1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3  * RTL8XXXU mac80211 USB driver - 8723b specific subdriver
4  *
5  * Copyright (c) 2014 - 2017 Jes Sorensen <Jes.Sorensen@gmail.com>
6  *
7  * Portions, notably calibration code:
8  * Copyright(c) 2007 - 2011 Realtek Corporation. All rights reserved.
9  *
10  * This driver was written as a replacement for the vendor provided
11  * rtl8723au driver. As the Realtek 8xxx chips are very similar in
12  * their programming interface, I have started adding support for
13  * additional 8xxx chips like the 8192cu, 8188cus, etc.
14  */
15 
16 #include <linux/init.h>
17 #include <linux/kernel.h>
18 #include <linux/sched.h>
19 #include <linux/errno.h>
20 #include <linux/slab.h>
21 #include <linux/module.h>
22 #include <linux/spinlock.h>
23 #include <linux/list.h>
24 #include <linux/usb.h>
25 #include <linux/netdevice.h>
26 #include <linux/etherdevice.h>
27 #include <linux/ethtool.h>
28 #include <linux/wireless.h>
29 #include <linux/firmware.h>
30 #include <linux/moduleparam.h>
31 #include <net/mac80211.h>
32 #include "rtl8xxxu.h"
33 #include "rtl8xxxu_regs.h"
34 
35 static struct rtl8xxxu_reg8val rtl8723b_mac_init_table[] = {
36 	{0x02f, 0x30}, {0x035, 0x00}, {0x039, 0x08}, {0x04e, 0xe0},
37 	{0x064, 0x00}, {0x067, 0x20}, {0x428, 0x0a}, {0x429, 0x10},
38 	{0x430, 0x00}, {0x431, 0x00},
39 	{0x432, 0x00}, {0x433, 0x01}, {0x434, 0x04}, {0x435, 0x05},
40 	{0x436, 0x07}, {0x437, 0x08}, {0x43c, 0x04}, {0x43d, 0x05},
41 	{0x43e, 0x07}, {0x43f, 0x08}, {0x440, 0x5d}, {0x441, 0x01},
42 	{0x442, 0x00}, {0x444, 0x10}, {0x445, 0x00}, {0x446, 0x00},
43 	{0x447, 0x00}, {0x448, 0x00}, {0x449, 0xf0}, {0x44a, 0x0f},
44 	{0x44b, 0x3e}, {0x44c, 0x10}, {0x44d, 0x00}, {0x44e, 0x00},
45 	{0x44f, 0x00}, {0x450, 0x00}, {0x451, 0xf0}, {0x452, 0x0f},
46 	{0x453, 0x00}, {0x456, 0x5e}, {0x460, 0x66}, {0x461, 0x66},
47 	{0x4c8, 0xff}, {0x4c9, 0x08}, {0x4cc, 0xff},
48 	{0x4cd, 0xff}, {0x4ce, 0x01}, {0x500, 0x26}, {0x501, 0xa2},
49 	{0x502, 0x2f}, {0x503, 0x00}, {0x504, 0x28}, {0x505, 0xa3},
50 	{0x506, 0x5e}, {0x507, 0x00}, {0x508, 0x2b}, {0x509, 0xa4},
51 	{0x50a, 0x5e}, {0x50b, 0x00}, {0x50c, 0x4f}, {0x50d, 0xa4},
52 	{0x50e, 0x00}, {0x50f, 0x00}, {0x512, 0x1c}, {0x514, 0x0a},
53 	{0x516, 0x0a}, {0x525, 0x4f},
54 	{0x550, 0x10}, {0x551, 0x10}, {0x559, 0x02}, {0x55c, 0x50},
55 	{0x55d, 0xff}, {0x605, 0x30}, {0x608, 0x0e}, {0x609, 0x2a},
56 	{0x620, 0xff}, {0x621, 0xff}, {0x622, 0xff}, {0x623, 0xff},
57 	{0x624, 0xff}, {0x625, 0xff}, {0x626, 0xff}, {0x627, 0xff},
58 	{0x638, 0x50}, {0x63c, 0x0a}, {0x63d, 0x0a}, {0x63e, 0x0e},
59 	{0x63f, 0x0e}, {0x640, 0x40}, {0x642, 0x40}, {0x643, 0x00},
60 	{0x652, 0xc8}, {0x66e, 0x05}, {0x700, 0x21}, {0x701, 0x43},
61 	{0x702, 0x65}, {0x703, 0x87}, {0x708, 0x21}, {0x709, 0x43},
62 	{0x70a, 0x65}, {0x70b, 0x87}, {0x765, 0x18}, {0x76e, 0x04},
63 	{0xffff, 0xff},
64 };
65 
66 static struct rtl8xxxu_reg32val rtl8723b_phy_1t_init_table[] = {
67 	{0x800, 0x80040000}, {0x804, 0x00000003},
68 	{0x808, 0x0000fc00}, {0x80c, 0x0000000a},
69 	{0x810, 0x10001331}, {0x814, 0x020c3d10},
70 	{0x818, 0x02200385}, {0x81c, 0x00000000},
71 	{0x820, 0x01000100}, {0x824, 0x00190204},
72 	{0x828, 0x00000000}, {0x82c, 0x00000000},
73 	{0x830, 0x00000000}, {0x834, 0x00000000},
74 	{0x838, 0x00000000}, {0x83c, 0x00000000},
75 	{0x840, 0x00010000}, {0x844, 0x00000000},
76 	{0x848, 0x00000000}, {0x84c, 0x00000000},
77 	{0x850, 0x00000000}, {0x854, 0x00000000},
78 	{0x858, 0x569a11a9}, {0x85c, 0x01000014},
79 	{0x860, 0x66f60110}, {0x864, 0x061f0649},
80 	{0x868, 0x00000000}, {0x86c, 0x27272700},
81 	{0x870, 0x07000760}, {0x874, 0x25004000},
82 	{0x878, 0x00000808}, {0x87c, 0x00000000},
83 	{0x880, 0xb0000c1c}, {0x884, 0x00000001},
84 	{0x888, 0x00000000}, {0x88c, 0xccc000c0},
85 	{0x890, 0x00000800}, {0x894, 0xfffffffe},
86 	{0x898, 0x40302010}, {0x89c, 0x00706050},
87 	{0x900, 0x00000000}, {0x904, 0x00000023},
88 	{0x908, 0x00000000}, {0x90c, 0x81121111},
89 	{0x910, 0x00000002}, {0x914, 0x00000201},
90 	{0xa00, 0x00d047c8}, {0xa04, 0x80ff800c},
91 	{0xa08, 0x8c838300}, {0xa0c, 0x2e7f120f},
92 	{0xa10, 0x9500bb78}, {0xa14, 0x1114d028},
93 	{0xa18, 0x00881117}, {0xa1c, 0x89140f00},
94 	{0xa20, 0x1a1b0000}, {0xa24, 0x090e1317},
95 	{0xa28, 0x00000204}, {0xa2c, 0x00d30000},
96 	{0xa70, 0x101fbf00}, {0xa74, 0x00000007},
97 	{0xa78, 0x00000900}, {0xa7c, 0x225b0606},
98 	{0xa80, 0x21806490}, {0xb2c, 0x00000000},
99 	{0xc00, 0x48071d40}, {0xc04, 0x03a05611},
100 	{0xc08, 0x000000e4}, {0xc0c, 0x6c6c6c6c},
101 	{0xc10, 0x08800000}, {0xc14, 0x40000100},
102 	{0xc18, 0x08800000}, {0xc1c, 0x40000100},
103 	{0xc20, 0x00000000}, {0xc24, 0x00000000},
104 	{0xc28, 0x00000000}, {0xc2c, 0x00000000},
105 	{0xc30, 0x69e9ac44}, {0xc34, 0x469652af},
106 	{0xc38, 0x49795994}, {0xc3c, 0x0a97971c},
107 	{0xc40, 0x1f7c403f}, {0xc44, 0x000100b7},
108 	{0xc48, 0xec020107}, {0xc4c, 0x007f037f},
109 	{0xc50, 0x69553420}, {0xc54, 0x43bc0094},
110 	{0xc58, 0x00013149}, {0xc5c, 0x00250492},
111 	{0xc60, 0x00000000}, {0xc64, 0x7112848b},
112 	{0xc68, 0x47c00bff}, {0xc6c, 0x00000036},
113 	{0xc70, 0x2c7f000d}, {0xc74, 0x020610db},
114 	{0xc78, 0x0000001f}, {0xc7c, 0x00b91612},
115 	{0xc80, 0x390000e4}, {0xc84, 0x20f60000},
116 	{0xc88, 0x40000100}, {0xc8c, 0x20200000},
117 	{0xc90, 0x00020e1a}, {0xc94, 0x00000000},
118 	{0xc98, 0x00020e1a}, {0xc9c, 0x00007f7f},
119 	{0xca0, 0x00000000}, {0xca4, 0x000300a0},
120 	{0xca8, 0x00000000}, {0xcac, 0x00000000},
121 	{0xcb0, 0x00000000}, {0xcb4, 0x00000000},
122 	{0xcb8, 0x00000000}, {0xcbc, 0x28000000},
123 	{0xcc0, 0x00000000}, {0xcc4, 0x00000000},
124 	{0xcc8, 0x00000000}, {0xccc, 0x00000000},
125 	{0xcd0, 0x00000000}, {0xcd4, 0x00000000},
126 	{0xcd8, 0x64b22427}, {0xcdc, 0x00766932},
127 	{0xce0, 0x00222222}, {0xce4, 0x00000000},
