1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 ** I/O Sapic Driver - PCI interrupt line support 4 ** 5 ** (c) Copyright 1999 Grant Grundler 6 ** (c) Copyright 1999 Hewlett-Packard Company 7 ** 8 ** 9 ** The I/O sapic driver manages the Interrupt Redirection Table which is 10 ** the control logic to convert PCI line based interrupts into a Message 11 ** Signaled Interrupt (aka Transaction Based Interrupt, TBI). 12 ** 13 ** Acronyms 14 ** -------- 15 ** HPA Hard Physical Address (aka MMIO address) 16 ** IRQ Interrupt ReQuest. Implies Line based interrupt. 17 ** IRT Interrupt Routing Table (provided by PAT firmware) 18 ** IRdT Interrupt Redirection Table. IRQ line to TXN ADDR/DATA 19 ** table which is implemented in I/O SAPIC. 20 ** ISR Interrupt Service Routine. aka Interrupt handler. 21 ** MSI Message Signaled Interrupt. PCI 2.2 functionality. 22 ** aka Transaction Based Interrupt (or TBI). 23 ** PA Precision Architecture. HP's RISC architecture. 24 ** RISC Reduced Instruction Set Computer. 25 ** 26 ** 27 ** What's a Message Signalled Interrupt? 28 ** ------------------------------------- 29 ** MSI is a write transaction which targets a processor and is similar 30 ** to a processor write to memory or MMIO. MSIs can be generated by I/O 31 ** devices as well as processors and require *architecture* to work. 32 ** 33 ** PA only supports MSI. So I/O subsystems must either natively generate 34 ** MSIs (e.g. GSC or HP-PB) or convert line based interrupts into MSIs 35 ** (e.g. PCI and EISA). IA64 supports MSIs via a "local SAPIC" which 36 ** acts on behalf of a processor. 37 ** 38 ** MSI allows any I/O device to interrupt any processor. This makes 39 ** load balancing of the interrupt processing possible on an SMP platform. 40 ** Interrupts are also ordered WRT to DMA data. It's possible on I/O 41 ** coherent systems to completely eliminate PIO reads from the interrupt 42 ** path. The device and driver must be designed and implemented to 43 ** guarantee all DMA has been issued (issues about atomicity here) 44 ** before the MSI is issued. I/O status can then safely be read from 45 ** DMA'd data by the ISR. 46 ** 47 ** 48 ** PA Firmware 49 ** ----------- 50 ** PA-RISC platforms have two fundamentally different types of firmware. 51 ** For PCI devices, "Legacy" PDC initializes the "INTERRUPT_LINE" register 52 ** and BARs similar to a traditional PC BIOS. 53 ** The newer "PAT" firmware supports PDC calls which return tables. 54 ** PAT firmware only initializes the PCI Console and Boot interface. 55 ** With these tables, the OS can program all other PCI devices. 56 ** 57 ** One such PAT PDC call returns the "Interrupt Routing Table" (IRT). 58 ** The IRT maps each PCI slot's INTA-D "output" line to an I/O SAPIC 59 ** input line. If the IRT is not available, this driver assumes 60 ** INTERRUPT_LINE register has been programmed by firmware. The latter 61 ** case also means online addition of PCI cards can NOT be supported 62 ** even if HW support is present. 63 ** 64 ** All platforms with PAT firmware to date (Oct 1999) use one Interrupt 65 ** Routing Table for the entire platform. 66 ** 67 ** Where's the iosapic? 68 ** -------------------- 69 ** I/O sapic is part of the "Core Electronics Complex". And on HP platforms 70 ** it's integrated as part of the PCI bus adapter, "lba". So no bus walk 71 ** will discover I/O Sapic. I/O Sapic driver learns about each device 72 ** when lba driver advertises the presence of the I/O sapic by calling 73 ** iosapic_register(). 74 ** 75 ** 76 ** IRQ handling notes 77 ** ------------------ 78 ** The IO-SAPIC can indicate to the CPU which interrupt was asserted. 79 ** So, unlike the GSC-ASIC and Dino, we allocate one CPU interrupt per 80 ** IO-SAPIC interrupt and call the device driver's handler directly. 81 ** The IO-SAPIC driver hijacks the CPU interrupt handler so it can 82 ** issue the End Of Interrupt command to the IO-SAPIC. 