1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Copyright (c) 2012 - 2018 Microchip Technology Inc., and its subsidiaries. 4 * All rights reserved. 5 */ 6 7 #include <linux/clk.h> 8 #include <linux/spi/spi.h> 9 #include <linux/crc7.h> 10 #include <linux/crc-itu-t.h> 11 #include <linux/gpio/consumer.h> 12 13 #include "netdev.h" 14 #include "cfg80211.h" 15 16 #define SPI_MODALIAS "wilc1000_spi" 17 18 static bool enable_crc7; /* protect SPI commands with CRC7 */ 19 module_param(enable_crc7, bool, 0644); 20 MODULE_PARM_DESC(enable_crc7, 21 "Enable CRC7 checksum to protect command transfers\n" 22 "\t\t\tagainst corruption during the SPI transfer.\n" 23 "\t\t\tCommand transfers are short and the CPU-cycle cost\n" 24 "\t\t\tof enabling this is small."); 25 26 static bool enable_crc16; /* protect SPI data with CRC16 */ 27 module_param(enable_crc16, bool, 0644); 28 MODULE_PARM_DESC(enable_crc16, 29 "Enable CRC16 checksum to protect data transfers\n" 30 "\t\t\tagainst corruption during the SPI transfer.\n" 31 "\t\t\tData transfers can be large and the CPU-cycle cost\n" 32 "\t\t\tof enabling this may be substantial."); 33 34 /* 35 * For CMD_SINGLE_READ and CMD_INTERNAL_READ, WILC may insert one or 36 * more zero bytes between the command response and the DATA Start tag 37 * (0xf3). This behavior appears to be undocumented in "ATWILC1000 38 * USER GUIDE" (https://tinyurl.com/4hhshdts) but we have observed 1-4 39 * zero bytes when the SPI bus operates at 48MHz and none when it 40 * operates at 1MHz. 41 */ 42 #define WILC_SPI_RSP_HDR_EXTRA_DATA 8 43 44 struct wilc_spi { 45 bool isinit; /* true if SPI protocol has been configured */ 46 bool probing_crc; /* true if we're probing chip's CRC config */ 47 bool crc7_enabled; /* true if crc7 is currently enabled */ 48 bool crc16_enabled; /* true if crc16 is currently enabled */ 49 struct wilc_gpios { 50 struct gpio_desc *enable; /* ENABLE GPIO or NULL */ 51 struct gpio_desc *reset; /* RESET GPIO or NULL */ 52 } gpios; 53 }; 54 55 static const struct wilc_hif_func wilc_hif_spi; 56 57 static int wilc_spi_reset(struct wilc *wilc); 58 59 /******************************************** 60 * 61 * Spi protocol Function 62 * 63 ********************************************/ 64 65 #define CMD_DMA_WRITE 0xc1 66 #define CMD_DMA_READ 0xc2 67 #define CMD_INTERNAL_WRITE 0xc3 68 #define CMD_INTERNAL_READ 0xc4 69 #define CMD_TERMINATE 0xc5 70 #define CMD_REPEAT 0xc6 71 #define CMD_DMA_EXT_WRITE 0xc7 72 #define CMD_DMA_EXT_READ 0xc8 73 #define CMD_SINGLE_WRITE 0xc9 74 #define CMD_SINGLE_READ 0xca 75 #define CMD_RESET 0xcf 76 77 #define SPI_RETRY_MAX_LIMIT 10 78 #define SPI_ENABLE_VMM_RETRY_LIMIT 2 79 80 /* SPI response fields (section 11.1.2 in ATWILC1000 User Guide): */ 81 #define RSP_START_FIELD GENMASK(7, 4) 82 #define RSP_TYPE_FIELD GENMASK(3, 0) 83 84 /* SPI response values for the response fields: */ 85 #define RSP_START_TAG 0xc 86 #define RSP_TYPE_FIRST_PACKET 0x1 87 #define RSP_TYPE_INNER_PACKET 0x2 88 #define RSP_TYPE_LAST_PACKET 0x3 89 #define RSP_STATE_NO_ERROR 0x00 90 91 #define PROTOCOL_REG_PKT_SZ_MASK GENMASK(6, 4) 92 #define PROTOCOL_REG_CRC16_MASK GENMASK(3, 3) 93 #define PROTOCOL_REG_CRC7_MASK GENMASK(2, 2) 94 95 /* 96 * The SPI data packet size may be any integer power of two in the 97 * range from 256 to 8192 bytes. 98 */ 99 #define DATA_PKT_LOG_SZ_MIN 8 /* 256 B */ 100 #define DATA_PKT_LOG_SZ_MAX 13 /* 8 KiB */ 101 102 /* 103 * Select the data packet size (log2 of number of bytes): Use the 104 * maximum data packet size. We only retransmit complete packets, so 105 * there is no benefit from using smaller data packets. 106 */ 107 #define DATA_PKT_LOG_SZ DATA_PKT_LOG_SZ_MAX 108 #define DATA_PKT_SZ (1 << DATA_PKT_LOG_SZ) 109 110 #define WILC_SPI_COMMAND_STAT_SUCCESS 0 111 #define WILC_GET_RESP_HDR_START(h) (((h) >> 4) & 0xf) 112 113 struct wilc_spi_cmd { 114 u8 cmd_type; 115 union { 116 struct { 117 u8 addr[3]; 118 u8 crc[]; 119 } __packed simple_cmd; 120 struct { 121 u8 addr[3]; 122 u8 size[2]; 123 u8 crc[]; 124 } __packed dma_cmd; 125 struct { 126 u8 addr[3]; 127 u8 size[3]; 128 u8 crc[]; 129 } __packed dma_cmd_ext; 130 struct { 131 u8 addr[2]; 132 __be32 data; 133 u8 crc[]; 134 } __packed internal_w_cmd; 135 struct { 136 u8 addr[3]; 137 __be32 data; 138 u8 crc[]; 139 } __packed w_cmd; 140 } u; 141 } __packed; 142 143 struct wilc_spi_read_rsp_data { 144 u8 header; 145 u8 data[4]; 146 u8 crc[]; 147 } __packed; 148 149 struct wilc_spi_rsp_data { 150 u8 rsp_cmd_type; 151 u8 status; 152 u8 data[]; 153 } __packed; 154 155 struct wilc_spi_special_cmd_rsp { 156 u8 skip_byte; 157 u8 rsp_cmd_type; 158 u8 status; 159 } __packed; 160 161 static int wilc_parse_gpios(struct wilc *wilc) 162 { 163 struct spi_device *spi = to_spi_device(wilc->dev); 164 struct wilc_spi *spi_priv = wilc->bus_data; 165 struct wilc_gpios *gpios = &spi_priv->gpios; 166 167 /* get ENABLE pin and deassert it (if it is defined): */ 168 gpios->enable = devm_gpiod_get_optional(&spi->dev, 169 "enable", GPIOD_OUT_LOW); 170 /* get RESET pin and assert it (if it is defined): */ 171 if (gpios->enable) { 172 /* if enable pin exists, reset must exist as well */ 173 gpios->reset = devm_gpiod_get(&spi->dev, 174 "reset", GPIOD_OUT_HIGH); 175 if (IS_ERR(gpios->reset)) { 176 dev_err(&spi->dev, "missing reset gpio.\n"); 177 return PTR_ERR(gpios->reset); 178 } 179 } else { 180 gpios->reset = devm_gpiod_get_optional(&spi->dev, 181 "reset", GPIOD_OUT_HIGH); 182 } 183 return 0; 184 } 185 186 static void wilc_wlan_power(struct wilc *wilc, bool on) 187 { 188 struct wilc_spi *spi_priv = wilc->bus_data; 189 struct wilc_gpios *gpios = &spi_priv->gpios; 190 191 if (on) { 192 /* assert ENABLE: */ 193 gpiod_set_value(gpios->enable, 1); 194 mdelay(5); 195 /* deassert RESET: */ 196 gpiod_set_value(gpios->reset, 0); 197 } else { 198 /* assert RESET: */ 199 gpiod_set_value(gpios->reset, 1); 200 /* deassert ENABLE: */ 201 gpiod_set_value(gpios->enable, 0); 202 } 203 } 204 205 static int wilc_bus_probe(struct spi_device *spi) 206 { 207 int ret; 208 struct wilc *wilc; 209 struct wilc_spi *spi_priv; 210 211 spi_priv = kzalloc(sizeof(*spi_priv), GFP_KERNEL); 212 if (!spi_priv) 213 return -ENOMEM; 214 215 ret = wilc_cfg80211_init(&wilc, &spi->dev, WILC_HIF_SPI, &wilc_hif_spi); 216 if (ret) 217 goto free; 218 219 spi_set_drvdata(spi, wilc); 220 wilc->dev = &spi->dev; 221 wilc->bus_data = spi_priv; 222 wilc->dev_irq_num = spi->irq; 223 224 ret = wilc_parse_gpios(wilc); 225 if (ret < 0) 226 goto netdev_cleanup; 227 228 wilc->rtc_clk = devm_clk_get_optional(&spi->dev, "rtc"); 229 if (IS_ERR(wilc->rtc_clk)) { 230 ret = PTR_ERR(wilc->rtc_clk); 231 goto netdev_cleanup; 232 } 233 clk_prepare_enable(wilc->rtc_clk); 234 235 return 0; 236 237 netdev_cleanup: 238 wilc_netdev_cleanup(wilc); 239 free: 240 kfree(spi_priv); 241 return ret; 242 } 243 244 static void wilc_bus_remove(struct spi_device *spi) 245 { 246 struct wilc *wilc = spi_get_drvdata(spi); 247 struct wilc_spi *spi_priv = wilc->bus_data; 248 249 clk_disable_unprepare(wilc->rtc_clk); 250 wilc_netdev_cleanup(wilc); 251 kfree(spi_priv); 252 } 253 254 static const struct of_device_id wilc_of_match[] = { 255 { .compatible = "microchip,wilc1000", }, 256 { /* sentinel */ } 257 }; 258 MODULE_DEVICE_TABLE(of, wilc_of_match); 259 260 static const struct spi_device_id wilc_spi_id[] = { 261 { "wilc1000", 0 }, 262 { /* sentinel */ } 263 }; 264 MODULE_DEVICE_TABLE(spi, wilc_spi_id); 265 266 static struct spi_driver wilc_spi_driver = { 267 .driver = { 268 .name = SPI_MODALIAS, 269 .of_match_table = wilc_of_match, 270 }, 271 .id_table = wilc_spi_id, 272 .probe = wilc_bus_probe, 273 .remove = wilc_bus_remove, 274 }; 275 module_spi_driver(wilc_spi_driver); 276 MODULE_LICENSE("GPL"); 277 278 static int wilc_spi_tx(struct wilc *wilc, u8 *b, u32 len) 279 { 280 struct spi_device *spi = to_spi_device(wilc->dev); 281 int ret; 282 struct spi_message msg; 283 284 if (len > 0 && b) { 285 struct spi_transfer tr = { 286 .tx_buf = b, 287 .len = len, 288 .delay = { 289 .value = 0, 290 .unit = SPI_DELAY_UNIT_USECS 291 }, 292 }; 293 char *r_buffer = kzalloc(len, GFP_KERNEL); 294 295 if (!r_buffer) 296 return -ENOMEM; 297 298 tr.rx_buf = r_buffer; 299 dev_dbg(&spi->dev, "Request writing %d bytes\n", len); 300 301 memset(&msg, 0, sizeof(msg)); 302 spi_message_init(&msg); 303 msg.spi = spi; 304 spi_message_add_tail(&tr, &msg); 305 306 ret = spi_sync(spi, &msg); 307 if (ret < 0) 308 dev_err(&spi->dev, "SPI transaction failed\n"); 309 310 kfree(r_buffer); 311 } else { 312 dev_err(&spi->dev, 313 "can't write data with the following length: %d\n", 314 len); 315 ret = -EINVAL; 316 } 317 318 return ret; 319 } 320 321 static int wilc_spi_rx(struct wilc *wilc, u8 *rb, u32 