128 	{0xce8, 0x37644302}, {0xcec, 0x2f97d40c},
129 	{0xd00, 0x00000740}, {0xd04, 0x40020401},
130 	{0xd08, 0x0000907f}, {0xd0c, 0x20010201},
131 	{0xd10, 0xa0633333}, {0xd14, 0x3333bc53},
132 	{0xd18, 0x7a8f5b6f}, {0xd2c, 0xcc979975},
133 	{0xd30, 0x00000000}, {0xd34, 0x80608000},
134 	{0xd38, 0x00000000}, {0xd3c, 0x00127353},
135 	{0xd40, 0x00000000}, {0xd44, 0x00000000},
136 	{0xd48, 0x00000000}, {0xd4c, 0x00000000},
137 	{0xd50, 0x6437140a}, {0xd54, 0x00000000},
138 	{0xd58, 0x00000282}, {0xd5c, 0x30032064},
139 	{0xd60, 0x4653de68}, {0xd64, 0x04518a3c},
140 	{0xd68, 0x00002101}, {0xd6c, 0x2a201c16},
141 	{0xd70, 0x1812362e}, {0xd74, 0x322c2220},
142 	{0xd78, 0x000e3c24}, {0xe00, 0x2d2d2d2d},
143 	{0xe04, 0x2d2d2d2d}, {0xe08, 0x0390272d},
144 	{0xe10, 0x2d2d2d2d}, {0xe14, 0x2d2d2d2d},
145 	{0xe18, 0x2d2d2d2d}, {0xe1c, 0x2d2d2d2d},
146 	{0xe28, 0x00000000}, {0xe30, 0x1000dc1f},
147 	{0xe34, 0x10008c1f}, {0xe38, 0x02140102},
148 	{0xe3c, 0x681604c2}, {0xe40, 0x01007c00},
149 	{0xe44, 0x01004800}, {0xe48, 0xfb000000},
150 	{0xe4c, 0x000028d1}, {0xe50, 0x1000dc1f},
151 	{0xe54, 0x10008c1f}, {0xe58, 0x02140102},
152 	{0xe5c, 0x28160d05}, {0xe60, 0x00000008},
153 	{0xe68, 0x001b2556}, {0xe6c, 0x00c00096},
154 	{0xe70, 0x00c00096}, {0xe74, 0x01000056},
155 	{0xe78, 0x01000014}, {0xe7c, 0x01000056},
156 	{0xe80, 0x01000014}, {0xe84, 0x00c00096},
157 	{0xe88, 0x01000056}, {0xe8c, 0x00c00096},
158 	{0xed0, 0x00c00096}, {0xed4, 0x00c00096},
159 	{0xed8, 0x00c00096}, {0xedc, 0x000000d6},
160 	{0xee0, 0x000000d6}, {0xeec, 0x01c00016},
161 	{0xf14, 0x00000003}, {0xf4c, 0x00000000},
162 	{0xf00, 0x00000300},
163 	{0x820, 0x01000100}, {0x800, 0x83040000},
164 	{0xffff, 0xffffffff},
165 };
166 
167 static struct rtl8xxxu_reg32val rtl8xxx_agc_8723bu_table[] = {
168 	{0xc78, 0xfd000001}, {0xc78, 0xfc010001},
169 	{0xc78, 0xfb020001}, {0xc78, 0xfa030001},
170 	{0xc78, 0xf9040001}, {0xc78, 0xf8050001},
171 	{0xc78, 0xf7060001}, {0xc78, 0xf6070001},
172 	{0xc78, 0xf5080001}, {0xc78, 0xf4090001},
173 	{0xc78, 0xf30a0001}, {0xc78, 0xf20b0001},
174 	{0xc78, 0xf10c0001}, {0xc78, 0xf00d0001},
175 	{0xc78, 0xef0e0001}, {0xc78, 0xee0f0001},
176 	{0xc78, 0xed100001}, {0xc78, 0xec110001},
177 	{0xc78, 0xeb120001}, {0xc78, 0xea130001},
178 	{0xc78, 0xe9140001}, {0xc78, 0xe8150001},
179 	{0xc78, 0xe7160001}, {0xc78, 0xe6170001},
180 	{0xc78, 0xe5180001}, {0xc78, 0xe4190001},
181 	{0xc78, 0xe31a0001}, {0xc78, 0xa51b0001},
182 	{0xc78, 0xa41c0001}, {0xc78, 0xa31d0001},
183 	{0xc78, 0x671e0001}, {0xc78, 0x661f0001},
184 	{0xc78, 0x65200001}, {0xc78, 0x64210001},
185 	{0xc78, 0x63220001}, {0xc78, 0x4a230001},
186 	{0xc78, 0x49240001}, {0xc78, 0x48250001},
187 	{0xc78, 0x47260001}, {0xc78, 0x46270001},
188 	{0xc78, 0x45280001}, {0xc78, 0x44290001},
189 	{0xc78, 0x432a0001}, {0xc78, 0x422b0001},
190 	{0xc78, 0x292c0001}, {0xc78, 0x282d0001},
191 	{0xc78, 0x272e0001}, {0xc78, 0x262f0001},
192 	{0xc78, 0x0a300001}, {0xc78, 0x09310001},
193 	{0xc78, 0x08320001}, {0xc78, 0x07330001},
194 	{0xc78, 0x06340001}, {0xc78, 0x05350001},
195 	{0xc78, 0x04360001}, {0xc78, 0x03370001},
196 	{0xc78, 0x02380001}, {0xc78, 0x01390001},
197 	{0xc78, 0x013a0001}, {0xc78, 0x013b0001},
198 	{0xc78, 0x013c0001}, {0xc78, 0x013d0001},
199 	{0xc78, 0x013e0001}, {0xc78, 0x013f0001},
200 	{0xc78, 0xfc400001}, {0xc78, 0xfb410001},
201 	{0xc78, 0xfa420001}, {0xc78, 0xf9430001},
202 	{0xc78, 0xf8440001}, {0xc78, 0xf7450001},
203 	{0xc78, 0xf6460001}, {0xc78, 0xf5470001},
204 	{0xc78, 0xf4480001}, {0xc78, 0xf3490001},
205 	{0xc78, 0xf24a0001}, {0xc78, 0xf14b0001},
206 	{0xc78, 0xf04c0001}, {0xc78, 0xef4d0001},
207 	{0xc78, 0xee4e0001}, {0xc78, 0xed4f0001},
208 	{0xc78, 0xec500001}, {0xc78, 0xeb510001},
209 	{0xc78, 0xea520001}, {0xc78, 0xe9530001},
210 	{0xc78, 0xe8540001}, {0xc78, 0xe7550001},
211 	{0xc78, 0xe6560001}, {0xc78, 0xe5570001},
212 	{0xc78, 0xe4580001}, {0xc78, 0xe3590001},
213 	{0xc78, 0xa65a0001}, {0xc78, 0xa55b0001},
214 	{0xc78, 0xa45c0001}, {0xc78, 0xa35d0001},
215 	{0xc78, 0x675e0001}, {0xc78, 0x665f0001},
216 	{0xc78, 0x65600001}, {0xc78, 0x64610001},
217 	{0xc78, 0x63620001}, {0xc78, 0x62630001},
218 	{0xc78, 0x61640001}, {0xc78, 0x48650001},
219 	{0xc78, 0x47660001}, {0xc78, 0x46670001},
220 	{0xc78, 0x45680001}, {0xc78, 0x44690001},
221 	{0xc78, 0x436a0001}, {0xc78, 0x426b0001},
222 	{0xc78, 0x286c0001}, {0xc78, 0x276d0001},
223 	{0xc78, 0x266e0001}, {0xc78, 0x256f0001},
224 	{0xc78, 0x24700001}, {0xc78, 0x09710001},
225 	{0xc78, 0x08720001}, {0xc78, 0x07730001},
226 	{0xc78, 0x06740001}, {0xc78, 0x05750001},
227 	{0xc78, 0x04760001}, {0xc78, 0x03770001},
228 	{0xc78, 0x02780001}, {0xc78, 0x01790001},
229 	{0xc78, 0x017a0001}, {0xc78, 0x017b0001},
230 	{0xc78, 0x017c0001}, {0xc78, 0x017d0001},
231 	{0xc78, 0x017e0001}, {0xc78, 0x017f0001},
232 	{0xc50, 0x69553422},
233 	{0xc50, 0x69553420},
234 	{0x824, 0x00390204},
235 	{0xffff, 0xffffffff}
236 };
237 
238 static struct rtl8xxxu_rfregval rtl8723bu_radioa_1t_init_table[] = {
239 	{0x00, 0x00010000}, {0xb0, 0x000dffe0},
240 	{0xfe, 0x00000000}, {0xfe, 0x00000000},
241 	{0xfe, 0x00000000}, {0xb1, 0x00000018},
242 	{0xfe, 0x00000000}, {0xfe, 0x00000000},
243 	{0xfe, 0x00000000}, {0xb2, 0x00084c00},
244 	{0xb5, 0x0000d2cc}, {0xb6, 0x000925aa},
245 	{0xb7, 0x00000010}, {0xb8, 0x0000907f},
246 	{0x5c, 0x00000002}, {0x7c, 0x00000002},
247 	{0x7e, 0x00000005}, {0x8b, 0x0006fc00},
248 	{0xb0, 0x000ff9f0}, {0x1c, 0x000739d2},
249 	{0x1e, 0x00000000}, {0xdf, 0x00000780},
250 	{0x50, 0x00067435},
251 	/*
252 	 * The 8723bu vendor driver indicates that bit 8 should be set in
253 	 * 0x51 for package types TFBGA90, TFBGA80, and TFBGA79. However
254 	 * they never actually check the package type - and just default
255 	 * to not setting it.
