1 /* SPDX-License-Identifier: GPL-2.0-only */ 2 /* 3 * This file is part of wl12xx 4 * 5 * Copyright (C) 1998-2009 Texas Instruments. All rights reserved. 6 * Copyright (C) 2009 Nokia Corporation 7 * 8 * Contact: Luciano Coelho <luciano.coelho@nokia.com> 9 */ 10 11 #ifndef __REG_H__ 12 #define __REG_H__ 13 14 #include <linux/bitops.h> 15 16 #define REGISTERS_BASE 0x00300000 17 #define DRPW_BASE 0x00310000 18 19 #define REGISTERS_DOWN_SIZE 0x00008800 20 #define REGISTERS_WORK_SIZE 0x0000b000 21 22 #define FW_STATUS_ADDR (0x14FC0 + 0xA000) 23 24 /*=============================================== 25 Host Software Reset - 32bit RW 26 ------------------------------------------ 27 [31:1] Reserved 28 0 SOFT_RESET Soft Reset - When this bit is set, 29 it holds the Wlan hardware in a soft reset state. 30 This reset disables all MAC and baseband processor 31 clocks except the CardBus/PCI interface clock. 32 It also initializes all MAC state machines except 33 the host interface. It does not reload the 34 contents of the EEPROM. When this bit is cleared 35 (not self-clearing), the Wlan hardware 36 exits the software reset state. 37 ===============================================*/ 38 #define WL12XX_SLV_SOFT_RESET (REGISTERS_BASE + 0x0000) 39 40 #define WL1271_SLV_REG_DATA (REGISTERS_BASE + 0x0008) 41 #define WL1271_SLV_REG_ADATA (REGISTERS_BASE + 0x000c) 42 #define WL1271_SLV_MEM_DATA (REGISTERS_BASE + 0x0018) 43 44 #define WL12XX_REG_INTERRUPT_TRIG (REGISTERS_BASE + 0x0474) 45 #define WL12XX_REG_INTERRUPT_TRIG_H (REGISTERS_BASE + 0x0478) 46 47 /*============================================= 48 Host Interrupt Mask Register - 32bit (RW) 49 ------------------------------------------ 50 Setting a bit in this register masks the 51 corresponding interrupt to the host. 52 0 - RX0 - Rx first dubble buffer Data Interrupt 53 1 - TXD - Tx Data Interrupt 54 2 - TXXFR - Tx Transfer Interrupt 55 3 - RX1 - Rx second dubble buffer Data Interrupt 56 4 - RXXFR - Rx Transfer Interrupt 57 5 - EVENT_A - Event Mailbox interrupt 58 6 - EVENT_B - Event Mailbox interrupt 59 7 - WNONHST - Wake On Host Interrupt 60 8 - TRACE_A - Debug Trace interrupt 61 9 - TRACE_B - Debug Trace interrupt 62 10 - CDCMP - Command Complete Interrupt 63 11 - 64 12 - 65 13 - 66 14 - ICOMP - Initialization Complete Interrupt 67 16 - SG SE - Soft Gemini - Sense enable interrupt 68 17 - SG SD - Soft Gemini - Sense disable interrupt 69 18 - - 70 19 - - 71 20 - - 72 21- - 73 Default: 0x0001 74 *==============================================*/ 75 #define WL12XX_REG_INTERRUPT_MASK (REGISTERS_BASE + 0x04DC) 76 77 /*============================================= 78 Host Interrupt Mask Set 16bit, (Write only) 79 ------------------------------------------ 80 Setting a bit in this register sets 81 the corresponding bin in ACX_HINT_MASK register 82 without effecting the mask 83 state of other bits (0 = no effect). 84 ==============================================*/ 85 #define ACX_REG_HINT_MASK_SET (REGISTERS_BASE + 0x04E0) 86 87 /*============================================= 88 Host Interrupt Mask Clear 16bit,(Write only) 89 ------------------------------------------ 90 Setting a bit in this register clears 91 the corresponding bin in ACX_HINT_MASK register 92 without effecting the mask 93 state of other bits (0 = no effect). 