1 // SPDX-License-Identifier: GPL-2.0-only 2 /* Low-level parallel-port routines for 8255-based PC-style hardware. 3 * 4 * Authors: Phil Blundell <philb@gnu.org> 5 * Tim Waugh <tim@cyberelk.demon.co.uk> 6 * Jose Renau <renau@acm.org> 7 * David Campbell 8 * Andrea Arcangeli 9 * 10 * based on work by Grant Guenther <grant@torque.net> and Phil Blundell. 11 * 12 * Cleaned up include files - Russell King <linux@arm.uk.linux.org> 13 * DMA support - Bert De Jonghe <bert@sophis.be> 14 * Many ECP bugs fixed. Fred Barnes & Jamie Lokier, 1999 15 * More PCI support now conditional on CONFIG_PCI, 03/2001, Paul G. 16 * Various hacks, Fred Barnes, 04/2001 17 * Updated probing logic - Adam Belay <ambx1@neo.rr.com> 18 */ 19 20 /* This driver should work with any hardware that is broadly compatible 21 * with that in the IBM PC. This applies to the majority of integrated 22 * I/O chipsets that are commonly available. The expected register 23 * layout is: 24 * 25 * base+0 data 26 * base+1 status 27 * base+2 control 28 * 29 * In addition, there are some optional registers: 30 * 31 * base+3 EPP address 32 * base+4 EPP data 33 * base+0x400 ECP config A 34 * base+0x401 ECP config B 35 * base+0x402 ECP control 36 * 37 * All registers are 8 bits wide and read/write. If your hardware differs 38 * only in register addresses (eg because your registers are on 32-bit 39 * word boundaries) then you can alter the constants in parport_pc.h to 40 * accommodate this. 41 * 42 * Note that the ECP registers may not start at offset 0x400 for PCI cards, 43 * but rather will start at port->base_hi. 44 */ 45 46 #include <linux/module.h> 47 #include <linux/init.h> 48 #include <linux/sched/signal.h> 49 #include <linux/delay.h> 50 #include <linux/errno.h> 51 #include <linux/interrupt.h> 52 #include <linux/ioport.h> 53 #include <linux/kernel.h> 54 #include <linux/slab.h> 55 #include <linux/dma-mapping.h> 56 #include <linux/pci.h> 57 #include <linux/pnp.h> 58 #include <linux/platform_device.h> 59 #include <linux/sysctl.h> 60 #include <linux/io.h> 61 #include <linux/uaccess.h> 62 63 #include <asm/dma.h> 64 65 #include <linux/parport.h> 66 #include <linux/parport_pc.h> 67 #include <linux/via.h> 68 #include <asm/parport.h> 69 70 #define PARPORT_PC_MAX_PORTS PARPORT_MAX 71 72 #ifdef CONFIG_ISA_DMA_API 73 #define HAS_DMA 74 #endif 75 76 /* ECR modes */ 77 #define ECR_SPP 00 78 #define ECR_PS2 01 79 #define ECR_PPF 02 80 #define ECR_ECP 03 81 #define ECR_EPP 04 82 #define ECR_VND 05 83 #define ECR_TST 06 84 #define ECR_CNF 07 85 #define ECR_MODE_MASK 0xe0 86 #define ECR_WRITE(p, v) frob_econtrol((p), 0xff, (v)) 87 88 #undef DEBUG 89 90 #define NR_SUPERIOS 3 91 static struct superio_struct { /* For Super-IO chips autodetection */ 92 int io; 93 int irq; 94 int dma; 95 } superios[NR_SUPERIOS] = { {0,},}; 96 97 static int user_specified; 98 #if defined(CONFIG_PARPORT_PC_SUPERIO) || \ 99 (defined(CONFIG_PARPORT_1284) && defined(CONFIG_PARPORT_PC_FIFO)) 100 static int verbose_probing; 101 #endif 102 static int pci_registered_parport; 103 static int pnp_registered_parport; 104 105 /* frob_control, but for ECR */ 106 static void frob_econtrol(struct parport *pb, unsigned char m, 107 unsigned char v) 108 { 109 unsigned char ectr = 0; 110 111 if (m != 0xff) 112 ectr = inb(ECONTROL(pb)); 113 114 pr_debug("frob_econtrol(%02x,%02x): %02x -> %02x\n", 115 m, v, ectr, (ectr & ~m) ^ v); 116 117 outb((ectr & ~m) ^ v, ECONTROL(pb)); 118 } 119 120 static inline void frob_set_mode(struct parport *p, int mode) 121 { 122 frob_econtrol(p, ECR_MODE_MASK, mode << 5); 123 } 124 125 #ifdef CONFIG_PARPORT_PC_FIFO 126 /* Safely change the mode bits in the ECR 127 Returns: 128 0 : Success 129 -EBUSY: Could not drain FIFO in some finite amount of time, 130 mode not changed! 131 */ 132 static int change_mode(struct parport *p, int m) 133 { 134 const struct parport_pc_private *priv = p->physport->private_data; 135 unsigned char oecr; 136 int mode; 137 138 pr_debug("parport change_mode ECP-ISA to mode 0x%02x\n", m); 139 140 if (!priv->ecr) { 141 printk(KERN_DEBUG "change_mode: but there's no ECR!\n"); 142 return 0; 143 } 144 145 /* Bits <7:5> contain the mode. */ 146 oecr = inb(ECONTROL(p)); 147 mode = (oecr >> 5) & 0x7; 148 if (mode == m) 149 return 0; 150 151 if (mode >= 2 && !(priv->ctr & 0x20)) { 152 /* This mode resets the FIFO, so we may 153 * have to wait for it to drain first. */ 154 unsigned long expire = jiffies + p->physport->cad->timeout; 155 int counter; 156 switch (mode) { 157 case ECR_PPF: /* Parallel Port FIFO mode */ 158 case ECR_ECP: /* ECP Parallel Port mode */ 159 /* Busy wait for 200us */ 160 for (counter = 0; counter < 40; counter++) { 161 if (inb(ECONTROL(p)) & 0x01) 162 break; 163 if (signal_pending(current)) 164 break; 165 udelay(5); 166 } 167 168 /* Poll slowly. */ 169 while (!(inb(ECONTROL(p)) & 0x01)) { 170 if (time_after_eq(jiffies, expire)) 171 /* The FIFO is stuck. */ 172 return -EBUSY; 173 schedule_timeout_interruptible( 174 msecs_to_jiffies(10)); 175 if (signal_pending(current)) 176 break; 177 } 178 } 179 } 180 181 if (mode >= 2 && m >= 2) { 182 /* We have to go through mode 001 */ 183 oecr &= ~(7 << 5); 184 oecr |= ECR_PS2 << 5; 185 ECR_WRITE(p, oecr); 186 } 187 188 /* Set the mode. */ 189 oecr &= ~(7 << 5); 190 oecr |= m << 5; 191 ECR_WRITE(p, oecr); 192 return 0; 193 } 194 #endif /* FIFO support */ 195 196 /* 197 * Clear TIMEOUT BIT in EPP MODE 198 * 199 * This is also used in SPP detection. 200 */ 201 static int clear_epp_timeout(struct parport *pb) 202 { 203 unsigned char r; 204 205 if (!(parport_pc_read_status(pb) & 0x01)) 206 return 1; 207 208 /* To clear timeout some chips require double read */ 209 parport_pc_read_status(pb); 210 r = parport_pc_read_status(pb); 211 outb(r | 0x01, STATUS(pb)); /* Some reset by writing 1 */ 212 outb(r & 0xfe, STATUS(pb)); /* Others by writing 0 */ 213 r = parport_pc_read_status(pb); 214 215 return !(r & 0x01); 216 } 217 218 /* 219 * Access functions. 220 * 221 * Most of these aren't static because they may be used by the 222 * parport_xxx_yyy macros. extern __inline__ versions of several 223 * of these are in parport_pc.h. 224 */ 225 226 static void parport_pc_init_state(struct pardevice *dev, 227 struct parport_state *s) 228 { 229 s->u.pc.ctr = 0xc; 230 if (dev->irq_func && 231 dev->port->irq != PARPORT_IRQ_NONE) 232 /* Set ackIntEn */ 233 s->u.pc.ctr |= 0x10; 234 235 s->u.pc.ecr = 0x34; /* NetMos chip can cause problems 0x24; 236 * D.Gruszka VScom */ 237 } 238 239 static void parport_pc_save_state(struct parport *p, struct parport_state *s) 240 { 241 const struct parport_pc_private *priv = p->physport->private_data; 242 s->u.pc.ctr = priv->ctr; 243 if (priv->ecr) 244 s->u.pc.ecr = inb(ECONTROL(p)); 245 } 246 247 static void parport_pc_restore_state(struct parport *p, 248 struct parport_state *s) 249 { 250 struct parport_pc_private *priv = p->physport->private_data; 251 register unsigned char c = s->u.pc.ctr & priv->ctr_writable; 252 outb(c, CONTROL(p)); 253 priv->ctr = c; 254 if (priv->ecr) 255 ECR_WRITE(p, s->u.pc.ecr); 256 } 257 258 #ifdef CONFIG_PARPORT_1284 259 static size_t parport_pc_epp_read_data(struct parport *port, void *buf, 260 size_t length, int flags) 261 { 262 size_t got = 0; 263 264 if (flags & PARPORT_W91284PIC) { 265 unsigned char status; 266 size_t left = length; 267 268 /* use knowledge about data lines..: 269 * nFault is 0 if there is at least 1 byte in the Warp's FIFO 270 * pError is 1 if there are 16 bytes in the Warp's FIFO 271 */ 272 status = inb(STATUS(port)); 273 274 while (!(status & 0x08) && got < length) { 275 if (left >= 16 && (status & 0x20) && !(status & 0x08)) { 276 /* can grab 16 bytes from warp fifo */ 277 if (!((long)buf & 0x03)) 278 insl(EPPDATA(port), buf, 4); 279 else 280 insb(EPPDATA(port), buf, 16); 281 buf += 16; 282 got += 16; 283 left -= 16; 284 } else { 285 /* grab single byte from the warp fifo */ 286 *((char *)buf) = inb(EPPDATA(port)); 287 buf++; 288 got++; 289 left--; 290 } 291 status = inb(STATUS(port)); 292 if (status & 0x01) { 293 /* EPP timeout should never occur... */ 294 printk(KERN_DEBUG "%s: EPP timeout occurred while talking to w91284pic (should not have done)\n", 295 port->name); 296 clear_epp_timeout(port); 297 } 298 } 299 return got; 300 } 301 if ((flags & PARPORT_EPP_FAST) && (length > 1)) { 302 if (!(((long)buf | length) & 0x03)) 303 insl(EPPDATA(port), buf, (length >> 2)); 304 else 305 insb(EPPDATA(port), buf, length); 306 if (inb(STATUS(port)) & 0x01) { 307 clear_epp_timeout(port); 308 return -EIO; 309 } 310 return length; 311 } 312 for (; got < length; got++) { 313 *((char *)buf) = inb(EPPDATA(port)); 314 buf++; 315 if (inb(STATUS(port)) & 0x01) { 316 /* EPP timeout */ 317 clear_epp_timeout(port); 318 break; 319 } 320 } 321 322 return got; 323 } 324 325 static size_t parport_pc_epp_write_data(struct parport *port, const void *buf, 326 size_t length, int flags) 327 { 328 size_t written = 0; 329 330 if ((flags & PARPORT_EPP_FAST) && (length > 1)) { 331 if (!(((long)buf | length) & 0x03)) 332 outsl(EPPDATA(port), buf, (length >> 2)); 333 else 334 outsb(EPPDATA(port), buf, length); 335 if (inb(STATUS(port)) & 0x01) { 336 clear_epp_timeout(port); 337 return -EIO; 338 } 339 return length; 340 } 341 for (; written < length; written++) { 342 outb(*((char *)buf), EPPDATA(port)); 343 buf++; 344 if (inb(STATUS(port)) & 0x01) { 345 clear_epp_timeout(port); 346 break; 347 } 348 } 349 350 return written; 351 } 352 353 static size_t parport_pc_epp_read_addr(struct parport *port, void *buf, 354 size_t length, int flags) 355 { 356 size_t got = 0; 357 358 if ((flags & PARPORT_EPP_FAST) && (length > 1)) { 359 insb(EPPADDR(port), buf, length); 360 if (inb(STATUS(port)) & 0x01) { 361 clear_epp_timeout(port); 362 return -EIO; 363 } 364 return length; 365 } 366 for (; got < length; got++) { 367 *((char *)buf) = inb(EPPADDR(port)); 368 buf++; 369 if (inb(STATUS(port)) & 0x01) { 370 clear_epp_timeout(port); 371 break; 372 } 373 } 374 375 return got; 376 } 377 378 static size_t parport_pc_epp_write_addr(struct parport *port, 379 const void *buf, size_t length, 380 int flags) 381 { 382 size_t written = 0; 383 384 if ((flags & PARPORT_EPP_FAST) && (length > 1)) { 385 outsb(EPPADDR(port), buf, length); 386 if (inb(STATUS(port)) & 0x01) { 387 clear_epp_timeout(port); 388 return -EIO; 389 } 390 return length; 391 } 392 for (; written < length; written++) { 393 outb(*((char *)buf), EPPADDR(port)); 394 buf++; 395 if (inb(STATUS(port)) & 0x01) { 396 clear_epp_timeout(port); 397 break; 398 } 399 } 400 401 return written; 402 } 403 404 static size_t parport_pc_ecpepp_read_data(struct parport *port, void *buf, 405 size_t length, int flags) 406 { 407 size_t got; 408 409 frob_set_mode(port, ECR_EPP); 410 parport_pc_data_reverse(port); 411 parport_pc_write_control(port, 0x4); 412 got = parport_pc_epp_read_data(port, buf, length, flags); 413 frob_set_mode(port, ECR_PS2); 414 415 return got; 416 } 417 418 static size_t parport_pc_ecpepp_write_data(struct parport *port, 419 const void *buf, size_t length, 420 int flags) 421 { 422 size_t written; 423 424 frob_set_mode(port, ECR_EPP); 425 parport_pc_write_control(port, 0x4); 426 parport_pc_data_forward(port); 427 written = parport_pc_epp_write_data(port, buf, length, flags); 428 frob_set_mode(port, ECR_PS2); 429 430 return written; 431 } 432 433 static size_t parport_pc_ecpepp_read_addr(struct parport *port, void *buf, 434 size_t length, int flags) 435 { 436 size_t got; 437 438 frob_set_mode(port, ECR_EPP); 439 parport_pc_data_reverse(port); 440 parport_pc_write_control(port, 0x4); 441 got = parport_pc_epp_read_addr(port, buf, length, flags); 442 frob_set_mode(port, ECR_PS2); 443 444 return got; 445 } 446 447 static size_t parport_pc_ecpepp_write_addr(struct parport *port, 448 const void *buf, size_t length, 449 int flags) 450 { 451 size_t written; 452 453 frob_set_mode(port, ECR_EPP); 454 parport_pc_write_control(port, 0x4); 455 parport_pc_data_forward(port); 456 written = parport_pc_epp_write_addr(port, buf, length, flags); 457 frob_set_mode(port, ECR_PS2); 458 459 return written; 460 } 461 #endif /* IEEE 1284 support */ 462 463 #ifdef CONFIG_PARPORT_PC_FIFO 464 static size_t parport_pc_fifo_write_block_pio(struct parport *port, 465 const void *buf, size_t length) 466 { 467 int ret = 0; 468 const unsigned char *bufp = buf; 469 size_t left = length; 470 unsigned long expire = jiffies + port->physport->cad->timeout; 471 const int fifo = FIFO(port); 472 int poll_for = 8; /* 80 usecs */ 473 const struct parport_pc_private *priv = port->physport->private_data; 474 const int fifo_depth = priv->fifo_depth; 475 476 port = port->physport; 477 478 /* We don't want to be interrupted every character. */ 479 parport_pc_disable_irq(port); 480 /* set nErrIntrEn and serviceIntr */ 481 frob_econtrol(port, (1<<4) | (1<<2), (1<<4) | (1<<2)); 482 483 /* Forward mode. */ 484 parport_pc_data_forward(port); /* Must be in PS2 mode */ 485 486 while (left) { 487 unsigned char byte; 488 unsigned char ecrval = inb(ECONTROL(port)); 489 int i = 0; 490 491 if (need_resched() && time_before(jiffies, expire)) 492 /* Can't yield the port. */ 493 schedule(); 494 495 /* Anyone else waiting for the port? */ 496 if (port->waithead) { 497 printk(KERN_DEBUG "Somebody wants the port\n"); 498 break; 499 } 500 501 if (ecrval & 0x02) { 502 /* FIFO is full. Wait for interrupt. */ 503 504 /* Clear serviceIntr */ 505 ECR_WRITE(port, ecrval & ~(1<<2)); 506 false_alarm: 507 ret = parport_wait_event(port, HZ); 508 if (ret < 0) 509 break; 510 ret = 0; 511 if (!time_before(jiffies, expire)) { 512 /* Timed out. */ 513 printk(KERN_DEBUG "FIFO write timed out\n"); 514 break; 515 } 516 ecrval = inb(ECONTROL(port)); 517 if (!