83 ** 84 ** Overview of exported iosapic functions 85 ** -------------------------------------- 86 ** (caveat: code isn't finished yet - this is just the plan) 87 ** 88 ** iosapic_init: 89 ** o initialize globals (lock, etc) 90 ** o try to read IRT. Presence of IRT determines if this is 91 ** a PAT platform or not. 92 ** 93 ** iosapic_register(): 94 ** o create iosapic_info instance data structure 95 ** o allocate vector_info array for this iosapic 96 ** o initialize vector_info - read corresponding IRdT? 97 ** 98 ** iosapic_xlate_pin: (only called by fixup_irq for PAT platform) 99 ** o intr_pin = read cfg (INTERRUPT_PIN); 100 ** o if (device under PCI-PCI bridge) 101 ** translate slot/pin 102 ** 103 ** iosapic_fixup_irq: 104 ** o if PAT platform (IRT present) 105 ** intr_pin = iosapic_xlate_pin(isi,pcidev): 106 ** intr_line = find IRT entry(isi, PCI_SLOT(pcidev), intr_pin) 107 ** save IRT entry into vector_info later 108 ** write cfg INTERRUPT_LINE (with intr_line)? 109 ** else 110 ** intr_line = pcidev->irq 111 ** IRT pointer = NULL 112 ** endif 113 ** o locate vector_info (needs: isi, intr_line) 114 ** o allocate processor "irq" and get txn_addr/data 115 ** o request_irq(processor_irq, iosapic_interrupt, vector_info,...) 116 ** 117 ** iosapic_enable_irq: 118 ** o clear any pending IRQ on that line 119 ** o enable IRdT - call enable_irq(vector[line]->processor_irq) 120 ** o write EOI in case line is already asserted. 121 ** 122 ** iosapic_disable_irq: 123 ** o disable IRdT - call disable_irq(vector[line]->processor_irq) 124 */ 125 126 #include <linux/pci.h> 127 128 #include <asm/pdc.h> 129 #include <asm/pdcpat.h> 130 #ifdef CONFIG_SUPERIO 131 #include <asm/superio.h> 132 #endif 133 134 #include <asm/ropes.h> 135 #include "iosapic_private.h" 136 137 #define MODULE_NAME "iosapic" 138 139 /* "local" compile flags */ 140 #undef PCI_BRIDGE_FUNCS 141 #undef DEBUG_IOSAPIC 142 #undef DEBUG_IOSAPIC_IRT 143 144 145 #ifdef DEBUG_IOSAPIC 146 #define DBG(x...) printk(x) 147 #else /* DEBUG_IOSAPIC */ 148 #define DBG(x...) 149 #endif /* DEBUG_IOSAPIC */ 150 151 #ifdef DEBUG_IOSAPIC_IRT 152 #define DBG_IRT(x...) printk(x) 153 #else 154 #define DBG_IRT(x...) 155 #endif 156 157 #ifdef CONFIG_64BIT 158 #define COMPARE_IRTE_ADDR(irte, hpa) ((irte)->dest_iosapic_addr == (hpa)) 159 #else 160 #define COMPARE_IRTE_ADDR(irte, hpa) \ 161 ((irte)->dest_iosapic_addr == ((hpa) | 0xffffffff00000000ULL)) 162 #endif 163 164 #define IOSAPIC_REG_SELECT 0x00 165 #define IOSAPIC_REG_WINDOW 0x10 166 #define IOSAPIC_REG_EOI 0x40 167 168 #define IOSAPIC_REG_VERSION 0x1 169 170 #define IOSAPIC_IRDT_ENTRY(idx) (0x10+(idx)*2) 171 #define IOSAPIC_IRDT_ENTRY_HI(idx) (0x11+(idx)*2) 172 173 static inline unsigned int iosapic_read(void __iomem *iosapic, unsigned int reg) 174 { 175 writel(reg, iosapic + IOSAPIC_REG_SELECT); 176 return readl(iosapic + IOSAPIC_REG_WINDOW); 177 } 178 179 static inline void iosapic_write(void __iomem *iosapic, unsigned int reg, u32 val) 180 { 181 writel(reg, iosapic + IOSAPIC_REG_SELECT); 182 writel(val, iosapic + IOSAPIC_REG_WINDOW); 183 } 184 185 #define IOSAPIC_VERSION_MASK 0x000000ff 186 #define IOSAPIC_VERSION(ver) ((int) (ver & IOSAPIC_VERSION_MASK)) 187 188 #define IOSAPIC_MAX_ENTRY_MASK 0x00ff0000 189 #define IOSAPIC_MAX_ENTRY_SHIFT 0x10 190 #define IOSAPIC_IRDT_MAX_ENTRY(ver) \ 191 (int) (((ver) & IOSAPIC_MAX_ENTRY_MASK) >> IOSAPIC_MAX_ENTRY_SHIFT) 192 193 /* bits in the "low" I/O Sapic IRdT entry */ 194 #define IOSAPIC_IRDT_ENABLE 0x10000 195 #define IOSAPIC_IRDT_PO_LOW 0x02000 196 #define IOSAPIC_IRDT_LEVEL_TRIG 0x08000 197 #define IOSAPIC_IRDT_MODE_LPRI 0x00100 198 199 /* bits in the "high" I/O Sapic IRdT entry */ 200 #define IOSAPIC_IRDT_ID_EID_SHIFT 0x10 201 202 203 static DEFINE_SPINLOCK(iosapic_lock); 204 205 static inline void iosapic_eoi(void __iomem *addr, unsigned int data) 206 { 207 __raw_writel(data, addr); 208 } 209 210 /* 211 ** REVISIT: future platforms may have more than one IRT. 212 ** If so, the following three fields form a structure which 213 ** then be linked into a list. Names are chosen to make searching 214 ** for them easy - not necessarily accurate (eg "cell"). 