1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * This file is part of wl1251 4 * 5 * Copyright (C) 2008 Nokia Corporation 6 */ 7 8 #include <linux/slab.h> 9 10 #include "reg.h" 11 #include "boot.h" 12 #include "io.h" 13 #include "spi.h" 14 #include "event.h" 15 #include "acx.h" 16 17 void wl1251_boot_target_enable_interrupts(struct wl1251 *wl) 18 { 19 wl1251_reg_write32(wl, ACX_REG_INTERRUPT_MASK, ~(wl->intr_mask)); 20 wl1251_reg_write32(wl, HI_CFG, HI_CFG_DEF_VAL); 21 } 22 23 int wl1251_boot_soft_reset(struct wl1251 *wl) 24 { 25 unsigned long timeout; 26 u32 boot_data; 27 28 /* perform soft reset */ 29 wl1251_reg_write32(wl, ACX_REG_SLV_SOFT_RESET, ACX_SLV_SOFT_RESET_BIT); 30 31 /* SOFT_RESET is self clearing */ 32 timeout = jiffies + usecs_to_jiffies(SOFT_RESET_MAX_TIME); 33 while (1) { 34 boot_data = wl1251_reg_read32(wl, ACX_REG_SLV_SOFT_RESET); 35 wl1251_debug(DEBUG_BOOT, "soft reset bootdata 0x%x", boot_data); 36 if ((boot_data & ACX_SLV_SOFT_RESET_BIT) == 0) 37 break; 38 39 if (time_after(jiffies, timeout)) { 40 /* 1.2 check pWhalBus->uSelfClearTime if the 41 * timeout was reached */ 42 wl1251_error("soft reset timeout"); 43 return -1; 44 } 45 46 udelay(SOFT_RESET_STALL_TIME); 47 } 48 49 /* disable Rx/Tx */ 50 wl1251_reg_write32(wl, ENABLE, 0x0); 51 52 /* disable auto calibration on start*/ 53 wl1251_reg_write32(wl, SPARE_A2, 0xffff); 54 55 return 0; 56 } 57 58 int wl1251_boot_init_seq(struct wl1251 *wl) 59 { 60 u32 scr_pad6, init_data, tmp, elp_cmd, ref_freq; 61 62 /* 63 * col #1: INTEGER_DIVIDER 64 * col #2: FRACTIONAL_DIVIDER 65 * col #3: ATTN_BB 66 * col #4: ALPHA_BB 67 * col #5: STOP_TIME_BB 68 * col #6: BB_PLL_LOOP_FILTER 69 */ 70 static const u32 LUT[REF_FREQ_NUM][LUT_PARAM_NUM] = { 71 72 { 83, 87381, 0xB, 5, 0xF00, 3}, /* REF_FREQ_19_2*/ 73 { 61, 141154, 0xB, 5, 0x1450, 2}, /* REF_FREQ_26_0*/ 74 { 41, 174763, 0xC, 6, 0x2D00, 1}, /* REF_FREQ_38_4*/ 75 { 40, 0, 0xC, 6, 0x2EE0, 1}, /* REF_FREQ_40_0*/ 76 { 47, 162280, 0xC, 6, 0x2760, 1} /* REF_FREQ_33_6 */ 77 }; 78 79 /* read NVS params */ 80 scr_pad6 = wl1251_reg_read32(wl, SCR_PAD6); 81 wl1251_debug(DEBUG_BOOT, "scr_pad6 0x%x", scr_pad6); 82 83 /* read ELP_CMD */ 84 elp_cmd = wl1251_reg_read32(wl, ELP_CMD); 85 wl1251_debug(DEBUG_BOOT, "elp_cmd 0x%x", elp_cmd); 86 87 /* set the BB calibration time to be 300 usec (PLL_CAL_TIME) */ 88 ref_freq = scr_pad6 & 0x000000FF; 89 wl1251_debug(DEBUG_BOOT, "ref_freq 0x%x", ref_freq); 90 91 wl1251_reg_write32(wl, PLL_CAL_TIME, 0x9); 92 93 /* 94 * PG 1.2: set the clock buffer time to be 210 usec (CLK_BUF_TIME) 