1 /* 2 * Linux device driver for RTL8187 3 * 4 * Copyright 2007 Michael Wu <flamingice@sourmilk.net> 5 * Copyright 2007 Andrea Merello <andrea.merello@gmail.com> 6 * 7 * Based on the r8187 driver, which is: 8 * Copyright 2005 Andrea Merello <andrea.merello@gmail.com>, et al. 9 * 10 * The driver was extended to the RTL8187B in 2008 by: 11 * Herton Ronaldo Krzesinski <herton@mandriva.com.br> 12 * Hin-Tak Leung <htl10@users.sourceforge.net> 13 * Larry Finger <Larry.Finger@lwfinger.net> 14 * 15 * Magic delays and register offsets below are taken from the original 16 * r8187 driver sources. Thanks to Realtek for their support! 17 * 18 * This program is free software; you can redistribute it and/or modify 19 * it under the terms of the GNU General Public License version 2 as 20 * published by the Free Software Foundation. 21 */ 22 23 #include <linux/usb.h> 24 #include <linux/slab.h> 25 #include <linux/delay.h> 26 #include <linux/etherdevice.h> 27 #include <linux/eeprom_93cx6.h> 28 #include <linux/module.h> 29 #include <net/mac80211.h> 30 31 #include "rtl8187.h" 32 #include "rtl8225.h" 33 #ifdef CONFIG_RTL8187_LEDS 34 #include "leds.h" 35 #endif 36 #include "rfkill.h" 37 38 MODULE_AUTHOR("Michael Wu <flamingice@sourmilk.net>"); 39 MODULE_AUTHOR("Andrea Merello <andrea.merello@gmail.com>"); 40 MODULE_AUTHOR("Herton Ronaldo Krzesinski <herton@mandriva.com.br>"); 41 MODULE_AUTHOR("Hin-Tak Leung <htl10@users.sourceforge.net>"); 42 MODULE_AUTHOR("Larry Finger <Larry.Finger@lwfinger.net>"); 43 MODULE_DESCRIPTION("RTL8187/RTL8187B USB wireless driver"); 44 MODULE_LICENSE("GPL"); 45 46 static struct usb_device_id rtl8187_table[] = { 47 /* Asus */ 48 {USB_DEVICE(0x0b05, 0x171d), .driver_info = DEVICE_RTL8187}, 49 /* Belkin */ 50 {USB_DEVICE(0x050d, 0x705e), .driver_info = DEVICE_RTL8187B}, 51 /* Realtek */ 52 {USB_DEVICE(0x0bda, 0x8187), .driver_info = DEVICE_RTL8187}, 53 {USB_DEVICE(0x0bda, 0x8189), .driver_info = DEVICE_RTL8187B}, 54 {USB_DEVICE(0x0bda, 0x8197), .driver_info = DEVICE_RTL8187B}, 55 {USB_DEVICE(0x0bda, 0x8198), .driver_info = DEVICE_RTL8187B}, 56 /* Surecom */ 57 {USB_DEVICE(0x0769, 0x11F2), .driver_info = DEVICE_RTL8187}, 58 /* Logitech */ 59 {USB_DEVICE(0x0789, 0x010C), .driver_info = DEVICE_RTL8187}, 60 /* Netgear */ 61 {USB_DEVICE(0x0846, 0x6100), .driver_info = DEVICE_RTL8187}, 62 {USB_DEVICE(0x0846, 0x6a00), .driver_info = DEVICE_RTL8187}, 63 {USB_DEVICE(0x0846, 0x4260), .driver_info = DEVICE_RTL8187B}, 64 /* HP */ 65 {USB_DEVICE(0x03f0, 0xca02), .driver_info = DEVICE_RTL8187}, 66 /* Sitecom */ 67 {USB_DEVICE(0x0df6, 0x000d), .driver_info = DEVICE_RTL8187}, 68 {USB_DEVICE(0x0df6, 0x0028), .driver_info = DEVICE_RTL8187B}, 69 {USB_DEVICE(0x0df6, 0x0029), .driver_info = DEVICE_RTL8187B}, 70 /* Sphairon Access Systems GmbH */ 71 {USB_DEVICE(0x114B, 0x0150), .driver_info = DEVICE_RTL8187}, 72 /* Dick Smith Electronics */ 73 {USB_DEVICE(0x1371, 0x9401), .driver_info = DEVICE_RTL8187}, 74 /* Abocom */ 75 {USB_DEVICE(0x13d1, 0xabe6), .driver_info = DEVICE_RTL8187}, 76 /* Qcom */ 77 {USB_DEVICE(0x18E8, 0x6232), .driver_info = DEVICE_RTL8187}, 78 /* AirLive */ 79 {USB_DEVICE(0x1b75, 0x8187), .driver_info = DEVICE_RTL8187}, 80 /* Linksys */ 81 {USB_DEVICE(0x1737, 0x0073), .driver_info = DEVICE_RTL8187B}, 82 {} 83 }; 84 85 MODULE_DEVICE_TABLE(usb, rtl8187_table); 86 87 static const struct ieee80211_rate rtl818x_rates[] = { 88 { .bitrate = 10, .hw_value = 0, }, 89 { .bitrate = 20, .hw_value = 1, }, 90 { .bitrate = 55, .hw_value = 2, }, 91 { .bitrate = 110, .hw_value = 3, }, 92 { .bitrate = 60, .hw_value = 4, }, 93 { .bitrate = 90, .hw_value = 5, }, 94 { .bitrate = 120, .hw_value = 6, }, 95 { .bitrate = 180, .hw_value = 7, }, 96 { .bitrate = 240, .hw_value = 8, }, 97 { .bitrate = 360, .hw_value = 9, }, 98 { .bitrate = 480, .hw_value = 10, }, 99 { .bitrate = 540, .hw_value = 11, }, 100 }; 101 102 static const struct ieee80211_channel rtl818x_channels[] = { 103 { .center_freq = 2412 }, 104 { .center_freq = 2417 }, 105 { .center_freq = 2422 }, 106 { .center_freq = 2427 }, 107 { .center_freq = 2432 }, 108 { .center_freq = 2437 }, 109 { .center_freq = 2442 }, 110 { .center_freq = 2447 }, 111 { .center_freq = 2452 }, 112 { .center_freq = 2457 }, 113 { .center_freq = 2462 }, 114 { .center_freq = 2467 }, 115 { .center_freq = 2472 }, 116 { .center_freq = 2484 }, 117 }; 118 119 static void rtl8187_iowrite_async_cb(struct urb *urb) 120 { 121 kfree(urb->context); 122 } 123 124 static void rtl8187_iowrite_async(struct rtl8187_priv *priv, __le16 addr, 125 void *data, u16 len) 126 { 127 struct usb_ctrlrequest *dr; 128 struct urb *urb; 129 struct rtl8187_async_write_data { 130 u8 data[4]; 131 struct usb_ctrlrequest dr; 132 } *buf; 133 int rc; 134 135 buf = kmalloc(sizeof(*buf), GFP_ATOMIC); 136 if (!buf) 137 return; 138 139 urb = usb_alloc_urb(0, GFP_ATOMIC); 140 if (!urb) { 141 kfree(buf); 142 return; 143 } 144 145 dr = &buf->dr; 146 147 dr->bRequestType = RTL8187_REQT_WRITE; 148 dr->bRequest = RTL8187_REQ_SET_REG; 149 dr->wValue = addr; 150 dr->wIndex = 0; 151 dr->wLength = cpu_to_le16(len); 152 153 memcpy(buf, data, len); 154 155 usb_fill_control_urb(urb, priv->udev, usb_sndctrlpipe(priv->udev, 0), 156 (unsigned char *)dr, buf, len, 157 rtl8187_iowrite_async_cb, buf); 158 usb_anchor_urb(urb, &priv->anchored); 159 rc = usb_submit_urb(urb, GFP_ATOMIC); 160 if (rc < 0) { 161 kfree(buf); 162 usb_unanchor_urb(urb); 163 } 164 usb_free_urb(urb); 165 } 166 167 static inline void rtl818x_iowrite32_async(struct rtl8187_priv *priv, 168 __le32 *addr, u32 val) 169 { 170 __le32 buf = cpu_to_le32(val); 171 172 rtl8187_iowrite_async(priv, cpu_to_le16((unsigned long)addr), 173 &buf, sizeof(buf)); 174 } 175 176 void rtl8187_write_phy(struct ieee80211_hw *dev, u8 addr, u32 data) 177 { 178 struct rtl8187_priv *priv = dev->priv; 179 180 data <<= 8; 181 data |= addr | 0x80; 182 183 rtl818x_iowrite8(priv, &priv->map->PHY[3], (data >> 24) & 0xFF); 184 rtl818x_iowrite8(priv, &priv->map->PHY[2], (data >> 16) & 0xFF); 185 rtl818x_iowrite8(priv, &priv->map->PHY[1], (data >> 8) & 0xFF); 186 rtl818x_iowrite8(priv, &priv->map->PHY[0], data & 0xFF); 187 } 188 189 static void rtl8187_tx_cb(struct urb *urb) 190 { 191 struct sk_buff *skb = (struct sk_buff *)urb->context; 192 struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); 193 struct ieee80211_hw *hw = info->rate_driver_data[0]; 194 struct rtl8187_priv *priv = hw->priv; 195 196 skb_pull(skb, priv->is_rtl8187b ? sizeof(struct rtl8187b_tx_hdr) : 197 sizeof(struct rtl8187_tx_hdr)); 198 ieee80211_tx_info_clear_status(info); 199 200 if (!(urb->status) && !