215 ** 216 ** Alternative: iosapic_info could point to the IRT it's in. 217 ** iosapic_register() could search a list of IRT's. 218 */ 219 static struct irt_entry *irt_cell; 220 static size_t irt_num_entry; 221 222 static struct irt_entry *iosapic_alloc_irt(int num_entries) 223 { 224 unsigned long a; 225 226 /* The IRT needs to be 8-byte aligned for the PDC call. 227 * Normally kmalloc would guarantee larger alignment, but 228 * if CONFIG_DEBUG_SLAB is enabled, then we can get only 229 * 4-byte alignment on 32-bit kernels 230 */ 231 a = (unsigned long)kmalloc(sizeof(struct irt_entry) * num_entries + 8, GFP_KERNEL); 232 a = (a + 7UL) & ~7UL; 233 return (struct irt_entry *)a; 234 } 235 236 /** 237 * iosapic_load_irt - Fill in the interrupt routing table 238 * @cell_num: The cell number of the CPU we're currently executing on 239 * @irt: The address to place the new IRT at 240 * @return The number of entries found 241 * 242 * The "Get PCI INT Routing Table Size" option returns the number of 243 * entries in the PCI interrupt routing table for the cell specified 244 * in the cell_number argument. The cell number must be for a cell 245 * within the caller's protection domain. 246 * 247 * The "Get PCI INT Routing Table" option returns, for the cell 248 * specified in the cell_number argument, the PCI interrupt routing 249 * table in the caller allocated memory pointed to by mem_addr. 250 * We assume the IRT only contains entries for I/O SAPIC and 251 * calculate the size based on the size of I/O sapic entries. 252 * 253 * The PCI interrupt routing table entry format is derived from the 254 * IA64 SAL Specification 2.4. The PCI interrupt routing table defines 255 * the routing of PCI interrupt signals between the PCI device output 256 * "pins" and the IO SAPICs' input "lines" (including core I/O PCI 257 * devices). This table does NOT include information for devices/slots 258 * behind PCI to PCI bridges. See PCI to PCI Bridge Architecture Spec. 259 * for the architected method of routing of IRQ's behind PPB's. 260 */ 261 262 263 static int __init 264 iosapic_load_irt(unsigned long cell_num, struct irt_entry **irt) 265 { 266 long status; /* PDC return value status */ 267 struct irt_entry *table; /* start of interrupt routing tbl */ 268 unsigned long num_entries = 0UL; 269 270 BUG_ON(!irt); 271 272 if (is_pdc_pat()) { 273 /* Use pat pdc routine to get interrupt routing table size */ 274 DBG("calling get_irt_size (cell %ld)\n", cell_num); 275 status = pdc_pat_get_irt_size(&num_entries, cell_num); 276 DBG("get_irt_size: %ld\n", status); 277 278 BUG_ON(status != PDC_OK); 279 BUG_ON(num_entries == 0); 280 281 /* 282 ** allocate memory for interrupt routing table 283 ** This interface isn't really right. We are assuming 284 ** the contents of the table are exclusively 285 ** for I/O sapic devices. 286 */ 287 table = iosapic_alloc_irt(num_entries); 288 if (table == NULL) { 289 printk(KERN_WARNING MODULE_NAME ": read_irt : can " 290 "not alloc mem for IRT\n"); 291 return 0; 292 } 293 294 /* get PCI INT routing table */ 295 status = pdc_pat_get_irt(table, cell_num); 296 DBG("pdc_pat_get_irt: %ld\n", status); 297 WARN_ON(status != PDC_OK); 298 } else { 299 /* 300 ** C3000/J5000 (and similar) platforms with Sprockets PDC 301 ** will return exactly one IRT for all iosapics. 302 ** So if we have one, don't need to get it again. 