1 /* National Semiconductor NS87560UBD Super I/O controller used in 2 * HP [BCJ]x000 workstations. 3 * 4 * This chip is a horrid piece of engineering, and National 5 * denies any knowledge of its existence. Thus no datasheet is 6 * available off www.national.com. 7 * 8 * (C) Copyright 2000 Linuxcare, Inc. 9 * (C) Copyright 2000 Linuxcare Canada, Inc. 10 * (C) Copyright 2000 Martin K. Petersen <mkp@linuxcare.com> 11 * (C) Copyright 2000 Alex deVries <alex@onefishtwo.ca> 12 * (C) Copyright 2001 John Marvin <jsm fc hp com> 13 * (C) Copyright 2003 Grant Grundler <grundler parisc-linux org> 14 * (C) Copyright 2005 Kyle McMartin <kyle@parisc-linux.org> 15 * (C) Copyright 2006 Helge Deller <deller@gmx.de> 16 * 17 * This program is free software; you can redistribute it and/or 18 * modify it under the terms of the GNU General Public License as 19 * published by the Free Software Foundation; either version 2 of 20 * the License, or (at your option) any later version. 21 * 22 * The initial version of this is by Martin Peterson. Alex deVries 23 * has spent a bit of time trying to coax it into working. 24 * 25 * Major changes to get basic interrupt infrastructure working to 26 * hopefully be able to support all SuperIO devices. Currently 27 * works with serial. -- John Marvin <jsm@fc.hp.com> 28 * 29 * Converted superio_init() to be a PCI_FIXUP_FINAL callee. 30 * -- Kyle McMartin <kyle@parisc-linux.org> 31 */ 32 33 34 /* NOTES: 35 * 36 * Function 0 is an IDE controller. It is identical to a PC87415 IDE 37 * controller (and identifies itself as such). 38 * 39 * Function 1 is a "Legacy I/O" controller. Under this function is a 40 * whole mess of legacy I/O peripherals. Of course, HP hasn't enabled 41 * all the functionality in hardware, but the following is available: 42 * 43 * Two 16550A compatible serial controllers 44 * An IEEE 1284 compatible parallel port 45 * A floppy disk controller 46 * 47 * Function 2 is a USB controller. 48 * 49 * We must be incredibly careful during initialization. Since all 50 * interrupts are routed through function 1 (which is not allowed by 51 * the PCI spec), we need to program the PICs on the legacy I/O port 52 * *before* we attempt to set up IDE and USB. @#$!& 53 * 54 * According to HP, devices are only enabled by firmware if they have 55 * a physical device connected. 56 * 57 * Configuration register bits: 58 * 0x5A: FDC, SP1, IDE1, SP2, IDE2, PAR, Reserved, P92 59 * 0x5B: RTC, 8259, 8254, DMA1, DMA2, KBC, P61, APM 60 * 61 */ 62 63 #include <linux/errno.h> 64 #include <linux/init.h> 65 #include <linux/module.h> 66 #include <linux/types.h> 67 #include <linux/interrupt.h> 68 #include <linux/ioport.h> 69 #include <linux/serial.h> 70 #include <linux/pci.h> 71 #include <linux/parport.h> 72 #include <linux/parport_pc.h> 73 #include <linux/termios.h> 74 #include <linux/tty.h> 75 #include <linux/serial_core.h> 76 #include <linux/serial_8250.h> 77 #include <linux/delay.h> 78 79 #include <asm/io.h> 80 #include <asm/hardware.h> 81 #include <asm/superio.h> 82 83 static struct superio_device sio_dev; 84 