(info->flags & IEEE80211_TX_CTL_NO_ACK)) { 201 if (priv->is_rtl8187b) { 202 skb_queue_tail(&priv->b_tx_status.queue, skb); 203 204 /* queue is "full", discard last items */ 205 while (skb_queue_len(&priv->b_tx_status.queue) > 5) { 206 struct sk_buff *old_skb; 207 208 dev_dbg(&priv->udev->dev, 209 "transmit status queue full\n"); 210 211 old_skb = skb_dequeue(&priv->b_tx_status.queue); 212 ieee80211_tx_status_irqsafe(hw, old_skb); 213 } 214 return; 215 } else { 216 info->flags |= IEEE80211_TX_STAT_ACK; 217 } 218 } 219 if (priv->is_rtl8187b) 220 ieee80211_tx_status_irqsafe(hw, skb); 221 else { 222 /* Retry information for the RTI8187 is only available by 223 * reading a register in the device. We are in interrupt mode 224 * here, thus queue the skb and finish on a work queue. */ 225 skb_queue_tail(&priv->b_tx_status.queue, skb); 226 ieee80211_queue_delayed_work(hw, &priv->work, 0); 227 } 228 } 229 230 static void rtl8187_tx(struct ieee80211_hw *dev, 231 struct ieee80211_tx_control *control, 232 struct sk_buff *skb) 233 { 234 struct rtl8187_priv *priv = dev->priv; 235 struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); 236 struct ieee80211_hdr *tx_hdr = (struct ieee80211_hdr *)(skb->data); 237 unsigned int ep; 238 void *buf; 239 struct urb *urb; 240 __le16 rts_dur = 0; 241 u32 flags; 242 int rc; 243 244 urb = usb_alloc_urb(0, GFP_ATOMIC); 245 if (!urb) { 246 kfree_skb(skb); 247 return; 248 } 249 250 flags = skb->len; 251 flags |= RTL818X_TX_DESC_FLAG_NO_ENC; 252 253 flags |= ieee80211_get_tx_rate(dev, info)->hw_value << 24; 254 if (ieee80211_has_morefrags(tx_hdr->frame_control)) 255 flags |= RTL818X_TX_DESC_FLAG_MOREFRAG; 256 257 /* HW will perform RTS-CTS when only RTS flags is set. 258 * HW will perform CTS-to-self when both RTS and CTS flags are set. 259 * RTS rate and RTS duration will be used also for CTS-to-self. 260 */ 261 if (info->control.rates[0].flags & IEEE80211_TX_RC_USE_RTS_CTS) { 262 flags |= RTL818X_TX_DESC_FLAG_RTS; 263 flags |= ieee80211_get_rts_cts_rate(dev, info)->hw_value << 19; 264 rts_dur = ieee80211_rts_duration(dev, priv->vif, 265 skb->len, info); 266 } else if (info->control.rates[0].flags & IEEE80211_TX_RC_USE_CTS_PROTECT) { 267 flags |= RTL818X_TX_DESC_FLAG_RTS | RTL818X_TX_DESC_FLAG_CTS; 268 flags |= ieee80211_get_rts_cts_rate(dev, info)->hw_value << 19; 269 rts_dur = ieee80211_ctstoself_duration(dev, priv->vif, 270 skb->len, info); 271 } 272 273 if (info->flags & IEEE80211_TX_CTL_ASSIGN_SEQ) { 274 if (info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT) 275 priv->seqno += 0x10; 276 tx_hdr->seq_ctrl &= cpu_to_le16(IEEE80211_SCTL_FRAG); 277 tx_hdr->seq_ctrl |= cpu_to_le16(priv->seqno); 278 } 279 280 if (!priv->is_rtl8187b) { 281 struct rtl8187_tx_hdr *hdr = 282 (struct rtl8187_tx_hdr *)skb_push(skb, sizeof(*hdr)); 283 hdr->flags = cpu_to_le32(flags); 284 hdr->len = 0; 285 hdr->rts_duration = rts_dur; 286 hdr->retry = cpu_to_le32((info->control.rates[0].count - 1) << 8); 287 buf = hdr; 288 289 ep = 2; 290 } else { 291 /* fc needs to be calculated before skb_push() */ 292 unsigned int epmap[4] = { 6, 7, 5, 4 }; 293 u16 fc = le16_to_cpu(tx_hdr->frame_control); 294 295 struct rtl8187b_tx_hdr *hdr = 296 (struct rtl8187b_tx_hdr *)skb_push(skb, sizeof(*hdr)); 297 struct ieee80211_rate *txrate = 298 ieee80211_get_tx_rate(dev, info); 299 memset(hdr, 0, sizeof(*hdr)); 300 hdr->flags = cpu_to_le32(flags); 301 hdr->rts_duration = rts_dur; 302 hdr->retry = cpu_to_le32((info->control.rates[0].count - 1) << 8); 303 hdr->tx_duration = 304 ieee80211_generic_frame_duration(dev, priv->vif, 305 info->band, 306 skb->len, txrate); 307 buf = hdr; 308 309 if ((fc & IEEE80211_FCTL_FTYPE) == IEEE80211_FTYPE_MGMT) 310 ep = 12; 311 else 312 ep = epmap[skb_get_queue_mapping(skb)]; 313 } 314 315 info->rate_driver_data[0] = dev; 316 info->rate_driver_data[1] = urb; 317 318 usb_fill_bulk_urb(urb, priv->udev, usb_sndbulkpipe(priv->udev, ep), 319 buf, skb->len, rtl8187_tx_cb, skb); 320 urb->transfer_flags |= URB_ZERO_PACKET; 321 usb_anchor_urb(urb, &priv->anchored); 322 rc = usb_submit_urb(urb, GFP_ATOMIC); 323 if (rc < 0) { 324 usb_unanchor_urb(urb); 325 kfree_skb(skb); 326 } 327 usb_free_urb(urb); 328 } 329 330 static void rtl8187_rx_cb(struct urb *urb) 331 { 332 struct sk_buff *skb = (struct sk_buff *)urb->context; 333 struct rtl8187_rx_info *info = (struct rtl8187_rx_info *)skb->cb; 334 struct ieee80211_hw *dev = info->dev; 335 struct rtl8187_priv *priv = dev->priv; 336 struct ieee80211_rx_status rx_status = { 0 }; 337 int rate, signal; 338 u32 flags; 339 unsigned long f; 340 341 spin_lock_irqsave(&priv->rx_queue.lock, f); 342 __skb_unlink(skb, &priv->rx_queue); 343 spin_unlock_irqrestore(&priv->rx_queue.lock, f); 344 skb_put(skb, urb->actual_length); 345 346 if (unlikely(urb->status)) { 347 dev_kfree_skb_irq(skb); 348 return; 349 } 350 351 if (!priv->is_rtl8187b) { 352 struct rtl8187_rx_hdr *hdr = 353 (typeof(hdr))(skb_tail_pointer(skb) - sizeof(*hdr)); 354 flags = le32_to_cpu(hdr->flags); 355 /* As with the RTL8187B below, the AGC is used to calculate 356 * signal strength. In this case, the scaling 357 * constants are derived from the output of p54usb. 358 */ 359 signal = -4 - ((27 * hdr->agc) >> 6); 360 rx_status.antenna = (hdr->signal >> 7) & 1; 361 rx_status.mactime = le64_to_cpu(hdr->mac_time); 362 } else { 363 struct rtl8187b_rx_hdr *hdr = 364 (typeof(hdr))(skb_tail_pointer(skb) - sizeof(*hdr)); 365 /* The Realtek datasheet for the RTL8187B shows that the RX 366 * header contains the following quantities: signal quality, 367 * RSSI, AGC, the received power in dB, and the measured SNR. 368 * In testing, none of these quantities show qualitative 369 * agreement with AP signal strength, except for the AGC, 370 * which is inversely proportional to the strength of the 371 * signal. In the following, the signal strength 372 * is derived from the AGC. The arbitrary scaling constants 373 * are chosen to make the results close to the values obtained 374 * for a BCM4312 using b43 as the driver. The noise is ignored 375 * for now. 376 */ 377 flags = le32_to_cpu(hdr->flags); 378 signal = 14 - hdr->agc / 2; 379 rx_status.antenna = (hdr->rssi >> 7) & 1; 380 rx_status.mactime = le64_to_cpu(hdr->mac_time); 381 } 382 383 rx_status.signal = signal; 384 priv->signal = signal; 385 rate = (flags >> 20) & 0xF; 386 skb_trim(skb, flags & 0x0FFF); 387 rx_status.rate_idx = rate; 388 rx_status.freq = dev->conf.chandef.chan->center_freq; 389 rx_status.band = dev->conf.chandef.chan->band; 390 rx_status.flag |= RX_FLAG_MACTIME_START; 391 if (flags & RTL818X_RX_DESC_FLAG_SPLCP) 392 rx_status.enc_flags |= RX_ENC_FLAG_SHORTPRE; 393 if (flags & RTL818X_RX_DESC_FLAG_CRC32_ERR) 394 rx_status.flag |= RX_FLAG_FAILED_FCS_CRC; 395 memcpy(IEEE80211_SKB_RXCB(skb), &rx_status, sizeof(rx_status)); 396 ieee80211_rx_irqsafe(dev, skb); 397 398 skb = dev_alloc_skb(RTL8187_MAX_RX); 399 if (unlikely(!skb)) { 400 /* TODO check rx queue length and refill *somewhere* */ 401 return; 402 } 403 404 info = (struct rtl8187_rx_info *)skb->cb; 405 info->urb = urb; 406 info->dev = dev; 407 urb->transfer_buffer = skb_tail_pointer(skb); 408 urb->context = skb; 409 skb_queue_tail(&priv->rx_queue, skb); 410 411 usb_anchor_urb(urb, &priv->anchored); 412 if (usb_submit_urb(urb, GFP_ATOMIC)) { 413 usb_unanchor_urb(urb); 414 skb_unlink(skb, &priv->rx_queue); 415 dev_kfree_skb_irq(skb); 416 } 417 } 418 419 static int rtl8187_init_urbs(struct ieee80211_hw *dev) 420 { 421 struct rtl8187_priv *priv = dev->priv; 422 struct urb *entry = NULL; 423 struct sk_buff *skb; 424 struct rtl8187_rx_info *info; 425 int ret = 0; 426 427 while (skb_queue_len(&priv->rx_queue) < 32) { 428 skb = __dev_alloc_skb(RTL8187_MAX_RX, GFP_KERNEL); 429 if (!skb) { 430 ret = -ENOMEM; 431 goto err; 432 } 433 entry = usb_alloc_urb(0, GFP_KERNEL); 434 if (!entry) { 435 ret = -ENOMEM; 436 goto err; 437 } 438 usb_fill_bulk_urb(entry, priv->udev, 439 usb_rcvbulkpipe(priv->udev, 440 priv->is_rtl8187b ? 