303 */ 304 if (irt_cell) 305 return 0; 306 307 /* Should be using the Elroy's HPA, but it's ignored anyway */ 308 status = pdc_pci_irt_size(&num_entries, 0); 309 DBG("pdc_pci_irt_size: %ld\n", status); 310 311 if (status != PDC_OK) { 312 /* Not a "legacy" system with I/O SAPIC either */ 313 return 0; 314 } 315 316 BUG_ON(num_entries == 0); 317 318 table = iosapic_alloc_irt(num_entries); 319 if (!table) { 320 printk(KERN_WARNING MODULE_NAME ": read_irt : can " 321 "not alloc mem for IRT\n"); 322 return 0; 323 } 324 325 /* HPA ignored by this call too. */ 326 status = pdc_pci_irt(num_entries, 0, table); 327 BUG_ON(status != PDC_OK); 328 } 329 330 /* return interrupt table address */ 331 *irt = table; 332 333 #ifdef DEBUG_IOSAPIC_IRT 334 { 335 struct irt_entry *p = table; 336 int i; 337 338 printk(MODULE_NAME " Interrupt Routing Table (cell %ld)\n", cell_num); 339 printk(MODULE_NAME " start = 0x%p num_entries %ld entry_size %d\n", 340 table, 341 num_entries, 342 (int) sizeof(struct irt_entry)); 343 344 for (i = 0 ; i < num_entries ; i++, p++) { 345 printk(MODULE_NAME " %02x %02x %02x %02x %02x %02x %02x %02x %08x%08x\n", 346 p->entry_type, p->entry_length, p->interrupt_type, 347 p->polarity_trigger, p->src_bus_irq_devno, p->src_bus_id, 348 p->src_seg_id, p->dest_iosapic_intin, 349 ((u32 *) p)[2], 350 ((u32 *) p)[3] 351 ); 352 } 353 } 354 #endif /* DEBUG_IOSAPIC_IRT */ 355 356 return num_entries; 357 } 358 359 360 361 void __init iosapic_init(void) 362 { 363 unsigned long cell = 0; 364 365 DBG("iosapic_init()\n"); 366 367 #ifdef __LP64__ 368 if (is_pdc_pat()) { 369 int status; 370 struct pdc_pat_cell_num cell_info; 371 372 status = pdc_pat_cell_get_number(&cell_info); 373 if (status == PDC_OK) { 374 cell = cell_info.cell_num; 375 } 376 } 377 #endif 378 379 /* get interrupt routing table for this cell */ 380 irt_num_entry = iosapic_load_irt(cell, &irt_cell); 381 if (irt_num_entry == 0) 382 irt_cell = NULL; /* old PDC w/o iosapic */ 383 } 384 385 386 /* 387 ** Return the IRT entry in case we need to look something else up. 388 */ 389 static struct irt_entry * 390 irt_find_irqline(struct iosapic_info *isi, u8 slot, u8 intr_pin) 391 { 392 struct irt_entry *i = irt_cell; 393 int cnt; /* track how many entries we've looked at */ 394 u8 irq_devno = (slot << IRT_DEV_SHIFT) | (intr_pin-1); 395 396 DBG_IRT("irt_find_irqline() SLOT %d pin %d\n", slot, intr_pin); 397 398 for (cnt=0; cnt < irt_num_entry; cnt++, i++) { 399 400 /* 401 ** Validate: entry_type, entry_length, interrupt_type 402 ** 403 ** Difference between validate vs compare is the former 404 ** should print debug info and is not expected to "fail" 405 ** on current platforms. 406 */ 407 if (i->entry_type != IRT_IOSAPIC_TYPE) { 408 DBG_IRT(KERN_WARNING MODULE_NAME ":find_irqline(0x%p): skipping entry %d type %d\n", i, cnt, i->entry_type); 409 continue; 410 } 411 412 if (i->entry_length != IRT_IOSAPIC_LENGTH) { 413 DBG_IRT(KERN_WARNING MODULE_NAME ":find_irqline(0x%p): skipping entry %d length %d\n", i, cnt, i->entry_length); 414 continue; 415 } 416 417 if (i->interrupt_type != IRT_VECTORED_INTR) { 418 DBG_IRT(KERN_WARNING MODULE_NAME ":find_irqline(0x%p): skipping entry %d interrupt_type %d\n", i, cnt, i->interrupt_type); 419 continue; 420 } 421 422 if (!COMPARE_IRTE_ADDR(i, isi->isi_hpa)) 423 continue; 424 425 if ((i->src_bus_irq_devno & IRT_IRQ_DEVNO_MASK) != irq_devno) 426 continue; 427 428 /* 429 ** Ignore: src_bus_id and rc_seg_id correlate with 430 ** iosapic_info->isi_hpa on HP platforms. 431 ** If needed, pass in "PFA" (aka config space addr) 432 ** instead of slot. 433 */ 434 435 /* Found it! */ 436 return i; 437 } 438 439 printk(KERN_WARNING MODULE_NAME ": 0x%lx : no IRT entry for slot %d, pin %d\n", 440 isi->isi_hpa, slot, intr_pin); 441 return NULL; 442 } 443 444 445 /* 446 ** xlate_pin() supports the skewing of IRQ lines done by subsidiary bridges. 447 ** Legacy PDC already does this translation for us and stores it in INTR_LINE. 448 ** 449 ** PAT PDC needs to basically do what legacy PDC does: 450 ** o read PIN 451 ** o adjust PIN in case device is "behind" a PPB 452 ** (eg 4-port 100BT and SCSI/LAN "Combo Card") 453 ** o convert slot/pin to I/O SAPIC input line. 454 ** 455 ** HP platforms only support: 456 ** o one level of skewing for any number of PPBs 457 ** o only support PCI-PCI Bridges. 