rlen) 322 { 323 struct spi_device *spi = to_spi_device(wilc->dev); 324 int ret; 325 326 if (rlen > 0) { 327 struct spi_message msg; 328 struct spi_transfer tr = { 329 .rx_buf = rb, 330 .len = rlen, 331 .delay = { 332 .value = 0, 333 .unit = SPI_DELAY_UNIT_USECS 334 }, 335 336 }; 337 char *t_buffer = kzalloc(rlen, GFP_KERNEL); 338 339 if (!t_buffer) 340 return -ENOMEM; 341 342 tr.tx_buf = t_buffer; 343 344 memset(&msg, 0, sizeof(msg)); 345 spi_message_init(&msg); 346 msg.spi = spi; 347 spi_message_add_tail(&tr, &msg); 348 349 ret = spi_sync(spi, &msg); 350 if (ret < 0) 351 dev_err(&spi->dev, "SPI transaction failed\n"); 352 kfree(t_buffer); 353 } else { 354 dev_err(&spi->dev, 355 "can't read data with the following length: %u\n", 356 rlen); 357 ret = -EINVAL; 358 } 359 360 return ret; 361 } 362 363 static int wilc_spi_tx_rx(struct wilc *wilc, u8 *wb, u8 *rb, u32 rlen) 364 { 365 struct spi_device *spi = to_spi_device(wilc->dev); 366 int ret; 367 368 if (rlen > 0) { 369 struct spi_message msg; 370 struct spi_transfer tr = { 371 .rx_buf = rb, 372 .tx_buf = wb, 373 .len = rlen, 374 .bits_per_word = 8, 375 .delay = { 376 .value = 0, 377 .unit = SPI_DELAY_UNIT_USECS 378 }, 379 380 }; 381 382 memset(&msg, 0, sizeof(msg)); 383 spi_message_init(&msg); 384 msg.spi = spi; 385 386 spi_message_add_tail(&tr, &msg); 387 ret = spi_sync(spi, &msg); 388 if (ret < 0) 389 dev_err(&spi->dev, "SPI transaction failed\n"); 390 } else { 391 dev_err(&spi->dev, 392 "can't read data with the following length: %u\n", 393 rlen); 394 ret = -EINVAL; 395 } 396 397 return ret; 398 } 399 400 static int spi_data_write(struct wilc *wilc, u8 *b, u32 sz) 401 { 402 struct spi_device *spi = to_spi_device(wilc->dev); 403 struct wilc_spi *spi_priv = wilc->bus_data; 404 int ix, nbytes; 405 int result = 0; 406 u8 cmd, order, crc[2]; 407 u16 crc_calc; 408 409 /* 410 * Data 411 */ 412 ix = 0; 413 do { 414 if (sz <= DATA_PKT_SZ) { 415 nbytes = sz; 416 order = 0x3; 417 } else { 418 nbytes = DATA_PKT_SZ; 419 if (ix == 0) 420 order = 0x1; 421 else 422 order = 0x02; 423 } 424 425 /* 426 * Write command 427 */ 428 cmd = 0xf0; 429 cmd |= order; 430 431 if (wilc_spi_tx(wilc, &cmd, 1)) { 432 dev_err(&spi->dev, 433 "Failed data block cmd write, bus error...\n"); 434 result = -EINVAL; 435 break; 436 } 437 438 /* 439 * Write data 440 */ 441 if (wilc_spi_tx(wilc, &b[ix], nbytes)) { 442 dev_err(&spi->dev, 443 "Failed data block write, bus error...\n"); 444 result = -EINVAL; 445 break; 446 } 447 448 /* 449 * Write CRC 450 */ 451 if (spi_priv->crc16_enabled) { 452 crc_calc = crc_itu_t(0xffff, &b[ix], nbytes); 453 crc[0] = crc_calc >> 8; 454 crc[1] = crc_calc; 455 if (wilc_spi_tx(wilc, crc, 2)) { 456 dev_err(&spi->dev, "Failed data block crc write, bus error...\n"); 457 result = -EINVAL; 458 break; 459 } 460 } 461 462 /* 463 * No need to wait for response 464 */ 465 ix += nbytes; 466 sz -= nbytes; 467 } while (sz); 468 469 return result; 470 } 471 472 /******************************************** 473 * 474 * Spi Internal Read/Write Function 475 * 476 ********************************************/ 477 static u8 wilc_get_crc7(u8 *buffer, u32 len) 478 { 479 return crc7_be(0xfe, buffer, len); 480 } 481 482 static int wilc_spi_single_read(struct wilc *wilc, u8 cmd, u32 adr, void *b, 483 u8 clockless) 484 { 485 struct spi_device *spi = to_spi_device(wilc->dev); 486 struct wilc_spi *spi_priv = wilc->bus_data; 487 u8 wb[32], rb[32]; 488 int cmd_len, resp_len, i; 489 u16 crc_calc, crc_recv; 490 struct wilc_spi_cmd *c; 491 struct wilc_spi_rsp_data *r; 492 struct wilc_spi_read_rsp_data *r_data; 493 494 memset(wb, 0x0, sizeof(wb)); 495 memset(rb, 0x0, sizeof(rb)); 496 c = (struct wilc_spi_cmd *)wb; 497 c->cmd_type = cmd; 498 if (cmd == CMD_SINGLE_READ) { 499 c->u.simple_cmd.addr[0] = adr >> 16; 500 c->u.simple_cmd.addr[1] = adr >> 8; 501 c->u.simple_cmd.addr[2] = adr; 502 } else if (cmd == CMD_INTERNAL_READ) { 503 c->u.simple_cmd.addr[0] = adr >> 8; 504 if (clockless == 1) 505 c->u.simple_cmd.addr[0] |= BIT(7); 506 c->u.simple_cmd.addr[1] = adr; 507 c->u.simple_cmd.addr[2] = 0x0; 508 } else { 509 dev_err(&spi->dev, "cmd [%x] not supported\n", cmd); 510 return -EINVAL; 511 } 512 513 cmd_len = offsetof(struct wilc_spi_cmd, u.simple_cmd.crc); 514 resp_len = sizeof(*r) + sizeof(*r_data) + WILC_SPI_RSP_HDR_EXTRA_DATA; 515 516 if (spi_priv->crc7_enabled) { 517 c->u.simple_cmd.crc[0] = wilc_get_crc7(wb, cmd_len); 518 cmd_len += 1; 519 resp_len += 2; 520 } 521 522 if (cmd_len + resp_len > ARRAY_SIZE(wb)) { 523 dev_err(&spi->dev, 524 "spi buffer size too small (%d) (%d) (%zu)\n", 525 cmd_len, resp_len, ARRAY_SIZE(wb)); 526 return -EINVAL; 527 } 528 529 if (wilc_spi_tx_rx(wilc, wb, rb, cmd_len + resp_len)) { 530 dev_err(&spi->dev, "Failed cmd write, bus error...