1 2 /* Linux device driver for RTL8180 / RTL8185 / RTL8187SE 3 * 4 * Copyright 2007 Michael Wu <flamingice@sourmilk.net> 5 * Copyright 2007,2014 Andrea Merello <andrea.merello@gmail.com> 6 * 7 * Based on the r8180 driver, which is: 8 * Copyright 2004-2005 Andrea Merello <andrea.merello@gmail.com>, et al. 9 * 10 * Thanks to Realtek for their support! 11 * 12 ************************************************************************ 13 * 14 * The driver was extended to the RTL8187SE in 2014 by 15 * Andrea Merello <andrea.merello@gmail.com> 16 * 17 * based also on: 18 * - portions of rtl8187se Linux staging driver, Copyright Realtek corp. 19 * (available in drivers/staging/rtl8187se directory of Linux 3.14) 20 * - other GPL, unpublished (until now), Linux driver code, 21 * Copyright Larry Finger <Larry.Finger@lwfinger.net> 22 * 23 * A huge thanks goes to Sara V. Nari who forgives me when I'm 24 * sitting in front of my laptop at evening, week-end, night... 25 * 26 * A special thanks goes to Antonio Cuni, who helped me with 27 * some python userspace stuff I used to debug RTL8187SE code, and who 28 * bought a laptop with an unsupported Wi-Fi card some years ago... 29 * 30 * Thanks to Larry Finger for writing some code for rtl8187se and for 31 * his suggestions. 32 * 33 * Thanks to Dan Carpenter for reviewing my initial patch and for his 34 * suggestions. 35 * 36 * Thanks to Bernhard Schiffner for his help in testing and for his 37 * suggestions. 38 * 39 ************************************************************************ 40 * 41 * This program is free software; you can redistribute it and/or modify 42 * it under the terms of the GNU General Public License version 2 as 43 * published by the Free Software Foundation. 44 */ 45 46 #include <linux/interrupt.h> 47 #include <linux/pci.h> 48 #include <linux/slab.h> 49 #include <linux/delay.h> 50 #include <linux/etherdevice.h> 51 #include <linux/eeprom_93cx6.h> 52 #include <linux/module.h> 53 #include <net/mac80211.h> 54 55 #include "rtl8180.h" 56 #include "rtl8225.h" 57 #include "sa2400.h" 58 #include "max2820.h" 59 #include "grf5101.h" 60 #include "rtl8225se.h" 61 62 MODULE_AUTHOR("Michael Wu <flamingice@sourmilk.net>"); 63 MODULE_AUTHOR("Andrea Merello <andrea.merello@gmail.com>"); 64 MODULE_DESCRIPTION("RTL8180 / RTL8185 / RTL8187SE PCI wireless driver"); 65 MODULE_LICENSE("GPL"); 66 67 static const struct pci_device_id rtl8180_table[] = { 68 69 /* rtl8187se */ 70 { PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0x8199) }, 71 72 /* rtl8185 */ 73 { PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0x8185) }, 74 { PCI_DEVICE(PCI_VENDOR_ID_BELKIN, 0x700f) }, 75 { PCI_DEVICE(PCI_VENDOR_ID_BELKIN, 0x701f) }, 76 77 /* rtl8180 */ 78 { PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0x8180) }, 79 { PCI_DEVICE(0x1799, 0x6001) }, 80 { PCI_DEVICE(0x1799, 0x6020) }, 81 { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x3300) }, 82 { PCI_DEVICE(0x1186, 0x3301) }, 83 { PCI_DEVICE(0x1432, 0x7106) }, 84 { } 85 }; 86 87 MODULE_DEVICE_TABLE(pci, rtl8180_table); 88 89 static const struct ieee80211_rate rtl818x_rates[] = { 90 { .bitrate = 10, .hw_value = 0, }, 91 { .bitrate = 20, .hw_value = 1, }, 92 { .bitrate = 55, .hw_value = 2, }, 93 { .bitrate = 110, .hw_value = 3, }, 94 { .bitrate = 60, .hw_value = 4, }, 95 { .bitrate = 90, .hw_value = 5, }, 96 { .bitrate = 120, .hw_value = 6, }, 97 { .bitrate = 180, .hw_value = 7, }, 98 { .bitrate = 240, .hw_value = 8, }, 99 { .bitrate = 360, .hw_value = 9, }, 100 { .bitrate = 480, .hw_value = 10, }, 101 { .bitrate = 540, .hw_value = 11, }, 102 }; 103 104 static const struct ieee80211_channel rtl818x_channels[] = { 105 { .center_freq = 2412 }, 106 { .center_freq = 2417 }, 107 { .center_freq = 2422 }, 108 { .center_freq = 2427 }, 109 { .center_freq = 2432 }, 110 { .center_freq = 2437 }, 111 { .center_freq = 2442 }, 112 { .center_freq = 2447 }, 113 { .center_freq = 2452 }, 114 { .center_freq = 2457 }, 115 { .center_freq = 2462 }, 116 { .center_freq = 2467 }, 117 { .center_freq = 2472 }, 118 { .center_freq = 2484 }, 119 }; 120 121 /* Queues for rtl8187se card 122 * 123 * name | reg | queue 124 * BC | 7 | 6 125 * MG | 1 | 0 126 * HI | 6 | 1 127 * VO | 5 | 2 128 * VI | 4 | 3 129 * BE | 3 | 4 130 * BK | 2 | 5 131 * 132 * The complete map for DMA kick reg using use all queue is: 133 * static const int rtl8187se_queues_map[RTL8187SE_NR_TX_QUEUES] = 134 * {1, 6, 5, 4, 3, 2, 7}; 135 * 136 * .. but.. Because for mac80211 4 queues are enough for QoS we use this 137 * 138 * name | reg | queue 139 * BC | 7 | 4 <- currently not used yet 140 * MG | 1 | x <- Not used 141 * HI | 6 | x <- Not used 142 * VO | 5 | 0 <- used 143 * VI | 4 | 1 <- used 144 * BE | 3 | 2 <- used 145 * BK | 2 | 3 <- used 146 * 147 * Beacon queue could be used, but this is not finished yet. 148 * 149 * I thougth about using the other two queues but I decided not to do this: 150 * 151 * - I'm unsure whether the mac80211 will ever try to use more than 4 queues 152 * by itself. 153 * 154 * - I could route MGMT frames (currently sent over VO queue) to the MGMT 155 * queue but since mac80211 will do not know about it, I will probably gain 156 * some HW priority whenever the VO queue is not empty, but this gain is 157 * limited by the fact that I had to stop the mac80211 queue whenever one of 158 * the VO or MGMT queues is full, stopping also submitting of MGMT frame 159 * to the driver. 160 * 161 * - I don't know how to set in the HW the contention window params for MGMT 162 * and HI-prio queues. 163 */ 164 165 static const int rtl8187se_queues_map[RTL8187SE_NR_TX_QUEUES] = {5, 4, 3, 2, 7}; 166 167 /* Queues for rtl8180/rtl8185 cards 168 * 169 * name | reg | prio 170 * BC | 7 | 3 171 * HI | 6 | 0 172 * NO | 5 | 1 173 * LO | 4 | 2 174 * 175 * The complete map for DMA kick reg using all queue is: 176 * static const int rtl8180_queues_map[RTL8180_NR_TX_QUEUES] = {6, 5, 4, 7}; 177 * 178 * .. but .. Because the mac80211 needs at least 4 queues for QoS or 179 * otherwise QoS can't be done, we use just one. 180 * Beacon queue could be used, but this is not finished yet. 181 * Actual map is: 182 * 183 * name | reg | prio 184 * BC | 7 | 1 <- currently not used yet. 185 * HI | 6 | x <- not used 186 * NO | 5 | x <- not used 187 * LO | 4 | 0 <- used 188 */ 189 190 static const int rtl8180_queues_map[RTL8180_NR_TX_QUEUES] = {4, 7}; 191 192 /* LNA gain table for rtl8187se */ 193 static const u8 rtl8187se_lna_gain[4] = {02, 17, 29, 39}; 194 195 void rtl8180_write_phy(struct ieee80211_hw *dev, u8 addr, u32 data) 196 { 197 struct rtl8180_priv *priv = dev->priv; 198 int i = 10; 199 u32 buf; 200 201 buf = (data << 8) | addr; 202 203 rtl818x_iowrite32(priv, (__le32 __iomem *)&priv->map->PHY[0], buf | 0x80); 204 while (i--) { 205 rtl818x_iowrite32(priv, (__le32 __iomem *)&priv->map->PHY[0], buf); 206 if (rtl818x_ioread8(priv, &priv->map->PHY[2]) == (data & 0xFF)) 207 return; 208 } 209 } 210 211 static void rtl8180_handle_rx(struct ieee80211_hw *dev) 212 { 213 struct rtl8180_priv *priv = dev->priv; 214 struct rtl818x_rx_cmd_desc *cmd_desc; 215 unsigned int count = 32; 216 u8 agc, sq; 217 s8 signal = 1; 218 dma_addr_t mapping; 219 220 while (count--) { 221 void *entry = priv->rx_ring + priv->rx_idx * priv->rx_ring_sz; 222 struct sk_buff *skb = priv->rx_buf[priv->rx_idx]; 223 u32 flags, flags2, flags3 = 0; 224 u64 tsft; 225 226 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { 227 struct rtl8187se_rx_desc *desc = entry; 228 229 flags = le32_to_cpu(desc->flags); 230 /* if ownership flag is set, then we can trust the 231 * HW has written other fields. We must not trust 232 * other descriptor data read before we checked (read) 233 * the ownership flag 234 */ 235 rmb(); 236 flags3 = le32_to_cpu(desc->flags3); 237 flags2 = le32_to_cpu(desc->flags2); 238 tsft = le64_to_cpu(desc->tsft); 239 } else { 240 struct rtl8180_rx_desc *desc = entry; 