1 /*
2  * Linux device driver for RTL8187
3  *
4  * Copyright 2007 Michael Wu <flamingice@sourmilk.net>
5  * Copyright 2007 Andrea Merello <andrea.merello@gmail.com>
6  *
7  * Based on the r8187 driver, which is:
8  * Copyright 2005 Andrea Merello <andrea.merello@gmail.com>, et al.
9  *
10  * The driver was extended to the RTL8187B in 2008 by:
11  *	Herton Ronaldo Krzesinski <herton@mandriva.com.br>
12  *	Hin-Tak Leung <htl10@users.sourceforge.net>
13  *	Larry Finger <Larry.Finger@lwfinger.net>
14  *
15  * Magic delays and register offsets below are taken from the original
16  * r8187 driver sources.  Thanks to Realtek for their support!
17  *
18  * This program is free software; you can redistribute it and/or modify
19  * it under the terms of the GNU General Public License version 2 as
20  * published by the Free Software Foundation.
21  */
22 
23 #include <linux/usb.h>
24 #include <linux/slab.h>
25 #include <linux/delay.h>
26 #include <linux/etherdevice.h>
27 #include <linux/eeprom_93cx6.h>
28 #include <linux/module.h>
29 #include <net/mac80211.h>
30 
31 #include "rtl8187.h"
32 #include "rtl8225.h"
33 #ifdef CONFIG_RTL8187_LEDS
34 #include "leds.h"
35 #endif
36 #include "rfkill.h"
37 
38 MODULE_AUTHOR("Michael Wu <flamingice@sourmilk.net>");
39 MODULE_AUTHOR("Andrea Merello <andrea.merello@gmail.com>");
40 MODULE_AUTHOR("Herton Ronaldo Krzesinski <herton@mandriva.com.br>");
41 MODULE_AUTHOR("Hin-Tak Leung <htl10@users.sourceforge.net>");
42 MODULE_AUTHOR("Larry Finger <Larry.Finger@lwfinger.net>");
43 MODULE_DESCRIPTION("RTL8187/RTL8187B USB wireless driver");
44 MODULE_LICENSE("GPL");
45 
46 static struct usb_device_id rtl8187_table[] = {
47 	/* Asus */
48 	{USB_DEVICE(0x0b05, 0x171d), .driver_info = DEVICE_RTL8187},
49 	/* Belkin */
50 	{USB_DEVICE(0x050d, 0x705e), .driver_info = DEVICE_RTL8187B},
51 	/* Realtek */
52 	{USB_DEVICE(0x0bda, 0x8187), .driver_info = DEVICE_RTL8187},
53 	{USB_DEVICE(0x0bda, 0x8189), .driver_info = DEVICE_RTL8187B},
54 	{USB_DEVICE(0x0bda, 0x8197), .driver_info = DEVICE_RTL8187B},
55 	{USB_DEVICE(0x0bda, 0x8198), .driver_info = DEVICE_RTL8187B},
56 	/* Surecom */
57 	{USB_DEVICE(0x0769, 0x11F2), .driver_info = DEVICE_RTL8187},
58 	/* Logitech */
59 	{USB_DEVICE(0x0789, 0x010C), .driver_info = DEVICE_RTL8187},
60 	/* Netgear */
61 	{USB_DEVICE(0x0846, 0x6100), .driver_info = DEVICE_RTL8187},
62 	{USB_DEVICE(0x0846, 0x6a00), .driver_info = DEVICE_RTL8187},
63 	{USB_DEVICE(0x0846, 0x4260), .driver_info = DEVICE_RTL8187B},
64 	/* HP */
65 	{USB_DEVICE(0x03f0, 0xca02), .driver_info = DEVICE_RTL8187},
66 	/* Sitecom */
67 	{USB_DEVICE(0x0df6, 0x000d), .driver_info = DEVICE_RTL8187},
68 	{USB_DEVICE(0x0df6, 0x0028), .driver_info = DEVICE_RTL8187B},
69 	{USB_DEVICE(0x0df6, 0x0029), .driver_info = DEVICE_RTL8187B},
70 	/* Sphairon Access Systems GmbH */
71 	{USB_DEVICE(0x114B, 0x0150), .driver_info = DEVICE_RTL8187},
72 	/* Dick Smith Electronics */
73 	{USB_DEVICE(0x1371, 0x9401), .driver_info = DEVICE_RTL8187},
74 	/* Abocom */
75 	{USB_DEVICE(0x13d1, 0xabe6), .driver_info = DEVICE_RTL8187},
76 	/* Qcom */
77 	{USB_DEVICE(0x18E8, 0x6232), .driver_info = DEVICE_RTL8187},
78 	/* AirLive */
79 	{USB_DEVICE(0x1b75, 0x8187), .driver_info = DEVICE_RTL8187},
80 	/* Linksys */
81 	{USB_DEVICE(0x1737, 0x0073), .driver_info = DEVICE_RTL8187B},
82 	{}
83 };
84 
85 MODULE_DEVICE_TABLE(usb, rtl8187_table);
86 
87 static const struct ieee80211_rate rtl818x_rates[] = {
88 	{ .bitrate = 10, .hw_value = 0, },
89 	{ .bitrate = 20, .hw_value = 1, },
90 	{ .bitrate = 55, .hw_value = 2, },
91 	{ .bitrate = 110, .hw_value = 3, },
92 	{ .bitrate = 60, .hw_value = 4, },
93 	{ .bitrate = 90, .hw_value = 5, },
94 	{ .bitrate = 120, .hw_value = 6, },
95 	{ .bitrate = 180, .hw_value = 7, },
96 	{ .bitrate = 240, .hw_value = 8, },
97 	{ .bitrate = 360, .hw_value = 9, },
98 	{ .bitrate = 480, .hw_value = 10, },
99 	{ .bitrate = 540, .hw_value = 11, },
100 };
101 
102 static const struct ieee80211_channel rtl818x_channels[] = {
103 	{ .center_freq = 2412 },
104 	{ .center_freq = 2417 },
105 	{ .center_freq = 2422 },
106 	{ .center_freq = 2427 },
107 	{ .center_freq = 2432 },
108 	{ .center_freq = 2437 },
109 	{ .center_freq = 2442 },
110 	{ .center_freq = 2447 },
111 	{ .center_freq = 2452 },
112 	{ .center_freq = 2457 },
113 	{ .center_freq = 2462 },
114 	{ .center_freq = 2467 },
115 	{ .center_freq = 2472 },
116 	{ .center_freq = 2484 },
117 };
118 
119 static void rtl8187_iowrite_async_cb(struct urb *urb)
120 {
121 	kfree(urb->context);
122 }
123 
124 static void rtl8187_iowrite_async(struct rtl8187_priv *priv, __le16 addr,
125 				  void *data, u16 len)
126 {
127 	struct usb_ctrlrequest *dr;
128 	struct urb *urb;
129 	struct rtl8187_async_write_data {
130 		u8 data[4];
131 		struct usb_ctrlrequest dr;
132 	} *buf;
133 	int rc;
134 
135 	buf = kmalloc(sizeof(*buf), GFP_ATOMIC);
136 	if (!buf)
137 		return;
138 
139 	urb = usb_alloc_urb(0, GFP_ATOMIC);
140 	if (!urb) {
141 		kfree(buf);
142 		return;
143 	}
144 
145 	dr = &buf->dr;
146 
147 	dr->bRequestType = RTL8187_REQT_WRITE;
148 	dr->bRequest = RTL8187_REQ_SET_REG;
149 	dr->wValue = addr;
150 	dr->wIndex = 0;
151 	dr->wLength = cpu_to_le16(len);
152 
153 	memcpy(buf, data, len);
154 
155 	usb_fill_control_urb(urb, priv->udev, usb_sndctrlpipe(priv->udev, 0),
156 			     (unsigned char *)dr, buf, len,
157 			     rtl8187_iowrite_async_cb, buf);
158 	usb_anchor_urb(urb, &priv->anchored);
159 	rc = usb_submit_urb(urb, GFP_ATOMIC);
160 	if (rc < 0) {
161 		kfree(buf);
162 		usb_unanchor_urb(urb);
163 	}
164 	usb_free_urb(urb);
165 }
166 
167 static inline void rtl818x_iowrite32_async(struct rtl8187_priv *priv,
168 					   __le32 *addr, u32 val)
169 {
170 	__le32 buf = cpu_to_le32(val);
171 
172 	rtl8187_iowrite_async(priv, cpu_to_le16((unsigned long)addr),
173 			      &buf, sizeof(buf));
174 }
175 
176 void rtl8187_write_phy(struct ieee80211_hw *dev, u8 addr, u32 data)
177 {
178 	struct rtl8187_priv *priv = dev->priv;
179 
180 	data <<= 8;
181 	data |= addr | 0x80;
182 
183 	rtl818x_iowrite8(priv, &priv->map->PHY[3], (data >> 24) & 0xFF);
184 	rtl818x_iowrite8(priv, &priv->map->PHY[2], (data >> 16) & 0xFF);
185 	rtl818x_iowrite8(priv, &priv->map->PHY[1], (data >> 8) & 0xFF);
186 	rtl818x_iowrite8(priv, &priv->map->PHY[0], data & 0xFF);
187 }
188 
189 static void rtl8187_tx_cb(struct urb *urb)
190 {
191 	struct sk_buff *skb = (struct sk_buff *)urb->context;
192 	struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
193 	struct ieee80211_hw *hw = info->rate_driver_data[0];
194 	struct rtl8187_priv *priv = hw->priv;
195 
196 	skb_pull(skb, priv->is_rtl8187b ? sizeof(struct rtl8187b_tx_hdr) :
197 					  sizeof(struct rtl8187_tx_hdr));
198 	ieee80211_tx_info_clear_status(info);
199 
200 	if (!(urb->status) && !(info->flags & IEEE80211_TX_CTL_NO_ACK)) {
201 		if (priv->is_rtl8187b) {
202 			skb_queue_tail(&priv->b_tx_status.queue, skb);
203 
204 			/* queue is "full", discard last items */
205 			while (skb_queue_len(&priv->b_tx_status.queue) > 5) {
206 				struct sk_buff *old_skb;
207 
208 				dev_dbg(&priv->udev->dev,
209 					"transmit status queue full\n");
210 
211 				old_skb = skb_dequeue(&priv->b_tx_status.queue);
212 				ieee80211_tx_status_irqsafe(hw, old_skb);
213 			}
214 			return;
215 		} else {
216 			info->flags |= IEEE80211_TX_STAT_ACK;
217 		}
218 	}
219 	if (priv->is_rtl8187b)
220 		ieee80211_tx_status_irqsafe(hw, skb);
221 	else {
222 		/* Retry information for the RTI8187 is only available by
223 		 * reading a register in the device. We are in interrupt mode
224 		 * here, thus queue the skb and finish on a work queue. */
225 		skb_queue_tail(&priv->b_tx_status.queue, skb);
226 		ieee80211_queue_delayed_work(hw, &priv->work, 0);
227 	}
228 }
229 
230 static void rtl8187_tx(struct ieee80211_hw *dev,
231 		       struct ieee80211_tx_control *control,
232 		       struct sk_buff *skb)
233 {
234 	struct rtl8187_priv *priv = dev->priv;
235 	struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
236 	struct ieee80211_hdr *tx_hdr =	(struct ieee80211_hdr *)(skb->data);
237 	unsigned int ep;
238 	void *buf;
239 	struct urb *urb;
240 	__le16 rts_dur = 0;
241 	u32 flags;
242 	int rc;
243 
244 	urb = usb_alloc_urb(0, GFP_ATOMIC);
245 	if (!urb) {
246 		kfree_skb(skb);
247 		return;
248 	}
249 
250 	flags = skb->len;
251 	flags |= RTL818X_TX_DESC_FLAG_NO_ENC;
252 
253 	flags |= ieee80211_get_tx_rate(dev, info)->hw_value << 24;
254 	if (ieee80211_has_morefrags(tx_hdr->frame_control))
255 		flags |= RTL818X_TX_DESC_FLAG_MOREFRAG;
256 
257 	/* HW will perform RTS-CTS when only RTS flags is set.