\n"); 531 return -EINVAL; 532 } 533 534 r = (struct wilc_spi_rsp_data *)&rb[cmd_len]; 535 if (r->rsp_cmd_type != cmd && !clockless) { 536 if (!spi_priv->probing_crc) 537 dev_err(&spi->dev, 538 "Failed cmd, cmd (%02x), resp (%02x)\n", 539 cmd, r->rsp_cmd_type); 540 return -EINVAL; 541 } 542 543 if (r->status != WILC_SPI_COMMAND_STAT_SUCCESS && !clockless) { 544 dev_err(&spi->dev, "Failed cmd state response state (%02x)\n", 545 r->status); 546 return -EINVAL; 547 } 548 549 for (i = 0; i < WILC_SPI_RSP_HDR_EXTRA_DATA; ++i) 550 if (WILC_GET_RESP_HDR_START(r->data[i]) == 0xf) 551 break; 552 553 if (i >= WILC_SPI_RSP_HDR_EXTRA_DATA) { 554 dev_err(&spi->dev, "Error, data start missing\n"); 555 return -EINVAL; 556 } 557 558 r_data = (struct wilc_spi_read_rsp_data *)&r->data[i]; 559 560 if (b) 561 memcpy(b, r_data->data, 4); 562 563 if (!clockless && spi_priv->crc16_enabled) { 564 crc_recv = (r_data->crc[0] << 8) | r_data->crc[1]; 565 crc_calc = crc_itu_t(0xffff, r_data->data, 4); 566 if (crc_recv != crc_calc) { 567 dev_err(&spi->dev, "%s: bad CRC 0x%04x " 568 "(calculated 0x%04x)\n", __func__, 569 crc_recv, crc_calc); 570 return -EINVAL; 571 } 572 } 573 574 return 0; 575 } 576 577 static int wilc_spi_write_cmd(struct wilc *wilc, u8 cmd, u32 adr, u32 data, 578 u8 clockless) 579 { 580 struct spi_device *spi = to_spi_device(wilc->dev); 581 struct wilc_spi *spi_priv = wilc->bus_data; 582 u8 wb[32], rb[32]; 583 int cmd_len, resp_len; 584 struct wilc_spi_cmd *c; 585 struct wilc_spi_rsp_data *r; 586 587 memset(wb, 0x0, sizeof(wb)); 588 memset(rb, 0x0, sizeof(rb)); 589 c = (struct wilc_spi_cmd *)wb; 590 c->cmd_type = cmd; 591 if (cmd == CMD_INTERNAL_WRITE) { 592 c->u.internal_w_cmd.addr[0] = adr >> 8; 593 if (clockless == 1) 594 c->u.internal_w_cmd.addr[0] |= BIT(7); 595 596 c->u.internal_w_cmd.addr[1] = adr; 597 c->u.internal_w_cmd.data = cpu_to_be32(data); 598 cmd_len = offsetof(struct wilc_spi_cmd, u.internal_w_cmd.crc); 599 if (spi_priv->crc7_enabled) 600 c->u.internal_w_cmd.crc[0] = wilc_get_crc7(wb, cmd_len); 601 } else if (cmd == CMD_SINGLE_WRITE) { 602 c->u.w_cmd.addr[0] = adr >> 16; 603 c->u.w_cmd.addr[1] = adr >> 8; 604 c->u.w_cmd.addr[2] = adr; 605 c->u.w_cmd.data = cpu_to_be32(data); 606 cmd_len = offsetof(struct wilc_spi_cmd, u.w_cmd.crc); 607 if (spi_priv->crc7_enabled) 608 c->u.w_cmd.crc[0] = wilc_get_crc7(wb, cmd_len); 609 } else { 610 dev_err(&spi->dev, "write cmd [%x] not supported\n", cmd); 611 return -EINVAL; 612 } 613 614 if (spi_priv->crc7_enabled) 615 cmd_len += 1; 616 617 resp_len = sizeof(*r); 618 619 if (cmd_len + resp_len > ARRAY_SIZE(wb)) { 620 dev_err(&spi->dev, 621 "spi buffer size too small (%d) (%d) (%zu)\n", 622 cmd_len, resp_len, ARRAY_SIZE(wb)); 623 return -EINVAL; 624 } 625 626 if (wilc_spi_tx_rx(wilc, wb, rb, cmd_len + resp_len)) { 627 dev_err(&spi->dev, "Failed cmd write, bus error...\n"); 628 return -EINVAL; 629 } 630 631 r = (struct wilc_spi_rsp_data *)&rb[cmd_len]; 632 /* 633 * Clockless registers operations might return unexptected responses, 634 * even if successful. 635 */ 636 if (r->rsp_cmd_type != cmd && !clockless) { 637 dev_err(&spi->dev, 638 "Failed cmd response, cmd (%02x), resp (%02x)\n", 639 cmd, r->rsp_cmd_type); 640 return -EINVAL; 641 } 642 643 if (r->status != WILC_SPI_COMMAND_STAT_SUCCESS && !clockless) { 644 dev_err(&spi->dev, "Failed cmd state response state (%02x)\n", 645 r->status); 646 return -EINVAL; 647 } 648 649 return 0; 650 } 651 652 static int wilc_spi_dma_rw(struct wilc *wilc, u8 cmd, u32 adr, u8 *b, u32 sz) 653 { 654 struct spi_device *spi = to_spi_device(wilc->dev); 655 struct wilc_spi *spi_priv = wilc->bus_data; 656 u16 crc_recv, crc_calc; 657 u8 wb[32], rb[32]; 658 int cmd_len, resp_len; 659 int retry, ix = 0; 660 u8 crc[2]; 661 struct wilc_spi_cmd *c; 662 struct wilc_spi_rsp_data *r; 663 664 memset(wb, 0x0, sizeof(wb)); 665 memset(rb, 0x0, sizeof(rb)); 666 c = (struct wilc_spi_cmd *)wb; 667 c->cmd_type = cmd; 