241 242 flags = le32_to_cpu(desc->flags); 243 /* same as above */ 244 rmb(); 245 flags2 = le32_to_cpu(desc->flags2); 246 tsft = le64_to_cpu(desc->tsft); 247 } 248 249 if (flags & RTL818X_RX_DESC_FLAG_OWN) 250 return; 251 252 if (unlikely(flags & (RTL818X_RX_DESC_FLAG_DMA_FAIL | 253 RTL818X_RX_DESC_FLAG_FOF | 254 RTL818X_RX_DESC_FLAG_RX_ERR))) 255 goto done; 256 else { 257 struct ieee80211_rx_status rx_status = {0}; 258 struct sk_buff *new_skb = dev_alloc_skb(MAX_RX_SIZE); 259 260 if (unlikely(!new_skb)) 261 goto done; 262 263 mapping = pci_map_single(priv->pdev, 264 skb_tail_pointer(new_skb), 265 MAX_RX_SIZE, PCI_DMA_FROMDEVICE); 266 267 if (pci_dma_mapping_error(priv->pdev, mapping)) { 268 kfree_skb(new_skb); 269 dev_err(&priv->pdev->dev, "RX DMA map error\n"); 270 271 goto done; 272 } 273 274 pci_unmap_single(priv->pdev, 275 *((dma_addr_t *)skb->cb), 276 MAX_RX_SIZE, PCI_DMA_FROMDEVICE); 277 skb_put(skb, flags & 0xFFF); 278 279 rx_status.antenna = (flags2 >> 15) & 1; 280 rx_status.rate_idx = (flags >> 20) & 0xF; 281 agc = (flags2 >> 17) & 0x7F; 282 283 switch (priv->chip_family) { 284 case RTL818X_CHIP_FAMILY_RTL8185: 285 if (rx_status.rate_idx > 3) 286 signal = -clamp_t(u8, agc, 25, 90) - 9; 287 else 288 signal = -clamp_t(u8, agc, 30, 95); 289 break; 290 case RTL818X_CHIP_FAMILY_RTL8180: 291 sq = flags2 & 0xff; 292 signal = priv->rf->calc_rssi(agc, sq); 293 break; 294 case RTL818X_CHIP_FAMILY_RTL8187SE: 295 /* OFDM measure reported by HW is signed, 296 * in 0.5dBm unit, with zero centered @ -41dBm 297 * input signal. 298 */ 299 if (rx_status.rate_idx > 3) { 300 signal = (s8)((flags3 >> 16) & 0xff); 301 signal = signal / 2 - 41; 302 } else { 303 int idx, bb; 304 305 idx = (agc & 0x60) >> 5; 306 bb = (agc & 0x1F) * 2; 307 /* bias + BB gain + LNA gain */ 308 signal = 4 - bb - rtl8187se_lna_gain[idx]; 309 } 310 break; 311 } 312 rx_status.signal = signal; 313 rx_status.freq = dev->conf.chandef.chan->center_freq; 314 rx_status.band = dev->conf.chandef.chan->band; 315 rx_status.mactime = tsft; 316 rx_status.flag |= RX_FLAG_MACTIME_START; 317 if (flags & RTL818X_RX_DESC_FLAG_SPLCP) 318 rx_status.enc_flags |= RX_ENC_FLAG_SHORTPRE; 319 if (flags & RTL818X_RX_DESC_FLAG_CRC32_ERR) 320 rx_status.flag |= RX_FLAG_FAILED_FCS_CRC; 321 322 memcpy(IEEE80211_SKB_RXCB(skb), &rx_status, sizeof(rx_status)); 323 ieee80211_rx_irqsafe(dev, skb); 324 325 skb = new_skb; 326 priv->rx_buf[priv->rx_idx] = skb; 327 *((dma_addr_t *) skb->cb) = mapping; 328 } 329 330 done: 331 cmd_desc = entry; 332 cmd_desc->rx_buf = cpu_to_le32(*((dma_addr_t *)skb->cb)); 333 cmd_desc->flags = cpu_to_le32(RTL818X_RX_DESC_FLAG_OWN | 334 MAX_RX_SIZE); 335 if (priv->rx_idx == 31) 336 cmd_desc->flags |= 337 cpu_to_le32(RTL818X_RX_DESC_FLAG_EOR); 338 priv->rx_idx = (priv->rx_idx + 1) % 32; 339 } 340 } 341 342 static void rtl8180_handle_tx(struct ieee80211_hw *dev, unsigned int prio) 343 { 344 struct rtl8180_priv *priv = dev->priv; 345 struct rtl8180_tx_ring *ring = &priv->tx_ring[prio]; 346 347 while (skb_queue_len(&ring->queue)) { 348 struct rtl8180_tx_desc *entry = &ring->desc[ring->idx]; 349 struct sk_buff *skb; 350 struct ieee80211_tx_info *info; 351 u32 flags = le32_to_cpu(entry->flags); 352 353 if (flags & RTL818X_TX_DESC_FLAG_OWN) 354 return; 355 356 ring->idx = (ring->idx + 1) % ring->entries; 357 skb = __skb_dequeue(&ring->queue); 358 pci_unmap_single(priv->pdev, le32_to_cpu(entry->tx_buf), 359 skb->len, PCI_DMA_TODEVICE); 360 361 info = IEEE80211_SKB_CB(skb); 362 ieee80211_tx_info_clear_status(info); 363 364 if (!(info->flags & IEEE80211_TX_CTL_NO_ACK) && 365 (flags & RTL818X_TX_DESC_FLAG_TX_OK)) 366 info->flags |= IEEE80211_TX_STAT_ACK; 367 368 info->status.rates[0].count = (flags & 0xFF) + 1; 369 370 ieee80211_tx_status_irqsafe(dev, skb); 371 if (ring->entries - skb_queue_len(&ring->queue) == 2) 372 ieee80211_wake_queue(dev, prio); 373 } 374 } 375 376 static irqreturn_t rtl8187se_interrupt(int irq, void *dev_id) 377 { 378 struct ieee80211_hw *dev = dev_id; 379 struct rtl8180_priv *priv = dev->priv; 380 u32 reg; 381 unsigned long flags; 382 static int desc_err; 383 384 spin_lock_irqsave(&priv->lock, flags); 385 /* Note: 32-bit interrupt status */ 386 reg = rtl818x_ioread32(priv, &priv->map->INT_STATUS_SE); 387 if (unlikely(reg == 0xFFFFFFFF)) { 388 spin_unlock_irqrestore(&priv->lock, flags); 389 return IRQ_HANDLED; 390 } 391 392 rtl818x_iowrite32(priv, &priv->map->INT_STATUS_SE, reg); 393 394 if (reg & IMR_TIMEOUT1) 395 rtl818x_iowrite32(priv, &priv->map->INT_TIMEOUT, 0); 396 397 if (reg & (IMR_TBDOK | IMR_TBDER)) 398 rtl8180_handle_tx(dev, 4); 399 400 if (reg & (IMR_TVODOK | IMR_TVODER)) 401 rtl8180_handle_tx(dev, 0); 402 403 if (reg & (IMR_TVIDOK | IMR_TVIDER)) 404 rtl8180_handle_tx(dev, 1); 405 406 if (reg & (IMR_TBEDOK | IMR_TBEDER)) 407 rtl8180_handle_tx(dev, 2); 408 409 if (reg & (IMR_TBKDOK | IMR_TBKDER)) 410 rtl8180_handle_tx(dev, 3); 411 412 if (reg & (IMR_ROK | IMR_RER | RTL818X_INT_SE_RX_DU | IMR_RQOSOK)) 413 rtl8180_handle_rx(dev); 414 /* The interface sometimes generates several RX DMA descriptor errors 415 * at startup. Do not report these. 416 */ 417 if ((reg & RTL818X_INT_SE_RX_DU) && desc_err++ > 2) 418 if (net_ratelimit()) 419 wiphy_err(dev->wiphy, "No RX DMA Descriptor avail\n"); 420 421 spin_unlock_irqrestore(&priv->lock, flags); 422 return IRQ_HANDLED; 423 } 424 425 static irqreturn_t rtl8180_interrupt(int irq, void *dev_id) 426 { 427 struct ieee80211_hw *dev = dev_id; 428 struct rtl8180_priv *priv = dev->priv; 429 u16 reg; 430 431 spin_lock(&priv->lock); 432 reg = rtl818x_ioread16(priv, &priv->map->INT_STATUS); 433 if (unlikely(reg == 0xFFFF)) { 434 spin_unlock(&priv->lock); 435 return IRQ_HANDLED; 436 } 437 438 rtl818x_iowrite16(priv, &priv->map->INT_STATUS, reg); 439 440 if (reg & (RTL818X_INT_TXB_OK | RTL818X_INT_TXB_ERR)) 441 rtl8180_handle_tx(dev, 1); 442 443 if (reg & (RTL818X_INT_TXL_OK | RTL818X_INT_TXL_ERR)) 444 rtl8180_handle_tx(dev, 0); 445 446 if (reg & (RTL818X_INT_RX_OK | RTL818X_INT_RX_ERR)) 447 rtl8180_handle_rx(dev); 448 449 spin_unlock(&priv->lock); 450 451 return IRQ_HANDLED; 452 } 453 454 static void rtl8180_tx(struct ieee80211_hw *dev, 455 struct ieee80211_tx_control *control, 456 struct sk_buff *skb) 457 { 458 struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); 459 struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data; 460 struct rtl8180_priv *priv = dev->priv; 461 struct rtl8180_tx_ring *ring; 462 struct rtl8180_tx_desc *entry; 463 unsigned long flags; 464 unsigned int idx, prio, hw_prio; 465 dma_addr_t mapping; 466 u32 tx_flags; 467 u8 rc_flags; 468 u16 plcp_len = 0; 469 __le16 rts_duration = 0; 470 /* do arithmetic and then convert to le16 */ 471 u16 frame_duration = 0; 472 473 prio = skb_get_queue_mapping(skb); 474 ring = &priv->tx_ring[prio]; 475 476 mapping = pci_map_single(priv->pdev, skb->data, 477 skb->len, PCI_DMA_TODEVICE); 478 479 if (pci_dma_mapping_error(priv->pdev, mapping)) { 480 kfree_skb(skb); 481 dev_err(&priv->pdev->dev, "TX DMA mapping error\n"); 482 return; 483 } 484 485 tx_flags = RTL818X_TX_DESC_FLAG_OWN | RTL818X_TX_DESC_FLAG_FS | 486 RTL818X_TX_DESC_FLAG_LS | 487 (ieee80211_get_tx_rate(dev, info)->hw_value << 24) | 488 skb->len; 489 490 if (priv->chip_family != RTL818X_CHIP_FAMILY_RTL8180) 491 tx_flags |= RTL818X_TX_DESC_FLAG_DMA | 492 RTL818X_TX_DESC_FLAG_NO_ENC; 493 494 rc_flags = info->control.rates[0].flags; 495 496 /* HW will perform RTS-CTS when only RTS flags is set. 497 * HW will perform CTS-to-self when both RTS and CTS flags are set. 498 * RTS rate and RTS duration will be used also for CTS-to-self. 499 */ 500 if (rc_flags & IEEE80211_TX_RC_USE_RTS_CTS) { 501 tx_flags |= RTL818X_TX_DESC_FLAG_RTS; 502 tx_flags |= ieee80211_get_rts_cts_rate(dev, info)->hw_value << 19; 503 rts_duration = ieee80211_rts_duration(dev, priv->vif, 504 skb->len, info); 505 } else if (rc_flags & IEEE80211_TX_RC_USE_CTS_PROTECT) { 