85 86 #undef DEBUG_SUPERIO_INIT 87 88 #ifdef DEBUG_SUPERIO_INIT 89 #define DBG_INIT(x...) printk(x) 90 #else 91 #define DBG_INIT(x...) 92 #endif 93 94 #define SUPERIO "SuperIO" 95 #define PFX SUPERIO ": " 96 97 static irqreturn_t 98 superio_interrupt(int parent_irq, void *devp) 99 { 100 u8 results; 101 u8 local_irq; 102 103 /* Poll the 8259 to see if there's an interrupt. */ 104 outb (OCW3_POLL,IC_PIC1+0); 105 106 results = inb(IC_PIC1+0); 107 108 /* 109 * Bit 7: 1 = active Interrupt; 0 = no Interrupt pending 110 * Bits 6-3: zero 111 * Bits 2-0: highest priority, active requesting interrupt ID (0-7) 112 */ 113 if ((results & 0x80) == 0) { 114 /* I suspect "spurious" interrupts are from unmasking an IRQ. 115 * We don't know if an interrupt was/is pending and thus 116 * just call the handler for that IRQ as if it were pending. 117 */ 118 return IRQ_NONE; 119 } 120 121 /* Check to see which device is interrupting */ 122 local_irq = results & 0x0f; 123 124 if (local_irq == 2 || local_irq > 7) { 125 printk(KERN_ERR PFX "slave interrupted!\n"); 126 return IRQ_HANDLED; 127 } 128 129 if (local_irq == 7) { 130 131 /* Could be spurious. Check in service bits */ 132 133 outb(OCW3_ISR,IC_PIC1+0); 134 results = inb(IC_PIC1+0); 135 if ((results & 0x80) == 0) { /* if ISR7 not set: spurious */ 136 printk(KERN_WARNING PFX "spurious interrupt!\n"); 137 return IRQ_HANDLED; 138 } 139 } 140 141 /* Call the appropriate device's interrupt */ 142 generic_handle_irq(local_irq); 143 144 /* set EOI - forces a new interrupt if a lower priority device 145 * still needs service. 146 */ 147 outb((OCW2_SEOI|local_irq),IC_PIC1 + 0); 148 return IRQ_HANDLED; 149 } 150 151 /* Initialize Super I/O device */ 152 static void 153 superio_init(struct pci_dev *pcidev) 154 { 155 struct superio_device *sio = &sio_dev; 156 struct pci_dev *pdev = sio->lio_pdev; 157 u16 word; 158 int ret; 159 160 if (sio->suckyio_irq_enabled) 161 return; 162 163 BUG_ON(!pdev); 164 BUG_ON(!sio->usb_pdev); 165 166 /* use the IRQ iosapic found for USB INT D... */ 167 pdev->irq = sio->usb_pdev->irq; 168 169 /* ...then properly fixup the USB to point at suckyio PIC */ 170 sio->usb_pdev->irq = superio_fixup_irq(sio->usb_pdev); 171 172 printk(KERN_INFO PFX "Found NS87560 Legacy I/O device at %s (IRQ %i)\n", 173 pci_name(pdev), pdev->irq); 174 175 pci_read_config_dword (pdev, SIO_SP1BAR, &sio->sp1_base); 176 sio->sp1_base &= ~1; 177 printk(KERN_INFO PFX "Serial port 1 at 0x%x\n", sio->sp1_base); 178 179 pci_read_config_dword (pdev, SIO_SP2BAR, &sio->sp2_base); 180 sio->sp2_base &= ~1; 181 printk(KERN_INFO PFX "Serial port 2 at 0x%x\n", sio->sp2_base); 182 183 pci_read_config_dword (pdev, SIO_PPBAR, &sio->pp_base); 184 sio->pp_base &= ~1; 185 printk(KERN_INFO PFX "Parallel port at 0x%x\n", sio->pp_base); 186 187 pci_read_config_dword (pdev, SIO_FDCBAR, &sio->fdc_base); 188 sio->fdc_base &= ~1; 189 printk(KERN_INFO PFX "Floppy controller at 0x%x\n", sio->fdc_base); 190 pci_read_config_dword (pdev, SIO_ACPIBAR, &sio->acpi_base); 191 sio->acpi_base &= ~1; 192 printk(KERN_INFO PFX "ACPI