1 /* 2 ** DINO manager 3 ** 4 ** (c) Copyright 1999 Red Hat Software 5 ** (c) Copyright 1999 SuSE GmbH 6 ** (c) Copyright 1999,2000 Hewlett-Packard Company 7 ** (c) Copyright 2000 Grant Grundler 8 ** (c) Copyright 2006 Helge Deller 9 ** 10 ** This program is free software; you can redistribute it and/or modify 11 ** it under the terms of the GNU General Public License as published by 12 ** the Free Software Foundation; either version 2 of the License, or 13 ** (at your option) any later version. 14 ** 15 ** This module provides access to Dino PCI bus (config/IOport spaces) 16 ** and helps manage Dino IRQ lines. 17 ** 18 ** Dino interrupt handling is a bit complicated. 19 ** Dino always writes to the broadcast EIR via irr0 for now. 20 ** (BIG WARNING: using broadcast EIR is a really bad thing for SMP!) 21 ** Only one processor interrupt is used for the 11 IRQ line 22 ** inputs to dino. 23 ** 24 ** The different between Built-in Dino and Card-Mode 25 ** dino is in chip initialization and pci device initialization. 26 ** 27 ** Linux drivers can only use Card-Mode Dino if pci devices I/O port 28 ** BARs are configured and used by the driver. Programming MMIO address 29 ** requires substantial knowledge of available Host I/O address ranges 30 ** is currently not supported. Port/Config accessor functions are the 31 ** same. "BIOS" differences are handled within the existing routines. 32 */ 33 34 /* Changes : 35 ** 2001-06-14 : Clement Moyroud (moyroudc@esiee.fr) 36 ** - added support for the integrated RS232. 37 */ 38 39 /* 40 ** TODO: create a virtual address for each Dino HPA. 41 ** GSC code might be able to do this since IODC data tells us 42 ** how many pages are used. PCI subsystem could (must?) do this 43 ** for PCI drivers devices which implement/use MMIO registers. 44 */ 45 46 #include <linux/delay.h> 47 #include <linux/types.h> 48 #include <linux/kernel.h> 49 #include <linux/pci.h> 50 #include <linux/init.h> 51 #include <linux/ioport.h> 52 #include <linux/slab.h> 53 #include <linux/interrupt.h> /* for struct irqaction */ 54 #include <linux/spinlock.h> /* for spinlock_t and prototypes */ 55 56 #include <asm/pdc.h> 57 #include <asm/page.h> 58 #include <asm/system.h> 59 #include <asm/io.h> 60 #include <asm/hardware.h> 61 62 #include "gsc.h" 63 64 #undef DINO_DEBUG 65 66 #ifdef DINO_DEBUG 67 #define DBG(x...) printk(x) 68 #else 69 #define DBG(x...) 70 #endif 71 72 /* 73 ** Config accessor functions only pass in the 8-bit bus number 74 ** and not the 8-bit "PCI Segment" number. Each Dino will be 75 ** assigned a PCI bus number based on "when" it's discovered. 76 ** 77 ** The "secondary" bus number is set to this before calling 78 ** pci_scan_bus(). If any PPB's are present, the scan will 79 ** discover them and update the "secondary" and "subordinate" 80 ** fields in Dino's pci_bus structure. 81 ** 82 ** Changes in the configuration *will* result in a different 83 ** bus number for each dino. 84 */ 85 86 #define is_card_dino(id) ((id)->hw_type == HPHW_A_DMA) 87 #define is_cujo(id) ((id)->hversion == 0x682) 88 89 #define DINO_IAR0 0x004 90 #define DINO_IODC_ADDR 0x008 91 #define DINO_IODC_DATA_0 0x008 92 #define DINO_IODC_DATA_1 0x008 93 #define DINO_IRR0 0x00C 94 #define DINO_IAR1 0x010 95 #define DINO_IRR1 0x014 96 #define DINO_IMR 0x018 97 #define DINO_IPR 0x01C 98 #define DINO_TOC_ADDR 0x020 99 #define DINO_ICR 0x024 100 #define DINO_ILR 0x028 101 #define DINO_IO_COMMAND 0x030 102 #define DINO_IO_STATUS 0x034 103 #define DINO_IO_CONTROL 0x038 104 #define DINO_IO_GSC_ERR_RESP 0x040 105 #define DINO_IO_ERR_INFO 0x044 106 #define DINO_IO_PCI_ERR_RESP 0x048 107 #define DINO_IO_FBB_EN 0x05c 108 #define DINO_IO_ADDR_EN 0x060 109 #define DINO_PCI_ADDR 0x064 110 #define DINO_CONFIG_DATA 0x068 111 #define DINO_IO_DATA 0x06c 112 #define DINO_MEM_DATA 0x070 /* Dino 3.x only */ 113 #define DINO_GSC2X_CONFIG 0x7b4 114 #define DINO_GMASK 0x800 115 #define DINO_PAMR 0x804 116 #define DINO_PAPR 0x808 117 #define DINO_DAMODE 0x80c 118 #define DINO_PCICMD 0x810 119 #define DINO_PCISTS 0x814 120 #define DINO_MLTIM 0x81c 121 #define DINO_BRDG_FEAT 0x820 122 #define DINO_PCIROR 0x824 123 #define DINO_PCIWOR 0x828 124 #define DINO_TLTIM 0x830 125 126 #define DINO_IRQS 11 /* bits 0-10 are architected */ 127 #define DINO_IRR_MASK 0x5ff /* only 10 bits are implemented */ 128 #define DINO_LOCAL_IRQS (DINO_IRQS+1) 129 130 #define DINO_MASK_IRQ(x) (1<<(x)) 131 132 #define PCIINTA 0x001 133 #define PCIINTB 0x002 134 #define PCIINTC 0x004 135 #define PCIINTD 0x008 136 #define PCIINTE 0x010 137 #define PCIINTF 0x020 138 #define GSCEXTINT 0x040 139 /* #define xxx 0x080 - bit 7 is "default" */ 140 /* #define xxx 0x100 - bit 8 not used */ 141 /* #define xxx 0x200 - bit 9 not used */ 142 #define RS232INT 0x400 143 144 struct dino_device 145 { 146 struct pci_hba_data hba; /* 'C' inheritance - must be first */ 147 spinlock_t dinosaur_pen; 148 unsigned long txn_addr; /* EIR addr to generate interrupt */ 149 u32 txn_data; /* EIR data assign to each dino */ 150 u32 imr; /* IRQ's which are enabled */ 151 int global_irq[DINO_LOCAL_IRQS]; /* map IMR bit to global irq */ 152 #ifdef DINO_DEBUG 153 unsigned int dino_irr0; /* save most recent IRQ line stat */ 154 #endif 155 }; 156 157 /* Looks nice and keeps the compiler happy */ 158 #define DINO_DEV(d) ((struct dino_device *) d) 159 160 161 /* 162 * Dino Configuration Space Accessor Functions 163 */ 164 165 #define DINO_CFG_TOK(bus,dfn,pos) ((u32) ((bus)<<16 | (dfn)<<8 | (pos))) 166 167 /* 168 * keep the current highest bus count to assist in allocating busses. This 169 * tries to keep a global bus count total so that when we discover an 170 * entirely new bus, it can be given a unique bus number. 171 */ 172 static int dino_current_bus = 0; 173 174 static int dino_cfg_read(struct pci_bus *bus, unsigned int devfn, int where, 175 int size, u32 *val) 176 { 177 struct dino_device *d = DINO_DEV(parisc_walk_tree(bus->bridge)); 178 u32 local_bus = (bus->parent == NULL) ? 0 : bus->secondary; 179 u32 v = DINO_CFG_TOK(local_bus, devfn, where & ~3); 180 void __iomem *base_addr = d->hba.base_addr; 181 unsigned long flags; 182 183 DBG("%s: %p, %d, %d, %d\n", __func__, base_addr, devfn, where, 184 size); 185 spin_lock_irqsave(&d->dinosaur_pen, flags); 186 187 /* tell HW which CFG address */ 188 __raw_writel(v, base_addr + DINO_PCI_ADDR); 189 190 /* generate cfg read cycle */ 191 if (size == 1) { 192 *val = readb(base_addr + DINO_CONFIG_DATA + (where & 3)); 193 } else if (size == 2) { 194 *val = readw(base_addr + DINO_CONFIG_DATA + (where & 2)); 195 } else if (size == 4) { 196 *val = readl(base_addr + DINO_CONFIG_DATA); 197 } 198 199 spin_unlock_irqrestore(&d->dinosaur_pen, flags); 200 return 0; 201 } 202 203 /* 204 * Dino address stepping "feature": 205 * When address stepping, Dino attempts to drive the bus one cycle too soon 206 * even though the type of cycle (config vs. MMIO) might be different. 207 * The read of Ven/Prod ID is harmless and avoids Dino's address stepping. 208 */ 209 static int dino_cfg_write(struct pci_bus *bus, unsigned int devfn, int where, 210 int size, u32 val) 211 { 212 struct dino_device *d = DINO_DEV(parisc_walk_tree(bus->bridge)); 213 u32 local_bus = (bus->parent == NULL) ? 0 : bus->secondary; 214 u32 v = DINO_CFG_TOK(local_bus, devfn, where & ~3); 215 void __iomem *base_addr = d->hba.base_addr; 216 unsigned long flags; 217 218 DBG("%s: %p, %d, %d, %d\n", __func__, base_addr, devfn, where, 219 size); 220 spin_lock_irqsave(&d->dinosaur_pen, flags); 221 222 /* avoid address stepping feature */ 223 __raw_writel(v & 0xffffff00, base_addr + DINO_PCI_ADDR); 224 __raw_readl(base_addr + DINO_CONFIG_DATA); 225 226 /* tell HW which CFG address */ 227 __raw_writel(v, base_addr + DINO_PCI_ADDR); 228 /* generate cfg read cycle */ 229 if (size == 1) { 230 writeb(val, base_addr + DINO_CONFIG_DATA + (where & 3)); 231 } else if (size == 2) { 232 writew(val, base_addr + DINO_CONFIG_DATA + (where & 2)); 233 } else if (size == 4) { 234 writel(val, base_addr + DINO_CONFIG_DATA); 235 } 236 237 spin_unlock_irqrestore(&d->dinosaur_pen, flags); 238 return 0; 239 } 240 241 static struct pci_ops dino_cfg_ops = { 242 .read = dino_cfg_read, 243 .write = dino_cfg_write, 244 }; 245 246 247 /* 248 * Dino "I/O Port" Space Accessor Functions 249 * 250 * Many PCI devices don't require use of I/O port space (eg Tulip, 251 * NCR720) since they export the same registers to both MMIO and 252 * I/O port space. Performance is going to stink if drivers use 253 * I/O port instead of MMIO. 