94 =============================================*/ 95 #define ACX_REG_HINT_MASK_CLR (REGISTERS_BASE + 0x04E4) 96 97 /*============================================= 98 Host Interrupt Status Nondestructive Read 99 16bit,(Read only) 100 ------------------------------------------ 101 The host can read this register to determine 102 which interrupts are active. 103 Reading this register doesn't 104 effect its content. 105 =============================================*/ 106 #define WL12XX_REG_INTERRUPT_NO_CLEAR (REGISTERS_BASE + 0x04E8) 107 108 /*============================================= 109 Host Interrupt Status Clear on Read Register 110 16bit,(Read only) 111 ------------------------------------------ 112 The host can read this register to determine 113 which interrupts are active. 114 Reading this register clears it, 115 thus making all interrupts inactive. 116 ==============================================*/ 117 #define ACX_REG_INTERRUPT_CLEAR (REGISTERS_BASE + 0x04F8) 118 119 /*============================================= 120 Host Interrupt Acknowledge Register 121 16bit,(Write only) 122 ------------------------------------------ 123 The host can set individual bits in this 124 register to clear (acknowledge) the corresp. 125 interrupt status bits in the HINT_STS_CLR and 126 HINT_STS_ND registers, thus making the 127 assotiated interrupt inactive. (0-no effect) 128 ==============================================*/ 129 #define WL12XX_REG_INTERRUPT_ACK (REGISTERS_BASE + 0x04F0) 130 131 #define WL12XX_REG_RX_DRIVER_COUNTER (REGISTERS_BASE + 0x0538) 132 133 /* Device Configuration registers*/ 134 #define SOR_CFG (REGISTERS_BASE + 0x0800) 135 136 /* Embedded ARM CPU Control */ 137 138 /*=============================================== 139 Halt eCPU - 32bit RW 140 ------------------------------------------ 141 0 HALT_ECPU Halt Embedded CPU - This bit is the 142 compliment of bit 1 (MDATA2) in the SOR_CFG register. 143 During a hardware reset, this bit holds 144 the inverse of MDATA2. 145 When downloading firmware from the host, 146 set this bit (pull down MDATA2). 147 The host clears this bit after downloading the firmware into 148 zero-wait-state SSRAM. 149 When loading firmware from Flash, clear this bit (pull up MDATA2) 150 so that the eCPU can run the bootloader code in Flash 151 HALT_ECPU eCPU State 152 -------------------- 153 1 halt eCPU 154 0 enable eCPU 155 ===============================================*/ 156 #define WL12XX_REG_ECPU_CONTROL (REGISTERS_BASE + 0x0804) 157 158 #define WL12XX_HI_CFG (REGISTERS_BASE + 0x0808) 159 160 /*=============================================== 161 EEPROM Burst Read Start - 32bit RW 162 ------------------------------------------ 163 [31:1] Reserved 164 0 ACX_EE_START - EEPROM Burst Read Start 0 165 Setting this bit starts a burst read from 166 the external EEPROM. 167 If this bit is set (after reset) before an EEPROM read/write, 168 the burst read starts at EEPROM address 0. 169 Otherwise, it starts at the address 170 following the address of the previous access. 171 TheWlan hardware hardware clears this bit automatically. 