458 */ 459 static struct irt_entry * 460 iosapic_xlate_pin(struct iosapic_info *isi, struct pci_dev *pcidev) 461 { 462 u8 intr_pin, intr_slot; 463 464 pci_read_config_byte(pcidev, PCI_INTERRUPT_PIN, &intr_pin); 465 466 DBG_IRT("iosapic_xlate_pin(%s) SLOT %d pin %d\n", 467 pcidev->slot_name, PCI_SLOT(pcidev->devfn), intr_pin); 468 469 if (intr_pin == 0) { 470 /* The device does NOT support/use IRQ lines. */ 471 return NULL; 472 } 473 474 /* Check if pcidev behind a PPB */ 475 if (pcidev->bus->parent) { 476 /* Convert pcidev INTR_PIN into something we 477 ** can lookup in the IRT. 478 */ 479 #ifdef PCI_BRIDGE_FUNCS 480 /* 481 ** Proposal #1: 482 ** 483 ** call implementation specific translation function 484 ** This is architecturally "cleaner". HP-UX doesn't 485 ** support other secondary bus types (eg. E/ISA) directly. 486 ** May be needed for other processor (eg IA64) architectures 487 ** or by some ambitous soul who wants to watch TV. 488 */ 489 if (pci_bridge_funcs->xlate_intr_line) { 490 intr_pin = pci_bridge_funcs->xlate_intr_line(pcidev); 491 } 492 #else /* PCI_BRIDGE_FUNCS */ 493 struct pci_bus *p = pcidev->bus; 494 /* 495 ** Proposal #2: 496 ** The "pin" is skewed ((pin + dev - 1) % 4). 497 ** 498 ** This isn't very clean since I/O SAPIC must assume: 499 ** - all platforms only have PCI busses. 500 ** - only PCI-PCI bridge (eg not PCI-EISA, PCI-PCMCIA) 501 ** - IRQ routing is only skewed once regardless of 502 ** the number of PPB's between iosapic and device. 503 ** (Bit3 expansion chassis follows this rule) 504 ** 505 ** Advantage is it's really easy to implement. 506 */ 507 intr_pin = pci_swizzle_interrupt_pin(pcidev, intr_pin); 508 #endif /* PCI_BRIDGE_FUNCS */ 509 510 /* 511 * Locate the host slot of the PPB. 512 */ 513 while (p->parent->parent) 514 p = p->parent; 515 516 intr_slot = PCI_SLOT(p->self->devfn); 517 } else { 518 intr_slot = PCI_SLOT(pcidev->devfn); 519 } 520 DBG_IRT("iosapic_xlate_pin: bus %d slot %d pin %d\n", 521 pcidev->bus->busn_res.start, intr_slot, intr_pin); 522 523 return irt_find_irqline(isi, intr_slot, intr_pin); 524 } 525 526 static void iosapic_rd_irt_entry(struct vector_info *vi , u32 *dp0, u32 *dp1) 527 { 528 struct iosapic_info *isp = vi->iosapic; 529 u8 idx = vi->irqline; 530 531 *dp0 = iosapic_read(isp->addr, IOSAPIC_IRDT_ENTRY(idx)); 532 *dp1 = iosapic_read(isp->addr, IOSAPIC_IRDT_ENTRY_HI(idx)); 533 } 534 535 536 static void iosapic_wr_irt_entry(struct vector_info *vi, u32 dp0, u32 dp1) 537 { 538 struct iosapic_info *isp = vi->iosapic; 539 540 DBG_IRT("iosapic_wr_irt_entry(): irq %d hpa %lx 0x%x 0x%x\n", 541 vi->irqline, isp->isi_hpa, dp0, dp1); 542 543 iosapic_write(isp->addr, IOSAPIC_IRDT_ENTRY(vi->irqline), dp0); 544 545 /* Read the window register to flush the writes down to HW */ 546 dp0 = readl(isp->addr+IOSAPIC_REG_WINDOW); 547 548 iosapic_write(isp->addr, IOSAPIC_IRDT_ENTRY_HI(vi->irqline), dp1); 549 550 /* Read the window register to flush the writes down to HW */ 551 dp1 = readl(isp->addr+IOSAPIC_REG_WINDOW); 552 } 553 554 /* 555 ** set_irt prepares the data (dp0, dp1) according to the vector_info 556 ** and target cpu (id_eid). dp0/dp1 are then used to program I/O SAPIC 557 ** IRdT for the given "vector" (aka IRQ line). 558 */ 559 static void 560 iosapic_set_irt_data( struct vector_info *vi, u32 *dp0, u32 *dp1) 561 { 562 u32 mode = 0; 563 struct irt_entry *p = vi->irte; 564 565 if ((p->polarity_trigger & IRT_PO_MASK) == IRT_ACTIVE_LO) 566 mode |= IOSAPIC_IRDT_PO_LOW; 567 568 if (((p->polarity_trigger >> IRT_EL_SHIFT) & IRT_EL_MASK) == IRT_LEVEL_TRIG) 569 mode |= IOSAPIC_IRDT_LEVEL_TRIG; 570 571 /* 572 ** IA64 REVISIT 573 ** PA doesn't support EXTINT or LPRIO bits. 574 */ 575 576 *dp0 = mode | (u32) vi->txn_data; 577 578 /* 579 ** Extracting id_eid isn't a real clean way of getting it. 580 ** But the encoding is the same for both PA and IA64 platforms. 581 */ 582 if (is_pdc_pat()) { 583 /* 584 ** PAT PDC just hands it to us "right". 