1menu "Bus options (PCI, PCMCIA, EISA, GSC, ISA)" 2 3config GSC 4 bool "VSC/GSC/HSC bus support" 5 select HAVE_EISA 6 default y 7 help 8 The VSC, GSC and HSC busses were used from the earliest 700-series 9 workstations up to and including the C360/J2240 workstations. They 10 were also used in servers from the E-class to the K-class. They 11 are not found in B1000, C3000, J5000, A500, L1000, N4000 and upwards. 12 If in doubt, say "Y". 13 14config HPPB 15 bool "HP-PB bus support" 16 depends on GSC 17 help 18 The HP-PB bus was used in the Nova class and K-class servers. 19 If in doubt, say "Y" 20 21config IOMMU_CCIO 22 bool "U2/Uturn I/O MMU" 23 depends on GSC 24 help 25 Say Y here to enable DMA management routines for the first 26 generation of PA-RISC cache-coherent machines. Programs the 27 U2/Uturn chip in "Virtual Mode" and use the I/O MMU. 28 29config GSC_LASI 30 bool "Lasi I/O support" 31 depends on GSC 32 help 33 Say Y here to support the Lasi multifunction chip found in 34 many PA-RISC workstations & servers. It includes interfaces 35 for a parallel port, serial port, NCR 53c710 SCSI, Apricot 36 Ethernet, Harmony audio, PS/2 keyboard & mouse, ISDN, telephony 37 and floppy. Note that you must still enable all the individual 38 drivers for these chips. 39 40config GSC_WAX 41 bool "Wax I/O support" 42 depends on GSC 43 help 44 Say Y here to support the Wax multifunction chip found in some 45 older systems, including B/C/D/R class and 715/64, 715/80 and 46 715/100. Wax includes an EISA adapter, a serial port (not always 47 used), a HIL interface chip and is also known to be used as the 48 GSC bridge for an X.25 GSC card. 49 50config ISA 51 bool "ISA support" 52 depends on EISA 53 help 54 If you want to plug an ISA card into your EISA bus, say Y here. 55 Most people should say N. 56 57config GSC_DINO 58 bool "GSCtoPCI/Dino PCI support" 59 depends on PCI && GSC 60 help 61 Say Y here to support the Dino & Cujo GSC to PCI bridges found in 62 machines from the B132 to the C360, the J2240 and the A180. Some 63 GSC/HSC cards (eg gigabit & dual 100 Mbit Ethernet) have a Dino on 64 the card, and you also need to say Y here if you have such a card. 65 Note that Dino also supplies one of the serial ports on certain 66 machines. If in doubt, say Y. 67 68config PCI_LBA 69 bool "LBA/Elroy PCI support" 70 depends on PCI 71 help 72 Say Y here to support the Elroy PCI Lower Bus Adapter. This is 73 present on B, C, J, L and N-class machines with 4-digit model 74 numbers and the A400/A500. 75 76config IOSAPIC 77 bool 78 depends on PCI_LBA 79 default PCI_LBA 80 81config IOMMU_SBA 82 bool 83 depends on PCI_LBA 84 default PCI_LBA 85 86endmenu 87 88menu "PA-RISC specific drivers" 89 90config SUPERIO 91 bool "SuperIO (SuckyIO) support" 92 depends on PCI_LBA 93 default y 94 help 95 Say Y here to support the SuperIO chip found in Bxxxx, C3xxx and 96 J5xxx+ machines. This enables IDE, Floppy, Parallel Port, and 97 Serial port on those machines. 98 99config CHASSIS_LCD_LED 100 bool "Chassis LCD and LED support" 101 default y 102 select VM_EVENT_COUNTERS 103 help 104 Say Y here if you want to enable support for the Heartbeat, 105 Disk/Network activities LEDs on some PA-RISC machines, 106 or support for the LCD that can be found on recent material. 107 108 This has nothing to do with LED State support for A and E class. 109 110 If unsure, say Y. 111 112config PDC_CHASSIS 113 bool "PDC chassis state codes support" 114 default y 115 help 116 Say Y here if you want to enable support for Chassis codes. 117 That includes support for LED State front panel as found on E 118 class, and support for the GSP Virtual Front Panel (LED State and 119 message logging) as found on high end servers such as A, L and 120 N-class. 121 This driver will also display progress messages on LCD display, 122 such as "INI", "RUN" and "FLT", and might thus clobber messages 123 shown by the LED/LCD driver. 124 This driver updates the state panel (LED and/or LCD) upon system 125 state change (eg: boot, shutdown or panic). 126 127 If unsure, say Y. 128 129 130config PDC_CHASSIS_WARN 131 bool "PDC chassis warnings support" 132 depends on PROC_FS 133 default y 134 help 135 Say Y here if you want to enable support for Chassis warnings. 136 This will add a proc entry '/proc/chassis' giving some information 137 about the overall health state of the system. 138 This includes NVRAM battery level, overtemp or failures such as 139 fans or power units. 140 141 If unsure, say Y. 142 143 144config PDC_STABLE 145 tristate "PDC Stable Storage support" 146 depends on SYSFS 147 default y 148 help 149 Say Y here if you want to enable support for accessing Stable Storage 150 variables (PDC non volatile variables such as Primary Boot Path, 151 Console Path, Autoboot, Autosearch, etc) through SysFS. 152 153 If unsure, say Y. 154 155 To compile this driver as a module, choose M here. 156 The module will be called pdc_stable. 157 158endmenu 159