(ecrval & (1<<2))) { 518 if (need_resched() && 519 time_before(jiffies, expire)) 520 schedule(); 521 522 goto false_alarm; 523 } 524 525 continue; 526 } 527 528 /* Can't fail now. */ 529 expire = jiffies + port->cad->timeout; 530 531 poll: 532 if (signal_pending(current)) 533 break; 534 535 if (ecrval & 0x01) { 536 /* FIFO is empty. Blast it full. */ 537 const int n = left < fifo_depth ? left : fifo_depth; 538 outsb(fifo, bufp, n); 539 bufp += n; 540 left -= n; 541 542 /* Adjust the poll time. */ 543 if (i < (poll_for - 2)) 544 poll_for--; 545 continue; 546 } else if (i++ < poll_for) { 547 udelay(10); 548 ecrval = inb(ECONTROL(port)); 549 goto poll; 550 } 551 552 /* Half-full(call me an optimist) */ 553 byte = *bufp++; 554 outb(byte, fifo); 555 left--; 556 } 557 dump_parport_state("leave fifo_write_block_pio", port); 558 return length - left; 559 } 560 561 #ifdef HAS_DMA 562 static size_t parport_pc_fifo_write_block_dma(struct parport *port, 563 const void *buf, size_t length) 564 { 565 int ret = 0; 566 unsigned long dmaflag; 567 size_t left = length; 568 const struct parport_pc_private *priv = port->physport->private_data; 569 struct device *dev = port->physport->dev; 570 dma_addr_t dma_addr, dma_handle; 571 size_t maxlen = 0x10000; /* max 64k per DMA transfer */ 572 unsigned long start = (unsigned long) buf; 573 unsigned long end = (unsigned long) buf + length - 1; 574 575 dump_parport_state("enter fifo_write_block_dma", port); 576 if (end < MAX_DMA_ADDRESS) { 577 /* If it would cross a 64k boundary, cap it at the end. */ 578 if ((start ^ end) & ~0xffffUL) 579 maxlen = 0x10000 - (start & 0xffff); 580 581 dma_addr = dma_handle = dma_map_single(dev, (void *)buf, length, 582 DMA_TO_DEVICE); 583 } else { 584 /* above 16 MB we use a bounce buffer as ISA-DMA 585 is not possible */ 586 maxlen = PAGE_SIZE; /* sizeof(priv->dma_buf) */ 587 dma_addr = priv->dma_handle; 588 dma_handle = 0; 589 } 590 591 port = port->physport; 592 593 /* We don't want to be interrupted every character. */ 594 parport_pc_disable_irq(port); 595 /* set nErrIntrEn and serviceIntr */ 596 frob_econtrol(port, (1<<4) | (1<<2), (1<<4) | (1<<2)); 597 598 /* Forward mode. */ 599 parport_pc_data_forward(port); /* Must be in PS2 mode */ 600 601 while (left) { 602 unsigned long expire = jiffies + port->physport->cad->timeout; 603 604 size_t count = left; 605 606 if (count > maxlen) 607 count = maxlen; 608 609 if (!dma_handle) /* bounce buffer ! */ 610 memcpy(priv->dma_buf, buf, count); 611 612 dmaflag = claim_dma_lock(); 613 disable_dma(port->dma); 614 clear_dma_ff(port->dma); 615 set_dma_mode(port->dma, DMA_MODE_WRITE); 616 set_dma_addr(port->dma, dma_addr); 617 set_dma_count(port->dma, count); 618 619 /* Set DMA mode */ 620 frob_econtrol(port, 1<<3, 1<<3); 621 622 /* Clear serviceIntr */ 623 frob_econtrol(port, 1<<2, 0); 624 625 enable_dma(port->dma); 626 release_dma_lock(dmaflag); 627 628 /* assume DMA will be successful */ 629 left -= count; 630 buf += count; 631 if (dma_handle) 632 dma_addr += count; 633 634 /* Wait for interrupt. */ 635 false_alarm: 636 ret = parport_wait_event(port, HZ); 637 if (ret < 0) 638 break; 639 ret = 0; 640 if (!time_before(jiffies, expire)) { 641 /* Timed out. */ 642 printk(KERN_DEBUG "DMA write timed out\n"); 643 break; 644 } 645 /* Is serviceIntr set? */ 646 if (!(inb(ECONTROL(port)) & (1<<2))) { 647 cond_resched(); 648 649 goto false_alarm; 650 } 651 652 dmaflag = claim_dma_lock(); 653 disable_dma(port->dma); 654 clear_dma_ff(port->dma); 655 count = get_dma_residue(port->dma); 656 release_dma_lock(dmaflag); 657 658 cond_resched(); /* Can't yield the port. */ 659 660 /* Anyone else waiting for the port? */ 661 if (port->waithead) { 662 printk(KERN_DEBUG "Somebody wants the port\n"); 663 break; 664 } 665 666 /* update for possible DMA residue ! */ 667 buf -= count; 668 left += count; 669 if (dma_handle) 670 dma_addr -= count; 671 } 672 673 /* Maybe got here through break, so adjust for DMA residue! */ 674 dmaflag = claim_dma_lock(); 675 disable_dma(port->dma); 676 clear_dma_ff(port->dma); 677 left += get_dma_residue(port->dma); 678 release_dma_lock(dmaflag); 679 680 /* Turn off DMA mode */ 681 frob_econtrol(port, 1<<3, 0); 682 683 if (dma_handle) 684 dma_unmap_single(dev, dma_handle, length, DMA_TO_DEVICE); 685 686 dump_parport_state("leave fifo_write_block_dma", port); 687 return length - left; 688 } 689 #endif 690 691 static inline size_t parport_pc_fifo_write_block(struct parport *port, 692 const void *buf, size_t length) 693 { 694 #ifdef HAS_DMA 695 if (port->dma != PARPORT_DMA_NONE) 696 return parport_pc_fifo_write_block_dma(port, buf, length); 697 #endif 698 return parport_pc_fifo_write_block_pio(port, buf, length); 699 } 700 701 /* Parallel Port FIFO mode (ECP chipsets) */ 702 static size_t parport_pc_compat_write_block_pio(struct parport *port, 703 const void *buf, size_t length, 704 int flags) 705 { 706 size_t written; 707 int r; 708 unsigned long expire; 709 const struct parport_pc_private *priv = port->physport->private_data; 710 711 /* Special case: a timeout of zero means we cannot call schedule(). 712 * Also if O_NONBLOCK is set then use the default implementation. */ 713 if (port->physport->cad->timeout <= PARPORT_INACTIVITY_O_NONBLOCK) 714 return parport_ieee1284_write_compat(port, buf, 715 length, flags); 716 717 /* Set up parallel port FIFO mode.*/ 718 parport_pc_data_forward(port); /* Must be in PS2 mode */ 719 parport_pc_frob_control(port, PARPORT_CONTROL_STROBE, 0); 720 r = change_mode(port, ECR_PPF); /* Parallel port FIFO */ 721 if (r) 722 printk(KERN_DEBUG "%s: Warning change_mode ECR_PPF failed\n", 723 port->name); 724 725 port->physport->ieee1284.phase = IEEE1284_PH_FWD_DATA; 726 727 /* Write the data to the FIFO. */ 728 written = parport_pc_fifo_write_block(port, buf, length); 729 730 /* Finish up. */ 731 /* For some hardware we don't want to touch the mode until 732 * the FIFO is empty, so allow 4 seconds for each position 733 * in the fifo. 734 */ 735 expire = jiffies + (priv->fifo_depth * HZ * 4); 736 do { 737 /* Wait for the FIFO to empty */ 738 r = change_mode(port, ECR_PS2); 739 if (r != -EBUSY) 740 break; 741 } while (time_before(jiffies, expire)); 742 if (r == -EBUSY) { 743 744 printk(KERN_DEBUG "%s: FIFO is stuck\n", port->name); 745 746 /* Prevent further data transfer. */ 747 frob_set_mode(port, ECR_TST); 748 749 /* Adjust for the contents of the FIFO. */ 750 for (written -= priv->fifo_depth; ; written++) { 751 if (inb(ECONTROL(port)) & 0x2) { 752 /* Full up. */ 753 break; 754 } 755 outb(0, FIFO(port)); 756 } 757 758 /* Reset the FIFO and return to PS2 mode. */ 759 frob_set_mode(port, ECR_PS2); 760 } 761 762 r = parport_wait_peripheral(port, 763 PARPORT_STATUS_BUSY, 764 PARPORT_STATUS_BUSY); 765 if (r) 766 printk(KERN_DEBUG "%s: BUSY timeout (%d) in compat_write_block_pio\n", 767 port->name, r); 768 769 port->physport->ieee1284.phase = IEEE1284_PH_FWD_IDLE; 770 771 return written; 772 } 773 774 /* ECP */ 775 #ifdef CONFIG_PARPORT_1284 776 static size_t parport_pc_ecp_write_block_pio(struct parport *port, 777 const void *buf, size_t length, 778 int flags) 779 { 780 size_t written; 781 int r; 782 unsigned long expire; 783 const struct parport_pc_private *priv = port->physport->private_data; 784 785 /* Special case: a timeout of zero means we cannot call schedule(). 786 * Also if O_NONBLOCK is set then use the default implementation. */ 787 if (port->physport->cad->timeout <= PARPORT_INACTIVITY_O_NONBLOCK) 788 return parport_ieee1284_ecp_write_data(port, buf, 789 length, flags); 790 791 /* Switch to forward mode if necessary. */ 792 if (port->physport->ieee1284.phase != IEEE1284_PH_FWD_IDLE) { 793 /* Event 47: Set nInit high. */ 794 parport_frob_control(port, 795 PARPORT_CONTROL_INIT 796 | PARPORT_CONTROL_AUTOFD, 797 PARPORT_CONTROL_INIT 798 | PARPORT_CONTROL_AUTOFD); 799 800 /* Event 49: PError goes high. */ 801 r = parport_wait_peripheral(port, 802 PARPORT_STATUS_PAPEROUT, 803 PARPORT_STATUS_PAPEROUT); 804 if (r) { 805 printk(KERN_DEBUG "%s: PError timeout (%d) in ecp_write_block_pio\n", 806 port->name, r); 807 } 808 } 809 810 /* Set up ECP parallel port mode.*/ 811 parport_pc_data_forward(port); /* Must be in PS2 mode */ 812 parport_pc_frob_control(port, 813 PARPORT_CONTROL_STROBE | 814 PARPORT_CONTROL_AUTOFD, 815 0); 816 r = change_mode(port, ECR_ECP); /* ECP FIFO */ 817 if (r) 818 printk(KERN_DEBUG "%s: Warning change_mode ECR_ECP failed\n", 819 port->name); 820 port->physport->ieee1284.phase = IEEE1284_PH_FWD_DATA; 821 822 /* Write the data to the FIFO. */ 823 written = parport_pc_fifo_write_block(port, buf, length); 824 825 /* Finish up. */ 826 /* For some hardware we don't want to touch the mode until 827 * the FIFO is empty, so allow 4 seconds for each position 828 * in the fifo. 829 */ 830 expire = jiffies + (priv->fifo_depth * (HZ * 4)); 831 do { 832 /* Wait for the FIFO to empty */ 833 r = change_mode(port, ECR_PS2); 834 if (r != -EBUSY) 835 break; 836 } while (time_before(jiffies, expire)); 837 if (r == -EBUSY) { 838 839 printk(KERN_DEBUG "%s: FIFO is stuck\n", port->name); 840 841 /* Prevent further data transfer. */ 842 frob_set_mode(port, ECR_TST); 843 844 /* Adjust for the contents of the FIFO. */ 845 for (written -= priv->fifo_depth; ; written++) { 846 if (inb(ECONTROL(port)) & 0x2) { 847 /* Full up. */ 848 break; 849 } 850 outb(0, FIFO(port)); 851 } 852 853 /* Reset the FIFO and return to PS2 mode. */ 854 frob_set_mode(port, ECR_PS2); 855 856 /* Host transfer recovery. */ 857 parport_pc_data_reverse(port); /* Must be in PS2 mode */ 858 udelay(5); 859 parport_frob_control(port, PARPORT_CONTROL_INIT, 0); 860 r = parport_wait_peripheral(port, PARPORT_STATUS_PAPEROUT, 0); 861 if (r) 862 printk(KERN_DEBUG "%s: PE,1 timeout (%d) in ecp_write_block_pio\n", 863 port->name, r); 864 865 parport_frob_control(port, 866 PARPORT_CONTROL_INIT, 867 PARPORT_CONTROL_INIT); 868 r = parport_wait_peripheral(port, 869 PARPORT_STATUS_PAPEROUT, 870 PARPORT_STATUS_PAPEROUT); 871 if (r) 872 printk(KERN_DEBUG "%s: PE,2 timeout (%d) in ecp_write_block_pio\n", 873 port->name, r); 874 } 875 876 r = parport_wait_peripheral(port, 877 PARPORT_STATUS_BUSY, 878 PARPORT_STATUS_BUSY); 879 if (r) 880 printk(KERN_DEBUG "%s: BUSY timeout (%d) in ecp_write_block_pio\n", 881 port->name, r); 882 883 port->physport->ieee1284.phase = IEEE1284_PH_FWD_IDLE; 884 885 return written; 886 } 887 #endif /* IEEE 1284 support */ 888 #endif /* Allowed to use FIFO/DMA */ 889 890 891 /* 892 * ****************************************** 893 * INITIALISATION AND MODULE STUFF BELOW HERE 894 * ****************************************** 895 */ 896 897 /* GCC is not inlining extern inline function later overwritten to