1 // SPDX-License-Identifier: ISC 2 /* 3 * Copyright (c) 2012 Broadcom Corporation 4 */ 5 6 7 #ifndef FWIL_TYPES_H_ 8 #define FWIL_TYPES_H_ 9 10 #include <linux/if_ether.h> 11 12 13 #define BRCMF_FIL_ACTION_FRAME_SIZE 1800 14 15 /* ARP Offload feature flags for arp_ol iovar */ 16 #define BRCMF_ARP_OL_AGENT 0x00000001 17 #define BRCMF_ARP_OL_SNOOP 0x00000002 18 #define BRCMF_ARP_OL_HOST_AUTO_REPLY 0x00000004 19 #define BRCMF_ARP_OL_PEER_AUTO_REPLY 0x00000008 20 21 #define BRCMF_BSS_INFO_VERSION 109 /* curr ver of brcmf_bss_info_le struct */ 22 #define BRCMF_BSS_RSSI_ON_CHANNEL 0x0004 23 24 #define BRCMF_STA_BRCM 0x00000001 /* Running a Broadcom driver */ 25 #define BRCMF_STA_WME 0x00000002 /* WMM association */ 26 #define BRCMF_STA_NONERP 0x00000004 /* No ERP */ 27 #define BRCMF_STA_AUTHE 0x00000008 /* Authenticated */ 28 #define BRCMF_STA_ASSOC 0x00000010 /* Associated */ 29 #define BRCMF_STA_AUTHO 0x00000020 /* Authorized */ 30 #define BRCMF_STA_WDS 0x00000040 /* Wireless Distribution System */ 31 #define BRCMF_STA_WDS_LINKUP 0x00000080 /* WDS traffic/probes flowing properly */ 32 #define BRCMF_STA_PS 0x00000100 /* STA is in power save mode from AP's viewpoint */ 33 #define BRCMF_STA_APSD_BE 0x00000200 /* APSD delv/trigger for AC_BE is default enabled */ 34 #define BRCMF_STA_APSD_BK 0x00000400 /* APSD delv/trigger for AC_BK is default enabled */ 35 #define BRCMF_STA_APSD_VI 0x00000800 /* APSD delv/trigger for AC_VI is default enabled */ 36 #define BRCMF_STA_APSD_VO 0x00001000 /* APSD delv/trigger for AC_VO is default enabled */ 37 #define BRCMF_STA_N_CAP 0x00002000 /* STA 802.11n capable */ 38 #define BRCMF_STA_SCBSTATS 0x00004000 /* Per STA debug stats */ 39 #define BRCMF_STA_AMPDU_CAP 0x00008000 /* STA AMPDU capable */ 40 #define BRCMF_STA_AMSDU_CAP 0x00010000 /* STA AMSDU capable */ 41 #define BRCMF_STA_MIMO_PS 0x00020000 /* mimo ps mode is enabled */ 42 #define BRCMF_STA_MIMO_RTS 0x00040000 /* send rts in mimo ps mode */ 43 #define BRCMF_STA_RIFS_CAP 0x00080000 /* rifs enabled */ 44 #define BRCMF_STA_VHT_CAP 0x00100000 /* STA VHT(11ac) capable */ 45 #define BRCMF_STA_WPS 0x00200000 /* WPS state */ 46 #define BRCMF_STA_DWDS_CAP 0x01000000 /* DWDS CAP */ 47 #define BRCMF_STA_DWDS 0x02000000 /* DWDS active */ 48 49 /* size of brcmf_scan_params not including variable length array */ 50 #define BRCMF_SCAN_PARAMS_FIXED_SIZE 64 51 #define BRCMF_SCAN_PARAMS_V2_FIXED_SIZE 72 52 53 /* version of brcmf_scan_params structure */ 54 #define BRCMF_SCAN_PARAMS_VERSION_V2 2 55 56 /* masks for channel and ssid count */ 57 #define BRCMF_SCAN_PARAMS_COUNT_MASK 0x0000ffff 58 #define BRCMF_SCAN_PARAMS_NSSID_SHIFT 16 59 60 /* scan type definitions */ 61 #define BRCMF_SCANTYPE_DEFAULT 0xFF 62 #define BRCMF_SCANTYPE_ACTIVE 0 63 #define BRCMF_SCANTYPE_PASSIVE 1 64 65 #define BRCMF_WSEC_MAX_PSK_LEN 32 66 #define BRCMF_WSEC_PASSPHRASE BIT(0) 67 68 #define BRCMF_WSEC_MAX_SAE_PASSWORD_LEN 128 69 70 /* primary (ie tx) key */ 71 #define BRCMF_PRIMARY_KEY (1 << 1) 72 #define DOT11_BSSTYPE_ANY 2 73 #define BRCMF_ESCAN_REQ_VERSION 1 74 #define BRCMF_ESCAN_REQ_VERSION_V2 2 75 76 #define BRCMF_MAXRATES_IN_SET 16 /* max # of rates in rateset */ 77 78 /* OBSS Coex Auto/On/Off */ 79 #define BRCMF_OBSS_COEX_AUTO (-1) 80 #define BRCMF_OBSS_COEX_OFF 0 81 #define BRCMF_OBSS_COEX_ON 1 82 83 /* WOWL bits */ 84 /* Wakeup on Magic packet: */ 85 #define BRCMF_WOWL_MAGIC (1 << 0) 86 /* Wakeup on Netpattern */ 87 #define BRCMF_WOWL_NET (1 << 1) 88 /* Wakeup on loss-of-link due to Disassoc/Deauth: */ 89 #define BRCMF_WOWL_DIS (1 << 2) 90 /* Wakeup on retrograde TSF: */ 91 #define BRCMF_WOWL_RETR (1 << 3) 92 /* Wakeup on loss of beacon: */ 93 #define BRCMF_WOWL_BCN (1 << 4) 94 /* Wakeup after test: */ 95 #define BRCMF_WOWL_TST (1 << 5) 96 /* Wakeup after PTK refresh: */ 97 #define BRCMF_WOWL_M1 (1 << 6) 98 /* Wakeup after receipt of EAP-Identity Req: */ 99 #define BRCMF_WOWL_EAPID (1 << 7) 100 /* Wakeind via PME(0) or GPIO(1): */ 101 #define BRCMF_WOWL_PME_GPIO (1 << 8) 102 /* need tkip phase 1 key to be updated by the driver: */ 103 #define BRCMF_WOWL_NEEDTKIP1 (1 << 9) 104 /* enable wakeup if GTK fails: */ 105 #define BRCMF_WOWL_GTK_FAILURE (1 << 10) 106 /* support extended magic packets: */ 107 #define BRCMF_WOWL_EXTMAGPAT (1 << 11) 108 /* support ARP/NS/keepalive offloading: */ 109 #define BRCMF_WOWL_ARPOFFLOAD (1 << 12) 110 /* read protocol version for EAPOL frames: */ 111 #define BRCMF_WOWL_WPA2 (1 << 13) 112 /* If the bit is set, use key rotaton: */ 113 #define BRCMF_WOWL_KEYROT (1 << 14) 114 /* If the bit is set, frm received was bcast frame: */ 115 #define BRCMF_WOWL_BCAST (1 << 15) 116 /* If the bit is set, scan offload is enabled: */ 117 #define BRCMF_WOWL_SCANOL (1 << 16) 118 /* Wakeup on tcpkeep alive timeout: */ 119 #define BRCMF_WOWL_TCPKEEP_TIME (1 << 17) 120 /* Wakeup on mDNS Conflict Resolution: */ 121 #define BRCMF_WOWL_MDNS_CONFLICT (1 << 18) 122 /* Wakeup on mDNS Service Connect: */ 123 #define BRCMF_WOWL_MDNS_SERVICE (1 << 19) 124 /* tcp keepalive got data: */ 125 #define BRCMF_WOWL_TCPKEEP_DATA (1 << 20) 126 /* Firmware died in wowl mode: */ 127 #define BRCMF_WOWL_FW_HALT (1 << 21) 128 /* Enable detection of radio button changes: */ 129 #define BRCMF_WOWL_ENAB_HWRADIO (1 << 22) 130 /* Offloads detected MIC failure(s): */ 131 #define BRCMF_WOWL_MIC_FAIL (1 << 23) 132 /* Wakeup in Unassociated state (Net/Magic Pattern): */ 133 #define BRCMF_WOWL_UNASSOC (1 << 24) 134 /* Wakeup if received matched secured pattern: */ 135 #define BRCMF_WOWL_SECURE (1 << 25) 136 /* Wakeup on finding preferred network */ 137 #define BRCMF_WOWL_PFN_FOUND (1 << 27) 138 /* Wakeup on receiving pairwise key EAP packets: */ 139 #define WIPHY_WOWL_EAP_PK (1 << 28) 140 /* Link Down indication in WoWL mode: */ 141 #define BRCMF_WOWL_LINKDOWN (1 << 31) 142 143 #define BRCMF_WOWL_MAXPATTERNS 16 144 #define BRCMF_WOWL_MAXPATTERNSIZE 128 145 146 #define BRCMF_COUNTRY_BUF_SZ 4 147 #define BRCMF_ANT_MAX 4 148 149 #define BRCMF_MAX_ASSOCLIST 128 150 151 #define BRCMF_TXBF_SU_BFE_CAP BIT(0) 152 #define BRCMF_TXBF_MU_BFE_CAP BIT(1) 153 #define BRCMF_TXBF_SU_BFR_CAP BIT(0) 154 #define BRCMF_TXBF_MU_BFR_CAP BIT(1) 155 156 #define BRCMF_MAXPMKID 16 /* max # PMKID cache entries */ 157 #define BRCMF_NUMCHANNELS 64 158 159 #define BRCMF_PFN_MACADDR_CFG_VER 1 160 #define BRCMF_PFN_MAC_OUI_ONLY BIT(0) 161 #define BRCMF_PFN_SET_MAC_UNASSOC BIT(1) 162 163 #define BRCMF_MCSSET_LEN 16 164 165 #define BRCMF_RSN_KCK_LENGTH 16 166 #define BRCMF_RSN_KEK_LENGTH 16 167 #define BRCMF_RSN_REPLAY_LEN 8 168 169 #define BRCMF_MFP_NONE 0 170 #define BRCMF_MFP_CAPABLE 1 171 #define BRCMF_MFP_REQUIRED 2 172 173 #define BRCMF_VHT_CAP_MCS_MAP_NSS_MAX 8 174 175 #define BRCMF_HE_CAP_MCS_MAP_NSS_MAX 8 176 177 #define BRCMF_PMKSA_VER_2 2 178 #define BRCMF_PMKSA_VER_3 3 179 #define BRCMF_PMKSA_NO_EXPIRY 0xffffffff 180 181 /* MAX_CHUNK_LEN is the maximum length for data passing to firmware in each 182 * ioctl. It is relatively small because firmware has small maximum size input 183 * playload restriction for ioctls. 184 */ 185 #define MAX_CHUNK_LEN 1400 186 187 #define DLOAD_HANDLER_VER 1 /* Downloader version */ 188 #define DLOAD_FLAG_VER_MASK 0xf000 /* Downloader version mask */ 189 #define DLOAD_FLAG_VER_SHIFT 12 /* Downloader version shift */ 190 191 #define DL_BEGIN 0x0002 192 #define DL_END 0x0004 193 194 #define DL_TYPE_CLM 2 195 196 /* join preference types for join_pref iovar */ 197 enum brcmf_join_pref_types { 198 BRCMF_JOIN_PREF_RSSI = 1, 199 BRCMF_JOIN_PREF_WPA, 200 BRCMF_JOIN_PREF_BAND, 201 BRCMF_JOIN_PREF_RSSI_DELTA, 202 }; 203 204 enum brcmf_fil_p2p_if_types { 205 BRCMF_FIL_P2P_IF_CLIENT, 206 BRCMF_FIL_P2P_IF_GO, 207 BRCMF_FIL_P2P_IF_DYNBCN_GO, 208 BRCMF_FIL_P2P_IF_DEV, 209 }; 210 211 enum brcmf_wowl_pattern_type { 212 BRCMF_WOWL_PATTERN_TYPE_BITMAP = 0, 213 BRCMF_WOWL_PATTERN_TYPE_ARP, 214 BRCMF_WOWL_PATTERN_TYPE_NA 215 }; 216 217 struct brcmf_fil_p2p_if_le { 218 u8 addr[ETH_ALEN]; 219 __le16 type; 220 __le16 chspec; 221 }; 222 223 struct brcmf_fil_chan_info_le { 224 __le32 hw_channel; 225 __le32 target_channel; 226 __le32 scan_channel; 227 }; 228 229 struct brcmf_fil_action_frame_le { 230 u8 da[ETH_ALEN]; 231 __le16 len; 232 __le32 packet_id; 233 u8 data[BRCMF_FIL_ACTION_FRAME_SIZE]; 234 }; 235 236 struct brcmf_fil_af_params_le { 237 __le32 channel; 238 __le32 dwell_time; 239 u8 bssid[ETH_ALEN]; 240 u8 pad[2]; 241 struct brcmf_fil_action_frame_le action_frame; 242 }; 243 244 struct brcmf_fil_bss_enable_le { 245 __le32 bsscfgidx; 246 __le32 enable; 247 }; 248 249 struct brcmf_fil_bwcap_le { 250 __le32 band; 251 __le32 bw_cap; 252 }; 253 254 /** 255 * struct tdls_iovar - common structure for tdls iovars. 