172 173 Default: 0x00000000 174 *================================================*/ 175 #define ACX_REG_EE_START (REGISTERS_BASE + 0x080C) 176 177 #define WL12XX_OCP_POR_CTR (REGISTERS_BASE + 0x09B4) 178 #define WL12XX_OCP_DATA_WRITE (REGISTERS_BASE + 0x09B8) 179 #define WL12XX_OCP_DATA_READ (REGISTERS_BASE + 0x09BC) 180 #define WL12XX_OCP_CMD (REGISTERS_BASE + 0x09C0) 181 182 #define WL12XX_HOST_WR_ACCESS (REGISTERS_BASE + 0x09F8) 183 184 #define WL12XX_CHIP_ID_B (REGISTERS_BASE + 0x5674) 185 186 #define WL12XX_ENABLE (REGISTERS_BASE + 0x5450) 187 188 /* Power Management registers */ 189 #define WL12XX_ELP_CFG_MODE (REGISTERS_BASE + 0x5804) 190 #define WL12XX_ELP_CMD (REGISTERS_BASE + 0x5808) 191 #define WL12XX_PLL_CAL_TIME (REGISTERS_BASE + 0x5810) 192 #define WL12XX_CLK_REQ_TIME (REGISTERS_BASE + 0x5814) 193 #define WL12XX_CLK_BUF_TIME (REGISTERS_BASE + 0x5818) 194 195 #define WL12XX_CFG_PLL_SYNC_CNT (REGISTERS_BASE + 0x5820) 196 197 /* Scratch Pad registers*/ 198 #define WL12XX_SCR_PAD0 (REGISTERS_BASE + 0x5608) 199 #define WL12XX_SCR_PAD1 (REGISTERS_BASE + 0x560C) 200 #define WL12XX_SCR_PAD2 (REGISTERS_BASE + 0x5610) 201 #define WL12XX_SCR_PAD3 (REGISTERS_BASE + 0x5614) 202 #define WL12XX_SCR_PAD4 (REGISTERS_BASE + 0x5618) 203 #define WL12XX_SCR_PAD4_SET (REGISTERS_BASE + 0x561C) 204 #define WL12XX_SCR_PAD4_CLR (REGISTERS_BASE + 0x5620) 205 #define WL12XX_SCR_PAD5 (REGISTERS_BASE + 0x5624) 206 #define WL12XX_SCR_PAD5_SET (REGISTERS_BASE + 0x5628) 207 #define WL12XX_SCR_PAD5_CLR (REGISTERS_BASE + 0x562C) 208 #define WL12XX_SCR_PAD6 (REGISTERS_BASE + 0x5630) 209 #define WL12XX_SCR_PAD7 (REGISTERS_BASE + 0x5634) 210 #define WL12XX_SCR_PAD8 (REGISTERS_BASE + 0x5638) 211 #define WL12XX_SCR_PAD9 (REGISTERS_BASE + 0x563C) 212 213 /* Spare registers*/ 214 #define WL12XX_SPARE_A1 (REGISTERS_BASE + 0x0994) 215 #define WL12XX_SPARE_A2 (REGISTERS_BASE + 0x0998) 216 #define WL12XX_SPARE_A3 (REGISTERS_BASE + 0x099C) 217 #define WL12XX_SPARE_A4 (REGISTERS_BASE + 0x09A0) 218 #define WL12XX_SPARE_A5 (REGISTERS_BASE + 0x09A4) 219 #define WL12XX_SPARE_A6 (REGISTERS_BASE + 0x09A8) 220 #define WL12XX_SPARE_A7 (REGISTERS_BASE + 0x09AC) 221 #define WL12XX_SPARE_A8 (REGISTERS_BASE + 0x09B0) 222 #define WL12XX_SPARE_B1 (REGISTERS_BASE + 0x5420) 223 #define WL12XX_SPARE_B2 (REGISTERS_BASE + 0x5424) 224 #define WL12XX_SPARE_B3 (REGISTERS_BASE + 0x5428) 225 #define WL12XX_SPARE_B4 (REGISTERS_BASE + 0x542C) 226 #define WL12XX_SPARE_B5 (REGISTERS_BASE + 0x5430) 227 #define WL12XX_SPARE_B6 (REGISTERS_BASE + 0x5434) 228 #define WL12XX_SPARE_B7 (REGISTERS_BASE + 0x5438) 229 #define WL12XX_SPARE_B8 (REGISTERS_BASE + 0x543C) 230 231 #define WL12XX_PLL_PARAMETERS (REGISTERS_BASE + 0x6040) 232 #define WL12XX_WU_COUNTER_PAUSE (REGISTERS_BASE + 0x6008) 233 #define WL12XX_WELP_ARM_COMMAND (REGISTERS_BASE + 0x6100) 234 #define WL12XX_DRPW_SCRATCH_START (DRPW_BASE + 0x002C) 235 236 #define WL12XX_CMD_MBOX_ADDRESS 0x407B4 237 238 #define ACX_REG_EEPROM_START_BIT BIT(1) 239 240 /* Command/Information Mailbox Pointers */ 241 242 /*=============================================== 243 Command Mailbox Pointer - 32bit RW 244 ------------------------------------------ 245 This register holds the start address of 246 the command mailbox located in the Wlan hardware memory. 247 The host must read this pointer after a reset to 248 find the location of the command mailbox. 249 The Wlan hardware initializes the command mailbox 250 pointer with the default address of the command mailbox. 251 The command mailbox pointer is not valid until after 252 the host receives the Init Complete interrupt from 253 the Wlan hardware. 