non-inline, 898 so we use outlined_ variants here. */ 899 static const struct parport_operations parport_pc_ops = { 900 .write_data = parport_pc_write_data, 901 .read_data = parport_pc_read_data, 902 903 .write_control = parport_pc_write_control, 904 .read_control = parport_pc_read_control, 905 .frob_control = parport_pc_frob_control, 906 907 .read_status = parport_pc_read_status, 908 909 .enable_irq = parport_pc_enable_irq, 910 .disable_irq = parport_pc_disable_irq, 911 912 .data_forward = parport_pc_data_forward, 913 .data_reverse = parport_pc_data_reverse, 914 915 .init_state = parport_pc_init_state, 916 .save_state = parport_pc_save_state, 917 .restore_state = parport_pc_restore_state, 918 919 .epp_write_data = parport_ieee1284_epp_write_data, 920 .epp_read_data = parport_ieee1284_epp_read_data, 921 .epp_write_addr = parport_ieee1284_epp_write_addr, 922 .epp_read_addr = parport_ieee1284_epp_read_addr, 923 924 .ecp_write_data = parport_ieee1284_ecp_write_data, 925 .ecp_read_data = parport_ieee1284_ecp_read_data, 926 .ecp_write_addr = parport_ieee1284_ecp_write_addr, 927 928 .compat_write_data = parport_ieee1284_write_compat, 929 .nibble_read_data = parport_ieee1284_read_nibble, 930 .byte_read_data = parport_ieee1284_read_byte, 931 932 .owner = THIS_MODULE, 933 }; 934 935 #ifdef CONFIG_PARPORT_PC_SUPERIO 936 937 static struct superio_struct *find_free_superio(void) 938 { 939 int i; 940 for (i = 0; i < NR_SUPERIOS; i++) 941 if (superios[i].io == 0) 942 return &superios[i]; 943 return NULL; 944 } 945 946 947 /* Super-IO chipset detection, Winbond, SMSC */ 948 static void show_parconfig_smsc37c669(int io, int key) 949 { 950 int cr1, cr4, cra, cr23, cr26, cr27; 951 struct superio_struct *s; 952 953 static const char *const modes[] = { 954 "SPP and Bidirectional (PS/2)", 955 "EPP and SPP", 956 "ECP", 957 "ECP and EPP" }; 958 959 outb(key, io); 960 outb(key, io); 961 outb(1, io); 962 cr1 = inb(io + 1); 963 outb(4, io); 964 cr4 = inb(io + 1); 965 outb(0x0a, io); 966 cra = inb(io + 1); 967 outb(0x23, io); 968 cr23 = inb(io + 1); 969 outb(0x26, io); 970 cr26 = inb(io + 1); 971 outb(0x27, io); 972 cr27 = inb(io + 1); 973 outb(0xaa, io); 974 975 if (verbose_probing) { 976 pr_info("SMSC 37c669 LPT Config: cr_1=0x%02x, 4=0x%02x, A=0x%2x, 23=0x%02x, 26=0x%02x, 27=0x%02x\n", 977 cr1, cr4, cra, cr23, cr26, cr27); 978 979 /* The documentation calls DMA and IRQ-Lines by letters, so 980 the board maker can/will wire them 981 appropriately/randomly... G=reserved H=IDE-irq, */ 982 pr_info("SMSC LPT Config: io=0x%04x, irq=%c, dma=%c, fifo threshold=%d\n", 983 cr23 * 4, 984 (cr27 & 0x0f) ? 'A' - 1 + (cr27 & 0x0f) : '-', 985 (cr26 & 0x0f) ? 'A' - 1 + (cr26 & 0x0f) : '-', 986 cra & 0x0f); 987 pr_info("SMSC LPT Config: enabled=%s power=%s\n", 988 (cr23 * 4 >= 0x100) ? "yes" : "no", 989 (cr1 & 4) ? "yes" : "no"); 990 pr_info("SMSC LPT Config: Port mode=%s, EPP version =%s\n", 991 (cr1 & 0x08) ? "Standard mode only (SPP)" 992 : modes[cr4 & 0x03], 993 (cr4 & 0x40) ? "1.7" : "1.9"); 994 } 995 996 /* Heuristics ! BIOS setup for this mainboard device limits 997 the choices to standard settings, i.e. io-address and IRQ 998 are related, however DMA can be 1 or 3, assume DMA_A=DMA1, 999 DMA_C=DMA3 (this is true e.g. for TYAN 1564D Tomcat IV) */ 1000 if (cr23 * 4 >= 0x100) { /* if active */ 1001 s = find_free_superio(); 1002 if (s == NULL) 1003 pr_info("Super-IO: too many chips!\n"); 1004 else { 1005 int d; 1006 switch (cr23 * 4) { 1007 case 0x3bc: 1008 s->io = 0x3bc; 1009 s->irq = 7; 1010 break; 1011 case 0x378: 1012 s->io = 0x378; 1013 s->irq = 7; 1014 break; 1015 case 0x278: 1016 s->io = 0x278; 1017 s->irq = 5; 1018 } 1019 d = (cr26 & 0x0f); 1020 if (d == 1 || d == 3) 1021 s->dma = d; 1022 else 1023 s->dma = PARPORT_DMA_NONE; 1024 } 1025 } 1026 } 1027 1028 1029 static void show_parconfig_winbond(int io, int key) 1030 { 1031 int cr30, cr60, cr61, cr70, cr74, crf0; 1032 struct superio_struct *s; 1033 static const char *const modes[] = { 1034 "Standard (SPP) and Bidirectional(PS/2)", /* 0 */ 1035 "EPP-1.9 and SPP", 1036 "ECP", 1037 "ECP and EPP-1.9", 1038 "Standard (SPP)", 1039 "EPP-1.7 and SPP", /* 5 */ 1040 "undefined!", 1041 "ECP and EPP-1.7" }; 1042 static char *const irqtypes[] = { 1043 "pulsed low, high-Z", 1044 "follows nACK" }; 1045 1046 /* The registers are called compatible-PnP because the 1047 register layout is modelled after ISA-PnP, the access 1048 method is just another ... */ 1049 outb(key, io); 1050 outb(key, io); 1051 outb(0x07, io); /* Register 7: Select Logical Device */ 1052 outb(0x01, io + 1); /* LD1 is Parallel Port */ 1053 outb(0x30, io); 1054 cr30 = inb(io + 1); 1055 outb(0x60, io); 1056 cr60 = inb(io + 1); 1057 outb(0x61, io); 1058 cr61 = inb(io + 1); 1059 outb(0x70, io); 1060 cr70 = inb(io + 1); 1061 outb(0x74, io); 1062 cr74 = inb(io + 1); 1063 outb(0xf0, io); 1064 crf0 = inb(io + 1); 1065 outb(0xaa, io); 1066 1067 if (verbose_probing) { 1068 pr_info("Winbond LPT Config: cr_30=%02x 60,61=%02x%02x 70=%02x 74=%02x, f0=%02x\n", 1069 cr30, cr60, cr61, cr70, cr74, crf0); 1070 pr_info("Winbond LPT Config: active=%s, io=0x%02x%02x irq=%d, ", 1071 (cr30 & 0x01) ? "yes" : "no", cr60, cr61, cr70 & 0x0f); 1072 if ((cr74 & 0x07) > 3) 1073 pr_cont("dma=none\n"); 1074 else 1075 pr_cont("dma=%d\n", cr74 & 0x07); 1076 pr_info("Winbond LPT Config: irqtype=%s, ECP fifo threshold=%d\n", 1077 irqtypes[crf0 >> 7], (crf0 >> 3) & 0x0f); 1078 pr_info("Winbond LPT Config: Port mode=%s\n", 1079 modes[crf0 & 0x07]); 1080 } 1081 1082 if (cr30 & 0x01) { /* the settings can be interrogated later ... */ 1083 s = find_free_superio(); 1084 if (s == NULL) 1085 pr_info("Super-IO: too many chips!\n"); 1086 else { 1087 s->io = (cr60 << 8) | cr61; 1088 s->irq = cr70 & 0x0f; 1089 s->dma = (((cr74 & 0x07) > 3) ? 1090 PARPORT_DMA_NONE : (cr74 & 0x07)); 1091 } 1092 } 1093 } 1094 1095 static void decode_winbond(int efer, int key, int devid, int devrev, int oldid) 1096 { 1097 const char *type = "unknown"; 1098 int id, progif = 2; 1099 1100 if (devid == devrev) 1101 /* simple heuristics, we happened to read some 1102 non-winbond register */ 1103 return; 1104 1105 id = (devid << 8) | devrev; 1106 1107 /* Values are from public data sheets pdf files, I can just 1108 confirm 83977TF is correct :-) */ 1109 if (id == 0x9771) 1110 type = "83977F/AF"; 1111 else if (id == 0x9773) 1112 type = "83977TF / SMSC 97w33x/97w34x"; 1113 else if (id == 0x9774) 1114 type = "83977ATF"; 1115 else if ((id & ~0x0f) == 0x5270) 1116 type = "83977CTF / SMSC 97w36x"; 1117 else if ((id & ~0x0f) == 0x52f0) 1118 type = "83977EF / SMSC 97w35x"; 1119 else if ((id & ~0x0f) == 0x5210) 1120 type = "83627"; 1121 else if ((id & ~0x0f) == 0x6010) 1122 type = "83697HF"; 1123 else if ((oldid & 0x0f) == 0x0a) { 1124 type = "83877F"; 1125 progif = 1; 1126 } else if ((oldid & 0x0f) == 0x0b) { 1127 type = "83877AF"; 1128 progif = 1; 1129 } else if ((oldid & 0x0f) == 0x0c) { 1130 type = "83877TF"; 1131 progif = 1; 1132 } else if ((oldid & 0x0f) == 0x0d) { 1133 type = "83877ATF"; 1134 progif = 1; 1135 } else 1136 progif = 0; 1137 1138 if (verbose_probing) 1139 pr_info("Winbond chip at EFER=0x%x key=0x%02x devid=%02x devrev=%02x oldid=%02x type=%s\n", 1140 efer, key, devid, devrev, oldid, type); 1141 1142 if (progif == 2) 1143 show_parconfig_winbond(efer, key); 1144 } 1145 1146 static void decode_smsc(int efer, int key, int devid, int devrev) 1147 { 1148 const char *type = "unknown"; 1149 void (*func)(int io, int key); 1150 int id; 1151 1152 if (devid == devrev) 1153 /* simple heuristics, we happened to read some 1154 non-smsc register */ 1155 return; 1156 1157 func = NULL; 1158 id = (devid << 8) | devrev; 1159 1160 if (id == 0x0302) { 1161 type = "37c669"; 1162 func = show_parconfig_smsc37c669; 1163 } else if (id == 0x6582) 1164 type = "37c665IR"; 1165 else if (devid == 0x65) 1166 type = "37c665GT"; 1167 else if (devid == 0x66) 1168 type = "37c666GT"; 1169 1170 if (verbose_probing) 1171 pr_info("SMSC chip at EFER=0x%x key=0x%02x devid=%02x devrev=%02x type=%s\n", 1172 efer, key, devid, devrev, type); 1173 1174 if (func) 1175 func(efer, key); 1176 } 1177 1178 1179 static void winbond_check(int io, int key) 1180 { 1181 int origval, devid, devrev, oldid, x_devid, x_devrev, x_oldid; 1182 1183 if (!request_region(io, 3, __func__)) 1184 return; 1185 1186 origval = inb(io); /* Save original value */ 1187 1188 /* First probe without key */ 1189 outb(0x20, io); 1190 x_devid = inb(io + 1); 1191 outb(0x21, io); 1192 x_devrev = inb(io + 1); 1193 outb(0x09, io); 1194 x_oldid = inb(io + 1); 1195 1196 outb(key, io); 1197 outb(key, io); /* Write Magic Sequence to EFER, extended 1198 function enable register */ 1199 outb(0x20, io); /* Write EFIR, extended function index register */ 1200 devid = inb(io + 1); /* Read EFDR, extended function data register */ 1201 outb(0x21, io); 1202 devrev = inb(io + 1); 1203 outb(0x09, io); 1204 oldid = inb(io + 1); 1205 outb(0xaa, io); /* Magic Seal */ 1206 1207 outb(origval, io); /* in case we poked some entirely different hardware */ 1208 1209 if ((x_devid == devid) && (x_devrev == devrev) && (x_oldid == oldid)) 1210 goto out; /* protection against false positives */ 1211 1212 decode_winbond(io, key, devid, devrev, oldid); 1213 out: 1214 release_region(io, 3); 1215 } 1216 1217 static void winbond_check2(int io, int key) 1218 { 1219 int origval[3], devid, devrev, oldid, x_devid, x_devrev, x_oldid; 1220 1221 if (!request_region(io, 3, __func__)) 1222 return; 1223 1224 origval[0] = inb(io); /* Save original values */ 1225 origval[1] = inb(io + 1); 1226 origval[2] = inb(io + 2); 1227 1228 /* First probe without the key */ 1229 outb(0x20, io + 2); 1230 x_devid = inb(io + 2); 1231 outb(0x21, io + 1); 1232 x_devrev = inb(io + 2); 1233 outb(0x09, io + 1); 1234 x_oldid = inb(io + 2); 1235 1236 outb(key, io); /* Write Magic Byte to EFER, extended 1237 function enable register */ 1238 outb(0x20, io + 2); /* Write EFIR, extended function index register */ 1239 devid = inb(io + 2); /* Read EFDR, extended function data register */ 1240 outb(0x21, io + 1); 1241 devrev = inb(io + 2); 1242 outb(0x09, io + 1); 1243 oldid = inb(io + 2); 1244 outb(0xaa, io); /* Magic Seal */ 1245 1246 outb(origval[0], io); /* in case we poked some entirely different hardware */ 1247 outb(origval[1], io + 1); 1248 outb(origval[2], io + 2); 1249 1250 if (x_devid == devid && x_devrev == devrev && x_oldid == oldid) 1251 goto out; /* protection against false positives */ 1252 1253 decode_winbond(io, key, devid, devrev, oldid); 1254 out: 1255 release_region(io, 3); 1256 } 1257 1258 static void smsc_check(int io, int key) 1259 { 1260 int origval, id, rev, oldid, oldrev, x_id, x_rev, x_oldid, x_oldrev; 1261 1262 if (!request_region(io, 3, __func__)) 1263 return; 1264 1265 origval = inb(io); /* Save original value */ 1266 1267 /* First probe without the key */ 1268 outb(0x0d, io); 1269 x_oldid = inb(io + 1); 1270 outb(0x0e, io); 1271 x_oldrev = inb(io + 1); 1272 outb(0x20, io); 1273 x_id = inb(io + 1); 1274 outb(0x21, io); 1275 x_rev = inb(io + 1); 1276 1277 outb(key, io); 1278 outb(key, io); /* Write Magic Sequence to EFER, extended 1279 function enable register */ 1280 outb(0x0d, io); /* Write EFIR, extended function index register */ 1281 oldid = inb(io + 1); /* Read EFDR, extended function data register */ 1282 outb(0x0e, io); 1283 oldrev = inb(io + 1); 1284 outb(0x20, io); 1285 id = inb(io + 1); 1286 outb(0x21, io); 1287 rev = inb(io + 1); 1288 outb(0xaa, io); /* Magic Seal */ 1289 1290 outb(origval, io); /* in case we poked some entirely different hardware */ 1291 1292 if (x_id == id && x_oldrev == oldrev && 1293 x_oldid == oldid && x_rev == rev) 1294 goto out; /* protection against false positives */ 1295 1296 decode_smsc(io, key, oldid, oldrev); 1297 out: 1298 release_region(io, 3); 1299 } 1300 1301 1302 static void detect_and_report_winbond(void) 1303 { 1304 if (verbose_probing) 1305 printk(KERN_DEBUG "Winbond Super-IO detection, now testing ports 3F0,370,250,4E,2E ...\n"); 1306 winbond_check(0x3f0, 0x87); 1307 winbond_check(0x370, 0x87); 1308 winbond_check(0x2e , 0x87); 1309 winbond_check(0x4e , 0x87); 1310 winbond_check(0x3f0, 0x86); 1311 winbond_check2(0x250, 0x88); 1312 winbond_check2(0x250, 0x89); 1313 } 1314 1315 static void detect_and_report_smsc(void) 1316 { 1317 if (verbose_probing) 1318 printk(KERN_DEBUG "SMSC Super-IO detection, now testing Ports 2F0, 370 ...