256 * 257 * @ea: ether address of peer station. 258 * @mode: mode value depending on specific tdls iovar. 259 * @chanspec: channel specification. 260 * @pad: unused (for future use). 261 */ 262 struct brcmf_tdls_iovar_le { 263 u8 ea[ETH_ALEN]; /* Station address */ 264 u8 mode; /* mode: depends on iovar */ 265 __le16 chanspec; 266 __le32 pad; /* future */ 267 }; 268 269 enum brcmf_tdls_manual_ep_ops { 270 BRCMF_TDLS_MANUAL_EP_CREATE = 1, 271 BRCMF_TDLS_MANUAL_EP_DELETE = 3, 272 BRCMF_TDLS_MANUAL_EP_DISCOVERY = 6 273 }; 274 275 /* Pattern matching filter. Specifies an offset within received packets to 276 * start matching, the pattern to match, the size of the pattern, and a bitmask 277 * that indicates which bits within the pattern should be matched. 278 */ 279 struct brcmf_pkt_filter_pattern_le { 280 /* 281 * Offset within received packet to start pattern matching. 282 * Offset '0' is the first byte of the ethernet header. 283 */ 284 __le32 offset; 285 /* Size of the pattern. Bitmask must be the same size.*/ 286 __le32 size_bytes; 287 /* 288 * Variable length mask and pattern data. mask starts at offset 0. 289 * Pattern immediately follows mask. 290 */ 291 u8 mask_and_pattern[1]; 292 }; 293 294 /* IOVAR "pkt_filter_add" parameter. Used to install packet filters. */ 295 struct brcmf_pkt_filter_le { 296 __le32 id; /* Unique filter id, specified by app. */ 297 __le32 type; /* Filter type (WL_PKT_FILTER_TYPE_xxx). */ 298 __le32 negate_match; /* Negate the result of filter matches */ 299 union { /* Filter definitions */ 300 struct brcmf_pkt_filter_pattern_le pattern; /* Filter pattern */ 301 } u; 302 }; 303 304 /* IOVAR "pkt_filter_enable" parameter. */ 305 struct brcmf_pkt_filter_enable_le { 306 __le32 id; /* Unique filter id */ 307 __le32 enable; /* Enable/disable bool */ 308 }; 309 310 /* BSS info structure 311 * Applications MUST CHECK ie_offset field and length field to access IEs and 312 * next bss_info structure in a vector (in struct brcmf_scan_results) 313 */ 314 struct brcmf_bss_info_le { 315 __le32 version; /* version field */ 316 __le32 length; /* byte length of data in this record, 317 * starting at version and including IEs 318 */ 319 u8 BSSID[ETH_ALEN]; 320 __le16 beacon_period; /* units are Kusec */ 321 __le16 capability; /* Capability information */ 322 u8 SSID_len; 323 u8 SSID[32]; 324 struct { 325 __le32 count; /* # rates in this set */ 326 u8 rates[16]; /* rates in 500kbps units w/hi bit set if basic */ 327 } rateset; /* supported rates */ 328 __le16 chanspec; /* chanspec for bss */ 329 __le16 atim_window; /* units are Kusec */ 330 u8 dtim_period; /* DTIM period */ 331 __le16 RSSI; /* receive signal strength (in dBm) */ 332 s8 phy_noise; /* noise (in dBm) */ 333 334 u8 n_cap; /* BSS is 802.11N Capable */ 335 /* 802.11N BSS Capabilities (based on HT_CAP_*): */ 336 __le32 nbss_cap; 337 u8 ctl_ch; /* 802.11N BSS control channel number */ 338 __le32 reserved32[1]; /* Reserved for expansion of BSS properties */ 339 u8 flags; /* flags */ 340 u8 reserved[3]; /* Reserved for expansion of BSS properties */ 341 u8 basic_mcs[BRCMF_MCSSET_LEN]; /* 802.11N BSS required MCS set */ 342 343 __le16 ie_offset; /* offset at which IEs start, from beginning */ 344 __le32 ie_length; /* byte length of Information Elements */ 345 __le16 SNR; /* average SNR of during frame reception */ 346 /* Add new fields here */ 347 /* variable length Information Elements */ 348 }; 349 350 struct brcm_rateset_le { 351 /* # rates in this set */ 352 __le32 count; 353 /* rates in 500kbps units w/hi bit set if basic */ 354 u8 rates[BRCMF_MAXRATES_IN_SET]; 355 }; 356 357 struct brcmf_ssid_le { 358 __le32 SSID_len; 359 unsigned char SSID[IEEE80211_MAX_SSID_LEN]; 360 }; 361 362 /* Alternate SSID structure used in some places... */ 363 struct brcmf_ssid8_le { 364 u8 SSID_len; 365 unsigned char SSID[IEEE80211_MAX_SSID_LEN]; 366 }; 367 368 struct