256 	 */
257 	{0x51, 0x0006b04e},
258 	{0x52, 0x000007d2}, {0x53, 0x00000000},
259 	{0x54, 0x00050400}, {0x55, 0x0004026e},
260 	{0xdd, 0x0000004c}, {0x70, 0x00067435},
261 	/*
262 	 * 0x71 has same package type condition as for register 0x51
263 	 */
264 	{0x71, 0x0006b04e},
265 	{0x72, 0x000007d2}, {0x73, 0x00000000},
266 	{0x74, 0x00050400}, {0x75, 0x0004026e},
267 	{0xef, 0x00000100}, {0x34, 0x0000add7},
268 	{0x35, 0x00005c00}, {0x34, 0x00009dd4},
269 	{0x35, 0x00005000}, {0x34, 0x00008dd1},
270 	{0x35, 0x00004400}, {0x34, 0x00007dce},
271 	{0x35, 0x00003800}, {0x34, 0x00006cd1},
272 	{0x35, 0x00004400}, {0x34, 0x00005cce},
273 	{0x35, 0x00003800}, {0x34, 0x000048ce},
274 	{0x35, 0x00004400}, {0x34, 0x000034ce},
275 	{0x35, 0x00003800}, {0x34, 0x00002451},
276 	{0x35, 0x00004400}, {0x34, 0x0000144e},
277 	{0x35, 0x00003800}, {0x34, 0x00000051},
278 	{0x35, 0x00004400}, {0xef, 0x00000000},
279 	{0xef, 0x00000100}, {0xed, 0x00000010},
280 	{0x44, 0x0000add7}, {0x44, 0x00009dd4},
281 	{0x44, 0x00008dd1}, {0x44, 0x00007dce},
282 	{0x44, 0x00006cc1}, {0x44, 0x00005cce},
283 	{0x44, 0x000044d1}, {0x44, 0x000034ce},
284 	{0x44, 0x00002451}, {0x44, 0x0000144e},
285 	{0x44, 0x00000051}, {0xef, 0x00000000},
286 	{0xed, 0x00000000}, {0x7f, 0x00020080},
287 	{0xef, 0x00002000}, {0x3b, 0x000380ef},
288 	{0x3b, 0x000302fe}, {0x3b, 0x00028ce6},
289 	{0x3b, 0x000200bc}, {0x3b, 0x000188a5},
290 	{0x3b, 0x00010fbc}, {0x3b, 0x00008f71},
291 	{0x3b, 0x00000900}, {0xef, 0x00000000},
292 	{0xed, 0x00000001}, {0x40, 0x000380ef},
293 	{0x40, 0x000302fe}, {0x40, 0x00028ce6},
294 	{0x40, 0x000200bc}, {0x40, 0x000188a5},
295 	{0x40, 0x00010fbc}, {0x40, 0x00008f71},
296 	{0x40, 0x00000900}, {0xed, 0x00000000},
297 	{0x82, 0x00080000}, {0x83, 0x00008000},
298 	{0x84, 0x00048d80}, {0x85, 0x00068000},
299 	{0xa2, 0x00080000}, {0xa3, 0x00008000},
300 	{0xa4, 0x00048d80}, {0xa5, 0x00068000},
301 	{0xed, 0x00000002}, {0xef, 0x00000002},
302 	{0x56, 0x00000032}, {0x76, 0x00000032},
303 	{0x01, 0x00000780},
304 	{0xff, 0xffffffff}
305 };
306 
307 static void rtl8723bu_write_btreg(struct rtl8xxxu_priv *priv, u8 reg, u8 data)
308 {
309 	struct h2c_cmd h2c;
310 	int reqnum = 0;
311 
312 	memset(&h2c, 0, sizeof(struct h2c_cmd));
313 	h2c.bt_mp_oper.cmd = H2C_8723B_BT_MP_OPER;
314 	h2c.bt_mp_oper.operreq = 0 | (reqnum << 4);
315 	h2c.bt_mp_oper.opcode = BT_MP_OP_WRITE_REG_VALUE;
316 	h2c.bt_mp_oper.data = data;
317 	rtl8xxxu_gen2_h2c_cmd(priv, &h2c, sizeof(h2c.bt_mp_oper));
318 
319 	reqnum++;
320 	memset(&h2c, 0, sizeof(struct h2c_cmd));
321 	h2c.bt_mp_oper.cmd = H2C_8723B_BT_MP_OPER;
322 	h2c.bt_mp_oper.operreq = 0 | (reqnum << 4);
323 	h2c.bt_mp_oper.opcode = BT_MP_OP_WRITE_REG_VALUE;
324 	h2c.bt_mp_oper.addr = reg;
325 	rtl8xxxu_gen2_h2c_cmd(priv, &h2c, sizeof(h2c.bt_mp_oper));
326 }
327 
328 static void rtl8723bu_reset_8051(struct rtl8xxxu_priv *priv)
329 {
330 	u8 val8;
331 	u16 sys_func;
332 
333 	val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL);
334 	val8 &= ~BIT(1);
335 	rtl8xxxu_write8(priv, REG_RSV_CTRL, val8);
336 
337 	val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL + 1);
338 	val8 &= ~BIT(0);
339 	rtl8xxxu_write8(priv, REG_RSV_CTRL + 1, val8);
340 
341 	sys_func = rtl8xxxu_read16(priv, REG_SYS_FUNC);
342 	sys_func &= ~SYS_FUNC_CPU_ENABLE;
343 	rtl8xxxu_write16(priv, REG_SYS_FUNC, sys_func);
344 
345 	val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL);
346 	val8 &= ~BIT(1);
347 	rtl8xxxu_write8(priv, REG_RSV_CTRL, val8);
348 
349 	val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL + 1);
350 	val8 |= BIT(0);
351 	rtl8xxxu_write8(priv, REG_RSV_CTRL + 1, val8);
352 
353 	sys_func |= SYS_FUNC_CPU_ENABLE;
354 	rtl8xxxu_write16(priv, REG_SYS_FUNC, sys_func);
355 }
356 
357 static void
358 rtl8723b_set_tx_power(struct rtl8xxxu_priv *priv, int channel, bool ht40)
359 {
360 	u32 val32, ofdm, mcs;
361 	u8 cck, ofdmbase, mcsbase;
362 	int group, tx_idx;
363 
364 	tx_idx = 0;
365 	group = rtl8xxxu_gen2_channel_to_group(channel);
366 
367 	cck = priv->cck_tx_power_index_B[group];
368 	val32 = rtl8xxxu_read32(priv, REG_TX_AGC_A_CCK1_MCS32);
369 	val32 &= 0xffff00ff;
370 	val32 |= (cck << 8);
371 	rtl8xxxu_write32(priv, REG_TX_AGC_A_CCK1_MCS32, val32);
372 
373 	val32 = rtl8xxxu_read32(priv, REG_TX_AGC_B_CCK11_A_CCK2_11);
374 	val32 &= 0xff;
375 	val32 |= ((cck << 8) | (cck << 16) | (cck << 24));
376 	rtl8xxxu_write32(priv, REG_TX_AGC_B_CCK11_A_CCK2_11, val32);
377 
378 	ofdmbase = priv->ht40_1s_tx_power_index_B[group];
379 	ofdmbase += priv->ofdm_tx_power_diff[tx_idx].b;
380 	ofdm = ofdmbase | ofdmbase << 8 | ofdmbase << 16 | ofdmbase << 24;
381 
382 	rtl8xxxu_write32(priv, REG_TX_AGC_A_RATE18_06, ofdm);
383 	rtl8xxxu_write32(priv, REG_TX_AGC_A_RATE54_24, ofdm);
384 
385 	mcsbase = priv->ht40_1s_tx_power_index_B[group];
386 	if (ht40)
387 		mcsbase += priv->ht40_tx_power_diff[tx_idx++].b;
388 	else
389 		mcsbase += priv->ht20_tx_power_diff[tx_idx++].b;
390 	mcs = mcsbase | mcsbase << 8 | mcsbase << 16 | mcsbase << 24;
391 
392 	rtl8xxxu_write32(priv, REG_TX_AGC_A_MCS03_MCS00, mcs);
393 	rtl8xxxu_write32(priv, REG_TX_AGC_A_MCS07_MCS04, mcs);
394 }
395 
396 static int rtl8723bu_parse_efuse(struct rtl8xxxu_priv *priv)
397 {
398 	struct rtl8723bu_efuse *efuse = &priv->efuse_wifi.efuse8723bu;
399 	int i;
400 
401 	if (efuse->rtl_id != cpu_to_le16(0x8129))
402 		return -EINVAL;
403 
404 	ether_addr_copy(priv->mac_addr, efuse->mac_addr);
405 
406 	memcpy(priv->cck_tx_power_index_A, efuse->tx_power_index_A.cck_base,
407 	       sizeof(efuse->tx_power_index_A.cck_base));
408 	memcpy(priv->cck_tx_power_index_B, efuse->tx_power_index_B.cck_base,
409 	       sizeof(efuse->tx_power_index_B.cck_base));
410 
411 	memcpy(priv->ht40_1s_tx_power_index_A,
412 	       efuse->tx_power_index_A.ht40_base,
413 	       sizeof(efuse->tx_power_index_A.ht40_base));
414 	memcpy(priv->ht40_1s_tx_power_index_B,
415 	       efuse->tx_power_index_B.ht40_base,
416 	       sizeof(efuse->tx_power_index_B.ht40_base));
417 
418 	priv->ofdm_tx_power_diff[0].a =
419 		efuse->tx_power_index_A.ht20_ofdm_1s_diff.a;
420 	priv->ofdm_tx_power_diff[0].b =
421 		efuse->tx_power_index_B.ht20_ofdm_1s_diff.a;
422 
423 	priv->ht20_tx_power_diff[0].a =
424 		efuse->tx_power_index_A.ht20_ofdm_1s_diff.b;
425 	priv->ht20_tx_power_diff[0].b =
426 		efuse->tx_power_index_B.ht20_ofdm_1s_diff.b;
427 
428 	priv->ht40_tx_power_diff[0].a = 0;
429 	priv->ht40_tx_power_diff[0].b = 0;
430 
431 	for (i = 1; i < RTL8723B_TX_COUNT; i++) {
432 		priv->ofdm_tx_power_diff[i].a =
433 			efuse->tx_power_index_A.pwr_diff[i - 1].ofdm;
434 		priv->ofdm_tx_power_diff[i].b =
435 			efuse->tx_power_index_B.pwr_diff[i - 1].ofdm;
436 
437 		priv->ht20_tx_power_diff[i].a =
438 			efuse->tx_power_index_A.pwr_diff[i - 1].ht20;
439 		priv->ht20_tx_power_diff[i].b =
440 			efuse->tx_power_index_B.pwr_diff[i - 1].ht20;
441 
442 		priv->ht40_tx_power_diff[i].a =
443 			efuse->tx_power_index_A.pwr_diff[i - 1].ht40;
444 		priv->ht40_tx_power_diff[i].b =
445 			efuse->tx_power_index_B.pwr_diff[i - 1].ht40;
446 	}
447 
448 	priv->has_xtalk = 1;
449 	priv->xtalk = priv->efuse_wifi.efuse8723bu.xtal_k & 0x3f;
450 
451 	dev_info(&priv->udev->dev, "Vendor: %.7s\n", efuse->vendor_name);
452 	dev_info(&priv->udev->dev, "Product: %.41s\n", efuse->device_name);
453 
454 	if (rtl8xxxu_debug & RTL8XXXU_DEBUG_EFUSE) {
455 		int i;
456 		unsigned char *raw = priv->efuse_wifi.raw;
457 
458 		dev_info(&priv->udev->dev,
459 			 "%s: dumping efuse (0x%02zx bytes):\n",
460 			 __func__, sizeof(struct rtl8723bu_efuse));
461 		for (i = 0; i < sizeof(struct rtl8723bu_efuse); i += 8)
462 			dev_info(&priv->udev->dev, "%02x: %8ph\n", i, &raw[i]);
463 	}
464 
465 	return 0;
466 }
467 
468 static int rtl8723bu_load_firmware(struct rtl8xxxu_priv *priv)
469 {
470 	char *fw_name;
471 	int ret;
472 
473 	if (priv->enable_bluetooth)
474 		fw_name = "rtlwifi/rtl8723bu_bt.bin";
475 	else
476 		fw_name = "rtlwifi/rtl8723bu_nic.bin";
477 
478 	ret = rtl8xxxu_load_firmware(priv, fw_name);
479 	return ret;
480 }
481 
482 static void rtl8723bu_init_phy_bb(struct rtl8xxxu_priv *priv)
483 {
484 	u8 val8;
485 	u16 val16;
486 
487 	val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC);
488 	val16 |= SYS_FUNC_BB_GLB_RSTN | SYS_FUNC_BBRSTB | SYS_FUNC_DIO_RF;