668 if (cmd == CMD_DMA_WRITE || cmd == CMD_DMA_READ) { 669 c->u.dma_cmd.addr[0] = adr >> 16; 670 c->u.dma_cmd.addr[1] = adr >> 8; 671 c->u.dma_cmd.addr[2] = adr; 672 c->u.dma_cmd.size[0] = sz >> 8; 673 c->u.dma_cmd.size[1] = sz; 674 cmd_len = offsetof(struct wilc_spi_cmd, u.dma_cmd.crc); 675 if (spi_priv->crc7_enabled) 676 c->u.dma_cmd.crc[0] = wilc_get_crc7(wb, cmd_len); 677 } else if (cmd == CMD_DMA_EXT_WRITE || cmd == CMD_DMA_EXT_READ) { 678 c->u.dma_cmd_ext.addr[0] = adr >> 16; 679 c->u.dma_cmd_ext.addr[1] = adr >> 8; 680 c->u.dma_cmd_ext.addr[2] = adr; 681 c->u.dma_cmd_ext.size[0] = sz >> 16; 682 c->u.dma_cmd_ext.size[1] = sz >> 8; 683 c->u.dma_cmd_ext.size[2] = sz; 684 cmd_len = offsetof(struct wilc_spi_cmd, u.dma_cmd_ext.crc); 685 if (spi_priv->crc7_enabled) 686 c->u.dma_cmd_ext.crc[0] = wilc_get_crc7(wb, cmd_len); 687 } else { 688 dev_err(&spi->dev, "dma read write cmd [%x] not supported\n", 689 cmd); 690 return -EINVAL; 691 } 692 if (spi_priv->crc7_enabled) 693 cmd_len += 1; 694 695 resp_len = sizeof(*r); 696 697 if (cmd_len + resp_len > ARRAY_SIZE(wb)) { 698 dev_err(&spi->dev, "spi buffer size too small (%d)(%d) (%zu)\n", 699 cmd_len, resp_len, ARRAY_SIZE(wb)); 700 return -EINVAL; 701 } 702 703 if (wilc_spi_tx_rx(wilc, wb, rb, cmd_len + resp_len)) { 704 dev_err(&spi->dev, "Failed cmd write, bus error...\n"); 705 return -EINVAL; 706 } 707 708 r = (struct wilc_spi_rsp_data *)&rb[cmd_len]; 709 if (r->rsp_cmd_type != cmd) { 710 dev_err(&spi->dev, 711 "Failed cmd response, cmd (%02x), resp (%02x)\n", 712 cmd, r->rsp_cmd_type); 713 return -EINVAL; 714 } 715 716 if (r->status != WILC_SPI_COMMAND_STAT_SUCCESS) { 717 dev_err(&spi->dev, "Failed cmd state response state (%02x)\n", 718 r->status); 719 return -EINVAL; 720 } 721 722 if (cmd == CMD_DMA_WRITE || cmd == CMD_DMA_EXT_WRITE) 723 return 0; 724 725 while (sz > 0) { 726 int nbytes; 727 u8 rsp; 728 729 nbytes = min_t(u32, sz, DATA_PKT_SZ); 730 731 /* 732 * Data Response header 733 */ 734 retry = 100; 735 do { 736 if (wilc_spi_rx(wilc, &rsp, 1)) { 737 dev_err(&spi->dev, 738 "Failed resp read, bus err\n"); 739 return -EINVAL; 740 } 741 if (WILC_GET_RESP_HDR_START(rsp) == 0xf) 742 break; 743 } while (retry--); 744 745 /* 746 * Read bytes 747 */ 748 if (wilc_spi_rx(wilc, &b[ix], nbytes)) { 749 dev_err(&spi->dev, 750 "Failed block read, bus err\n"); 751 return -EINVAL; 752 } 753 754 /* 755 * Read CRC 756 */ 757 if (spi_priv->crc16_enabled) { 758 if (wilc_spi_rx(wilc, crc, 2)) { 759 dev_err(&spi->dev, 760 "Failed block CRC read, bus err\n"); 761 return -EINVAL; 762 } 763 crc_recv = (crc[0] << 8) | crc[1]; 764 crc_calc = crc_itu_t(0xffff, &b[ix], nbytes); 765 if (crc_recv != crc_calc) { 766 dev_err(&spi->dev, "%s: bad CRC 0x%04x " 767 "(calculated 0x%04x)\n", __func__, 768 crc_recv, crc_calc); 769 return -EINVAL; 770 } 771 } 772 773 ix += nbytes; 774 sz -= nbytes; 775 } 776 return 0; 777 } 778 779 static int wilc_spi_special_cmd(struct wilc *wilc, u8 cmd) 780 { 781 struct spi_device *spi = to_spi_device(wilc->dev); 782 struct wilc_spi *spi_priv = wilc->bus_data; 783 u8 wb[32], rb[32]; 784 int cmd_len, resp_len = 0; 785 struct wilc_spi_cmd *c; 786 struct wilc_spi_special_cmd_rsp *r; 787 788 if (cmd != CMD_TERMINATE && cmd != CMD_REPEAT && cmd != CMD_RESET) 789 return -EINVAL; 790 791 memset(wb, 0x0, sizeof(wb)); 792 memset(rb, 0x0, sizeof(rb)); 793 c = (struct wilc_spi_cmd *)wb; 794 c->cmd_type = cmd; 795 796 if (cmd == CMD_RESET) 797 memset(c->u.simple_cmd.addr, 0xFF, 3); 798 799 cmd_len = offsetof(struct wilc_spi_cmd, u.simple_cmd.crc); 800 resp_len = sizeof(*r); 801 802 if (spi_priv->crc7_enabled) { 803 c->u.simple_cmd.crc[0] = wilc_get_crc7(wb, cmd_len); 804 cmd_len += 1; 805 } 806 if (cmd_len + resp_len > ARRAY_SIZE(wb)) { 807 dev_err(&spi->dev, "spi buffer size too small (%d) (%d) (%zu)\n", 808 cmd_len, resp_len, ARRAY_SIZE(wb)); 809 return -EINVAL; 810 } 811 812 if (wilc_spi_tx_rx(wilc, wb, rb, cmd_len + resp_len)) { 813 dev_err(&spi->dev, "Failed cmd write, bus error...