258 	 * HW will perform CTS-to-self when both RTS and CTS flags are set.
259 	 * RTS rate and RTS duration will be used also for CTS-to-self.
260 	 */
261 	if (info->control.rates[0].flags & IEEE80211_TX_RC_USE_RTS_CTS) {
262 		flags |= RTL818X_TX_DESC_FLAG_RTS;
263 		flags |= ieee80211_get_rts_cts_rate(dev, info)->hw_value << 19;
264 		rts_dur = ieee80211_rts_duration(dev, priv->vif,
265 						 skb->len, info);
266 	} else if (info->control.rates[0].flags & IEEE80211_TX_RC_USE_CTS_PROTECT) {
267 		flags |= RTL818X_TX_DESC_FLAG_RTS | RTL818X_TX_DESC_FLAG_CTS;
268 		flags |= ieee80211_get_rts_cts_rate(dev, info)->hw_value << 19;
269 		rts_dur = ieee80211_ctstoself_duration(dev, priv->vif,
270 						 skb->len, info);
271 	}
272 
273 	if (info->flags & IEEE80211_TX_CTL_ASSIGN_SEQ) {
274 		if (info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT)
275 			priv->seqno += 0x10;
276 		tx_hdr->seq_ctrl &= cpu_to_le16(IEEE80211_SCTL_FRAG);
277 		tx_hdr->seq_ctrl |= cpu_to_le16(priv->seqno);
278 	}
279 
280 	if (!priv->is_rtl8187b) {
281 		struct rtl8187_tx_hdr *hdr = skb_push(skb, sizeof(*hdr));
282 		hdr->flags = cpu_to_le32(flags);
283 		hdr->len = 0;
284 		hdr->rts_duration = rts_dur;
285 		hdr->retry = cpu_to_le32((info->control.rates[0].count - 1) << 8);
286 		buf = hdr;
287 
288 		ep = 2;
289 	} else {
290 		/* fc needs to be calculated before skb_push() */
291 		unsigned int epmap[4] = { 6, 7, 5, 4 };
292 		u16 fc = le16_to_cpu(tx_hdr->frame_control);
293 
294 		struct rtl8187b_tx_hdr *hdr = skb_push(skb, sizeof(*hdr));
295 		struct ieee80211_rate *txrate =
296 			ieee80211_get_tx_rate(dev, info);
297 		memset(hdr, 0, sizeof(*hdr));
298 		hdr->flags = cpu_to_le32(flags);
299 		hdr->rts_duration = rts_dur;
300 		hdr->retry = cpu_to_le32((info->control.rates[0].count - 1) << 8);
301 		hdr->tx_duration =
302 			ieee80211_generic_frame_duration(dev, priv->vif,
303 							 info->band,
304 							 skb->len, txrate);
305 		buf = hdr;
306 
307 		if ((fc & IEEE80211_FCTL_FTYPE) == IEEE80211_FTYPE_MGMT)
308 			ep = 12;
309 		else
310 			ep = epmap[skb_get_queue_mapping(skb)];
311 	}
312 
313 	info->rate_driver_data[0] = dev;
314 	info->rate_driver_data[1] = urb;
315 
316 	usb_fill_bulk_urb(urb, priv->udev, usb_sndbulkpipe(priv->udev, ep),
317 			  buf, skb->len, rtl8187_tx_cb, skb);
318 	urb->transfer_flags |= URB_ZERO_PACKET;
319 	usb_anchor_urb(urb, &priv->anchored);
320 	rc = usb_submit_urb(urb, GFP_ATOMIC);
321 	if (rc < 0) {
322 		usb_unanchor_urb(urb);
323 		kfree_skb(skb);
324 	}
325 	usb_free_urb(urb);
326 }
327 
328 static void rtl8187_rx_cb(struct urb *urb)
329 {
330 	struct sk_buff *skb = (struct sk_buff *)urb->context;
331 	struct rtl8187_rx_info *info = (struct rtl8187_rx_info *)skb->cb;
332 	struct ieee80211_hw *dev = info->dev;
333 	struct rtl8187_priv *priv = dev->priv;
334 	struct ieee80211_rx_status rx_status = { 0 };
335 	int rate, signal;
336 	u32 flags;
337 	unsigned long f;
338 
339 	spin_lock_irqsave(&priv->rx_queue.lock, f);
340 	__skb_unlink(skb, &priv->rx_queue);
341 	spin_unlock_irqrestore(&priv->rx_queue.lock, f);
342 	skb_put(skb, urb->actual_length);
343 
344 	if (unlikely(urb->status)) {
345 		dev_kfree_skb_irq(skb);
346 		return;
347 	}
348 
349 	if (!priv->is_rtl8187b) {
350 		struct rtl8187_rx_hdr *hdr =
351 			(typeof(hdr))(skb_tail_pointer(skb) - sizeof(*hdr));
352 		flags = le32_to_cpu(hdr->flags);
353 		/* As with the RTL8187B below, the AGC is used to calculate
354 		 * signal strength. In this case, the scaling
355 		 * constants are derived from the output of p54usb.
356 		 */
357 		signal = -4 - ((27 * hdr->agc) >> 6);
358 		rx_status.antenna = (hdr->signal >> 7) & 1;
359 		rx_status.mactime = le64_to_cpu(hdr->mac_time);
360 	} else {
361 		struct rtl8187b_rx_hdr *hdr =
362 			(typeof(hdr))(skb_tail_pointer(skb) - sizeof(*hdr));
363 		/* The Realtek datasheet for the RTL8187B shows that the RX
364 		 * header contains the following quantities: signal quality,
365 		 * RSSI, AGC, the received power in dB, and the measured SNR.
366 		 * In testing, none of these quantities show qualitative
367 		 * agreement with AP signal strength, except for the AGC,
368 		 * which is inversely proportional to the strength of the
369 		 * signal. In the following, the signal strength
370 		 * is derived from the AGC. The arbitrary scaling constants
371 		 * are chosen to make the results close to the values obtained
372 		 * for a BCM4312 using b43 as the driver. The noise is ignored
373 		 * for now.
