1 /* 2 * Copyright (c) 2014 Redpine Signals Inc. 3 * 4 * Permission to use, copy, modify, and/or distribute this software for any 5 * purpose with or without fee is hereby granted, provided that the above 6 * copyright notice and this permission notice appear in all copies. 7 * 8 * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES 9 * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF 10 * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR 11 * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES 12 * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN 13 * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF 14 * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. 15 * 16 */ 17 18 #include <linux/module.h> 19 #include <linux/types.h> 20 #include <net/rsi_91x.h> 21 #include "rsi_usb.h" 22 #include "rsi_hal.h" 23 #include "rsi_coex.h" 24 25 /* Default operating mode is wlan STA + BT */ 26 static u16 dev_oper_mode = DEV_OPMODE_STA_BT_DUAL; 27 module_param(dev_oper_mode, ushort, 0444); 28 MODULE_PARM_DESC(dev_oper_mode, 29 "1[Wi-Fi], 4[BT], 8[BT LE], 5[Wi-Fi STA + BT classic]\n" 30 "9[Wi-Fi STA + BT LE], 13[Wi-Fi STA + BT classic + BT LE]\n" 31 "6[AP + BT classic], 14[AP + BT classic + BT LE]"); 32 33 static int rsi_rx_urb_submit(struct rsi_hw *adapter, u8 ep_num, gfp_t flags); 34 35 /** 36 * rsi_usb_card_write() - This function writes to the USB Card. 37 * @adapter: Pointer to the adapter structure. 38 * @buf: Pointer to the buffer from where the data has to be taken. 39 * @len: Length to be written. 40 * @endpoint: Type of endpoint. 41 * 42 * Return: status: 0 on success, a negative error code on failure. 43 */ 44 static int rsi_usb_card_write(struct rsi_hw *adapter, 45 u8 *buf, 46 u16 len, 47 u8 endpoint) 48 { 49 struct rsi_91x_usbdev *dev = (struct rsi_91x_usbdev *)adapter->rsi_dev; 50 int status; 51 u8 *seg = dev->tx_buffer; 52 int transfer; 53 int ep = dev->bulkout_endpoint_addr[endpoint - 1]; 54 55 memset(seg, 0, len + RSI_USB_TX_HEAD_ROOM); 56 memcpy(seg + RSI_USB_TX_HEAD_ROOM, buf, len); 57 len += RSI_USB_TX_HEAD_ROOM; 58 transfer = len; 59 status = usb_bulk_msg(dev->usbdev, 60 usb_sndbulkpipe(dev->usbdev, ep), 61 (void *)seg, 62 (int)len, 63 &transfer, 64 HZ * 5); 65 66 if (status < 0) { 67 rsi_dbg(ERR_ZONE, 68 "Card write failed with error code :%10d\n", status); 69 dev->write_fail = 1; 70 } 71 return status; 72 } 73 74 /** 75 * rsi_write_multiple() - This function writes multiple bytes of information 76 * to the USB card. 77 * @adapter: Pointer to the adapter structure. 78 * @endpoint: Type of endpoint. 79 * @data: Pointer to the data that has to be written. 80 * @count: Number of multiple bytes to be written. 81 * 82 * Return: 0 on success, a negative error code on failure. 83 */ 84 static int rsi_write_multiple(struct rsi_hw *adapter, 85 u8 endpoint, 86 u8 *data, 87 u32 count) 88 { 89 struct rsi_91x_usbdev *dev; 90 91 if (!adapter) 92 return -ENODEV; 93 94 if (endpoint == 0) 95 return -EINVAL; 96 97 dev = (struct rsi_91x_usbdev *)adapter->rsi_dev; 98 if (dev->write_fail) 99 return -ENETDOWN; 100 101 return rsi_usb_card_write(adapter, data, count, endpoint); 102 } 103 104 /** 105 * rsi_find_bulk_in_and_out_endpoints() - This function initializes the bulk 106 * endpoints to the device. 107 * @interface: Pointer to the USB interface structure. 