\n"); 1319 smsc_check(0x3f0, 0x55); 1320 smsc_check(0x370, 0x55); 1321 smsc_check(0x3f0, 0x44); 1322 smsc_check(0x370, 0x44); 1323 } 1324 1325 static void detect_and_report_it87(void) 1326 { 1327 u16 dev; 1328 u8 origval, r; 1329 if (verbose_probing) 1330 printk(KERN_DEBUG "IT8705 Super-IO detection, now testing port 2E ...\n"); 1331 if (!request_muxed_region(0x2e, 2, __func__)) 1332 return; 1333 origval = inb(0x2e); /* Save original value */ 1334 outb(0x87, 0x2e); 1335 outb(0x01, 0x2e); 1336 outb(0x55, 0x2e); 1337 outb(0x55, 0x2e); 1338 outb(0x20, 0x2e); 1339 dev = inb(0x2f) << 8; 1340 outb(0x21, 0x2e); 1341 dev |= inb(0x2f); 1342 if (dev == 0x8712 || dev == 0x8705 || dev == 0x8715 || 1343 dev == 0x8716 || dev == 0x8718 || dev == 0x8726) { 1344 pr_info("IT%04X SuperIO detected\n", dev); 1345 outb(0x07, 0x2E); /* Parallel Port */ 1346 outb(0x03, 0x2F); 1347 outb(0xF0, 0x2E); /* BOOT 0x80 off */ 1348 r = inb(0x2f); 1349 outb(0xF0, 0x2E); 1350 outb(r | 8, 0x2F); 1351 outb(0x02, 0x2E); /* Lock */ 1352 outb(0x02, 0x2F); 1353 } else { 1354 outb(origval, 0x2e); /* Oops, sorry to disturb */ 1355 } 1356 release_region(0x2e, 2); 1357 } 1358 #endif /* CONFIG_PARPORT_PC_SUPERIO */ 1359 1360 static struct superio_struct *find_superio(struct parport *p) 1361 { 1362 int i; 1363 for (i = 0; i < NR_SUPERIOS; i++) 1364 if (superios[i].io == p->base) 1365 return &superios[i]; 1366 return NULL; 1367 } 1368 1369 static int get_superio_dma(struct parport *p) 1370 { 1371 struct superio_struct *s = find_superio(p); 1372 if (s) 1373 return s->dma; 1374 return PARPORT_DMA_NONE; 1375 } 1376 1377 static int get_superio_irq(struct parport *p) 1378 { 1379 struct superio_struct *s = find_superio(p); 1380 if (s) 1381 return s->irq; 1382 return PARPORT_IRQ_NONE; 1383 } 1384 1385 1386 /* --- Mode detection ------------------------------------- */ 1387 1388 /* 1389 * Checks for port existence, all ports support SPP MODE 1390 * Returns: 1391 * 0 : No parallel port at this address 1392 * PARPORT_MODE_PCSPP : SPP port detected 1393 * (if the user specified an ioport himself, 1394 * this shall always be the case!) 1395 * 1396 */ 1397 static int parport_SPP_supported(struct parport *pb) 1398 { 1399 unsigned char r, w; 1400 1401 /* 1402 * first clear an eventually pending EPP timeout 1403 * I (sailer@ife.ee.ethz.ch) have an SMSC chipset 1404 * that does not even respond to SPP cycles if an EPP 1405 * timeout is pending 1406 */ 1407 clear_epp_timeout(pb); 1408 1409 /* Do a simple read-write test to make sure the port exists. */ 1410 w = 0xc; 1411 outb(w, CONTROL(pb)); 1412 1413 /* Is there a control register that we can read from? Some 1414 * ports don't allow reads, so read_control just returns a 1415 * software copy. Some ports _do_ allow reads, so bypass the 1416 * software copy here. In addition, some bits aren't 1417 * writable. */ 1418 r = inb(CONTROL(pb)); 1419 if ((r & 0xf) == w) { 1420 w = 0xe; 1421 outb(w, CONTROL(pb)); 1422 r = inb(CONTROL(pb)); 1423 outb(0xc, CONTROL(pb)); 1424 if ((r & 0xf) == w) 1425 return PARPORT_MODE_PCSPP; 1426 } 1427 1428 if (user_specified) 1429 /* That didn't work, but the user thinks there's a 1430 * port here. */ 1431 pr_info("parport 0x%lx (WARNING): CTR: wrote 0x%02x, read 0x%02x\n", 1432 pb->base, w, r); 1433 1434 /* Try the data register. The data lines aren't tri-stated at 1435 * this stage, so we expect back what we wrote. */ 1436 w = 0xaa; 1437 parport_pc_write_data(pb, w); 1438 r = parport_pc_read_data(pb); 1439 if (r == w) { 1440 w = 0x55; 1441 parport_pc_write_data(pb, w); 1442 r = parport_pc_read_data(pb); 1443 if (r == w) 1444 return PARPORT_MODE_PCSPP; 1445 } 1446 1447 if (user_specified) { 1448 /* Didn't work, but the user is convinced this is the 1449 * place. */ 1450 pr_info("parport 0x%lx (WARNING): DATA: wrote 0x%02x, read 0x%02x\n", 1451 pb->base, w, r); 1452 pr_info("parport 0x%lx: You gave this address, but there is probably no parallel port there!\n", 1453 pb->base); 1454 } 1455 1456 /* It's possible that we can't read the control register or 1457 * the data register. In that case just believe the user. */ 1458 if (user_specified) 1459 return PARPORT_MODE_PCSPP; 1460 1461 return 0; 1462 } 1463 1464 /* Check for ECR 1465 * 1466 * Old style XT ports alias io ports every 0x400, hence accessing ECR 1467 * on these cards actually accesses the CTR. 1468 * 1469 * Modern cards don't do this but reading from ECR will return 0xff 1470 * regardless of what is written here if the card does NOT support 1471 * ECP. 1472 * 1473 * We first check to see if ECR is the same as CTR. If not, the low 1474 * two bits of ECR aren't writable, so we check by writing ECR and 1475 * reading it back to see if it's what we expect. 1476 */ 1477 static int parport_ECR_present(struct parport *pb) 1478 { 1479 struct parport_pc_private *priv = pb->private_data; 1480 unsigned char r = 0xc; 1481 1482 outb(r, CONTROL(pb)); 1483 if ((inb(ECONTROL(pb)) & 0x3) == (r & 0x3)) { 1484 outb(r ^ 0x2, CONTROL(pb)); /* Toggle bit 1 */ 1485 1486 r = inb(CONTROL(pb)); 1487 if ((inb(ECONTROL(pb)) & 0x2) == (r & 0x2)) 1488 goto no_reg; /* Sure that no ECR register exists */ 1489 } 1490 1491 if ((inb(ECONTROL(pb)) & 0x3) != 0x1) 1492 goto no_reg; 1493 1494 ECR_WRITE(pb, 0x34); 1495 if (inb(ECONTROL(pb)) != 0x35) 1496 goto no_reg; 1497 1498 priv->ecr = 1; 1499 outb(0xc, CONTROL(pb)); 1500 1501 /* Go to mode 000 */ 1502 frob_set_mode(pb, ECR_SPP); 1503 1504 return 1; 1505 1506 no_reg: 1507 outb(0xc, CONTROL(pb)); 1508 return 0; 1509 } 1510 1511 #ifdef CONFIG_PARPORT_1284 1512 /* Detect PS/2 support. 1513 * 1514 * Bit 5 (0x20) sets the PS/2 data direction; setting this high 1515 * allows us to read data from the data lines. In theory we would get back 1516 * 0xff but any peripheral attached to the port may drag some or all of the 1517 * lines down to zero. So if we get back anything that isn't the contents 1518 * of the data register we deem PS/2 support to be present. 1519 * 1520 * Some SPP ports have "half PS/2" ability - you can't turn off the line 1521 * drivers, but an external peripheral with sufficiently beefy drivers of 1522 * its own can overpower them and assert its own levels onto the bus, from 1523 * where they can then be read back as normal. Ports with this property 1524 * and the right type of device attached are likely to fail the SPP test, 1525 * (as they will appear to have stuck bits) and so the fact that they might 1526 * be misdetected here is rather academic. 1527 */ 1528 1529 static int parport_PS2_supported(struct parport *pb) 1530 { 1531 int ok = 0; 1532 1533 clear_epp_timeout(pb); 1534 1535 /* try to tri-state the buffer */ 1536 parport_pc_data_reverse(pb); 1537 1538 parport_pc_write_data(pb, 0x55); 1539 if (parport_pc_read_data(pb) != 0x55) 1540 ok++; 1541 1542 parport_pc_write_data(pb, 0xaa); 1543 if (parport_pc_read_data(pb) != 0xaa) 1544 ok++; 1545 1546 /* cancel input mode */ 1547 parport_pc_data_forward(pb); 1548 1549 if (ok) { 1550 pb->modes |= PARPORT_MODE_TRISTATE; 1551 } else { 1552 struct parport_pc_private *priv = pb->private_data; 1553 priv->ctr_writable &= ~0x20; 1554 } 1555 1556 return ok; 1557 } 1558 1559 #ifdef CONFIG_PARPORT_PC_FIFO 1560 static int parport_ECP_supported(struct parport *pb) 1561 { 1562 int i; 1563 int config, configb; 1564 int pword; 1565 struct parport_pc_private *priv = pb->private_data; 1566 /* Translate ECP intrLine to ISA irq value */ 1567 static const int intrline[] = { 0, 7, 9, 10, 11, 14, 15, 5 }; 1568 1569 /* If there is no ECR, we have no hope of supporting ECP. */ 1570 if (!priv->ecr) 1571 return 0; 1572 1573 /* Find out FIFO depth */ 1574 ECR_WRITE(pb, ECR_SPP << 5); /* Reset FIFO */ 1575 ECR_WRITE(pb, ECR_TST << 5); /* TEST FIFO */ 1576 for (i = 0; i < 1024 && !(inb(ECONTROL(pb)) & 0x02); i++) 1577 outb(0xaa, FIFO(pb)); 1578 1579 /* 1580 * Using LGS chipset it uses ECR register, but 1581 * it doesn't support ECP or FIFO MODE 1582 */ 1583 if (i == 1024) { 1584 ECR_WRITE(pb, ECR_SPP << 5); 1585 return 0; 1586 } 1587 1588 priv->fifo_depth = i; 1589 if (verbose_probing) 1590 printk(KERN_DEBUG "0x%lx: FIFO is %d bytes\n", pb->base, i); 1591 1592 /* Find out writeIntrThreshold */ 1593 frob_econtrol(pb, 1<<2, 1<<2); 1594 frob_econtrol(pb, 1<<2, 0); 1595 for (i = 1; i <= priv->fifo_depth; i++) { 1596 inb(FIFO(pb)); 1597 udelay(50); 1598 if (inb(ECONTROL(pb)) & (1<<2)) 1599 break; 1600 } 1601 1602 if (i <= priv->fifo_depth) { 1603 if (verbose_probing) 1604 printk(KERN_DEBUG "0x%lx: writeIntrThreshold is %d\n", 1605 pb->base, i); 1606 } else 1607 /* Number of bytes we know we can write if we get an 1608 interrupt. */ 1609 i = 0; 1610 1611 priv->writeIntrThreshold = i; 1612 1613 /* Find out readIntrThreshold */ 1614 frob_set_mode(pb, ECR_PS2); /* Reset FIFO and enable PS2 */ 1615 parport_pc_data_reverse(pb); /* Must be in PS2 mode */ 1616 frob_set_mode(pb, ECR_TST); /* Test FIFO */ 1617 frob_econtrol(pb, 1<<2, 1<<2); 1618 frob_econtrol(pb, 1<<2, 0); 1619 for (i = 1; i <= priv->fifo_depth; i++) { 1620 outb(0xaa, FIFO(pb)); 1621 if (inb(ECONTROL(pb)) & (1<<2)) 1622 break; 1623 } 1624 1625 if (i <= priv->fifo_depth) { 1626 if (verbose_probing) 1627 pr_info("0x%lx: readIntrThreshold is %d\n", 1628 pb->base, i); 1629 } else 1630 /* Number of bytes we can read if we get an interrupt. */ 1631 i = 0; 1632 1633 priv->readIntrThreshold = i; 1634 1635 ECR_WRITE(pb, ECR_SPP << 5); /* Reset FIFO */ 1636 ECR_WRITE(pb, 0xf4); /* Configuration mode */ 1637 config = inb(CONFIGA(pb)); 1638 pword = (config >> 4) & 0x7; 1639 switch (pword) { 1640 case 0: 1641 pword = 2; 1642 pr_warn("0x%lx: Unsupported pword size!\n", pb->base); 1643 break; 1644 case 2: 1645 pword = 4; 1646 pr_warn("0x%lx: Unsupported pword size!\n", pb->base); 1647 break; 1648 default: 1649 pr_warn("0x%lx: Unknown implementation ID\n", pb->base); 1650 /* Fall through - Assume 1 */ 1651 case 1: 1652 pword = 1; 1653 } 1654 priv->pword = pword; 1655 1656 if (verbose_probing) { 1657 printk(KERN_DEBUG "0x%lx: PWord is %d bits\n", 1658 pb->base, 8 * pword); 1659 1660 printk(KERN_DEBUG "0x%lx: Interrupts are ISA-%s\n", 1661 pb->base, config & 0x80 ? "Level" : "Pulses"); 1662 1663 configb = inb(CONFIGB(pb)); 1664 printk(KERN_DEBUG "0x%lx: ECP port cfgA=0x%02x cfgB=0x%02x\n", 1665 pb->base, config, configb); 1666 printk(KERN_DEBUG "0x%lx: ECP settings irq=", pb->base); 1667 if ((configb >> 3) & 0x07) 1668 pr_cont("%d", intrline[(configb >> 3) & 0x07]); 1669 else 1670 pr_cont("<none or set by other means>"); 1671 pr_cont(" dma="); 1672 if ((configb & 0x03) == 0x00) 1673 pr_cont("<none or set by other means>\n"); 1674 else 1675 pr_cont("%d\n", configb & 0x07); 1676 } 1677 1678 /* Go back to mode 000 */ 1679 frob_set_mode(pb, ECR_SPP); 1680 1681 return 1; 1682 } 1683 #endif 1684 1685 #ifdef CONFIG_X86_32 1686 static int intel_bug_present_check_epp(struct parport *pb) 1687 { 1688 const struct parport_pc_private *priv = pb->private_data; 1689 int bug_present = 0; 1690 1691 if (priv->ecr) { 1692 /* store value of ECR */ 1693 unsigned char ecr = inb(ECONTROL(pb)); 1694 unsigned char i; 1695 for (i = 0x00; i < 0x80; i += 0x20) { 1696 ECR_WRITE(pb, i); 1697 if (clear_epp_timeout(pb)) { 1698 /* Phony EPP in ECP. */ 1699 bug_present = 1; 1700 break; 1701 } 1702 } 1703 /* return ECR into the inital state */ 1704 ECR_WRITE(pb, ecr); 1705 } 1706 1707 return bug_present; 1708 } 1709 static int intel_bug_present(struct parport *pb) 1710 { 1711 /* Check whether the device is legacy, not PCI or PCMCIA. Only legacy is known to be affected. */ 1712 if (pb->dev != NULL) { 1713 return 0; 1714 } 1715 1716 return intel_bug_present_check_epp(pb); 1717 } 1718 #else 1719 static int intel_bug_present(struct parport *pb) 1720 { 1721 return 0; 1722 } 1723 #endif /* CONFIG_X86_32 */ 1724 1725 static int parport_ECPPS2_supported(struct parport *pb) 1726 { 1727 const struct parport_pc_private *priv = pb->private_data; 1728 int result; 1729 unsigned char oecr; 1730 1731 if (!priv->ecr) 1732 return 0; 1733 1734 oecr = inb(ECONTROL(pb)); 1735 ECR_WRITE(pb, ECR_PS2 << 5); 1736 result = parport_PS2_supported(pb); 1737 ECR_WRITE(pb, oecr); 1738 return result; 1739 } 1740 1741 /* EPP mode detection */ 1742 1743 static int parport_EPP_supported(struct parport *pb) 1744 { 1745 /* 1746 * Theory: 1747 * Bit 0 of STR is the EPP timeout bit, this bit is 0 1748 * when EPP is possible and is set high when an EPP timeout 1749 * occurs (EPP uses the HALT line to stop the CPU while it does 1750 * the byte transfer, an EPP timeout occurs if the attached 1751 * device fails to respond after 10 micro seconds). 