374 		 */
375 		flags = le32_to_cpu(hdr->flags);
376 		signal = 14 - hdr->agc / 2;
377 		rx_status.antenna = (hdr->rssi >> 7) & 1;
378 		rx_status.mactime = le64_to_cpu(hdr->mac_time);
379 	}
380 
381 	rx_status.signal = signal;
382 	priv->signal = signal;
383 	rate = (flags >> 20) & 0xF;
384 	skb_trim(skb, flags & 0x0FFF);
385 	rx_status.rate_idx = rate;
386 	rx_status.freq = dev->conf.chandef.chan->center_freq;
387 	rx_status.band = dev->conf.chandef.chan->band;
388 	rx_status.flag |= RX_FLAG_MACTIME_START;
389 	if (flags & RTL818X_RX_DESC_FLAG_SPLCP)
390 		rx_status.enc_flags |= RX_ENC_FLAG_SHORTPRE;
391 	if (flags & RTL818X_RX_DESC_FLAG_CRC32_ERR)
392 		rx_status.flag |= RX_FLAG_FAILED_FCS_CRC;
393 	memcpy(IEEE80211_SKB_RXCB(skb), &rx_status, sizeof(rx_status));
394 	ieee80211_rx_irqsafe(dev, skb);
395 
396 	skb = dev_alloc_skb(RTL8187_MAX_RX);
397 	if (unlikely(!skb)) {
398 		/* TODO check rx queue length and refill *somewhere* */
399 		return;
400 	}
401 
402 	info = (struct rtl8187_rx_info *)skb->cb;
403 	info->urb = urb;
404 	info->dev = dev;
405 	urb->transfer_buffer = skb_tail_pointer(skb);
406 	urb->context = skb;
407 	skb_queue_tail(&priv->rx_queue, skb);
408 
409 	usb_anchor_urb(urb, &priv->anchored);
410 	if (usb_submit_urb(urb, GFP_ATOMIC)) {
411 		usb_unanchor_urb(urb);
412 		skb_unlink(skb, &priv->rx_queue);
413 		dev_kfree_skb_irq(skb);
414 	}
415 }
416 
417 static int rtl8187_init_urbs(struct ieee80211_hw *dev)
418 {
419 	struct rtl8187_priv *priv = dev->priv;
420 	struct urb *entry = NULL;
421 	struct sk_buff *skb;
422 	struct rtl8187_rx_info *info;
423 	int ret = 0;
424 
425 	while (skb_queue_len(&priv->rx_queue) < 32) {
426 		skb = __dev_alloc_skb(RTL8187_MAX_RX, GFP_KERNEL);
427 		if (!skb) {
428 			ret = -ENOMEM;
429 			goto err;
430 		}
431 		entry = usb_alloc_urb(0, GFP_KERNEL);
432 		if (!entry) {
433 			ret = -ENOMEM;
434 			goto err;
435 		}
436 		usb_fill_bulk_urb(entry, priv->udev,
437 				  usb_rcvbulkpipe(priv->udev,
438 				  priv->is_rtl8187b ? 3 : 1),
439 				  skb_tail_pointer(skb),
440 				  RTL8187_MAX_RX, rtl8187_rx_cb, skb);
441 		info = (struct rtl8187_rx_info *)skb->cb;
442 		info->urb = entry;
443 		info->dev = dev;
444 		skb_queue_tail(&priv->rx_queue, skb);
445 		usb_anchor_urb(entry, &priv->anchored);
446 		ret = usb_submit_urb(entry, GFP_KERNEL);
447 		usb_put_urb(entry);
448 		if (ret) {
449 			skb_unlink(skb, &priv->rx_queue);
450 			usb_unanchor_urb(entry);
451 			goto err;
452 		}
453 	}
454 	return ret;
455 
456 err:
457 	kfree_skb(skb);
458 	usb_kill_anchored_urbs(&priv->anchored);
459 	return ret;
460 }
461 
462 static void rtl8187b_status_cb(struct urb *urb)
463 {
464 	struct ieee80211_hw *hw = (struct ieee80211_hw *)urb->context;
465 	struct rtl8187_priv *priv = hw->priv;
466 	u64 val;
467 	unsigned int cmd_type;
468 
469 	if (unlikely(urb->status))
470 		return;
471 
472 	/*
473 	 * Read from status buffer:
474 	 *
475 	 * bits [30:31] = cmd type:
476 	 * - 0 indicates tx beacon interrupt
477 	 * - 1 indicates tx close descriptor
478 	 *
479 	 * In the case of tx beacon interrupt:
480 	 * [0:9] = Last Beacon CW
481 	 * [10:29] = reserved
482 	 * [30:31] = 00b
483 	 * [32:63] = Last Beacon TSF
484 	 *
485 	 * If it's tx close descriptor:
486 	 * [0:7] = Packet Retry Count
487 	 * [8:14] = RTS Retry Count
488 	 * [15] = TOK
489 	 * [16:27] = Sequence No
490 	 * [28] = LS
491 	 * [29] = FS
492 	 * [30:31] = 01b
493 	 * [32:47] = unused (reserved?)
494 	 * [48:63] = MAC Used Time
495 	 */
496 	val = le64_to_cpu(priv->b_tx_status.buf);
497 
498 	cmd_type = (val >> 30) & 0x3;
499 	if (cmd_type == 1) {
500 		unsigned int pkt_rc, seq_no;
501 		bool tok;
502 		struct sk_buff *skb;
503 		struct ieee80211_hdr *ieee80211hdr;
504 		unsigned long flags;
505 
506 		pkt_rc = val & 0xFF;
507 		tok = val & (1 << 15);
508 		seq_no = (val >> 16) & 0xFFF;
509 
510 		spin_lock_irqsave(&priv->b_tx_status.queue.lock, flags);
511 		skb_queue_reverse_walk(&priv->b_tx_status.queue, skb) {
512 			ieee80211hdr = (struct ieee80211_hdr *)skb->data;
513 
514 			/*
515 			 * While testing, it was discovered that the seq_no
516 			 * doesn't actually contains the sequence number.
517 			 * Instead of returning just the 12 bits of sequence
518 			 * number, hardware is returning entire sequence control
519 			 * (fragment number plus sequence number) in a 12 bit
520 			 * only field overflowing after some time. As a
521 			 * workaround, just consider the lower bits, and expect
522 			 * it's unlikely we wrongly ack some sent data
523 			 */
524 			if ((le16_to_cpu(ieee80211hdr->seq_ctrl)
525 			    & 0xFFF) == seq_no)
526 				break;
527 		}
528 		if (skb != (struct sk_buff *) &priv->b_tx_status.queue) {
529 			struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
530 
531 			__skb_unlink(skb, &priv->b_tx_status.queue);
532 			if (tok)
533 				info->flags |= IEEE80211_TX_STAT_ACK;
534 			info->status.rates[0].count = pkt_rc + 1;
535 
536 			ieee80211_tx_status_irqsafe(hw, skb);
537 		}
538 		spin_unlock_irqrestore(&priv->b_tx_status.queue.lock, flags);
539 	}
540 
541 	usb_anchor_urb(urb, &priv->anchored);
542 	if (usb_submit_urb(urb, GFP_ATOMIC))
543 		usb_unanchor_urb(urb);
544 }
545 
546 static int rtl8187b_init_status_urb(struct ieee80211_hw *dev)
547 {
548 	struct rtl8187_priv *priv = dev->priv;
549 	struct urb *entry;
550 	int ret = 0;
551 
552 	entry = usb_alloc_urb(0, GFP_KERNEL);
553 	if (!entry)
554 		return -ENOMEM;
555 
556 	usb_fill_bulk_urb(entry, priv->udev, usb_rcvbulkpipe(priv->udev, 9),
557 			  &priv->b_tx_status.buf, sizeof(priv->b_tx_status.buf),
558 			  rtl8187b_status_cb, dev);
559 
560 	usb_anchor_urb(entry, &priv->anchored);
561 	ret = usb_submit_urb(entry, GFP_KERNEL);
562 	if (ret)
563 		usb_unanchor_urb(entry);
564 	usb_free_urb(entry);
565 
566 	return ret;
567 }
568 
569 static void rtl8187_set_anaparam(struct rtl8187_priv *priv, bool rfon)
570 {
571 	u32 anaparam, anaparam2;
572 	u8 anaparam3, reg;
573 
574 	if (!priv->is_rtl8187b) {
575 		if (rfon) {
576 			anaparam = RTL8187_RTL8225_ANAPARAM_ON;
577 			anaparam2 = RTL8187_RTL8225_ANAPARAM2_ON;
578 		} else {
579 			anaparam = RTL8187_RTL8225_ANAPARAM_OFF;
580 			anaparam2 = RTL8187_RTL8225_ANAPARAM2_OFF;
581 		}
582 	} else {
583 		if (rfon) {
584 			anaparam = RTL8187B_RTL8225_ANAPARAM_ON;
585 			anaparam2 = RTL8187B_RTL8225_ANAPARAM2_ON;
586 			anaparam3 = RTL8187B_RTL8225_ANAPARAM3_ON;
587 		} else {
588 			anaparam = RTL8187B_RTL8225_ANAPARAM_OFF;
589 			anaparam2 = RTL8187B_RTL8225_ANAPARAM2_OFF;
590 			anaparam3 = RTL8187B_RTL8225_ANAPARAM3_OFF;
591 		}
592 	}
593 
594 	rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
595 			 RTL818X_EEPROM_CMD_CONFIG);
596 	reg = rtl818x_ioread8(priv, &priv->map->CONFIG3);
597 	reg |= RTL818X_CONFIG3_ANAPARAM_WRITE;
598 	rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg);
599 	rtl818x_iowrite32(priv, &priv->map->ANAPARAM, anaparam);
600 	rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, anaparam2);
601 	if (priv->is_rtl8187b)
602 		rtl818x_iowrite8(priv, &priv->map->ANAPARAM3A, anaparam3);
603 	reg &= ~RTL818X_CONFIG3_ANAPARAM_WRITE;
604 	rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg);
605 	rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
606 			 RTL818X_EEPROM_CMD_NORMAL);
607 }
608 
609 static int rtl8187_cmd_reset(struct ieee80211_hw *dev)
610 {