585 ** txn_addr comes from cpu_data[x].txn_addr. 586 */ 587 *dp1 = (u32) (vi->txn_addr); 588 } else { 589 /* 590 ** eg if base_addr == 0xfffa0000), 591 ** we want to get 0xa0ff0000. 592 ** 593 ** eid 0x0ff00000 -> 0x00ff0000 594 ** id 0x000ff000 -> 0xff000000 595 */ 596 *dp1 = (((u32)vi->txn_addr & 0x0ff00000) >> 4) | 597 (((u32)vi->txn_addr & 0x000ff000) << 12); 598 } 599 DBG_IRT("iosapic_set_irt_data(): 0x%x 0x%x\n", *dp0, *dp1); 600 } 601 602 603 static void iosapic_mask_irq(struct irq_data *d) 604 { 605 unsigned long flags; 606 struct vector_info *vi = irq_data_get_irq_chip_data(d); 607 u32 d0, d1; 608 609 spin_lock_irqsave(&iosapic_lock, flags); 610 iosapic_rd_irt_entry(vi, &d0, &d1); 611 d0 |= IOSAPIC_IRDT_ENABLE; 612 iosapic_wr_irt_entry(vi, d0, d1); 613 spin_unlock_irqrestore(&iosapic_lock, flags); 614 } 615 616 static void iosapic_unmask_irq(struct irq_data *d) 617 { 618 struct vector_info *vi = irq_data_get_irq_chip_data(d); 619 u32 d0, d1; 620 621 /* data is initialized by fixup_irq */ 622 WARN_ON(vi->txn_irq == 0); 623 624 iosapic_set_irt_data(vi, &d0, &d1); 625 iosapic_wr_irt_entry(vi, d0, d1); 626 627 #ifdef DEBUG_IOSAPIC_IRT 628 { 629 u32 *t = (u32 *) ((ulong) vi->eoi_addr & ~0xffUL); 630 printk("iosapic_enable_irq(): regs %p", vi->eoi_addr); 631 for ( ; t < vi->eoi_addr; t++) 632 printk(" %x", readl(t)); 633 printk("\n"); 634 } 635 636 printk("iosapic_enable_irq(): sel "); 637 { 638 struct iosapic_info *isp = vi->iosapic; 639 640 for (d0=0x10; d0<0x1e; d0++) { 641 d1 = iosapic_read(isp->addr, d0); 642 printk(" %x", d1); 643 } 644 } 645 printk("\n"); 646 #endif 647 648 /* 649 * Issuing I/O SAPIC an EOI causes an interrupt IFF IRQ line is 650 * asserted. IRQ generally should not be asserted when a driver 651 * enables their IRQ. It can lead to "interesting" race conditions 652 * in the driver initialization sequence. 653 */ 654 DBG(KERN_DEBUG "enable_irq(%d): eoi(%p, 0x%x)\n", d->irq, 655 vi->eoi_addr, vi->eoi_data); 656 iosapic_eoi(vi->eoi_addr, vi->eoi_data); 657 } 658 659 static void iosapic_eoi_irq(struct irq_data *d) 660 { 661 struct vector_info *vi = irq_data_get_irq_chip_data(d); 662 663 iosapic_eoi(vi->eoi_addr, vi->eoi_data); 664 cpu_eoi_irq(d); 665 } 666 667 #ifdef CONFIG_SMP 668 static int iosapic_set_affinity_irq(struct irq_data *d, 669 const struct cpumask *dest, bool force) 670 { 671 struct vector_info *vi = irq_data_get_irq_chip_data(d); 672 u32 d0, d1, dummy_d0; 673 unsigned long flags; 674 int dest_cpu; 675 676 dest_cpu = cpu_check_affinity(d, dest); 677 if (dest_cpu < 0) 678 return -1; 679 680 cpumask_copy(irq_data_get_affinity_mask(d), cpumask_of(dest_cpu)); 681 vi->txn_addr = txn_affinity_addr(d->irq, dest_cpu); 682 683 spin_lock_irqsave(&iosapic_lock, flags); 684 /* d1 contains the destination CPU, so only want to set that 685 * entry */ 686 iosapic_rd_irt_entry(vi, &d0, &d1); 687 iosapic_set_irt_data(vi, &dummy_d0, &d1); 688 iosapic_wr_irt_entry(vi, d0, d1); 689 spin_unlock_irqrestore(&iosapic_lock, flags); 690 691 return 0; 692 } 693 #endif 694 695 static struct irq_chip iosapic_interrupt_type = { 696 .name = "IO-SAPIC-level", 697 .irq_unmask = iosapic_unmask_irq, 698 .irq_mask = iosapic_mask_irq, 699 .irq_ack = cpu_ack_irq, 700 .irq_eoi = iosapic_eoi_irq, 701 #ifdef CONFIG_SMP 702 .irq_set_affinity = iosapic_set_affinity_irq, 703 #endif 704 }; 705 706 int iosapic_fixup_irq(void *isi_obj, struct pci_dev *pcidev) 707 { 708 struct iosapic_info *isi = isi_obj; 709 struct irt_entry *irte = NULL; /* only used if PAT PDC */ 710 struct vector_info *vi; 711 int isi_line; /* line used by device */ 712 713 if (!isi) { 714 printk(KERN_WARNING MODULE_NAME ": hpa not registered for %s\n", 715 pci_name(pcidev)); 716 return -1; 717 } 718 719 #ifdef CONFIG_SUPERIO 720 /* 721 * HACK ALERT! (non-compliant PCI device support) 722 * 723 * All SuckyIO interrupts are routed through the PIC's on function 1. 724 * But SuckyIO OHCI USB controller gets an IRT entry anyway because 725 * it advertises INT D for INT_PIN. Use that IRT entry to get the 726 * SuckyIO interrupt routing for PICs on function 1 (*BLEECCHH*). 