3 : 1), 441 skb_tail_pointer(skb), 442 RTL8187_MAX_RX, rtl8187_rx_cb, skb); 443 info = (struct rtl8187_rx_info *)skb->cb; 444 info->urb = entry; 445 info->dev = dev; 446 skb_queue_tail(&priv->rx_queue, skb); 447 usb_anchor_urb(entry, &priv->anchored); 448 ret = usb_submit_urb(entry, GFP_KERNEL); 449 usb_put_urb(entry); 450 if (ret) { 451 skb_unlink(skb, &priv->rx_queue); 452 usb_unanchor_urb(entry); 453 goto err; 454 } 455 } 456 return ret; 457 458 err: 459 kfree_skb(skb); 460 usb_kill_anchored_urbs(&priv->anchored); 461 return ret; 462 } 463 464 static void rtl8187b_status_cb(struct urb *urb) 465 { 466 struct ieee80211_hw *hw = (struct ieee80211_hw *)urb->context; 467 struct rtl8187_priv *priv = hw->priv; 468 u64 val; 469 unsigned int cmd_type; 470 471 if (unlikely(urb->status)) 472 return; 473 474 /* 475 * Read from status buffer: 476 * 477 * bits [30:31] = cmd type: 478 * - 0 indicates tx beacon interrupt 479 * - 1 indicates tx close descriptor 480 * 481 * In the case of tx beacon interrupt: 482 * [0:9] = Last Beacon CW 483 * [10:29] = reserved 484 * [30:31] = 00b 485 * [32:63] = Last Beacon TSF 486 * 487 * If it's tx close descriptor: 488 * [0:7] = Packet Retry Count 489 * [8:14] = RTS Retry Count 490 * [15] = TOK 491 * [16:27] = Sequence No 492 * [28] = LS 493 * [29] = FS 494 * [30:31] = 01b 495 * [32:47] = unused (reserved?) 496 * [48:63] = MAC Used Time 497 */ 498 val = le64_to_cpu(priv->b_tx_status.buf); 499 500 cmd_type = (val >> 30) & 0x3; 501 if (cmd_type == 1) { 502 unsigned int pkt_rc, seq_no; 503 bool tok; 504 struct sk_buff *skb; 505 struct ieee80211_hdr *ieee80211hdr; 506 unsigned long flags; 507 508 pkt_rc = val & 0xFF; 509 tok = val & (1 << 15); 510 seq_no = (val >> 16) & 0xFFF; 511 512 spin_lock_irqsave(&priv->b_tx_status.queue.lock, flags); 513 skb_queue_reverse_walk(&priv->b_tx_status.queue, skb) { 514 ieee80211hdr = (struct ieee80211_hdr *)skb->data; 515 516 /* 517 * While testing, it was discovered that the seq_no 518 * doesn't actually contains the sequence number. 519 * Instead of returning just the 12 bits of sequence 520 * number, hardware is returning entire sequence control 521 * (fragment number plus sequence number) in a 12 bit 522 * only field overflowing after some time. As a 523 * workaround, just consider the lower bits, and expect 524 * it's unlikely we wrongly ack some sent data 525 */ 526 if ((le16_to_cpu(ieee80211hdr->seq_ctrl) 527 & 0xFFF) == seq_no) 528 break; 529 } 530 if (skb != (struct sk_buff *) &priv->b_tx_status.queue) { 531 struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); 532 533 __skb_unlink(skb, &priv->b_tx_status.queue); 534 if (tok) 535 info->flags |= IEEE80211_TX_STAT_ACK; 536 info->status.rates[0].count = pkt_rc + 1; 537 538 ieee80211_tx_status_irqsafe(hw, skb); 539 } 540 spin_unlock_irqrestore(&priv->b_tx_status.queue.lock, flags); 541 } 542 543 usb_anchor_urb(urb, &priv->anchored); 544 if (usb_submit_urb(urb, GFP_ATOMIC)) 545 usb_unanchor_urb(urb); 546 } 547 548 static int rtl8187b_init_status_urb(struct ieee80211_hw *dev) 549 { 550 struct rtl8187_priv *priv = dev->priv; 551 struct urb *entry; 552 int ret = 0; 553 554 entry = usb_alloc_urb(0, GFP_KERNEL); 555 if (!entry) 556 return -ENOMEM; 557 558 usb_fill_bulk_urb(entry, priv->udev, usb_rcvbulkpipe(priv->udev, 9), 559 &priv->b_tx_status.buf, sizeof(priv->b_tx_status.buf), 560 rtl8187b_status_cb, dev); 561 562 usb_anchor_urb(entry, &priv->anchored); 563 ret = usb_submit_urb(entry, GFP_KERNEL); 564 if (ret) 565 usb_unanchor_urb(entry); 566 usb_free_urb(entry); 567 568 return ret; 569 } 570 571 static void rtl8187_set_anaparam(struct rtl8187_priv *priv, bool rfon) 572 { 573 u32 anaparam, anaparam2; 574 u8 anaparam3, reg; 575 576 if (!priv->is_rtl8187b) { 577 if (rfon) { 578 anaparam = RTL8187_RTL8225_ANAPARAM_ON; 579 anaparam2 = RTL8187_RTL8225_ANAPARAM2_ON; 580 } else { 581 anaparam = RTL8187_RTL8225_ANAPARAM_OFF; 582 anaparam2 = RTL8187_RTL8225_ANAPARAM2_OFF; 583 } 584 } else { 585 if (rfon) { 586 anaparam = RTL8187B_RTL8225_ANAPARAM_ON; 587 anaparam2 = RTL8187B_RTL8225_ANAPARAM2_ON; 588 anaparam3 = RTL8187B_RTL8225_ANAPARAM3_ON; 589 } else { 590 anaparam = RTL8187B_RTL8225_ANAPARAM_OFF; 591 anaparam2 = RTL8187B_RTL8225_ANAPARAM2_OFF; 592 anaparam3 = RTL8187B_RTL8225_ANAPARAM3_OFF; 593 } 594 } 595 596 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, 597 RTL818X_EEPROM_CMD_CONFIG); 598 reg = rtl818x_ioread8(priv, &priv->map->CONFIG3); 599 reg |= RTL818X_CONFIG3_ANAPARAM_WRITE; 600 rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg); 601 rtl818x_iowrite32(priv, &priv->map->ANAPARAM, anaparam); 602 rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, anaparam2); 603 if (priv->is_rtl8187b) 604 rtl818x_iowrite8(priv, &priv->map->ANAPARAM3A, anaparam3); 605 reg &= ~RTL818X_CONFIG3_ANAPARAM_WRITE; 606 rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg); 607 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, 608 RTL818X_EEPROM_CMD_NORMAL); 609 } 610 611 static int rtl8187_cmd_reset(struct ieee80211_hw *dev) 612 { 613 struct rtl8187_priv *priv = dev->priv; 614 u8 reg; 615 int i; 616 617 reg = rtl818x_ioread8(priv, &priv->map->CMD); 618 reg &= (1 << 1); 619 reg |= RTL818X_CMD_RESET; 620 rtl818x_iowrite8(priv, &priv->map->CMD, reg); 621 622 i = 10; 623 do { 624 msleep(2); 625 if (!(rtl818x_ioread8(priv, &priv->map->CMD) & 626 RTL818X_CMD_RESET)) 627 break; 628 } while (--i); 629 630 if (!i) { 631 wiphy_err(dev->wiphy, "Reset timeout!\n"); 632 return -ETIMEDOUT; 633 } 634 635 /* reload registers from eeprom */ 636 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_LOAD); 637 638 i = 10; 639 do { 640 msleep(4); 641 if (!(rtl818x_ioread8(priv, &priv->map->EEPROM_CMD) & 642 RTL818X_EEPROM_CMD_CONFIG)) 643 break; 644 } while (--i); 645 646 if (!i) { 647 wiphy_err(dev->wiphy, "eeprom reset timeout!