506 tx_flags |= RTL818X_TX_DESC_FLAG_RTS | RTL818X_TX_DESC_FLAG_CTS; 507 tx_flags |= ieee80211_get_rts_cts_rate(dev, info)->hw_value << 19; 508 rts_duration = ieee80211_ctstoself_duration(dev, priv->vif, 509 skb->len, info); 510 } 511 512 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8180) { 513 unsigned int remainder; 514 515 plcp_len = DIV_ROUND_UP(16 * (skb->len + 4), 516 (ieee80211_get_tx_rate(dev, info)->bitrate * 2) / 10); 517 remainder = (16 * (skb->len + 4)) % 518 ((ieee80211_get_tx_rate(dev, info)->bitrate * 2) / 10); 519 if (remainder <= 6) 520 plcp_len |= 1 << 15; 521 } 522 523 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { 524 __le16 duration; 525 /* SIFS time (required by HW) is already included by 526 * ieee80211_generic_frame_duration 527 */ 528 duration = ieee80211_generic_frame_duration(dev, priv->vif, 529 NL80211_BAND_2GHZ, skb->len, 530 ieee80211_get_tx_rate(dev, info)); 531 532 frame_duration = priv->ack_time + le16_to_cpu(duration); 533 } 534 535 spin_lock_irqsave(&priv->lock, flags); 536 537 if (info->flags & IEEE80211_TX_CTL_ASSIGN_SEQ) { 538 if (info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT) 539 priv->seqno += 0x10; 540 hdr->seq_ctrl &= cpu_to_le16(IEEE80211_SCTL_FRAG); 541 hdr->seq_ctrl |= cpu_to_le16(priv->seqno); 542 } 543 544 idx = (ring->idx + skb_queue_len(&ring->queue)) % ring->entries; 545 entry = &ring->desc[idx]; 546 547 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { 548 entry->frame_duration = cpu_to_le16(frame_duration); 549 entry->frame_len_se = cpu_to_le16(skb->len); 550 551 /* tpc polarity */ 552 entry->flags3 = cpu_to_le16(1<<4); 553 } else 554 entry->frame_len = cpu_to_le32(skb->len); 555 556 entry->rts_duration = rts_duration; 557 entry->plcp_len = cpu_to_le16(plcp_len); 558 entry->tx_buf = cpu_to_le32(mapping); 559 560 entry->retry_limit = info->control.rates[0].count - 1; 561 562 /* We must be sure that tx_flags is written last because the HW 563 * looks at it to check if the rest of data is valid or not 564 */ 565 wmb(); 566 entry->flags = cpu_to_le32(tx_flags); 567 /* We must be sure this has been written before followings HW 568 * register write, because this write will made the HW attempts 569 * to DMA the just-written data 570 */ 571 wmb(); 572 573 __skb_queue_tail(&ring->queue, skb); 574 if (ring->entries - skb_queue_len(&ring->queue) < 2) 575 ieee80211_stop_queue(dev, prio); 576 577 spin_unlock_irqrestore(&priv->lock, flags); 578 579 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { 580 /* just poll: rings are stopped with TPPollStop reg */ 581 hw_prio = rtl8187se_queues_map[prio]; 582 rtl818x_iowrite8(priv, &priv->map->TX_DMA_POLLING, 583 (1 << hw_prio)); 584 } else { 585 hw_prio = rtl8180_queues_map[prio]; 586 rtl818x_iowrite8(priv, &priv->map->TX_DMA_POLLING, 587 (1 << hw_prio) | /* ring to poll */ 588 (1<<1) | (1<<2));/* stopped rings */ 589 } 590 } 591 592 static void rtl8180_set_anaparam3(struct rtl8180_priv *priv, u16 anaparam3) 593 { 594 u8 reg; 595 596 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, 597 RTL818X_EEPROM_CMD_CONFIG); 598 599 reg = rtl818x_ioread8(priv, &priv->map->CONFIG3); 600 rtl818x_iowrite8(priv, &priv->map->CONFIG3, 601 reg | RTL818X_CONFIG3_ANAPARAM_WRITE); 602 603 rtl818x_iowrite16(priv, &priv->map->ANAPARAM3, anaparam3); 604 605 rtl818x_iowrite8(priv, &priv->map->CONFIG3, 606 reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE); 607 608 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, 609 RTL818X_EEPROM_CMD_NORMAL); 610 } 611 612 void rtl8180_set_anaparam2(struct rtl8180_priv *priv, u32 anaparam2) 613 { 614 u8 reg; 615 616 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, 617 RTL818X_EEPROM_CMD_CONFIG); 618 619 reg = rtl818x_ioread8(priv, &priv->map->CONFIG3); 620 rtl818x_iowrite8(priv, &priv->map->CONFIG3, 621 reg | RTL818X_CONFIG3_ANAPARAM_WRITE); 622 623 rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, anaparam2); 624 625 rtl818x_iowrite8(priv, &priv->map->CONFIG3, 626 reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE); 627 628 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, 629 RTL818X_EEPROM_CMD_NORMAL); 630 } 631 632 void rtl8180_set_anaparam(struct rtl8180_priv *priv, u32 anaparam) 633 { 634 u8 reg; 635 636 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); 637 reg = rtl818x_ioread8(priv, &priv->map->CONFIG3); 638 rtl818x_iowrite8(priv, &priv->map->CONFIG3, 639 reg | RTL818X_CONFIG3_ANAPARAM_WRITE); 640 rtl818x_iowrite32(priv, &priv->map->ANAPARAM, anaparam); 641 rtl818x_iowrite8(priv, &priv->map->CONFIG3, 642 reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE); 643 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); 644 } 645 646 static void rtl8187se_mac_config(struct ieee80211_hw *dev) 647 { 648 struct rtl8180_priv *priv = dev->priv; 649 u8 reg; 650 651 rtl818x_iowrite32(priv, REG_ADDR4(0x1F0), 0); 652 rtl818x_ioread32(priv, REG_ADDR4(0x1F0)); 653 rtl818x_iowrite32(priv, REG_ADDR4(0x1F4), 0); 654 rtl818x_ioread32(priv, REG_ADDR4(0x1F4)); 655 rtl818x_iowrite8(priv, REG_ADDR1(0x1F8), 0); 656 rtl818x_ioread8(priv, REG_ADDR1(0x1F8)); 657 /* Enable DA10 TX power saving */ 658 reg = rtl818x_ioread8(priv, &priv->map->PHY_PR); 659 rtl818x_iowrite8(priv, &priv->map->PHY_PR, reg | 0x04); 660 /* Power */ 661 rtl818x_iowrite16(priv, PI_DATA_REG, 0x1000); 662 rtl818x_iowrite16(priv, SI_DATA_REG, 0x1000); 663 /* AFE - default to power ON */ 664 rtl818x_iowrite16(priv, REG_ADDR2(0x370), 0x0560); 665 rtl818x_iowrite16(priv, REG_ADDR2(0x372), 0x0560); 666 rtl818x_iowrite16(priv, REG_ADDR2(0x374), 0x0DA4); 667 rtl818x_iowrite16(priv, REG_ADDR2(0x376), 0x0DA4); 668 rtl818x_iowrite16(priv, REG_ADDR2(0x378), 0x0560); 669 rtl818x_iowrite16(priv, REG_ADDR2(0x37A), 0x0560); 670 rtl818x_iowrite16(priv, REG_ADDR2(0x37C), 0x00EC); 671 rtl818x_iowrite16(priv, REG_ADDR2(0x37E), 0x00EC); 672 rtl818x_iowrite8(priv, REG_ADDR1(0x24E), 0x01); 673 /* unknown, needed for suspend to RAM resume */ 674 rtl818x_iowrite8(priv, REG_ADDR1(0x0A), 0x72); 675 } 676 677 static void rtl8187se_set_antenna_config(struct ieee80211_hw *dev, u8 def_ant, 678 bool diversity) 679 { 680 struct rtl8180_priv *priv = dev->priv; 681 682 rtl8225_write_phy_cck(dev, 0x0C, 0x09); 683 if (diversity) { 684 if (def_ant == 1) { 685 rtl818x_iowrite8(priv, &priv->map->TX_ANTENNA, 0x00); 686 rtl8225_write_phy_cck(dev, 0x11, 0xBB); 687 rtl8225_write_phy_cck(dev, 0x01, 0xC7); 688 rtl8225_write_phy_ofdm(dev, 0x0D, 0x54); 689 rtl8225_write_phy_ofdm(dev, 0x18, 0xB2); 690 } else { /* main antenna */ 691 rtl818x_iowrite8(priv, &priv->map->TX_ANTENNA, 0x03); 692 rtl8225_write_phy_cck(dev, 0x11, 0x9B); 693 rtl8225_write_phy_cck(dev, 0x01, 0xC7); 694 rtl8225_write_phy_ofdm(dev, 0x0D, 0x5C); 695 rtl8225_write_phy_ofdm(dev, 0x18, 0xB2); 696 } 697 } else { /* disable antenna diversity */ 698 if (def_ant == 1) { 699 rtl818x_iowrite8(priv, &priv->map->TX_ANTENNA, 0x00); 700 rtl8225_write_phy_cck(dev, 0x11, 0xBB); 701 rtl8225_write_phy_cck(dev, 0x01, 0x47); 702 rtl8225_write_phy_ofdm(dev, 0x0D, 0x54); 703 rtl8225_write_phy_ofdm(dev, 0x18, 0x32); 704 } else { /* main antenna */ 705 rtl818x_iowrite8(priv, &priv->map->TX_ANTENNA, 0x03); 706 rtl8225_write_phy_cck(dev, 0x11, 0x9B); 707 rtl8225_write_phy_cck(dev, 0x01, 0x47); 708 rtl8225_write_phy_ofdm(dev, 0x0D, 0x5C); 709 rtl8225_write_phy_ofdm(dev, 0x18, 0x32); 710 } 711 } 712 /* priv->curr_ant = def_ant; */ 713 } 714 715 static void rtl8180_int_enable(struct ieee80211_hw *dev) 716 { 717 struct rtl8180_priv *priv = dev->priv; 718 719 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { 720 rtl818x_iowrite32(priv, &priv->map->IMR, 721 IMR_TBDER | IMR_TBDOK | 722 IMR_TVODER | IMR_TVODOK | 723 IMR_TVIDER | IMR_TVIDOK | 724 IMR_TBEDER | IMR_TBEDOK | 725 IMR_TBKDER | IMR_TBKDOK | 726 IMR_RDU | IMR_RER | 727 IMR_ROK | IMR_RQOSOK); 728 } else { 729 rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0xFFFF); 730 } 731 } 732 733 static void rtl8180_int_disable(struct ieee80211_hw *dev) 734 { 735 struct rtl8180_priv *priv = dev->priv; 736 737 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { 738 rtl818x_iowrite32(priv, &priv->map->IMR, 0); 739 } else { 740 rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0); 741 } 742 } 743 744 static void rtl8180_conf_basic_rates(struct ieee80211_hw *dev, 745 u32 basic_mask) 746 { 747 struct rtl8180_priv *priv = dev->priv; 748 u16 reg; 749 u32 resp_mask; 750 u8 basic_max; 751 u8 resp_max, resp_min; 752 753 resp_mask = basic_mask; 754 /* IEEE80211 says the response rate should be equal to the highest basic 755 * rate that is not faster than received frame. But it says also that if 756 * the basic rate set does not contains any rate for the current 757 * modulation class then mandatory rate set must be used for that 758 * modulation class. Eventually add OFDM mandatory rates.. 