254 */ 255 256 #define DINO_PORT_IN(type, size, mask) \ 257 static u##size dino_in##size (struct pci_hba_data *d, u16 addr) \ 258 { \ 259 u##size v; \ 260 unsigned long flags; \ 261 spin_lock_irqsave(&(DINO_DEV(d)->dinosaur_pen), flags); \ 262 /* tell HW which IO Port address */ \ 263 __raw_writel((u32) addr, d->base_addr + DINO_PCI_ADDR); \ 264 /* generate I/O PORT read cycle */ \ 265 v = read##type(d->base_addr+DINO_IO_DATA+(addr&mask)); \ 266 spin_unlock_irqrestore(&(DINO_DEV(d)->dinosaur_pen), flags); \ 267 return v; \ 268 } 269 270 DINO_PORT_IN(b, 8, 3) 271 DINO_PORT_IN(w, 16, 2) 272 DINO_PORT_IN(l, 32, 0) 273 274 #define DINO_PORT_OUT(type, size, mask) \ 275 static void dino_out##size (struct pci_hba_data *d, u16 addr, u##size val) \ 276 { \ 277 unsigned long flags; \ 278 spin_lock_irqsave(&(DINO_DEV(d)->dinosaur_pen), flags); \ 279 /* tell HW which IO port address */ \ 280 __raw_writel((u32) addr, d->base_addr + DINO_PCI_ADDR); \ 281 /* generate cfg write cycle */ \ 282 write##type(val, d->base_addr+DINO_IO_DATA+(addr&mask)); \ 283 spin_unlock_irqrestore(&(DINO_DEV(d)->dinosaur_pen), flags); \ 284 } 285 286 DINO_PORT_OUT(b, 8, 3) 287 DINO_PORT_OUT(w, 16, 2) 288 DINO_PORT_OUT(l, 32, 0) 289 290 static struct pci_port_ops dino_port_ops = { 291 .inb = dino_in8, 292 .inw = dino_in16, 293 .inl = dino_in32, 294 .outb = dino_out8, 295 .outw = dino_out16, 296 .outl = dino_out32 297 }; 298 299 static void dino_mask_irq(struct irq_data *d) 300 { 301 struct dino_device *dino_dev = irq_data_get_irq_chip_data(d); 302 int local_irq = gsc_find_local_irq(d->irq, dino_dev->global_irq, DINO_LOCAL_IRQS); 303 304 DBG(KERN_WARNING "%s(0x%p, %d)\n", __func__, dino_dev, d->irq); 305 306 /* Clear the matching bit in the IMR register */ 307 dino_dev->imr &= ~(DINO_MASK_IRQ(local_irq)); 308 __raw_writel(dino_dev->imr, dino_dev->hba.base_addr+DINO_IMR); 309 } 310 311 static void dino_unmask_irq(struct irq_data *d) 312 { 313 struct dino_device *dino_dev = irq_data_get_irq_chip_data(d); 314 int local_irq = gsc_find_local_irq(d->irq, dino_dev->global_irq, DINO_LOCAL_IRQS); 315 u32 tmp; 316 317 DBG(KERN_WARNING "%s(0x%p, %d)\n", __func__, dino_dev, d->irq); 318 319 /* 320 ** clear pending IRQ bits 321 ** 322 ** This does NOT change ILR state! 323 ** See comment below for ILR usage. 324 */ 325 __raw_readl(dino_dev->hba.base_addr+DINO_IPR); 326 327 /* set the matching bit in the IMR register */ 328 dino_dev->imr |= DINO_MASK_IRQ(local_irq); /* used in dino_isr() */ 329 __raw_writel( dino_dev->imr, dino_dev->hba.base_addr+DINO_IMR); 330 331 /* Emulate "Level Triggered" Interrupt 332 ** Basically, a driver is blowing it if the IRQ line is asserted 333 ** while the IRQ is disabled. But tulip.c seems to do that.... 334 ** Give 'em a kluge award and a nice round of applause! 335 ** 336 ** The gsc_write will generate an interrupt which invokes dino_isr(). 337 ** dino_isr() will read IPR and find nothing. But then catch this 338 ** when it also checks ILR. 339 */ 340 tmp = __raw_readl(dino_dev->hba.base_addr+DINO_ILR); 341 if (tmp & DINO_MASK_IRQ(local_irq)) { 342 DBG(KERN_WARNING "%s(): IRQ asserted! (ILR 0x%x)\n", 343 __func__, tmp); 344 gsc_writel(dino_dev->txn_data, dino_dev->txn_addr); 345 } 346 } 347 348 static struct irq_chip dino_interrupt_type = { 349 .name = "GSC-PCI", 350 .irq_unmask = dino_unmask_irq, 351 .irq_mask = dino_mask_irq, 352 }; 353 354 355 /* 356 * Handle a Processor interrupt generated by Dino. 357 * 358 * ilr_loop counter is a kluge to prevent a "stuck" IRQ line from 359 * wedging the CPU. Could be removed or made optional at some point. 360 */ 361 static irqreturn_t dino_isr(int irq, void *intr_dev) 362 { 363 struct dino_device *dino_dev = intr_dev; 364 u32 mask; 365 int ilr_loop = 100; 366 367 /* read and acknowledge pending interrupts */ 368 #ifdef DINO_DEBUG 369 dino_dev->dino_irr0 = 370 #endif 371 mask = __raw_readl(dino_dev->hba.base_addr+DINO_IRR0) & DINO_IRR_MASK; 372 373 if (mask == 0) 374 return IRQ_NONE; 375 376 ilr_again: 377 do { 378 int local_irq = __ffs(mask); 379 int irq = dino_dev->global_irq[local_irq]; 380 DBG(KERN_DEBUG "%s(%d, %p) mask 0x%x\n", 381 __func__, irq, intr_dev, mask); 382 generic_handle_irq(irq); 383 mask &= ~(1 << local_irq); 384 } while (mask); 385 386 /* Support for level triggered IRQ lines. 