611 	struct rtl8187_priv *priv = dev->priv;
612 	u8 reg;
613 	int i;
614 
615 	reg = rtl818x_ioread8(priv, &priv->map->CMD);
616 	reg &= (1 << 1);
617 	reg |= RTL818X_CMD_RESET;
618 	rtl818x_iowrite8(priv, &priv->map->CMD, reg);
619 
620 	i = 10;
621 	do {
622 		msleep(2);
623 		if (!(rtl818x_ioread8(priv, &priv->map->CMD) &
624 		      RTL818X_CMD_RESET))
625 			break;
626 	} while (--i);
627 
628 	if (!i) {
629 		wiphy_err(dev->wiphy, "Reset timeout!\n");
630 		return -ETIMEDOUT;
631 	}
632 
633 	/* reload registers from eeprom */
634 	rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_LOAD);
635 
636 	i = 10;
637 	do {
638 		msleep(4);
639 		if (!(rtl818x_ioread8(priv, &priv->map->EEPROM_CMD) &
640 		      RTL818X_EEPROM_CMD_CONFIG))
641 			break;
642 	} while (--i);
643 
644 	if (!i) {
645 		wiphy_err(dev->wiphy, "eeprom reset timeout!\n");
646 		return -ETIMEDOUT;
647 	}
648 
649 	return 0;
650 }
651 
652 static int rtl8187_init_hw(struct ieee80211_hw *dev)
653 {
654 	struct rtl8187_priv *priv = dev->priv;
655 	u8 reg;
656 	int res;
657 
658 	/* reset */
659 	rtl8187_set_anaparam(priv, true);
660 
661 	rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0);
662 
663 	msleep(200);
664 	rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x10);
665 	rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x11);
666 	rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x00);
667 	msleep(200);
668 
669 	res = rtl8187_cmd_reset(dev);
670 	if (res)
671 		return res;
672 
673 	rtl8187_set_anaparam(priv, true);
674 
675 	/* setup card */
676 	rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0);
677 	rtl818x_iowrite8(priv, &priv->map->GPIO0, 0);
678 
679 	rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, (4 << 8));
680 	rtl818x_iowrite8(priv, &priv->map->GPIO0, 1);
681 	rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0);
682 
683 	rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
684 
685 	rtl818x_iowrite16(priv, (__le16 *)0xFFF4, 0xFFFF);
686 	reg = rtl818x_ioread8(priv, &priv->map->CONFIG1);
687 	reg &= 0x3F;
688 	reg |= 0x80;
689 	rtl818x_iowrite8(priv, &priv->map->CONFIG1, reg);
690 
691 	rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
692 
693 	rtl818x_iowrite32(priv, &priv->map->INT_TIMEOUT, 0);
694 	rtl818x_iowrite8(priv, &priv->map->WPA_CONF, 0);
695 	rtl818x_iowrite8(priv, &priv->map->RATE_FALLBACK, 0);
696 
697 	// TODO: set RESP_RATE and BRSR properly
698 	rtl818x_iowrite8(priv, &priv->map->RESP_RATE, (8 << 4) | 0);
699 	rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3);
700 
701 	/* host_usb_init */
702 	rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0);
703 	rtl818x_iowrite8(priv, &priv->map->GPIO0, 0);
704 	reg = rtl818x_ioread8(priv, (u8 *)0xFE53);
705 	rtl818x_iowrite8(priv, (u8 *)0xFE53, reg | (1 << 7));
706 	rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, (4 << 8));
707 	rtl818x_iowrite8(priv, &priv->map->GPIO0, 0x20);
708 	rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0);
709 	rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, 0x80);
710 	rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0x80);
711 	rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x80);
712 	msleep(100);
713 
714 	rtl818x_iowrite32(priv, &priv->map->RF_TIMING, 0x000a8008);
715 	rtl818x_iowrite16(priv, &priv->map->BRSR, 0xFFFF);
716 	rtl818x_iowrite32(priv, &priv->map->RF_PARA, 0x00100044);
717 	rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
718 			 RTL818X_EEPROM_CMD_CONFIG);
719 	rtl818x_iowrite8(priv, &priv->map->CONFIG3, 0x44);
720 	rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
721 			 RTL818X_EEPROM_CMD_NORMAL);
722 	rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FF7);
723 	msleep(100);
724 
725 	priv->rf->init(dev);
726 
727 	rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3);
728 	reg = rtl818x_ioread8(priv, &priv->map->PGSELECT) & ~1;
729 	rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg | 1);
730 	rtl818x_iowrite16(priv, (__le16 *)0xFFFE, 0x10);
731 	rtl818x_iowrite8(priv, &priv->map->TALLY_SEL, 0x80);
732 	rtl818x_iowrite8(priv, (u8 *)0xFFFF, 0x60);
733 	rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg);
734 
735 	return 0;
736 }
737 
738 static const u8 rtl8187b_reg_table[][3] = {
739 	{0xF0, 0x32, 0}, {0xF1, 0x32, 0}, {0xF2, 0x00, 0}, {0xF3, 0x00, 0},
740 	{0xF4, 0x32, 0}, {0xF5, 0x43, 0}, {0xF6, 0x00, 0}, {0xF7, 0x00, 0},
741 	{0xF8, 0x46, 0}, {0xF9, 0xA4, 0}, {0xFA, 0x00, 0}, {0xFB, 0x00, 0},
742 	{0xFC, 0x96, 0}, {0xFD, 0xA4, 0}, {0xFE, 0x00, 0}, {0xFF, 0x00, 0},
743 
744 	{0x58, 0x4B, 1}, {0x59, 0x00, 1}, {0x5A, 0x4B, 1}, {0x5B, 0x00, 1},
745 	{0x60, 0x4B, 1}, {0x61, 0x09, 1}, {0x62, 0x4B, 1}, {0x63, 0x09, 1},
746 	{0xCE, 0x0F, 1}, {0xCF, 0x00, 1}, {0xF0, 0x4E, 1}, {0xF1, 0x01, 1},
747 	{0xF2, 0x02, 1}, {0xF3, 0x03, 1}, {0xF4, 0x04, 1}, {0xF5, 0x05, 1},
748 	{0xF6, 0x06, 1}, {0xF7, 0x07, 1}, {0xF8, 0x08, 1},
749 
750 	{0x4E, 0x00, 2}, {0x0C, 0x04, 2}, {0x21, 0x61, 2}, {0x22, 0x68, 2},
751 	{0x23, 0x6F, 2}, {0x24, 0x76, 2}, {0x25, 0x7D, 2}, {0x26, 0x84, 2},
752 	{0x27, 0x8D, 2}, {0x4D, 0x08, 2}, {0x50, 0x05, 2}, {0x51, 0xF5, 2},
753 	{0x52, 0x04, 2}, {0x53, 0xA0, 2}, {0x54, 0x1F, 2}, {0x55, 0x23, 2},
754 	{0x56, 0x45, 2}, {0x57, 0x67, 2}, {0x58, 0x08, 2}, {0x59, 0x08, 2},
755 	{0x5A, 0x08, 2}, {0x5B, 0x08, 2}, {0x60, 0x08, 2}, {0x61, 0x08, 2},
756 	{0x62, 0x08, 2}, {0x63, 0x08, 2}, {0x64, 0xCF, 2},
757 
758 	{0x5B, 0x40, 0}, {0x84, 0x88, 0}, {0x85, 0x24, 0}, {0x88, 0x54, 0},
759 	{0x8B, 0xB8, 0}, {0x8C, 0x07, 0}, {0x8D, 0x00, 0}, {0x94, 0x1B, 0},
760 	{0x95, 0x12, 0}, {0x96, 0x00, 0}, {0x97, 0x06, 0}, {0x9D, 0x1A, 0},
761 	{0x9F, 0x10, 0}, {0xB4, 0x22, 0}, {0xBE, 0x80, 0}, {0xDB, 0x00, 0},
762 	{0xEE, 0x00, 0}, {0x4C, 0x00, 2},
763 
764 	{0x9F, 0x00, 3}, {0x8C, 0x01, 0}, {0x8D, 0x10, 0}, {0x8E, 0x08, 0},
765 	{0x8F, 0x00, 0}
766 };
767 
768 static int rtl8187b_init_hw(struct ieee80211_hw *dev)
769 {
770 	struct rtl8187_priv *priv = dev->priv;
771 	int res, i;
772 	u8 reg;
773 
774 	rtl8187_set_anaparam(priv, true);
775 
776 	/* Reset PLL sequence on 8187B. Realtek note: reduces power
777 	 * consumption about 30 mA */
778 	rtl818x_iowrite8(priv, (u8 *)0xFF61, 0x10);
779 	reg = rtl818x_ioread8(priv, (u8 *)0xFF62);
780 	rtl818x_iowrite8(priv, (u8 *)0xFF62, reg & ~(1 << 5));
781 	rtl818x_iowrite8(priv, (u8 *)0xFF62, reg | (1 << 5));
782 
783 	res = rtl8187_cmd_reset(dev);
784 	if (res)
785 		return res;
786 
787 	rtl8187_set_anaparam(priv, true);
788 
789 	/* BRSR (Basic Rate Set Register) on 8187B looks to be the same as
790 	 * RESP_RATE on 8187L in Realtek sources: each bit should be each
791 	 * one of the 12 rates, all are enabled */
792 	rtl818x_iowrite16(priv, (__le16 *)0xFF34, 0x0FFF);
793 
794 	reg = rtl818x_ioread8(priv, &priv->map->CW_CONF);
795 	reg |= RTL818X_CW_CONF_PERPACKET_RETRY;
796 	rtl818x_iowrite8(priv, &priv->map->CW_CONF, reg);
797 
798 	/* Auto Rate Fallback Register (ARFR): 1M-54M setting */
799 	rtl818x_iowrite16_idx(priv, (__le16 *)0xFFE0, 0x0FFF, 1);
800 	rtl818x_iowrite8_idx(priv, (u8 *)0xFFE2, 0x00, 1);
801 
802 	rtl818x_iowrite16_idx(priv, (__le16 *)0xFFD4, 0xFFFF, 1);
803 
804 	rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
805 			 RTL818X_EEPROM_CMD_CONFIG);
806 	reg = rtl818x_ioread8(priv, &priv->map->CONFIG1);
807 	rtl818x_iowrite8(priv, &priv->map->CONFIG1, (reg & 0x3F) | 0x80);