759 */ 760 if ((resp_mask & 0xf) == resp_mask) 761 resp_mask |= 0x150; /* 6, 12, 24Mbps */ 762 763 switch (priv->chip_family) { 764 765 case RTL818X_CHIP_FAMILY_RTL8180: 766 /* in 8180 this is NOT a BITMAP */ 767 basic_max = fls(basic_mask) - 1; 768 reg = rtl818x_ioread16(priv, &priv->map->BRSR); 769 reg &= ~3; 770 reg |= basic_max; 771 rtl818x_iowrite16(priv, &priv->map->BRSR, reg); 772 break; 773 774 case RTL818X_CHIP_FAMILY_RTL8185: 775 resp_max = fls(resp_mask) - 1; 776 resp_min = ffs(resp_mask) - 1; 777 /* in 8185 this is a BITMAP */ 778 rtl818x_iowrite16(priv, &priv->map->BRSR, basic_mask); 779 rtl818x_iowrite8(priv, &priv->map->RESP_RATE, (resp_max << 4) | 780 resp_min); 781 break; 782 783 case RTL818X_CHIP_FAMILY_RTL8187SE: 784 /* in 8187se this is a BITMAP. BRSR reg actually sets 785 * response rates. 786 */ 787 rtl818x_iowrite16(priv, &priv->map->BRSR_8187SE, resp_mask); 788 break; 789 } 790 } 791 792 static void rtl8180_config_cardbus(struct ieee80211_hw *dev) 793 { 794 struct rtl8180_priv *priv = dev->priv; 795 u16 reg16; 796 u8 reg8; 797 798 reg8 = rtl818x_ioread8(priv, &priv->map->CONFIG3); 799 reg8 |= 1 << 1; 800 rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg8); 801 802 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { 803 rtl818x_iowrite16(priv, FEMR_SE, 0xffff); 804 } else { 805 reg16 = rtl818x_ioread16(priv, &priv->map->FEMR); 806 reg16 |= (1 << 15) | (1 << 14) | (1 << 4); 807 rtl818x_iowrite16(priv, &priv->map->FEMR, reg16); 808 } 809 810 } 811 812 static int rtl8180_init_hw(struct ieee80211_hw *dev) 813 { 814 struct rtl8180_priv *priv = dev->priv; 815 u16 reg; 816 u32 reg32; 817 818 rtl818x_iowrite8(priv, &priv->map->CMD, 0); 819 rtl818x_ioread8(priv, &priv->map->CMD); 820 msleep(10); 821 822 /* reset */ 823 rtl8180_int_disable(dev); 824 rtl818x_ioread8(priv, &priv->map->CMD); 825 826 reg = rtl818x_ioread8(priv, &priv->map->CMD); 827 reg &= (1 << 1); 828 reg |= RTL818X_CMD_RESET; 829 rtl818x_iowrite8(priv, &priv->map->CMD, RTL818X_CMD_RESET); 830 rtl818x_ioread8(priv, &priv->map->CMD); 831 msleep(200); 832 833 /* check success of reset */ 834 if (rtl818x_ioread8(priv, &priv->map->CMD) & RTL818X_CMD_RESET) { 835 wiphy_err(dev->wiphy, "reset timeout!\n"); 836 return -ETIMEDOUT; 837 } 838 839 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_LOAD); 840 rtl818x_ioread8(priv, &priv->map->CMD); 841 msleep(200); 842 843 if (rtl818x_ioread8(priv, &priv->map->CONFIG3) & (1 << 3)) { 844 rtl8180_config_cardbus(dev); 845 } 846 847 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) 848 rtl818x_iowrite8(priv, &priv->map->MSR, RTL818X_MSR_ENEDCA); 849 else 850 rtl818x_iowrite8(priv, &priv->map->MSR, 0); 851 852 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8180) 853 rtl8180_set_anaparam(priv, priv->anaparam); 854 855 rtl818x_iowrite32(priv, &priv->map->RDSAR, priv->rx_ring_dma); 856 /* mac80211 queue have higher prio for lower index. The last queue 857 * (that mac80211 is not aware of) is reserved for beacons (and have 858 * the highest priority on the NIC) 859 */ 860 if (priv->chip_family != RTL818X_CHIP_FAMILY_RTL8187SE) { 861 rtl818x_iowrite32(priv, &priv->map->TBDA, 862 priv->tx_ring[1].dma); 863 rtl818x_iowrite32(priv, &priv->map->TLPDA, 864 priv->tx_ring[0].dma); 865 } else { 866 rtl818x_iowrite32(priv, &priv->map->TBDA, 867 priv->tx_ring[4].dma); 868 rtl818x_iowrite32(priv, &priv->map->TVODA, 869 priv->tx_ring[0].dma); 870 rtl818x_iowrite32(priv, &priv->map->TVIDA, 871 priv->tx_ring[1].dma); 872 rtl818x_iowrite32(priv, &priv->map->TBEDA, 873 priv->tx_ring[2].dma); 874 rtl818x_iowrite32(priv, &priv->map->TBKDA, 875 priv->tx_ring[3].dma); 876 } 877 878 /* TODO: necessary? specs indicate not */ 879 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); 880 reg = rtl818x_ioread8(priv, &priv->map->CONFIG2); 881 rtl818x_iowrite8(priv, &priv->map->CONFIG2, reg & ~(1 << 3)); 882 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8185) { 883 reg = rtl818x_ioread8(priv, &priv->map->CONFIG2); 884 rtl818x_iowrite8(priv, &priv->map->CONFIG2, reg | (1 << 4)); 885 } 886 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); 887 888 /* TODO: set CONFIG5 for calibrating AGC on rtl8180 + philips radio? */ 889 890 /* TODO: turn off hw wep on rtl8180 */ 891 892 rtl818x_iowrite32(priv, &priv->map->INT_TIMEOUT, 0); 893 894 if (priv->chip_family != RTL818X_CHIP_FAMILY_RTL8180) { 895 rtl818x_iowrite8(priv, &priv->map->WPA_CONF, 0); 896 rtl818x_iowrite8(priv, &priv->map->RATE_FALLBACK, 0); 897 } else { 898 rtl818x_iowrite8(priv, &priv->map->SECURITY, 0); 899 900 rtl818x_iowrite8(priv, &priv->map->PHY_DELAY, 0x6); 901 rtl818x_iowrite8(priv, &priv->map->CARRIER_SENSE_COUNTER, 0x4C); 902 } 903 904 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8185) { 905 /* TODO: set ClkRun enable? necessary? */ 906 reg = rtl818x_ioread8(priv, &priv->map->GP_ENABLE); 907 rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, reg & ~(1 << 6)); 908 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); 909 reg = rtl818x_ioread8(priv, &priv->map->CONFIG3); 910 rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | (1 << 2)); 911 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); 912 /* fix eccessive IFS after CTS-to-self */ 913 if (priv->map_pio) { 914 u8 reg; 915 916 reg = rtl818x_ioread8(priv, &priv->map->PGSELECT); 917 rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg | 1); 918 rtl818x_iowrite8(priv, REG_ADDR1(0xff), 0x35); 919 rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg); 920 } else 921 rtl818x_iowrite8(priv, REG_ADDR1(0x1ff), 0x35); 922 } 923 924 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { 925 926 /* the set auto rate fallback bitmask from 1M to 54 Mb/s */ 927 rtl818x_iowrite16(priv, ARFR, 0xFFF); 928 rtl818x_ioread16(priv, ARFR); 929 930 /* stop unused queus (no dma alloc) */ 931 rtl818x_iowrite8(priv, &priv->map->TPPOLL_STOP, 932 RTL818x_TPPOLL_STOP_MG | RTL818x_TPPOLL_STOP_HI); 933 934 rtl818x_iowrite8(priv, &priv->map->ACM_CONTROL, 0x00); 935 rtl818x_iowrite16(priv, &priv->map->TID_AC_MAP, 0xFA50); 936 937 rtl818x_iowrite16(priv, &priv->map->INT_MIG, 0); 938 939 /* some black magic here.. */ 940 rtl8187se_mac_config(dev); 941 942 rtl818x_iowrite16(priv, RFSW_CTRL, 0x569A); 943 rtl818x_ioread16(priv, RFSW_CTRL); 944 945 rtl8180_set_anaparam(priv, RTL8225SE_ANAPARAM_ON); 946 rtl8180_set_anaparam2(priv, RTL8225SE_ANAPARAM2_ON); 947 rtl8180_set_anaparam3(priv, RTL8225SE_ANAPARAM3); 948 949 950 rtl818x_iowrite8(priv, &priv->map->CONFIG5, 951 rtl818x_ioread8(priv, &priv->map->CONFIG5) & 0x7F); 952 953 /*probably this switch led on */ 954 rtl818x_iowrite8(priv, &priv->map->PGSELECT, 955 rtl818x_ioread8(priv, &priv->map->PGSELECT) | 0x08); 956 957 rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, 0x0480); 958 rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1BFF); 959 rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0x2488); 960 961 rtl818x_iowrite32(priv, &priv->map->RF_TIMING, 0x4003); 962 963 /* the reference code mac hardcode table write 964 * this reg by doing byte-wide accesses. 