at 0x%x\n", sio->acpi_base); 193 194 request_region (IC_PIC1, 0x1f, "pic1"); 195 request_region (IC_PIC2, 0x1f, "pic2"); 196 request_region (sio->acpi_base, 0x1f, "acpi"); 197 198 /* Enable the legacy I/O function */ 199 pci_read_config_word (pdev, PCI_COMMAND, &word); 200 word |= PCI_COMMAND_SERR | PCI_COMMAND_PARITY | PCI_COMMAND_IO; 201 pci_write_config_word (pdev, PCI_COMMAND, word); 202 203 pci_set_master (pdev); 204 ret = pci_enable_device(pdev); 205 BUG_ON(ret < 0); /* not too much we can do about this... */ 206 207 /* 208 * Next project is programming the onboard interrupt controllers. 209 * PDC hasn't done this for us, since it's using polled I/O. 210 * 211 * XXX Use dword writes to avoid bugs in Elroy or Suckyio Config 212 * space access. PCI is by nature a 32-bit bus and config 213 * space can be sensitive to that. 214 */ 215 216 /* 0x64 - 0x67 : 217 DMA Rtg 2 218 DMA Rtg 3 219 DMA Chan Ctl 220 TRIGGER_1 == 0x82 USB & IDE level triggered, rest to edge 221 */ 222 pci_write_config_dword (pdev, 0x64, 0x82000000U); 223 224 /* 0x68 - 0x6b : 225 TRIGGER_2 == 0x00 all edge triggered (not used) 226 CFG_IR_SER == 0x43 SerPort1 = IRQ3, SerPort2 = IRQ4 227 CFG_IR_PF == 0x65 ParPort = IRQ5, FloppyCtlr = IRQ6 228 CFG_IR_IDE == 0x07 IDE1 = IRQ7, reserved 229 */ 230 pci_write_config_dword (pdev, TRIGGER_2, 0x07654300U); 231 232 /* 0x6c - 0x6f : 233 CFG_IR_INTAB == 0x00 234 CFG_IR_INTCD == 0x10 USB = IRQ1 235 CFG_IR_PS2 == 0x00 236 CFG_IR_FXBUS == 0x00 237 */ 238 pci_write_config_dword (pdev, CFG_IR_INTAB, 0x00001000U); 239 240 /* 0x70 - 0x73 : 241 CFG_IR_USB == 0x00 not used. USB is connected to INTD. 242 CFG_IR_ACPI == 0x00 not used. 243 DMA Priority == 0x4c88 Power on default value. NFC. 244 */ 245 pci_write_config_dword (pdev, CFG_IR_USB, 0x4c880000U); 246 247 /* PIC1 Initialization Command Word register programming */ 248 outb (0x11,IC_PIC1+0); /* ICW1: ICW4 write req | ICW1 */ 249 outb (0x00,IC_PIC1+1); /* ICW2: interrupt vector table - not used */ 250 outb (0x04,IC_PIC1+1); /* ICW3: Cascade */ 251 outb (0x01,IC_PIC1+1); /* ICW4: x86 mode */ 252 253 /* PIC1 Program Operational Control Words */ 254 outb (0xff,IC_PIC1+1); /* OCW1: Mask all interrupts */ 255 outb (0xc2,IC_PIC1+0); /* OCW2: priority (3-7,0-2) */ 256 257 /* PIC2 Initialization Command Word register programming */ 258 outb (0x11,IC_PIC2+0); /* ICW1: ICW4 write req | ICW1 */ 259 outb (0x00,IC_PIC2+1); /* ICW2: N/A */ 260 outb (0x02,IC_PIC2+1); /* ICW3: Slave ID code */ 261 outb (0x01,IC_PIC2+1); /* ICW4: x86 mode */ 262 263 /* Program Operational Control Words */ 264 outb (0xff,IC_PIC1+1); /* OCW1: Mask all interrupts */ 265 outb (0x68,IC_PIC1+0); /* OCW3: OCW3 select | ESMM | SMM */ 266 267 /* Write master mask reg */ 268 outb (0xff,IC_PIC1+1); 269 270 /* Setup USB power regulation */ 271 outb(1, sio->acpi_base + USB_REG_CR); 272 if (inb(sio->acpi_base + USB_REG_CR) & 1) 273 printk(KERN_INFO PFX "USB regulator enabled\n"); 274 else 275 printk(KERN_ERR PFX "USB regulator not initialized!