95 */ 96 wl1251_reg_write32(wl, CLK_BUF_TIME, 0x6); 97 98 /* 99 * set the clock detect feature to work in the restart wu procedure 100 * (ELP_CFG_MODE[14]) and Select the clock source type 101 * (ELP_CFG_MODE[13:12]) 102 */ 103 tmp = ((scr_pad6 & 0x0000FF00) << 4) | 0x00004000; 104 wl1251_reg_write32(wl, ELP_CFG_MODE, tmp); 105 106 /* PG 1.2: enable the BB PLL fix. Enable the PLL_LIMP_CLK_EN_CMD */ 107 elp_cmd |= 0x00000040; 108 wl1251_reg_write32(wl, ELP_CMD, elp_cmd); 109 110 /* PG 1.2: Set the BB PLL stable time to be 1000usec 111 * (PLL_STABLE_TIME) */ 112 wl1251_reg_write32(wl, CFG_PLL_SYNC_CNT, 0x20); 113 114 /* PG 1.2: read clock request time */ 115 init_data = wl1251_reg_read32(wl, CLK_REQ_TIME); 116 117 /* 118 * PG 1.2: set the clock request time to be ref_clk_settling_time - 119 * 1ms = 4ms 120 */ 121 if (init_data > 0x21) 122 tmp = init_data - 0x21; 123 else 124 tmp = 0; 125 wl1251_reg_write32(wl, CLK_REQ_TIME, tmp); 126 127 /* set BB PLL configurations in RF AFE */ 128 wl1251_reg_write32(wl, 0x003058cc, 0x4B5); 129 130 /* set RF_AFE_REG_5 */ 131 wl1251_reg_write32(wl, 0x003058d4, 0x50); 132 133 /* set RF_AFE_CTRL_REG_2 */ 134 wl1251_reg_write32(wl, 0x00305948, 0x11c001); 135 136 /* 137 * change RF PLL and BB PLL divider for VCO clock and adjust VCO 138 * bais current(RF_AFE_REG_13) 139 */ 140 wl1251_reg_write32(wl, 0x003058f4, 0x1e); 141 142 /* set BB PLL configurations */ 143 tmp = LUT[ref_freq][LUT_PARAM_INTEGER_DIVIDER] | 0x00017000; 144 wl1251_reg_write32(wl, 0x00305840, tmp); 145 146 /* set fractional divider according to Appendix C-BB PLL 147 * Calculations 148 */ 149 tmp = LUT[ref_freq][LUT_PARAM_FRACTIONAL_DIVIDER]; 150 wl1251_reg_write32(wl, 0x00305844, tmp); 151 152 /* set the initial data for the sigma delta */ 153 wl1251_reg_write32(wl, 0x00305848, 0x3039); 154 155 /* 156 * set the accumulator attenuation value, calibration loop1 157 * (alpha), calibration loop2 (beta), calibration loop3 (gamma) and 158 * the VCO gain 159 */ 160 tmp = (LUT[ref_freq][LUT_PARAM_ATTN_BB] << 16) | 161 (LUT[ref_freq][LUT_PARAM_ALPHA_BB] << 12) | 0x1; 162 wl1251_reg_write32(wl, 0x00305854, tmp); 163 164 /* 165 * set the calibration stop time after holdoff time expires and set 166 * settling time HOLD_OFF_TIME_BB 167 */ 168 tmp = LUT[ref_freq][LUT_PARAM_STOP_TIME_BB] | 0x000A0000; 169 wl1251_reg_write32(wl, 0x00305858, tmp); 170 171 /* 172 * set BB PLL Loop filter capacitor3- BB_C3[2:0] and set BB PLL 173 * constant leakage current to linearize PFD to 0uA - 174 * BB_ILOOPF[7:3] 175 */ 176 tmp = LUT[ref_freq][LUT_PARAM_BB_PLL_LOOP_FILTER] | 0x00000030; 177 wl1251_reg_write32(wl, 0x003058f8, tmp); 178 179 /* 180 * set regulator output voltage for n divider to 181 * 1.35-BB_REFDIV[1:0], set charge pump current- BB_CPGAIN[4:2], 182 * set BB PLL Loop filter capacitor2- BB_C2[7:5], set gain of BB 183 * PLL auto-call to normal mode- BB_CALGAIN_3DB[8] 184 */ 185 wl1251_reg_write32(wl, 0x003058f0, 0x29); 186 187 /* enable restart wakeup sequence (ELP_CMD[0]) */ 188 wl1251_reg_write32(wl, ELP_CMD, elp_cmd | 0x1); 189 190 /* restart sequence completed */ 191 udelay(2000); 192 193 return 0; 194 } 195 196 static void wl1251_boot_set_ecpu_ctrl(struct wl1251 *wl, u32 flag) 197 { 198 u32 cpu_ctrl; 199 200 /* 10.5.0 run the firmware (I) */ 201 cpu_ctrl = wl1251_reg_read32(wl, ACX_REG_ECPU_CONTROL); 202 203 /* 10.5.1 run the firmware (II) */ 204 cpu_ctrl &= ~flag; 205 wl1251_reg_write32(wl, ACX_REG_ECPU_CONTROL, cpu_ctrl); 206 } 207 208 int wl1251_boot_run_firmware(struct wl1251 *wl) 209 { 210 int loop, ret; 211 u32 chip_id, acx_intr; 212 213 wl1251_boot_set_ecpu_ctrl(wl, ECPU_CONTROL_HALT); 214 215 chip_id = wl1251_reg_read32(wl, CHIP_ID_B); 216 217 wl1251_debug(DEBUG_BOOT, "chip id after firmware boot: 0x%x", chip_id); 218 219 if (chip_id != wl->chip_id) { 220 wl1251_error("chip id doesn't match after firmware boot"); 221 return -EIO; 222 } 223 224 /* wait for init to complete */ 225 loop = 0; 226 while (loop++ < INIT_LOOP) { 227 udelay(INIT_LOOP_DELAY); 228 acx_intr = wl1251_reg_read32(wl, ACX_REG_INTERRUPT_NO_CLEAR); 229 230 if (acx_intr == 0xffffffff) { 231 wl1251_error("error reading hardware complete " 232 "init indication"); 233 return -EIO; 234 } 235 /* check that ACX_INTR_INIT_COMPLETE is enabled */ 236 else if (acx_intr & WL1251_ACX_INTR_INIT_COMPLETE) { 237 wl1251_reg_write32(wl, ACX_REG_INTERRUPT_ACK, 238 WL1251_ACX_INTR_INIT_COMPLETE); 239 break; 240 } 241 } 242 243 if (loop > INIT_LOOP) { 244 wl1251_error("timeout waiting for the hardware to " 245 "complete initialization"); 246 return -EIO; 247 } 248 249 /* get hardware config command mail box */ 250 wl->cmd_box_addr = wl1251_reg_read32(wl, REG_COMMAND_MAILBOX_PTR); 251 252 /* get hardware config event mail box */ 253 wl->event_box_addr = wl1251_reg_read32(wl, REG_EVENT_MAILBOX_PTR); 254 255 /* set the working partition to its "running" mode offset */ 256 wl1251_set_partition(wl, WL1251_PART_WORK_MEM_START, 257 WL1251_PART_WORK_MEM_SIZE, 258 WL1251_PART_WORK_REG_START, 259 WL1251_PART_WORK_REG_SIZE); 260 261 wl1251_debug(DEBUG_MAILBOX, "cmd_box_addr 0x%x event_box_addr 0x%x", 