\n"); 648 return -ETIMEDOUT; 649 } 650 651 return 0; 652 } 653 654 static int rtl8187_init_hw(struct ieee80211_hw *dev) 655 { 656 struct rtl8187_priv *priv = dev->priv; 657 u8 reg; 658 int res; 659 660 /* reset */ 661 rtl8187_set_anaparam(priv, true); 662 663 rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0); 664 665 msleep(200); 666 rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x10); 667 rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x11); 668 rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x00); 669 msleep(200); 670 671 res = rtl8187_cmd_reset(dev); 672 if (res) 673 return res; 674 675 rtl8187_set_anaparam(priv, true); 676 677 /* setup card */ 678 rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0); 679 rtl818x_iowrite8(priv, &priv->map->GPIO0, 0); 680 681 rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, (4 << 8)); 682 rtl818x_iowrite8(priv, &priv->map->GPIO0, 1); 683 rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0); 684 685 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); 686 687 rtl818x_iowrite16(priv, (__le16 *)0xFFF4, 0xFFFF); 688 reg = rtl818x_ioread8(priv, &priv->map->CONFIG1); 689 reg &= 0x3F; 690 reg |= 0x80; 691 rtl818x_iowrite8(priv, &priv->map->CONFIG1, reg); 692 693 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); 694 695 rtl818x_iowrite32(priv, &priv->map->INT_TIMEOUT, 0); 696 rtl818x_iowrite8(priv, &priv->map->WPA_CONF, 0); 697 rtl818x_iowrite8(priv, &priv->map->RATE_FALLBACK, 0); 698 699 // TODO: set RESP_RATE and BRSR properly 700 rtl818x_iowrite8(priv, &priv->map->RESP_RATE, (8 << 4) | 0); 701 rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3); 702 703 /* host_usb_init */ 704 rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0); 705 rtl818x_iowrite8(priv, &priv->map->GPIO0, 0); 706 reg = rtl818x_ioread8(priv, (u8 *)0xFE53); 707 rtl818x_iowrite8(priv, (u8 *)0xFE53, reg | (1 << 7)); 708 rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, (4 << 8)); 709 rtl818x_iowrite8(priv, &priv->map->GPIO0, 0x20); 710 rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0); 711 rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, 0x80); 712 rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0x80); 713 rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x80); 714 msleep(100); 715 716 rtl818x_iowrite32(priv, &priv->map->RF_TIMING, 0x000a8008); 717 rtl818x_iowrite16(priv, &priv->map->BRSR, 0xFFFF); 718 rtl818x_iowrite32(priv, &priv->map->RF_PARA, 0x00100044); 719 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, 720 RTL818X_EEPROM_CMD_CONFIG); 721 rtl818x_iowrite8(priv, &priv->map->CONFIG3, 0x44); 722 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, 723 RTL818X_EEPROM_CMD_NORMAL); 724 rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FF7); 725 msleep(100); 726 727 priv->rf->init(dev); 728 729 rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3); 730 reg = rtl818x_ioread8(priv, &priv->map->PGSELECT) & ~1; 731 rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg | 1); 732 rtl818x_iowrite16(priv, (__le16 *)0xFFFE, 0x10); 733 rtl818x_iowrite8(priv, &priv->map->TALLY_SEL, 0x80); 734 rtl818x_iowrite8(priv, (u8 *)0xFFFF, 0x60); 735 rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg); 736 737 return 0; 738 } 739 740 static const u8 rtl8187b_reg_table[][3] = { 741 {0xF0, 0x32, 0}, {0xF1, 0x32, 0}, {0xF2, 0x00, 0}, {0xF3, 0x00, 0}, 742 {0xF4, 0x32, 0}, {0xF5, 0x43, 0}, {0xF6, 0x00, 0}, {0xF7, 0x00, 0}, 743 {0xF8, 0x46, 0}, {0xF9, 0xA4, 0}, {0xFA, 0x00, 0}, {0xFB, 0x00, 0}, 744 {0xFC, 0x96, 0}, {0xFD, 0xA4, 0}, {0xFE, 0x00, 0}, {0xFF, 0x00, 0}, 745 746 {0x58, 0x4B, 1}, {0x59, 0x00, 1}, {0x5A, 0x4B, 1}, {0x5B, 0x00, 1}, 747 {0x60, 0x4B, 1}, {0x61, 0x09, 1}, {0x62, 0x4B, 1}, {0x63, 0x09, 1}, 748 {0xCE, 0x0F, 1}, {0xCF, 0x00, 1}, {0xF0, 0x4E, 1}, {0xF1, 0x01, 1}, 749 {0xF2, 0x02, 1}, {0xF3, 0x03, 1}, {0xF4, 0x04, 1}, {0xF5, 0x05, 1}, 750 {0xF6, 0x06, 1}, {0xF7, 0x07, 1}, {0xF8, 0x08, 1}, 751 752 {0x4E, 0x00, 2}, {0x0C, 0x04, 2}, {0x21, 0x61, 2}, {0x22, 0x68, 2}, 753 {0x23, 0x6F, 2}, {0x24, 0x76, 2}, {0x25, 0x7D, 2}, {0x26, 0x84, 2}, 754 {0x27, 0x8D, 2}, {0x4D, 0x08, 2}, {0x50, 0x05, 2}, {0x51, 0xF5, 2}, 755 {0x52, 0x04, 2}, {0x53, 0xA0, 2}, {0x54, 0x1F, 2}, {0x55, 0x23, 2}, 756 {0x56, 0x45, 2}, {0x57, 0x67, 2}, {0x58, 0x08, 2}, {0x59, 0x08, 2}, 757 {0x5A, 0x08, 2}, {0x5B, 0x08, 2}, {0x60, 0x08, 2}, {0x61, 0x08, 2}, 758 {0x62, 0x08, 2}, {0x63, 0x08, 2}, {0x64, 0xCF, 2}, 759 760 {0x5B, 0x40, 0}, {0x84, 0x88, 0}, {0x85, 0x24, 0}, {0x88, 0x54, 0}, 761 {0x8B, 0xB8, 0}, {0x8C, 0x07, 0}, {0x8D, 0x00, 0}, {0x94, 0x1B, 0}, 762 {0x95, 0x12, 0}, {0x96, 0x00, 0}, {0x97, 0x06, 0}, {0x9D, 0x1A, 0}, 763 {0x9F, 0x10, 0}, {0xB4, 0x22, 0}, {0xBE, 0x80, 0}, {0xDB, 0x00, 0}, 764 {0xEE, 0x00, 0}, {0x4C, 0x00, 2}, 765 766 {0x9F, 0x00, 3}, {0x8C, 0x01, 0}, {0x8D, 0x10, 0}, {0x8E, 0x08, 0}, 767 {0x8F, 0x00, 0} 768 }; 769 770 static int rtl8187b_init_hw(struct ieee80211_hw *dev) 771 { 772 struct rtl8187_priv *priv = dev->priv; 773 int res, i; 774 u8 reg; 775 776 rtl8187_set_anaparam(priv, true); 777 778 /* Reset PLL sequence on 8187B. Realtek note: reduces power 779 * consumption about 30 mA */ 780 rtl818x_iowrite8(priv, (u8 *)0xFF61, 0x10); 781 reg = rtl818x_ioread8(priv, (u8 *)0xFF62); 782 rtl818x_iowrite8(priv, (u8 *)0xFF62, reg & ~(1 << 5)); 783 rtl818x_iowrite8(priv, (u8 *)0xFF62, reg | (1 << 5)); 784 785 res = rtl8187_cmd_reset(dev); 786 if (res) 787 return res; 788 789 rtl8187_set_anaparam(priv, true); 790 791 /* BRSR (Basic Rate Set Register) on 8187B looks to be the same as 792 * RESP_RATE on 8187L in Realtek sources: each bit should be each 793 * one of the 12 rates, all are enabled */ 794 rtl818x_iowrite16(priv, (__le16 *)0xFF34, 0x0FFF); 795 796 reg = rtl818x_ioread8(priv, &priv->map->CW_CONF); 797 reg |= RTL818X_CW_CONF_PERPACKET_RETRY; 798 rtl818x_iowrite8(priv, &priv->map->CW_CONF, reg); 799 800 /* Auto Rate Fallback Register (ARFR): 1M-54M setting */ 801 rtl818x_iowrite16_idx(priv, (__le16 *)0xFFE0, 0x0FFF, 1); 802 rtl818x_iowrite8_idx(priv, (u8 *)0xFFE2, 0x00, 1); 803 804 rtl818x_iowrite16_idx(priv, (__le16 *)0xFFD4, 0xFFFF, 1); 805 806 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, 807 RTL818X_EEPROM_CMD_CONFIG); 808 reg = rtl818x_ioread8(priv, &priv->map->CONFIG1); 809 rtl818x_iowrite8(priv, &priv->map->CONFIG1, (reg & 0x3F) | 0x80); 810 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, 811 RTL818X_EEPROM_CMD_NORMAL); 812 813 rtl818x_iowrite8(priv, &priv->map->WPA_CONF, 0); 814 for (i = 0; i < ARRAY_SIZE(rtl8187b_reg_table); i++) { 815 rtl818x_iowrite8_idx(priv, 816 (u8 *)(uintptr_t) 817 (rtl8187b_reg_table[i][0] | 0xFF00), 818 rtl8187b_reg_table[i][1], 819 rtl8187b_reg_table[i][2]); 820 } 821 822 rtl818x_iowrite16(priv, &priv->map->TID_AC_MAP, 0xFA50); 823 rtl818x_iowrite16(priv, &priv->map->INT_MIG, 0); 824 825 rtl818x_iowrite32_idx(priv, (__le32 *)0xFFF0, 0, 1); 826 rtl818x_iowrite32_idx(priv, (__le32 *)0xFFF4, 0, 1); 827 