965 * It does it just for lowest and highest byte.. 966 */ 967 reg32 = rtl818x_ioread32(priv, &priv->map->RF_PARA); 968 reg32 &= 0x00ffff00; 969 reg32 |= 0xb8000054; 970 rtl818x_iowrite32(priv, &priv->map->RF_PARA, reg32); 971 } else 972 /* stop unused queus (no dma alloc) */ 973 rtl818x_iowrite8(priv, &priv->map->TX_DMA_POLLING, 974 (1<<1) | (1<<2)); 975 976 priv->rf->init(dev); 977 978 /* default basic rates are 1,2 Mbps for rtl8180. 1,2,6,9,12,18,24 Mbps 979 * otherwise. bitmask 0x3 and 0x01f3 respectively. 980 * NOTE: currenty rtl8225 RF code changes basic rates, so we need to do 981 * this after rf init. 982 * TODO: try to find out whether RF code really needs to do this.. 983 */ 984 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8180) 985 rtl8180_conf_basic_rates(dev, 0x3); 986 else 987 rtl8180_conf_basic_rates(dev, 0x1f3); 988 989 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) 990 rtl8187se_set_antenna_config(dev, 991 priv->antenna_diversity_default, 992 priv->antenna_diversity_en); 993 return 0; 994 } 995 996 static int rtl8180_init_rx_ring(struct ieee80211_hw *dev) 997 { 998 struct rtl8180_priv *priv = dev->priv; 999 struct rtl818x_rx_cmd_desc *entry; 1000 int i; 1001 1002 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) 1003 priv->rx_ring_sz = sizeof(struct rtl8187se_rx_desc); 1004 else 1005 priv->rx_ring_sz = sizeof(struct rtl8180_rx_desc); 1006 1007 priv->rx_ring = pci_zalloc_consistent(priv->pdev, priv->rx_ring_sz * 32, 1008 &priv->rx_ring_dma); 1009 if (!priv->rx_ring || (unsigned long)priv->rx_ring & 0xFF) { 1010 wiphy_err(dev->wiphy, "Cannot allocate RX ring\n"); 1011 return -ENOMEM; 1012 } 1013 1014 priv->rx_idx = 0; 1015 1016 for (i = 0; i < 32; i++) { 1017 struct sk_buff *skb = dev_alloc_skb(MAX_RX_SIZE); 1018 dma_addr_t *mapping; 1019 entry = priv->rx_ring + priv->rx_ring_sz*i; 1020 if (!skb) { 1021 pci_free_consistent(priv->pdev, priv->rx_ring_sz * 32, 1022 priv->rx_ring, priv->rx_ring_dma); 1023 wiphy_err(dev->wiphy, "Cannot allocate RX skb\n"); 1024 return -ENOMEM; 1025 } 1026 priv->rx_buf[i] = skb; 1027 mapping = (dma_addr_t *)skb->cb; 1028 *mapping = pci_map_single(priv->pdev, skb_tail_pointer(skb), 1029 MAX_RX_SIZE, PCI_DMA_FROMDEVICE); 1030 1031 if (pci_dma_mapping_error(priv->pdev, *mapping)) { 1032 kfree_skb(skb); 1033 pci_free_consistent(priv->pdev, priv->rx_ring_sz * 32, 1034 priv->rx_ring, priv->rx_ring_dma); 1035 wiphy_err(dev->wiphy, "Cannot map DMA for RX skb\n"); 1036 return -ENOMEM; 1037 } 1038 1039 entry->rx_buf = cpu_to_le32(*mapping); 1040 entry->flags = cpu_to_le32(RTL818X_RX_DESC_FLAG_OWN | 1041 MAX_RX_SIZE); 1042 } 1043 entry->flags |= cpu_to_le32(RTL818X_RX_DESC_FLAG_EOR); 1044 return 0; 1045 } 1046 1047 static void rtl8180_free_rx_ring(struct ieee80211_hw *dev) 1048 { 1049 struct rtl8180_priv *priv = dev->priv; 1050 int i; 1051 1052 for (i = 0; i < 32; i++) { 1053 struct sk_buff *skb = priv->rx_buf[i]; 1054 if (!skb) 1055 continue; 1056 1057 pci_unmap_single(priv->pdev, 1058 *((dma_addr_t *)skb->cb), 1059 MAX_RX_SIZE, PCI_DMA_FROMDEVICE); 1060 kfree_skb(skb); 1061 } 1062 1063 pci_free_consistent(priv->pdev, priv->rx_ring_sz * 32, 1064 priv->rx_ring, priv->rx_ring_dma); 1065 priv->rx_ring = NULL; 1066 } 1067 1068 static int rtl8180_init_tx_ring(struct ieee80211_hw *dev, 1069 unsigned int prio, unsigned int entries) 1070 { 1071 struct rtl8180_priv *priv = dev->priv; 1072 struct rtl8180_tx_desc *ring; 1073 dma_addr_t dma; 1074 int i; 1075 1076 ring = pci_zalloc_consistent(priv->pdev, sizeof(*ring) * entries, 1077 &dma); 1078 if (!ring || (unsigned long)ring & 0xFF) { 1079 wiphy_err(dev->wiphy, "Cannot allocate TX ring (prio = %d)\n", 1080 prio); 1081 return -ENOMEM; 1082 } 1083 1084 priv->tx_ring[prio].desc = ring; 1085 priv->tx_ring[prio].dma = dma; 1086 priv->tx_ring[prio].idx = 0; 1087 priv->tx_ring[prio].entries = entries; 1088 skb_queue_head_init(&priv->tx_ring[prio].queue); 1089 1090 for (i = 0; i < entries; i++) 1091 ring[i].next_tx_desc = 1092 cpu_to_le32((u32)dma + ((i + 1) % entries) * sizeof(*ring)); 1093 1094 return 0; 1095 } 1096 1097 static void rtl8180_free_tx_ring(struct ieee80211_hw *dev, unsigned int prio) 1098 { 1099 struct rtl8180_priv *priv = dev->priv; 1100 struct rtl8180_tx_ring *ring = &priv->tx_ring[prio]; 1101 1102 while (skb_queue_len(&ring->queue)) { 1103 struct rtl8180_tx_desc *entry = &ring->desc[ring->idx]; 1104 struct sk_buff *skb = __skb_dequeue(&ring->queue); 1105 1106 pci_unmap_single(priv->pdev, le32_to_cpu(entry->tx_buf), 1107 skb->len, PCI_DMA_TODEVICE); 1108 kfree_skb(skb); 1109 ring->idx = (ring->idx + 1) % ring->entries; 1110 } 1111 1112 pci_free_consistent(priv->pdev, sizeof(*ring->desc)*ring->entries, 1113 ring->desc, ring->dma); 1114 ring->desc = NULL; 1115 } 1116 1117 static int rtl8180_start(struct ieee80211_hw *dev) 1118 { 1119 struct rtl8180_priv *priv = dev->priv; 1120 int ret, i; 1121 u32 reg; 1122 1123 ret = rtl8180_init_rx_ring(dev); 1124 if (ret) 1125 return ret; 1126 1127 for (i = 0; i < (dev->queues + 1); i++) 1128 if ((ret = rtl8180_init_tx_ring(dev, i, 16))) 1129 goto err_free_rings; 1130 1131 ret = rtl8180_init_hw(dev); 1132 if (ret) 1133 goto err_free_rings; 1134 1135 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { 1136 ret = request_irq(priv->pdev->irq, rtl8187se_interrupt, 1137 IRQF_SHARED, KBUILD_MODNAME, dev); 1138 } else { 1139 ret = request_irq(priv->pdev->irq, rtl8180_interrupt, 1140 IRQF_SHARED, KBUILD_MODNAME, dev); 1141 } 1142 1143 if (ret) { 1144 wiphy_err(dev->wiphy, "failed to register IRQ handler\n"); 1145 goto err_free_rings; 1146 } 1147 1148 rtl8180_int_enable(dev); 1149 1150 /* in rtl8187se at MAR regs offset there is the management 1151 * TX descriptor DMA addres.. 1152 */ 1153 if (priv->chip_family != RTL818X_CHIP_FAMILY_RTL8187SE) { 1154 rtl818x_iowrite32(priv, &priv->map->MAR[0], ~0); 1155 rtl818x_iowrite32(priv, &priv->map->MAR[1], ~0); 1156 } 1157 1158 reg = RTL818X_RX_CONF_ONLYERLPKT | 1159 RTL818X_RX_CONF_RX_AUTORESETPHY | 1160 RTL818X_RX_CONF_MGMT | 1161 RTL818X_RX_CONF_DATA | 1162 (7 << 8 /* MAX RX DMA */) | 1163 RTL818X_RX_CONF_BROADCAST | 1164 RTL818X_RX_CONF_NICMAC; 1165 1166 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8185) 1167 reg |= RTL818X_RX_CONF_CSDM1 | RTL818X_RX_CONF_CSDM2; 1168 else if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8180) { 1169 reg |= (priv->rfparam & RF_PARAM_CARRIERSENSE1) 1170 ? RTL818X_RX_CONF_CSDM1 : 0; 1171 reg |= (priv->rfparam & RF_PARAM_CARRIERSENSE2) 1172 ? RTL818X_RX_CONF_CSDM2 : 0; 1173 } else { 1174 reg &= ~(RTL818X_RX_CONF_CSDM1 | RTL818X_RX_CONF_CSDM2); 1175 } 1176 1177 priv->rx_conf = reg; 1178 rtl818x_iowrite32(priv, &priv->map->RX_CONF, reg); 1179 1180 if (priv->chip_family != RTL818X_CHIP_FAMILY_RTL8180) { 1181 reg = rtl818x_ioread8(priv, &priv->map->CW_CONF); 1182 1183 /* CW is not on per-packet basis. 1184 * in rtl8185 the CW_VALUE reg is used. 1185 * in rtl8187se the AC param regs are used. 1186 */ 1187 reg &= ~RTL818X_CW_CONF_PERPACKET_CW; 1188 /* retry limit IS on per-packet basis. 1189 * the short and long retry limit in TX_CONF 1190 * reg are ignored 1191 */ 1192 reg |= RTL818X_CW_CONF_PERPACKET_RETRY; 1193 rtl818x_iowrite8(priv, &priv->map->CW_CONF, reg); 1194 1195 reg = rtl818x_ioread8(priv, &priv->map->TX_AGC_CTL); 1196 /* TX antenna and TX gain are not on per-packet basis. 1197 * TX Antenna is selected by ANTSEL reg (RX in BB regs). 