\n"); 814 return -EINVAL; 815 } 816 817 r = (struct wilc_spi_special_cmd_rsp *)&rb[cmd_len]; 818 if (r->rsp_cmd_type != cmd) { 819 if (!spi_priv->probing_crc) 820 dev_err(&spi->dev, 821 "Failed cmd response, cmd (%02x), resp (%02x)\n", 822 cmd, r->rsp_cmd_type); 823 return -EINVAL; 824 } 825 826 if (r->status != WILC_SPI_COMMAND_STAT_SUCCESS) { 827 dev_err(&spi->dev, "Failed cmd state response state (%02x)\n", 828 r->status); 829 return -EINVAL; 830 } 831 return 0; 832 } 833 834 static void wilc_spi_reset_cmd_sequence(struct wilc *wl, u8 attempt, u32 addr) 835 { 836 struct spi_device *spi = to_spi_device(wl->dev); 837 struct wilc_spi *spi_priv = wl->bus_data; 838 839 if (!spi_priv->probing_crc) 840 dev_err(&spi->dev, "Reset and retry %d %x\n", attempt, addr); 841 842 usleep_range(1000, 1100); 843 wilc_spi_reset(wl); 844 usleep_range(1000, 1100); 845 } 846 847 static int wilc_spi_read_reg(struct wilc *wilc, u32 addr, u32 *data) 848 { 849 struct spi_device *spi = to_spi_device(wilc->dev); 850 int result; 851 u8 cmd = CMD_SINGLE_READ; 852 u8 clockless = 0; 853 u8 i; 854 855 if (addr <= WILC_SPI_CLOCKLESS_ADDR_LIMIT) { 856 /* Clockless register */ 857 cmd = CMD_INTERNAL_READ; 858 clockless = 1; 859 } 860 861 for (i = 0; i < SPI_RETRY_MAX_LIMIT; i++) { 862 result = wilc_spi_single_read(wilc, cmd, addr, data, clockless); 863 if (!result) { 864 le32_to_cpus(data); 865 return 0; 866 } 867 868 /* retry is not applicable for clockless registers */ 869 if (clockless) 870 break; 871 872 dev_err(&spi->dev, "Failed cmd, read reg (%08x)...\n", addr); 873 wilc_spi_reset_cmd_sequence(wilc, i, addr); 874 } 875 876 return result; 877 } 878 879 static int wilc_spi_read(struct wilc *wilc, u32 addr, u8 *buf, u32 size) 880 { 881 struct spi_device *spi = to_spi_device(wilc->dev); 882 int result; 883 u8 i; 884 885 if (size <= 4) 886 return -EINVAL; 887 888 for (i = 0; i < SPI_RETRY_MAX_LIMIT; i++) { 889 result = wilc_spi_dma_rw(wilc, CMD_DMA_EXT_READ, addr, 890 buf, size); 891 if (!result) 892 return 0; 893 894 dev_err(&spi->dev, "Failed cmd, read block (%08x)...\n", addr); 895 896 wilc_spi_reset_cmd_sequence(wilc, i, addr); 897 } 898 899 return result; 900 } 901 902 static int spi_internal_write(struct wilc *wilc, u32 adr, u32 dat) 903 { 904 struct spi_device *spi = to_spi_device(wilc->dev); 905 int result; 906 u8 i; 907 908 for (i = 0; i < SPI_RETRY_MAX_LIMIT; i++) { 909 result = wilc_spi_write_cmd(wilc, CMD_INTERNAL_WRITE, adr, 910 dat, 0); 911 if (!result) 912 return 0; 913 dev_err(&spi->dev, "Failed internal write cmd...\n"); 914 915 wilc_spi_reset_cmd_sequence(wilc, i, adr); 916 } 917 918 return result; 919 } 920 921 static int spi_internal_read(struct wilc *wilc, u32 adr, u32 *data) 922 { 923 struct spi_device *spi = to_spi_device(wilc->dev); 924 struct wilc_spi *spi_priv = wilc->bus_data; 925 int result; 926 u8 i; 927 928 for (i = 0; i < SPI_RETRY_MAX_LIMIT; i++) { 929 result = wilc_spi_single_read(wilc, CMD_INTERNAL_READ, adr, 930 data, 0); 931 if (!result) { 932 le32_to_cpus(data); 933 return 0; 934 } 935 if (!spi_priv->probing_crc) 936 dev_err(&spi->dev, "Failed internal read cmd...\n"); 937 938 wilc_spi_reset_cmd_sequence(wilc, i, adr); 939 } 940 941 return result; 942 } 943 944 /******************************************** 945 * 946 * Spi interfaces 947 * 948 ********************************************/ 949 950 static int wilc_spi_write_reg(struct wilc *wilc, u32 addr, u32 data) 951 { 952 struct spi_device *spi = to_spi_device(wilc->dev); 953 int result; 954 u8 cmd = CMD_SINGLE_WRITE; 955 u8 clockless = 0; 956 u8 i; 957 958 if (addr <= WILC_SPI_CLOCKLESS_ADDR_LIMIT) { 959 /* Clockless register */ 960 cmd = CMD_INTERNAL_WRITE; 961 clockless = 1; 962 } 963 964 for (i = 0; i < SPI_RETRY_MAX_LIMIT; i++) { 965 result = wilc_spi_write_cmd(wilc, cmd, addr, data, clockless); 966 if (!result) 967 return 0; 968 969 dev_err(&spi->dev, "Failed cmd, write reg (%08x)...\n", addr); 970 971 if (clockless) 972 break; 973 974 wilc_spi_reset_cmd_sequence(wilc, i, addr); 975 } 976 return result; 977 } 978 979 static int spi_data_rsp(struct wilc *wilc, u8 cmd) 980 { 981 struct spi_device *spi = to_spi_device(wilc->dev); 982 int result, i; 983 u8 rsp[4]; 984 985 /* 986 * The response to data packets is two bytes long. For 987 * efficiency's sake, wilc_spi_write() wisely ignores the 988 * responses for all packets but the final one. The downside 989 * of that optimization is that when the final data packet is 990 * short, we may receive (part of) the response to the 991 * second-to-last packet before the one for the final packet. 992 * To handle this, we always read 4 bytes and then search for 993 * the last byte that contains the "Response Start" code (0xc 994 * in the top 4 bits). We then know that this byte is the 995 * first response byte of the final data packet. 