262 wl->cmd_box_addr, wl->event_box_addr); 263 264 wl1251_acx_fw_version(wl, wl->fw_ver, sizeof(wl->fw_ver)); 265 266 /* 267 * in case of full asynchronous mode the firmware event must be 268 * ready to receive event from the command mailbox 269 */ 270 271 /* enable gpio interrupts */ 272 wl1251_enable_interrupts(wl); 273 274 /* Enable target's interrupts */ 275 wl->intr_mask = WL1251_ACX_INTR_RX0_DATA | 276 WL1251_ACX_INTR_RX1_DATA | 277 WL1251_ACX_INTR_TX_RESULT | 278 WL1251_ACX_INTR_EVENT_A | 279 WL1251_ACX_INTR_EVENT_B | 280 WL1251_ACX_INTR_INIT_COMPLETE; 281 wl1251_boot_target_enable_interrupts(wl); 282 283 wl->event_mask = SCAN_COMPLETE_EVENT_ID | BSS_LOSE_EVENT_ID | 284 SYNCHRONIZATION_TIMEOUT_EVENT_ID | 285 ROAMING_TRIGGER_LOW_RSSI_EVENT_ID | 286 ROAMING_TRIGGER_REGAINED_RSSI_EVENT_ID | 287 REGAINED_BSS_EVENT_ID | BT_PTA_SENSE_EVENT_ID | 288 BT_PTA_PREDICTION_EVENT_ID | JOIN_EVENT_COMPLETE_ID | 289 PS_REPORT_EVENT_ID; 290 291 ret = wl1251_event_unmask(wl); 292 if (ret < 0) { 293 wl1251_error("EVENT mask setting failed"); 294 return ret; 295 } 296 297 wl1251_event_mbox_config(wl); 298 299 /* firmware startup completed */ 300 return 0; 301 } 302 303 static int wl1251_boot_upload_firmware(struct wl1251 *wl) 304 { 305 int addr, chunk_num, partition_limit; 306 size_t fw_data_len, len; 307 u8 *p, *buf; 308 309 /* whal_FwCtrl_LoadFwImageSm() */ 310 311 wl1251_debug(DEBUG_BOOT, "chip id before fw upload: 0x%x", 312 wl1251_reg_read32(wl, CHIP_ID_B)); 313 314 /* 10.0 check firmware length and set partition */ 315 fw_data_len = (wl->fw[4] << 24) | (wl->fw[5] << 16) | 316 (wl->fw[6] << 8) | (wl->fw[7]); 317 318 wl1251_debug(DEBUG_BOOT, "fw_data_len %zu chunk_size %d", fw_data_len, 319 CHUNK_SIZE); 320 321 if ((fw_data_len % 4) != 0) { 322 wl1251_error("firmware length not multiple of four"); 323 return -EIO; 324 } 325 326 buf = kmalloc(CHUNK_SIZE, GFP_KERNEL); 327 if (!buf) { 328 wl1251_error("allocation for firmware upload chunk failed"); 329 return -ENOMEM; 330 } 331 332 wl1251_set_partition(wl, WL1251_PART_DOWN_MEM_START, 333 WL1251_PART_DOWN_MEM_SIZE, 334 WL1251_PART_DOWN_REG_START, 335 WL1251_PART_DOWN_REG_SIZE); 336 337 /* 10.1 set partition limit and chunk num */ 338 chunk_num = 0; 339 partition_limit = WL1251_PART_DOWN_MEM_SIZE; 340 341 while (chunk_num < fw_data_len / CHUNK_SIZE) { 342 /* 10.2 update partition, if needed */ 343 addr = WL1251_PART_DOWN_MEM_START + 344 (chunk_num + 2) * CHUNK_SIZE; 345 if (addr > partition_limit) { 346 addr = WL1251_PART_DOWN_MEM_START + 347 chunk_num * CHUNK_SIZE; 348 