1198 * TX gain is selected with CCK_TX_AGC and OFDM_TX_AGC regs 1199 */ 1200 reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_GAIN; 1201 reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL; 1202 reg |= RTL818X_TX_AGC_CTL_FEEDBACK_ANT; 1203 rtl818x_iowrite8(priv, &priv->map->TX_AGC_CTL, reg); 1204 1205 /* disable early TX */ 1206 rtl818x_iowrite8(priv, (u8 __iomem *)priv->map + 0xec, 0x3f); 1207 } 1208 1209 reg = rtl818x_ioread32(priv, &priv->map->TX_CONF); 1210 reg |= (6 << 21 /* MAX TX DMA */) | 1211 RTL818X_TX_CONF_NO_ICV; 1212 1213 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) 1214 reg |= 1<<30; /* "duration procedure mode" */ 1215 1216 if (priv->chip_family != RTL818X_CHIP_FAMILY_RTL8180) 1217 reg &= ~RTL818X_TX_CONF_PROBE_DTS; 1218 else 1219 reg &= ~RTL818X_TX_CONF_HW_SEQNUM; 1220 1221 reg &= ~RTL818X_TX_CONF_DISCW; 1222 1223 /* different meaning, same value on both rtl8185 and rtl8180 */ 1224 reg &= ~RTL818X_TX_CONF_SAT_HWPLCP; 1225 1226 rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg); 1227 1228 reg = rtl818x_ioread8(priv, &priv->map->CMD); 1229 reg |= RTL818X_CMD_RX_ENABLE; 1230 reg |= RTL818X_CMD_TX_ENABLE; 1231 rtl818x_iowrite8(priv, &priv->map->CMD, reg); 1232 1233 return 0; 1234 1235 err_free_rings: 1236 rtl8180_free_rx_ring(dev); 1237 for (i = 0; i < (dev->queues + 1); i++) 1238 if (priv->tx_ring[i].desc) 1239 rtl8180_free_tx_ring(dev, i); 1240 1241 return ret; 1242 } 1243 1244 static void rtl8180_stop(struct ieee80211_hw *dev) 1245 { 1246 struct rtl8180_priv *priv = dev->priv; 1247 u8 reg; 1248 int i; 1249 1250 rtl8180_int_disable(dev); 1251 1252 reg = rtl818x_ioread8(priv, &priv->map->CMD); 1253 reg &= ~RTL818X_CMD_TX_ENABLE; 1254 reg &= ~RTL818X_CMD_RX_ENABLE; 1255 rtl818x_iowrite8(priv, &priv->map->CMD, reg); 1256 1257 priv->rf->stop(dev); 1258 1259 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); 1260 reg = rtl818x_ioread8(priv, &priv->map->CONFIG4); 1261 rtl818x_iowrite8(priv, &priv->map->CONFIG4, reg | RTL818X_CONFIG4_VCOOFF); 1262 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); 1263 1264 free_irq(priv->pdev->irq, dev); 1265 1266 rtl8180_free_rx_ring(dev); 1267 for (i = 0; i < (dev->queues + 1); i++) 1268 rtl8180_free_tx_ring(dev, i); 1269 } 1270 1271 static u64 rtl8180_get_tsf(struct ieee80211_hw *dev, 1272 struct ieee80211_vif *vif) 1273 { 1274 struct rtl8180_priv *priv = dev->priv; 1275 1276 return rtl818x_ioread32(priv, &priv->map->TSFT[0]) | 1277 (u64)(rtl818x_ioread32(priv, &priv->map->TSFT[1])) << 32; 1278 } 1279 1280 static void rtl8180_beacon_work(struct work_struct *work) 1281 { 1282 struct rtl8180_vif *vif_priv = 1283 container_of(work, struct rtl8180_vif, beacon_work.work); 1284 struct ieee80211_vif *vif = 1285 container_of((void *)vif_priv, struct ieee80211_vif, drv_priv); 1286 struct ieee80211_hw *dev = vif_priv->dev; 1287 struct ieee80211_mgmt *mgmt; 1288 struct sk_buff *skb; 1289 1290 /* don't overflow the tx ring */ 1291 if (ieee80211_queue_stopped(dev, 0)) 1292 goto resched; 1293 1294 /* grab a fresh beacon */ 1295 skb = ieee80211_beacon_get(dev, vif); 1296 if (!skb) 1297 goto resched; 1298 1299 /* 1300 * update beacon timestamp w/ TSF value 1301 * TODO: make hardware update beacon timestamp 1302 */ 1303 mgmt = (struct ieee80211_mgmt *)skb->data; 1304 mgmt->u.beacon.timestamp = cpu_to_le64(rtl8180_get_tsf(dev, vif)); 1305 1306 /* TODO: use actual beacon queue */ 1307 skb_set_queue_mapping(skb, 0); 1308 1309 rtl8180_tx(dev, NULL, skb); 1310 1311 resched: 1312 /* 1313 * schedule next beacon 1314 * TODO: use hardware support for beacon timing 1315 */ 1316 schedule_delayed_work(&vif_priv->beacon_work, 1317 usecs_to_jiffies(1024 * vif->bss_conf.beacon_int)); 1318 } 1319 1320 static int rtl8180_add_interface(struct ieee80211_hw *dev, 1321 struct ieee80211_vif *vif) 1322 { 1323 struct rtl8180_priv *priv = dev->priv; 1324 struct rtl8180_vif *vif_priv; 1325 1326 /* 1327 * We only support one active interface at a time. 1328 */ 1329 if (priv->vif) 1330 return -EBUSY; 1331 1332 switch (vif->type) { 1333 case NL80211_IFTYPE_STATION: 1334 case NL80211_IFTYPE_ADHOC: 1335 break; 1336 default: 1337 return -EOPNOTSUPP; 1338 } 1339 1340 priv->vif = vif; 1341 1342 /* Initialize driver private area */ 1343 vif_priv = (struct rtl8180_vif *)&vif->drv_priv; 1344 vif_priv->dev = dev; 1345 INIT_DELAYED_WORK(&vif_priv->beacon_work, rtl8180_beacon_work); 1346 vif_priv->enable_beacon = false; 1347 1348 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); 1349 rtl818x_iowrite32(priv, (__le32 __iomem *)&priv->map->MAC[0], 1350 le32_to_cpu(*(__le32 *)vif->addr)); 1351 rtl818x_iowrite16(priv, (__le16 __iomem *)&priv->map->MAC[4], 1352 le16_to_cpu(*(__le16 *)(vif->addr + 4))); 1353 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); 1354 1355 return 0; 1356 } 1357 1358 static void rtl8180_remove_interface(struct ieee80211_hw *dev, 1359 struct ieee80211_vif *vif) 1360 { 1361 struct rtl8180_priv *priv = dev->priv; 1362 priv->vif = NULL; 1363 } 1364 1365 static int rtl8180_config(struct ieee80211_hw *dev, u32 changed) 1366 { 1367 struct rtl8180_priv *priv = dev->priv; 1368 struct ieee80211_conf *conf = &dev->conf; 1369 1370 priv->rf->set_chan(dev, conf); 1371 1372 return 0; 1373 } 1374 1375 static void rtl8187se_conf_ac_parm(struct ieee80211_hw *dev, u8 queue) 1376 { 1377 const struct ieee80211_tx_queue_params *params; 1378 struct rtl8180_priv *priv = dev->priv; 1379 1380 /* hw value */ 1381 u32 ac_param; 1382 1383 u8 aifs; 1384 u8 txop; 1385 u8 cw_min, cw_max; 1386 1387 params = &priv->queue_param[queue]; 1388 1389 cw_min = fls(params->cw_min); 1390 cw_max = fls(params->cw_max); 1391 1392 aifs = 10 + params->aifs * priv->slot_time; 1393 1394 /* TODO: check if txop HW is in us (mult by 32) */ 1395 txop = params->txop; 1396 1397 ac_param = txop << AC_PARAM_TXOP_LIMIT_SHIFT | 1398 cw_max << AC_PARAM_ECW_MAX_SHIFT | 1399 cw_min << AC_PARAM_ECW_MIN_SHIFT | 1400 aifs << AC_PARAM_AIFS_SHIFT; 1401 1402 switch (queue) { 1403 case IEEE80211_AC_BK: 1404 rtl818x_iowrite32(priv, &priv->map->AC_BK_PARAM, ac_param); 1405 break; 1406 case IEEE80211_AC_BE: 1407 rtl818x_iowrite32(priv, &priv->map->AC_BE_PARAM, ac_param); 1408 break; 1409 case IEEE80211_AC_VI: 1410 rtl818x_iowrite32(priv, &priv->map->AC_VI_PARAM, ac_param); 1411 break; 1412 case IEEE80211_AC_VO: 1413 rtl818x_iowrite32(priv, &priv->map->AC_VO_PARAM, ac_param); 1414 break; 1415 } 1416 } 1417 1418 static int rtl8180_conf_tx(struct ieee80211_hw *dev, 1419 struct ieee80211_vif *vif, u16 queue, 1420 const struct ieee80211_tx_queue_params *params) 1421 { 1422 struct rtl8180_priv *priv = dev->priv; 1423 u8 cw_min, cw_max; 1424 1425 /* nothing to do ? */ 1426 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8180) 1427 return 0; 1428 1429 cw_min = fls(params->cw_min); 1430 cw_max = fls(params->cw_max); 1431 1432 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { 1433 priv->queue_param[queue] = *params; 1434 rtl8187se_conf_ac_parm(dev, queue); 1435 } else 1436 rtl818x_iowrite8(priv, &priv->map->CW_VAL, 1437 (cw_max << 4) | cw_min); 1438 return 0; 1439 } 1440 1441 static void rtl8180_conf_erp(struct ieee80211_hw *dev, 1442 struct ieee80211_bss_conf *info) 1443 { 1444 struct rtl8180_priv *priv = dev->priv; 1445 u8 sifs, difs; 1446 int eifs; 1447 u8 hw_eifs; 1448 1449 /* TODO: should we do something ? */ 1450 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8180) 1451 return; 1452 1453 /* I _hope_ this means 10uS for the HW. 1454 * In reference code it is 0x22 for 1455 * both rtl8187L and rtl8187SE 1456 */ 1457 sifs = 0x22; 1458 1459 if (info->use_short_slot) 1460 priv->slot_time = 9; 1461 else 1462 priv->slot_time = 20; 1463 1464 /* 10 is SIFS time in uS */ 1465 difs = 10 + 2 * priv->slot_time; 1466 eifs = 10 + difs + priv->ack_time; 1467 1468 /* HW should use 4uS units for EIFS (I'm sure for rtl8185)*/ 1469 hw_eifs = DIV_ROUND_UP(eifs, 4); 1470 1471 1472 rtl818x_iowrite8(priv, &priv->map->SLOT, priv->slot_time); 1473 rtl818x_iowrite8(priv, &priv->map->SIFS, sifs); 1474 rtl818x_iowrite8(priv, &priv->map->DIFS, difs); 1475 1476 /* from reference code. set ack timeout reg = eifs reg */ 1477 rtl818x_iowrite8(priv, &priv->map->CARRIER_SENSE_COUNTER, hw_eifs); 1478 1479 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) 