254 ===============================================*/ 255 #define WL12XX_REG_COMMAND_MAILBOX_PTR (WL12XX_SCR_PAD0) 256 257 /*=============================================== 258 Information Mailbox Pointer - 32bit RW 259 ------------------------------------------ 260 This register holds the start address of 261 the information mailbox located in the Wlan hardware memory. 262 The host must read this pointer after a reset to find 263 the location of the information mailbox. 264 The Wlan hardware initializes the information mailbox pointer 265 with the default address of the information mailbox. 266 The information mailbox pointer is not valid 267 until after the host receives the Init Complete interrupt from 268 the Wlan hardware. 269 ===============================================*/ 270 #define WL12XX_REG_EVENT_MAILBOX_PTR (WL12XX_SCR_PAD1) 271 272 /*=============================================== 273 EEPROM Read/Write Request 32bit RW 274 ------------------------------------------ 275 1 EE_READ - EEPROM Read Request 1 - Setting this bit 276 loads a single byte of data into the EE_DATA 277 register from the EEPROM location specified in 278 the EE_ADDR register. 279 The Wlan hardware hardware clears this bit automatically. 280 EE_DATA is valid when this bit is cleared. 281 282 0 EE_WRITE - EEPROM Write Request - Setting this bit 283 writes a single byte of data from the EE_DATA register into the 284 EEPROM location specified in the EE_ADDR register. 285 The Wlan hardware hardware clears this bit automatically. 286 *===============================================*/ 287 #define ACX_EE_CTL_REG EE_CTL 288 #define EE_WRITE 0x00000001ul 289 #define EE_READ 0x00000002ul 290 291 /*=============================================== 292 EEPROM Address - 32bit RW 293 ------------------------------------------ 294 This register specifies the address 295 within the EEPROM from/to which to read/write data. 296 ===============================================*/ 297 #define ACX_EE_ADDR_REG EE_ADDR 298 299 /*=============================================== 300 EEPROM Data - 32bit RW 301 ------------------------------------------ 302 This register either holds the read 8 bits of 303 data from the EEPROM or the write data 304 to be written to the EEPROM. 305 ===============================================*/ 306 #define ACX_EE_DATA_REG EE_DATA 307 308 /*=============================================== 309 EEPROM Base Address - 32bit RW 310 ------------------------------------------ 311 This register holds the upper nine bits 312 [23:15] of the 24-bit Wlan hardware memory 313 address for burst reads from EEPROM accesses. 314 The EEPROM provides the lower 15 bits of this address. 315 The MSB of the address from the EEPROM is ignored. 316 ===============================================*/ 317 #define ACX_EE_CFG EE_CFG 318 319 /*=============================================== 320 GPIO Output Values -32bit, RW 321 ------------------------------------------ 322 [31:16] Reserved 323 [15: 0] Specify the output values (at the output driver inputs) for 324 GPIO[15:0], respectively. 