1752 * 1753 * This bit is cleared by either reading it (National Semi) 1754 * or writing a 1 to the bit (SMC, UMC, WinBond), others ??? 1755 * This bit is always high in non EPP modes. 1756 */ 1757 1758 /* If EPP timeout bit clear then EPP available */ 1759 if (!clear_epp_timeout(pb)) 1760 return 0; /* No way to clear timeout */ 1761 1762 /* Check for Intel bug. */ 1763 if (intel_bug_present(pb)) 1764 return 0; 1765 1766 pb->modes |= PARPORT_MODE_EPP; 1767 1768 /* Set up access functions to use EPP hardware. */ 1769 pb->ops->epp_read_data = parport_pc_epp_read_data; 1770 pb->ops->epp_write_data = parport_pc_epp_write_data; 1771 pb->ops->epp_read_addr = parport_pc_epp_read_addr; 1772 pb->ops->epp_write_addr = parport_pc_epp_write_addr; 1773 1774 return 1; 1775 } 1776 1777 static int parport_ECPEPP_supported(struct parport *pb) 1778 { 1779 struct parport_pc_private *priv = pb->private_data; 1780 int result; 1781 unsigned char oecr; 1782 1783 if (!priv->ecr) 1784 return 0; 1785 1786 oecr = inb(ECONTROL(pb)); 1787 /* Search for SMC style EPP+ECP mode */ 1788 ECR_WRITE(pb, 0x80); 1789 outb(0x04, CONTROL(pb)); 1790 result = parport_EPP_supported(pb); 1791 1792 ECR_WRITE(pb, oecr); 1793 1794 if (result) { 1795 /* Set up access functions to use ECP+EPP hardware. */ 1796 pb->ops->epp_read_data = parport_pc_ecpepp_read_data; 1797 pb->ops->epp_write_data = parport_pc_ecpepp_write_data; 1798 pb->ops->epp_read_addr = parport_pc_ecpepp_read_addr; 1799 pb->ops->epp_write_addr = parport_pc_ecpepp_write_addr; 1800 } 1801 1802 return result; 1803 } 1804 1805 #else /* No IEEE 1284 support */ 1806 1807 /* Don't bother probing for modes we know we won't use. */ 1808 static int parport_PS2_supported(struct parport *pb) { return 0; } 1809 #ifdef CONFIG_PARPORT_PC_FIFO 1810 static int parport_ECP_supported(struct parport *pb) 1811 { 1812 return 0; 1813 } 1814 #endif 1815 static int parport_EPP_supported(struct parport *pb) 1816 { 1817 return 0; 1818 } 1819 1820 static int parport_ECPEPP_supported(struct parport *pb) 1821 { 1822 return 0; 1823 } 1824 1825 static int parport_ECPPS2_supported(struct parport *pb) 1826 { 1827 return 0; 1828 } 1829 1830 #endif /* No IEEE 1284 support */ 1831 1832 /* --- IRQ detection -------------------------------------- */ 1833 1834 /* Only if supports ECP mode */ 1835 static int programmable_irq_support(struct parport *pb) 1836 { 1837 int irq, intrLine; 1838 unsigned char oecr = inb(ECONTROL(pb)); 1839 static const int lookup[8] = { 1840 PARPORT_IRQ_NONE, 7, 9, 10, 11, 14, 15, 5 1841 }; 1842 1843 ECR_WRITE(pb, ECR_CNF << 5); /* Configuration MODE */ 1844 1845 intrLine = (inb(CONFIGB(pb)) >> 3) & 0x07; 1846 irq = lookup[intrLine]; 1847 1848 ECR_WRITE(pb, oecr); 1849 return irq; 1850 } 1851 1852 static int irq_probe_ECP(struct parport *pb) 1853 { 1854 int i; 1855 unsigned long irqs; 1856 1857 irqs = probe_irq_on(); 1858 1859 ECR_WRITE(pb, ECR_SPP << 5); /* Reset FIFO */ 1860 ECR_WRITE(pb, (ECR_TST << 5) | 0x04); 1861 ECR_WRITE(pb, ECR_TST << 5); 1862 1863 /* If Full FIFO sure that writeIntrThreshold is generated */ 1864 for (i = 0; i < 1024 && !(inb(ECONTROL(pb)) & 0x02) ; i++) 1865 outb(0xaa, FIFO(pb)); 1866 1867 pb->irq = probe_irq_off(irqs); 1868 ECR_WRITE(pb, ECR_SPP << 5); 1869 1870 if (pb->irq <= 0) 1871 pb->irq = PARPORT_IRQ_NONE; 1872 1873 return pb->irq; 1874 } 1875 1876 /* 1877 * This detection seems that only works in National Semiconductors 1878 * This doesn't work in SMC, LGS, and Winbond 1879 */ 1880 static int irq_probe_EPP(struct parport *pb) 1881 { 1882 #ifndef ADVANCED_DETECT 1883 return PARPORT_IRQ_NONE; 1884 #else 1885 int irqs; 1886 unsigned char oecr; 1887 1888 if (pb->modes & PARPORT_MODE_PCECR) 1889 oecr = inb(ECONTROL(pb)); 1890 1891 irqs = probe_irq_on(); 1892 1893 if (pb->modes & PARPORT_MODE_PCECR) 1894 frob_econtrol(pb, 0x10, 0x10); 1895 1896 clear_epp_timeout(pb); 1897 parport_pc_frob_control(pb, 0x20, 0x20); 1898 parport_pc_frob_control(pb, 0x10, 0x10); 1899 clear_epp_timeout(pb); 1900 1901 /* Device isn't expecting an EPP read 1902 * and generates an IRQ. 1903 */ 1904 parport_pc_read_epp(pb); 1905 udelay(20); 1906 1907 pb->irq = probe_irq_off(irqs); 1908 if (pb->modes & PARPORT_MODE_PCECR) 1909 ECR_WRITE(pb, oecr); 1910 parport_pc_write_control(pb, 0xc); 1911 1912 if (pb->irq <= 0) 1913 pb->irq = PARPORT_IRQ_NONE; 1914 1915 return pb->irq; 1916 #endif /* Advanced detection */ 1917 } 1918 1919 static int irq_probe_SPP(struct parport *pb) 1920 { 1921 /* Don't even try to do this. */ 1922 return PARPORT_IRQ_NONE; 1923 } 1924 1925 /* We will attempt to share interrupt requests since other devices 1926 * such as sound cards and network cards seem to like using the 1927 * printer IRQs. 1928 * 1929 * When ECP is available we can autoprobe for IRQs. 1930 * NOTE: If we can autoprobe it, we can register the IRQ. 1931 */ 1932 static int parport_irq_probe(struct parport *pb) 1933 { 1934 struct parport_pc_private *priv = pb->private_data; 1935 1936 if (priv->ecr) { 1937 pb->irq = programmable_irq_support(pb); 1938 1939 if (pb->irq == PARPORT_IRQ_NONE) 1940 pb->irq = irq_probe_ECP(pb); 1941 } 1942 1943 if ((pb->irq == PARPORT_IRQ_NONE) && priv->ecr && 1944 (pb->modes & PARPORT_MODE_EPP)) 1945 pb->irq = irq_probe_EPP(pb); 1946 1947 clear_epp_timeout(pb); 1948 1949 if (pb->irq == PARPORT_IRQ_NONE && (pb->modes & PARPORT_MODE_EPP)) 1950 pb->irq = irq_probe_EPP(pb); 1951 1952 clear_epp_timeout(pb); 1953 1954 if (pb->irq == PARPORT_IRQ_NONE) 1955 pb->irq = irq_probe_SPP(pb); 1956 1957 if (pb->irq == PARPORT_IRQ_NONE) 1958 pb->irq = get_superio_irq(pb); 1959 1960 return pb->irq; 1961 } 1962 1963 /* --- DMA detection -------------------------------------- */ 1964 1965 /* Only if chipset conforms to ECP ISA Interface Standard */ 1966 static int programmable_dma_support(struct parport *p) 1967 { 1968 unsigned char oecr = inb(ECONTROL(p)); 1969 int dma; 1970 1971 frob_set_mode(p, ECR_CNF); 1972 1973 dma = inb(CONFIGB(p)) & 0x07; 1974 /* 000: Indicates jumpered 8-bit DMA if read-only. 1975 100: Indicates jumpered 16-bit DMA if read-only. */ 1976 if ((dma & 0x03) == 0) 1977 dma = PARPORT_DMA_NONE; 1978 1979 ECR_WRITE(p, oecr); 1980 return dma; 1981 } 1982 1983 static int parport_dma_probe(struct parport *p) 1984 { 1985 const struct parport_pc_private *priv = p->private_data; 1986 if (priv->ecr) /* ask ECP chipset first */ 1987 p->dma = programmable_dma_support(p); 1988 if (p->dma == PARPORT_DMA_NONE) { 1989 /* ask known Super-IO chips proper, although these 1990 claim ECP compatible, some don't report their DMA 1991 conforming to ECP standards */ 1992 p->dma = get_superio_dma(p); 1993 } 1994 1995 return p->dma; 1996 } 1997 1998 /* --- Initialisation code -------------------------------- */ 1999 2000 static LIST_HEAD(ports_list); 2001 static DEFINE_SPINLOCK(ports_lock); 2002 2003 struct parport *parport_pc_probe_port(unsigned long int base, 2004 unsigned long int base_hi, 2005 int irq, int dma, 2006 struct device *dev, 2007 int irqflags) 2008 { 2009 struct parport_pc_private *priv; 2010 struct parport_operations *ops; 2011 struct parport *p; 2012 int probedirq = PARPORT_IRQ_NONE; 2013 struct resource *base_res; 2014 struct resource *ECR_res = NULL; 2015 struct resource *EPP_res = NULL; 2016 struct platform_device *pdev = NULL; 2017 int ret; 2018 2019 if (!dev) { 2020 /* We need a physical device to attach to, but none was 2021 * provided. Create our own. */ 2022 pdev = platform_device_register_simple("parport_pc", 2023 base, NULL, 0); 2024 if (IS_ERR(pdev)) 2025 return NULL; 2026 dev = &pdev->dev; 2027 2028 ret = dma_coerce_mask_and_coherent(dev, DMA_BIT_MASK(24)); 2029 if (ret) { 2030 dev_err(dev, "Unable to set coherent dma mask: disabling DMA\n"); 2031 dma = PARPORT_DMA_NONE; 2032 } 2033 } 2034 2035 ops = kmalloc(sizeof(struct parport_operations), GFP_KERNEL); 2036 if (!ops) 2037 goto out1; 2038 2039 priv = kmalloc(sizeof(struct parport_pc_private), GFP_KERNEL); 2040 if (!priv) 2041 goto out2; 2042 2043 /* a misnomer, actually - it's allocate and reserve parport number */ 2044 p = parport_register_port(base, irq, dma, ops); 2045 if (!p) 2046 goto out3; 2047 2048 base_res = request_region(base, 3, p->name); 2049 if (!base_res) 2050 goto out4; 2051 2052 memcpy(ops, &parport_pc_ops, sizeof(struct parport_operations)); 2053 priv->ctr = 0xc; 2054 priv->ctr_writable = ~0x10; 2055 priv->ecr = 0; 2056 priv->fifo_depth = 0; 2057 priv->dma_buf = NULL; 2058 priv->dma_handle = 0; 2059 INIT_LIST_HEAD(&priv->list); 2060 priv->port = p; 2061 2062 p->dev = dev; 2063 p->base_hi = base_hi; 2064 p->modes = PARPORT_MODE_PCSPP | PARPORT_MODE_SAFEININT; 2065 p->private_data = priv; 2066 2067 if (base_hi) { 2068 ECR_res = request_region(base_hi, 3, p->name); 2069 if (ECR_res) 2070 parport_ECR_present(p); 2071 } 2072 2073 if (base != 0x3bc) { 2074 EPP_res = request_region(base+0x3, 5, p->name); 2075 if (EPP_res) 2076 if (!parport_EPP_supported(p)) 2077 parport_ECPEPP_supported(p); 2078 } 2079 if (!parport_SPP_supported(p)) 2080 /* No port. */ 2081 goto out5; 2082 if (priv->ecr) 2083 parport_ECPPS2_supported(p); 2084 else 2085 parport_PS2_supported(p); 2086 2087 p->size = (p->modes & PARPORT_MODE_EPP) ? 8 : 3; 2088 2089 pr_info("%s: PC-style at 0x%lx", p->name, p->base); 2090 if (p->base_hi && priv->ecr) 2091 pr_cont(" (0x%lx)", p->base_hi); 2092 if (p->irq == PARPORT_IRQ_AUTO) { 2093 p->irq = PARPORT_IRQ_NONE; 2094 parport_irq_probe(p); 2095 } else if (p->irq == PARPORT_IRQ_PROBEONLY) { 2096 p->irq = PARPORT_IRQ_NONE; 2097 parport_irq_probe(p); 2098 probedirq = p->irq; 2099 p->irq = PARPORT_IRQ_NONE; 2100 } 2101 if (p->irq != PARPORT_IRQ_NONE) { 2102 pr_cont(", irq %d", p->irq); 2103 priv->ctr_writable |= 0x10; 2104 2105 if (p->dma == PARPORT_DMA_AUTO) { 2106 p->dma = PARPORT_DMA_NONE; 2107 parport_dma_probe(p); 2108 } 2109 } 2110 if (p->dma == PARPORT_DMA_AUTO) /* To use DMA, giving the irq 2111 is mandatory (see above) */ 2112 p->dma = PARPORT_DMA_NONE; 2113 2114 #ifdef CONFIG_PARPORT_PC_FIFO 2115 if (parport_ECP_supported(p) && 2116 p->dma != PARPORT_DMA_NOFIFO && 2117 priv->fifo_depth > 0 && p->irq != PARPORT_IRQ_NONE) { 2118 p->modes |= PARPORT_MODE_ECP | PARPORT_MODE_COMPAT; 2119 p->ops->compat_write_data = parport_pc_compat_write_block_pio; 2120 #ifdef CONFIG_PARPORT_1284 2121 p->ops->ecp_write_data = parport_pc_ecp_write_block_pio; 2122 /* currently broken, but working on it.. (FB) */ 2123 /* p->ops->ecp_read_data = parport_pc_ecp_read_block_pio; */ 2124 #endif /* IEEE 1284 support */ 2125 if (p->dma != PARPORT_DMA_NONE) { 2126 pr_cont(", dma %d", p->dma); 2127 p->modes |= PARPORT_MODE_DMA; 2128 } else 2129 pr_cont(", using FIFO"); 2130 } else 2131 /* We can't use the DMA channel after all. */ 2132 p->dma = PARPORT_DMA_NONE; 2133 #endif /* Allowed to use FIFO/DMA */ 2134 2135 pr_cont(" ["); 2136 2137 #define printmode(x) \ 2138 do { \ 2139 if (p->modes & PARPORT_MODE_##x) \ 2140 pr_cont("%s%s", f++ ? "," : "", #x); \ 2141 } while (0) 2142 2143 { 2144 int f = 0; 2145 printmode(PCSPP); 2146 printmode(TRISTATE); 2147 printmode(COMPAT); 2148 printmode(EPP); 2149 printmode(ECP); 2150 printmode(DMA); 2151 } 2152 #undef printmode 2153 #ifndef CONFIG_PARPORT_1284 2154 pr_cont("(,...)"); 2155 #endif /* CONFIG_PARPORT_1284 */ 2156 pr_cont("]\n"); 2157 if (probedirq != PARPORT_IRQ_NONE) 2158 pr_info("%s: irq %d detected\n", p->name, probedirq); 2159 2160 /* If No ECP release the ports grabbed above. */ 2161 if (ECR_res && (p->modes & PARPORT_MODE_ECP) == 0) { 2162 release_region(base_hi, 3); 2163 ECR_res = NULL; 2164 } 2165 /* Likewise for EEP ports */ 2166 if (EPP_res && (p->modes & PARPORT_MODE_EPP) == 0) { 2167 release_region(base+3, 5); 