1480 rtl818x_iowrite8(priv, &priv->map->EIFS_8187SE, hw_eifs); 1481 else if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8185) { 1482 /* rtl8187/rtl8185 HW bug. After EIFS is elapsed, 1483 * the HW still wait for DIFS. 1484 * HW uses 4uS units for EIFS. 1485 */ 1486 hw_eifs = DIV_ROUND_UP(eifs - difs, 4); 1487 1488 rtl818x_iowrite8(priv, &priv->map->EIFS, hw_eifs); 1489 } 1490 } 1491 1492 static void rtl8180_bss_info_changed(struct ieee80211_hw *dev, 1493 struct ieee80211_vif *vif, 1494 struct ieee80211_bss_conf *info, 1495 u32 changed) 1496 { 1497 struct rtl8180_priv *priv = dev->priv; 1498 struct rtl8180_vif *vif_priv; 1499 int i; 1500 u8 reg; 1501 1502 vif_priv = (struct rtl8180_vif *)&vif->drv_priv; 1503 1504 if (changed & BSS_CHANGED_BSSID) { 1505 rtl818x_iowrite16(priv, (__le16 __iomem *)&priv->map->BSSID[0], 1506 le16_to_cpu(*(__le16 *)info->bssid)); 1507 rtl818x_iowrite32(priv, (__le32 __iomem *)&priv->map->BSSID[2], 1508 le32_to_cpu(*(__le32 *)(info->bssid + 2))); 1509 1510 if (is_valid_ether_addr(info->bssid)) { 1511 if (vif->type == NL80211_IFTYPE_ADHOC) 1512 reg = RTL818X_MSR_ADHOC; 1513 else 1514 reg = RTL818X_MSR_INFRA; 1515 } else 1516 reg = RTL818X_MSR_NO_LINK; 1517 1518 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) 1519 reg |= RTL818X_MSR_ENEDCA; 1520 1521 rtl818x_iowrite8(priv, &priv->map->MSR, reg); 1522 } 1523 1524 if (changed & BSS_CHANGED_BASIC_RATES) 1525 rtl8180_conf_basic_rates(dev, info->basic_rates); 1526 1527 if (changed & (BSS_CHANGED_ERP_SLOT | BSS_CHANGED_ERP_PREAMBLE)) { 1528 1529 /* when preamble changes, acktime duration changes, and erp must 1530 * be recalculated. ACK time is calculated at lowest rate. 1531 * Since mac80211 include SIFS time we remove it (-10) 1532 */ 1533 priv->ack_time = 1534 le16_to_cpu(ieee80211_generic_frame_duration(dev, 1535 priv->vif, 1536 NL80211_BAND_2GHZ, 10, 1537 &priv->rates[0])) - 10; 1538 1539 rtl8180_conf_erp(dev, info); 1540 1541 /* mac80211 supplies aifs_n to driver and calls 1542 * conf_tx callback whether aifs_n changes, NOT 1543 * when aifs changes. 1544 * Aifs should be recalculated if slot changes. 1545 */ 1546 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { 1547 for (i = 0; i < 4; i++) 1548 rtl8187se_conf_ac_parm(dev, i); 1549 } 1550 } 1551 1552 if (changed & BSS_CHANGED_BEACON_ENABLED) 1553 vif_priv->enable_beacon = info->enable_beacon; 1554 1555 if (changed & (BSS_CHANGED_BEACON_ENABLED | BSS_CHANGED_BEACON)) { 1556 cancel_delayed_work_sync(&vif_priv->beacon_work); 1557 if (vif_priv->enable_beacon) 1558 schedule_work(&vif_priv->beacon_work.work); 1559 } 1560 } 1561 1562 static u64 rtl8180_prepare_multicast(struct ieee80211_hw *dev, 1563 struct netdev_hw_addr_list *mc_list) 1564 { 1565 return netdev_hw_addr_list_count(mc_list); 1566 } 1567 1568 static void rtl8180_configure_filter(struct ieee80211_hw *dev, 1569 unsigned int changed_flags, 1570 unsigned int *total_flags, 1571 u64 multicast) 1572 { 1573 struct rtl8180_priv *priv = dev->priv; 1574 1575 if (changed_flags & FIF_FCSFAIL) 1576 priv->rx_conf ^= RTL818X_RX_CONF_FCS; 1577 if (changed_flags & FIF_CONTROL) 1578 priv->rx_conf ^= RTL818X_RX_CONF_CTRL; 1579 if (changed_flags & FIF_OTHER_BSS) 1580 priv->rx_conf ^= RTL818X_RX_CONF_MONITOR; 1581 if (*total_flags & FIF_ALLMULTI || multicast > 0) 1582 priv->rx_conf |= RTL818X_RX_CONF_MULTICAST; 1583 else 1584 priv->rx_conf &= ~RTL818X_RX_CONF_MULTICAST; 1585 1586 *total_flags = 0; 1587 1588 if (priv->rx_conf & RTL818X_RX_CONF_FCS) 1589 *total_flags |= FIF_FCSFAIL; 1590 if (priv->rx_conf & RTL818X_RX_CONF_CTRL) 1591 *total_flags |= FIF_CONTROL; 1592 if (priv->rx_conf & RTL818X_RX_CONF_MONITOR) 1593 *total_flags |= FIF_OTHER_BSS; 1594 if (priv->rx_conf & RTL818X_RX_CONF_MULTICAST) 1595 *total_flags |= FIF_ALLMULTI; 1596 1597 rtl818x_iowrite32(priv, &priv->map->RX_CONF, priv->rx_conf); 1598 } 1599 1600 static const struct ieee80211_ops rtl8180_ops = { 1601 .tx = rtl8180_tx, 1602 .start = rtl8180_start, 1603 .stop = rtl8180_stop, 1604 .add_interface = rtl8180_add_interface, 1605 .remove_interface = rtl8180_remove_interface, 1606 .config = rtl8180_config, 1607 .bss_info_changed = rtl8180_bss_info_changed, 1608 .conf_tx = rtl8180_conf_tx, 1609 .prepare_multicast = rtl8180_prepare_multicast, 1610 .configure_filter = rtl8180_configure_filter, 1611 .get_tsf = rtl8180_get_tsf, 1612 }; 1613 1614 static void rtl8180_eeprom_register_read(struct eeprom_93cx6 *eeprom) 1615 { 1616 struct rtl8180_priv *priv = eeprom->data; 1617 u8 reg = rtl818x_ioread8(priv, &priv->map->EEPROM_CMD); 1618 1619 eeprom->reg_data_in = reg & RTL818X_EEPROM_CMD_WRITE; 1620 eeprom->reg_data_out = reg & RTL818X_EEPROM_CMD_READ; 1621 eeprom->reg_data_clock = reg & RTL818X_EEPROM_CMD_CK; 1622 eeprom->reg_chip_select = reg & RTL818X_EEPROM_CMD_CS; 1623 } 1624 1625 static void rtl8180_eeprom_register_write(struct eeprom_93cx6 *eeprom) 1626 { 1627 struct rtl8180_priv *priv = eeprom->data; 1628 u8 reg = 2 << 6; 1629 1630 if (eeprom->reg_data_in) 1631 reg |= RTL818X_EEPROM_CMD_WRITE; 1632 if (eeprom->reg_data_out) 1633 reg |= RTL818X_EEPROM_CMD_READ; 1634 if (eeprom->reg_data_clock) 1635 reg |= RTL818X_EEPROM_CMD_CK; 1636 if (eeprom->reg_chip_select) 1637 reg |= RTL818X_EEPROM_CMD_CS; 1638 1639 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, reg); 1640 rtl818x_ioread8(priv, &priv->map->EEPROM_CMD); 1641 udelay(10); 1642 } 1643 1644 static void rtl8180_eeprom_read(struct rtl8180_priv *priv) 1645 { 1646 struct eeprom_93cx6 eeprom; 1647 int eeprom_cck_table_adr; 1648 u16 eeprom_val; 1649 int i; 1650 1651 eeprom.data = priv; 1652 eeprom.register_read = rtl8180_eeprom_register_read; 1653 eeprom.register_write = rtl8180_eeprom_register_write; 1654 if (rtl818x_ioread32(priv, &priv->map->RX_CONF) & (1 << 6)) 1655 eeprom.width = PCI_EEPROM_WIDTH_93C66; 1656 else 1657 eeprom.width = PCI_EEPROM_WIDTH_93C46; 1658 1659 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, 1660 RTL818X_EEPROM_CMD_PROGRAM); 1661 rtl818x_ioread8(priv, &priv->map->EEPROM_CMD); 1662 udelay(10); 1663 1664 eeprom_93cx6_read(&eeprom, 0x06, &eeprom_val); 1665 eeprom_val &= 0xFF; 1666 priv->rf_type = eeprom_val; 1667 1668 eeprom_93cx6_read(&eeprom, 0x17, &eeprom_val); 1669 priv->csthreshold = eeprom_val >> 8; 1670 1671 eeprom_93cx6_multiread(&eeprom, 0x7, (__le16 *)priv->mac_addr, 3); 1672 1673 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) 1674 eeprom_cck_table_adr = 0x30; 1675 else 1676 eeprom_cck_table_adr = 0x10; 1677 1678 /* CCK TX power */ 1679 for (i = 0; i < 14; i += 2) { 1680 u16 txpwr; 1681 eeprom_93cx6_read(&eeprom, eeprom_cck_table_adr + (i >> 1), 1682 &txpwr); 1683 priv->channels[i].hw_value = txpwr & 0xFF; 1684 priv->channels[i + 1].hw_value = txpwr >> 8; 1685 } 1686 1687 /* OFDM TX power */ 1688 if (priv->chip_family != RTL818X_CHIP_FAMILY_RTL8180) { 1689 for (i = 0; i < 14; i += 2) { 1690 u16 txpwr; 1691 eeprom_93cx6_read(&eeprom, 0x20 + (i >> 1), &txpwr); 1692 priv->channels[i].hw_value |= (txpwr & 0xFF) << 8; 1693 priv->channels[i + 1].hw_value |= txpwr & 0xFF00; 1694 } 1695 } 1696 1697 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8180) { 1698 __le32 anaparam; 1699 eeprom_93cx6_multiread(&eeprom, 0xD, (__le16 *)&anaparam, 2); 1700 priv->anaparam = le32_to_cpu(anaparam); 1701 eeprom_93cx6_read(&eeprom, 0x19, &priv->rfparam); 1702 } 1703 1704 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { 1705 eeprom_93cx6_read(&eeprom, 0x3F, &eeprom_val); 1706 priv->antenna_diversity_en = !!(eeprom_val & 0x100); 1707 priv->antenna_diversity_default = (eeprom_val & 0xC00) == 0x400; 1708 1709 eeprom_93cx6_read(&eeprom, 0x7C, &eeprom_val); 1710 priv->xtal_out = eeprom_val & 0xF; 1711 priv->xtal_in = (eeprom_val & 0xF0) >> 4; 1712 priv->xtal_cal = !!(eeprom_val & 0x1000); 1713 priv->thermal_meter_val = (eeprom_val & 0xF00) >> 8; 1714 priv->thermal_meter_en = !!