108 * @adapter: Pointer to the adapter structure. 109 * 110 * Return: ret_val: 0 on success, -ENOMEM on failure. 111 */ 112 static int rsi_find_bulk_in_and_out_endpoints(struct usb_interface *interface, 113 struct rsi_hw *adapter) 114 { 115 struct rsi_91x_usbdev *dev = (struct rsi_91x_usbdev *)adapter->rsi_dev; 116 struct usb_host_interface *iface_desc; 117 struct usb_endpoint_descriptor *endpoint; 118 __le16 buffer_size; 119 int ii, bin_found = 0, bout_found = 0; 120 121 iface_desc = interface->cur_altsetting; 122 123 for (ii = 0; ii < iface_desc->desc.bNumEndpoints; ++ii) { 124 endpoint = &(iface_desc->endpoint[ii].desc); 125 126 if (!dev->bulkin_endpoint_addr[bin_found] && 127 (endpoint->bEndpointAddress & USB_DIR_IN) && 128 ((endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) == 129 USB_ENDPOINT_XFER_BULK)) { 130 buffer_size = endpoint->wMaxPacketSize; 131 dev->bulkin_size[bin_found] = buffer_size; 132 dev->bulkin_endpoint_addr[bin_found] = 133 endpoint->bEndpointAddress; 134 bin_found++; 135 } 136 137 if (!dev->bulkout_endpoint_addr[bout_found] && 138 !(endpoint->bEndpointAddress & USB_DIR_IN) && 139 ((endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) == 140 USB_ENDPOINT_XFER_BULK)) { 141 buffer_size = endpoint->wMaxPacketSize; 142 dev->bulkout_endpoint_addr[bout_found] = 143 endpoint->bEndpointAddress; 144 dev->bulkout_size[bout_found] = buffer_size; 145 bout_found++; 146 } 147 148 if (bin_found >= MAX_BULK_EP || bout_found >= MAX_BULK_EP) 149 break; 150 } 151 152 if (!(dev->bulkin_endpoint_addr[0] && dev->bulkout_endpoint_addr[0])) { 153 dev_err(&interface->dev, "missing wlan bulk endpoints\n"); 154 return -EINVAL; 155 } 156 157 if (adapter->priv->coex_mode > 1) { 158 if (!dev->bulkin_endpoint_addr[1]) { 159 dev_err(&interface->dev, "missing bt bulk-in endpoint\n"); 160 return -EINVAL; 161 } 162 } 163 164 return 0; 165 } 166 167 #define RSI_USB_REQ_OUT (USB_TYPE_VENDOR | USB_DIR_OUT | USB_RECIP_DEVICE) 168 #define RSI_USB_REQ_IN (USB_TYPE_VENDOR | USB_DIR_IN | USB_RECIP_DEVICE) 169 170 /* rsi_usb_reg_read() - This function reads data from given register address. 171 * @usbdev: Pointer to the usb_device structure. 172 * @reg: Address of the register to be read. 173 * @value: Value to be read. 174 * @len: length of data to be read. 175 * 176 * Return: status: 0 on success, a negative error code on failure. 177 */ 178 static int rsi_usb_reg_read(struct usb_device *usbdev, 179 u32 reg, 180 u16 *value, 181 u16 len) 182 { 183 u8 *buf; 184 int status = -ENOMEM; 185 186 if (len > RSI_USB_CTRL_BUF_SIZE) 187 return -EINVAL; 188 189 buf = kmalloc(RSI_USB_CTRL_BUF_SIZE, GFP_KERNEL); 190 if (!buf) 191 return status; 192 193 status = usb_control_msg(usbdev, 194 usb_rcvctrlpipe(usbdev, 0), 195 USB_VENDOR_REGISTER_READ, 196 RSI_USB_REQ_IN, 197 ((reg & 0xffff0000) >> 16), (reg & 0xffff), 198 (void *)buf, 199 len, 200 USB_CTRL_GET_TIMEOUT); 201 202 *value = (buf[0] | (buf[1] << 8)); 203 if (status < 0) { 204 rsi_dbg(ERR_ZONE, 205 "%s: Reg read failed with error code :%d\n", 206 __func__, status); 207 } 208 kfree(buf); 209 210 return status; 211 } 212 213 /** 214 * rsi_usb_reg_write() - This function writes the given data into the given 215 * register address. 216 * @usbdev: Pointer to the usb_device structure. 217 * @reg: Address of the register. 