325 ===============================================*/ 326 #define ACX_GPIO_OUT_REG GPIO_OUT 327 #define ACX_MAX_GPIO_LINES 15 328 329 /*=============================================== 330 Contention window -32bit, RW 331 ------------------------------------------ 332 [31:26] Reserved 333 [25:16] Max (0x3ff) 334 [15:07] Reserved 335 [06:00] Current contention window value - default is 0x1F 336 ===============================================*/ 337 #define ACX_CONT_WIND_CFG_REG CONT_WIND_CFG 338 #define ACX_CONT_WIND_MIN_MASK 0x0000007f 339 #define ACX_CONT_WIND_MAX 0x03ff0000 340 341 #define REF_FREQ_19_2 0 342 #define REF_FREQ_26_0 1 343 #define REF_FREQ_38_4 2 344 #define REF_FREQ_40_0 3 345 #define REF_FREQ_33_6 4 346 #define REF_FREQ_NUM 5 347 348 #define LUT_PARAM_INTEGER_DIVIDER 0 349 #define LUT_PARAM_FRACTIONAL_DIVIDER 1 350 #define LUT_PARAM_ATTN_BB 2 351 #define LUT_PARAM_ALPHA_BB 3 352 #define LUT_PARAM_STOP_TIME_BB 4 353 #define LUT_PARAM_BB_PLL_LOOP_FILTER 5 354 #define LUT_PARAM_NUM 6 355 356 #define WL12XX_EEPROMLESS_IND (WL12XX_SCR_PAD4) 357 #define USE_EEPROM 0 358 #define NVS_DATA_BUNDARY_ALIGNMENT 4 359 360 /* Firmware image header size */ 361 #define FW_HDR_SIZE 8 362 363 /****************************************************************************** 364 365 CHANNELS, BAND & REG DOMAINS definitions 366 367 ******************************************************************************/ 368 369 #define SHORT_PREAMBLE_BIT BIT(0) /* CCK or Barker depending on the rate */ 370 #define OFDM_RATE_BIT BIT(6) 371 #define PBCC_RATE_BIT BIT(7) 372 373 enum { 374 CCK_LONG = 0, 375 CCK_SHORT = SHORT_PREAMBLE_BIT, 376 PBCC_LONG = PBCC_RATE_BIT, 377 PBCC_SHORT = PBCC_RATE_BIT | SHORT_PREAMBLE_BIT, 378 OFDM = OFDM_RATE_BIT 379 }; 380 381 /****************************************************************************** 382 383 Transmit-Descriptor RATE-SET field definitions... 384 385 Define a new "Rate-Set" for TX path that incorporates the 386 Rate & Modulation info into a single 16-bit field. 387 388 TxdRateSet_t: 389 b15 - Indicates Preamble type (1=SHORT, 0=LONG). 390 Notes: 391 Must be LONG (0) for 1Mbps rate. 392 Does not apply (set to 0) for RevG-OFDM rates. 393 b14 - Indicates PBCC encoding (1=PBCC, 0=not). 394 Notes: 395 Does not apply (set to 0) for rates 1 and 2 Mbps. 396 Does not apply (set to 0) for RevG-OFDM rates. 397 b13 - Unused (set to 0). 398 b12-b0 - Supported Rate indicator bits as defined below. 399 400 ******************************************************************************/ 401 402 #define OCP_CMD_LOOP 32 403 #define OCP_CMD_WRITE 0x1 404 #define OCP_CMD_READ 0x2 405 #define OCP_READY_MASK BIT(18) 406 #define OCP_STATUS_MASK (BIT(16) | BIT(17)) 407 #define OCP_STATUS_NO_RESP 0x00000 408 #define OCP_STATUS_OK 0x10000 409 #define OCP_STATUS_REQ_FAILED 0x20000 410 #define OCP_STATUS_RESP_ERROR 0x30000 411 412 #define OCP_REG_POLARITY 0x0064 413 #define OCP_REG_CLK_TYPE 0x0448 414 #define OCP_REG_CLK_POLARITY 0x0cb2 415 #define OCP_REG_CLK_PULL 0x0cb4 416 417 #define POLARITY_LOW BIT(1) 418 #define NO_PULL (BIT(14) | BIT(15)) 419 420 #define FREF_CLK_TYPE_BITS 0xfffffe7f 421 #define CLK_REQ_PRCM 0x100 422 #define FREF_CLK_POLARITY_BITS 0xfffff8ff 423 #define CLK_REQ_OUTN_SEL 0x700 424 425 #define WU_COUNTER_PAUSE_VAL 0x3FF 426 427 /* PLL configuration algorithm for wl128x */ 428 #define SYS_CLK_CFG_REG 0x2200 429 /* Bit[0] - 0-TCXO, 1-FREF */ 430 #define MCS_PLL_CLK_SEL_FREF BIT(0) 431 /* Bit[3:2] - 01-TCXO, 10-FREF */ 432 #define WL_CLK_REQ_TYPE_FREF BIT(3) 433 #define WL_CLK_REQ_TYPE_PG2 (BIT(3) | BIT(2)) 434 /* Bit[4] - 0-TCXO, 1-FREF */ 435 #define PRCM_CM_EN_MUX_WLAN_FREF BIT(4) 436 437 #define TCXO_ILOAD_INT_REG 0x2264 438 #define TCXO_CLK_DETECT_REG 0x2266 439 440 #define TCXO_DET_FAILED BIT(4) 441 442 #define FREF_ILOAD_INT_REG 0x2084 443 #define