489 	rtl8xxxu_write16(priv, REG_SYS_FUNC, val16);
490 
491 	rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00);
492 
493 	/* 6. 0x1f[7:0] = 0x07 */
494 	val8 = RF_ENABLE | RF_RSTB | RF_SDMRSTB;
495 	rtl8xxxu_write8(priv, REG_RF_CTRL, val8);
496 
497 	/* Why? */
498 	rtl8xxxu_write8(priv, REG_SYS_FUNC, 0xe3);
499 	rtl8xxxu_write8(priv, REG_AFE_XTAL_CTRL + 1, 0x80);
500 	rtl8xxxu_init_phy_regs(priv, rtl8723b_phy_1t_init_table);
501 
502 	rtl8xxxu_init_phy_regs(priv, rtl8xxx_agc_8723bu_table);
503 }
504 
505 static int rtl8723bu_init_phy_rf(struct rtl8xxxu_priv *priv)
506 {
507 	int ret;
508 
509 	ret = rtl8xxxu_init_phy_rf(priv, rtl8723bu_radioa_1t_init_table, RF_A);
510 	/*
511 	 * PHY LCK
512 	 */
513 	rtl8xxxu_write_rfreg(priv, RF_A, 0xb0, 0xdfbe0);
514 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_MODE_AG, 0x8c01);
515 	msleep(200);
516 	rtl8xxxu_write_rfreg(priv, RF_A, 0xb0, 0xdffe0);
517 
518 	return ret;
519 }
520 
521 static void rtl8723bu_phy_init_antenna_selection(struct rtl8xxxu_priv *priv)
522 {
523 	u32 val32;
524 
525 	val32 = rtl8xxxu_read32(priv, REG_PAD_CTRL1);
526 	val32 &= ~(BIT(20) | BIT(24));
527 	rtl8xxxu_write32(priv, REG_PAD_CTRL1, val32);
528 
529 	val32 = rtl8xxxu_read32(priv, REG_GPIO_MUXCFG);
530 	val32 &= ~BIT(4);
531 	rtl8xxxu_write32(priv, REG_GPIO_MUXCFG, val32);
532 
533 	val32 = rtl8xxxu_read32(priv, REG_GPIO_MUXCFG);
534 	val32 |= BIT(3);
535 	rtl8xxxu_write32(priv, REG_GPIO_MUXCFG, val32);
536 
537 	val32 = rtl8xxxu_read32(priv, REG_LEDCFG0);
538 	val32 |= BIT(24);
539 	rtl8xxxu_write32(priv, REG_LEDCFG0, val32);
540 
541 	val32 = rtl8xxxu_read32(priv, REG_LEDCFG0);
542 	val32 &= ~BIT(23);
543 	rtl8xxxu_write32(priv, REG_LEDCFG0, val32);
544 
545 	val32 = rtl8xxxu_read32(priv, REG_RFE_BUFFER);
546 	val32 |= (BIT(0) | BIT(1));
547 	rtl8xxxu_write32(priv, REG_RFE_BUFFER, val32);
548 
549 	val32 = rtl8xxxu_read32(priv, REG_RFE_CTRL_ANTA_SRC);
550 	val32 &= 0xffffff00;
551 	val32 |= 0x77;
552 	rtl8xxxu_write32(priv, REG_RFE_CTRL_ANTA_SRC, val32);
553 
554 	val32 = rtl8xxxu_read32(priv, REG_PWR_DATA);
555 	val32 |= PWR_DATA_EEPRPAD_RFE_CTRL_EN;
556 	rtl8xxxu_write32(priv, REG_PWR_DATA, val32);
557 }
558 
559 static int rtl8723bu_iqk_path_a(struct rtl8xxxu_priv *priv)
560 {
561 	u32 reg_eac, reg_e94, reg_e9c, path_sel, val32;
562 	int result = 0;
563 
564 	path_sel = rtl8xxxu_read32(priv, REG_S0S1_PATH_SWITCH);
565 
566 	/*
567 	 * Leave IQK mode
568 	 */
569 	val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
570 	val32 &= 0x000000ff;
571 	rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
572 
573 	/*
574 	 * Enable path A PA in TX IQK mode
575 	 */
576 	val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT);
577 	val32 |= 0x80000;
578 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32);
579 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x20000);
580 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0003f);
581 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xc7f87);
582 
583 	/*
584 	 * Tx IQK setting
585 	 */
586 	rtl8xxxu_write32(priv, REG_TX_IQK, 0x01007c00);
587 	rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800);
588 
589 	/* path-A IQK setting */
590 	rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x18008c1c);
591 	rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x38008c1c);
592 	rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c);
593 	rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c);
594 
595 	rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x821403ea);
596 	rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x28110000);
597 	rtl8xxxu_write32(priv, REG_TX_IQK_PI_B, 0x82110000);
598 	rtl8xxxu_write32(priv, REG_RX_IQK_PI_B, 0x28110000);
599 
600 	/* LO calibration setting */
601 	rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x00462911);
602 
603 	/*
604 	 * Enter IQK mode
605 	 */
606 	val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
607 	val32 &= 0x000000ff;
608 	val32 |= 0x80800000;
609 	rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
610 
611 	/*
612 	 * The vendor driver indicates the USB module is always using
613 	 * S0S1 path 1 for the 8723bu. This may be different for 8192eu
614 	 */
615 	if (priv->rf_paths > 1)
616 		rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000000);
617 	else
618 		rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000280);
619 
620 	/*
621 	 * Bit 12 seems to be BT_GRANT, and is only found in the 8723bu.
622 	 * No trace of this in the 8192eu or 8188eu vendor drivers.
623 	 */
624 	rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00000800);
625 
626 	/* One shot, path A LOK & IQK */
627 	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000);
628 	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
629 
630 	mdelay(1);
631 
632 	/* Restore Ant Path */
633 	rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, path_sel);
634 #ifdef RTL8723BU_BT
635 	/* GNT_BT = 1 */
636 	rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00001800);
637 #endif
638 
639 	/*
640 	 * Leave IQK mode
641 	 */
642 	val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
643 	val32 &= 0x000000ff;
644 	rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
645 
646 	/* Check failed */
647 	reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
648 	reg_e94 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_A);
649 	reg_e9c = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_A);
650 
651 	val32 = (reg_e9c >> 16) & 0x3ff;
652 	if (val32 & 0x200)
653 		val32 = 0x400 - val32;
654 
655 	if (!(reg_eac & BIT(28)) &&
656 	    ((reg_e94 & 0x03ff0000) != 0x01420000) &&
657 	    ((reg_e9c & 0x03ff0000) != 0x00420000) &&
658 	    ((reg_e94 & 0x03ff0000)  < 0x01100000) &&
659 	    ((reg_e94 & 0x03ff0000)  > 0x00f00000) &&
660 	    val32 < 0xf)
661 		result |= 0x01;
662 	else	/* If TX not OK, ignore RX */
663 		goto out;
664 
665 out:
666 	return result;
667 }
668 
669 static int rtl8723bu_rx_iqk_path_a(struct rtl8xxxu_priv *priv)
670 {
671 	u32 reg_ea4, reg_eac, reg_e94, reg_e9c, path_sel, val32;
672 	int result = 0;
673 
674 	path_sel = rtl8xxxu_read32(priv, REG_S0S1_PATH_SWITCH);
675 
676 	/*
677 	 * Leave IQK mode
678 	 */
679 	val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
680 	val32 &= 0x000000ff;
681 	rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
682 
683 	/*
684 	 * Enable path A PA in TX IQK mode
685 	 */
686 	val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT);
687 	val32 |= 0x80000;
688 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32);
689 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000);
690 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f);
691 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf7fb7);
692 
693 	/*
694 	 * Tx IQK setting
695 	 */
696 	rtl8xxxu_write32(priv, REG_TX_IQK, 0x01007c00);
697 	rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800);
698 
699 	/* path-A IQK setting */
700 	rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x18008c1c);
701 	rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x38008c1c);
702 	rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c);
703 	rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c);
704 
705 	rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x82160ff0);
706 	rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x28110000);
707 	rtl8xxxu_write32(priv, REG_TX_IQK_PI_B, 0x82110000);
708 	rtl8xxxu_write32(priv, REG_RX_IQK_PI_B, 0x28110000);
709 
710 	/* LO calibration setting */
711 	rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x0046a911);
712 
713 	/*
714 	 * Enter IQK mode
715 	 */
716 	val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
717 	val32 &= 0x000000ff;
718 	val32 |= 0x80800000;
719 	rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
720 
721 	/*
722 	 * The vendor driver indicates the USB module is always using
723 	 * S0S1 path 1 for the 8723bu. This may be different for 8192eu
724 	 */
725 	if (priv->rf_paths > 1)
726 		rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000000);
727 	else
728 		rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000280);
729 
730 	/*
731 	 * Bit 12 seems to be BT_GRANT, and is only found in the 8723bu.
732 	 * No trace of this in the 8192eu or 8188eu vendor drivers.