brcmf_scan_params_le { 369 struct brcmf_ssid_le ssid_le; /* default: {0, ""} */ 370 u8 bssid[ETH_ALEN]; /* default: bcast */ 371 s8 bss_type; /* default: any, 372 * DOT11_BSSTYPE_ANY/INFRASTRUCTURE/INDEPENDENT 373 */ 374 u8 scan_type; /* flags, 0 use default */ 375 __le32 nprobes; /* -1 use default, number of probes per channel */ 376 __le32 active_time; /* -1 use default, dwell time per channel for 377 * active scanning 378 */ 379 __le32 passive_time; /* -1 use default, dwell time per channel 380 * for passive scanning 381 */ 382 __le32 home_time; /* -1 use default, dwell time for the 383 * home channel between channel scans 384 */ 385 __le32 channel_num; /* count of channels and ssids that follow 386 * 387 * low half is count of channels in 388 * channel_list, 0 means default (use all 389 * available channels) 390 * 391 * high half is entries in struct brcmf_ssid 392 * array that follows channel_list, aligned for 393 * s32 (4 bytes) meaning an odd channel count 394 * implies a 2-byte pad between end of 395 * channel_list and first ssid 396 * 397 * if ssid count is zero, single ssid in the 398 * fixed parameter portion is assumed, otherwise 399 * ssid in the fixed portion is ignored 400 */ 401 __le16 channel_list[1]; /* list of chanspecs */ 402 }; 403 404 struct brcmf_scan_params_v2_le { 405 __le16 version; /* structure version */ 406 __le16 length; /* structure length */ 407 struct brcmf_ssid_le ssid_le; /* default: {0, ""} */ 408 u8 bssid[ETH_ALEN]; /* default: bcast */ 409 s8 bss_type; /* default: any, 410 * DOT11_BSSTYPE_ANY/INFRASTRUCTURE/INDEPENDENT 411 */ 412 u8 pad; 413 __le32 scan_type; /* flags, 0 use default */ 414 __le32 nprobes; /* -1 use default, number of probes per channel */ 415 __le32 active_time; /* -1 use default, dwell time per channel for 416 * active scanning 417 */ 418 __le32 passive_time; /* -1 use default, dwell time per channel 419 * for passive scanning 420 */ 421 __le32 home_time; /* -1 use default, dwell time for the 422 * home channel between channel scans 423 */ 424 __le32 channel_num; /* count of channels and ssids that follow 425 * 426 * low half is count of channels in 427 * channel_list, 0 means default (use all 428 * available channels) 429 * 430 * high half is entries in struct brcmf_ssid 431 * array that follows channel_list, aligned for 432 * s32 (4 bytes) meaning an odd channel count 433 * implies a 2-byte pad between end of 434 * channel_list and first ssid 435 * 436 * if ssid count is zero, single ssid in the 437 * fixed parameter portion is assumed, otherwise 438 * ssid in the fixed portion is ignored 439 */ 440 __le16 channel_list[1]; /* list of chanspecs */ 441 }; 442 443 struct brcmf_scan_results { 444 u32 buflen; 445 u32 version; 446 u32 count; 447 struct brcmf_bss_info_le bss_info_le[]; 448 }; 449 450 struct brcmf_escan_params_le { 451 __le32 version; 452 __le16 action; 453 __le16 sync_id; 454 union { 455 struct brcmf_scan_params_le params_le; 456 struct brcmf_scan_params_v2_le params_v2_le; 457 }; 458 }; 459 460 struct brcmf_escan_result_le { 461 __le32 buflen; 462 __le32 version; 463 __le16 sync_id; 464 __le16 bss_count; 465 struct brcmf_bss_info_le bss_info_le; 466 }; 467 468 #define WL_ESCAN_RESULTS_FIXED_SIZE (sizeof(struct brcmf_escan_result_le) - \ 469 sizeof(struct brcmf_bss_info_le)) 470 471 /* used for association with a specific BSSID and chanspec list */ 472 struct brcmf_assoc_params_le { 473 /* 00:00:00:00:00:00: broadcast scan */ 474 u8 bssid[ETH_ALEN]; 475 /* 0: all available channels, otherwise count of chanspecs in 476 * chanspec_list */ 477 __le32 chanspec_num; 478 /* list of chanspecs */ 479 __le16 chanspec_list[1]; 480 }; 481 482 /** 483 * struct join_pref params - parameters for preferred join selection. 484 * 485 * @type: preference type (see enum brcmf_join_pref_types). 486 * @len: length of bytes following (currently always 2). 487 * @rssi_gain: signal gain for selection (only when @type is RSSI_DELTA). 488 * @band: band to which selection preference applies. 489 * This is used if @type is BAND or RSSI_DELTA. 