218 * @value: Value to write. 219 * @len: Length of data to be written. 220 * 221 * Return: status: 0 on success, a negative error code on failure. 222 */ 223 static int rsi_usb_reg_write(struct usb_device *usbdev, 224 u32 reg, 225 u32 value, 226 u16 len) 227 { 228 u8 *usb_reg_buf; 229 int status = -ENOMEM; 230 231 if (len > RSI_USB_CTRL_BUF_SIZE) 232 return -EINVAL; 233 234 usb_reg_buf = kmalloc(RSI_USB_CTRL_BUF_SIZE, GFP_KERNEL); 235 if (!usb_reg_buf) 236 return status; 237 238 usb_reg_buf[0] = (cpu_to_le32(value) & 0x00ff); 239 usb_reg_buf[1] = (cpu_to_le32(value) & 0xff00) >> 8; 240 usb_reg_buf[2] = (cpu_to_le32(value) & 0x00ff0000) >> 16; 241 usb_reg_buf[3] = (cpu_to_le32(value) & 0xff000000) >> 24; 242 243 status = usb_control_msg(usbdev, 244 usb_sndctrlpipe(usbdev, 0), 245 USB_VENDOR_REGISTER_WRITE, 246 RSI_USB_REQ_OUT, 247 ((cpu_to_le32(reg) & 0xffff0000) >> 16), 248 (cpu_to_le32(reg) & 0xffff), 249 (void *)usb_reg_buf, 250 len, 251 USB_CTRL_SET_TIMEOUT); 252 if (status < 0) { 253 rsi_dbg(ERR_ZONE, 254 "%s: Reg write failed with error code :%d\n", 255 __func__, status); 256 } 257 kfree(usb_reg_buf); 258 259 return status; 260 } 261 262 /** 263 * rsi_rx_done_handler() - This function is called when a packet is received 264 * from USB stack. This is callback to receive done. 265 * @urb: Received URB. 266 * 267 * Return: None. 268 */ 269 static void rsi_rx_done_handler(struct urb *urb) 270 { 271 struct rx_usb_ctrl_block *rx_cb = urb->context; 272 struct rsi_91x_usbdev *dev = (struct rsi_91x_usbdev *)rx_cb->data; 273 int status = -EINVAL; 274 275 if (urb->status) { 276 dev_kfree_skb(rx_cb->rx_skb); 277 return; 278 } 279 280 if (urb->actual_length <= 0 || 281 urb->actual_length > rx_cb->rx_skb->len) { 282 rsi_dbg(INFO_ZONE, "%s: Invalid packet length = %d\n", 283 __func__, urb->actual_length); 284 goto out; 285 } 286 if (skb_queue_len(&dev->rx_q) >= RSI_MAX_RX_PKTS) { 287 rsi_dbg(INFO_ZONE, "Max RX packets reached\n"); 288 goto out; 289 } 290 skb_trim(rx_cb->rx_skb, urb->actual_length); 291 skb_queue_tail(&dev->rx_q, rx_cb->rx_skb); 292 293 rsi_set_event(&dev->rx_thread.event); 294 status = 0; 295 296 out: 297 if (rsi_rx_urb_submit(dev->priv, rx_cb->ep_num, GFP_ATOMIC)) 298 rsi_dbg(ERR_ZONE, "%s: Failed in urb submission", __func__); 299 300 if (status) 301 dev_kfree_skb(rx_cb->rx_skb); 302 } 303 304 static void rsi_rx_urb_kill(struct rsi_hw *adapter, u8 ep_num) 305 { 306 struct rsi_91x_usbdev *dev = (struct rsi_91x_usbdev *)adapter->rsi_dev; 307 struct rx_usb_ctrl_block *rx_cb = &dev->rx_cb[ep_num - 1]; 308 struct urb *urb = rx_cb->rx_urb; 309 310 usb_kill_urb(urb); 311 } 312 313 /** 314 * rsi_rx_urb_submit() - This function submits the given URB to the USB stack. 315 * @adapter: Pointer to the adapter structure. 316 * @ep_num: Endpoint number. 317 * @mem_flags: The type of memory to allocate. 318 * 319 * Return: 0 on success, a negative error code on failure. 