387 ** 388 ** Dropping this support would make this routine *much* faster. 389 ** But since PCI requires level triggered IRQ line to share lines... 390 ** device drivers may assume lines are level triggered (and not 391 ** edge triggered like EISA/ISA can be). 392 */ 393 mask = __raw_readl(dino_dev->hba.base_addr+DINO_ILR) & dino_dev->imr; 394 if (mask) { 395 if (--ilr_loop > 0) 396 goto ilr_again; 397 printk(KERN_ERR "Dino 0x%p: stuck interrupt %d\n", 398 dino_dev->hba.base_addr, mask); 399 return IRQ_NONE; 400 } 401 return IRQ_HANDLED; 402 } 403 404 static void dino_assign_irq(struct dino_device *dino, int local_irq, int *irqp) 405 { 406 int irq = gsc_assign_irq(&dino_interrupt_type, dino); 407 if (irq == NO_IRQ) 408 return; 409 410 *irqp = irq; 411 dino->global_irq[local_irq] = irq; 412 } 413 414 static void dino_choose_irq(struct parisc_device *dev, void *ctrl) 415 { 416 int irq; 417 struct dino_device *dino = ctrl; 418 419 switch (dev->id.sversion) { 420 case 0x00084: irq = 8; break; /* PS/2 */ 421 case 0x0008c: irq = 10; break; /* RS232 */ 422 case 0x00096: irq = 8; break; /* PS/2 */ 423 default: return; /* Unknown */ 424 } 425 426 dino_assign_irq(dino, irq, &dev->irq); 427 } 428 429 430 /* 431 * Cirrus 6832 Cardbus reports wrong irq on RDI Tadpole PARISC Laptop (deller@gmx.de) 432 * (the irqs are off-by-one, not sure yet if this is a cirrus, dino-hardware or dino-driver problem...) 433 */ 434 static void __devinit quirk_cirrus_cardbus(struct pci_dev *dev) 435 { 436 u8 new_irq = dev->irq - 1; 437 printk(KERN_INFO "PCI: Cirrus Cardbus IRQ fixup for %s, from %d to %d\n", 438 pci_name(dev), dev->irq, new_irq); 439 dev->irq = new_irq; 440 } 441 DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_CIRRUS, PCI_DEVICE_ID_CIRRUS_6832, quirk_cirrus_cardbus ); 442 443 444 static void __init 445 dino_bios_init(void) 446 { 447 DBG("dino_bios_init\n"); 448 } 449 450 /* 451 * dino_card_setup - Set up the memory space for a Dino in card mode. 452 * @bus: the bus under this dino 453 * 454 * Claim an 8MB chunk of unused IO space and call the generic PCI routines 455 * to set up the addresses of the devices on this bus. 456 */ 457 #define _8MB 0x00800000UL 458 static void __init 459 dino_card_setup(struct pci_bus *bus, void __iomem *base_addr) 460 { 461 int i; 462 struct dino_device *dino_dev = DINO_DEV(parisc_walk_tree(bus->bridge)); 463 struct resource *res; 464 char name[128]; 465 int size; 466 467 res = &dino_dev->hba.lmmio_space; 468 res->flags = IORESOURCE_MEM; 469 size = scnprintf(name, sizeof(name), "Dino LMMIO (%s)", 470 dev_name(bus->bridge)); 471 res->name = kmalloc(size+1, GFP_KERNEL); 472 if(res->name) 473 strcpy((char *)res->name, name); 474 else 475 res->name = dino_dev->hba.lmmio_space.name; 476 477 478 if (ccio_allocate_resource(dino_dev->hba.dev, res, _8MB, 479 F_EXTEND(0xf0000000UL) | _8MB, 480 F_EXTEND(0xffffffffUL) &~ _8MB, _8MB) < 0) { 481 struct list_head *ln, *tmp_ln; 482 483 printk(KERN_ERR "Dino: cannot attach bus %s\n", 484 dev_name(bus->bridge)); 485 /* kill the bus, we can't do anything with it */ 486 list_for_each_safe(ln, tmp_ln, &bus->devices) { 487 struct pci_dev *dev = pci_dev_b(ln); 488 489 list_del(&dev->bus_list); 490 } 491 492 return; 493 } 494 bus->resource[1] = res; 495 bus->resource[0] = &(dino_dev->hba.io_space); 496 497 /* Now tell dino what range it has */ 498 for (i = 1; i < 31; i++) { 499 if (res->start == F_EXTEND(0xf0000000UL | (i * _8MB))) 500 break; 501 } 502 DBG("DINO GSC WRITE i=%d, start=%lx, dino addr = %p\n", 503 i, res->start, base_addr + DINO_IO_ADDR_EN); 504 __raw_writel(1 << i, base_addr + DINO_IO_ADDR_EN); 505 } 506 507 static void __init 508 dino_card_fixup(struct pci_dev *dev) 509 { 510 u32 irq_pin; 511 512 /* 513 ** REVISIT: card-mode PCI-PCI expansion chassis do exist. 514 ** Not sure they were ever productized. 515 ** Die here since we'll die later in dino_inb() anyway. 516 */ 517 if ((dev->class >> 8) == PCI_CLASS_BRIDGE_PCI) { 518 panic("Card-Mode Dino: PCI-PCI Bridge not supported\n"); 519 } 520 521 /* 522 ** Set Latency Timer to 0xff (not a shared bus) 523 ** Set CACHELINE_SIZE. 524 */ 525 dino_cfg_write(dev->bus, dev->devfn, 526 PCI_CACHE_LINE_SIZE, 2, 0xff00 | L1_CACHE_BYTES/4); 527 528 /* 529 ** Program INT_LINE for card-mode devices. 