2168 EPP_res = NULL; 2169 } 2170 if (p->irq != PARPORT_IRQ_NONE) { 2171 if (request_irq(p->irq, parport_irq_handler, 2172 irqflags, p->name, p)) { 2173 pr_warn("%s: irq %d in use, resorting to polled operation\n", 2174 p->name, p->irq); 2175 p->irq = PARPORT_IRQ_NONE; 2176 p->dma = PARPORT_DMA_NONE; 2177 } 2178 2179 #ifdef CONFIG_PARPORT_PC_FIFO 2180 #ifdef HAS_DMA 2181 if (p->dma != PARPORT_DMA_NONE) { 2182 if (request_dma(p->dma, p->name)) { 2183 pr_warn("%s: dma %d in use, resorting to PIO operation\n", 2184 p->name, p->dma); 2185 p->dma = PARPORT_DMA_NONE; 2186 } else { 2187 priv->dma_buf = 2188 dma_alloc_coherent(dev, 2189 PAGE_SIZE, 2190 &priv->dma_handle, 2191 GFP_KERNEL); 2192 if (!priv->dma_buf) { 2193 pr_warn("%s: cannot get buffer for DMA, resorting to PIO operation\n", 2194 p->name); 2195 free_dma(p->dma); 2196 p->dma = PARPORT_DMA_NONE; 2197 } 2198 } 2199 } 2200 #endif 2201 #endif 2202 } 2203 2204 /* Done probing. Now put the port into a sensible start-up state. */ 2205 if (priv->ecr) 2206 /* 2207 * Put the ECP detected port in PS2 mode. 2208 * Do this also for ports that have ECR but don't do ECP. 2209 */ 2210 ECR_WRITE(p, 0x34); 2211 2212 parport_pc_write_data(p, 0); 2213 parport_pc_data_forward(p); 2214 2215 /* Now that we've told the sharing engine about the port, and 2216 found out its characteristics, let the high-level drivers 2217 know about it. */ 2218 spin_lock(&ports_lock); 2219 list_add(&priv->list, &ports_list); 2220 spin_unlock(&ports_lock); 2221 parport_announce_port(p); 2222 2223 return p; 2224 2225 out5: 2226 if (ECR_res) 2227 release_region(base_hi, 3); 2228 if (EPP_res) 2229 release_region(base+0x3, 5); 2230 release_region(base, 3); 2231 out4: 2232 parport_del_port(p); 2233 out3: 2234 kfree(priv); 2235 out2: 2236 kfree(ops); 2237 out1: 2238 if (pdev) 2239 platform_device_unregister(pdev); 2240 return NULL; 2241 } 2242 EXPORT_SYMBOL(parport_pc_probe_port); 2243 2244 void parport_pc_unregister_port(struct parport *p) 2245 { 2246 struct parport_pc_private *priv = p->private_data; 2247 struct parport_operations *ops = p->ops; 2248 2249 parport_remove_port(p); 2250 spin_lock(&ports_lock); 2251 list_del_init(&priv->list); 2252 spin_unlock(&ports_lock); 2253 #if defined(CONFIG_PARPORT_PC_FIFO) && defined(HAS_DMA) 2254 if (p->dma != PARPORT_DMA_NONE) 2255 free_dma(p->dma); 2256 #endif 2257 if (p->irq != PARPORT_IRQ_NONE) 2258 free_irq(p->irq, p); 2259 release_region(p->base, 3); 2260 if (p->size > 3) 2261 release_region(p->base + 3, p->size - 3); 2262 if (p->modes & PARPORT_MODE_ECP) 2263 release_region(p->base_hi, 3); 2264 #if defined(CONFIG_PARPORT_PC_FIFO) && defined(HAS_DMA) 2265 if (priv->dma_buf) 2266 dma_free_coherent(p->physport->dev, PAGE_SIZE, 2267 priv->dma_buf, 2268 priv->dma_handle); 2269 #endif 2270 kfree(p->private_data); 2271 parport_del_port(p); 2272 kfree(ops); /* hope no-one cached it */ 2273 } 2274 EXPORT_SYMBOL(parport_pc_unregister_port); 2275 2276 #ifdef CONFIG_PCI 2277 2278 /* ITE support maintained by Rich Liu <richliu@poorman.org> */ 2279 static int sio_ite_8872_probe(struct pci_dev *pdev, int autoirq, int autodma, 2280 const struct parport_pc_via_data *via) 2281 { 2282 short inta_addr[6] = { 0x2A0, 0x2C0, 0x220, 0x240, 0x1E0 }; 2283 u32 ite8872set; 2284 u32 ite8872_lpt, ite8872_lpthi; 2285 u8 ite8872_irq, type; 2286 int irq; 2287 int i; 2288 2289 pr_debug("sio_ite_8872_probe()\n"); 2290 2291 /* make sure which one chip */ 2292 for (i = 0; i < 5; i++) { 2293 if (request_region(inta_addr[i], 32, "it887x")) { 2294 int test; 2295 pci_write_config_dword(pdev, 0x60, 2296 0xe5000000 | inta_addr[i]); 2297 pci_write_config_dword(pdev, 0x78, 2298 0x00000000 | inta_addr[i]); 2299 test = inb(inta_addr[i]); 2300 if (test != 0xff) 2301 break; 2302 release_region(inta_addr[i], 32); 2303 } 2304 } 2305 if (i >= 5) { 2306 pr_info("parport_pc: cannot find ITE8872 INTA\n"); 2307 return 0; 2308 } 2309 2310 type = inb(inta_addr[i] + 0x18); 2311 type &= 0x0f; 2312 2313 switch (type) { 2314 case 0x2: 2315 pr_info("parport_pc: ITE8871 found (1P)\n"); 2316 ite8872set = 0x64200000; 2317 break; 2318 case 0xa: 2319 pr_info("parport_pc: ITE8875 found (1P)\n"); 2320 ite8872set = 0x64200000; 2321 break; 2322 case 0xe: 2323 pr_info("parport_pc: ITE8872 found (2S1P)\n"); 2324 ite8872set = 0x64e00000; 2325 break; 2326 case 0x6: 2327 pr_info("parport_pc: ITE8873 found (1S)\n"); 2328 release_region(inta_addr[i], 32); 2329 return 0; 2330 case 0x8: 2331 pr_info("parport_pc: ITE8874 found (2S)\n"); 2332 release_region(inta_addr[i], 32); 2333 return 0; 2334 default: 2335 pr_info("parport_pc: unknown ITE887x\n"); 2336 pr_info("parport_pc: please mail 'lspci -nvv' output to Rich.Liu@ite.com.tw\n"); 2337 release_region(inta_addr[i], 32); 2338 return 0; 2339 } 2340 2341 pci_read_config_byte(pdev, 0x3c, &ite8872_irq); 2342 pci_read_config_dword(pdev, 0x1c, &ite8872_lpt); 2343 ite8872_lpt &= 0x0000ff00; 2344 pci_read_config_dword(pdev, 0x20, &ite8872_lpthi); 2345 ite8872_lpthi &= 0x0000ff00; 2346 pci_write_config_dword(pdev, 0x6c, 0xe3000000 | ite8872_lpt); 2347 pci_write_config_dword(pdev, 0x70, 0xe3000000 | ite8872_lpthi); 2348 pci_write_config_dword(pdev, 0x80, (ite8872_lpthi<<16) | ite8872_lpt); 2349 /* SET SPP&EPP , Parallel Port NO DMA , Enable All Function */ 2350 /* SET Parallel IRQ */ 2351 pci_write_config_dword(pdev, 0x9c, 2352 ite8872set | (ite8872_irq * 0x11111)); 2353 2354 pr_debug("ITE887x: The IRQ is %d\n", ite8872_irq); 2355 pr_debug("ITE887x: The PARALLEL I/O port is 0x%x\n", ite8872_lpt); 2356 pr_debug("ITE887x: The PARALLEL I/O porthi is 0x%x\n", ite8872_lpthi); 2357 2358 /* Let the user (or defaults) steer us away from interrupts */ 2359 irq = ite8872_irq; 2360 if (autoirq != PARPORT_IRQ_AUTO) 2361 irq = PARPORT_IRQ_NONE; 2362 2363 /* 2364 * Release the resource so that parport_pc_probe_port can get it. 2365 */ 2366 release_region(inta_addr[i], 32); 2367 if (parport_pc_probe_port(ite8872_lpt, ite8872_lpthi, 2368 irq, PARPORT_DMA_NONE, &pdev->dev, 0)) { 2369 pr_info("parport_pc: ITE 8872 parallel port: io=0x%X", 2370 ite8872_lpt); 2371 if (irq != PARPORT_IRQ_NONE) 2372 pr_cont(", irq=%d", irq); 2373 pr_cont("\n"); 2374 return 1; 2375 } 2376 2377 return 0; 2378 } 2379 2380 /* VIA 8231 support by Pavel Fedin <sonic_amiga@rambler.ru> 2381 based on VIA 686a support code by Jeff Garzik <jgarzik@pobox.com> */ 2382 static int parport_init_mode; 2383 2384 /* Data for two known VIA chips */ 2385 static struct parport_pc_via_data via_686a_data = { 2386 0x51, 2387 0x50, 2388 0x85, 2389 0x02, 2390 0xE2, 2391 0xF0, 2392 0xE6 2393 }; 2394 static struct parport_pc_via_data via_8231_data = { 2395 0x45, 2396 0x44, 2397 0x50, 2398 0x04, 2399 0xF2, 2400 0xFA, 2401 0xF6 2402 }; 2403 2404 static int sio_via_probe(struct pci_dev *pdev, int autoirq, int autodma, 2405 const struct parport_pc_via_data *via) 2406 { 2407 u8 tmp, tmp2, siofunc; 2408 u8 ppcontrol = 0; 2409 int dma, irq; 2410 unsigned port1, port2; 2411 unsigned have_epp = 0; 2412 2413 printk(KERN_DEBUG "parport_pc: VIA 686A/8231 detected\n"); 2414 2415 switch (parport_init_mode) { 2416 case 1: 2417 printk(KERN_DEBUG "parport_pc: setting SPP mode\n"); 2418 siofunc = VIA_FUNCTION_PARPORT_SPP; 2419 break; 2420 case 2: 2421 printk(KERN_DEBUG "parport_pc: setting PS/2 mode\n"); 2422 siofunc = VIA_FUNCTION_PARPORT_SPP; 2423 ppcontrol = VIA_PARPORT_BIDIR; 2424 break; 2425 case 3: 2426 printk(KERN_DEBUG "parport_pc: setting EPP mode\n"); 2427 siofunc = VIA_FUNCTION_PARPORT_EPP; 2428 ppcontrol = VIA_PARPORT_BIDIR; 2429 have_epp = 1; 2430 break; 2431 case 4: 2432 printk(KERN_DEBUG "parport_pc: setting ECP mode\n"); 2433 siofunc = VIA_FUNCTION_PARPORT_ECP; 2434 ppcontrol = VIA_PARPORT_BIDIR; 2435 break; 2436 case 5: 2437 printk(KERN_DEBUG "parport_pc: setting EPP+ECP mode\n"); 2438 siofunc = VIA_FUNCTION_PARPORT_ECP; 2439 ppcontrol = VIA_PARPORT_BIDIR|VIA_PARPORT_ECPEPP; 2440 have_epp = 1; 2441 break; 2442 default: 2443 printk(KERN_DEBUG "parport_pc: probing current configuration\n"); 2444 siofunc = VIA_FUNCTION_PROBE; 2445 break; 2446 } 2447 /* 2448 * unlock super i/o configuration 2449 */ 2450 pci_read_config_byte(pdev, via->via_pci_superio_config_reg, &tmp); 2451 tmp |= via->via_pci_superio_config_data; 2452 pci_write_config_byte(pdev, via->via_pci_superio_config_reg, tmp); 2453 2454 /* Bits 1-0: Parallel Port Mode / Enable */ 2455 outb(via->viacfg_function, VIA_CONFIG_INDEX); 2456 tmp = inb(VIA_CONFIG_DATA); 2457 /* Bit 5: EPP+ECP enable; bit 7: PS/2 bidirectional port enable */ 2458 outb(via->viacfg_parport_control, VIA_CONFIG_INDEX); 2459 tmp2 = inb(VIA_CONFIG_DATA); 2460 if (siofunc == VIA_FUNCTION_PROBE) { 2461 siofunc = tmp & VIA_FUNCTION_PARPORT_DISABLE; 2462 ppcontrol = tmp2; 2463 } else { 2464 tmp &= ~VIA_FUNCTION_PARPORT_DISABLE; 2465 tmp |= siofunc; 2466 outb(via->viacfg_function, VIA_CONFIG_INDEX); 2467 outb(tmp, VIA_CONFIG_DATA); 2468 tmp2 &= ~(VIA_PARPORT_BIDIR|VIA_PARPORT_ECPEPP); 2469 tmp2 |= ppcontrol; 2470 outb(via->viacfg_parport_control, VIA_CONFIG_INDEX); 2471 outb(tmp2, VIA_CONFIG_DATA); 2472 } 2473 2474 /* Parallel Port I/O Base Address, bits 9-2 */ 2475 outb(via->viacfg_parport_base, VIA_CONFIG_INDEX); 2476 port1 = inb(VIA_CONFIG_DATA) << 2; 2477 2478 printk(KERN_DEBUG "parport_pc: Current parallel port base: 0x%X\n", 2479 port1); 2480 if (port1 == 0x3BC && have_epp) { 2481 outb(via->viacfg_parport_base, VIA_CONFIG_INDEX); 2482 outb((0x378 >> 2), VIA_CONFIG_DATA); 2483 printk(KERN_DEBUG "parport_pc: Parallel port base changed to 0x378\n"); 2484 port1 = 0x378; 2485 } 2486 2487 /* 2488 * lock super i/o configuration 2489 */ 2490 pci_read_config_byte(pdev, via->via_pci_superio_config_reg, &tmp); 2491 tmp &= ~via->via_pci_superio_config_data; 2492 pci_write_config_byte(pdev, via->via_pci_superio_config_reg, tmp); 2493 2494 if (siofunc == VIA_FUNCTION_PARPORT_DISABLE) { 2495 pr_info("parport_pc: VIA parallel port disabled in BIOS\n"); 2496 return 0; 2497 } 2498 2499 /* Bits 7-4: PnP Routing for Parallel Port IRQ */ 2500 pci_read_config_byte(pdev, via->via_pci_parport_irq_reg, &tmp); 2501 irq = ((tmp & VIA_IRQCONTROL_PARALLEL) >> 4); 2502 2503 if (siofunc == VIA_FUNCTION_PARPORT_ECP) { 2504 /* Bits 3-2: PnP Routing for Parallel Port DMA */ 2505 pci_read_config_byte(pdev, via->via_pci_parport_dma_reg, &tmp); 2506 dma = ((tmp & VIA_DMACONTROL_PARALLEL) >> 2); 2507 } else 2508 /* if ECP not enabled, DMA is not enabled, assumed 2509 bogus 'dma' value */ 2510 dma = PARPORT_DMA_NONE; 2511 2512 /* Let the user (or defaults) steer us away from interrupts and DMA */ 2513 if (autoirq == PARPORT_IRQ_NONE) { 2514 irq = PARPORT_IRQ_NONE; 2515 dma = PARPORT_DMA_NONE; 2516 } 2517 if (autodma == PARPORT_DMA_NONE) 2518 dma = PARPORT_DMA_NONE; 2519 2520 switch (port1) { 2521 case 0x3bc: 2522 port2 = 0x7bc; break; 2523 case 0x378: 2524 port2 = 0x778; break; 2525 case 0x278: 2526 port2 = 0x678; break; 2527 default: 2528 pr_info("parport_pc: Weird VIA parport base 0x%X, ignoring\n", 2529 port1); 2530 return 0; 2531 } 2532 2533 /* filter bogus IRQs */ 2534 switch (irq) { 2535 case 0: 2536 case 2: 2537 case 8: 2538 case 13: 2539 irq = PARPORT_IRQ_NONE; 2540 break; 2541 2542 default: /* do nothing */ 2543 break; 2544 } 2545 2546 /* finally, do the probe with values obtained */ 2547 if (parport_pc_probe_port(port1, port2, irq, dma, &pdev->dev, 0)) { 2548 pr_info("parport_pc: VIA parallel port: io=0x%X", port1); 2549 if (irq != PARPORT_IRQ_NONE) 2550 pr_cont(", irq=%d", irq); 2551 if (dma != PARPORT_DMA_NONE) 2552 pr_cont(", dma=%d", dma); 2553 pr_cont("\n"); 2554 return 1; 2555 } 2556 2557 pr_warn("parport_pc: Strange, can't probe VIA parallel port: io=0x%X, irq=%d, dma=%d\n", 2558 port1, irq, dma); 2559 return 0; 2560 } 2561 2562 2563 enum parport_pc_sio_types { 2564 sio_via_686a = 0, /* Via VT82C686A motherboard Super I/O */ 2565 sio_via_8231, /* Via VT8231 south bridge integrated Super IO */ 2566 sio_ite_8872, 2567 last_sio 2568 }; 2569 2570 /* each element directly indexed from enum list, above */ 2571 static struct parport_pc_superio { 2572 int (*probe) (struct pci_dev *pdev, int autoirq, int autodma, 2573 const struct parport_pc_via_data *via); 2574 const struct parport_pc_via_data *via; 2575 } parport_pc_superio_info[] = { 2576 { sio_via_probe, &via_686a_data, }, 2577 { sio_via_probe, &via_8231_data, }, 2578 { sio_ite_8872_probe, NULL, }, 2579 }; 2580 2581 enum parport_pc_pci_cards { 2582 siig_1p_10x = last_sio, 2583 siig_2p_10x, 2584 siig_1p_20x, 2585 siig_2p_20x, 2586 lava_parallel, 2587 lava_parallel_dual_a, 2588 lava_parallel_dual_b, 2589 boca_ioppar, 2590 plx_9050, 2591 timedia_4006a, 2592 timedia_4014, 2593 timedia_4008a, 2594 timedia_4018, 2595 timedia_9018a, 2596 syba_2p_epp, 2597 syba_1p_ecp, 2598 titan_010l, 2599 avlab_1p, 2600 avlab_2p, 2601 oxsemi_952, 2602 oxsemi_954, 2603 oxsemi_840, 2604 oxsemi_pcie_pport, 2605 aks_0100, 2606 mobility_pp, 2607 netmos_9705, 2608 netmos_9715, 2609 netmos_9755, 2610 netmos_9805, 2611 netmos_9815, 2612 netmos_9901, 2613 netmos_9865, 2614 quatech_sppxp100, 2615 wch_ch382l, 2616 }; 2617 2618 2619 /* each element directly indexed from enum list, above 2620 * (but offset by last_sio) */ 2621 static struct parport_pc_pci { 2622 int numports; 2623 struct { /* BAR (base address registers) numbers in the config 2624 space header */ 2625 int lo; 2626 int hi; 2627 /* -1 if not there, >6 for offset-method (max BAR is 6) */ 2628 } addr[4]; 2629 2630 /* If set, this is called immediately after pci_enable_device. 