733 	 */
734 	rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00000800);
735 
736 	/* One shot, path A LOK & IQK */
737 	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000);
738 	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
739 
740 	mdelay(1);
741 
742 	/* Restore Ant Path */
743 	rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, path_sel);
744 #ifdef RTL8723BU_BT
745 	/* GNT_BT = 1 */
746 	rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00001800);
747 #endif
748 
749 	/*
750 	 * Leave IQK mode
751 	 */
752 	val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
753 	val32 &= 0x000000ff;
754 	rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
755 
756 	/* Check failed */
757 	reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
758 	reg_e94 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_A);
759 	reg_e9c = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_A);
760 
761 	val32 = (reg_e9c >> 16) & 0x3ff;
762 	if (val32 & 0x200)
763 		val32 = 0x400 - val32;
764 
765 	if (!(reg_eac & BIT(28)) &&
766 	    ((reg_e94 & 0x03ff0000) != 0x01420000) &&
767 	    ((reg_e9c & 0x03ff0000) != 0x00420000) &&
768 	    ((reg_e94 & 0x03ff0000)  < 0x01100000) &&
769 	    ((reg_e94 & 0x03ff0000)  > 0x00f00000) &&
770 	    val32 < 0xf)
771 		result |= 0x01;
772 	else	/* If TX not OK, ignore RX */
773 		goto out;
774 
775 	val32 = 0x80007c00 | (reg_e94 &0x3ff0000) |
776 		((reg_e9c & 0x3ff0000) >> 16);
777 	rtl8xxxu_write32(priv, REG_TX_IQK, val32);
778 
779 	/*
780 	 * Modify RX IQK mode
781 	 */
782 	val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
783 	val32 &= 0x000000ff;
784 	rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
785 	val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT);
786 	val32 |= 0x80000;
787 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32);
788 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000);
789 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f);
790 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf7d77);
791 
792 	/*
793 	 * PA, PAD setting
794 	 */
795 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_DF, 0xf80);
796 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_55, 0x4021f);
797 
798 	/*
799 	 * RX IQK setting
800 	 */
801 	rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800);
802 
803 	/* path-A IQK setting */
804 	rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x38008c1c);
805 	rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x18008c1c);
806 	rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c);
807 	rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c);
808 
809 	rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x82110000);
810 	rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x2816001f);
811 	rtl8xxxu_write32(priv, REG_TX_IQK_PI_B, 0x82110000);
812 	rtl8xxxu_write32(priv, REG_RX_IQK_PI_B, 0x28110000);
813 
814 	/* LO calibration setting */
815 	rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x0046a8d1);
816 
817 	/*
818 	 * Enter IQK mode
819 	 */
820 	val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
821 	val32 &= 0x000000ff;
822 	val32 |= 0x80800000;
823 	rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
824 
825 	if (priv->rf_paths > 1)
826 		rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000000);
827 	else
828 		rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000280);
829 
830 	/*
831 	 * Disable BT
832 	 */
833 	rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00000800);
834 
835 	/* One shot, path A LOK & IQK */
836 	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000);
837 	rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000);
838 
839 	mdelay(1);
840 
841 	/* Restore Ant Path */
842 	rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, path_sel);
843 #ifdef RTL8723BU_BT
844 	/* GNT_BT = 1 */
845 	rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00001800);
846 #endif
847 
848 	/*
849 	 * Leave IQK mode
850 	 */
851 	val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
852 	val32 &= 0x000000ff;
853 	rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
854 
855 	/* Check failed */
856 	reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
857 	reg_ea4 = rtl8xxxu_read32(priv, REG_RX_POWER_BEFORE_IQK_A_2);
858 
859 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_DF, 0x780);
860 
861 	val32 = (reg_eac >> 16) & 0x3ff;
862 	if (val32 & 0x200)
863 		val32 = 0x400 - val32;
864 
865 	if (!(reg_eac & BIT(27)) &&
866 	    ((reg_ea4 & 0x03ff0000) != 0x01320000) &&
867 	    ((reg_eac & 0x03ff0000) != 0x00360000) &&
868 	    ((reg_ea4 & 0x03ff0000)  < 0x01100000) &&
869 	    ((reg_ea4 & 0x03ff0000)  > 0x00f00000) &&
870 	    val32 < 0xf)
871 		result |= 0x02;
872 	else	/* If TX not OK, ignore RX */
873 		goto out;
874 out:
875 	return result;
876 }
877 
878 static void rtl8723bu_phy_iqcalibrate(struct rtl8xxxu_priv *priv,
879 				      int result[][8], int t)
880 {
881 	struct device *dev = &priv->udev->dev;
882 	u32 i, val32;
883 	int path_a_ok /*, path_b_ok */;
884 	int retry = 2;
885 	static const u32 adda_regs[RTL8XXXU_ADDA_REGS] = {
886 		REG_FPGA0_XCD_SWITCH_CTRL, REG_BLUETOOTH,
887 		REG_RX_WAIT_CCA, REG_TX_CCK_RFON,
888 		REG_TX_CCK_BBON, REG_TX_OFDM_RFON,
889 		REG_TX_OFDM_BBON, REG_TX_TO_RX,
890 		REG_TX_TO_TX, REG_RX_CCK,
891 		REG_RX_OFDM, REG_RX_WAIT_RIFS,
892 		REG_RX_TO_RX, REG_STANDBY,
893 		REG_SLEEP, REG_PMPD_ANAEN
894 	};
895 	static const u32 iqk_mac_regs[RTL8XXXU_MAC_REGS] = {
896 		REG_TXPAUSE, REG_BEACON_CTRL,
897 		REG_BEACON_CTRL_1, REG_GPIO_MUXCFG
898 	};
899 	static const u32 iqk_bb_regs[RTL8XXXU_BB_REGS] = {
900 		REG_OFDM0_TRX_PATH_ENABLE, REG_OFDM0_TR_MUX_PAR,
901 		REG_FPGA0_XCD_RF_SW_CTRL, REG_CONFIG_ANT_A, REG_CONFIG_ANT_B,
902 		REG_FPGA0_XAB_RF_SW_CTRL, REG_FPGA0_XA_RF_INT_OE,
903 		REG_FPGA0_XB_RF_INT_OE, REG_FPGA0_RF_MODE
904 	};
905 	u8 xa_agc = rtl8xxxu_read32(priv, REG_OFDM0_XA_AGC_CORE1) & 0xff;
906 	u8 xb_agc = rtl8xxxu_read32(priv, REG_OFDM0_XB_AGC_CORE1) & 0xff;
907 
908 	/*
909 	 * Note: IQ calibration must be performed after loading
910 	 *       PHY_REG.txt , and radio_a, radio_b.txt
911 	 */
912 
913 	if (t == 0) {
914 		/* Save ADDA parameters, turn Path A ADDA on */
915 		rtl8xxxu_save_regs(priv, adda_regs, priv->adda_backup,
916 				   RTL8XXXU_ADDA_REGS);
917 		rtl8xxxu_save_mac_regs(priv, iqk_mac_regs, priv->mac_backup);
918 		rtl8xxxu_save_regs(priv, iqk_bb_regs,
919 				   priv->bb_backup, RTL8XXXU_BB_REGS);
920 	}
921 
922 	rtl8xxxu_path_adda_on(priv, adda_regs, true);
923 
924 	/* MAC settings */
925 	rtl8xxxu_mac_calibration(priv, iqk_mac_regs, priv->mac_backup);
926 
927 	val32 = rtl8xxxu_read32(priv, REG_CCK0_AFE_SETTING);
928 	val32 |= 0x0f000000;
929 	rtl8xxxu_write32(priv, REG_CCK0_AFE_SETTING, val32);
930 
931 	rtl8xxxu_write32(priv, REG_OFDM0_TRX_PATH_ENABLE, 0x03a05600);
932 	rtl8xxxu_write32(priv, REG_OFDM0_TR_MUX_PAR, 0x000800e4);
933 	rtl8xxxu_write32(priv, REG_FPGA0_XCD_RF_SW_CTRL, 0x22204000);
934 
935 	/*
936 	 * RX IQ calibration setting for 8723B D cut large current issue
937 	 * when leaving IPS
938 	 */
939 	val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
940 	val32 &= 0x000000ff;
941 	rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
942 
943 	val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT);
944 	val32 |= 0x80000;
945 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32);
946 
947 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000);
948 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f);
949 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf7fb7);
950 
951 	val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED);
952 	val32 |= 0x20;
953 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED, val32);
954 
955 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_43, 0x60fbd);
956 
957 	for (i = 0; i < retry; i++) {
958 		path_a_ok = rtl8723bu_iqk_path_a(priv);
959 		if (path_a_ok == 0x01) {
960 			val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
961 			val32 &= 0x000000ff;
962 			rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
963 
964 			val32 = rtl8xxxu_read32(priv,
965 						REG_TX_POWER_BEFORE_IQK_A);
966 			result[t][0] = (val32 >> 16) & 0x3ff;
967 			val32 = rtl8xxxu_read32(priv,
968 						REG_TX_POWER_AFTER_IQK_A);
969 			result[t][1] = (val32 >> 16) & 0x3ff;
970 
971 			break;
972 		}
973 	}
974 
975 	if (!path_a_ok)