808 	rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
809 			 RTL818X_EEPROM_CMD_NORMAL);
810 
811 	rtl818x_iowrite8(priv, &priv->map->WPA_CONF, 0);
812 	for (i = 0; i < ARRAY_SIZE(rtl8187b_reg_table); i++) {
813 		rtl818x_iowrite8_idx(priv,
814 				     (u8 *)(uintptr_t)
815 				     (rtl8187b_reg_table[i][0] | 0xFF00),
816 				     rtl8187b_reg_table[i][1],
817 				     rtl8187b_reg_table[i][2]);
818 	}
819 
820 	rtl818x_iowrite16(priv, &priv->map->TID_AC_MAP, 0xFA50);
821 	rtl818x_iowrite16(priv, &priv->map->INT_MIG, 0);
822 
823 	rtl818x_iowrite32_idx(priv, (__le32 *)0xFFF0, 0, 1);
824 	rtl818x_iowrite32_idx(priv, (__le32 *)0xFFF4, 0, 1);
825 	rtl818x_iowrite8_idx(priv, (u8 *)0xFFF8, 0, 1);
826 
827 	rtl818x_iowrite32(priv, &priv->map->RF_TIMING, 0x00004001);
828 
829 	/* RFSW_CTRL register */
830 	rtl818x_iowrite16_idx(priv, (__le16 *)0xFF72, 0x569A, 2);
831 
832 	rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, 0x0480);
833 	rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0x2488);
834 	rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FFF);
835 	msleep(100);
836 
837 	priv->rf->init(dev);
838 
839 	reg = RTL818X_CMD_TX_ENABLE | RTL818X_CMD_RX_ENABLE;
840 	rtl818x_iowrite8(priv, &priv->map->CMD, reg);
841 	rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0xFFFF);
842 
843 	rtl818x_iowrite8(priv, (u8 *)0xFE41, 0xF4);
844 	rtl818x_iowrite8(priv, (u8 *)0xFE40, 0x00);
845 	rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x00);
846 	rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x01);
847 	rtl818x_iowrite8(priv, (u8 *)0xFE40, 0x0F);
848 	rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x00);
849 	rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x01);
850 
851 	reg = rtl818x_ioread8(priv, (u8 *)0xFFDB);
852 	rtl818x_iowrite8(priv, (u8 *)0xFFDB, reg | (1 << 2));
853 	rtl818x_iowrite16_idx(priv, (__le16 *)0xFF72, 0x59FA, 3);
854 	rtl818x_iowrite16_idx(priv, (__le16 *)0xFF74, 0x59D2, 3);
855 	rtl818x_iowrite16_idx(priv, (__le16 *)0xFF76, 0x59D2, 3);
856 	rtl818x_iowrite16_idx(priv, (__le16 *)0xFF78, 0x19FA, 3);
857 	rtl818x_iowrite16_idx(priv, (__le16 *)0xFF7A, 0x19FA, 3);
858 	rtl818x_iowrite16_idx(priv, (__le16 *)0xFF7C, 0x00D0, 3);
859 	rtl818x_iowrite8(priv, (u8 *)0xFF61, 0);
860 	rtl818x_iowrite8_idx(priv, (u8 *)0xFF80, 0x0F, 1);
861 	rtl818x_iowrite8_idx(priv, (u8 *)0xFF83, 0x03, 1);
862 	rtl818x_iowrite8(priv, (u8 *)0xFFDA, 0x10);
863 	rtl818x_iowrite8_idx(priv, (u8 *)0xFF4D, 0x08, 2);
864 
865 	rtl818x_iowrite32(priv, &priv->map->HSSI_PARA, 0x0600321B);
866 
867 	rtl818x_iowrite16_idx(priv, (__le16 *)0xFFEC, 0x0800, 1);
868 
869 	priv->slot_time = 0x9;
870 	priv->aifsn[0] = 2; /* AIFSN[AC_VO] */
871 	priv->aifsn[1] = 2; /* AIFSN[AC_VI] */
872 	priv->aifsn[2] = 7; /* AIFSN[AC_BK] */
873 	priv->aifsn[3] = 3; /* AIFSN[AC_BE] */
874 	rtl818x_iowrite8(priv, &priv->map->ACM_CONTROL, 0);
875 
876 	/* ENEDCA flag must always be set, transmit issues? */
877 	rtl818x_iowrite8(priv, &priv->map->MSR, RTL818X_MSR_ENEDCA);
878 
879 	return 0;
880 }
881 
882 static void rtl8187_work(struct work_struct *work)
883 {
884 	/* The RTL8187 returns the retry count through register 0xFFFA. In
885 	 * addition, it appears to be a cumulative retry count, not the
886 	 * value for the current TX packet. When multiple TX entries are
887 	 * waiting in the queue, the retry count will be the total for all.
888 	 * The "error" may matter for purposes of rate setting, but there is
889 	 * no other choice with this hardware.
890 	 */
891 	struct rtl8187_priv *priv = container_of(work, struct rtl8187_priv,
892 				    work.work);
893 	struct ieee80211_tx_info *info;
894 	struct ieee80211_hw *dev = priv->dev;
895 	static u16 retry;
896 	u16 tmp;
897 	u16 avg_retry;
898 	int length;
899 
900 	mutex_lock(&priv->conf_mutex);
901 	tmp = rtl818x_ioread16(priv, (__le16 *)0xFFFA);
902 	length = skb_queue_len(&priv->b_tx_status.queue);
903 	if (unlikely(!length))
904 		length = 1;
905 	if (unlikely(tmp < retry))
906 		tmp = retry;
907 	avg_retry = (tmp - retry) / length;
908 	while (skb_queue_len(&priv->b_tx_status.queue) > 0) {
909 		struct sk_buff *old_skb;
910 
911 		old_skb = skb_dequeue(&priv->b_tx_status.queue);
912 		info = IEEE80211_SKB_CB(old_skb);
913 		info->status.rates[0].count = avg_retry + 1;
914 		if (info->status.rates[0].count > RETRY_COUNT)
915 			info->flags &= ~IEEE80211_TX_STAT_ACK;
916 		ieee80211_tx_status_irqsafe(dev, old_skb);
917 	}
918 	retry = tmp;
919 	mutex_unlock(&priv->conf_mutex);
920 }
921 
922 static int rtl8187_start(struct ieee80211_hw *dev)
923 {
924 	struct rtl8187_priv *priv = dev->priv;
925 	u32 reg;
926 	int ret;
927 
928 	mutex_lock(&priv->conf_mutex);
929 
930 	ret = (!priv->is_rtl8187b) ? rtl8187_init_hw(dev) :
931 				     rtl8187b_init_hw(dev);
932 	if (ret)
933 		goto rtl8187_start_exit;
934 
935 	init_usb_anchor(&priv->anchored);
936 	priv->dev = dev;
937 
938 	if (priv->is_rtl8187b) {
939 		reg = RTL818X_RX_CONF_MGMT |
940 		      RTL818X_RX_CONF_DATA |
941 		      RTL818X_RX_CONF_BROADCAST |
942 		      RTL818X_RX_CONF_NICMAC |
943 		      RTL818X_RX_CONF_BSSID |
944 		      (7 << 13 /* RX FIFO threshold NONE */) |
945 		      (7 << 10 /* MAX RX DMA */) |
946 		      RTL818X_RX_CONF_RX_AUTORESETPHY |
947 		      RTL818X_RX_CONF_ONLYERLPKT;
948 		priv->rx_conf = reg;
949 		rtl818x_iowrite32(priv, &priv->map->RX_CONF, reg);
950 
951 		reg = rtl818x_ioread8(priv, &priv->map->TX_AGC_CTL);
952 		reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_GAIN;
953 		reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL;
954 		reg &= ~RTL818X_TX_AGC_CTL_FEEDBACK_ANT;
955 		rtl818x_iowrite8(priv, &priv->map->TX_AGC_CTL, reg);
956 
957 		rtl818x_iowrite32(priv, &priv->map->TX_CONF,
958 				  RTL818X_TX_CONF_HW_SEQNUM |
959 				  RTL818X_TX_CONF_DISREQQSIZE |
960 				  (RETRY_COUNT << 8  /* short retry limit */) |
961 				  (RETRY_COUNT << 0  /* long retry limit */) |
962 				  (7 << 21 /* MAX TX DMA */));
963 		ret = rtl8187_init_urbs(dev);
964 		if (ret)
965 			goto rtl8187_start_exit;
966 		ret = rtl8187b_init_status_urb(dev);
967 		if (ret)
968 			usb_kill_anchored_urbs(&priv->anchored);
969 		goto rtl8187_start_exit;
970 	}
971 
972 	rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0xFFFF);
973 
974 	rtl818x_iowrite32(priv, &priv->map->MAR[0], ~0);
975 	rtl818x_iowrite32(priv, &priv->map->MAR[1], ~0);
976 
977 	ret = rtl8187_init_urbs(dev);
978 	if (ret)
979 		goto rtl8187_start_exit;
980 
981 	reg = RTL818X_RX_CONF_ONLYERLPKT |
982 	      RTL818X_RX_CONF_RX_AUTORESETPHY |
983 	      RTL818X_RX_CONF_BSSID |
984 	      RTL818X_RX_CONF_MGMT |
985 	      RTL818X_RX_CONF_DATA |
986 	      (7 << 13 /* RX FIFO threshold NONE */) |
987 	      (7 << 10 /* MAX RX DMA */) |
988 	      RTL818X_RX_CONF_BROADCAST |
989 	      RTL818X_RX_CONF_NICMAC;
990 
991 	priv->rx_conf = reg;
992 	rtl818x_iowrite32(priv, &priv->map->RX_CONF, reg);
993 
994 	reg = rtl818x_ioread8(priv, &priv->map->CW_CONF);
995 	reg &= ~RTL818X_CW_CONF_PERPACKET_CW;
996 	reg |= RTL818X_CW_CONF_PERPACKET_RETRY;
997 	rtl818x_iowrite8(priv, &priv->map->CW_CONF, reg);
998 
999 	reg = rtl818x_ioread8(priv, &priv->map->TX_AGC_CTL);
1000 	reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_GAIN;
1001 	reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL;
1002 	reg &= ~RTL818X_TX_AGC_CTL_FEEDBACK_ANT;
1003 	rtl818x_iowrite8(priv, &priv->map->TX_AGC_CTL, reg);