rtl818x_iowrite8_idx(priv, (u8 *)0xFFF8, 0, 1); 828 829 rtl818x_iowrite32(priv, &priv->map->RF_TIMING, 0x00004001); 830 831 /* RFSW_CTRL register */ 832 rtl818x_iowrite16_idx(priv, (__le16 *)0xFF72, 0x569A, 2); 833 834 rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, 0x0480); 835 rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0x2488); 836 rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FFF); 837 msleep(100); 838 839 priv->rf->init(dev); 840 841 reg = RTL818X_CMD_TX_ENABLE | RTL818X_CMD_RX_ENABLE; 842 rtl818x_iowrite8(priv, &priv->map->CMD, reg); 843 rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0xFFFF); 844 845 rtl818x_iowrite8(priv, (u8 *)0xFE41, 0xF4); 846 rtl818x_iowrite8(priv, (u8 *)0xFE40, 0x00); 847 rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x00); 848 rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x01); 849 rtl818x_iowrite8(priv, (u8 *)0xFE40, 0x0F); 850 rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x00); 851 rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x01); 852 853 reg = rtl818x_ioread8(priv, (u8 *)0xFFDB); 854 rtl818x_iowrite8(priv, (u8 *)0xFFDB, reg | (1 << 2)); 855 rtl818x_iowrite16_idx(priv, (__le16 *)0xFF72, 0x59FA, 3); 856 rtl818x_iowrite16_idx(priv, (__le16 *)0xFF74, 0x59D2, 3); 857 rtl818x_iowrite16_idx(priv, (__le16 *)0xFF76, 0x59D2, 3); 858 rtl818x_iowrite16_idx(priv, (__le16 *)0xFF78, 0x19FA, 3); 859 rtl818x_iowrite16_idx(priv, (__le16 *)0xFF7A, 0x19FA, 3); 860 rtl818x_iowrite16_idx(priv, (__le16 *)0xFF7C, 0x00D0, 3); 861 rtl818x_iowrite8(priv, (u8 *)0xFF61, 0); 862 rtl818x_iowrite8_idx(priv, (u8 *)0xFF80, 0x0F, 1); 863 rtl818x_iowrite8_idx(priv, (u8 *)0xFF83, 0x03, 1); 864 rtl818x_iowrite8(priv, (u8 *)0xFFDA, 0x10); 865 rtl818x_iowrite8_idx(priv, (u8 *)0xFF4D, 0x08, 2); 866 867 rtl818x_iowrite32(priv, &priv->map->HSSI_PARA, 0x0600321B); 868 869 rtl818x_iowrite16_idx(priv, (__le16 *)0xFFEC, 0x0800, 1); 870 871 priv->slot_time = 0x9; 872 priv->aifsn[0] = 2; /* AIFSN[AC_VO] */ 873 priv->aifsn[1] = 2; /* AIFSN[AC_VI] */ 874 priv->aifsn[2] = 7; /* AIFSN[AC_BK] */ 875 priv->aifsn[3] = 3; /* AIFSN[AC_BE] */ 876 rtl818x_iowrite8(priv, &priv->map->ACM_CONTROL, 0); 877 878 /* ENEDCA flag must always be set, transmit issues? */ 879 rtl818x_iowrite8(priv, &priv->map->MSR, RTL818X_MSR_ENEDCA); 880 881 return 0; 882 } 883 884 static void rtl8187_work(struct work_struct *work) 885 { 886 /* The RTL8187 returns the retry count through register 0xFFFA. In 887 * addition, it appears to be a cumulative retry count, not the 888 * value for the current TX packet. When multiple TX entries are 889 * waiting in the queue, the retry count will be the total for all. 890 * The "error" may matter for purposes of rate setting, but there is 891 * no other choice with this hardware. 892 */ 893 struct rtl8187_priv *priv = container_of(work, struct rtl8187_priv, 894 work.work); 895 struct ieee80211_tx_info *info; 896 struct ieee80211_hw *dev = priv->dev; 897 static u16 retry; 898 u16 tmp; 899 u16 avg_retry; 900 int length; 901 902 mutex_lock(&priv->conf_mutex); 903 tmp = rtl818x_ioread16(priv, (__le16 *)0xFFFA); 904 length = skb_queue_len(&priv->b_tx_status.queue); 905 if (unlikely(!length)) 906 length = 1; 907 if (unlikely(tmp < retry)) 908 tmp = retry; 909 avg_retry = (tmp - retry) / length; 910 while (skb_queue_len(&priv->b_tx_status.queue) > 0) { 911 struct sk_buff *old_skb; 912 913 old_skb = skb_dequeue(&priv->b_tx_status.queue); 914 info = IEEE80211_SKB_CB(old_skb); 915 info->status.rates[0].count = avg_retry + 1; 916 if (info->status.rates[0].count > RETRY_COUNT) 917 info->flags &= ~IEEE80211_TX_STAT_ACK; 918 ieee80211_tx_status_irqsafe(dev, old_skb); 919 } 920 retry = tmp; 921 mutex_unlock(&priv->conf_mutex); 922 } 923 924 static int rtl8187_start(struct ieee80211_hw *dev) 925 { 926 struct rtl8187_priv *priv = dev->priv; 927 u32 reg; 928 int ret; 929 930 mutex_lock(&priv->conf_mutex); 931 932 ret = (!priv->is_rtl8187b) ? rtl8187_init_hw(dev) : 933 rtl8187b_init_hw(dev); 934 if (ret) 935 goto rtl8187_start_exit; 936 937 init_usb_anchor(&priv->anchored); 938 priv->dev = dev; 939 940 if (priv->is_rtl8187b) { 941 reg = RTL818X_RX_CONF_MGMT | 942 RTL818X_RX_CONF_DATA | 943 RTL818X_RX_CONF_BROADCAST | 944 RTL818X_RX_CONF_NICMAC | 945 RTL818X_RX_CONF_BSSID | 946 (7 << 13 /* RX FIFO threshold NONE */) | 947 (7 << 10 /* MAX RX DMA */) | 948 RTL818X_RX_CONF_RX_AUTORESETPHY | 949 RTL818X_RX_CONF_ONLYERLPKT; 950 priv->rx_conf = reg; 951 rtl818x_iowrite32(priv, &priv->map->RX_CONF, reg); 952 953 reg = rtl818x_ioread8(priv, &priv->map->TX_AGC_CTL); 954 reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_GAIN; 955 reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL; 956 reg &= ~RTL818X_TX_AGC_CTL_FEEDBACK_ANT; 957 rtl818x_iowrite8(priv, &priv->map->TX_AGC_CTL, reg); 958 959 rtl818x_iowrite32(priv, &priv->map->TX_CONF, 960 RTL818X_TX_CONF_HW_SEQNUM | 961 RTL818X_TX_CONF_DISREQQSIZE | 962 (RETRY_COUNT << 8 /* short retry limit */) | 963 (RETRY_COUNT << 0 /* long retry limit */) | 964 (7 << 21 /* MAX TX DMA */)); 965 ret = rtl8187_init_urbs(dev); 966 if (ret) 967 goto rtl8187_start_exit; 968 ret = rtl8187b_init_status_urb(dev); 969 if (ret) 970 usb_kill_anchored_urbs(&priv->anchored); 971 goto rtl8187_start_exit; 972 } 973 974 rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0xFFFF); 975 976 rtl818x_iowrite32(priv, &priv->map->MAR[0], ~0); 977 rtl818x_iowrite32(priv, &priv->map->MAR[1], ~0); 978 979 ret = rtl8187_init_urbs(dev); 980 if (ret) 981 goto rtl8187_start_exit; 982 983 reg = RTL818X_RX_CONF_ONLYERLPKT | 984 RTL818X_RX_CONF_RX_AUTORESETPHY | 985 RTL818X_RX_CONF_BSSID | 986 RTL818X_RX_CONF_MGMT | 987 RTL818X_RX_CONF_DATA | 988 (7 << 13 /* RX FIFO threshold NONE */) | 989 (7 << 10 /* MAX RX DMA */) | 990 RTL818X_RX_CONF_BROADCAST | 991 RTL818X_RX_CONF_NICMAC; 992 993 priv->rx_conf = reg; 994 rtl818x_iowrite32(priv, &priv->map->RX_CONF, reg); 995 996 reg = rtl818x_ioread8(priv, &priv->map->CW_CONF); 997 reg &= ~RTL818X_CW_CONF_PERPACKET_CW; 998 reg |= RTL818X_CW_CONF_PERPACKET_RETRY; 999 rtl818x_iowrite8(priv, &priv->map->CW_CONF, reg); 1000 1001 reg = rtl818x_ioread8(priv, &priv->map->TX_AGC_CTL); 1002 reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_GAIN; 1003 reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL; 1004 reg &= ~RTL818X_TX_AGC_CTL_FEEDBACK_ANT; 1005 rtl818x_iowrite8(priv, &priv->map->TX_AGC_CTL, reg); 1006 1007 reg = RTL818X_TX_CONF_CW_MIN | 1008 (7 << 21 /* MAX TX DMA */) | 1009 RTL818X_TX_CONF_NO_ICV; 1010 rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg); 1011 1012 reg = rtl818x_ioread8(priv, &priv->map->CMD); 1013 reg |= RTL818X_CMD_TX_ENABLE; 1014 reg |= RTL818X_CMD_RX_ENABLE; 1015 rtl818x_iowrite8(priv, &priv->map->CMD, reg); 1016 INIT_DELAYED_WORK(&priv->work, rtl8187_work); 1017 1018 rtl8187_start_exit: 1019 