727 */ 728 if (is_superio_device(pcidev)) { 729 /* We must call superio_fixup_irq() to register the pdev */ 730 pcidev->irq = superio_fixup_irq(pcidev); 731 732 /* Don't return if need to program the IOSAPIC's IRT... */ 733 if (PCI_FUNC(pcidev->devfn) != SUPERIO_USB_FN) 734 return pcidev->irq; 735 } 736 #endif /* CONFIG_SUPERIO */ 737 738 /* lookup IRT entry for isi/slot/pin set */ 739 irte = iosapic_xlate_pin(isi, pcidev); 740 if (!irte) { 741 printk("iosapic: no IRTE for %s (IRQ not connected?)\n", 742 pci_name(pcidev)); 743 return -1; 744 } 745 DBG_IRT("iosapic_fixup_irq(): irte %p %x %x %x %x %x %x %x %x\n", 746 irte, 747 irte->entry_type, 748 irte->entry_length, 749 irte->polarity_trigger, 750 irte->src_bus_irq_devno, 751 irte->src_bus_id, 752 irte->src_seg_id, 753 irte->dest_iosapic_intin, 754 (u32) irte->dest_iosapic_addr); 755 isi_line = irte->dest_iosapic_intin; 756 757 /* get vector info for this input line */ 758 vi = isi->isi_vector + isi_line; 759 DBG_IRT("iosapic_fixup_irq: line %d vi 0x%p\n", isi_line, vi); 760 761 /* If this IRQ line has already been setup, skip it */ 762 if (vi->irte) 763 goto out; 764 765 vi->irte = irte; 766 767 /* 768 * Allocate processor IRQ 769 * 770 * XXX/FIXME The txn_alloc_irq() code and related code should be 771 * moved to enable_irq(). That way we only allocate processor IRQ 772 * bits for devices that actually have drivers claiming them. 773 * Right now we assign an IRQ to every PCI device present, 774 * regardless of whether it's used or not. 775 */ 776 vi->txn_irq = txn_alloc_irq(8); 777 778 if (vi->txn_irq < 0) 779 panic("I/O sapic: couldn't get TXN IRQ\n"); 780 781 /* enable_irq() will use txn_* to program IRdT */ 782 vi->txn_addr = txn_alloc_addr(vi->txn_irq); 783 vi->txn_data = txn_alloc_data(vi->txn_irq); 784 785 vi->eoi_addr = isi->addr + IOSAPIC_REG_EOI; 786 vi->eoi_data = cpu_to_le32(vi->txn_data); 787 788 cpu_claim_irq(vi->txn_irq, &iosapic_interrupt_type, vi); 789 790 out: 791 pcidev->irq = vi->txn_irq; 792 793 DBG_IRT("iosapic_fixup_irq() %d:%d %x %x line %d irq %d\n", 794 PCI_SLOT(pcidev->devfn), PCI_FUNC(pcidev->devfn), 795 pcidev->vendor, pcidev->device, isi_line, pcidev->irq); 796 797 return pcidev->irq; 798 } 799 800 static struct iosapic_info *iosapic_list; 801 802 #ifdef CONFIG_64BIT 803 int iosapic_serial_irq(struct parisc_device *dev) 804 { 805 struct iosapic_info *isi; 806 struct irt_entry *irte; 807 struct vector_info *vi; 808 int cnt; 809 int intin; 810 811 intin = (dev->mod_info >> 24) & 15; 812 813 /* lookup IRT entry for isi/slot/pin set */ 814 for (cnt = 0; cnt < irt_num_entry; cnt++) { 815 irte = &irt_cell[cnt]; 816 if (COMPARE_IRTE_ADDR(irte, dev->mod0) && 817 irte->dest_iosapic_intin == intin) 818 break; 819 } 820 if (cnt >= irt_num_entry) 821 return 0; /* no irq found, force polling */ 822 823 DBG_IRT("iosapic_serial_irq(): irte %p %x %x %x %x %x %x %x %x\n", 824 irte, 825 irte->entry_type, 826 irte->entry_length, 827 irte->polarity_trigger, 828 irte->src_bus_irq_devno, 829 irte->src_bus_id, 830 irte->src_seg_id, 831 irte->dest_iosapic_intin, 832 (u32) irte->dest_iosapic_addr); 833 834 /* search for iosapic */ 835 for (isi = iosapic_list; isi; isi = isi->isi_next) 836 if (isi->isi_hpa == dev->mod0) 837 break; 838 if (!isi) 839 return 0; /* no iosapic found, force polling */ 840 841 /* get vector info for this input line */ 842 vi = isi->isi_vector + intin; 843 DBG_IRT("iosapic_serial_irq: line %d vi 0x%p\n", iosapic_intin, vi); 844 845 /* If this IRQ line has already been setup, skip it */ 846 if (vi->irte) 847 goto out; 848 849 vi->irte = irte; 850 851 /* 852 * Allocate processor IRQ 853 * 854 * XXX/FIXME The txn_alloc_irq() code and related code should be 855 * moved to enable_irq(). That way we only allocate processor IRQ 856 * bits for devices that actually have drivers claiming them. 857 * Right now we assign