996 */ 997 result = wilc_spi_rx(wilc, rsp, sizeof(rsp)); 998 if (result) { 999 dev_err(&spi->dev, "Failed bus error...\n"); 1000 return result; 1001 } 1002 1003 for (i = sizeof(rsp) - 2; i >= 0; --i) 1004 if (FIELD_GET(RSP_START_FIELD, rsp[i]) == RSP_START_TAG) 1005 break; 1006 1007 if (i < 0) { 1008 dev_err(&spi->dev, 1009 "Data packet response missing (%02x %02x %02x %02x)\n", 1010 rsp[0], rsp[1], rsp[2], rsp[3]); 1011 return -1; 1012 } 1013 1014 /* rsp[i] is the last response start byte */ 1015 1016 if (FIELD_GET(RSP_TYPE_FIELD, rsp[i]) != RSP_TYPE_LAST_PACKET 1017 || rsp[i + 1] != RSP_STATE_NO_ERROR) { 1018 dev_err(&spi->dev, "Data response error (%02x %02x)\n", 1019 rsp[i], rsp[i + 1]); 1020 return -1; 1021 } 1022 return 0; 1023 } 1024 1025 static int wilc_spi_write(struct wilc *wilc, u32 addr, u8 *buf, u32 size) 1026 { 1027 struct spi_device *spi = to_spi_device(wilc->dev); 1028 int result; 1029 u8 i; 1030 1031 /* 1032 * has to be greated than 4 1033 */ 1034 if (size <= 4) 1035 return -EINVAL; 1036 1037 for (i = 0; i < SPI_RETRY_MAX_LIMIT; i++) { 1038 result = wilc_spi_dma_rw(wilc, CMD_DMA_EXT_WRITE, addr, 1039 NULL, size); 1040 if (result) { 1041 dev_err(&spi->dev, 1042 "Failed cmd, write block (%08x)...\n", addr); 1043 wilc_spi_reset_cmd_sequence(wilc, i, addr); 1044 continue; 1045 } 1046 1047 /* 1048 * Data 1049 */ 1050 result = spi_data_write(wilc, buf, size); 1051 if (result) { 1052 dev_err(&spi->dev, "Failed block data write...\n"); 1053 wilc_spi_reset_cmd_sequence(wilc, i, addr); 1054 continue; 1055 } 1056 1057 /* 1058 * Data response 1059 */ 1060 result = spi_data_rsp(wilc, CMD_DMA_EXT_WRITE); 1061 if (result) { 1062 dev_err(&spi->dev, "Failed block data rsp...\n"); 1063 wilc_spi_reset_cmd_sequence(wilc, i, addr); 1064 continue; 1065 } 1066 break; 1067 } 1068 return result; 1069 } 1070 1071 /******************************************** 1072 * 1073 * Bus interfaces 1074 * 1075 ********************************************/ 1076 1077 static int wilc_spi_reset(struct wilc *wilc) 1078 { 1079 struct spi_device *spi = to_spi_device(wilc->dev); 1080 struct wilc_spi *spi_priv = wilc->bus_data; 1081 int result; 1082 1083 result = wilc_spi_special_cmd(wilc, CMD_RESET); 1084 if (result && !spi_priv->probing_crc) 1085 dev_err(&spi->dev, "Failed cmd reset\n"); 1086 1087 return result; 1088 } 1089 1090 static bool wilc_spi_is_init(struct wilc *wilc) 1091 { 1092 struct wilc_spi *spi_priv = wilc->bus_data; 1093 1094 return spi_priv->isinit; 1095 } 1096 1097 static int wilc_spi_deinit(struct wilc *wilc) 1098 { 1099 struct wilc_spi *spi_priv = wilc->bus_data; 1100 1101 spi_priv->isinit = false; 1102 wilc_wlan_power(wilc, false); 1103 return 0; 1104 } 1105 1106 static int wilc_spi_init(struct wilc *wilc, bool resume) 1107 { 1108 struct spi_device *spi = to_spi_device(wilc->dev); 1109 struct wilc_spi *spi_priv = wilc->bus_data; 1110 u32 reg; 1111 u32 chipid; 1112 int ret, i; 1113 1114 if (spi_priv->isinit) { 1115 /* Confirm we can read chipid register without error: */ 1116 ret = wilc_spi_read_reg(wilc, WILC_CHIPID, &chipid); 1117 if (ret == 0) 1118 return 0; 1119 1120 dev_err(&spi->dev, "Fail cmd read chip id...\n"); 1121 } 1122 1123 wilc_wlan_power(wilc, true); 1124 1125 /* 1126 * configure protocol 1127 */ 1128 1129 /* 1130 * Infer the CRC settings that are currently in effect. This 1131 * is necessary because we can't be sure that the chip has 1132 * been RESET (e.g, after module unload and reload). 1133 */ 1134 spi_priv->probing_crc = true; 1135 spi_priv->crc7_enabled = enable_crc7; 1136 spi_priv->crc16_enabled = false; /* don't check CRC16 during probing */ 1137 for (i = 0; i < 2; ++i) { 1138 ret = spi_internal_read(wilc, WILC_SPI_PROTOCOL_OFFSET, ®); 1139 if (ret == 0) 1140 break; 1141 spi_priv->crc7_enabled = !enable_crc7; 1142 } 1143 if (ret) { 1144 dev_err(&spi->dev, "Failed with CRC7 on and off.