mutex_unlock(&priv->conf_mutex); 1020 return ret; 1021 } 1022 1023 static void rtl8187_stop(struct ieee80211_hw *dev) 1024 { 1025 struct rtl8187_priv *priv = dev->priv; 1026 struct sk_buff *skb; 1027 u32 reg; 1028 1029 mutex_lock(&priv->conf_mutex); 1030 rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0); 1031 1032 reg = rtl818x_ioread8(priv, &priv->map->CMD); 1033 reg &= ~RTL818X_CMD_TX_ENABLE; 1034 reg &= ~RTL818X_CMD_RX_ENABLE; 1035 rtl818x_iowrite8(priv, &priv->map->CMD, reg); 1036 1037 priv->rf->stop(dev); 1038 rtl8187_set_anaparam(priv, false); 1039 1040 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); 1041 reg = rtl818x_ioread8(priv, &priv->map->CONFIG4); 1042 rtl818x_iowrite8(priv, &priv->map->CONFIG4, reg | RTL818X_CONFIG4_VCOOFF); 1043 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); 1044 1045 while ((skb = skb_dequeue(&priv->b_tx_status.queue))) 1046 dev_kfree_skb_any(skb); 1047 1048 usb_kill_anchored_urbs(&priv->anchored); 1049 mutex_unlock(&priv->conf_mutex); 1050 1051 if (!priv->is_rtl8187b) 1052 cancel_delayed_work_sync(&priv->work); 1053 } 1054 1055 static u64 rtl8187_get_tsf(struct ieee80211_hw *dev, struct ieee80211_vif *vif) 1056 { 1057 struct rtl8187_priv *priv = dev->priv; 1058 1059 return rtl818x_ioread32(priv, &priv->map->TSFT[0]) | 1060 (u64)(rtl818x_ioread32(priv, &priv->map->TSFT[1])) << 32; 1061 } 1062 1063 1064 static void rtl8187_beacon_work(struct work_struct *work) 1065 { 1066 struct rtl8187_vif *vif_priv = 1067 container_of(work, struct rtl8187_vif, beacon_work.work); 1068 struct ieee80211_vif *vif = 1069 container_of((void *)vif_priv, struct ieee80211_vif, drv_priv); 1070 struct ieee80211_hw *dev = vif_priv->dev; 1071 struct ieee80211_mgmt *mgmt; 1072 struct sk_buff *skb; 1073 1074 /* don't overflow the tx ring */ 1075 if (ieee80211_queue_stopped(dev, 0)) 1076 goto resched; 1077 1078 /* grab a fresh beacon */ 1079 skb = ieee80211_beacon_get(dev, vif); 1080 if (!skb) 1081 goto resched; 1082 1083 /* 1084 * update beacon timestamp w/ TSF value 1085 * TODO: make hardware update beacon timestamp 1086 */ 1087 mgmt = (struct ieee80211_mgmt *)skb->data; 1088 mgmt->u.beacon.timestamp = cpu_to_le64(rtl8187_get_tsf(dev, vif)); 1089 1090 /* TODO: use actual beacon queue */ 1091 skb_set_queue_mapping(skb, 0); 1092 1093 rtl8187_tx(dev, NULL, skb); 1094 1095 resched: 1096 /* 1097 * schedule next beacon 1098 * TODO: use hardware support for beacon timing 1099 */ 1100 schedule_delayed_work(&vif_priv->beacon_work, 1101 usecs_to_jiffies(1024 * vif->bss_conf.beacon_int)); 1102 } 1103 1104 1105 static int rtl8187_add_interface(struct ieee80211_hw *dev, 1106 struct ieee80211_vif *vif) 1107 { 1108 struct rtl8187_priv *priv = dev->priv; 1109 struct rtl8187_vif *vif_priv; 1110 int i; 1111 int ret = -EOPNOTSUPP; 1112 1113 mutex_lock(&priv->conf_mutex); 1114 if (priv->vif) 1115 goto exit; 1116 1117 switch (vif->type) { 1118 case NL80211_IFTYPE_STATION: 1119 case NL80211_IFTYPE_ADHOC: 1120 break; 1121 default: 1122 goto exit; 1123 } 1124 1125 ret = 0; 1126 priv->vif = vif; 1127 1128 /* Initialize driver private area */ 1129 vif_priv = (struct rtl8187_vif *)&vif->drv_priv; 1130 vif_priv->dev = dev; 1131 INIT_DELAYED_WORK(&vif_priv->beacon_work, rtl8187_beacon_work); 1132 vif_priv->enable_beacon = false; 1133 1134 1135 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); 1136 for (i = 0; i < ETH_ALEN; i++) 1137 rtl818x_iowrite8(priv, &priv->map->MAC[i], 1138 ((u8 *)vif->addr)[i]); 1139 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); 1140 1141 exit: 1142 mutex_unlock(&priv->conf_mutex); 1143 return ret; 1144 } 1145 1146 static void rtl8187_remove_interface(struct ieee80211_hw *dev, 1147 struct ieee80211_vif *vif) 1148 { 1149 struct rtl8187_priv *priv = dev->priv; 1150 mutex_lock(&priv->conf_mutex); 1151 priv->vif = NULL; 1152 mutex_unlock(&priv->conf_mutex); 1153 } 1154 1155 static int rtl8187_config(struct ieee80211_hw *dev, u32 changed) 1156 { 1157 struct rtl8187_priv *priv = dev->priv; 1158 struct ieee80211_conf *conf = &dev->conf; 1159 u32 reg; 1160 1161 mutex_lock(&priv->conf_mutex); 1162 reg = rtl818x_ioread32(priv, &priv->map->TX_CONF); 1163 /* Enable TX loopback on MAC level to avoid TX during channel 1164 * changes, as this has be seen to causes problems and the 1165 * card will stop work until next reset 1166 */ 1167 rtl818x_iowrite32(priv, &priv->map->TX_CONF, 1168 reg | RTL818X_TX_CONF_LOOPBACK_MAC); 1169 priv->rf->set_chan(dev, conf); 1170 msleep(10); 1171 rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg); 1172 1173 rtl818x_iowrite16(priv, &priv->map->ATIM_WND, 2); 1174 rtl818x_iowrite16(priv, &priv->map->ATIMTR_INTERVAL, 100); 1175 rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL, 100); 1176 rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL_TIME, 100); 1177 mutex_unlock(&priv->conf_mutex); 1178 return 0; 1179 } 1180 1181 /* 1182 * With 8187B, AC_*_PARAM clashes with FEMR definition in struct rtl818x_csr for 1183 * example. Thus we have to use raw values for AC_*_PARAM register addresses. 1184 */ 1185 static __le32 *rtl8187b_ac_addr[4] = { 1186 (__le32 *) 0xFFF0, /* AC_VO */ 1187 (__le32 *) 0xFFF4, /* AC_VI */ 1188 (__le32 *) 0xFFFC, /* AC_BK */ 1189 (__le32 *) 0xFFF8, /* AC_BE */ 1190 }; 1191 1192 #define SIFS_TIME 0xa 1193 1194 static void rtl8187_conf_erp(struct rtl8187_priv *priv, bool use_short_slot, 1195 bool use_short_preamble) 1196 { 1197 if (priv->is_rtl8187b) { 1198 u8 difs, eifs; 1199 u16 ack_timeout; 1200 int queue; 1201 1202 if (use_short_slot) { 1203 priv->slot_time = 0x9; 1204 difs = 0x1c; 1205 eifs = 0x53; 1206 } else { 1207 priv->slot_time = 0x14; 1208 difs = 0x32; 1209 eifs = 0x5b; 1210 } 1211 rtl818x_iowrite8(priv, &priv->map->SIFS, 0x22); 1212 rtl818x_iowrite8(priv, &priv->map->SLOT, priv->slot_time); 1213 rtl818x_iowrite8(priv, &priv->map->DIFS, difs); 1214 1215 /* 1216 * BRSR+1 on 8187B is in fact EIFS register 1217 * Value in units of 4 us 1218 */ 1219 rtl818x_iowrite8(priv, (u8 *)&priv->map->BRSR + 1, eifs); 1220 1221 /* 1222 * For 8187B, CARRIER_SENSE_COUNTER is in fact ack timeout 1223 * register. In units of 4 us like eifs register 1224 * ack_timeout = ack duration + plcp + difs + preamble 1225 */ 1226 ack_timeout = 112 + 48 + difs; 1227 if (use_short_preamble) 1228 ack_timeout += 72; 1229 else 1230 ack_timeout += 144; 1231 rtl818x_iowrite8(priv, &priv->map->CARRIER_SENSE_COUNTER, 1232 DIV_ROUND_UP(ack_timeout, 4)); 1233 1234 for (queue = 0; queue < 4; queue++) 1235 rtl818x_iowrite8(priv, (u8 *) rtl8187b_ac_addr[queue], 1236 priv->aifsn[queue] * priv->slot_time + 1237 SIFS_TIME); 1238 } else { 1239 rtl818x_iowrite8(priv, &priv->map->SIFS, 0x22); 1240 if (use_short_slot) { 1241 rtl818x_iowrite8(priv, &priv->map->SLOT, 0x9); 1242 rtl818x_iowrite8(priv, &priv->map->DIFS, 0x14); 1243 rtl818x_iowrite8(priv, &priv->map->EIFS, 91 - 0x14); 