2631 * If it returns non-zero, no probing will take place and the 2632 * ports will not be used. */ 2633 int (*preinit_hook) (struct pci_dev *pdev, int autoirq, int autodma); 2634 2635 /* If set, this is called after probing for ports. If 'failed' 2636 * is non-zero we couldn't use any of the ports. */ 2637 void (*postinit_hook) (struct pci_dev *pdev, int failed); 2638 } cards[] = { 2639 /* siig_1p_10x */ { 1, { { 2, 3 }, } }, 2640 /* siig_2p_10x */ { 2, { { 2, 3 }, { 4, 5 }, } }, 2641 /* siig_1p_20x */ { 1, { { 0, 1 }, } }, 2642 /* siig_2p_20x */ { 2, { { 0, 1 }, { 2, 3 }, } }, 2643 /* lava_parallel */ { 1, { { 0, -1 }, } }, 2644 /* lava_parallel_dual_a */ { 1, { { 0, -1 }, } }, 2645 /* lava_parallel_dual_b */ { 1, { { 0, -1 }, } }, 2646 /* boca_ioppar */ { 1, { { 0, -1 }, } }, 2647 /* plx_9050 */ { 2, { { 4, -1 }, { 5, -1 }, } }, 2648 /* timedia_4006a */ { 1, { { 0, -1 }, } }, 2649 /* timedia_4014 */ { 2, { { 0, -1 }, { 2, -1 }, } }, 2650 /* timedia_4008a */ { 1, { { 0, 1 }, } }, 2651 /* timedia_4018 */ { 2, { { 0, 1 }, { 2, 3 }, } }, 2652 /* timedia_9018a */ { 2, { { 0, 1 }, { 2, 3 }, } }, 2653 /* SYBA uses fixed offsets in 2654 a 1K io window */ 2655 /* syba_2p_epp AP138B */ { 2, { { 0, 0x078 }, { 0, 0x178 }, } }, 2656 /* syba_1p_ecp W83787 */ { 1, { { 0, 0x078 }, } }, 2657 /* titan_010l */ { 1, { { 3, -1 }, } }, 2658 /* avlab_1p */ { 1, { { 0, 1}, } }, 2659 /* avlab_2p */ { 2, { { 0, 1}, { 2, 3 },} }, 2660 /* The Oxford Semi cards are unusual: 954 doesn't support ECP, 2661 * and 840 locks up if you write 1 to bit 2! */ 2662 /* oxsemi_952 */ { 1, { { 0, 1 }, } }, 2663 /* oxsemi_954 */ { 1, { { 0, -1 }, } }, 2664 /* oxsemi_840 */ { 1, { { 0, 1 }, } }, 2665 /* oxsemi_pcie_pport */ { 1, { { 0, 1 }, } }, 2666 /* aks_0100 */ { 1, { { 0, -1 }, } }, 2667 /* mobility_pp */ { 1, { { 0, 1 }, } }, 2668 2669 /* The netmos entries below are untested */ 2670 /* netmos_9705 */ { 1, { { 0, -1 }, } }, 2671 /* netmos_9715 */ { 2, { { 0, 1 }, { 2, 3 },} }, 2672 /* netmos_9755 */ { 2, { { 0, 1 }, { 2, 3 },} }, 2673 /* netmos_9805 */ { 1, { { 0, 1 }, } }, 2674 /* netmos_9815 */ { 2, { { 0, 1 }, { 2, 3 }, } }, 2675 /* netmos_9901 */ { 1, { { 0, -1 }, } }, 2676 /* netmos_9865 */ { 1, { { 0, -1 }, } }, 2677 /* quatech_sppxp100 */ { 1, { { 0, 1 }, } }, 2678 /* wch_ch382l */ { 1, { { 2, -1 }, } }, 2679 }; 2680 2681 static const struct pci_device_id parport_pc_pci_tbl[] = { 2682 /* Super-IO onboard chips */ 2683 { 0x1106, 0x0686, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sio_via_686a }, 2684 { 0x1106, 0x8231, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sio_via_8231 }, 2685 { PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8872, 2686 PCI_ANY_ID, PCI_ANY_ID, 0, 0, sio_ite_8872 }, 2687 2688 /* PCI cards */ 2689 { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1P_10x, 2690 PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_1p_10x }, 2691 { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2P_10x, 2692 PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2p_10x }, 2693 { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1P_20x, 2694 PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_1p_20x }, 2695 { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2P_20x, 2696 PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2p_20x }, 2697 { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_PARALLEL, 2698 PCI_ANY_ID, PCI_ANY_ID, 0, 0, lava_parallel }, 2699 { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_DUAL_PAR_A, 2700 PCI_ANY_ID, PCI_ANY_ID, 0, 0, lava_parallel_dual_a }, 2701 { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_DUAL_PAR_B, 2702 PCI_ANY_ID, PCI_ANY_ID, 0, 0, lava_parallel_dual_b }, 2703 { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_BOCA_IOPPAR, 2704 PCI_ANY_ID, PCI_ANY_ID, 0, 0, boca_ioppar }, 2705 { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050, 2706 PCI_SUBVENDOR_ID_EXSYS, PCI_SUBDEVICE_ID_EXSYS_4014, 0, 0, plx_9050 }, 2707 /* PCI_VENDOR_ID_TIMEDIA/SUNIX has many differing cards ...*/ 2708 { 0x1409, 0x7268, 0x1409, 0x0101, 0, 0, timedia_4006a }, 2709 { 0x1409, 0x7268, 0x1409, 0x0102, 0, 0, timedia_4014 }, 2710 { 0x1409, 0x7268, 0x1409, 0x0103, 0, 0, timedia_4008a }, 2711 { 0x1409, 0x7268, 0x1409, 0x0104, 0, 0, timedia_4018 }, 2712 { 0x1409, 0x7268, 0x1409, 0x9018, 0, 0, timedia_9018a }, 2713 { PCI_VENDOR_ID_SYBA, PCI_DEVICE_ID_SYBA_2P_EPP, 2714 PCI_ANY_ID, PCI_ANY_ID, 0, 0, syba_2p_epp }, 2715 { PCI_VENDOR_ID_SYBA, PCI_DEVICE_ID_SYBA_1P_ECP, 2716 PCI_ANY_ID, PCI_ANY_ID, 0, 0, syba_1p_ecp }, 2717 { PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_010L, 2718 PCI_ANY_ID, PCI_ANY_ID, 0, 0, titan_010l }, 2719 /* PCI_VENDOR_ID_AVLAB/Intek21 has another bunch of cards ...*/ 2720 /* AFAVLAB_TK9902 */ 2721 { 0x14db, 0x2120, PCI_ANY_ID, PCI_ANY_ID, 0, 0, avlab_1p}, 2722 { 0x14db, 0x2121, PCI_ANY_ID, PCI_ANY_ID, 0, 0, avlab_2p}, 2723 { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI952PP, 2724 PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_952 }, 2725 { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI954PP, 2726 PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_954 }, 2727 { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_12PCI840, 2728 PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_840 }, 2729 { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe840, 2730 PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport }, 2731 { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe840_G, 2732 PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport }, 2733 { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_0, 2734 PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport }, 2735 { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_0_G, 2736 PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport }, 2737 { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_1, 2738 PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport }, 2739 { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_1_G, 2740 PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport }, 2741 { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_1_U, 2742 PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport }, 2743 { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_1_GU, 2744 PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport }, 2745 { PCI_VENDOR_ID_AKS, PCI_DEVICE_ID_AKS_ALADDINCARD, 2746 PCI_ANY_ID, PCI_ANY_ID, 0, 0, aks_0100 }, 2747 { 0x14f2, 0x0121, PCI_ANY_ID, PCI_ANY_ID, 0, 0, mobility_pp }, 2748 /* NetMos communication controllers */ 2749 { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9705, 2750 PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9705 }, 2751 { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9715, 2752 PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9715 }, 2753 { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9755, 2754 PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9755 }, 2755 { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9805, 2756 PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9805 }, 2757 { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9815, 2758 PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9815 }, 2759 { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9901, 2760 0xA000, 0x2000, 0, 0, netmos_9901 }, 2761 { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9865, 2762 0xA000, 0x1000, 0, 0, netmos_9865 }, 2763 { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9865, 2764 0xA000, 0x2000, 0, 0, netmos_9865 }, 2765 /* Quatech SPPXP-100 Parallel port PCI ExpressCard */ 2766 { PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_SPPXP_100, 2767 PCI_ANY_ID, PCI_ANY_ID, 0, 0, quatech_sppxp100 }, 2768 /* WCH CH382L PCI-E single parallel port card */ 2769 { 0x1c00, 0x3050, 0x1c00, 0x3050, 0, 0, wch_ch382l }, 2770 { 0, } /* terminate list */ 2771 }; 2772 MODULE_DEVICE_TABLE(pci, parport_pc_pci_tbl); 2773 2774 struct pci_parport_data { 2775 int num; 2776 struct parport *ports[2]; 2777 }; 2778 2779 static int parport_pc_pci_probe(struct pci_dev *dev, 2780 const struct pci_device_id *id) 2781 { 2782 int err, count, n, i = id->driver_data; 2783 struct pci_parport_data *data; 2784 2785 if (i < last_sio) 2786 /* This is an onboard Super-IO and has already been probed */ 2787 return 0; 2788 2789 /* This is a PCI card */ 2790 i -= last_sio; 2791 count = 0; 2792 err = pci_enable_device(dev); 2793 if (err) 2794 return err; 2795 2796 data = kmalloc(sizeof(struct pci_parport_data), GFP_KERNEL); 2797 if (!data) 2798 return -ENOMEM; 2799 2800 if (cards[i].preinit_hook && 2801 cards[i].preinit_hook(dev, PARPORT_IRQ_NONE, PARPORT_DMA_NONE)) { 2802 kfree(data); 2803 return -ENODEV; 2804 } 2805 2806 for (n = 0; n < cards[i].numports; n++) { 2807 int lo = cards[i].addr[n].lo; 2808 int hi = cards[i].addr[n].hi; 2809 int irq; 2810 unsigned long io_lo, io_hi; 2811 io_lo = pci_resource_start(dev, lo); 2812 io_hi = 0; 2813 if ((hi >= 0) && (hi <= 6)) 2814 io_hi = pci_resource_start(dev, hi); 2815 else if (hi > 6) 2816 io_lo += hi; /* Reinterpret the meaning of 2817 "hi" as an offset (see SYBA 2818 def.) */ 2819 /* TODO: test if sharing interrupts works */ 2820 irq = dev->irq; 2821 if (irq == IRQ_NONE) { 2822 printk(KERN_DEBUG "PCI parallel port detected: %04x:%04x, I/O at %#lx(%#lx)\n", 2823 id->vendor, id->device, io_lo, io_hi); 2824 irq = PARPORT_IRQ_NONE; 2825 } else { 2826 printk(KERN_DEBUG "PCI parallel port detected: %04x:%04x, I/O at %#lx(%#lx), IRQ %d\n", 2827 id->vendor, id->device, io_lo, io_hi, irq); 2828 } 2829 data->ports[count] = 2830 parport_pc_probe_port(io_lo, io_hi, irq, 2831 PARPORT_DMA_NONE, &dev->dev, 2832 IRQF_SHARED); 2833 if (data->ports[count]) 2834 count++; 2835 } 2836 2837 data->num = count; 2838 2839 if (cards[i].postinit_hook) 2840 cards[i].postinit_hook(dev, count == 0); 2841 2842 if (count) { 2843 pci_set_drvdata(dev, data); 2844 return 0; 2845 } 2846 2847 kfree(data); 2848 2849 return -ENODEV; 2850 } 2851 2852 static void parport_pc_pci_remove(struct pci_dev *dev) 2853 { 2854 struct pci_parport_data *data = pci_get_drvdata(dev); 2855 int i; 2856 2857 if (data) { 2858 for (i = data->num - 1; i >= 0; i--) 2859 parport_pc_unregister_port(data->ports[i]); 2860 2861 kfree(data); 2862 } 2863 } 2864 2865 static struct pci_driver parport_pc_pci_driver = { 2866 .name = "parport_pc", 2867 .id_table = parport_pc_pci_tbl, 2868 .probe = parport_pc_pci_probe, 2869 .remove = parport_pc_pci_remove, 2870 }; 2871 2872 static int __init parport_pc_init_superio(int autoirq, int autodma) 2873 { 2874 const struct pci_device_id *id; 2875 struct pci_dev *pdev = NULL; 2876 int ret = 0; 2877 2878 for_each_pci_dev(pdev) { 2879 id = pci_match_id(parport_pc_pci_tbl, pdev); 2880 if (id == NULL || id->driver_data >= last_sio) 2881 continue; 2882 2883 if (parport_pc_superio_info[id->driver_data].probe( 2884 pdev, autoirq, autodma, 2885 parport_pc_superio_info[id->driver_data].via)) { 2886 ret++; 2887 } 2888 } 2889 2890 return ret; /* number of devices found */ 2891 } 2892 #else 2893 static struct pci_driver parport_pc_pci_driver; 2894 static int __init parport_pc_init_superio(int autoirq, int autodma) 2895 { 2896 return 0; 2897 } 2898 #endif /* CONFIG_PCI */ 2899 2900 #ifdef CONFIG_PNP 2901 2902 static const struct pnp_device_id parport_pc_pnp_tbl[] = { 2903 /* Standard LPT Printer Port */ 2904 {.id = "PNP0400", .driver_data = 0}, 2905 /* ECP Printer Port */ 2906 {.id = "PNP0401", .driver_data = 0}, 2907 { } 2908 }; 2909 2910 MODULE_DEVICE_TABLE(pnp, parport_pc_pnp_tbl); 2911 2912 static int parport_pc_pnp_probe(struct pnp_dev *dev, 2913 const struct pnp_device_id *id) 2914 { 2915 struct parport *pdata; 2916 unsigned long io_lo, io_hi; 2917 int dma, irq; 2918 2919 if (pnp_port_valid(dev, 0) && 2920 !