FREF_CLK_DETECT_REG 0x2086 444 #define FREF_CLK_DETECT_FAIL BIT(4) 445 446 /* Use this reg for masking during driver access */ 447 #define WL_SPARE_REG 0x2320 448 #define WL_SPARE_VAL BIT(2) 449 /* Bit[6:5:3] - mask wl write SYS_CLK_CFG[8:5:2:4] */ 450 #define WL_SPARE_MASK_8526 (BIT(6) | BIT(5) | BIT(3)) 451 452 #define PLL_LOCK_COUNTERS_REG 0xD8C 453 #define PLL_LOCK_COUNTERS_COEX 0x0F 454 #define PLL_LOCK_COUNTERS_MCS 0xF0 455 #define MCS_PLL_OVERRIDE_REG 0xD90 456 #define MCS_PLL_CONFIG_REG 0xD92 457 #define MCS_SEL_IN_FREQ_MASK 0x0070 458 #define MCS_SEL_IN_FREQ_SHIFT 4 459 #define MCS_PLL_CONFIG_REG_VAL 0x73 460 #define MCS_PLL_ENABLE_HP (BIT(0) | BIT(1)) 461 462 #define MCS_PLL_M_REG 0xD94 463 #define MCS_PLL_N_REG 0xD96 464 #define MCS_PLL_M_REG_VAL 0xC8 465 #define MCS_PLL_N_REG_VAL 0x07 466 467 #define SDIO_IO_DS 0xd14 468 469 /* SDIO/wSPI DS configuration values */ 470 enum { 471 HCI_IO_DS_8MA = 0, 472 HCI_IO_DS_4MA = 1, /* default */ 473 HCI_IO_DS_6MA = 2, 474 HCI_IO_DS_2MA = 3, 475 }; 476 477 /* end PLL configuration algorithm for wl128x */ 478 479 /* 480 * Host Command Interrupt. Setting this bit masks 481 * the interrupt that the host issues to inform 482 * the FW that it has sent a command 483 * to the Wlan hardware Command Mailbox. 484 */ 485 #define WL12XX_INTR_TRIG_CMD BIT(0) 486 487 /* 488 * Host Event Acknowlegde Interrupt. The host 489 * sets this bit to acknowledge that it received 490 * the unsolicited information from the event 491 * mailbox. 492 */ 493 #define WL12XX_INTR_TRIG_EVENT_ACK BIT(1) 494 495 /*=============================================== 496 HI_CFG Interface Configuration Register Values 497 ------------------------------------------ 498 ===============================================*/ 499 #define HI_CFG_UART_ENABLE 0x00000004 500 #define HI_CFG_RST232_ENABLE 0x00000008 501 #define HI_CFG_CLOCK_REQ_SELECT 0x00000010 502 #define HI_CFG_HOST_INT_ENABLE 0x00000020 503 #define HI_CFG_VLYNQ_OUTPUT_ENABLE 0x00000040 504 #define HI_CFG_HOST_INT_ACTIVE_LOW 0x00000080 505 #define HI_CFG_UART_TX_OUT_GPIO_15 0x00000100 506 #define HI_CFG_UART_TX_OUT_GPIO_14 0x00000200 507 #define HI_CFG_UART_TX_OUT_GPIO_7 0x00000400 508 509 #define HI_CFG_DEF_VAL \ 510 (HI_CFG_UART_ENABLE | \ 511 HI_CFG_RST232_ENABLE | \ 512 HI_CFG_CLOCK_REQ_SELECT | \ 513 HI_CFG_HOST_INT_ENABLE) 514 515 #define WL127X_REG_FUSE_DATA_2_1 0x050a 516 #define WL128X_REG_FUSE_DATA_2_1 0x2152 517 #define PG_VER_MASK 0x3c 518 #define PG_VER_OFFSET 2 519 520 #define WL127X_PG_MAJOR_VER_MASK 0x3 521 #define WL127X_PG_MAJOR_VER_OFFSET 0x0 522 #define WL127X_PG_MINOR_VER_MASK 0xc 523 #define WL127X_PG_MINOR_VER_OFFSET 0x2 524 525 #define WL128X_PG_MAJOR_VER_MASK 0xc 526 #define WL128X_PG_MAJOR_VER_OFFSET 0x2 527 #define WL128X_PG_MINOR_VER_MASK 0x3 528 #define WL128X_PG_MINOR_VER_OFFSET 0x0 529 530 #define WL127X_PG_GET_MAJOR(pg_ver) ((pg_ver & WL127X_PG_MAJOR_VER_MASK) >> \ 531 WL127X_PG_MAJOR_VER_OFFSET) 532 #define WL127X_PG_GET_MINOR(pg_ver) ((pg_ver & WL127X_PG_MINOR_VER_MASK) >> \ 533 WL127X_PG_MINOR_VER_OFFSET) 534 #define WL128X_PG_GET_MAJOR(pg_ver) ((pg_ver & WL128X_PG_MAJOR_VER_MASK) >> \ 535 WL128X_PG_MAJOR_VER_OFFSET) 536 #define WL128X_PG_GET_MINOR(pg_ver) ((pg_ver & WL128X_PG_MINOR_VER_MASK) >> \ 537 WL128X_PG_MINOR_VER_OFFSET) 538 539 #define WL12XX_REG_FUSE_BD_ADDR_1 0x00310eb4 540 #define WL12XX_REG_FUSE_BD_ADDR_2 0x00310eb8 541 542 #endif 543