1004 
1005 	reg  = RTL818X_TX_CONF_CW_MIN |
1006 	       (7 << 21 /* MAX TX DMA */) |
1007 	       RTL818X_TX_CONF_NO_ICV;
1008 	rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg);
1009 
1010 	reg = rtl818x_ioread8(priv, &priv->map->CMD);
1011 	reg |= RTL818X_CMD_TX_ENABLE;
1012 	reg |= RTL818X_CMD_RX_ENABLE;
1013 	rtl818x_iowrite8(priv, &priv->map->CMD, reg);
1014 	INIT_DELAYED_WORK(&priv->work, rtl8187_work);
1015 
1016 rtl8187_start_exit:
1017 	mutex_unlock(&priv->conf_mutex);
1018 	return ret;
1019 }
1020 
1021 static void rtl8187_stop(struct ieee80211_hw *dev)
1022 {
1023 	struct rtl8187_priv *priv = dev->priv;
1024 	struct sk_buff *skb;
1025 	u32 reg;
1026 
1027 	mutex_lock(&priv->conf_mutex);
1028 	rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0);
1029 
1030 	reg = rtl818x_ioread8(priv, &priv->map->CMD);
1031 	reg &= ~RTL818X_CMD_TX_ENABLE;
1032 	reg &= ~RTL818X_CMD_RX_ENABLE;
1033 	rtl818x_iowrite8(priv, &priv->map->CMD, reg);
1034 
1035 	priv->rf->stop(dev);
1036 	rtl8187_set_anaparam(priv, false);
1037 
1038 	rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
1039 	reg = rtl818x_ioread8(priv, &priv->map->CONFIG4);
1040 	rtl818x_iowrite8(priv, &priv->map->CONFIG4, reg | RTL818X_CONFIG4_VCOOFF);
1041 	rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
1042 
1043 	while ((skb = skb_dequeue(&priv->b_tx_status.queue)))
1044 		dev_kfree_skb_any(skb);
1045 
1046 	usb_kill_anchored_urbs(&priv->anchored);
1047 	mutex_unlock(&priv->conf_mutex);
1048 
1049 	if (!priv->is_rtl8187b)
1050 		cancel_delayed_work_sync(&priv->work);
1051 }
1052 
1053 static u64 rtl8187_get_tsf(struct ieee80211_hw *dev, struct ieee80211_vif *vif)
1054 {
1055 	struct rtl8187_priv *priv = dev->priv;
1056 
1057 	return rtl818x_ioread32(priv, &priv->map->TSFT[0]) |
1058 	       (u64)(rtl818x_ioread32(priv, &priv->map->TSFT[1])) << 32;
1059 }
1060 
1061 
1062 static void rtl8187_beacon_work(struct work_struct *work)
1063 {
1064 	struct rtl8187_vif *vif_priv =
1065 		container_of(work, struct rtl8187_vif, beacon_work.work);
1066 	struct ieee80211_vif *vif =
1067 		container_of((void *)vif_priv, struct ieee80211_vif, drv_priv);
1068 	struct ieee80211_hw *dev = vif_priv->dev;
1069 	struct ieee80211_mgmt *mgmt;
1070 	struct sk_buff *skb;
1071 
1072 	/* don't overflow the tx ring */
1073 	if (ieee80211_queue_stopped(dev, 0))
1074 		goto resched;
1075 
1076 	/* grab a fresh beacon */
1077 	skb = ieee80211_beacon_get(dev, vif);
1078 	if (!skb)
1079 		goto resched;
1080 
1081 	/*
1082 	 * update beacon timestamp w/ TSF value
1083 	 * TODO: make hardware update beacon timestamp
1084 	 */
1085 	mgmt = (struct ieee80211_mgmt *)skb->data;
1086 	mgmt->u.beacon.timestamp = cpu_to_le64(rtl8187_get_tsf(dev, vif));
1087 
1088 	/* TODO: use actual beacon queue */
1089 	skb_set_queue_mapping(skb, 0);
1090 
1091 	rtl8187_tx(dev, NULL, skb);
1092 
1093 resched:
1094 	/*
1095 	 * schedule next beacon
1096 	 * TODO: use hardware support for beacon timing
1097 	 */
1098 	schedule_delayed_work(&vif_priv->beacon_work,
1099 			usecs_to_jiffies(1024 * vif->bss_conf.beacon_int));
1100 }
1101 
1102 
1103 static int rtl8187_add_interface(struct ieee80211_hw *dev,
1104 				 struct ieee80211_vif *vif)
1105 {
1106 	struct rtl8187_priv *priv = dev->priv;
1107 	struct rtl8187_vif *vif_priv;
1108 	int i;
1109 	int ret = -EOPNOTSUPP;
1110 
1111 	mutex_lock(&priv->conf_mutex);
1112 	if (priv->vif)
1113 		goto exit;
1114 
1115 	switch (vif->type) {
1116 	case NL80211_IFTYPE_STATION:
1117 	case NL80211_IFTYPE_ADHOC:
1118 		break;
1119 	default:
1120 		goto exit;
1121 	}
1122 
1123 	ret = 0;
1124 	priv->vif = vif;
1125 
1126 	/* Initialize driver private area */
1127 	vif_priv = (struct rtl8187_vif *)&vif->drv_priv;
1128 	vif_priv->dev = dev;
1129 	INIT_DELAYED_WORK(&vif_priv->beacon_work, rtl8187_beacon_work);
1130 	vif_priv->enable_beacon = false;
1131 
1132 
1133 	rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
1134 	for (i = 0; i < ETH_ALEN; i++)
1135 		rtl818x_iowrite8(priv, &priv->map->MAC[i],
1136 				 ((u8 *)vif->addr)[i]);
1137 	rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
1138 
1139 exit:
1140 	mutex_unlock(&priv->conf_mutex);
1141 	return ret;
1142 }
1143 
1144 static void rtl8187_remove_interface(struct ieee80211_hw *dev,
1145 				     struct ieee80211_vif *vif)
1146 {
1147 	struct rtl8187_priv *priv = dev->priv;
1148 	mutex_lock(&priv->conf_mutex);
1149 	priv->vif = NULL;
1150 	mutex_unlock(&priv->conf_mutex);
1151 }
1152 
1153 static int rtl8187_config(struct ieee80211_hw *dev, u32 changed)
1154 {
1155 	struct rtl8187_priv *priv = dev->priv;
1156 	struct ieee80211_conf *conf = &dev->conf;
1157 	u32 reg;
1158 
1159 	mutex_lock(&priv->conf_mutex);
1160 	reg = rtl818x_ioread32(priv, &priv->map->TX_CONF);
1161 	/* Enable TX loopback on MAC level to avoid TX during channel
1162 	 * changes, as this has be seen to causes problems and the
1163 	 * card will stop work until next reset
1164 	 */
1165 	rtl818x_iowrite32(priv, &priv->map->TX_CONF,
1166 			  reg | RTL818X_TX_CONF_LOOPBACK_MAC);
1167 	priv->rf->set_chan(dev, conf);
1168 	msleep(10);
1169 	rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg);
1170 
1171 	rtl818x_iowrite16(priv, &priv->map->ATIM_WND, 2);
1172 	rtl818x_iowrite16(priv, &priv->map->ATIMTR_INTERVAL, 100);
1173 	rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL, 100);
1174 	rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL_TIME, 100);
1175 	mutex_unlock(&priv->conf_mutex);
1176 	return 0;
1177 }
1178 
1179 /*
1180  * With 8187B, AC_*_PARAM clashes with FEMR definition in struct rtl818x_csr for
1181  * example. Thus we have to use raw values for AC_*_PARAM register addresses.
1182  */
1183 static __le32 *rtl8187b_ac_addr[4] = {
1184 	(__le32 *) 0xFFF0, /* AC_VO */
1185 	(__le32 *) 0xFFF4, /* AC_VI */
1186 	(__le32 *) 0xFFFC, /* AC_BK */
1187 	(__le32 *) 0xFFF8, /* AC_BE */
1188 };
1189 
1190 #define SIFS_TIME 0xa
1191 
1192 static void rtl8187_conf_erp(struct rtl8187_priv *priv, bool use_short_slot,
1193 			     bool use_short_preamble)
1194 {
1195 	if (priv->is_rtl8187b) {
1196 		u8 difs, eifs;
1197 		u16 ack_timeout;
1198 		int queue;
1199 
1200 		if (use_short_slot) {
1201 			priv->slot_time = 0x9;
1202 			difs = 0x1c;
1203 			eifs = 0x53;
1204 		} else {
1205 			priv->slot_time = 0x14;
1206 			difs = 0x32;
1207 			eifs = 0x5b;
1208 		}
1209 		rtl818x_iowrite8(priv, &priv->map->SIFS, 0x22);
1210 		rtl818x_iowrite8(priv, &priv->map->SLOT, priv->slot_time);
1211 		rtl818x_iowrite8(priv, &priv->map->DIFS, difs);
1212 
1213 		/*
1214 		 * BRSR+1 on 8187B is in fact EIFS register
1215 		 * Value in units of 4 us
1216 		 */
1217 		rtl818x_iowrite8(priv, (u8 *)&priv->map->BRSR + 1, eifs);
1218 
1219 		/*
1220 		 * For 8187B, CARRIER_SENSE_COUNTER is in fact ack timeout
1221 		 * register. In units of 4 us like eifs register
1222 		 * ack_timeout = ack duration + plcp + difs + preamble
1223 		 */
1224 		ack_timeout = 112 + 48 + difs;
1225 		if (use_short_preamble)
1226 			ack_timeout += 72;
1227 		else
1228 			ack_timeout += 144;
1229 		rtl818x_iowrite8(priv, &priv->map->CARRIER_SENSE_COUNTER,
1230 				 DIV_ROUND_UP(ack_timeout, 4));
1231 
1232 		for (queue = 0; queue < 4; queue++)
1233 			rtl818x_iowrite8(priv, (u8 *) rtl8187b_ac_addr[queue],
1234 					 priv->aifsn[queue] * priv->slot_time +
1235 					 SIFS_TIME);