530 ** The cards are hardwired according to this algorithm. 531 ** And it doesn't matter if PPB's are present or not since 532 ** the IRQ lines bypass the PPB. 533 ** 534 ** "-1" converts INTA-D (1-4) to PCIINTA-D (0-3) range. 535 ** The additional "-1" adjusts for skewing the IRQ<->slot. 536 */ 537 dino_cfg_read(dev->bus, dev->devfn, PCI_INTERRUPT_PIN, 1, &irq_pin); 538 dev->irq = pci_swizzle_interrupt_pin(dev, irq_pin) - 1; 539 540 /* Shouldn't really need to do this but it's in case someone tries 541 ** to bypass PCI services and look at the card themselves. 542 */ 543 dino_cfg_write(dev->bus, dev->devfn, PCI_INTERRUPT_LINE, 1, dev->irq); 544 } 545 546 /* The alignment contraints for PCI bridges under dino */ 547 #define DINO_BRIDGE_ALIGN 0x100000 548 549 550 static void __init 551 dino_fixup_bus(struct pci_bus *bus) 552 { 553 struct list_head *ln; 554 struct pci_dev *dev; 555 struct dino_device *dino_dev = DINO_DEV(parisc_walk_tree(bus->bridge)); 556 int port_base = HBA_PORT_BASE(dino_dev->hba.hba_num); 557 558 DBG(KERN_WARNING "%s(0x%p) bus %d platform_data 0x%p\n", 559 __func__, bus, bus->secondary, 560 bus->bridge->platform_data); 561 562 /* Firmware doesn't set up card-mode dino, so we have to */ 563 if (is_card_dino(&dino_dev->hba.dev->id)) { 564 dino_card_setup(bus, dino_dev->hba.base_addr); 565 } else if (bus->parent) { 566 int i; 567 568 pci_read_bridge_bases(bus); 569 570 571 for(i = PCI_BRIDGE_RESOURCES; i < PCI_NUM_RESOURCES; i++) { 572 if((bus->self->resource[i].flags & 573 (IORESOURCE_IO | IORESOURCE_MEM)) == 0) 574 continue; 575 576 if(bus->self->resource[i].flags & IORESOURCE_MEM) { 577 /* There's a quirk to alignment of 578 * bridge memory resources: the start 579 * is the alignment and start-end is 580 * the size. However, firmware will 581 * have assigned start and end, so we 582 * need to take this into account */ 583 bus->self->resource[i].end = bus->self->resource[i].end - bus->self->resource[i].start + DINO_BRIDGE_ALIGN; 584 bus->self->resource[i].start = DINO_BRIDGE_ALIGN; 585 586 } 587 588 DBG("DEBUG %s assigning %d [0x%lx,0x%lx]\n", 589 dev_name(&bus->self->dev), i, 590 bus->self->resource[i].start, 591 bus->self->resource[i].end); 592 WARN_ON(pci_assign_resource(bus->self, i)); 593 DBG("DEBUG %s after assign %d [0x%lx,0x%lx]\n", 594 dev_name(&bus->self->dev), i, 595 bus->self->resource[i].start, 596 bus->self->resource[i].end); 597 } 598 } 599 600 601 list_for_each(ln, &bus->devices) { 602 int i; 603 604 dev = pci_dev_b(ln); 605 if (is_card_dino(&dino_dev->hba.dev->id)) 606 dino_card_fixup(dev); 607 608 /* 609 ** P2PB's only have 2 BARs, no IRQs. 610 ** I'd like to just ignore them for now. 611 */ 612 if ((dev->class >> 8) == PCI_CLASS_BRIDGE_PCI) 613 continue; 614 615 /* Adjust the I/O Port space addresses */ 616 for (i = 0; i < PCI_NUM_RESOURCES; i++) { 617 struct resource *res = &dev->resource[i]; 618 if (res->flags & IORESOURCE_IO) { 619 res->start |= port_base; 620 res->end |= port_base; 621 } 622 #ifdef __LP64__ 623 /* Sign Extend MMIO addresses */ 624 else if (res->flags & IORESOURCE_MEM) { 625 res->start |= F_EXTEND(0UL); 626 res->end |= F_EXTEND(0UL); 627 } 628 #endif 629 } 630 /* null out the ROM resource if there is one (we don't 631 * care about an expansion rom on parisc, since it 632 * usually contains (x86) bios code) */ 633 dev->resource[PCI_ROM_RESOURCE].flags = 0; 634 635 if(dev->irq == 255) { 636 637 #define DINO_FIX_UNASSIGNED_INTERRUPTS 638 #ifdef DINO_FIX_UNASSIGNED_INTERRUPTS 639 640 /* This code tries to assign an unassigned 641 * interrupt. Leave it disabled unless you 642 * *really* know what you're doing since the 643 * pin<->interrupt line mapping varies by bus 644 * and machine */ 645 646 u32 irq_pin; 647 648 dino_cfg_read(dev->bus, dev->devfn, 649 PCI_INTERRUPT_PIN, 1, &irq_pin); 650 irq_pin = pci_swizzle_interrupt_pin(dev, irq_pin) - 1; 651 printk(KERN_WARNING "Device %s has undefined IRQ, " 652 "setting to %d\n", pci_name(dev), irq_pin); 653 dino_cfg_write(dev->bus, dev->devfn, 654 PCI_INTERRUPT_LINE, 1, irq_pin); 655 dino_assign_irq(dino_dev, irq_pin, &dev->irq); 656 #else 657 dev->irq = 65535; 658 printk(KERN_WARNING "Device %s has unassigned IRQ\n", pci_name(dev)); 659 #endif 660 } else { 661 /* Adjust INT_LINE for that busses region */ 662 dino_assign_irq(dino_dev, dev->irq, &dev->irq); 663 } 664 } 665 } 666 667 668 static struct pci_bios_ops dino_bios_ops = { 669 .init = dino_bios_init, 670 .fixup_bus = dino_fixup_bus 671 }; 672 673 674 /* 675 * Initialise a DINO controller chip 676 */ 677 static void __init 678 dino_card_init(struct dino_device *dino_dev) 679 { 680 u32 brdg_feat = 0x00784e05; 681 unsigned long status; 682 683 status = __raw_readl(dino_dev->hba.base_addr+DINO_IO_STATUS); 684 if (status & 0x0000ff80) { 685 __raw_writel(0x00000005, 686 dino_dev->hba.base_addr+DINO_IO_COMMAND); 687 udelay(1); 688 } 689 690 __raw_writel(0x00000000, dino_dev->hba.base_addr+DINO_GMASK); 691 __raw_writel(0x00000001, dino_dev->hba.base_addr+DINO_IO_FBB_EN); 692 __raw_writel(0x00000000, dino_dev->hba.base_addr+DINO_ICR); 693 694 #if 1 695 /* REVISIT - should be a runtime check (eg if (CPU_IS_PCX_L) ...) */ 696 /* 697 ** PCX-L processors don't support XQL like Dino wants it. 698 ** PCX-L2 ignore XQL signal and it doesn't matter. 699 */ 700 brdg_feat &= ~0x4; /* UXQL */ 701 #endif 702 __raw_writel( brdg_feat, dino_dev->hba.base_addr+DINO_BRDG_FEAT); 703 704 /* 705 ** Don't enable address decoding until we know which I/O range 706 ** currently is available from the host. Only affects MMIO 707 ** and not I/O port space. 708 */ 709 __raw_writel(0x00000000, dino_dev->hba.base_addr+DINO_IO_ADDR_EN); 710 711 __raw_writel(0x00000000, dino_dev->hba.base_addr+DINO_DAMODE); 712 __raw_writel(0x00222222, dino_dev->hba.base_addr+DINO_PCIROR); 713 __raw_writel(0x00222222, dino_dev->hba.base_addr+DINO_PCIWOR); 714 715 __raw_writel(0x00000040, dino_dev->hba.base_addr+DINO_MLTIM); 716 __raw_writel(0x00000080, dino_dev->hba.base_addr+DINO_IO_CONTROL); 717 __raw_writel(0x0000008c, dino_dev->hba.base_addr+DINO_TLTIM); 718 719 /* Disable PAMR before writing PAPR */ 720 __raw_writel(0x0000007e, dino_dev->hba.base_addr+DINO_PAMR); 721 __raw_writel(0x0000007f, dino_dev->hba.base_addr+DINO_PAPR); 722 __raw_writel(0x00000000, dino_dev->hba.base_addr+DINO_PAMR); 723 724 /* 725 ** Dino ERS encourages enabling FBB (0x6f). 726 ** We can't until we know *all* devices below us can support it. 727 ** (Something in device configuration header tells us). 728 */ 729 __raw_writel(0x0000004f, dino_dev->hba.base_addr+DINO_PCICMD); 730 731 /* Somewhere, the PCI spec says give devices 1 second 732 ** to recover from the #RESET being de-asserted. 733 ** Experience shows most devices only need 10ms. 734 ** This short-cut speeds up booting significantly. 735 */ 736 mdelay(pci_post_reset_delay); 737 } 738 739 static int __init 740 dino_bridge_init(struct dino_device *dino_dev, const char *name) 741 { 742 unsigned long io_addr; 743 int result, i, count=0; 744 struct resource *res, *prevres = NULL; 745 /* 746 * Decoding IO_ADDR_EN only works for Built-in Dino 747 * since PDC has already initialized this. 748 */ 749 750 io_addr = __raw_readl(dino_dev->hba.base_addr + DINO_IO_ADDR_EN); 751 if (io_addr == 0) { 752 printk(KERN_WARNING "%s: No PCI devices enabled.\n", name); 753 return -ENODEV; 754 } 755 756 res = &dino_dev->hba.lmmio_space; 757 for (i = 0; i < 32; i++) { 758 unsigned long start, end; 759 760 if((io_addr & (1 << i)) == 0) 761 continue; 762 763 start = F_EXTEND(0xf0000000UL) | (i << 23); 764 end = start + 8 * 1024 * 1024 - 1; 765 766 DBG("DINO RANGE %d is at 0x%lx-0x%lx\n", count, 767 start, end); 768 769 if(prevres && prevres->end + 1 == start) { 770 prevres->end = end; 771 } else { 772 if(count >= DINO_MAX_LMMIO_RESOURCES) { 773 printk(KERN_ERR "%s is out of resource windows for range %d (0x%lx-0x%lx)\n", name, count, start, end); 774 break; 775 } 776 prevres = res; 777 res->start = start; 778 res->end = end; 779 res->flags = IORESOURCE_MEM; 780 res->name = kmalloc(64, GFP_KERNEL); 781 if(res->name) 782 snprintf((char *)res->name, 64, "%s LMMIO %d", 783 name, count); 784 res++; 785 count++; 786 } 787 } 788 789 res = &dino_dev->hba.lmmio_space; 790 791 for(i = 0; i < DINO_MAX_LMMIO_RESOURCES; i++) { 792 if(res[i].flags == 0) 793 break; 794 795 result = ccio_request_resource(dino_dev->hba.dev, &res[i]); 796 if (result < 0) { 797 printk(KERN_ERR "%s: failed to claim PCI Bus address " 798 "space %d (0x%lx-0x%lx)!