1244 } else { 1245 rtl818x_iowrite8(priv, &priv->map->SLOT, 0x14); 1246 rtl818x_iowrite8(priv, &priv->map->DIFS, 0x24); 1247 rtl818x_iowrite8(priv, &priv->map->EIFS, 91 - 0x24); 1248 } 1249 } 1250 } 1251 1252 static void rtl8187_bss_info_changed(struct ieee80211_hw *dev, 1253 struct ieee80211_vif *vif, 1254 struct ieee80211_bss_conf *info, 1255 u32 changed) 1256 { 1257 struct rtl8187_priv *priv = dev->priv; 1258 struct rtl8187_vif *vif_priv; 1259 int i; 1260 u8 reg; 1261 1262 vif_priv = (struct rtl8187_vif *)&vif->drv_priv; 1263 1264 if (changed & BSS_CHANGED_BSSID) { 1265 mutex_lock(&priv->conf_mutex); 1266 for (i = 0; i < ETH_ALEN; i++) 1267 rtl818x_iowrite8(priv, &priv->map->BSSID[i], 1268 info->bssid[i]); 1269 1270 if (priv->is_rtl8187b) 1271 reg = RTL818X_MSR_ENEDCA; 1272 else 1273 reg = 0; 1274 1275 if (is_valid_ether_addr(info->bssid)) { 1276 if (vif->type == NL80211_IFTYPE_ADHOC) 1277 reg |= RTL818X_MSR_ADHOC; 1278 else 1279 reg |= RTL818X_MSR_INFRA; 1280 } 1281 else 1282 reg |= RTL818X_MSR_NO_LINK; 1283 1284 rtl818x_iowrite8(priv, &priv->map->MSR, reg); 1285 1286 mutex_unlock(&priv->conf_mutex); 1287 } 1288 1289 if (changed & (BSS_CHANGED_ERP_SLOT | BSS_CHANGED_ERP_PREAMBLE)) 1290 rtl8187_conf_erp(priv, info->use_short_slot, 1291 info->use_short_preamble); 1292 1293 if (changed & BSS_CHANGED_BEACON_ENABLED) 1294 vif_priv->enable_beacon = info->enable_beacon; 1295 1296 if (changed & (BSS_CHANGED_BEACON_ENABLED | BSS_CHANGED_BEACON)) { 1297 cancel_delayed_work_sync(&vif_priv->beacon_work); 1298 if (vif_priv->enable_beacon) 1299 schedule_work(&vif_priv->beacon_work.work); 1300 } 1301 1302 } 1303 1304 static u64 rtl8187_prepare_multicast(struct ieee80211_hw *dev, 1305 struct netdev_hw_addr_list *mc_list) 1306 { 1307 return netdev_hw_addr_list_count(mc_list); 1308 } 1309 1310 static void rtl8187_configure_filter(struct ieee80211_hw *dev, 1311 unsigned int changed_flags, 1312 unsigned int *total_flags, 1313 u64 multicast) 1314 { 1315 struct rtl8187_priv *priv = dev->priv; 1316 1317 if (changed_flags & FIF_FCSFAIL) 1318 priv->rx_conf ^= RTL818X_RX_CONF_FCS; 1319 if (changed_flags & FIF_CONTROL) 1320 priv->rx_conf ^= RTL818X_RX_CONF_CTRL; 1321 if (*total_flags & FIF_OTHER_BSS || 1322 *total_flags & FIF_ALLMULTI || multicast > 0) 1323 priv->rx_conf |= RTL818X_RX_CONF_MONITOR; 1324 else 1325 priv->rx_conf &= ~RTL818X_RX_CONF_MONITOR; 1326 1327 *total_flags = 0; 1328 1329 if (priv->rx_conf & RTL818X_RX_CONF_FCS) 1330 *total_flags |= FIF_FCSFAIL; 1331 if (priv->rx_conf & RTL818X_RX_CONF_CTRL) 1332 *total_flags |= FIF_CONTROL; 1333 if (priv->rx_conf & RTL818X_RX_CONF_MONITOR) { 1334 *total_flags |= FIF_OTHER_BSS; 1335 *total_flags |= FIF_ALLMULTI; 1336 } 1337 1338 rtl818x_iowrite32_async(priv, &priv->map->RX_CONF, priv->rx_conf); 1339 } 1340 1341 static int rtl8187_conf_tx(struct ieee80211_hw *dev, 1342 struct ieee80211_vif *vif, u16 queue, 1343 const struct ieee80211_tx_queue_params *params) 1344 { 1345 struct rtl8187_priv *priv = dev->priv; 1346 u8 cw_min, cw_max; 1347 1348 if (queue > 3) 1349 return -EINVAL; 1350 1351 cw_min = fls(params->cw_min); 1352 cw_max = fls(params->cw_max); 1353 1354 if (priv->is_rtl8187b) { 1355 priv->aifsn[queue] = params->aifs; 1356 1357 /* 1358 * This is the structure of AC_*_PARAM registers in 8187B: 1359 * - TXOP limit field, bit offset = 16 1360 * - ECWmax, bit offset = 12 1361 * - ECWmin, bit offset = 8 1362 * - AIFS, bit offset = 0 1363 */ 1364 rtl818x_iowrite32(priv, rtl8187b_ac_addr[queue], 1365 (params->txop << 16) | (cw_max << 12) | 1366 (cw_min << 8) | (params->aifs * 1367 priv->slot_time + SIFS_TIME)); 1368 } else { 1369 if (queue != 0) 1370 return -EINVAL; 1371 1372 rtl818x_iowrite8(priv, &priv->map->CW_VAL, 1373 cw_min | (cw_max << 4)); 1374 } 1375 return 0; 1376 } 1377 1378 1379 static const struct ieee80211_ops rtl8187_ops = { 1380 .tx = rtl8187_tx, 1381 .start = rtl8187_start, 1382 .stop = rtl8187_stop, 1383 .add_interface = rtl8187_add_interface, 1384 .remove_interface = rtl8187_remove_interface, 1385 .config = rtl8187_config, 1386 .bss_info_changed = rtl8187_bss_info_changed, 1387 .prepare_multicast = rtl8187_prepare_multicast, 1388 .configure_filter = rtl8187_configure_filter, 1389 .conf_tx = rtl8187_conf_tx, 1390 .rfkill_poll = rtl8187_rfkill_poll, 1391 .get_tsf = rtl8187_get_tsf, 1392 }; 1393 1394 static void rtl8187_eeprom_register_read(struct eeprom_93cx6 *eeprom) 1395 { 1396 struct ieee80211_hw *dev = eeprom->data; 1397 struct rtl8187_priv *priv = dev->priv; 1398 u8 reg = rtl818x_ioread8(priv, &priv->map->EEPROM_CMD); 1399 1400 eeprom->reg_data_in = reg & RTL818X_EEPROM_CMD_WRITE; 1401 eeprom->reg_data_out = reg & RTL818X_EEPROM_CMD_READ; 1402 eeprom->reg_data_clock = reg & RTL818X_EEPROM_CMD_CK; 1403 eeprom->reg_chip_select = reg & RTL818X_EEPROM_CMD_CS; 1404 } 1405 1406 static void rtl8187_eeprom_register_write(struct eeprom_93cx6 *eeprom) 1407 { 1408 struct ieee80211_hw *dev = eeprom->data; 1409 struct rtl8187_priv *priv = dev->priv; 1410 u8 reg = RTL818X_EEPROM_CMD_PROGRAM; 1411 1412 if (eeprom->reg_data_in) 1413 reg |= RTL818X_EEPROM_CMD_WRITE; 1414 if (eeprom->reg_data_out) 1415 reg |= RTL818X_EEPROM_CMD_READ; 1416 if (eeprom->reg_data_clock) 1417 reg |= RTL818X_EEPROM_CMD_CK; 1418 if (eeprom->reg_chip_select) 1419 reg |= RTL818X_EEPROM_CMD_CS; 1420 1421 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, reg); 1422 udelay(10); 1423 } 1424 1425 static int rtl8187_probe(struct usb_interface *intf, 1426 const struct usb_device_id *id) 1427 { 1428 struct usb_device *udev = interface_to_usbdev(intf); 1429 struct ieee80211_hw *dev; 1430 struct rtl8187_priv *priv; 1431 struct eeprom_93cx6 eeprom; 1432 struct ieee80211_channel *channel; 1433 const char *chip_name; 1434 u16 txpwr, reg; 1435 u16 product_id = le16_to_cpu(udev->descriptor.idProduct); 1436 int err, i; 1437 u8 mac_addr[ETH_ALEN]; 1438 1439 dev = ieee80211_alloc_hw(sizeof(*priv), &rtl8187_ops); 1440 if (!dev) { 1441 printk(KERN_ERR "rtl8187: ieee80211 alloc failed\n"); 1442 return -ENOMEM; 1443 } 1444 1445 priv = dev->priv; 1446 priv->is_rtl8187b = (id->driver_info == DEVICE_RTL8187B); 1447 1448 /* allocate "DMA aware" buffer for register accesses */ 1449 priv->io_dmabuf = kmalloc(sizeof(*priv->io_dmabuf), GFP_KERNEL); 1450 if (!priv->io_dmabuf) { 1451 err = -ENOMEM; 1452 goto err_free_dev; 1453 } 1454 mutex_init(&priv->io_mutex); 1455 1456 SET_IEEE80211_DEV(dev, &intf->dev); 1457 usb_set_intfdata(intf, dev); 1458 priv->udev = udev; 1459 1460 usb_get_dev(udev); 1461 1462 skb_queue_head_init(&priv->rx_queue); 1463 1464 BUILD_BUG_ON(sizeof(priv->channels) != sizeof(rtl818x_channels)); 1465 BUILD_BUG_ON(sizeof(priv->rates) != sizeof(rtl818x_rates)); 1466 1467 memcpy(priv->channels, rtl818x_channels, sizeof(rtl818x_channels)); 1468 memcpy(priv->rates, rtl818x_rates, sizeof(rtl818x_rates)); 1469 