976 		dev_dbg(dev, "%s: Path A TX IQK failed!\n", __func__);
977 
978 	for (i = 0; i < retry; i++) {
979 		path_a_ok = rtl8723bu_rx_iqk_path_a(priv);
980 		if (path_a_ok == 0x03) {
981 			val32 = rtl8xxxu_read32(priv,
982 						REG_RX_POWER_BEFORE_IQK_A_2);
983 			result[t][2] = (val32 >> 16) & 0x3ff;
984 			val32 = rtl8xxxu_read32(priv,
985 						REG_RX_POWER_AFTER_IQK_A_2);
986 			result[t][3] = (val32 >> 16) & 0x3ff;
987 
988 			break;
989 		}
990 	}
991 
992 	if (!path_a_ok)
993 		dev_dbg(dev, "%s: Path A RX IQK failed!\n", __func__);
994 
995 	if (priv->tx_paths > 1) {
996 #if 1
997 		dev_warn(dev, "%s: Path B not supported\n", __func__);
998 #else
999 
1000 		/*
1001 		 * Path A into standby
1002 		 */
1003 		val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
1004 		val32 &= 0x000000ff;
1005 		rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
1006 		rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_AC, 0x10000);
1007 
1008 		val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
1009 		val32 &= 0x000000ff;
1010 		val32 |= 0x80800000;
1011 		rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
1012 
1013 		/* Turn Path B ADDA on */
1014 		rtl8xxxu_path_adda_on(priv, adda_regs, false);
1015 
1016 		for (i = 0; i < retry; i++) {
1017 			path_b_ok = rtl8xxxu_iqk_path_b(priv);
1018 			if (path_b_ok == 0x03) {
1019 				val32 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_B);
1020 				result[t][4] = (val32 >> 16) & 0x3ff;
1021 				val32 = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_B);
1022 				result[t][5] = (val32 >> 16) & 0x3ff;
1023 				break;
1024 			}
1025 		}
1026 
1027 		if (!path_b_ok)
1028 			dev_dbg(dev, "%s: Path B IQK failed!\n", __func__);
1029 
1030 		for (i = 0; i < retry; i++) {
1031 			path_b_ok = rtl8723bu_rx_iqk_path_b(priv);
1032 			if (path_a_ok == 0x03) {
1033 				val32 = rtl8xxxu_read32(priv,
1034 							REG_RX_POWER_BEFORE_IQK_B_2);
1035 				result[t][6] = (val32 >> 16) & 0x3ff;
1036 				val32 = rtl8xxxu_read32(priv,
1037 							REG_RX_POWER_AFTER_IQK_B_2);
1038 				result[t][7] = (val32 >> 16) & 0x3ff;
1039 				break;
1040 			}
1041 		}
1042 
1043 		if (!path_b_ok)
1044 			dev_dbg(dev, "%s: Path B RX IQK failed!\n", __func__);
1045 #endif
1046 	}
1047 
1048 	/* Back to BB mode, load original value */
1049 	val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
1050 	val32 &= 0x000000ff;
1051 	rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
1052 
1053 	if (t) {
1054 		/* Reload ADDA power saving parameters */
1055 		rtl8xxxu_restore_regs(priv, adda_regs, priv->adda_backup,
1056 				      RTL8XXXU_ADDA_REGS);
1057 
1058 		/* Reload MAC parameters */
1059 		rtl8xxxu_restore_mac_regs(priv, iqk_mac_regs, priv->mac_backup);
1060 
1061 		/* Reload BB parameters */
1062 		rtl8xxxu_restore_regs(priv, iqk_bb_regs,
1063 				      priv->bb_backup, RTL8XXXU_BB_REGS);
1064 
1065 		/* Restore RX initial gain */
1066 		val32 = rtl8xxxu_read32(priv, REG_OFDM0_XA_AGC_CORE1);
1067 		val32 &= 0xffffff00;
1068 		rtl8xxxu_write32(priv, REG_OFDM0_XA_AGC_CORE1, val32 | 0x50);
1069 		rtl8xxxu_write32(priv, REG_OFDM0_XA_AGC_CORE1, val32 | xa_agc);
1070 
1071 		if (priv->tx_paths > 1) {
1072 			val32 = rtl8xxxu_read32(priv, REG_OFDM0_XB_AGC_CORE1);
1073 			val32 &= 0xffffff00;
1074 			rtl8xxxu_write32(priv, REG_OFDM0_XB_AGC_CORE1,
1075 					 val32 | 0x50);
1076 			rtl8xxxu_write32(priv, REG_OFDM0_XB_AGC_CORE1,
1077 					 val32 | xb_agc);
1078 		}
1079 
1080 		/* Load 0xe30 IQC default value */
1081 		rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x01008c00);
1082 		rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x01008c00);
1083 	}
1084 }
1085 
1086 static void rtl8723bu_phy_iq_calibrate(struct rtl8xxxu_priv *priv)
1087 {
1088 	struct device *dev = &priv->udev->dev;
1089 	int result[4][8];	/* last is final result */
1090 	int i, candidate;
1091 	bool path_a_ok, path_b_ok;
1092 	u32 reg_e94, reg_e9c, reg_ea4, reg_eac;
1093 	u32 reg_eb4, reg_ebc, reg_ec4, reg_ecc;
1094 	u32 val32, bt_control;
1095 	s32 reg_tmp = 0;
1096 	bool simu;
1097 
1098 	rtl8xxxu_gen2_prepare_calibrate(priv, 1);
1099 
1100 	memset(result, 0, sizeof(result));
1101 	candidate = -1;
1102 
1103 	path_a_ok = false;
1104 	path_b_ok = false;
1105 
1106 	bt_control = rtl8xxxu_read32(priv, REG_BT_CONTROL_8723BU);
1107 
1108 	for (i = 0; i < 3; i++) {
1109 		rtl8723bu_phy_iqcalibrate(priv, result, i);
1110 
1111 		if (i == 1) {
1112 			simu = rtl8xxxu_gen2_simularity_compare(priv,
1113 								result, 0, 1);
1114 			if (simu) {
1115 				candidate = 0;
1116 				break;
1117 			}
1118 		}
1119 
1120 		if (i == 2) {
1121 			simu = rtl8xxxu_gen2_simularity_compare(priv,
1122 								result, 0, 2);
1123 			if (simu) {
1124 				candidate = 0;
1125 				break;
1126 			}
1127 
1128 			simu = rtl8xxxu_gen2_simularity_compare(priv,
1129 								result, 1, 2);
1130 			if (simu) {
1131 				candidate = 1;
1132 			} else {
1133 				for (i = 0; i < 8; i++)
1134 					reg_tmp += result[3][i];
1135 
1136 				if (reg_tmp)
1137 					candidate = 3;
1138 				else
1139 					candidate = -1;
1140 			}
1141 		}
1142 	}
1143 
1144 	for (i = 0; i < 4; i++) {
1145 		reg_e94 = result[i][0];
1146 		reg_e9c = result[i][1];
1147 		reg_ea4 = result[i][2];
1148 		reg_eac = result[i][3];
1149 		reg_eb4 = result[i][4];
1150 		reg_ebc = result[i][5];
1151 		reg_ec4 = result[i][6];
1152 		reg_ecc = result[i][7];
1153 	}
1154 
1155 	if (candidate >= 0) {
1156 		reg_e94 = result[candidate][0];
1157 		priv->rege94 =  reg_e94;
1158 		reg_e9c = result[candidate][1];
1159 		priv->rege9c = reg_e9c;
1160 		reg_ea4 = result[candidate][2];
1161 		reg_eac = result[candidate][3];
1162 		reg_eb4 = result[candidate][4];
1163 		priv->regeb4 = reg_eb4;
1164 		reg_ebc = result[candidate][5];
1165 		priv->regebc = reg_ebc;
1166 		reg_ec4 = result[candidate][6];
1167 		reg_ecc = result[candidate][7];
1168 		dev_dbg(dev, "%s: candidate is %x\n", __func__, candidate);
1169 		dev_dbg(dev,
1170 			"%s: e94 =%x e9c=%x ea4=%x eac=%x eb4=%x ebc=%x ec4=%x ecc=%x\n",
1171 			__func__, reg_e94, reg_e9c,
1172 			reg_ea4, reg_eac, reg_eb4, reg_ebc, reg_ec4, reg_ecc);
1173 		path_a_ok = true;
1174 		path_b_ok = true;
1175 	} else {
1176 		reg_e94 = reg_eb4 = priv->rege94 = priv->regeb4 = 0x100;
1177 		reg_e9c = reg_ebc = priv->rege9c = priv->regebc = 0x0;
1178 	}
1179 
1180 	if (reg_e94 && candidate >= 0)
1181 		rtl8xxxu_fill_iqk_matrix_a(priv, path_a_ok, result,
1182 					   candidate, (reg_ea4 == 0));
1183 
1184 	if (priv->tx_paths > 1 && reg_eb4)
1185 		rtl8xxxu_fill_iqk_matrix_b(priv, path_b_ok, result,
1186 					   candidate, (reg_ec4 == 0));
1187 
1188 	rtl8xxxu_save_regs(priv, rtl8xxxu_iqk_phy_iq_bb_reg,
1189 			   priv->bb_recovery_backup, RTL8XXXU_BB_REGS);
1190 
1191 	rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, bt_control);
1192 
1193 	val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT);
1194 	val32 |= 0x80000;
1195 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32);
1196 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x18000);
1197 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f);
1198 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xe6177);
1199 	val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED);
1200 	val32 |= 0x20;
1201 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED, val32);
1202 	rtl8xxxu_write_rfreg(priv, RF_A, 0x43, 0x300bd);
1203 
1204 	if (priv->rf_paths > 1)
1205 		dev_dbg(dev, "%s: 8723BU 2T not supported\n", __func__);
1206 
1207 	rtl8xxxu_gen2_prepare_calibrate(priv, 0);
1208 }
1209 
1210 static int rtl8723bu_active_to_emu(struct rtl8xxxu_priv *priv)
1211 {
1212 	u8 val8;
1213 	u16 val16;
1214 	u32 val32;
1215 	int count, ret = 0;
1216 
1217 	/* Turn off RF */
1218 	rtl8xxxu_write8(priv, REG_RF_CTRL, 0);
1219 
1220 	/* Enable rising edge triggering interrupt */
1221 	val16 = rtl8xxxu_read16(priv, REG_GPIO_INTM);
1222 	val16 &= ~GPIO_INTM_EDGE_TRIG_IRQ;
1223 	rtl8xxxu_write16(priv, REG_GPIO_INTM, val16);
1224 
1225 	/* Release WLON reset 0x04[16]= 1*/
1226 	val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
1227 	val32 |= APS_FSMCO_WLON_RESET;
1228 	rtl8xxxu_write32(priv, REG_APS_FSMCO, val32);
1229 
1230 	/* 0x0005[1] = 1 turn off MAC by HW state machine*/
1231 	val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1);
1232 	val8 |= BIT(1);
1233 	rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8);
1234 
1235 	for (count = RTL8XXXU_MAX_REG_POLL; count; count--) {