320 */ 321 static int rsi_rx_urb_submit(struct rsi_hw *adapter, u8 ep_num, gfp_t mem_flags) 322 { 323 struct rsi_91x_usbdev *dev = (struct rsi_91x_usbdev *)adapter->rsi_dev; 324 struct rx_usb_ctrl_block *rx_cb = &dev->rx_cb[ep_num - 1]; 325 struct urb *urb = rx_cb->rx_urb; 326 int status; 327 struct sk_buff *skb; 328 u8 dword_align_bytes = 0; 329 330 #define RSI_MAX_RX_USB_PKT_SIZE 3000 331 skb = dev_alloc_skb(RSI_MAX_RX_USB_PKT_SIZE); 332 if (!skb) 333 return -ENOMEM; 334 skb_reserve(skb, MAX_DWORD_ALIGN_BYTES); 335 skb_put(skb, RSI_MAX_RX_USB_PKT_SIZE - MAX_DWORD_ALIGN_BYTES); 336 dword_align_bytes = (unsigned long)skb->data & 0x3f; 337 if (dword_align_bytes > 0) 338 skb_push(skb, dword_align_bytes); 339 urb->transfer_buffer = skb->data; 340 rx_cb->rx_skb = skb; 341 342 usb_fill_bulk_urb(urb, 343 dev->usbdev, 344 usb_rcvbulkpipe(dev->usbdev, 345 dev->bulkin_endpoint_addr[ep_num - 1]), 346 urb->transfer_buffer, 347 skb->len, 348 rsi_rx_done_handler, 349 rx_cb); 350 351 status = usb_submit_urb(urb, mem_flags); 352 if (status) { 353 rsi_dbg(ERR_ZONE, "%s: Failed in urb submission\n", __func__); 354 dev_kfree_skb(skb); 355 } 356 357 return status; 358 } 359 360 static int rsi_usb_read_register_multiple(struct rsi_hw *adapter, u32 addr, 361 u8 *data, u16 count) 362 { 363 struct rsi_91x_usbdev *dev = (struct rsi_91x_usbdev *)adapter->rsi_dev; 364 u8 *buf; 365 u16 transfer; 366 int status; 367 368 if (!addr) 369 return -EINVAL; 370 371 buf = kzalloc(RSI_USB_BUF_SIZE, GFP_KERNEL); 372 if (!buf) 373 return -ENOMEM; 374 375 while (count) { 376 transfer = min_t(u16, count, RSI_USB_BUF_SIZE); 377 status = usb_control_msg(dev->usbdev, 378 usb_rcvctrlpipe(dev->usbdev, 0), 379 USB_VENDOR_REGISTER_READ, 380 RSI_USB_REQ_IN, 381 ((addr & 0xffff0000) >> 16), 382 (addr & 0xffff), (void *)buf, 383 transfer, USB_CTRL_GET_TIMEOUT); 384 if (status < 0) { 385 rsi_dbg(ERR_ZONE, 386 "Reg read failed with error code :%d\n", 387 status); 388 kfree(buf); 389 return status; 390 } 391 memcpy(data, buf, transfer); 392 count -= transfer; 393 data += transfer; 394 addr += transfer; 395 } 396 kfree(buf); 397 return 0; 398 } 399 400 /** 401 * rsi_usb_write_register_multiple() - This function writes multiple bytes of 402 * information to multiple registers. 403 * @adapter: Pointer to the adapter structure. 404 * @addr: Address of the register. 405 * @data: Pointer to the data that has to be written. 406 * @count: Number of multiple bytes to be written on to the registers. 407 * 408 * Return: status: 0 on success, a negative error code on failure. 409 */ 410 static int rsi_usb_write_register_multiple(struct rsi_hw *adapter, u32 addr, 411 u8 *data, u16 count) 412 { 413 struct rsi_91x_usbdev *dev = (struct rsi_91x_usbdev *)adapter->rsi_dev; 414 u8 *buf; 415 u16 transfer; 416 int status = 0; 417 418 buf = kzalloc(RSI_USB_BUF_SIZE, GFP_KERNEL); 419 if (!buf) 420 return -ENOMEM; 421 422 while (count) { 423 transfer = min_t(u16, count, RSI_USB_BUF_SIZE); 424 memcpy(buf, data, transfer); 425 status = usb_control_msg(dev->usbdev, 426 usb_sndctrlpipe(dev->usbdev, 0), 427 USB_VENDOR_REGISTER_WRITE, 428 RSI_USB_REQ_OUT, 429 ((addr & 0xffff0000) >> 16), 430 (addr & 0xffff), 431 (void *)buf, 432 transfer, 433 USB_CTRL_SET_TIMEOUT); 434 if (status < 0) { 435 rsi_dbg(ERR_ZONE, 436 "Reg write failed with error code :%d\n", 437 status); 438 kfree(buf); 439 return status; 440 } 441 count -= transfer; 442 data += transfer; 443 addr += transfer; 444 } 445 446 kfree(buf); 447 return 0; 448 } 449 450 /** 451 *rsi_usb_host_intf_write_pkt() - This function writes the packet to the 452 * USB card. 453 * @adapter: Pointer to the adapter structure. 