partition_limit = chunk_num * CHUNK_SIZE + 349 WL1251_PART_DOWN_MEM_SIZE; 350 wl1251_set_partition(wl, 351 addr, 352 WL1251_PART_DOWN_MEM_SIZE, 353 WL1251_PART_DOWN_REG_START, 354 WL1251_PART_DOWN_REG_SIZE); 355 } 356 357 /* 10.3 upload the chunk */ 358 addr = WL1251_PART_DOWN_MEM_START + chunk_num * CHUNK_SIZE; 359 p = wl->fw + FW_HDR_SIZE + chunk_num * CHUNK_SIZE; 360 wl1251_debug(DEBUG_BOOT, "uploading fw chunk 0x%p to 0x%x", 361 p, addr); 362 363 /* need to copy the chunk for dma */ 364 len = CHUNK_SIZE; 365 memcpy(buf, p, len); 366 wl1251_mem_write(wl, addr, buf, len); 367 368 chunk_num++; 369 } 370 371 /* 10.4 upload the last chunk */ 372 addr = WL1251_PART_DOWN_MEM_START + chunk_num * CHUNK_SIZE; 373 p = wl->fw + FW_HDR_SIZE + chunk_num * CHUNK_SIZE; 374 375 /* need to copy the chunk for dma */ 376 len = fw_data_len % CHUNK_SIZE; 377 memcpy(buf, p, len); 378 379 wl1251_debug(DEBUG_BOOT, "uploading fw last chunk (%zu B) 0x%p to 0x%x", 380 len, p, addr); 381 wl1251_mem_write(wl, addr, buf, len); 382 383 kfree(buf); 384 385 return 0; 386 } 387 388 static int wl1251_boot_upload_nvs(struct wl1251 *wl) 389 { 390 size_t nvs_len, nvs_bytes_written, burst_len; 391 int nvs_start, i; 392 u32 dest_addr, val; 393 u8 *nvs_ptr, *nvs; 394 395 nvs = wl->nvs; 396 if (nvs == NULL) 397 return -ENODEV; 398 399 nvs_ptr = nvs; 400 401 nvs_len = wl->nvs_len; 402 nvs_start = wl->fw_len; 403 404 /* 405 * Layout before the actual NVS tables: 406 * 1 byte : burst length. 407 * 2 bytes: destination address. 408 * n bytes: data to burst copy. 409 * 410 * This is ended by a 0 length, then the NVS tables. 411 */ 412 413 while (nvs_ptr[0]) { 414 burst_len = nvs_ptr[0]; 415 dest_addr = (nvs_ptr[1] & 0xfe) | ((u32)(nvs_ptr[2] << 8)); 416 417 /* We move our pointer to the data */ 418 nvs_ptr += 3; 419 420 for (i = 0; i < burst_len; i++) { 421 val = (nvs_ptr[0] | (nvs_ptr[1] << 8) 422 | (nvs_ptr[2] << 16) | (nvs_ptr[3] << 24)); 423 424 wl1251_debug(DEBUG_BOOT, 425 "nvs burst write 0x%x: 0x%x", 426 dest_addr, val); 427 wl1251_mem_write32(wl, dest_addr, val); 428 429 nvs_ptr += 4; 430 dest_addr += 4; 431 } 432 } 433 434 /* 435 * We've reached the first zero length, the first NVS table 436 * is 7 bytes further. 