1236 		val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1);
1237 		if ((val8 & BIT(1)) == 0)
1238 			break;
1239 		udelay(10);
1240 	}
1241 
1242 	if (!count) {
1243 		dev_warn(&priv->udev->dev, "%s: Disabling MAC timed out\n",
1244 			 __func__);
1245 		ret = -EBUSY;
1246 		goto exit;
1247 	}
1248 
1249 	/* Enable BT control XTAL setting */
1250 	val8 = rtl8xxxu_read8(priv, REG_AFE_MISC);
1251 	val8 &= ~AFE_MISC_WL_XTAL_CTRL;
1252 	rtl8xxxu_write8(priv, REG_AFE_MISC, val8);
1253 
1254 	/* 0x0000[5] = 1 analog Ips to digital, 1:isolation */
1255 	val8 = rtl8xxxu_read8(priv, REG_SYS_ISO_CTRL);
1256 	val8 |= SYS_ISO_ANALOG_IPS;
1257 	rtl8xxxu_write8(priv, REG_SYS_ISO_CTRL, val8);
1258 
1259 	/* 0x0020[0] = 0 disable LDOA12 MACRO block*/
1260 	val8 = rtl8xxxu_read8(priv, REG_LDOA15_CTRL);
1261 	val8 &= ~LDOA15_ENABLE;
1262 	rtl8xxxu_write8(priv, REG_LDOA15_CTRL, val8);
1263 
1264 exit:
1265 	return ret;
1266 }
1267 
1268 static int rtl8723b_emu_to_active(struct rtl8xxxu_priv *priv)
1269 {
1270 	u8 val8;
1271 	u32 val32;
1272 	int count, ret = 0;
1273 
1274 	/* 0x20[0] = 1 enable LDOA12 MACRO block for all interface */
1275 	val8 = rtl8xxxu_read8(priv, REG_LDOA15_CTRL);
1276 	val8 |= LDOA15_ENABLE;
1277 	rtl8xxxu_write8(priv, REG_LDOA15_CTRL, val8);
1278 
1279 	/* 0x67[0] = 0 to disable BT_GPS_SEL pins*/
1280 	val8 = rtl8xxxu_read8(priv, 0x0067);
1281 	val8 &= ~BIT(4);
1282 	rtl8xxxu_write8(priv, 0x0067, val8);
1283 
1284 	mdelay(1);
1285 
1286 	/* 0x00[5] = 0 release analog Ips to digital, 1:isolation */
1287 	val8 = rtl8xxxu_read8(priv, REG_SYS_ISO_CTRL);
1288 	val8 &= ~SYS_ISO_ANALOG_IPS;
1289 	rtl8xxxu_write8(priv, REG_SYS_ISO_CTRL, val8);
1290 
1291 	/* Disable SW LPS 0x04[10]= 0 */
1292 	val32 = rtl8xxxu_read8(priv, REG_APS_FSMCO);
1293 	val32 &= ~APS_FSMCO_SW_LPS;
1294 	rtl8xxxu_write32(priv, REG_APS_FSMCO, val32);
1295 
1296 	/* Wait until 0x04[17] = 1 power ready */
1297 	for (count = RTL8XXXU_MAX_REG_POLL; count; count--) {
1298 		val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
1299 		if (val32 & BIT(17))
1300 			break;
1301 
1302 		udelay(10);
1303 	}
1304 
1305 	if (!count) {
1306 		ret = -EBUSY;
1307 		goto exit;
1308 	}
1309 
1310 	/* We should be able to optimize the following three entries into one */
1311 
1312 	/* Release WLON reset 0x04[16]= 1*/
1313 	val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
1314 	val32 |= APS_FSMCO_WLON_RESET;
1315 	rtl8xxxu_write32(priv, REG_APS_FSMCO, val32);
1316 
1317 	/* Disable HWPDN 0x04[15]= 0*/
1318 	val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
1319 	val32 &= ~APS_FSMCO_HW_POWERDOWN;
1320 	rtl8xxxu_write32(priv, REG_APS_FSMCO, val32);
1321 
1322 	/* Disable WL suspend*/
1323 	val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
1324 	val32 &= ~(APS_FSMCO_HW_SUSPEND | APS_FSMCO_PCIE);
1325 	rtl8xxxu_write32(priv, REG_APS_FSMCO, val32);
1326 
1327 	/* Set, then poll until 0 */
1328 	val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
1329 	val32 |= APS_FSMCO_MAC_ENABLE;
1330 	rtl8xxxu_write32(priv, REG_APS_FSMCO, val32);
1331 
1332 	for (count = RTL8XXXU_MAX_REG_POLL; count; count--) {
1333 		val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO);
1334 		if ((val32 & APS_FSMCO_MAC_ENABLE) == 0) {
1335 			ret = 0;
1336 			break;
1337 		}
1338 		udelay(10);
1339 	}
1340 
1341 	if (!count) {
1342 		ret = -EBUSY;
1343 		goto exit;
1344 	}
1345 
1346 	/* Enable WL control XTAL setting */
1347 	val8 = rtl8xxxu_read8(priv, REG_AFE_MISC);
1348 	val8 |= AFE_MISC_WL_XTAL_CTRL;
1349 	rtl8xxxu_write8(priv, REG_AFE_MISC, val8);
1350 
1351 	/* Enable falling edge triggering interrupt */
1352 	val8 = rtl8xxxu_read8(priv, REG_GPIO_INTM + 1);
1353 	val8 |= BIT(1);
1354 	rtl8xxxu_write8(priv, REG_GPIO_INTM + 1, val8);
1355 
1356 	/* Enable GPIO9 interrupt mode */
1357 	val8 = rtl8xxxu_read8(priv, REG_GPIO_IO_SEL_2 + 1);
1358 	val8 |= BIT(1);
1359 	rtl8xxxu_write8(priv, REG_GPIO_IO_SEL_2 + 1, val8);
1360 
1361 	/* Enable GPIO9 input mode */
1362 	val8 = rtl8xxxu_read8(priv, REG_GPIO_IO_SEL_2);
1363 	val8 &= ~BIT(1);
1364 	rtl8xxxu_write8(priv, REG_GPIO_IO_SEL_2, val8);
1365 
1366 	/* Enable HSISR GPIO[C:0] interrupt */
1367 	val8 = rtl8xxxu_read8(priv, REG_HSIMR);
1368 	val8 |= BIT(0);
1369 	rtl8xxxu_write8(priv, REG_HSIMR, val8);
1370 
1371 	/* Enable HSISR GPIO9 interrupt */
1372 	val8 = rtl8xxxu_read8(priv, REG_HSIMR + 2);
1373 	val8 |= BIT(1);
1374 	rtl8xxxu_write8(priv, REG_HSIMR + 2, val8);
1375 
1376 	val8 = rtl8xxxu_read8(priv, REG_MULTI_FUNC_CTRL);
1377 	val8 |= MULTI_WIFI_HW_ROF_EN;
1378 	rtl8xxxu_write8(priv, REG_MULTI_FUNC_CTRL, val8);
1379 
1380 	/* For GPIO9 internal pull high setting BIT(14) */
1381 	val8 = rtl8xxxu_read8(priv, REG_MULTI_FUNC_CTRL + 1);
1382 	val8 |= BIT(6);
1383 	rtl8xxxu_write8(priv, REG_MULTI_FUNC_CTRL + 1, val8);
1384 
1385 exit:
1386 	return ret;
1387 }
1388 
1389 static int rtl8723bu_power_on(struct rtl8xxxu_priv *priv)
1390 {
1391 	u8 val8;
1392 	u16 val16;
1393 	u32 val32;
1394 	int ret;
1395 
1396 	rtl8xxxu_disabled_to_emu(priv);
1397 
1398 	ret = rtl8723b_emu_to_active(priv);
1399 	if (ret)
1400 		goto exit;
1401 
1402 	/*
1403 	 * Enable MAC DMA/WMAC/SCHEDULE/SEC block
1404 	 * Set CR bit10 to enable 32k calibration.
1405 	 */
1406 	val16 = rtl8xxxu_read16(priv, REG_CR);
1407 	val16 |= (CR_HCI_TXDMA_ENABLE | CR_HCI_RXDMA_ENABLE |
1408 		  CR_TXDMA_ENABLE | CR_RXDMA_ENABLE |
1409 		  CR_PROTOCOL_ENABLE | CR_SCHEDULE_ENABLE |
1410 		  CR_MAC_TX_ENABLE | CR_MAC_RX_ENABLE |
1411 		  CR_SECURITY_ENABLE | CR_CALTIMER_ENABLE);
1412 	rtl8xxxu_write16(priv, REG_CR, val16);
1413 
1414 	/*
1415 	 * BT coexist power on settings. This is identical for 1 and 2
1416 	 * antenna parts.
1417 	 */
1418 	rtl8xxxu_write8(priv, REG_PAD_CTRL1 + 3, 0x20);
1419 
1420 	val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC);
1421 	val16 |= SYS_FUNC_BBRSTB | SYS_FUNC_BB_GLB_RSTN;
1422 	rtl8xxxu_write16(priv, REG_SYS_FUNC, val16);
1423 
1424 	rtl8xxxu_write8(priv, REG_BT_CONTROL_8723BU + 1, 0x18);
1425 	rtl8xxxu_write8(priv, REG_WLAN_ACT_CONTROL_8723B, 0x04);
1426 	rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00);
1427 	/* Antenna inverse */
1428 	rtl8xxxu_write8(priv, 0xfe08, 0x01);
1429 
1430 	val16 = rtl8xxxu_read16(priv, REG_PWR_DATA);
1431 	val16 |= PWR_DATA_EEPRPAD_RFE_CTRL_EN;
1432 	rtl8xxxu_write16(priv, REG_PWR_DATA, val16);
1433 
1434 	val32 = rtl8xxxu_read32(priv, REG_LEDCFG0);
1435 	val32 |= LEDCFG0_DPDT_SELECT;
1436 	rtl8xxxu_write32(priv, REG_LEDCFG0, val32);
1437 
1438 	val8 = rtl8xxxu_read8(priv, REG_PAD_CTRL1);
1439 	val8 &= ~PAD_CTRL1_SW_DPDT_SEL_DATA;
1440 	rtl8xxxu_write8(priv, REG_PAD_CTRL1, val8);
1441 exit:
1442 	return ret;
1443 }
1444 
1445 static void rtl8723bu_power_off(struct rtl8xxxu_priv *priv)
1446 {
1447 	u8 val8;
1448 	u16 val16;
1449 
1450 	rtl8xxxu_flush_fifo(priv);
1451 
1452 	/*
1453 	 * Disable TX report timer
1454 	 */
1455 	val8 = rtl8xxxu_read8(priv, REG_TX_REPORT_CTRL);
1456 	val8 &= ~TX_REPORT_CTRL_TIMER_ENABLE;
1457 	rtl8xxxu_write8(priv, REG_TX_REPORT_CTRL, val8);
1458 
1459 	rtl8xxxu_write8(priv, REG_CR, 0x0000);
1460 
1461 	rtl8xxxu_active_to_lps(priv);
1462 
1463 	/* Reset Firmware if running in RAM */
1464 	if (rtl8xxxu_read8(priv, REG_MCU_FW_DL) & MCU_FW_RAM_SEL)
1465 		rtl8xxxu_firmware_self_reset(priv);
1466 
1467 	/* Reset MCU */
1468 	val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC);
1469 	val16 &= ~SYS_FUNC_CPU_ENABLE;
1470 	rtl8xxxu_write16(priv, REG_SYS_FUNC, val16);
1471 
1472 	/* Reset MCU ready status */
1473 	rtl8xxxu_write8(priv, REG_MCU_FW_DL, 0x00);
1474 
1475 	rtl8723bu_active_to_emu(priv);
1476 
1477 	val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1);
1478 	val8 |= BIT(3); /* APS_FSMCO_HW_SUSPEND */
1479 	rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8);
1480 
1481 	/* 0x48[16] = 1 to enable GPIO9 as EXT wakeup */
1482 	val8 = rtl8xxxu_read8(priv, REG_GPIO_INTM + 2);
1483 	val8 |= BIT(0);
1484 	rtl8xxxu_write8(priv, REG_GPIO_INTM + 2, val8);
1485 }
1486 
1487 static void rtl8723b_enable_rf(struct rtl8xxxu_priv *priv)
1488 {
1489 	struct h2c_cmd h2c;
1490 	u32 val32;
1491 	u8 val8;
1492 
1493 	val32 = rtl8xxxu_read32(priv, REG_RX_WAIT_CCA);
1494 	val32 |= (BIT(22) | BIT(23));
1495 	rtl8xxxu_write32(priv, REG_RX_WAIT_CCA, val32);
1496 
1497 	/*
1498 	 * No indication anywhere as to what 0x0790 does. The 2 antenna
1499 	 * vendor code preserves bits 6-7 here.