\n"); 276 277 if (request_irq(pdev->irq, superio_interrupt, 0, 278 SUPERIO, (void *)sio)) { 279 280 printk(KERN_ERR PFX "could not get irq\n"); 281 BUG(); 282 return; 283 } 284 285 sio->suckyio_irq_enabled = 1; 286 } 287 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87560_LIO, superio_init); 288 289 static void superio_mask_irq(struct irq_data *d) 290 { 291 unsigned int irq = d->irq; 292 u8 r8; 293 294 if ((irq < 1) || (irq == 2) || (irq > 7)) { 295 printk(KERN_ERR PFX "Illegal irq number.\n"); 296 BUG(); 297 return; 298 } 299 300 /* Mask interrupt */ 301 302 r8 = inb(IC_PIC1+1); 303 r8 |= (1 << irq); 304 outb (r8,IC_PIC1+1); 305 } 306 307 static void superio_unmask_irq(struct irq_data *d) 308 { 309 unsigned int irq = d->irq; 310 u8 r8; 311 312 if ((irq < 1) || (irq == 2) || (irq > 7)) { 313 printk(KERN_ERR PFX "Illegal irq number (%d).\n", irq); 314 BUG(); 315 return; 316 } 317 318 /* Unmask interrupt */ 319 r8 = inb(IC_PIC1+1); 320 r8 &= ~(1 << irq); 321 outb (r8,IC_PIC1+1); 322 } 323 324 static struct irq_chip superio_interrupt_type = { 325 .name = SUPERIO, 326 .irq_unmask = superio_unmask_irq, 327 .irq_mask = superio_mask_irq, 328 }; 329 330 #ifdef DEBUG_SUPERIO_INIT 331 static unsigned short expected_device[3] = { 332 PCI_DEVICE_ID_NS_87415, 333 PCI_DEVICE_ID_NS_87560_LIO, 334 PCI_DEVICE_ID_NS_87560_USB 335 }; 336 #endif 337 338 int superio_fixup_irq(struct pci_dev *pcidev) 339 { 340 int local_irq, i; 341 342 #ifdef DEBUG_SUPERIO_INIT 343 int fn; 344 fn = PCI_FUNC(pcidev->devfn); 345 346 /* Verify the function number matches the expected device id. */ 347 if (expected_device[fn] != pcidev->device) { 348 BUG(); 349 return -1; 350 } 351 printk(KERN_DEBUG "superio_fixup_irq(%s) ven 0x%x dev 0x%x from %ps\n", 352 pci_name(pcidev), 353 pcidev->vendor, pcidev->device, 354 __builtin_return_address(0)); 355 #endif 356 357 for (i = 0; i < 16; i++) { 358 irq_set_chip_and_handler(i, &superio_interrupt_type, 359 handle_simple_irq); 360 } 361 362 /* 363 * We don't allocate a SuperIO irq for the legacy IO function, 364 * since it is a "bridge". Instead, we will allocate irq's for 365 * each legacy device as they are initialized. 366 */ 367 368 switch(pcidev->device) { 369 case PCI_DEVICE_ID_NS_87415: /* Function 0 */ 370 local_irq = IDE_IRQ; 371 break; 372 case PCI_DEVICE_ID_NS_87560_LIO: /* Function 1 */ 373 sio_dev.lio_pdev = pcidev; /* save for superio_init() */ 374 return -1; 375 case PCI_DEVICE_ID_NS_87560_USB: /* Function 2 */ 376 sio_dev.usb_pdev = pcidev; /* save for superio_init() */ 377 local_irq = USB_IRQ; 378 break; 379 default: 380 local_irq = -1; 381 BUG(); 382 break; 383 } 384 385 return local_irq; 386 } 387 388 static void __init superio_serial_init(void) 389 { 390 #ifdef CONFIG_SERIAL_8250 391 int retval; 392 struct uart_port serial_port; 393 394 memset(&serial_port, 0, sizeof(serial_port)); 395 serial_port.iotype = UPIO_PORT; 396 serial_port.type = PORT_16550A; 397 serial_port.uartclk = 115200*16; 398 serial_port.flags = UPF_FIXED_PORT | UPF_FIXED_TYPE | 399 UPF_BOOT_AUTOCONF; 400 401 /* serial port #1 */ 402 serial_port.iobase = sio_dev.sp1_base; 403 serial_port.irq = SP1_IRQ; 404 serial_port.line = 0; 405 retval = early_serial_setup(&serial_port); 406 if (retval < 0) { 407 printk(KERN_WARNING PFX "Register Serial #0 failed.