1236 	} else {
1237 		rtl818x_iowrite8(priv, &priv->map->SIFS, 0x22);
1238 		if (use_short_slot) {
1239 			rtl818x_iowrite8(priv, &priv->map->SLOT, 0x9);
1240 			rtl818x_iowrite8(priv, &priv->map->DIFS, 0x14);
1241 			rtl818x_iowrite8(priv, &priv->map->EIFS, 91 - 0x14);
1242 		} else {
1243 			rtl818x_iowrite8(priv, &priv->map->SLOT, 0x14);
1244 			rtl818x_iowrite8(priv, &priv->map->DIFS, 0x24);
1245 			rtl818x_iowrite8(priv, &priv->map->EIFS, 91 - 0x24);
1246 		}
1247 	}
1248 }
1249 
1250 static void rtl8187_bss_info_changed(struct ieee80211_hw *dev,
1251 				     struct ieee80211_vif *vif,
1252 				     struct ieee80211_bss_conf *info,
1253 				     u32 changed)
1254 {
1255 	struct rtl8187_priv *priv = dev->priv;
1256 	struct rtl8187_vif *vif_priv;
1257 	int i;
1258 	u8 reg;
1259 
1260 	vif_priv = (struct rtl8187_vif *)&vif->drv_priv;
1261 
1262 	if (changed & BSS_CHANGED_BSSID) {
1263 		mutex_lock(&priv->conf_mutex);
1264 		for (i = 0; i < ETH_ALEN; i++)
1265 			rtl818x_iowrite8(priv, &priv->map->BSSID[i],
1266 					 info->bssid[i]);
1267 
1268 		if (priv->is_rtl8187b)
1269 			reg = RTL818X_MSR_ENEDCA;
1270 		else
1271 			reg = 0;
1272 
1273 		if (is_valid_ether_addr(info->bssid)) {
1274 			if (vif->type == NL80211_IFTYPE_ADHOC)
1275 				reg |= RTL818X_MSR_ADHOC;
1276 			else
1277 				reg |= RTL818X_MSR_INFRA;
1278 		}
1279 		else
1280 			reg |= RTL818X_MSR_NO_LINK;
1281 
1282 		rtl818x_iowrite8(priv, &priv->map->MSR, reg);
1283 
1284 		mutex_unlock(&priv->conf_mutex);
1285 	}
1286 
1287 	if (changed & (BSS_CHANGED_ERP_SLOT | BSS_CHANGED_ERP_PREAMBLE))
1288 		rtl8187_conf_erp(priv, info->use_short_slot,
1289 				 info->use_short_preamble);
1290 
1291 	if (changed & BSS_CHANGED_BEACON_ENABLED)
1292 		vif_priv->enable_beacon = info->enable_beacon;
1293 
1294 	if (changed & (BSS_CHANGED_BEACON_ENABLED | BSS_CHANGED_BEACON)) {
1295 		cancel_delayed_work_sync(&vif_priv->beacon_work);
1296 		if (vif_priv->enable_beacon)
1297 			schedule_work(&vif_priv->beacon_work.work);
1298 	}
1299 
1300 }
1301 
1302 static u64 rtl8187_prepare_multicast(struct ieee80211_hw *dev,
1303 				     struct netdev_hw_addr_list *mc_list)
1304 {
1305 	return netdev_hw_addr_list_count(mc_list);
1306 }
1307 
1308 static void rtl8187_configure_filter(struct ieee80211_hw *dev,
1309 				     unsigned int changed_flags,
1310 				     unsigned int *total_flags,
1311 				     u64 multicast)
1312 {
1313 	struct rtl8187_priv *priv = dev->priv;
1314 
1315 	if (changed_flags & FIF_FCSFAIL)
1316 		priv->rx_conf ^= RTL818X_RX_CONF_FCS;
1317 	if (changed_flags & FIF_CONTROL)
1318 		priv->rx_conf ^= RTL818X_RX_CONF_CTRL;
1319 	if (*total_flags & FIF_OTHER_BSS ||
1320 	    *total_flags & FIF_ALLMULTI || multicast > 0)
1321 		priv->rx_conf |= RTL818X_RX_CONF_MONITOR;
1322 	else
1323 		priv->rx_conf &= ~RTL818X_RX_CONF_MONITOR;
1324 
1325 	*total_flags = 0;
1326 
1327 	if (priv->rx_conf & RTL818X_RX_CONF_FCS)
1328 		*total_flags |= FIF_FCSFAIL;
1329 	if (priv->rx_conf & RTL818X_RX_CONF_CTRL)
1330 		*total_flags |= FIF_CONTROL;
1331 	if (priv->rx_conf & RTL818X_RX_CONF_MONITOR) {
1332 		*total_flags |= FIF_OTHER_BSS;
1333 		*total_flags |= FIF_ALLMULTI;
1334 	}
1335 
1336 	rtl818x_iowrite32_async(priv, &priv->map->RX_CONF, priv->rx_conf);
1337 }
1338 
1339 static int rtl8187_conf_tx(struct ieee80211_hw *dev,
1340 			   struct ieee80211_vif *vif, u16 queue,
1341 			   const struct ieee80211_tx_queue_params *params)
1342 {
1343 	struct rtl8187_priv *priv = dev->priv;
1344 	u8 cw_min, cw_max;
1345 
1346 	if (queue > 3)
1347 		return -EINVAL;
1348 
1349 	cw_min = fls(params->cw_min);
1350 	cw_max = fls(params->cw_max);
1351 
1352 	if (priv->is_rtl8187b) {
1353 		priv->aifsn[queue] = params->aifs;
1354 
1355 		/*
1356 		 * This is the structure of AC_*_PARAM registers in 8187B:
1357 		 * - TXOP limit field, bit offset = 16
1358 		 * - ECWmax, bit offset = 12
1359 		 * - ECWmin, bit offset = 8
1360 		 * - AIFS, bit offset = 0
1361 		 */
1362 		rtl818x_iowrite32(priv, rtl8187b_ac_addr[queue],
1363 				  (params->txop << 16) | (cw_max << 12) |
1364 				  (cw_min << 8) | (params->aifs *
1365 				  priv->slot_time + SIFS_TIME));
1366 	} else {
1367 		if (queue != 0)
1368 			return -EINVAL;
1369 
1370 		rtl818x_iowrite8(priv, &priv->map->CW_VAL,
1371 				 cw_min | (cw_max << 4));
1372 	}
1373 	return 0;
1374 }
1375 
1376 
1377 static const struct ieee80211_ops rtl8187_ops = {
1378 	.tx			= rtl8187_tx,
1379 	.start			= rtl8187_start,
1380 	.stop			= rtl8187_stop,
1381 	.add_interface		= rtl8187_add_interface,
1382 	.remove_interface	= rtl8187_remove_interface,
1383 	.config			= rtl8187_config,
1384 	.bss_info_changed	= rtl8187_bss_info_changed,
1385 	.prepare_multicast	= rtl8187_prepare_multicast,
1386 	.configure_filter	= rtl8187_configure_filter,
1387 	.conf_tx		= rtl8187_conf_tx,
1388 	.rfkill_poll		= rtl8187_rfkill_poll,
1389 	.get_tsf		= rtl8187_get_tsf,
1390 };
1391 
1392 static void rtl8187_eeprom_register_read(struct eeprom_93cx6 *eeprom)
1393 {
1394 	struct ieee80211_hw *dev = eeprom->data;
1395 	struct rtl8187_priv *priv = dev->priv;
1396 	u8 reg = rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
1397 
1398 	eeprom->reg_data_in = reg & RTL818X_EEPROM_CMD_WRITE;
1399 	eeprom->reg_data_out = reg & RTL818X_EEPROM_CMD_READ;
1400 	eeprom->reg_data_clock = reg & RTL818X_EEPROM_CMD_CK;
1401 	eeprom->reg_chip_select = reg & RTL818X_EEPROM_CMD_CS;
1402 }
1403 
1404 static void rtl8187_eeprom_register_write(struct eeprom_93cx6 *eeprom)
1405 {
1406 	struct ieee80211_hw *dev = eeprom->data;
1407 	struct rtl8187_priv *priv = dev->priv;
1408 	u8 reg = RTL818X_EEPROM_CMD_PROGRAM;
1409 
1410 	if (eeprom->reg_data_in)
1411 		reg |= RTL818X_EEPROM_CMD_WRITE;
1412 	if (eeprom->reg_data_out)
1413 		reg |= RTL818X_EEPROM_CMD_READ;
1414 	if (eeprom->reg_data_clock)
1415 		reg |= RTL818X_EEPROM_CMD_CK;
1416 	if (eeprom->reg_chip_select)
1417 		reg |= RTL818X_EEPROM_CMD_CS;
1418 
1419 	rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, reg);
1420 	udelay(10);
1421 }
1422 
1423 static int rtl8187_probe(struct usb_interface *intf,
1424 				   const struct usb_device_id *id)
1425 {
1426 	struct usb_device *udev = interface_to_usbdev(intf);
1427 	struct ieee80211_hw *dev;
1428 	struct rtl8187_priv *priv;
1429 	struct eeprom_93cx6 eeprom;
1430 	struct ieee80211_channel *channel;
1431 	const char *chip_name;
1432 	u16 txpwr, reg;
1433 	u16 product_id = le16_to_cpu(udev->descriptor.idProduct);
1434 	int err, i;
1435 	u8 mac_addr[ETH_ALEN];
1436 
1437 	dev = ieee80211_alloc_hw(sizeof(*priv), &rtl8187_ops);
1438 	if (!dev) {
1439 		printk(KERN_ERR "rtl8187: ieee80211 alloc failed\n");
1440 		return -ENOMEM;
1441 	}
1442 
1443 	priv = dev->priv;
1444 	priv->is_rtl8187b = (id->driver_info == DEVICE_RTL8187B);
1445 
1446 	/* allocate "DMA aware" buffer for register accesses */
1447 	priv->io_dmabuf = kmalloc(sizeof(*priv->io_dmabuf), GFP_KERNEL);
1448 	if (!priv->io_dmabuf) {
1449 		err = -ENOMEM;
1450 		goto err_free_dev;
1451 	}
1452 	mutex_init(&priv->io_mutex);
1453 
1454 	SET_IEEE80211_DEV(dev, &intf->dev);
1455 	usb_set_intfdata(intf, dev);
1456 	priv->udev = udev;
1457 
1458 	usb_get_dev(udev);
1459 
1460 	skb_queue_head_init(&priv->rx_queue);
1461 
1462 	BUILD_BUG_ON(sizeof(priv->channels) != sizeof(rtl818x_channels));
1463 	BUILD_BUG_ON(sizeof(priv->rates) != sizeof(rtl818x_rates));
1464 
