1 /*======================================================================
2 
3     Device driver for the PCMCIA control functionality of StrongARM
4     SA-1100 microprocessors.
5 
6     The contents of this file are subject to the Mozilla Public
7     License Version 1.1 (the "License"); you may not use this file
8     except in compliance with the License. You may obtain a copy of
9     the License at http://www.mozilla.org/MPL/
10 
11     Software distributed under the License is distributed on an "AS
12     IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or
13     implied. See the License for the specific language governing
14     rights and limitations under the License.
15 
16     The initial developer of the original code is John G. Dorsey
17     <john+@cs.cmu.edu>.  Portions created by John G. Dorsey are
18     Copyright (C) 1999 John G. Dorsey.  All Rights Reserved.
19 
20     Alternatively, the contents of this file may be used under the
21     terms of the GNU Public License version 2 (the "GPL"), in which
22     case the provisions of the GPL are applicable instead of the
23     above.  If you wish to allow the use of your version of this file
24     only under the terms of the GPL and not to allow others to use
25     your version of this file under the MPL, indicate your decision
26     by deleting the provisions above and replace them with the notice
27     and other provisions required by the GPL.  If you do not delete
28     the provisions above, a recipient may use your version of this
29     file under either the MPL or the GPL.
30 
31 ======================================================================*/
32 
33 #include <linux/module.h>
34 #include <linux/init.h>
35 #include <linux/slab.h>
36 #include <linux/platform_device.h>
37 
38 #include <pcmcia/ss.h>
39 
40 #include <asm/hardware/scoop.h>
41 
42 #include "sa1100_generic.h"
43 
44 int __init pcmcia_collie_init(struct device *dev);
45 
46 static int (*sa11x0_pcmcia_hw_init[])(struct device *dev) = {
47 #ifdef CONFIG_SA1100_ASSABET
48 	pcmcia_assabet_init,
49 #endif
50 #ifdef CONFIG_SA1100_CERF
51 	pcmcia_cerf_init,
52 #endif
53 #if defined(CONFIG_SA1100_H3100) || defined(CONFIG_SA1100_H3600)
54 	pcmcia_h3600_init,
55 #endif
56 #ifdef CONFIG_SA1100_NANOENGINE
57 	pcmcia_nanoengine_init,
58 #endif
59 #ifdef CONFIG_SA1100_SHANNON
60 	pcmcia_shannon_init,
61 #endif
62 #ifdef CONFIG_SA1100_SIMPAD
63 	pcmcia_simpad_init,
64 #endif
65 #ifdef CONFIG_SA1100_COLLIE
66        pcmcia_collie_init,
67 #endif
68 };
69 
70 static int sa11x0_drv_pcmcia_probe(struct platform_device *dev)
71 {
72 	int i, ret = -ENODEV;
73 
74 	/*
75 	 * Initialise any "on-board" PCMCIA sockets.
76 	 */
77 	for (i = 0; i < ARRAY_SIZE(sa11x0_pcmcia_hw_init); i++) {
78 		ret = sa11x0_pcmcia_hw_init[i](&dev->dev);
79 		if (ret == 0)
80 			break;
81 	}
82 
83 	return ret;
84 }
85 
86 static int sa11x0_drv_pcmcia_remove(struct platform_device *dev)
87 {
88 	struct skt_dev_info *sinfo = platform_get_drvdata(dev);
89 	int i;
90 
91 	platform_set_drvdata(dev, NULL);
92 
93 	for (i = 0; i < sinfo->nskt; i++)
94 		soc_pcmcia_remove_one(&sinfo->skt[i]);
95 
96 	kfree(sinfo);
97 	return 0;
98 }
99 
100 static struct platform_driver sa11x0_pcmcia_driver = {
101 	.driver = {
102 		.name		= "sa11x0-pcmcia",
103 		.owner		= THIS_MODULE,
104 	},
105 	.probe		= sa11x0_drv_pcmcia_probe,
106 	.remove		= sa11x0_drv_pcmcia_remove,
107 };
108 
109 /* sa11x0_pcmcia_init()
110  * ^^^^^^^^^^^^^^^^^^^^
111  *
112  * This routine performs low-level PCMCIA initialization and then
113  * registers this socket driver with Card Services.
114  *
115  * Returns: 0 on success, -ve error code on failure
116  */
117 static int __init sa11x0_pcmcia_init(void)
118 {
119 	return platform_driver_register(&sa11x0_pcmcia_driver);
120 }
121 
122 /* sa11x0_pcmcia_exit()
123  * ^^^^^^^^^^^^^^^^^^^^
124  * Invokes the low-level kernel service to free IRQs associated with this
125  * socket controller and reset GPIO edge detection.
126  */
127 static void __exit sa11x0_pcmcia_exit(void)
128 {
129 	platform_driver_unregister(&sa11x0_pcmcia_driver);
130 }
131 
132 MODULE_AUTHOR("John Dorsey <john+@cs.cmu.edu>");
133 MODULE_DESCRIPTION("Linux PCMCIA Card Services: SA-11x0 Socket Controller");
134 MODULE_LICENSE("Dual MPL/GPL");
135 
136 fs_initcall(sa11x0_pcmcia_init);
137 module_exit(sa11x0_pcmcia_exit);
138