454 * @pkt: Pointer to the data to be written on to the card. 455 * @len: Length of the data to be written on to the card. 456 * 457 * Return: 0 on success, a negative error code on failure. 458 */ 459 static int rsi_usb_host_intf_write_pkt(struct rsi_hw *adapter, 460 u8 *pkt, 461 u32 len) 462 { 463 u32 queueno = ((pkt[1] >> 4) & 0x7); 464 u8 endpoint; 465 466 endpoint = ((queueno == RSI_WIFI_MGMT_Q || queueno == RSI_WIFI_DATA_Q || 467 queueno == RSI_COEX_Q) ? WLAN_EP : BT_EP); 468 469 return rsi_write_multiple(adapter, 470 endpoint, 471 (u8 *)pkt, 472 len); 473 } 474 475 static int rsi_usb_master_reg_read(struct rsi_hw *adapter, u32 reg, 476 u32 *value, u16 len) 477 { 478 struct usb_device *usbdev = 479 ((struct rsi_91x_usbdev *)adapter->rsi_dev)->usbdev; 480 u16 temp; 481 int ret; 482 483 ret = rsi_usb_reg_read(usbdev, reg, &temp, len); 484 if (ret < 0) 485 return ret; 486 *value = temp; 487 488 return 0; 489 } 490 491 static int rsi_usb_master_reg_write(struct rsi_hw *adapter, 492 unsigned long reg, 493 unsigned long value, u16 len) 494 { 495 struct usb_device *usbdev = 496 ((struct rsi_91x_usbdev *)adapter->rsi_dev)->usbdev; 497 498 return rsi_usb_reg_write(usbdev, reg, value, len); 499 } 500 501 static int rsi_usb_load_data_master_write(struct rsi_hw *adapter, 502 u32 base_address, 503 u32 instructions_sz, u16 block_size, 504 u8 *ta_firmware) 505 { 506 u16 num_blocks; 507 u32 cur_indx, i; 508 u8 temp_buf[256]; 509 int status; 510 511 num_blocks = instructions_sz / block_size; 512 rsi_dbg(INFO_ZONE, "num_blocks: %d\n", num_blocks); 513 514 for (cur_indx = 0, i = 0; i < num_blocks; i++, cur_indx += block_size) { 515 memcpy(temp_buf, ta_firmware + cur_indx, block_size); 516 status = rsi_usb_write_register_multiple(adapter, base_address, 517 (u8 *)(temp_buf), 518 block_size); 519 if (status < 0) 520 return status; 521 522 rsi_dbg(INFO_ZONE, "%s: loading block: %d\n", __func__, i); 523 base_address += block_size; 524 } 525 526 if (instructions_sz % block_size) { 527 memset(temp_buf, 0, block_size); 528 memcpy(temp_buf, ta_firmware + cur_indx, 529 instructions_sz % block_size); 530 status = rsi_usb_write_register_multiple 531 (adapter, base_address, 532 (u8 *)temp_buf, 533 instructions_sz % block_size); 534 if (status < 0) 535 return status; 536 rsi_dbg(INFO_ZONE, 537 "Written Last Block in Address 0x%x Successfully\n", 538 cur_indx); 539 } 540 return 0; 541 } 542 543 static struct rsi_host_intf_ops usb_host_intf_ops = { 544 .write_pkt = rsi_usb_host_intf_write_pkt, 545 .read_reg_multiple = rsi_usb_read_register_multiple, 546 .write_reg_multiple = rsi_usb_write_register_multiple, 547 .master_reg_read = rsi_usb_master_reg_read, 548 .master_reg_write = rsi_usb_master_reg_write, 549 .load_data_master_write = rsi_usb_load_data_master_write, 550 }; 551 552 /** 553 * rsi_deinit_usb_interface() - This function deinitializes the usb interface. 554 * @adapter: Pointer to the adapter structure. 555 * 556 * Return: None. 557 */ 558 static void rsi_deinit_usb_interface(struct rsi_hw *adapter) 559 { 560 struct rsi_91x_usbdev *dev = (struct rsi_91x_usbdev *)adapter->rsi_dev; 561 562 rsi_kill_thread(&dev->rx_thread); 563 564 usb_free_urb(dev->rx_cb[0].rx_urb); 565 if (adapter->priv->coex_mode > 1) 566 usb_free_urb(dev->rx_cb[1].rx_urb); 567 568 kfree(dev->tx_buffer); 569 } 570 571 static int rsi_usb_init_rx(struct rsi_hw *adapter) 572 { 573 struct rsi_91x_usbdev *dev = (struct rsi_91x_usbdev *)adapter->rsi_dev; 574 struct rx_usb_ctrl_block *rx_cb; 575 u8 idx, num_rx_cb; 576 577 num_rx_cb = (adapter->priv->coex_mode > 1 ? 