1465 	memcpy(priv->channels, rtl818x_channels, sizeof(rtl818x_channels));
1466 	memcpy(priv->rates, rtl818x_rates, sizeof(rtl818x_rates));
1467 	priv->map = (struct rtl818x_csr *)0xFF00;
1468 
1469 	priv->band.band = NL80211_BAND_2GHZ;
1470 	priv->band.channels = priv->channels;
1471 	priv->band.n_channels = ARRAY_SIZE(rtl818x_channels);
1472 	priv->band.bitrates = priv->rates;
1473 	priv->band.n_bitrates = ARRAY_SIZE(rtl818x_rates);
1474 	dev->wiphy->bands[NL80211_BAND_2GHZ] = &priv->band;
1475 
1476 
1477 	ieee80211_hw_set(dev, RX_INCLUDES_FCS);
1478 	ieee80211_hw_set(dev, HOST_BROADCAST_PS_BUFFERING);
1479 	ieee80211_hw_set(dev, SIGNAL_DBM);
1480 	/* Initialize rate-control variables */
1481 	dev->max_rates = 1;
1482 	dev->max_rate_tries = RETRY_COUNT;
1483 
1484 	eeprom.data = dev;
1485 	eeprom.register_read = rtl8187_eeprom_register_read;
1486 	eeprom.register_write = rtl8187_eeprom_register_write;
1487 	if (rtl818x_ioread32(priv, &priv->map->RX_CONF) & (1 << 6))
1488 		eeprom.width = PCI_EEPROM_WIDTH_93C66;
1489 	else
1490 		eeprom.width = PCI_EEPROM_WIDTH_93C46;
1491 
1492 	rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
1493 	udelay(10);
1494 
1495 	eeprom_93cx6_multiread(&eeprom, RTL8187_EEPROM_MAC_ADDR,
1496 			       (__le16 __force *)mac_addr, 3);
1497 	if (!is_valid_ether_addr(mac_addr)) {
1498 		printk(KERN_WARNING "rtl8187: Invalid hwaddr! Using randomly "
1499 		       "generated MAC address\n");
1500 		eth_random_addr(mac_addr);
1501 	}
1502 	SET_IEEE80211_PERM_ADDR(dev, mac_addr);
1503 
1504 	channel = priv->channels;
1505 	for (i = 0; i < 3; i++) {
1506 		eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_1 + i,
1507 				  &txpwr);
1508 		(*channel++).hw_value = txpwr & 0xFF;
1509 		(*channel++).hw_value = txpwr >> 8;
1510 	}
1511 	for (i = 0; i < 2; i++) {
1512 		eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_4 + i,
1513 				  &txpwr);
1514 		(*channel++).hw_value = txpwr & 0xFF;
1515 		(*channel++).hw_value = txpwr >> 8;
1516 	}
1517 
1518 	eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_BASE,
1519 			  &priv->txpwr_base);
1520 
1521 	reg = rtl818x_ioread8(priv, &priv->map->PGSELECT) & ~1;
1522 	rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg | 1);
1523 	/* 0 means asic B-cut, we should use SW 3 wire
1524 	 * bit-by-bit banging for radio. 1 means we can use
1525 	 * USB specific request to write radio registers */
1526 	priv->asic_rev = rtl818x_ioread8(priv, (u8 *)0xFFFE) & 0x3;
1527 	rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg);
1528 	rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
1529 
1530 	if (!priv->is_rtl8187b) {
1531 		u32 reg32;
1532 		reg32 = rtl818x_ioread32(priv, &priv->map->TX_CONF);
1533 		reg32 &= RTL818X_TX_CONF_HWVER_MASK;
1534 		switch (reg32) {
1535 		case RTL818X_TX_CONF_R8187vD_B:
1536 			/* Some RTL8187B devices have a USB ID of 0x8187
1537 			 * detect them here */
1538 			chip_name = "RTL8187BvB(early)";
1539 			priv->is_rtl8187b = 1;
1540 			priv->hw_rev = RTL8187BvB;
1541 			break;
1542 		case RTL818X_TX_CONF_R8187vD:
1543 			chip_name = "RTL8187vD";
1544 			break;
1545 		default:
1546 			chip_name = "RTL8187vB (default)";
1547 		}
1548        } else {
1549 		/*
1550 		 * Force USB request to write radio registers for 8187B, Realtek
1551 		 * only uses it in their sources
1552 		 */
1553 		/*if (priv->asic_rev == 0) {
1554 			printk(KERN_WARNING "rtl8187: Forcing use of USB "
1555 			       "requests to write to radio registers\n");
1556 			priv->asic_rev = 1;
1557 		}*/
1558 		switch (rtl818x_ioread8(priv, (u8 *)0xFFE1)) {
1559 		case RTL818X_R8187B_B:
1560 			chip_name = "RTL8187BvB";
1561 			priv->hw_rev = RTL8187BvB;
1562 			break;
1563 		case RTL818X_R8187B_D:
1564 			chip_name = "RTL8187BvD";
1565 			priv->hw_rev = RTL8187BvD;
1566 			break;
1567 		case RTL818X_R8187B_E:
1568 			chip_name = "RTL8187BvE";
1569 			priv->hw_rev = RTL8187BvE;
1570 			break;
1571 		default:
1572 			chip_name = "RTL8187BvB (default)";
1573 			priv->hw_rev = RTL8187BvB;
1574 		}
1575 	}
1576 
1577 	if (!priv->is_rtl8187b) {
1578 		for (i = 0; i < 2; i++) {
1579 			eeprom_93cx6_read(&eeprom,
1580 					  RTL8187_EEPROM_TXPWR_CHAN_6 + i,
1581 					  &txpwr);
1582 			(*channel++).hw_value = txpwr & 0xFF;
1583 			(*channel++).hw_value = txpwr >> 8;
1584 		}
1585 	} else {
1586 		eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_6,
1587 				  &txpwr);
1588 		(*channel++).hw_value = txpwr & 0xFF;
1589 
1590 		eeprom_93cx6_read(&eeprom, 0x0A, &txpwr);
1591 		(*channel++).hw_value = txpwr & 0xFF;
1592 
1593 		eeprom_93cx6_read(&eeprom, 0x1C, &txpwr);
1594 		(*channel++).hw_value = txpwr & 0xFF;
1595 		(*channel++).hw_value = txpwr >> 8;
1596 	}
1597 	/* Handle the differing rfkill GPIO bit in different models */
1598 	priv->rfkill_mask = RFKILL_MASK_8187_89_97;
1599 	if (product_id == 0x8197 || product_id == 0x8198) {
1600 		eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_SELECT_GPIO, &reg);
1601 		if (reg & 0xFF00)
1602 			priv->rfkill_mask = RFKILL_MASK_8198;
1603 	}
1604 	dev->vif_data_size = sizeof(struct rtl8187_vif);
1605 	dev->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION) |
1606 				      BIT(NL80211_IFTYPE_ADHOC) ;
1607 
1608 	wiphy_ext_feature_set(dev->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
1609 
1610 	if ((id->driver_info == DEVICE_RTL8187) && priv->is_rtl8187b)
1611 		printk(KERN_INFO "rtl8187: inconsistency between id with OEM"
1612 		       " info!\n");
1613 
1614 	priv->rf = rtl8187_detect_rf(dev);
1615 	dev->extra_tx_headroom = (!priv->is_rtl8187b) ?
1616 				  sizeof(struct rtl8187_tx_hdr) :
1617 				  sizeof(struct rtl8187b_tx_hdr);
1618 	if (!priv->is_rtl8187b)
1619 		dev->queues = 1;
1620 	else
1621 		dev->queues = 4;
1622 
1623 	err = ieee80211_register_hw(dev);
1624 	if (err) {
1625 		printk(KERN_ERR "rtl8187: Cannot register device\n");
1626 		goto err_free_dmabuf;
1627 	}
1628 	mutex_init(&priv->conf_mutex);
1629 	skb_queue_head_init(&priv->b_tx_status.queue);
1630 
1631 	wiphy_info(dev->wiphy, "hwaddr %pM, %s V%d + %s, rfkill mask %d\n",
1632 		   mac_addr, chip_name, priv->asic_rev, priv->rf->name,
1633 		   priv->rfkill_mask);
1634 
1635 #ifdef CONFIG_RTL8187_LEDS
1636 	eeprom_93cx6_read(&eeprom, 0x3F, &reg);
1637 	reg &= 0xFF;
1638 	rtl8187_leds_init(dev, reg);
1639 #endif
1640 	rtl8187_rfkill_init(dev);
1641 
1642 	return 0;
1643 
1644  err_free_dmabuf:
1645 	kfree(priv->io_dmabuf);
1646 	usb_set_intfdata(intf, NULL);
1647 	usb_put_dev(udev);
1648  err_free_dev:
1649 	ieee80211_free_hw(dev);
1650 	return err;
1651 }
1652 
1653 static void rtl8187_disconnect(struct usb_interface *intf)
1654 {
1655 	struct ieee80211_hw *dev = usb_get_intfdata(intf);
1656 	struct rtl8187_priv *priv;
1657 
1658 	if (!dev)
1659 		return;
1660 
1661 #ifdef CONFIG_RTL8187_LEDS
1662 	rtl8187_leds_exit(dev);
1663 #endif
1664 	rtl8187_rfkill_exit(dev);
1665 	ieee80211_unregister_hw(dev);
1666 
1667 	priv = dev->priv;
1668 	usb_reset_device(priv->udev);
1669 	usb_put_dev(interface_to_usbdev(intf));
1670 	kfree(priv->io_dmabuf);
1671 	ieee80211_free_hw(dev);
1672 }
1673 
1674 static struct usb_driver rtl8187_driver = {
1675 	.name		= KBUILD_MODNAME,
1676 	.id_table	= rtl8187_table,
1677 	.probe		= rtl8187_probe,
1678 	.disconnect	= rtl8187_disconnect,
1679 	.disable_hub_initiated_lpm = 1,
1680 };
1681 
1682 module_usb_driver(rtl8187_driver);
1683