490 */ 491 struct brcmf_join_pref_params { 492 u8 type; 493 u8 len; 494 u8 rssi_gain; 495 u8 band; 496 }; 497 498 /* used for join with or without a specific bssid and channel list */ 499 struct brcmf_join_params { 500 struct brcmf_ssid_le ssid_le; 501 struct brcmf_assoc_params_le params_le; 502 }; 503 504 /* scan params for extended join */ 505 struct brcmf_join_scan_params_le { 506 u8 scan_type; /* 0 use default, active or passive scan */ 507 __le32 nprobes; /* -1 use default, nr of probes per channel */ 508 __le32 active_time; /* -1 use default, dwell time per channel for 509 * active scanning 510 */ 511 __le32 passive_time; /* -1 use default, dwell time per channel 512 * for passive scanning 513 */ 514 __le32 home_time; /* -1 use default, dwell time for the home 515 * channel between channel scans 516 */ 517 }; 518 519 /* extended join params */ 520 struct brcmf_ext_join_params_le { 521 struct brcmf_ssid_le ssid_le; /* {0, ""}: wildcard scan */ 522 struct brcmf_join_scan_params_le scan_le; 523 struct brcmf_assoc_params_le assoc_le; 524 }; 525 526 struct brcmf_wsec_key { 527 u32 index; /* key index */ 528 u32 len; /* key length */ 529 u8 data[WLAN_MAX_KEY_LEN]; /* key data */ 530 u32 pad_1[18]; 531 u32 algo; /* CRYPTO_ALGO_AES_CCM, CRYPTO_ALGO_WEP128, etc */ 532 u32 flags; /* misc flags */ 533 u32 pad_2[3]; 534 u32 iv_initialized; /* has IV been initialized already? */ 535 u32 pad_3; 536 /* Rx IV */ 537 struct { 538 u32 hi; /* upper 32 bits of IV */ 539 u16 lo; /* lower 16 bits of IV */ 540 } rxiv; 541 u32 pad_4[2]; 542 u8 ea[ETH_ALEN]; /* per station */ 543 }; 544 545 /* 546 * dongle requires same struct as above but with fields in little endian order 547 */ 548 struct brcmf_wsec_key_le { 549 __le32 index; /* key index */ 550 __le32 len; /* key length */ 551 u8 data[WLAN_MAX_KEY_LEN]; /* key data */ 552 __le32 pad_1[18]; 553 __le32 algo; /* CRYPTO_ALGO_AES_CCM, CRYPTO_ALGO_WEP128, etc */ 554 __le32 flags; /* misc flags */ 555 __le32 pad_2[3]; 556 __le32 iv_initialized; /* has IV been initialized already? */ 557 __le32 pad_3; 558 /* Rx IV */ 559 struct { 560 __le32 hi; /* upper 32 bits of IV */ 561 __le16 lo; /* lower 16 bits of IV */ 562 } rxiv; 563 __le32 pad_4[2]; 564 u8 ea[ETH_ALEN]; /* per station */ 565 }; 566 567 /** 568 * struct brcmf_wsec_pmk_le - firmware pmk material. 569 * 570 * @key_len: number of octets in key material. 571 * @flags: key handling qualifiers. 572 * @key: PMK key material. 573 */ 574 struct brcmf_wsec_pmk_le { 575 __le16 key_len; 576 __le16 flags; 577 u8 key[2 * BRCMF_WSEC_MAX_PSK_LEN + 1]; 578 }; 579 580 /** 581 * struct brcmf_wsec_sae_pwd_le - firmware SAE password material. 582 * 583 * @key_len: number of octets in key materials. 584 * @key: SAE password material. 585 */ 586 struct brcmf_wsec_sae_pwd_le { 587 __le16 key_len; 588 u8 key[BRCMF_WSEC_MAX_SAE_PASSWORD_LEN]; 589 }; 590 591 /* Used to get specific STA parameters */ 592 struct brcmf_scb_val_le { 593 __le32 val; 594 u8 ea[ETH_ALEN]; 595 }; 596 597 /* channel encoding */ 598 struct brcmf_channel_info_le { 599 __le32 hw_channel; 600 __le32 target_channel; 601 __le32 scan_channel; 602 }; 603 604 struct brcmf_sta_info_le { 605 __le16 ver; /* version of this struct */ 606 __le16 len; /* length in bytes of this structure */ 607 __le16 cap; /* sta's advertised capabilities */ 608 __le32 flags; /* flags defined below */ 609 __le32 idle; /* time since data pkt rx'd from sta */ 610 u8 ea[ETH_ALEN]; /* Station address */ 611 __le32 count; /* # rates in this set */ 612 u8 rates[BRCMF_MAXRATES_IN_SET]; /* rates in 500kbps units */ 613 /* w/hi bit set if basic */ 614 __le32 in; /* seconds elapsed since associated */ 615 __le32 listen_interval_inms; /* Min Listen interval in ms for STA */ 616 617 /* Fields valid for ver >= 3 */ 618 __le32 tx_pkts; /* # of packets transmitted */ 619 __le32 tx_failures; /* # of packets failed */ 620 __le32 rx_ucast_pkts; /* # of unicast packets received */ 621 __le32 rx_mcast_pkts; /* # of multicast packets received */ 622 __le32 tx_rate; /* Rate of last successful tx frame */ 623 __le32 rx_rate; /* Rate of last successful rx frame */ 624 __le32 rx_decrypt_succeeds; /* # of packet decrypted successfully */ 625 __le32 rx_decrypt_failures; /* # of packet decrypted failed */ 626 627 /* Fields valid for ver >= 4 */ 628 __le32 tx_tot_pkts; /* # of