2 : 1); 578 579 for (idx = 0; idx < num_rx_cb; idx++) { 580 rx_cb = &dev->rx_cb[idx]; 581 582 rx_cb->rx_urb = usb_alloc_urb(0, GFP_KERNEL); 583 if (!rx_cb->rx_urb) { 584 rsi_dbg(ERR_ZONE, "Failed alloc rx urb[%d]\n", idx); 585 goto err; 586 } 587 rx_cb->ep_num = idx + 1; 588 rx_cb->data = (void *)dev; 589 } 590 skb_queue_head_init(&dev->rx_q); 591 rsi_init_event(&dev->rx_thread.event); 592 if (rsi_create_kthread(adapter->priv, &dev->rx_thread, 593 rsi_usb_rx_thread, "RX-Thread")) { 594 rsi_dbg(ERR_ZONE, "%s: Unable to init rx thrd\n", __func__); 595 goto err; 596 } 597 598 return 0; 599 600 err: 601 usb_free_urb(dev->rx_cb[0].rx_urb); 602 if (adapter->priv->coex_mode > 1) 603 usb_free_urb(dev->rx_cb[1].rx_urb); 604 605 return -1; 606 } 607 608 /** 609 * rsi_init_usb_interface() - This function initializes the usb interface. 610 * @adapter: Pointer to the adapter structure. 611 * @pfunction: Pointer to USB interface structure. 612 * 613 * Return: 0 on success, a negative error code on failure. 614 */ 615 static int rsi_init_usb_interface(struct rsi_hw *adapter, 616 struct usb_interface *pfunction) 617 { 618 struct rsi_91x_usbdev *rsi_dev; 619 int status; 620 621 rsi_dev = kzalloc(sizeof(*rsi_dev), GFP_KERNEL); 622 if (!rsi_dev) 623 return -ENOMEM; 624 625 adapter->rsi_dev = rsi_dev; 626 rsi_dev->usbdev = interface_to_usbdev(pfunction); 627 rsi_dev->priv = (void *)adapter; 628 629 if (rsi_find_bulk_in_and_out_endpoints(pfunction, adapter)) { 630 status = -EINVAL; 631 goto fail_eps; 632 } 633 634 adapter->device = &pfunction->dev; 635 usb_set_intfdata(pfunction, adapter); 636 637 rsi_dev->tx_buffer = kmalloc(2048, GFP_KERNEL); 638 if (!rsi_dev->tx_buffer) { 639 status = -ENOMEM; 640 goto fail_eps; 641 } 642 643 if (rsi_usb_init_rx(adapter)) { 644 rsi_dbg(ERR_ZONE, "Failed to init RX handle\n"); 645 status = -ENOMEM; 646 goto fail_rx; 647 } 648 649 rsi_dev->tx_blk_size = 252; 650 adapter->block_size = rsi_dev->tx_blk_size; 651 652 /* Initializing function callbacks */ 653 adapter->check_hw_queue_status = rsi_usb_check_queue_status; 654 adapter->determine_event_timeout = rsi_usb_event_timeout; 655 adapter->rsi_host_intf = RSI_HOST_INTF_USB; 656 adapter->host_intf_ops = &usb_host_intf_ops; 657 658 #ifdef CONFIG_RSI_DEBUGFS 659 /* In USB, one less than the MAX_DEBUGFS_ENTRIES entries is required */ 660 adapter->num_debugfs_entries = (MAX_DEBUGFS_ENTRIES - 1); 661 #endif 662 663 rsi_dbg(INIT_ZONE, "%s: Enabled the interface\n", __func__); 664 return 0; 665 666 fail_rx: 667 kfree(rsi_dev->tx_buffer); 668 669 fail_eps: 670 671 return status; 672 } 673 674 static int usb_ulp_read_write(struct rsi_hw *adapter, u16 addr, u32 data, 675 u16 len_in_bits) 676 { 677 int ret; 678 679 ret = rsi_usb_master_reg_write 680 (adapter, RSI_GSPI_DATA_REG1, 681 ((addr << 6) | ((data >> 16) & 0xffff)), 2); 682 if (ret < 0) 683 return ret; 684 685 ret = rsi_usb_master_reg_write(adapter, RSI_GSPI_DATA_REG0, 686 (data & 0xffff), 2); 687 if (ret < 0) 688 return ret; 689 690 /* Initializing GSPI for ULP read/writes */ 691 rsi_usb_master_reg_write(adapter, RSI_GSPI_CTRL_REG0, 692 RSI_GSPI_CTRL_REG0_VALUE, 2); 693 694 ret = rsi_usb_master_reg_write(adapter, RSI_GSPI_CTRL_REG1, 695 ((len_in_bits - 1) | RSI_GSPI_TRIG), 2); 696 if (ret < 0) 697 return ret; 698 699 msleep(20); 700 701 return 0; 702 } 703 704 static int rsi_reset_card(struct rsi_hw *adapter) 705 { 706 int ret; 707 708 rsi_dbg(INFO_ZONE, "Resetting Card...