an IRQ to every PCI device present, 858 * regardless of whether it's used or not. 859 */ 860 vi->txn_irq = txn_alloc_irq(8); 861 862 if (vi->txn_irq < 0) 863 panic("I/O sapic: couldn't get TXN IRQ\n"); 864 865 /* enable_irq() will use txn_* to program IRdT */ 866 vi->txn_addr = txn_alloc_addr(vi->txn_irq); 867 vi->txn_data = txn_alloc_data(vi->txn_irq); 868 869 vi->eoi_addr = isi->addr + IOSAPIC_REG_EOI; 870 vi->eoi_data = cpu_to_le32(vi->txn_data); 871 872 cpu_claim_irq(vi->txn_irq, &iosapic_interrupt_type, vi); 873 874 out: 875 876 return vi->txn_irq; 877 } 878 #endif 879 880 881 /* 882 ** squirrel away the I/O Sapic Version 883 */ 884 static unsigned int 885 iosapic_rd_version(struct iosapic_info *isi) 886 { 887 return iosapic_read(isi->addr, IOSAPIC_REG_VERSION); 888 } 889 890 891 /* 892 ** iosapic_register() is called by "drivers" with an integrated I/O SAPIC. 893 ** Caller must be certain they have an I/O SAPIC and know its MMIO address. 894 ** 895 ** o allocate iosapic_info and add it to the list 896 ** o read iosapic version and squirrel that away 897 ** o read size of IRdT. 898 ** o allocate and initialize isi_vector[] 899 ** o allocate irq region 900 */ 901 void *iosapic_register(unsigned long hpa) 902 { 903 struct iosapic_info *isi = NULL; 904 struct irt_entry *irte = irt_cell; 905 struct vector_info *vip; 906 int cnt; /* track how many entries we've looked at */ 907 908 /* 909 * Astro based platforms can only support PCI OLARD if they implement 910 * PAT PDC. Legacy PDC omits LBAs with no PCI devices from the IRT. 911 * Search the IRT and ignore iosapic's which aren't in the IRT. 912 */ 913 for (cnt=0; cnt < irt_num_entry; cnt++, irte++) { 914 WARN_ON(IRT_IOSAPIC_TYPE != irte->entry_type); 915 if (COMPARE_IRTE_ADDR(irte, hpa)) 916 break; 917 } 918 919 if (cnt >= irt_num_entry) { 920 DBG("iosapic_register() ignoring 0x%lx (NOT FOUND)\n", hpa); 921 return NULL; 922 } 923 924 isi = kzalloc(sizeof(struct iosapic_info), GFP_KERNEL); 925 if (!isi) { 926 BUG(); 927 return NULL; 928 } 929 930 isi->addr = ioremap(hpa, 4096); 931 isi->isi_hpa = hpa; 932 isi->isi_version = iosapic_rd_version(isi); 933 isi->isi_num_vectors = IOSAPIC_IRDT_MAX_ENTRY(isi->isi_version) + 1; 934 935 vip = isi->isi_vector = kcalloc(isi->isi_num_vectors, 936 sizeof(struct vector_info), GFP_KERNEL); 937 if (vip == NULL) { 938 kfree(isi); 939 return NULL; 940 } 941 942 for (cnt=0; cnt < isi->isi_num_vectors; cnt++, vip++) { 943 vip->irqline = (unsigned char) cnt; 944 vip->iosapic = isi; 945 } 946 isi->isi_next = iosapic_list; 947 iosapic_list = isi; 948 return isi; 949 } 950 951 952 #ifdef DEBUG_IOSAPIC 953 954 static void 955 iosapic_prt_irt(void *irt, long num_entry) 956 { 957 unsigned int i, *irp = (unsigned int *) irt; 958 959 960 printk(KERN_DEBUG MODULE_NAME ": Interrupt Routing Table (%lx entries)\n", num_entry); 961 962 for (i=0; i<num_entry; i++, irp += 4) { 963 printk(KERN_DEBUG "%p : %2d %.8x %.8x %.8x %.8x\n", 964 irp, i, irp[0], irp[1], irp[2], irp[3]); 965 } 966 } 967 968 969 static void 970 iosapic_prt_vi(struct vector_info *vi) 971 { 972 printk(KERN_DEBUG MODULE_NAME ": vector_info[%d] is at %p\n", vi->irqline, vi); 973 printk(KERN_DEBUG "\t\tstatus: %.4x\n", vi->status); 974 printk(KERN_DEBUG "\t\ttxn_irq: %d\n", vi->txn_irq); 975 printk(KERN_DEBUG "\t\ttxn_addr: %lx\n", vi->txn_addr); 976 printk(KERN_DEBUG "\t\ttxn_data: %lx\n", vi->txn_data); 977 printk(KERN_DEBUG "\t\teoi_addr: %p\n", vi->eoi_addr); 978 printk(KERN_DEBUG "\t\teoi_data: %x\n", vi->eoi_data); 979 } 980 981 982 static void 983 iosapic_prt_isi(struct iosapic_info *isi) 984 { 985 printk(KERN_DEBUG MODULE_NAME ": io_sapic_info at %p\n", isi); 986 printk(KERN_DEBUG "\t\tisi_hpa: %lx\n", isi->isi_hpa); 987 printk(KERN_DEBUG "\t\tisi_status: %x\n", isi->isi_status); 988 printk(KERN_DEBUG "\t\tisi_version: %x\n", isi->isi_version); 989 printk(KERN_DEBUG "\t\tisi_vector: %p\n", isi->isi_vector); 990 } 991 #endif /* DEBUG_IOSAPIC */ 992