(eeprom_val & 0x2000); 1715 } 1716 1717 rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, 1718 RTL818X_EEPROM_CMD_NORMAL); 1719 } 1720 1721 static int rtl8180_probe(struct pci_dev *pdev, 1722 const struct pci_device_id *id) 1723 { 1724 struct ieee80211_hw *dev; 1725 struct rtl8180_priv *priv; 1726 unsigned long mem_len; 1727 unsigned int io_len; 1728 int err; 1729 const char *chip_name, *rf_name = NULL; 1730 u32 reg; 1731 1732 err = pci_enable_device(pdev); 1733 if (err) { 1734 printk(KERN_ERR "%s (rtl8180): Cannot enable new PCI device\n", 1735 pci_name(pdev)); 1736 return err; 1737 } 1738 1739 err = pci_request_regions(pdev, KBUILD_MODNAME); 1740 if (err) { 1741 printk(KERN_ERR "%s (rtl8180): Cannot obtain PCI resources\n", 1742 pci_name(pdev)); 1743 goto err_disable_dev; 1744 } 1745 1746 io_len = pci_resource_len(pdev, 0); 1747 mem_len = pci_resource_len(pdev, 1); 1748 1749 if (mem_len < sizeof(struct rtl818x_csr) || 1750 io_len < sizeof(struct rtl818x_csr)) { 1751 printk(KERN_ERR "%s (rtl8180): Too short PCI resources\n", 1752 pci_name(pdev)); 1753 err = -ENOMEM; 1754 goto err_free_reg; 1755 } 1756 1757 if ((err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) || 1758 (err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32)))) { 1759 printk(KERN_ERR "%s (rtl8180): No suitable DMA available\n", 1760 pci_name(pdev)); 1761 goto err_free_reg; 1762 } 1763 1764 pci_set_master(pdev); 1765 1766 dev = ieee80211_alloc_hw(sizeof(*priv), &rtl8180_ops); 1767 if (!dev) { 1768 printk(KERN_ERR "%s (rtl8180): ieee80211 alloc failed\n", 1769 pci_name(pdev)); 1770 err = -ENOMEM; 1771 goto err_free_reg; 1772 } 1773 1774 priv = dev->priv; 1775 priv->pdev = pdev; 1776 1777 dev->max_rates = 1; 1778 SET_IEEE80211_DEV(dev, &pdev->dev); 1779 pci_set_drvdata(pdev, dev); 1780 1781 priv->map_pio = false; 1782 priv->map = pci_iomap(pdev, 1, mem_len); 1783 if (!priv->map) { 1784 priv->map = pci_iomap(pdev, 0, io_len); 1785 priv->map_pio = true; 1786 } 1787 1788 if (!priv->map) { 1789 dev_err(&pdev->dev, "Cannot map device memory/PIO\n"); 1790 err = -ENOMEM; 1791 goto err_free_dev; 1792 } 1793 1794 BUILD_BUG_ON(sizeof(priv->channels) != sizeof(rtl818x_channels)); 1795 BUILD_BUG_ON(sizeof(priv->rates) != sizeof(rtl818x_rates)); 1796 1797 memcpy(priv->channels, rtl818x_channels, sizeof(rtl818x_channels)); 1798 memcpy(priv->rates, rtl818x_rates, sizeof(rtl818x_rates)); 1799 1800 priv->band.band = NL80211_BAND_2GHZ; 1801 priv->band.channels = priv->channels; 1802 priv->band.n_channels = ARRAY_SIZE(rtl818x_channels); 1803 priv->band.bitrates = priv->rates; 1804 priv->band.n_bitrates = 4; 1805 dev->wiphy->bands[NL80211_BAND_2GHZ] = &priv->band; 1806 1807 ieee80211_hw_set(dev, HOST_BROADCAST_PS_BUFFERING); 1808 ieee80211_hw_set(dev, RX_INCLUDES_FCS); 1809 1810 dev->vif_data_size = sizeof(struct rtl8180_vif); 1811 dev->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION) | 1812 BIT(NL80211_IFTYPE_ADHOC); 1813 dev->max_signal = 65; 1814 1815 reg = rtl818x_ioread32(priv, &priv->map->TX_CONF); 1816 reg &= RTL818X_TX_CONF_HWVER_MASK; 1817 switch (reg) { 1818 case RTL818X_TX_CONF_R8180_ABCD: 1819 chip_name = "RTL8180"; 1820 priv->chip_family = RTL818X_CHIP_FAMILY_RTL8180; 1821 break; 1822 1823 case RTL818X_TX_CONF_R8180_F: 1824 chip_name = "RTL8180vF"; 1825 priv->chip_family = RTL818X_CHIP_FAMILY_RTL8180; 1826 break; 1827 1828 case RTL818X_TX_CONF_R8185_ABC: 1829 chip_name = "RTL8185"; 1830 priv->chip_family = RTL818X_CHIP_FAMILY_RTL8185; 1831 break; 1832 1833 case RTL818X_TX_CONF_R8185_D: 1834 chip_name = "RTL8185vD"; 1835 priv->chip_family = RTL818X_CHIP_FAMILY_RTL8185; 1836 break; 1837 1838 case RTL818X_TX_CONF_RTL8187SE: 1839 chip_name = "RTL8187SE"; 1840 if (priv->map_pio) { 1841 dev_err(&pdev->dev, 1842 "MMIO failed. PIO not supported on RTL8187SE\n"); 1843 err = -ENOMEM; 1844 goto err_iounmap; 1845 } 1846 priv->chip_family = RTL818X_CHIP_FAMILY_RTL8187SE; 1847 break; 1848 1849 default: 1850 printk(KERN_ERR "%s (rtl8180): Unknown chip! (0x%x)\n", 1851 pci_name(pdev), reg >> 25); 1852 err = -ENODEV; 1853 goto err_iounmap; 1854 } 1855 1856 /* we declare to MAC80211 all the queues except for beacon queue 1857 * that will be eventually handled by DRV. 1858 * TX rings are arranged in such a way that lower is the IDX, 1859 * higher is the priority, in order to achieve direct mapping 1860 * with mac80211, however the beacon queue is an exception and it 1861 * is mapped on the highst tx ring IDX. 1862 */ 1863 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) 1864 dev->queues = RTL8187SE_NR_TX_QUEUES - 1; 1865 else 1866 dev->queues = RTL8180_NR_TX_QUEUES - 1; 1867 1868 if (priv->chip_family != RTL818X_CHIP_FAMILY_RTL8180) { 1869 priv->band.n_bitrates = ARRAY_SIZE(rtl818x_rates); 1870 pci_try_set_mwi(pdev); 1871 } 1872 1873 if (priv->chip_family != RTL818X_CHIP_FAMILY_RTL8180) 1874 ieee80211_hw_set(dev, SIGNAL_DBM); 1875 else 1876 ieee80211_hw_set(dev, SIGNAL_UNSPEC); 1877 1878 wiphy_ext_feature_set(dev->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST); 1879 1880 rtl8180_eeprom_read(priv); 1881 1882 switch (priv->rf_type) { 1883 case 1: rf_name = "Intersil"; 1884 break; 1885 case 2: rf_name = "RFMD"; 1886 break; 1887 case 3: priv->rf = &sa2400_rf_ops; 1888 break; 1889 case 4: priv->rf = &max2820_rf_ops; 1890 break; 1891 case 5: priv->rf = &grf5101_rf_ops; 1892 break; 1893 case 9: 1894 if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) 1895 priv->rf = rtl8187se_detect_rf(dev); 1896 else 1897 priv->rf = rtl8180_detect_rf(dev); 1898 break; 1899 case 10: 1900 rf_name = "RTL8255"; 1901 break; 1902 default: 1903 printk(KERN_ERR "%s (rtl8180): Unknown RF! (0x%x)\n", 1904 pci_name(pdev), priv->rf_type); 1905 err = -ENODEV; 1906 goto err_iounmap; 1907 } 1908 1909 if (!priv->rf) { 1910 printk(KERN_ERR "%s (rtl8180): %s RF frontend not supported!\n", 1911 pci_name(pdev), rf_name); 1912 err = -ENODEV; 1913 goto err_iounmap; 1914 } 1915 1916 if (!is_valid_ether_addr(priv->mac_addr)) { 1917 printk(KERN_WARNING "%s (rtl8180): Invalid hwaddr! Using" 1918 " randomly generated MAC addr\n", pci_name(pdev)); 1919 eth_random_addr(priv->mac_addr); 1920 } 1921 SET_IEEE80211_PERM_ADDR(dev, priv->mac_addr); 1922 1923 spin_lock_init(&priv->lock); 1924 1925 err = ieee80211_register_hw(dev); 1926 if (err) { 1927 printk(KERN_ERR "%s (rtl8180): Cannot register device\n", 1928 pci_name(pdev)); 1929 goto err_iounmap; 1930 } 1931 1932 wiphy_info(dev->wiphy, "hwaddr %pm, %s + %s\n", 1933 priv->mac_addr, chip_name, priv->rf->name); 1934 1935 return 0; 1936 1937 err_iounmap: 1938 pci_iounmap(pdev, priv->map); 1939 1940 err_free_dev: 1941 ieee80211_free_hw(dev); 1942 1943 err_free_reg: 1944 pci_release_regions(pdev); 1945 1946 err_disable_dev: 1947 pci_disable_device(pdev); 1948 return err; 1949 } 1950 1951 static void rtl8180_remove(struct pci_dev *pdev) 1952 { 1953 struct ieee80211_hw *dev = pci_get_drvdata(pdev); 1954 struct rtl8180_priv *priv; 1955 1956 if (!dev) 1957 return; 1958 1959 ieee80211_unregister_hw(dev); 1960 1961 priv = dev->priv; 1962 1963 pci_iounmap(pdev, priv->map); 1964 pci_release_regions(pdev); 1965 pci_disable_device(pdev); 1966 ieee80211_free_hw(dev); 1967 } 1968 1969 #ifdef CONFIG_PM 1970 static int rtl8180_suspend(struct pci_dev *pdev, pm_message_t state) 1971 { 1972 pci_save_state(pdev); 1973 pci_set_power_state(pdev, pci_choose_state(pdev, state)); 1974 return 0; 1975 } 1976 1977 static int rtl8180_resume(struct pci_dev *pdev) 1978 { 1979 pci_set_power_state(pdev, PCI_D0); 1980 pci_restore_state(pdev); 1981 return 0; 1982 } 1983 1984 #endif /* CONFIG_PM */ 1985 1986 static struct pci_driver rtl8180_driver = { 1987 .name = KBUILD_MODNAME, 1988 .id_table = rtl8180_table, 1989 .probe = rtl8180_probe, 1990 .remove = rtl8180_remove, 1991 #ifdef CONFIG_PM 1992 .suspend = rtl8180_suspend, 1993 .resume = rtl8180_resume, 1994 #endif /* CONFIG_PM */ 1995 }; 1996 1997 module_pci_driver(rtl8180_driver); 1998