437 */ 438 nvs_ptr += 7; 439 nvs_len -= nvs_ptr - nvs; 440 nvs_len = ALIGN(nvs_len, 4); 441 442 /* Now we must set the partition correctly */ 443 wl1251_set_partition(wl, nvs_start, 444 WL1251_PART_DOWN_MEM_SIZE, 445 WL1251_PART_DOWN_REG_START, 446 WL1251_PART_DOWN_REG_SIZE); 447 448 /* And finally we upload the NVS tables */ 449 nvs_bytes_written = 0; 450 while (nvs_bytes_written < nvs_len) { 451 val = (nvs_ptr[0] | (nvs_ptr[1] << 8) 452 | (nvs_ptr[2] << 16) | (nvs_ptr[3] << 24)); 453 454 wl1251_debug(DEBUG_BOOT, 455 "nvs write table 0x%x: 0x%x", 456 nvs_start, val); 457 wl1251_mem_write32(wl, nvs_start, val); 458 459 nvs_ptr += 4; 460 nvs_bytes_written += 4; 461 nvs_start += 4; 462 } 463 464 return 0; 465 } 466 467 int wl1251_boot(struct wl1251 *wl) 468 { 469 int ret = 0, minor_minor_e2_ver; 470 u32 tmp, boot_data; 471 472 /* halt embedded ARM CPU while loading firmware */ 473 wl1251_reg_write32(wl, ACX_REG_ECPU_CONTROL, ECPU_CONTROL_HALT); 474 475 ret = wl1251_boot_soft_reset(wl); 476 if (ret < 0) 477 goto out; 478 479 /* 2. start processing NVS file */ 480 if (wl->use_eeprom) { 481 wl1251_reg_write32(wl, ACX_REG_EE_START, START_EEPROM_MGR); 482 /* Wait for EEPROM NVS burst read to complete */ 483 msleep(40); 484 wl1251_reg_write32(wl, ACX_EEPROMLESS_IND_REG, USE_EEPROM); 485 } else { 486 ret = wl1251_boot_upload_nvs(wl); 487 if (ret < 0) 488 goto out; 489 490 /* write firmware's last address (ie. it's length) to 491 * ACX_EEPROMLESS_IND_REG */ 492 wl1251_reg_write32(wl, ACX_EEPROMLESS_IND_REG, wl->fw_len); 493 } 494 495 /* 6. read the EEPROM parameters */ 496 tmp = wl1251_reg_read32(wl, SCR_PAD2); 497 498 /* 7. read bootdata */ 499 wl->boot_attr.radio_type = (tmp & 0x0000FF00) >> 8; 500 wl->boot_attr.major = (tmp & 0x00FF0000) >> 16; 501 tmp = wl1251_reg_read32(wl, SCR_PAD3); 502 503 /* 8. check bootdata and call restart sequence */ 504 wl->boot_attr.minor = (tmp & 0x00FF0000) >> 16; 505 minor_minor_e2_ver = (tmp & 0xFF000000) >> 24; 506 507 wl1251_debug(DEBUG_BOOT, "radioType 0x%x majorE2Ver 0x%x " 508 "minorE2Ver 0x%x minor_minor_e2_ver 0x%x", 509 wl->boot_attr.radio_type, wl->boot_attr.major, 510 wl->boot_attr.minor, minor_minor_e2_ver); 511 512 ret = wl1251_boot_init_seq(wl); 513 if (ret < 0) 514 goto out; 515 516 /* 9. NVS processing done */ 517 boot_data = wl1251_reg_read32(wl, ACX_REG_ECPU_CONTROL); 518 519 wl1251_debug(DEBUG_BOOT, "halt boot_data 0x%x", boot_data); 520 521 /* 10. check that ECPU_CONTROL_HALT bits are set in 522 * pWhalBus->uBootData and start uploading firmware 523 */ 524 if ((boot_data & ECPU_CONTROL_HALT) == 0) { 525 wl1251_error("boot failed, ECPU_CONTROL_HALT not set"); 526 ret = -EIO; 527 goto out; 528 } 529 530 ret = wl1251_boot_upload_firmware(wl); 531 if (ret < 0) 532 goto out; 533 534 /* 10.5 start firmware */ 535 ret = wl1251_boot_run_firmware(wl); 536 if (ret < 0) 537 goto out; 538 539 out: 540 return ret; 541 } 542