tx pkts (ucast + mcast) */ 629 __le32 rx_tot_pkts; /* # of data packets recvd (uni + mcast) */ 630 __le32 tx_mcast_pkts; /* # of mcast pkts txed */ 631 __le64 tx_tot_bytes; /* data bytes txed (ucast + mcast) */ 632 __le64 rx_tot_bytes; /* data bytes recvd (ucast + mcast) */ 633 __le64 tx_ucast_bytes; /* data bytes txed (ucast) */ 634 __le64 tx_mcast_bytes; /* # data bytes txed (mcast) */ 635 __le64 rx_ucast_bytes; /* data bytes recvd (ucast) */ 636 __le64 rx_mcast_bytes; /* data bytes recvd (mcast) */ 637 s8 rssi[BRCMF_ANT_MAX]; /* per antenna rssi */ 638 s8 nf[BRCMF_ANT_MAX]; /* per antenna noise floor */ 639 __le16 aid; /* association ID */ 640 __le16 ht_capabilities; /* advertised ht caps */ 641 __le16 vht_flags; /* converted vht flags */ 642 __le32 tx_pkts_retry_cnt; /* # of frames where a retry was 643 * exhausted. 644 */ 645 __le32 tx_pkts_retry_exhausted; /* # of user frames where a retry 646 * was exhausted 647 */ 648 s8 rx_lastpkt_rssi[BRCMF_ANT_MAX]; /* Per antenna RSSI of last 649 * received data frame. 650 */ 651 /* TX WLAN retry/failure statistics: 652 * Separated for host requested frames and locally generated frames. 653 * Include unicast frame only where the retries/failures can be counted. 654 */ 655 __le32 tx_pkts_total; /* # user frames sent successfully */ 656 __le32 tx_pkts_retries; /* # user frames retries */ 657 __le32 tx_pkts_fw_total; /* # FW generated sent successfully */ 658 __le32 tx_pkts_fw_retries; /* # retries for FW generated frames */ 659 __le32 tx_pkts_fw_retry_exhausted; /* # FW generated where a retry 660 * was exhausted 661 */ 662 __le32 rx_pkts_retried; /* # rx with retry bit set */ 663 __le32 tx_rate_fallback; /* lowest fallback TX rate */ 664 665 union { 666 struct { 667 struct { 668 __le32 count; /* # rates in this set */ 669 u8 rates[BRCMF_MAXRATES_IN_SET]; /* rates in 500kbps units w/hi bit set if basic */ 670 u8 mcs[BRCMF_MCSSET_LEN]; /* supported mcs index bit map */ 671 __le16 vht_mcs[BRCMF_VHT_CAP_MCS_MAP_NSS_MAX]; /* supported mcs index bit map per nss */ 672 } rateset_adv; 673 } v5; 674 675 struct { 676 __le32 rx_dur_total; /* total user RX duration (estimated) */ 677 __le16 chanspec; /** chanspec this sta is on */ 678 __le16 pad_1; 679 struct { 680 __le16 version; /* version */ 681 __le16 len; /* length */ 682 __le32 count; /* # rates in this set */ 683 u8 rates[BRCMF_MAXRATES_IN_SET]; /* rates in 500kbps units w/hi bit set if basic */ 684 u8 mcs[BRCMF_MCSSET_LEN]; /* supported mcs index bit map */ 685 __le16 vht_mcs[BRCMF_VHT_CAP_MCS_MAP_NSS_MAX]; /* supported mcs index bit map per nss */ 686 __le16 he_mcs[BRCMF_HE_CAP_MCS_MAP_NSS_MAX]; /* supported he mcs index bit map per nss */ 687 } rateset_adv; /* rateset along with mcs index bitmap */ 688 __le16 wpauth; /* authentication type */ 689 u8 algo; /* crypto algorithm */ 690 u8 pad_2; 691 __le32 tx_rspec; /* Rate of last successful tx frame */ 692 __le32 rx_rspec; /* Rate of last successful rx frame */ 693 __le32 wnm_cap; /* wnm capabilities */ 694 } v7; 695 }; 696 }; 697 698 struct brcmf_chanspec_list { 699 __le32 count; /* # of entries */ 700 __le32 element[1]; /* variable length uint32 list */ 701 }; 702 703 /* 704 * WLC_E_PROBRESP_MSG 705 * WLC_E_P2P_PROBREQ_MSG 706 * WLC_E_ACTION_FRAME_RX 707 */ 708 struct brcmf_rx_mgmt_data { 709 __be16 version; 710 __be16 chanspec; 711 __be32 rssi; 712 __be32 mactime; 713 __be32 rate; 714 }; 715 716 /** 717 * struct brcmf_fil_wowl_pattern_le - wowl pattern configuration struct. 718 * 719 * @cmd: "add", "del" or "clr". 720 * @masksize: Size of the mask in #of bytes 721 * @offset: Pattern byte offset in packet 722 * @patternoffset: Offset of start of pattern. Starting from field masksize. 723 * @patternsize: Size of the pattern itself in #of bytes 724 * @id: id 725 * @reasonsize: Size of the wakeup reason code 726 * @type: Type of pattern (enum brcmf_wowl_pattern_type) 727 */ 728 struct brcmf_fil_wowl_pattern_le { 729 u8 cmd[4]; 730 __le32 masksize; 731 __le32 offset; 732 __le32 patternoffset; 733 __le32 patternsize; 734 __le32 id; 735 __le32 reasonsize; 736 __le32 type; 737 /* u8 mask[] - Mask follows the structure above */ 738 /* u8 pattern[] - Pattern follows the mask is at 'patternoffset' */ 739 }; 740 741 struct brcmf_mbss_ssid_le { 742 __le32 bsscfgidx; 743 __le32 SSID_len; 744 unsigned char SSID[32]; 745 }; 746 747 /** 748 * struct brcmf_fil_country_le - country configuration structure. 