\n"); 709 rsi_usb_master_reg_write(adapter, RSI_TA_HOLD_REG, 0xE, 4); 710 711 /* This msleep will ensure Thread-Arch processor to go to hold 712 * and any pending dma transfers to rf in device to finish. 713 */ 714 msleep(100); 715 716 ret = rsi_usb_master_reg_write(adapter, SWBL_REGOUT, 717 RSI_FW_WDT_DISABLE_REQ, 718 RSI_COMMON_REG_SIZE); 719 if (ret < 0) { 720 rsi_dbg(ERR_ZONE, "Disabling firmware watchdog timer failed\n"); 721 goto fail; 722 } 723 724 if (adapter->device_model != RSI_DEV_9116) { 725 ret = usb_ulp_read_write(adapter, RSI_WATCH_DOG_TIMER_1, 726 RSI_ULP_WRITE_2, 32); 727 if (ret < 0) 728 goto fail; 729 ret = usb_ulp_read_write(adapter, RSI_WATCH_DOG_TIMER_2, 730 RSI_ULP_WRITE_0, 32); 731 if (ret < 0) 732 goto fail; 733 ret = usb_ulp_read_write(adapter, RSI_WATCH_DOG_DELAY_TIMER_1, 734 RSI_ULP_WRITE_50, 32); 735 if (ret < 0) 736 goto fail; 737 ret = usb_ulp_read_write(adapter, RSI_WATCH_DOG_DELAY_TIMER_2, 738 RSI_ULP_WRITE_0, 32); 739 if (ret < 0) 740 goto fail; 741 ret = usb_ulp_read_write(adapter, RSI_WATCH_DOG_TIMER_ENABLE, 742 RSI_ULP_TIMER_ENABLE, 32); 743 if (ret < 0) 744 goto fail; 745 } else { 746 ret = rsi_usb_master_reg_write(adapter, 747 NWP_WWD_INTERRUPT_TIMER, 748 NWP_WWD_INT_TIMER_CLKS, 749 RSI_9116_REG_SIZE); 750 if (ret < 0) 751 goto fail; 752 ret = rsi_usb_master_reg_write(adapter, 753 NWP_WWD_SYSTEM_RESET_TIMER, 754 NWP_WWD_SYS_RESET_TIMER_CLKS, 755 RSI_9116_REG_SIZE); 756 if (ret < 0) 757 goto fail; 758 ret = rsi_usb_master_reg_write(adapter, 759 NWP_WWD_MODE_AND_RSTART, 760 NWP_WWD_TIMER_DISABLE, 761 RSI_9116_REG_SIZE); 762 if (ret < 0) 763 goto fail; 764 } 765 766 rsi_dbg(INFO_ZONE, "Reset card done\n"); 767 return ret; 768 769 fail: 770 rsi_dbg(ERR_ZONE, "Reset card failed\n"); 771 return ret; 772 } 773 774 /** 775 * rsi_probe() - This function is called by kernel when the driver provided 776 * Vendor and device IDs are matched. All the initialization 777 * work is done here. 778 * @pfunction: Pointer to the USB interface structure. 779 * @id: Pointer to the usb_device_id structure. 780 * 781 * Return: 0 on success, a negative error code on failure. 782 */ 783 static int rsi_probe(struct usb_interface *pfunction, 784 const struct usb_device_id *id) 785 { 786 struct rsi_hw *adapter; 787 struct rsi_91x_usbdev *dev; 788 u16 fw_status; 789 int status; 790 791 rsi_dbg(INIT_ZONE, "%s: Init function called\n", __func__); 792 793 adapter = rsi_91x_init(dev_oper_mode); 794 if (!adapter) { 795 rsi_dbg(ERR_ZONE, "%s: Failed to init os intf ops\n", 796 __func__); 797 return -ENOMEM; 798 } 799 adapter->rsi_host_intf = RSI_HOST_INTF_USB; 800 801 status = rsi_init_usb_interface(adapter, pfunction); 802 if (status) { 803 rsi_dbg(ERR_ZONE, "%s: Failed to init usb interface\n", 804 __func__); 805 goto err; 806 } 807 808 rsi_dbg(ERR_ZONE, "%s: Initialized os intf ops\n", __func__); 809 810 if (id->idProduct == RSI_USB_PID_9113) { 811 rsi_dbg(INIT_ZONE, "%s: 9113 module detected\n", __func__); 