\n", name, i, 799 (unsigned long)res[i].start, (unsigned long)res[i].end); 800 return result; 801 } 802 } 803 return 0; 804 } 805 806 static int __init dino_common_init(struct parisc_device *dev, 807 struct dino_device *dino_dev, const char *name) 808 { 809 int status; 810 u32 eim; 811 struct gsc_irq gsc_irq; 812 struct resource *res; 813 814 pcibios_register_hba(&dino_dev->hba); 815 816 pci_bios = &dino_bios_ops; /* used by pci_scan_bus() */ 817 pci_port = &dino_port_ops; 818 819 /* 820 ** Note: SMP systems can make use of IRR1/IAR1 registers 821 ** But it won't buy much performance except in very 822 ** specific applications/configurations. Note Dino 823 ** still only has 11 IRQ input lines - just map some of them 824 ** to a different processor. 825 */ 826 dev->irq = gsc_alloc_irq(&gsc_irq); 827 dino_dev->txn_addr = gsc_irq.txn_addr; 828 dino_dev->txn_data = gsc_irq.txn_data; 829 eim = ((u32) gsc_irq.txn_addr) | gsc_irq.txn_data; 830 831 /* 832 ** Dino needs a PA "IRQ" to get a processor's attention. 833 ** arch/parisc/kernel/irq.c returns an EIRR bit. 834 */ 835 if (dev->irq < 0) { 836 printk(KERN_WARNING "%s: gsc_alloc_irq() failed\n", name); 837 return 1; 838 } 839 840 status = request_irq(dev->irq, dino_isr, 0, name, dino_dev); 841 if (status) { 842 printk(KERN_WARNING "%s: request_irq() failed with %d\n", 843 name, status); 844 return 1; 845 } 846 847 /* Support the serial port which is sometimes attached on built-in 848 * Dino / Cujo chips. 849 */ 850 851 gsc_fixup_irqs(dev, dino_dev, dino_choose_irq); 852 853 /* 854 ** This enables DINO to generate interrupts when it sees 855 ** any of its inputs *change*. Just asserting an IRQ 856 ** before it's enabled (ie unmasked) isn't good enough. 857 */ 858 __raw_writel(eim, dino_dev->hba.base_addr+DINO_IAR0); 859 860 /* 861 ** Some platforms don't clear Dino's IRR0 register at boot time. 862 ** Reading will clear it now. 863 */ 864 __raw_readl(dino_dev->hba.base_addr+DINO_IRR0); 865 866 /* allocate I/O Port resource region */ 867 res = &dino_dev->hba.io_space; 868 if (!is_cujo(&dev->id)) { 869 res->name = "Dino I/O Port"; 870 } else { 871 res->name = "Cujo I/O Port"; 872 } 873 res->start = HBA_PORT_BASE(dino_dev->hba.hba_num); 874 res->end = res->start + (HBA_PORT_SPACE_SIZE - 1); 875 res->flags = IORESOURCE_IO; /* do not mark it busy ! */ 876 if (request_resource(&ioport_resource, res) < 0) { 877 printk(KERN_ERR "%s: request I/O Port region failed " 878 "0x%lx/%lx (hpa 0x%p)\n", 879 name, (unsigned long)res->start, (unsigned long)res->end, 880 dino_dev->hba.base_addr); 881 return 1; 882 } 883 884 return 0; 885 } 886 887 #define CUJO_RAVEN_ADDR F_EXTEND(0xf1000000UL) 888 #define CUJO_FIREHAWK_ADDR F_EXTEND(0xf1604000UL) 889 #define CUJO_RAVEN_BADPAGE 0x01003000UL 890 #define CUJO_FIREHAWK_BADPAGE 0x01607000UL 891 892 static const char *dino_vers[] = { 893 "2.0", 894 "2.1", 895 "3.0", 896 "3.1" 897 }; 898 899 static const char *cujo_vers[] = { 900 "1.0", 901 "2.0" 902 }; 903 904 void ccio_cujo20_fixup(struct parisc_device *dev, u32 iovp); 905 906 /* 907 ** Determine if dino should claim this chip (return 0) or not (return 1). 908 ** If so, initialize the chip appropriately (card-mode vs bridge mode). 909 ** Much of the initialization is common though. 910 */ 911 static int __init dino_probe(struct parisc_device *dev) 912 { 913 struct dino_device *dino_dev; // Dino specific control struct 914 const char *version = "unknown"; 915 char *name; 916 int is_cujo = 0; 917 LIST_HEAD(resources); 918 struct pci_bus *bus; 919 unsigned long hpa = dev->hpa.start; 920 921 name = "Dino"; 922 if (is_card_dino(&dev->id)) { 923 version = "3.x (card mode)"; 924 } else { 925 if (!is_cujo(&dev->id)) { 926 if (dev->id.hversion_rev < 4) { 927 version = dino_vers[dev->id.hversion_rev]; 928 } 929 } else { 930 name = "Cujo"; 931 is_cujo = 1; 932 if (dev->id.hversion_rev < 2) { 933 version = cujo_vers[dev->id.hversion_rev]; 934 } 935 } 936 } 937 938 printk("%s version %s found at 0x%lx\n", name, version, hpa); 939 940 if (!request_mem_region(hpa, PAGE_SIZE, name)) { 941 printk(KERN_ERR "DINO: Hey! Someone took my MMIO space (0x%ld)!