\n"); 1145 return ret; 1146 } 1147 1148 /* set up the desired CRC configuration: */ 1149 reg &= ~(PROTOCOL_REG_CRC7_MASK | PROTOCOL_REG_CRC16_MASK); 1150 if (enable_crc7) 1151 reg |= PROTOCOL_REG_CRC7_MASK; 1152 if (enable_crc16) 1153 reg |= PROTOCOL_REG_CRC16_MASK; 1154 1155 /* set up the data packet size: */ 1156 BUILD_BUG_ON(DATA_PKT_LOG_SZ < DATA_PKT_LOG_SZ_MIN 1157 || DATA_PKT_LOG_SZ > DATA_PKT_LOG_SZ_MAX); 1158 reg &= ~PROTOCOL_REG_PKT_SZ_MASK; 1159 reg |= FIELD_PREP(PROTOCOL_REG_PKT_SZ_MASK, 1160 DATA_PKT_LOG_SZ - DATA_PKT_LOG_SZ_MIN); 1161 1162 /* establish the new setup: */ 1163 ret = spi_internal_write(wilc, WILC_SPI_PROTOCOL_OFFSET, reg); 1164 if (ret) { 1165 dev_err(&spi->dev, 1166 "[wilc spi %d]: Failed internal write reg\n", 1167 __LINE__); 1168 return ret; 1169 } 1170 /* update our state to match new protocol settings: */ 1171 spi_priv->crc7_enabled = enable_crc7; 1172 spi_priv->crc16_enabled = enable_crc16; 1173 1174 /* re-read to make sure new settings are in effect: */ 1175 spi_internal_read(wilc, WILC_SPI_PROTOCOL_OFFSET, ®); 1176 1177 spi_priv->probing_crc = false; 1178 1179 /* 1180 * make sure can read chip id without protocol error 1181 */ 1182 ret = wilc_spi_read_reg(wilc, WILC_CHIPID, &chipid); 1183 if (ret) { 1184 dev_err(&spi->dev, "Fail cmd read chip id...\n"); 1185 return ret; 1186 } 1187 1188 spi_priv->isinit = true; 1189 1190 return 0; 1191 } 1192 1193 static int wilc_spi_read_size(struct wilc *wilc, u32 *size) 1194 { 1195 int ret; 1196 1197 ret = spi_internal_read(wilc, 1198 WILC_SPI_INT_STATUS - WILC_SPI_REG_BASE, size); 1199 *size = FIELD_GET(IRQ_DMA_WD_CNT_MASK, *size); 1200 1201 return ret; 1202 } 1203 1204 static int wilc_spi_read_int(struct wilc *wilc, u32 *int_status) 1205 { 1206 return spi_internal_read(wilc, WILC_SPI_INT_STATUS - WILC_SPI_REG_BASE, 1207 int_status); 1208 } 1209 1210 static int wilc_spi_clear_int_ext(struct wilc *wilc, u32 val) 1211 { 1212 int ret; 1213 int retry = SPI_ENABLE_VMM_RETRY_LIMIT; 1214 u32 check; 1215 1216 while (retry) { 1217 ret = spi_internal_write(wilc, 1218 WILC_SPI_INT_CLEAR - WILC_SPI_REG_BASE, 1219 val); 1220 if (ret) 1221 break; 1222 1223 ret = spi_internal_read(wilc, 1224 WILC_SPI_INT_CLEAR - WILC_SPI_REG_BASE, 1225 &check); 1226 if (ret || ((check & EN_VMM) == (val & EN_VMM))) 1227 break; 1228 1229 retry--; 1230 } 1231 return ret; 1232 } 1233 1234 static int wilc_spi_sync_ext(struct wilc *wilc, int nint) 1235 { 1236 struct spi_device *spi = to_spi_device(wilc->dev); 1237 u32 reg; 1238 int ret, i; 1239 1240 if (nint > MAX_NUM_INT) { 1241 dev_err(&spi->dev, "Too many interrupts (%d)...\n", nint); 1242 return -EINVAL; 1243 } 1244 1245 /* 1246 * interrupt pin mux select 1247 */ 1248 ret = wilc_spi_read_reg(wilc, WILC_PIN_MUX_0, ®); 1249 if (ret) { 1250 dev_err(&spi->dev, "Failed read reg (%08x)...\n", 1251 WILC_PIN_MUX_0); 1252 return ret; 1253 } 1254 reg |= BIT(8); 1255 ret = wilc_spi_write_reg(wilc, WILC_PIN_MUX_0, reg); 1256 if (ret) { 1257 dev_err(&spi->dev, "Failed write reg (%08x)...\n", 1258 WILC_PIN_MUX_0); 1259 return ret; 1260 } 1261 1262 /* 1263 * interrupt enable 1264 */ 1265 ret = wilc_spi_read_reg(wilc, WILC_INTR_ENABLE, ®); 1266 if (ret) { 1267 dev_err(&spi->dev, "Failed read reg (%08x)...\n", 1268 WILC_INTR_ENABLE); 1269 return ret; 1270 } 1271 1272 for (i = 0; (i < 5) && (nint > 0); i++, nint--) 1273 reg |= (BIT((27 + i))); 1274 1275 ret = wilc_spi_write_reg(wilc, WILC_INTR_ENABLE, reg); 1276 if (ret) { 1277 dev_err(&spi->dev, "Failed write reg (%08x)...\n", 1278 WILC_INTR_ENABLE); 1279 return ret; 1280 } 1281 if (nint) { 1282 ret = wilc_spi_read_reg(wilc, WILC_INTR2_ENABLE, ®); 1283 if (ret) { 1284 dev_err(&spi->dev, "Failed read reg (%08x)...\n", 1285 WILC_INTR2_ENABLE); 1286 return ret; 1287 } 1288 1289 for (i = 0; (i < 3) && (nint > 0); i++, nint--) 1290 reg |= BIT(i); 1291 1292 ret = wilc_spi_write_reg(wilc, WILC_INTR2_ENABLE, reg); 1293 if (ret) { 1294 dev_err(&spi->dev, "Failed write reg (%08x)...\n", 1295 WILC_INTR2_ENABLE); 1296 return ret; 1297 } 1298 } 1299 1300 return 0; 1301 } 1302 1303 /* Global spi HIF function table */ 1304 static const struct wilc_hif_func wilc_hif_spi = { 1305 .hif_init = wilc_spi_init, 1306 .hif_deinit = wilc_spi_deinit, 1307 .hif_read_reg = wilc_spi_read_reg, 1308 .hif_write_reg = wilc_spi_write_reg, 1309 .hif_block_rx = wilc_spi_read, 1310 .hif_block_tx = wilc_spi_write, 1311 .hif_read_int = wilc_spi_read_int, 1312 .hif_clear_int_ext = wilc_spi_clear_int_ext, 1313 .hif_read_size = wilc_spi_read_size, 1314 .hif_block_tx_ext = wilc_spi_write, 1315 .hif_block_rx_ext = wilc_spi_read, 1316 .hif_sync_ext = wilc_spi_sync_ext, 1317 .hif_reset = wilc_spi_reset, 1318 .hif_is_init = wilc_spi_is_init, 1319 }; 1320