749 * 750 * @country_abbrev: null-terminated country code used in the country IE. 751 * @rev: revision specifier for ccode. on set, -1 indicates unspecified. 752 * @ccode: null-terminated built-in country code. 753 */ 754 struct brcmf_fil_country_le { 755 char country_abbrev[BRCMF_COUNTRY_BUF_SZ]; 756 __le32 rev; 757 char ccode[BRCMF_COUNTRY_BUF_SZ]; 758 }; 759 760 /** 761 * struct brcmf_rev_info_le - device revision info. 762 * 763 * @vendorid: PCI vendor id. 764 * @deviceid: device id of chip. 765 * @radiorev: radio revision. 766 * @chiprev: chip revision. 767 * @corerev: core revision. 768 * @boardid: board identifier (usu. PCI sub-device id). 769 * @boardvendor: board vendor (usu. PCI sub-vendor id). 770 * @boardrev: board revision. 771 * @driverrev: driver version. 772 * @ucoderev: microcode version. 773 * @bus: bus type. 774 * @chipnum: chip number. 775 * @phytype: phy type. 776 * @phyrev: phy revision. 777 * @anarev: anacore rev. 778 * @chippkg: chip package info. 779 * @nvramrev: nvram revision number. 780 */ 781 struct brcmf_rev_info_le { 782 __le32 vendorid; 783 __le32 deviceid; 784 __le32 radiorev; 785 __le32 chiprev; 786 __le32 corerev; 787 __le32 boardid; 788 __le32 boardvendor; 789 __le32 boardrev; 790 __le32 driverrev; 791 __le32 ucoderev; 792 __le32 bus; 793 __le32 chipnum; 794 __le32 phytype; 795 __le32 phyrev; 796 __le32 anarev; 797 __le32 chippkg; 798 __le32 nvramrev; 799 }; 800 801 /** 802 * struct brcmf_wlc_version_le - firmware revision info. 803 * 804 * @version: structure version. 805 * @length: structure length. 806 * @epi_ver_major: EPI major version 807 * @epi_ver_minor: EPI minor version 808 * @epi_ver_rc: EPI rc version 809 * @epi_ver_incr: EPI increment version 810 * @wlc_ver_major: WLC major version 811 * @wlc_ver_minor: WLC minor version 812 */ 813 struct brcmf_wlc_version_le { 814 __le16 version; 815 __le16 length; 816 817 __le16 epi_ver_major; 818 __le16 epi_ver_minor; 819 __le16 epi_ver_rc; 820 __le16 epi_ver_incr; 821 822 __le16 wlc_ver_major; 823 __le16 wlc_ver_minor; 824 }; 825 826 /** 827 * struct brcmf_assoclist_le - request assoc list. 828 * 829 * @count: indicates number of stations. 830 * @mac: MAC addresses of stations. 831 */ 832 struct brcmf_assoclist_le { 833 __le32 count; 834 u8 mac[BRCMF_MAX_ASSOCLIST][ETH_ALEN]; 835 }; 836 837 /** 838 * struct brcmf_rssi_be - RSSI threshold event format 839 * 840 * @rssi: receive signal strength (in dBm) 841 * @snr: signal-noise ratio 842 * @noise: noise (in dBm) 843 */ 844 struct brcmf_rssi_be { 845 __be32 rssi; 846 __be32 snr; 847 __be32 noise; 848 }; 849 850 #define BRCMF_MAX_RSSI_LEVELS 8 851 852 /** 853 * struct brcm_rssi_event_le - rssi_event IOVAR format 854 * 855 * @rate_limit_msec: RSSI event rate limit 856 * @rssi_level_num: number of supplied RSSI levels 857 * @rssi_levels: RSSI levels in ascending order 858 */ 859 struct brcmf_rssi_event_le { 860 __le32 rate_limit_msec; 861 s8 rssi_level_num; 862 s8 rssi_levels[BRCMF_MAX_RSSI_LEVELS]; 863 }; 864 865 /** 866 * struct brcmf_wowl_wakeind_le - Wakeup indicators 867 * Note: note both fields contain same information. 868 * 869 * @pci_wakeind: Whether PCI PMECSR PMEStatus bit was set. 870 * @ucode_wakeind: What wakeup-event indication was set by ucode 871 */ 872 struct brcmf_wowl_wakeind_le { 873 __le32 pci_wakeind; 874 __le32 ucode_wakeind; 875 }; 876 877 /** 878 * struct brcmf_pmksa - PMK Security Association 879 * 880 * @bssid: The AP's BSSID. 881 * @pmkid: he PMK material itself. 882 */ 883 struct brcmf_pmksa { 884 u8 bssid[ETH_ALEN]; 885 u8 pmkid[WLAN_PMKID_LEN]; 886 }; 887 888 /** 889 * struct brcmf_pmksa_v2 - PMK Security Association 890 * 891 * @length: Length of the structure. 892 * @bssid: The AP's BSSID. 893 * @pmkid: The PMK ID. 894 * @pmk: PMK material for FILS key derivation. 