 168 static int aspeed_peci_check_idle(struct aspeed_peci *priv) 169 { 170 u32 cmd_sts = readl(priv->base + ASPEED_PECI_CMD); 171 int ret; 172 173 /* 174 * Under normal circumstances, we expect to be idle here. 175 * In case there were any errors/timeouts that led to the situation 176 * where the hardware is not in idle state - we need to reset and 177 * reinitialize it to avoid potential controller hang. 178 */ 179 if (FIELD_GET(ASPEED_PECI_CMD_STS_MASK, cmd_sts)) { 180 ret = reset_control_assert(priv->rst); 181 if (ret) { 182 dev_err(priv->dev, "cannot assert reset control\n"); 183 return ret; 184 } 185 186 ret = reset_control_deassert(priv->rst); 187 if (ret) { 188 dev_err(priv->dev, "cannot deassert reset control\n"); 189 return ret; 190 } 191 192 aspeed_peci_init_regs(priv); 193 194 ret = clk_set_rate(priv->clk, priv->clk_frequency); 195 if (ret < 0) { 196 dev_err(priv->dev, "cannot set clock frequency\n"); 197 return ret; 198 } 199 200 aspeed_peci_controller_enable(priv); 201 } 202 203 return readl_poll_timeout(priv->base + ASPEED_PECI_CMD, 204 cmd_sts, 205 !(cmd_sts & ASPEED_PECI_CMD_IDLE_MASK), 206 ASPEED_PECI_IDLE_CHECK_INTERVAL_US, 207 ASPEED_PECI_IDLE_CHECK_TIMEOUT_US); 208 } 209 210 static int aspeed_peci_xfer(struct peci_controller *controller, 211 u8 addr, struct peci_request *req) 212 { 213 struct aspeed_peci *priv = dev_get_drvdata(controller->dev.parent); 214 unsigned long timeout = msecs_to_jiffies(priv->cmd_timeout_ms); 215 u32 peci_head; 216 int ret, i; 217 218 if (req->tx.len > ASPEED_PECI_DATA_BUF_SIZE_MAX || 219 req->rx.len > ASPEED_PECI_DATA_BUF_SIZE_MAX) 220 return -EINVAL; 221 222 /* Check command sts and bus idle state */ 223 ret = aspeed_peci_check_idle(priv); 224 if (ret) 225 return ret; /* -ETIMEDOUT */ 226 227 spin_lock_irq(&priv->lock); 228 reinit_completion(&priv->xfer_complete); 229 230 peci_head = FIELD_PREP(ASPEED_PECI_TARGET_ADDR_MASK, addr) | 231 FIELD_PREP(ASPEED_PECI_WR_LEN_MASK, req->tx.len) | 232 FIELD_PREP(ASPEED_PECI_RD_LEN_MASK, req->rx.len); 233 234 writel(peci_head, priv->base + ASPEED_PECI_RW_LENGTH); 235 236 for (i = 0; i < req->tx.len; i += 4) { 237 u32 reg = (i < 16 ? ASPEED_PECI_WR_DATA0 : ASPEED_PECI_WR_DATA4) + i % 16; 238 239 writel(get_unaligned_le32(&req->tx.buf[i]), priv->base + reg); 240 } 241 242 #if IS_ENABLED(CONFIG_DYNAMIC_DEBUG) 243 dev_dbg(priv->dev, "HEAD : %#08x\n", peci_head); 244 print_hex_dump_bytes("TX : ", DUMP_PREFIX_NONE, req->tx.buf, req->tx.len); 245 #endif 246 247 priv->status = 0; 248 writel(ASPEED_PECI_CMD_FIRE, priv->base + ASPEED_PECI_CMD); 249 spin_unlock_irq(&priv->lock); 250 251 ret = wait_for_completion_interruptible_timeout(&priv->xfer_complete, timeout); 252 if (ret < 0) 253 return ret; 254 255 if (ret == 0) { 256 dev_dbg(priv->dev, "timeout waiting for a response\n"); 257 return -ETIMEDOUT; 258 } 259 260 spin_lock_irq(&priv->lock); 261 262 if (priv->status != ASPEED_PECI_INT_CMD_DONE) { 263 spin_unlock_irq(&priv->lock); 264 dev_dbg(priv->dev, "no valid response, status: %#02x\n", priv->status); 265 return -EIO; 266 } 267 268 spin_unlock_irq(&priv->lock); 269 270 /* 271 * We need to use dword reads for register access, make sure that the 272 * buffer size is multiple of 4-bytes. 