\n"); 408 return; 409 } 410 411 /* serial port #2 */ 412 serial_port.iobase = sio_dev.sp2_base; 413 serial_port.irq = SP2_IRQ; 414 serial_port.line = 1; 415 retval = early_serial_setup(&serial_port); 416 if (retval < 0) 417 printk(KERN_WARNING PFX "Register Serial #1 failed.\n"); 418 #endif /* CONFIG_SERIAL_8250 */ 419 } 420 421 422 static void __init superio_parport_init(void) 423 { 424 #ifdef CONFIG_PARPORT_PC 425 if (!parport_pc_probe_port(sio_dev.pp_base, 426 0 /*base_hi*/, 427 PAR_IRQ, 428 PARPORT_DMA_NONE /* dma */, 429 NULL /*struct pci_dev* */, 430 0 /* shared irq flags */)) 431 432 printk(KERN_WARNING PFX "Probing parallel port failed.\n"); 433 #endif /* CONFIG_PARPORT_PC */ 434 } 435 436 437 static void superio_fixup_pci(struct pci_dev *pdev) 438 { 439 u8 prog; 440 441 pdev->class |= 0x5; 442 pci_write_config_byte(pdev, PCI_CLASS_PROG, pdev->class); 443 444 pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog); 445 printk("PCI: Enabled native mode for NS87415 (pif=0x%x)\n", prog); 446 } 447 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87415, superio_fixup_pci); 448 449 450 static int __init 451 superio_probe(struct pci_dev *dev, const struct pci_device_id *id) 452 { 453 struct superio_device *sio = &sio_dev; 454 455 /* 456 ** superio_probe(00:0e.0) ven 0x100b dev 0x2 sv 0x0 sd 0x0 class 0x1018a 457 ** superio_probe(00:0e.1) ven 0x100b dev 0xe sv 0x0 sd 0x0 class 0x68000 458 ** superio_probe(00:0e.2) ven 0x100b dev 0x12 sv 0x0 sd 0x0 class 0xc0310 459 */ 460 DBG_INIT("superio_probe(%s) ven 0x%x dev 0x%x sv 0x%x sd 0x%x class 0x%x\n", 461 pci_name(dev), 462 dev->vendor, dev->device, 463 dev->subsystem_vendor, dev->subsystem_device, 464 dev->class); 465 466 BUG_ON(!sio->suckyio_irq_enabled); /* Enabled by PCI_FIXUP_FINAL */ 467 468 if (dev->device == PCI_DEVICE_ID_NS_87560_LIO) { /* Function 1 */ 469 superio_parport_init(); 470 superio_serial_init(); 471 /* REVISIT XXX : superio_fdc_init() ? */ 472 return 0; 473 } else if (dev->device == PCI_DEVICE_ID_NS_87415) { /* Function 0 */ 474 DBG_INIT("superio_probe: ignoring IDE 87415\n"); 475 } else if (dev->device == PCI_DEVICE_ID_NS_87560_USB) { /* Function 2 */ 476 DBG_INIT("superio_probe: ignoring USB OHCI controller\n"); 477 } else { 478 DBG_INIT("superio_probe: WTF? Fire Extinguisher?\n"); 479 } 480 481 /* Let appropriate other driver claim this device. */ 482 return -ENODEV; 483 } 484 485 static const struct pci_device_id superio_tbl[] __initconst = { 486 { PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87560_LIO) }, 487 { PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87560_USB) }, 488 { PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87415) }, 489 { 0, } 490 }; 491 492 static struct pci_driver superio_driver __refdata = { 493 .name = SUPERIO, 494 .id_table = superio_tbl, 495 .probe = superio_probe, 496 }; 497 498 module_pci_driver(superio_driver); 499