1500 	 */
1501 	rtl8xxxu_write8(priv, 0x0790, 0x05);
1502 	/*
1503 	 * 0x0778 seems to be related to enabling the number of antennas
1504 	 * In the vendor driver halbtc8723b2ant_InitHwConfig() sets it
1505 	 * to 0x03, while halbtc8723b1ant_InitHwConfig() sets it to 0x01
1506 	 */
1507 	rtl8xxxu_write8(priv, 0x0778, 0x01);
1508 
1509 	val8 = rtl8xxxu_read8(priv, REG_GPIO_MUXCFG);
1510 	val8 |= BIT(5);
1511 	rtl8xxxu_write8(priv, REG_GPIO_MUXCFG, val8);
1512 
1513 	rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_IQADJ_G1, 0x780);
1514 
1515 	rtl8723bu_write_btreg(priv, 0x3c, 0x15); /* BT TRx Mask on */
1516 
1517 	/*
1518 	 * Set BT grant to low
1519 	 */
1520 	memset(&h2c, 0, sizeof(struct h2c_cmd));
1521 	h2c.bt_grant.cmd = H2C_8723B_BT_GRANT;
1522 	h2c.bt_grant.data = 0;
1523 	rtl8xxxu_gen2_h2c_cmd(priv, &h2c, sizeof(h2c.bt_grant));
1524 
1525 	/*
1526 	 * WLAN action by PTA
1527 	 */
1528 	rtl8xxxu_write8(priv, REG_WLAN_ACT_CONTROL_8723B, 0x0c);
1529 
1530 	/*
1531 	 * BT select S0/S1 controlled by WiFi
1532 	 */
1533 	val8 = rtl8xxxu_read8(priv, 0x0067);
1534 	val8 |= BIT(5);
1535 	rtl8xxxu_write8(priv, 0x0067, val8);
1536 
1537 	val32 = rtl8xxxu_read32(priv, REG_PWR_DATA);
1538 	val32 |= PWR_DATA_EEPRPAD_RFE_CTRL_EN;
1539 	rtl8xxxu_write32(priv, REG_PWR_DATA, val32);
1540 
1541 	/*
1542 	 * Bits 6/7 are marked in/out ... but for what?
1543 	 */
1544 	rtl8xxxu_write8(priv, 0x0974, 0xff);
1545 
1546 	val32 = rtl8xxxu_read32(priv, REG_RFE_BUFFER);
1547 	val32 |= (BIT(0) | BIT(1));
1548 	rtl8xxxu_write32(priv, REG_RFE_BUFFER, val32);
1549 
1550 	rtl8xxxu_write8(priv, REG_RFE_CTRL_ANTA_SRC, 0x77);
1551 
1552 	val32 = rtl8xxxu_read32(priv, REG_LEDCFG0);
1553 	val32 &= ~BIT(24);
1554 	val32 |= BIT(23);
1555 	rtl8xxxu_write32(priv, REG_LEDCFG0, val32);
1556 
1557 	/*
1558 	 * Fix external switch Main->S1, Aux->S0
1559 	 */
1560 	val8 = rtl8xxxu_read8(priv, REG_PAD_CTRL1);
1561 	val8 &= ~BIT(0);
1562 	rtl8xxxu_write8(priv, REG_PAD_CTRL1, val8);
1563 
1564 	memset(&h2c, 0, sizeof(struct h2c_cmd));
1565 	h2c.ant_sel_rsv.cmd = H2C_8723B_ANT_SEL_RSV;
1566 	h2c.ant_sel_rsv.ant_inverse = 1;
1567 	h2c.ant_sel_rsv.int_switch_type = 0;
1568 	rtl8xxxu_gen2_h2c_cmd(priv, &h2c, sizeof(h2c.ant_sel_rsv));
1569 
1570 	/*
1571 	 * Different settings per different antenna position.
1572 	 *      Antenna Position:   | Normal   Inverse
1573 	 * --------------------------------------------------
1574 	 * Antenna switch to BT:    |  0x280,   0x00
1575 	 * Antenna switch to WiFi:  |  0x0,     0x280
1576 	 * Antenna switch to PTA:   |  0x200,   0x80
1577 	 */
1578 	rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x80);
1579 
1580 	/*
1581 	 * Software control, antenna at WiFi side
1582 	 */
1583 	rtl8723bu_set_ps_tdma(priv, 0x08, 0x00, 0x00, 0x00, 0x00);
1584 
1585 	rtl8xxxu_write32(priv, REG_BT_COEX_TABLE1, 0x55555555);
1586 	rtl8xxxu_write32(priv, REG_BT_COEX_TABLE2, 0x55555555);
1587 	rtl8xxxu_write32(priv, REG_BT_COEX_TABLE3, 0x00ffffff);
1588 	rtl8xxxu_write8(priv, REG_BT_COEX_TABLE4, 0x03);
1589 
1590 	memset(&h2c, 0, sizeof(struct h2c_cmd));
1591 	h2c.bt_info.cmd = H2C_8723B_BT_INFO;
1592 	h2c.bt_info.data = BIT(0);
1593 	rtl8xxxu_gen2_h2c_cmd(priv, &h2c, sizeof(h2c.bt_info));
1594 
1595 	memset(&h2c, 0, sizeof(struct h2c_cmd));
1596 	h2c.ignore_wlan.cmd = H2C_8723B_BT_IGNORE_WLANACT;
1597 	h2c.ignore_wlan.data = 0;
1598 	rtl8xxxu_gen2_h2c_cmd(priv, &h2c, sizeof(h2c.ignore_wlan));
1599 }
1600 
1601 static void rtl8723bu_init_aggregation(struct rtl8xxxu_priv *priv)
1602 {
1603 	u32 agg_rx;
1604 	u8 agg_ctrl;
1605 
1606 	/*
1607 	 * For now simply disable RX aggregation
1608 	 */
1609 	agg_ctrl = rtl8xxxu_read8(priv, REG_TRXDMA_CTRL);
1610 	agg_ctrl &= ~TRXDMA_CTRL_RXDMA_AGG_EN;
1611 
1612 	agg_rx = rtl8xxxu_read32(priv, REG_RXDMA_AGG_PG_TH);
1613 	agg_rx &= ~RXDMA_USB_AGG_ENABLE;
1614 	agg_rx &= ~0xff0f;
1615 
1616 	rtl8xxxu_write8(priv, REG_TRXDMA_CTRL, agg_ctrl);
1617 	rtl8xxxu_write32(priv, REG_RXDMA_AGG_PG_TH, agg_rx);
1618 }
1619 
1620 static void rtl8723bu_init_statistics(struct rtl8xxxu_priv *priv)
1621 {
1622 	u32 val32;
1623 
1624 	/* Time duration for NHM unit: 4us, 0x2710=40ms */
1625 	rtl8xxxu_write16(priv, REG_NHM_TIMER_8723B + 2, 0x2710);
1626 	rtl8xxxu_write16(priv, REG_NHM_TH9_TH10_8723B + 2, 0xffff);
1627 	rtl8xxxu_write32(priv, REG_NHM_TH3_TO_TH0_8723B, 0xffffff52);
1628 	rtl8xxxu_write32(priv, REG_NHM_TH7_TO_TH4_8723B, 0xffffffff);
1629 	/* TH8 */
1630 	val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
1631 	val32 |= 0xff;
1632 	rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
1633 	/* Enable CCK */
1634 	val32 = rtl8xxxu_read32(priv, REG_NHM_TH9_TH10_8723B);
1635 	val32 |= BIT(8) | BIT(9) | BIT(10);
1636 	rtl8xxxu_write32(priv, REG_NHM_TH9_TH10_8723B, val32);
1637 	/* Max power amongst all RX antennas */
1638 	val32 = rtl8xxxu_read32(priv, REG_OFDM0_FA_RSTC);
1639 	val32 |= BIT(7);
1640 	rtl8xxxu_write32(priv, REG_OFDM0_FA_RSTC, val32);
1641 }
1642 
1643 struct rtl8xxxu_fileops rtl8723bu_fops = {
1644 	.parse_efuse = rtl8723bu_parse_efuse,
1645 	.load_firmware = rtl8723bu_load_firmware,
1646 	.power_on = rtl8723bu_power_on,
1647 	.power_off = rtl8723bu_power_off,
1648 	.reset_8051 = rtl8723bu_reset_8051,
1649 	.llt_init = rtl8xxxu_auto_llt_table,
1650 	.init_phy_bb = rtl8723bu_init_phy_bb,
1651 	.init_phy_rf = rtl8723bu_init_phy_rf,
1652 	.phy_init_antenna_selection = rtl8723bu_phy_init_antenna_selection,
1653 	.phy_iq_calibrate = rtl8723bu_phy_iq_calibrate,
1654 	.config_channel = rtl8xxxu_gen2_config_channel,
1655 	.parse_rx_desc = rtl8xxxu_parse_rxdesc24,
1656 	.init_aggregation = rtl8723bu_init_aggregation,
1657 	.init_statistics = rtl8723bu_init_statistics,
1658 	.enable_rf = rtl8723b_enable_rf,
1659 	.disable_rf = rtl8xxxu_gen2_disable_rf,
1660 	.usb_quirks = rtl8xxxu_gen2_usb_quirks,
1661 	.set_tx_power = rtl8723b_set_tx_power,
1662 	.update_rate_mask = rtl8xxxu_gen2_update_rate_mask,
1663 	.report_connect = rtl8xxxu_gen2_report_connect,
1664 	.fill_txdesc = rtl8xxxu_fill_txdesc_v2,
1665 	.writeN_block_size = 1024,
1666 	.tx_desc_size = sizeof(struct rtl8xxxu_txdesc40),
1667 	.rx_desc_size = sizeof(struct rtl8xxxu_rxdesc24),
1668 	.has_s0s1 = 1,
1669 	.has_tx_report = 1,
1670 	.gen2_thermal_meter = 1,
1671 	.needs_full_init = 1,
1672 	.adda_1t_init = 0x01c00014,
1673 	.adda_1t_path_on = 0x01c00014,
1674 	.adda_2t_path_on_a = 0x01c00014,
1675 	.adda_2t_path_on_b = 0x01c00014,
1676 	.trxff_boundary = 0x3f7f,
1677 	.pbp_rx = PBP_PAGE_SIZE_256,
1678 	.pbp_tx = PBP_PAGE_SIZE_256,
1679 	.mactable = rtl8723b_mac_init_table,
1680 	.total_page_num = TX_TOTAL_PAGE_NUM_8723B,
1681 	.page_num_hi = TX_PAGE_NUM_HI_PQ_8723B,
1682 	.page_num_lo = TX_PAGE_NUM_LO_PQ_8723B,
1683 	.page_num_norm = TX_PAGE_NUM_NORM_PQ_8723B,
1684 };
1685