\n", 942 hpa); 943 return 1; 944 } 945 946 /* Check for bugs */ 947 if (is_cujo && dev->id.hversion_rev == 1) { 948 #ifdef CONFIG_IOMMU_CCIO 949 printk(KERN_WARNING "Enabling Cujo 2.0 bug workaround\n"); 950 if (hpa == (unsigned long)CUJO_RAVEN_ADDR) { 951 ccio_cujo20_fixup(dev, CUJO_RAVEN_BADPAGE); 952 } else if (hpa == (unsigned long)CUJO_FIREHAWK_ADDR) { 953 ccio_cujo20_fixup(dev, CUJO_FIREHAWK_BADPAGE); 954 } else { 955 printk("Don't recognise Cujo at address 0x%lx, not enabling workaround\n", hpa); 956 } 957 #endif 958 } else if (!is_cujo && !is_card_dino(&dev->id) && 959 dev->id.hversion_rev < 3) { 960 printk(KERN_WARNING 961 "The GSCtoPCI (Dino hrev %d) bus converter found may exhibit\n" 962 "data corruption. See Service Note Numbers: A4190A-01, A4191A-01.\n" 963 "Systems shipped after Aug 20, 1997 will not exhibit this problem.\n" 964 "Models affected: C180, C160, C160L, B160L, and B132L workstations.\n\n", 965 dev->id.hversion_rev); 966 /* REVISIT: why are C200/C240 listed in the README table but not 967 ** "Models affected"? Could be an omission in the original literature. 968 */ 969 } 970 971 dino_dev = kzalloc(sizeof(struct dino_device), GFP_KERNEL); 972 if (!dino_dev) { 973 printk("dino_init_chip - couldn't alloc dino_device\n"); 974 return 1; 975 } 976 977 dino_dev->hba.dev = dev; 978 dino_dev->hba.base_addr = ioremap_nocache(hpa, 4096); 979 dino_dev->hba.lmmio_space_offset = 0; /* CPU addrs == bus addrs */ 980 spin_lock_init(&dino_dev->dinosaur_pen); 981 dino_dev->hba.iommu = ccio_get_iommu(dev); 982 983 if (is_card_dino(&dev->id)) { 984 dino_card_init(dino_dev); 985 } else { 986 dino_bridge_init(dino_dev, name); 987 } 988 989 if (dino_common_init(dev, dino_dev, name)) 990 return 1; 991 992 dev->dev.platform_data = dino_dev; 993 994 pci_add_resource(&resources, &dino_dev->hba.io_space); 995 if (dino_dev->hba.lmmio_space.flags) 996 pci_add_resource(&resources, &dino_dev->hba.lmmio_space); 997 if (dino_dev->hba.elmmio_space.flags) 998 pci_add_resource(&resources, &dino_dev->hba.elmmio_space); 999 if (dino_dev->hba.gmmio_space.flags) 1000 pci_add_resource(&resources, &dino_dev->hba.gmmio_space); 1001 1002 /* 1003 ** It's not used to avoid chicken/egg problems 1004 ** with configuration accessor functions. 1005 */ 1006 dino_dev->hba.hba_bus = bus = pci_create_root_bus(&dev->dev, 1007 dino_current_bus, &dino_cfg_ops, NULL, &resources); 1008 if (!bus) { 1009 printk(KERN_ERR "ERROR: failed to scan PCI bus on %s (duplicate bus number %d?)\n", 1010 dev_name(&dev->dev), dino_current_bus); 1011 pci_free_resource_list(&resources); 1012 /* increment the bus number in case of duplicates */ 1013 dino_current_bus++; 1014 return 0; 1015 } 1016 1017 bus->subordinate = pci_scan_child_bus(bus); 1018 1019 /* This code *depends* on scanning being single threaded 1020 * if it isn't, this global bus number count will fail 1021 */ 1022 dino_current_bus = bus->subordinate + 1; 1023 pci_bus_assign_resources(bus); 1024 pci_bus_add_devices(bus); 1025 return 0; 1026 } 1027 1028 /* 1029 * Normally, we would just test sversion. But the Elroy PCI adapter has 1030 * the same sversion as Dino, so we have to check hversion as well. 1031 * Unfortunately, the J2240 PDC reports the wrong hversion for the first 1032 * Dino, so we have to test for Dino, Cujo and Dino-in-a-J2240. 1033 * For card-mode Dino, most machines report an sversion of 9D. But 715 1034 * and 725 firmware misreport it as 0x08080 for no adequately explained 1035 * reason. 1036 */ 1037 static struct parisc_device_id dino_tbl[] = { 1038 { HPHW_A_DMA, HVERSION_REV_ANY_ID, 0x004, 0x0009D },/* Card-mode Dino */ 1039 { HPHW_A_DMA, HVERSION_REV_ANY_ID, HVERSION_ANY_ID, 0x08080 }, /* XXX */ 1040 { HPHW_BRIDGE, HVERSION_REV_ANY_ID, 0x680, 0xa }, /* Bridge-mode Dino */ 1041 { HPHW_BRIDGE, HVERSION_REV_ANY_ID, 0x682, 0xa }, /* Bridge-mode Cujo */ 1042 { HPHW_BRIDGE, HVERSION_REV_ANY_ID, 0x05d, 0xa }, /* Dino in a J2240 */ 1043 { 0, } 1044 }; 1045 1046 static struct parisc_driver dino_driver = { 1047 .name = "dino", 1048 .id_table = dino_tbl, 1049 .probe = dino_probe, 1050 }; 1051 1052 /* 1053 * One time initialization to let the world know Dino is here. 1054 * This is the only routine which is NOT static. 1055 * Must be called exactly once before pci_init(). 1056 */ 1057 int __init dino_init(void) 1058 { 1059 register_parisc_driver(&dino_driver); 1060 return 0; 1061 } 1062 1063