priv->map = (struct rtl818x_csr *)0xFF00; 1470 1471 priv->band.band = NL80211_BAND_2GHZ; 1472 priv->band.channels = priv->channels; 1473 priv->band.n_channels = ARRAY_SIZE(rtl818x_channels); 1474 priv->band.bitrates = priv->rates; 1475 priv->band.n_bitrates = ARRAY_SIZE(rtl818x_rates); 1476 dev->wiphy->bands[NL80211_BAND_2GHZ] = &priv->band; 1477 1478 1479 ieee80211_hw_set(dev, RX_INCLUDES_FCS); 1480 ieee80211_hw_set(dev, HOST_BROADCAST_PS_BUFFERING); 1481 ieee80211_hw_set(dev, SIGNAL_DBM); 1482 /* Initialize rate-control variables */ 1483 dev->max_rates = 1; 1484 dev->max_rate_tries = RETRY_COUNT; 1485 1486 eeprom.data = dev; 1487 eeprom.register_read = rtl8187_eeprom_register_read; 1488 eeprom.register_write = rtl8187_eeprom_register_write; 1489 if (rtl818x_ioread32(priv, &priv->map->RX_CONF) & (1 << 6)) 1490 eeprom.width = PCI_EEPROM_WIDTH_93C66; 1491 else 1492 eeprom.width = PCI_EEPROM_WIDTH_93C46; 1493 1494 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); 1495 udelay(10); 1496 1497 eeprom_93cx6_multiread(&eeprom, RTL8187_EEPROM_MAC_ADDR, 1498 (__le16 __force *)mac_addr, 3); 1499 if (!is_valid_ether_addr(mac_addr)) { 1500 printk(KERN_WARNING "rtl8187: Invalid hwaddr! Using randomly " 1501 "generated MAC address\n"); 1502 eth_random_addr(mac_addr); 1503 } 1504 SET_IEEE80211_PERM_ADDR(dev, mac_addr); 1505 1506 channel = priv->channels; 1507 for (i = 0; i < 3; i++) { 1508 eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_1 + i, 1509 &txpwr); 1510 (*channel++).hw_value = txpwr & 0xFF; 1511 (*channel++).hw_value = txpwr >> 8; 1512 } 1513 for (i = 0; i < 2; i++) { 1514 eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_4 + i, 1515 &txpwr); 1516 (*channel++).hw_value = txpwr & 0xFF; 1517 (*channel++).hw_value = txpwr >> 8; 1518 } 1519 1520 eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_BASE, 1521 &priv->txpwr_base); 1522 1523 reg = rtl818x_ioread8(priv, &priv->map->PGSELECT) & ~1; 1524 rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg | 1); 1525 /* 0 means asic B-cut, we should use SW 3 wire 1526 * bit-by-bit banging for radio. 1 means we can use 1527 * USB specific request to write radio registers */ 1528 priv->asic_rev = rtl818x_ioread8(priv, (u8 *)0xFFFE) & 0x3; 1529 rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg); 1530 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); 1531 1532 if (!priv->is_rtl8187b) { 1533 u32 reg32; 1534 reg32 = rtl818x_ioread32(priv, &priv->map->TX_CONF); 1535 reg32 &= RTL818X_TX_CONF_HWVER_MASK; 1536 switch (reg32) { 1537 case RTL818X_TX_CONF_R8187vD_B: 1538 /* Some RTL8187B devices have a USB ID of 0x8187 1539 * detect them here */ 1540 chip_name = "RTL8187BvB(early)"; 1541 priv->is_rtl8187b = 1; 1542 priv->hw_rev = RTL8187BvB; 1543 break; 1544 case RTL818X_TX_CONF_R8187vD: 1545 chip_name = "RTL8187vD"; 1546 break; 1547 default: 1548 chip_name = "RTL8187vB (default)"; 1549 } 1550 } else { 1551 /* 1552 * Force USB request to write radio registers for 8187B, Realtek 1553 * only uses it in their sources 1554 */ 1555 /*if (priv->asic_rev == 0) { 1556 printk(KERN_WARNING "rtl8187: Forcing use of USB " 1557 "requests to write to radio registers\n"); 1558 priv->asic_rev = 1; 1559 }*/ 1560 switch (rtl818x_ioread8(priv, (u8 *)0xFFE1)) { 1561 case RTL818X_R8187B_B: 1562 chip_name = "RTL8187BvB"; 1563 priv->hw_rev = RTL8187BvB; 1564 break; 1565 case RTL818X_R8187B_D: 1566 chip_name = "RTL8187BvD"; 1567 priv->hw_rev = RTL8187BvD; 1568 break; 1569 case RTL818X_R8187B_E: 1570 chip_name = "RTL8187BvE"; 1571 priv->hw_rev = RTL8187BvE; 1572 break; 1573 default: 1574 chip_name = "RTL8187BvB (default)"; 1575 priv->hw_rev = RTL8187BvB; 1576 } 1577 } 1578 1579 if (!priv->is_rtl8187b) { 1580 for (i = 0; i < 2; i++) { 1581 eeprom_93cx6_read(&eeprom, 1582 RTL8187_EEPROM_TXPWR_CHAN_6 + i, 1583 &txpwr); 1584 (*channel++).hw_value = txpwr & 0xFF; 1585 (*channel++).hw_value = txpwr >> 8; 1586 } 1587 } else { 1588 eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_6, 1589 &txpwr); 1590 (*channel++).hw_value = txpwr & 0xFF; 1591 1592 eeprom_93cx6_read(&eeprom, 0x0A, &txpwr); 1593 (*channel++).hw_value = txpwr & 0xFF; 1594 1595 eeprom_93cx6_read(&eeprom, 0x1C, &txpwr); 1596 (*channel++).hw_value = txpwr & 0xFF; 1597 (*channel++).hw_value = txpwr >> 8; 1598 } 1599 /* Handle the differing rfkill GPIO bit in different models */ 1600 priv->rfkill_mask = RFKILL_MASK_8187_89_97; 1601 if (product_id == 0x8197 || product_id == 0x8198) { 1602 eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_SELECT_GPIO, ®); 1603 if (reg & 0xFF00) 1604 priv->rfkill_mask = RFKILL_MASK_8198; 1605 } 1606 dev->vif_data_size = sizeof(struct rtl8187_vif); 1607 dev->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION) | 1608 BIT(NL80211_IFTYPE_ADHOC) ; 1609 1610 wiphy_ext_feature_set(dev->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST); 1611 1612 if ((id->driver_info == DEVICE_RTL8187) && priv->is_rtl8187b) 1613 printk(KERN_INFO "rtl8187: inconsistency between id with OEM" 1614 " info!\n"); 1615 1616 priv->rf = rtl8187_detect_rf(dev); 1617 dev->extra_tx_headroom = (!priv->is_rtl8187b) ? 1618 sizeof(struct rtl8187_tx_hdr) : 1619 sizeof(struct rtl8187b_tx_hdr); 1620 if (!priv->is_rtl8187b) 1621 dev->queues = 1; 1622 else 1623 dev->queues = 4; 1624 1625 err = ieee80211_register_hw(dev); 1626 if (err) { 1627 printk(KERN_ERR "rtl8187: Cannot register device\n"); 1628 goto err_free_dmabuf; 1629 } 1630 mutex_init(&priv->conf_mutex); 1631 skb_queue_head_init(&priv->b_tx_status.queue); 1632 1633 wiphy_info(dev->wiphy, "hwaddr %pM, %s V%d + %s, rfkill mask %d\n", 1634 mac_addr, chip_name, priv->asic_rev, priv->rf->name, 1635 priv->rfkill_mask); 1636 1637 #ifdef CONFIG_RTL8187_LEDS 1638 eeprom_93cx6_read(&eeprom, 0x3F, ®); 1639 reg &= 0xFF; 1640 rtl8187_leds_init(dev, reg); 1641 #endif 1642 rtl8187_rfkill_init(dev); 1643 1644 return 0; 1645 1646 err_free_dmabuf: 1647 kfree(priv->io_dmabuf); 1648 usb_set_intfdata(intf, NULL); 1649 usb_put_dev(udev); 1650 err_free_dev: 1651 ieee80211_free_hw(dev); 1652 return err; 1653 } 1654 1655 static void rtl8187_disconnect(struct usb_interface *intf) 1656 { 1657 struct ieee80211_hw *dev = usb_get_intfdata(intf); 1658 struct rtl8187_priv *priv; 1659 1660 if (!dev) 1661 return; 1662 1663 #ifdef CONFIG_RTL8187_LEDS 1664 rtl8187_leds_exit(dev); 1665 #endif 1666 rtl8187_rfkill_exit(dev); 1667 ieee80211_unregister_hw(dev); 1668 1669 priv = dev->priv; 1670 usb_reset_device(priv->udev); 1671 usb_put_dev(interface_to_usbdev(intf)); 1672 kfree(priv->io_dmabuf); 1673 ieee80211_free_hw(dev); 1674 } 1675 1676 static struct usb_driver rtl8187_driver = { 1677 .name = KBUILD_MODNAME, 1678 .id_table = rtl8187_table, 1679 .probe = rtl8187_probe, 1680 .disconnect = rtl8187_disconnect, 1681 .disable_hub_initiated_lpm = 1, 1682 }; 1683 1684 module_usb_driver(rtl8187_driver); 1685