812 adapter->device_model = RSI_DEV_9113; 813 } else if (id->idProduct == RSI_USB_PID_9116) { 814 rsi_dbg(INIT_ZONE, "%s: 9116 module detected\n", __func__); 815 adapter->device_model = RSI_DEV_9116; 816 } else { 817 rsi_dbg(ERR_ZONE, "%s: Unsupported RSI device id 0x%x\n", 818 __func__, id->idProduct); 819 goto err1; 820 } 821 822 dev = (struct rsi_91x_usbdev *)adapter->rsi_dev; 823 824 status = rsi_usb_reg_read(dev->usbdev, FW_STATUS_REG, &fw_status, 2); 825 if (status < 0) 826 goto err1; 827 else 828 fw_status &= 1; 829 830 if (!fw_status) { 831 rsi_dbg(INIT_ZONE, "Loading firmware...\n"); 832 status = rsi_hal_device_init(adapter); 833 if (status) { 834 rsi_dbg(ERR_ZONE, "%s: Failed in device init\n", 835 __func__); 836 goto err1; 837 } 838 rsi_dbg(INIT_ZONE, "%s: Device Init Done\n", __func__); 839 } 840 841 status = rsi_rx_urb_submit(adapter, WLAN_EP, GFP_KERNEL); 842 if (status) 843 goto err1; 844 845 if (adapter->priv->coex_mode > 1) { 846 status = rsi_rx_urb_submit(adapter, BT_EP, GFP_KERNEL); 847 if (status) 848 goto err_kill_wlan_urb; 849 } 850 851 return 0; 852 853 err_kill_wlan_urb: 854 rsi_rx_urb_kill(adapter, WLAN_EP); 855 err1: 856 rsi_deinit_usb_interface(adapter); 857 err: 858 rsi_91x_deinit(adapter); 859 rsi_dbg(ERR_ZONE, "%s: Failed in probe...Exiting\n", __func__); 860 return status; 861 } 862 863 /** 864 * rsi_disconnect() - This function performs the reverse of the probe function, 865 * it deinitialize the driver structure. 866 * @pfunction: Pointer to the USB interface structure. 867 * 868 * Return: None. 869 */ 870 static void rsi_disconnect(struct usb_interface *pfunction) 871 { 872 struct rsi_hw *adapter = usb_get_intfdata(pfunction); 873 874 if (!adapter) 875 return; 876 877 rsi_mac80211_detach(adapter); 878 879 if (IS_ENABLED(CONFIG_RSI_COEX) && adapter->priv->coex_mode > 1 && 880 adapter->priv->bt_adapter) { 881 rsi_bt_ops.detach(adapter->priv->bt_adapter); 882 adapter->priv->bt_adapter = NULL; 883 } 884 885 if (adapter->priv->coex_mode > 1) 886 rsi_rx_urb_kill(adapter, BT_EP); 887 rsi_rx_urb_kill(adapter, WLAN_EP); 888 889 rsi_reset_card(adapter); 890 rsi_deinit_usb_interface(adapter); 891 rsi_91x_deinit(adapter); 892 893 rsi_dbg(INFO_ZONE, "%s: Deinitialization completed\n", __func__); 894 } 895 896 #ifdef CONFIG_PM 897 static int rsi_suspend(struct usb_interface *intf, pm_message_t message) 898 { 899 /* Not yet implemented */ 900 return -ENOSYS; 901 } 902 903 static int rsi_resume(struct usb_interface *intf) 904 { 905 /* Not yet implemented */ 906 return -ENOSYS; 907 } 908 #endif 909 910 static const struct usb_device_id rsi_dev_table[] = { 911 { USB_DEVICE(RSI_USB_VENDOR_ID, RSI_USB_PID_9113) }, 912 { USB_DEVICE(RSI_USB_VENDOR_ID, RSI_USB_PID_9116) }, 913 { /* Blank */}, 914 }; 915 916 static struct usb_driver rsi_driver = { 917 .name = "RSI-USB WLAN", 918 .probe = rsi_probe, 919 .disconnect = rsi_disconnect, 920 .id_table = rsi_dev_table, 921 #ifdef CONFIG_PM 922 .suspend = rsi_suspend, 923 .resume = rsi_resume, 924 #endif 925 }; 926 927 module_usb_driver(rsi_driver); 928 929 MODULE_AUTHOR("Redpine Signals Inc"); 930 MODULE_DESCRIPTION("Common USB layer for RSI drivers"); 931 MODULE_DEVICE_TABLE(usb, rsi_dev_table); 932 MODULE_FIRMWARE(FIRMWARE_RSI9113); 933 MODULE_VERSION("0.1"); 934 MODULE_LICENSE("Dual BSD/GPL"); 935