273 */ 274 BUILD_BUG_ON(PECI_REQUEST_MAX_BUF_SIZE % 4); 275 276 for (i = 0; i < req->rx.len; i += 4) { 277 u32 reg = (i < 16 ? ASPEED_PECI_RD_DATA0 : ASPEED_PECI_RD_DATA4) + i % 16; 278 u32 rx_data = readl(priv->base + reg); 279 280 put_unaligned_le32(rx_data, &req->rx.buf[i]); 281 } 282 283 #if IS_ENABLED(CONFIG_DYNAMIC_DEBUG) 284 print_hex_dump_bytes("RX : ", DUMP_PREFIX_NONE, req->rx.buf, req->rx.len); 285 #endif 286 return 0; 287 } 288 289 static irqreturn_t aspeed_peci_irq_handler(int irq, void *arg) 290 { 291 struct aspeed_peci *priv = arg; 292 u32 status; 293 294 spin_lock(&priv->lock); 295 status = readl(priv->base + ASPEED_PECI_INT_STS); 296 writel(status, priv->base + ASPEED_PECI_INT_STS); 297 priv->status |= (status & ASPEED_PECI_INT_MASK); 298 299 /* 300 * All commands should be ended up with a ASPEED_PECI_INT_CMD_DONE bit 301 * set even in an error case. 302 */ 303 if (status & ASPEED_PECI_INT_CMD_DONE) 304 complete(&priv->xfer_complete); 305 306 writel(0, priv->base + ASPEED_PECI_CMD); 307 308 spin_unlock(&priv->lock); 309 310 return IRQ_HANDLED; 311 } 312 313 static void clk_aspeed_peci_find_div_values(unsigned long rate, int *msg_timing, int *clk_div_exp) 314 { 315 unsigned long best_diff = ~0ul, diff; 316 int msg_timing_temp, clk_div_exp_temp, i, j; 317 318 for (i = 1; i <= 255; i++) 319 for (j = 0; j < 8; j++) { 320 diff = abs(rate - ASPEED_PECI_CLK_DIV1(i) * ASPEED_PECI_CLK_DIV2(j)); 321 if (diff < best_diff) { 322 msg_timing_temp = i; 323 clk_div_exp_temp = j; 324 best_diff = diff; 325 } 326 } 327 328 *msg_timing = msg_timing_temp; 329 *clk_div_exp = clk_div_exp_temp; 330 } 331 332 static int clk_aspeed_peci_get_div(unsigned long rate, const unsigned long *prate) 333 { 334 unsigned long this_rate = *prate / (4 * rate); 335 int msg_timing, clk_div_exp; 336 337 clk_aspeed_peci_find_div_values(this_rate, &msg_timing, &clk_div_exp); 338 339 return ASPEED_PECI_CLK_DIV(msg_timing, clk_div_exp); 340 } 341 342 static int clk_aspeed_peci_set_rate(struct clk_hw *hw, unsigned long rate, 343 unsigned long prate) 344 { 345 struct clk_aspeed_peci *peci_clk = container_of(hw, struct clk_aspeed_peci, hw); 346 struct aspeed_peci *aspeed_peci = peci_clk->aspeed_peci; 347 unsigned long this_rate = prate / (4 * rate); 348 int clk_div_exp, msg_timing; 349 u32 val; 350 351 clk_aspeed_peci_find_div_values(this_rate, &msg_timing, &clk_div_exp); 352 353 val = readl(aspeed_peci->base + ASPEED_PECI_CTRL); 354 val |= FIELD_PREP(ASPEED_PECI_CTRL_CLK_DIV_MASK, clk_div_exp); 355 writel(val, aspeed_peci->base + ASPEED_PECI_CTRL); 356 357 val = FIELD_PREP(ASPEED_PECI_T_NEGO_MSG_MASK, msg_timing); 358 val |= FIELD_PREP(ASPEED_PECI_T_NEGO_ADDR_MASK, msg_timing); 359 writel(val, aspeed_peci->base + ASPEED_PECI_TIMING_NEGOTIATION); 360 361 return 0; 362 } 363 364 static long clk_aspeed_peci_round_rate(struct clk_hw *hw, unsigned long rate, 365 unsigned long *prate) 366 { 367 int div = clk_aspeed_peci_get_div(rate, prate); 368 369 return DIV_ROUND_UP_ULL(*prate, div); 370 } 371 372 static unsigned long clk_aspeed_peci_recalc_rate(struct clk_hw *hw, unsigned long prate) 373 { 374 struct clk_aspeed_peci *peci_clk = container_of(hw, struct clk_aspeed_peci, hw); 375 struct aspeed_peci *aspeed_peci = peci_clk->aspeed_peci; 376 int div, msg_timing, addr_timing, clk_div_exp; 377 u32 reg; 378 379 reg = readl(aspeed_peci->base + ASPEED_PECI_TIMING_NEGOTIATION); 380 msg_timing = FIELD_GET(ASPEED_PECI_T_NEGO_MSG_MASK, reg); 381 addr_timing = FIELD_GET(ASPEED_PECI_T_NEGO_ADDR_MASK, reg); 382 383 if (msg_timing != addr_timing) 384 return 0; 385 386 reg = readl(aspeed_peci->base + ASPEED_PECI_CTRL); 387 clk_div_exp = FIELD_GET(ASPEED_PECI_CTRL_CLK_DIV_MASK, reg); 388 389 div = ASPEED_PECI_CLK_DIV(msg_timing, clk_div_exp); 390 391 return DIV_ROUND_UP_ULL(prate, div); 392 } 393 394 static const struct clk_ops clk_aspeed_peci_ops = { 395 .set_rate = clk_aspeed_peci_set_rate, 396 .round_rate = clk_aspeed_peci_round_rate, 397 .recalc_rate = clk_aspeed_peci_recalc_rate, 398 }; 399 400 /* 401 * PECI HW contains a clock divider which is a combination of: 402 * div0: 4 (fixed divider) 403 * div1: x + 1 404 * div2: 1 << y 405 * In other words, out_clk = in_clk / (div0 * div1 * div2) 406 * The resulting frequency is used by PECI Controller to drive the PECI bus to 407 * negotiate optimal transfer rate. 408 */ 409 static struct clk *devm_aspeed_peci_register_clk_div(struct device *dev, struct clk *parent, 410 struct aspeed_peci *priv) 411 { 412 struct clk_aspeed_peci *peci_clk; 413 struct clk_init_data init; 414 const char *parent_name; 415 char name[32]; 416 int ret; 417 418 snprintf(name, sizeof(name), "%s_div", dev_name(dev)); 419 420 parent_name = __clk_get_name(parent); 421 422 init.ops = &clk_aspeed_peci_ops; 423 init.name = name; 424 init.parent_names = (const char* []) { parent_name }; 425 init.num_parents = 1; 426 init.flags = 0; 427 428 peci_clk = devm_kzalloc(dev, sizeof(struct clk_aspeed_peci), GFP_KERNEL); 429 if (!peci_clk) 430 return ERR_PTR(-ENOMEM); 431 432 peci_clk->hw.init = &init; 433 peci_clk->aspeed_peci = priv; 434 435 ret = devm_clk_hw_register(dev, &peci_clk->hw); 436 if (ret) 437 return ERR_PTR(ret); 438 439 return peci_clk->hw.clk; 440 } 441 442 static void aspeed_peci_property_sanitize(struct device *dev, const char *propname, 443 u32 min, u32 max, u32 default_val, u32 *propval) 444 { 445 u32 val; 446 int ret; 447 448 ret = device_property_read_u32(dev, propname, &val); 449 if (ret) { 450 val = default_val; 451 } else if (val > max || val < min) { 452 dev_warn(dev, "invalid %s: %u, falling back to: %u\n", 453 propname, val, default_val); 454 455 val = default_val; 456 } 457 458 *propval = val; 459 } 460 461 static void aspeed_peci_property_setup(struct aspeed_peci *priv) 462 { 463 aspeed_peci_property_sanitize(priv->dev, "clock-frequency", 464 ASPEED_PECI_CLK_FREQUENCY_MIN, ASPEED_PECI_CLK_FREQUENCY_MAX, 465 ASPEED_PECI_CLK_FREQUENCY_DEFAULT, &priv->clk_frequency); 466 aspeed_peci_property_sanitize(priv->dev, "cmd-timeout-ms", 467 1, ASPEED_PECI_CMD_TIMEOUT_MS_MAX, 468 ASPEED_PECI_CMD_TIMEOUT_MS_DEFAULT, &priv->cmd_timeout_ms); 469 } 470 471 static struct peci_controller_ops aspeed_ops = { 472 .xfer = aspeed_peci_xfer, 473 }; 474 475 static void aspeed_peci_reset_control_release(void *data) 476 { 477 reset_control_assert(data); 478 } 479 480 static int devm_aspeed_peci_reset_control_deassert(struct device *dev, struct reset_control *rst) 481 { 482 int ret; 483 484 ret = reset_control_deassert(rst); 485 if (ret) 486 return ret; 487 488 return devm_add_action_or_reset(dev, aspeed_peci_reset_control_release, rst); 489 } 490 491 static void aspeed_peci_clk_release(void *data) 492 { 493 clk_disable_unprepare(data); 494 } 495 496 static int devm_aspeed_peci_clk_enable(struct device *dev, struct clk *clk) 497 { 498 int ret; 499 500 ret = clk_prepare_enable(clk); 501 if (ret) 502 return ret; 503 504 return devm_add_action_or_reset(dev, aspeed_peci_clk_release, clk); 505 } 506 507 static int aspeed_peci_probe(struct platform_device *pdev) 508 { 509 struct peci_controller *controller; 510 struct aspeed_peci *priv; 511 struct clk *ref_clk; 512 int ret; 513 514 priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); 515 if (!priv) 516 return -ENOMEM; 517 518 priv->dev = &pdev->dev; 519 dev_set_drvdata(priv->dev, priv); 520 521 priv->base = devm_platform_ioremap_resource(pdev, 0); 522 if (IS_ERR(priv->base)) 523 return PTR_ERR(priv->base); 524 525 priv->irq = platform_get_irq(pdev, 0); 526 if (!priv->irq) 527 return priv->irq; 528 529 ret = devm_request_irq(&pdev->dev, priv->irq, aspeed_peci_irq_handler, 530 0, "peci-aspeed", priv); 531 if (ret) 532 return ret; 533 534 init_completion(&priv->xfer_complete); 535 spin_lock_init(&priv->lock); 536 537 priv->rst = devm_reset_control_get(&pdev->dev, NULL); 538 if (IS_ERR(priv->rst)) 539 return dev_err_probe(priv->dev, PTR_ERR(priv->rst), 540 "failed to get reset control\n"); 541 542 ret = devm_aspeed_peci_reset_control_deassert(priv->dev, priv->rst); 543 if (ret) 544 return dev_err_probe(priv->dev, ret, "cannot deassert reset control\n"); 545 546 aspeed_peci_property_setup(priv); 547 548 aspeed_peci_init_regs(priv); 549 550 ref_clk = devm_clk_get(priv->dev, NULL); 551 if (IS_ERR(ref_clk)) 552 return dev_err_probe(priv->dev, PTR_ERR(ref_clk), "failed to get ref clock\n"); 553 554 priv->clk = devm_aspeed_peci_register_clk_div(priv->dev, ref_clk, priv); 555 if (IS_ERR(priv->clk)) 556 return dev_err_probe(priv->dev, PTR_ERR(priv->clk), "cannot register clock\n"); 557 558 ret = clk_set_rate(priv->clk, priv->clk_frequency); 559 if (ret < 0) 560 return dev_err_probe(priv->dev, ret, "cannot set clock frequency\n"); 561 562 ret = devm_aspeed_peci_clk_enable(priv->dev, priv->clk); 563 if (ret) 564 return dev_err_probe(priv->dev, ret, "failed to enable clock\n"); 565 566 aspeed_peci_controller_enable(priv); 567 568 controller = devm_peci_controller_add(priv->dev, &aspeed_ops); 569 if (IS_ERR(controller)) 570 return dev_err_probe(priv->dev, PTR_ERR(controller), 571 "failed to add aspeed peci controller\n"); 572 573 priv->controller = controller; 574 575 return 0; 576 } 577 578 static const struct of_device_id aspeed_peci_of_table[] = { 579 { .compatible = "aspeed,ast2400-peci", }, 580 { .compatible = "aspeed,ast2500-peci", }, 581 { .compatible = "aspeed,ast2600-peci", }, 582 { } 583 }; 584 MODULE_DEVICE_TABLE(of, aspeed_peci_of_table); 585 586 static struct platform_driver aspeed_peci_driver = { 587 .probe = aspeed_peci_probe, 588 .driver = { 589 .name = "peci-aspeed", 590 .of_match_table = aspeed_peci_of_table, 591 }, 592 }; 593 module_platform_driver(aspeed_peci_driver); 594 595 MODULE_AUTHOR("Ryan Chen <ryan_chen@aspeedtech.com>"); 596 MODULE_AUTHOR("Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>"); 597 MODULE_DESCRIPTION("ASPEED PECI driver"); 598 MODULE_LICENSE("GPL"); 599 MODULE_IMPORT_NS(PECI); 600