(pnp_port_flags(dev, 0) & IORESOURCE_DISABLED)) { 2921 io_lo = pnp_port_start(dev, 0); 2922 } else 2923 return -EINVAL; 2924 2925 if (pnp_port_valid(dev, 1) && 2926 !(pnp_port_flags(dev, 1) & IORESOURCE_DISABLED)) { 2927 io_hi = pnp_port_start(dev, 1); 2928 } else 2929 io_hi = 0; 2930 2931 if (pnp_irq_valid(dev, 0) && 2932 !(pnp_irq_flags(dev, 0) & IORESOURCE_DISABLED)) { 2933 irq = pnp_irq(dev, 0); 2934 } else 2935 irq = PARPORT_IRQ_NONE; 2936 2937 if (pnp_dma_valid(dev, 0) && 2938 !(pnp_dma_flags(dev, 0) & IORESOURCE_DISABLED)) { 2939 dma = pnp_dma(dev, 0); 2940 } else 2941 dma = PARPORT_DMA_NONE; 2942 2943 dev_info(&dev->dev, "reported by %s\n", dev->protocol->name); 2944 pdata = parport_pc_probe_port(io_lo, io_hi, irq, dma, &dev->dev, 0); 2945 if (pdata == NULL) 2946 return -ENODEV; 2947 2948 pnp_set_drvdata(dev, pdata); 2949 return 0; 2950 } 2951 2952 static void parport_pc_pnp_remove(struct pnp_dev *dev) 2953 { 2954 struct parport *pdata = (struct parport *)pnp_get_drvdata(dev); 2955 if (!pdata) 2956 return; 2957 2958 parport_pc_unregister_port(pdata); 2959 } 2960 2961 /* we only need the pnp layer to activate the device, at least for now */ 2962 static struct pnp_driver parport_pc_pnp_driver = { 2963 .name = "parport_pc", 2964 .id_table = parport_pc_pnp_tbl, 2965 .probe = parport_pc_pnp_probe, 2966 .remove = parport_pc_pnp_remove, 2967 }; 2968 2969 #else 2970 static struct pnp_driver parport_pc_pnp_driver; 2971 #endif /* CONFIG_PNP */ 2972 2973 static int parport_pc_platform_probe(struct platform_device *pdev) 2974 { 2975 /* Always succeed, the actual probing is done in 2976 * parport_pc_probe_port(). */ 2977 return 0; 2978 } 2979 2980 static struct platform_driver parport_pc_platform_driver = { 2981 .driver = { 2982 .name = "parport_pc", 2983 }, 2984 .probe = parport_pc_platform_probe, 2985 }; 2986 2987 /* This is called by parport_pc_find_nonpci_ports (in asm/parport.h) */ 2988 static int __attribute__((unused)) 2989 parport_pc_find_isa_ports(int autoirq, int autodma) 2990 { 2991 int count = 0; 2992 2993 if (parport_pc_probe_port(0x3bc, 0x7bc, autoirq, autodma, NULL, 0)) 2994 count++; 2995 if (parport_pc_probe_port(0x378, 0x778, autoirq, autodma, NULL, 0)) 2996 count++; 2997 if (parport_pc_probe_port(0x278, 0x678, autoirq, autodma, NULL, 0)) 2998 count++; 2999 3000 return count; 3001 } 3002 3003 /* This function is called by parport_pc_init if the user didn't 3004 * specify any ports to probe. Its job is to find some ports. Order 3005 * is important here -- we want ISA ports to be registered first, 3006 * followed by PCI cards (for least surprise), but before that we want 3007 * to do chipset-specific tests for some onboard ports that we know 3008 * about. 3009 * 3010 * autoirq is PARPORT_IRQ_NONE, PARPORT_IRQ_AUTO, or PARPORT_IRQ_PROBEONLY 3011 * autodma is PARPORT_DMA_NONE or PARPORT_DMA_AUTO 3012 */ 3013 static void __init parport_pc_find_ports(int autoirq, int autodma) 3014 { 3015 int count = 0, err; 3016 3017 #ifdef CONFIG_PARPORT_PC_SUPERIO 3018 detect_and_report_it87(); 3019 detect_and_report_winbond(); 3020 detect_and_report_smsc(); 3021 #endif 3022 3023 /* Onboard SuperIO chipsets that show themselves on the PCI bus. */ 3024 count += parport_pc_init_superio(autoirq, autodma); 3025 3026 /* PnP ports, skip detection if SuperIO already found them */ 3027 if (!count) { 3028 err = pnp_register_driver(&parport_pc_pnp_driver); 3029 if (!err) 3030 pnp_registered_parport = 1; 3031 } 3032 3033 /* ISA ports and whatever (see asm/parport.h). */ 3034 parport_pc_find_nonpci_ports(autoirq, autodma); 3035 3036 err = pci_register_driver(&parport_pc_pci_driver); 3037 if (!err) 3038 pci_registered_parport = 1; 3039 } 3040 3041 /* 3042 * Piles of crap below pretend to be a parser for module and kernel 3043 * parameters. Say "thank you" to whoever had come up with that 3044 * syntax and keep in mind that code below is a cleaned up version. 3045 */ 3046 3047 static int __initdata io[PARPORT_PC_MAX_PORTS+1] = { 3048 [0 ... PARPORT_PC_MAX_PORTS] = 0 3049 }; 3050 static int __initdata io_hi[PARPORT_PC_MAX_PORTS+1] = { 3051 [0 ... PARPORT_PC_MAX_PORTS] = PARPORT_IOHI_AUTO 3052 }; 3053 static int __initdata dmaval[PARPORT_PC_MAX_PORTS] = { 3054 [0 ... PARPORT_PC_MAX_PORTS-1] = PARPORT_DMA_NONE 3055 }; 3056 static int __initdata irqval[PARPORT_PC_MAX_PORTS] = { 3057 [0 ... PARPORT_PC_MAX_PORTS-1] = PARPORT_IRQ_PROBEONLY 3058 }; 3059 3060 static int __init parport_parse_param(const char *s, int *val, 3061 int automatic, int none, int nofifo) 3062 { 3063 if (!s) 3064 return 0; 3065 if (!strncmp(s, "auto", 4)) 3066 *val = automatic; 3067 else if (!strncmp(s, "none", 4)) 3068 *val = none; 3069 else if (nofifo && !strncmp(s, "nofifo", 6)) 3070 *val = nofifo; 3071 else { 3072 char *ep; 3073 unsigned long r = simple_strtoul(s, &ep, 0); 3074 if (ep != s) 3075 *val = r; 3076 else { 3077 pr_err("parport: bad specifier `%s'\n", s); 3078 return -1; 3079 } 3080 } 3081 return 0; 3082 } 3083 3084 static int __init parport_parse_irq(const char *irqstr, int *val) 3085 { 3086 return parport_parse_param(irqstr, val, PARPORT_IRQ_AUTO, 3087 PARPORT_IRQ_NONE, 0); 3088 } 3089 3090 static int __init parport_parse_dma(const char *dmastr, int *val) 3091 { 3092 return parport_parse_param(dmastr, val, PARPORT_DMA_AUTO, 3093 PARPORT_DMA_NONE, PARPORT_DMA_NOFIFO); 3094 } 3095 3096 #ifdef CONFIG_PCI 3097 static int __init parport_init_mode_setup(char *str) 3098 { 3099 printk(KERN_DEBUG "parport_pc.c: Specified parameter parport_init_mode=%s\n", 3100 str); 3101 3102 if (!strcmp(str, "spp")) 3103 parport_init_mode = 1; 3104 if (!strcmp(str, "ps2")) 3105 parport_init_mode = 2; 3106 if (!strcmp(str, "epp")) 3107 parport_init_mode = 3; 3108 if (!strcmp(str, "ecp")) 3109 parport_init_mode = 4; 3110 if (!strcmp(str, "ecpepp")) 3111 parport_init_mode = 5; 3112 return 1; 3113 } 3114 #endif 3115 3116 #ifdef MODULE 3117 static char *irq[PARPORT_PC_MAX_PORTS]; 3118 static char *dma[PARPORT_PC_MAX_PORTS]; 3119 3120 MODULE_PARM_DESC(io, "Base I/O address (SPP regs)"); 3121 module_param_hw_array(io, int, ioport, NULL, 0); 3122 MODULE_PARM_DESC(io_hi, "Base I/O address (ECR)"); 3123 module_param_hw_array(io_hi, int, ioport, NULL, 0); 3124 MODULE_PARM_DESC(irq, "IRQ line"); 3125 module_param_hw_array(irq, charp, irq, NULL, 0); 3126 MODULE_PARM_DESC(dma, "DMA channel"); 3127 module_param_hw_array(dma, charp, dma, NULL, 0); 3128 #if defined(CONFIG_PARPORT_PC_SUPERIO) || \ 3129 (defined(CONFIG_PARPORT_1284) && defined(CONFIG_PARPORT_PC_FIFO)) 3130 MODULE_PARM_DESC(verbose_probing, "Log chit-chat during initialisation"); 3131 module_param(verbose_probing, int, 0644); 3132 #endif 3133 #ifdef CONFIG_PCI 3134 static char *init_mode; 3135 MODULE_PARM_DESC(init_mode, 3136 "Initialise mode for VIA VT8231 port (spp, ps2, epp, ecp or ecpepp)"); 3137 module_param(init_mode, charp, 0); 3138 #endif 3139 3140 static int __init parse_parport_params(void) 3141 { 3142 unsigned int i; 3143 int val; 3144 3145 #ifdef CONFIG_PCI 3146 if (init_mode) 3147 parport_init_mode_setup(init_mode); 3148 #endif 3149 3150 for (i = 0; i < PARPORT_PC_MAX_PORTS && io[i]; i++) { 3151 if (parport_parse_irq(irq[i], &val)) 3152 return 1; 3153 irqval[i] = val; 3154 if (parport_parse_dma(dma[i], &val)) 3155 return 1; 3156 dmaval[i] = val; 3157 } 3158 if (!io[0]) { 3159 /* The user can make us use any IRQs or DMAs we find. */ 3160 if (irq[0] && !parport_parse_irq(irq[0], &val)) 3161 switch (val) { 3162 case PARPORT_IRQ_NONE: 3163 case PARPORT_IRQ_AUTO: 3164 irqval[0] = val; 3165 break; 3166 default: 3167 pr_warn("parport_pc: irq specified without base address. Use 'io=' to specify one\n"); 3168 } 3169 3170 if (dma[0] && !parport_parse_dma(dma[0], &val)) 3171 switch (val) { 3172 case PARPORT_DMA_NONE: 3173 case PARPORT_DMA_AUTO: 3174 dmaval[0] = val; 3175 break; 3176 default: 3177 pr_warn("parport_pc: dma specified without base address. Use 'io=' to specify one\n"); 3178 } 3179 } 3180 return 0; 3181 } 3182 3183 #else 3184 3185 static int parport_setup_ptr __initdata; 3186 3187 /* 3188 * Acceptable parameters: 3189 * 3190 * parport=0 3191 * parport=auto 3192 * parport=0xBASE[,IRQ[,DMA]] 3193 * 3194 * IRQ/DMA may be numeric or 'auto' or 'none' 3195 */ 3196 static int __init parport_setup(char *str) 3197 { 3198 char *endptr; 3199 char *sep; 3200 int val; 3201 3202 if (!str || !*str || (*str == '0' && !*(str+1))) { 3203 /* Disable parport if "parport=0" in cmdline */ 3204 io[0] = PARPORT_DISABLE; 3205 return 1; 3206 } 3207 3208 if (!strncmp(str, "auto", 4)) { 3209 irqval[0] = PARPORT_IRQ_AUTO; 3210 dmaval[0] = PARPORT_DMA_AUTO; 3211 return 1; 3212 } 3213 3214 val = simple_strtoul(str, &endptr, 0); 3215 if (endptr == str) { 3216 pr_warn("parport=%s not understood\n", str); 3217 return 1; 3218 } 3219 3220 if (parport_setup_ptr == PARPORT_PC_MAX_PORTS) { 3221 pr_err("parport=%s ignored, too many ports\n", str); 3222 return 1; 3223 } 3224 3225 io[parport_setup_ptr] = val; 3226 irqval[parport_setup_ptr] = PARPORT_IRQ_NONE; 3227 dmaval[parport_setup_ptr] = PARPORT_DMA_NONE; 3228 3229 sep = strchr(str, ','); 3230 if (sep++) { 3231 if (parport_parse_irq(sep, &val)) 3232 return 1; 3233 irqval[parport_setup_ptr] = val; 3234 sep = strchr(sep, ','); 3235 if (sep++) { 3236 if (parport_parse_dma(sep, &val)) 3237 return 1; 3238 dmaval[parport_setup_ptr] = val; 3239 } 3240 } 3241 parport_setup_ptr++; 3242 return 1; 3243 } 3244 3245 static int __init parse_parport_params(void) 3246 { 3247 return io[0] == PARPORT_DISABLE; 3248 } 3249 3250 __setup("parport=", parport_setup); 3251 3252 /* 3253 * Acceptable parameters: 3254 * 3255 * parport_init_mode=[spp|ps2|epp|ecp|ecpepp] 3256 */ 3257 #ifdef CONFIG_PCI 3258 __setup("parport_init_mode=", parport_init_mode_setup); 3259 #endif 3260 #endif 3261 3262 /* "Parser" ends here */ 3263 3264 static int __init parport_pc_init(void) 3265 { 3266 int err; 3267 3268 if (parse_parport_params()) 3269 return -EINVAL; 3270 3271 err = platform_driver_register(&parport_pc_platform_driver); 3272 if (err) 3273 return err; 3274 3275 if (io[0]) { 3276 int i; 3277 /* Only probe the ports we were given. */ 3278 user_specified = 1; 3279 for (i = 0; i < PARPORT_PC_MAX_PORTS; i++) { 3280 if (!io[i]) 3281 break; 3282 if (io_hi[i] == PARPORT_IOHI_AUTO) 3283 io_hi[i] = 0x400 + io[i]; 3284 parport_pc_probe_port(io[i], io_hi[i], 3285 irqval[i], dmaval[i], NULL, 0); 3286 } 3287 } else 3288 parport_pc_find_ports(irqval[0], dmaval[0]); 3289 3290 return 0; 3291 } 3292 3293 static void __exit parport_pc_exit(void) 3294 { 3295 if (pci_registered_parport) 3296 pci_unregister_driver(&parport_pc_pci_driver); 3297 if (pnp_registered_parport) 3298 pnp_unregister_driver(&parport_pc_pnp_driver); 3299 platform_driver_unregister(&parport_pc_platform_driver); 3300 3301 while (!list_empty(&ports_list)) { 3302 struct parport_pc_private *priv; 3303 struct parport *port; 3304 struct device *dev; 3305 priv = list_entry(ports_list.next, 3306 struct parport_pc_private, list); 3307 port = priv->port; 3308 dev = port->dev; 3309 parport_pc_unregister_port(port); 3310 if (dev && dev->bus == &platform_bus_type) 3311 platform_device_unregister(to_platform_device(dev)); 3312 } 3313 } 3314 3315 MODULE_AUTHOR("Phil Blundell, Tim Waugh, others"); 3316 MODULE_DESCRIPTION("PC-style parallel port driver"); 3317 MODULE_LICENSE("GPL"); 3318 module_init(parport_pc_init) 3319 module_exit(parport_pc_exit) 3320