895 * @pmk_len: Length of PMK data. 896 * @ssid: The AP's SSID. 897 * @fils_cache_id: FILS cache identifier 898 */ 899 struct brcmf_pmksa_v2 { 900 __le16 length; 901 u8 bssid[ETH_ALEN]; 902 u8 pmkid[WLAN_PMKID_LEN]; 903 u8 pmk[WLAN_PMK_LEN_SUITE_B_192]; 904 __le16 pmk_len; 905 struct brcmf_ssid8_le ssid; 906 u16 fils_cache_id; 907 }; 908 909 /** 910 * struct brcmf_pmksa_v3 - PMK Security Association 911 * 912 * @bssid: The AP's BSSID. 913 * @pmkid: The PMK ID. 914 * @pmkid_len: The length of the PMK ID. 915 * @pmk: PMK material for FILS key derivation. 916 * @pmk_len: Length of PMK data. 917 * @fils_cache_id: FILS cache identifier 918 * @ssid: The AP's SSID. 919 * @time_left: Remaining time until expiry. 0 = expired, ~0 = no expiry. 920 */ 921 struct brcmf_pmksa_v3 { 922 u8 bssid[ETH_ALEN]; 923 u8 pmkid[WLAN_PMKID_LEN]; 924 u8 pmkid_len; 925 u8 pmk[WLAN_PMK_LEN_SUITE_B_192]; 926 u8 pmk_len; 927 __le16 fils_cache_id; 928 u8 pad; 929 struct brcmf_ssid8_le ssid; 930 __le32 time_left; 931 }; 932 933 /** 934 * struct brcmf_pmk_list_le - List of pmksa's. 935 * 936 * @npmk: Number of pmksa's. 937 * @pmk: PMK SA information. 938 */ 939 struct brcmf_pmk_list_le { 940 __le32 npmk; 941 struct brcmf_pmksa pmk[BRCMF_MAXPMKID]; 942 }; 943 944 /** 945 * struct brcmf_pmk_list_v2_le - List of pmksa's. 946 * 947 * @version: Request version. 948 * @length: Length of this structure. 949 * @pmk: PMK SA information. 950 */ 951 struct brcmf_pmk_list_v2_le { 952 __le16 version; 953 __le16 length; 954 struct brcmf_pmksa_v2 pmk[BRCMF_MAXPMKID]; 955 }; 956 957 /** 958 * struct brcmf_pmk_op_v3_le - Operation on PMKSA list. 959 * 960 * @version: Request version. 961 * @length: Length of this structure. 962 * @pmk: PMK SA information. 963 */ 964 struct brcmf_pmk_op_v3_le { 965 __le16 version; 966 __le16 length; 967 __le16 count; 968 __le16 pad; 969 struct brcmf_pmksa_v3 pmk[BRCMF_MAXPMKID]; 970 }; 971 972 /** 973 * struct brcmf_pno_param_le - PNO scan configuration parameters 974 * 975 * @version: PNO parameters version. 976 * @scan_freq: scan frequency. 977 * @lost_network_timeout: #sec. to declare discovered network as lost. 978 * @flags: Bit field to control features of PFN such as sort criteria auto 979 * enable switch and background scan. 980 * @rssi_margin: Margin to avoid jitter for choosing a PFN based on RSSI sort 981 * criteria. 982 * @bestn: number of best networks in each scan. 983 * @mscan: number of scans recorded. 984 * @repeat: minimum number of scan intervals before scan frequency changes 985 * in adaptive scan. 986 * @exp: exponent of 2 for maximum scan interval. 987 * @slow_freq: slow scan period. 988 */ 989 struct brcmf_pno_param_le { 990 __le32 version; 991 __le32 scan_freq; 992 __le32 lost_network_timeout; 993 __le16 flags; 994 __le16 rssi_margin; 995 u8 bestn; 996 u8 mscan; 997 u8 repeat; 998 u8 exp; 999 __le32 slow_freq; 1000 }; 1001 1002 /** 1003 * struct brcmf_pno_config_le - PNO channel configuration. 1004 * 1005 * @reporttype: determines what is reported. 1006 * @channel_num: number of channels specified in @channel_list. 1007 * @channel_list: channels to use in PNO scan. 1008 * @flags: reserved. 1009 */ 1010 struct brcmf_pno_config_le { 1011 __le32 reporttype; 1012 __le32 channel_num; 1013 __le16 channel_list[BRCMF_NUMCHANNELS]; 1014 __le32 flags; 1015 }; 1016 1017 /** 1018 * struct brcmf_pno_net_param_le - scan parameters per preferred network. 1019 * 1020 * @ssid: ssid name and its length. 1021 * @flags: bit2: hidden. 1022 * @infra: BSS vs IBSS. 1023 * @auth: Open vs Closed. 1024 * @wpa_auth: WPA type. 1025 * @wsec: wsec value. 1026 */ 1027 struct brcmf_pno_net_param_le { 1028 struct brcmf_ssid_le ssid; 1029 __le32 flags; 1030 __le32 infra; 1031 __le32 auth; 1032 __le32 wpa_auth; 1033 __le32 wsec; 1034 }; 1035 1036 /** 1037 * struct brcmf_pno_net_info_le - information per found network. 1038 * 1039 * @bssid: BSS network identifier. 1040 * @channel: channel number only. 1041 * @SSID_len: length of ssid. 1042 * @SSID: ssid characters. 1043 * @RSSI: receive signal strength (in dBm). 1044 * @timestamp: age in seconds. 1045 */ 1046 struct brcmf_pno_net_info_le { 1047 u8 bssid[ETH_ALEN]; 1048 u8 channel; 1049 u8 SSID_len; 1050 u8 SSID[32]; 1051 __le16 RSSI; 1052 __le16 timestamp; 1053 }; 1054 1055 /** 1056 * struct brcmf_pno_scanresults_le - result returned in PNO NET FOUND event. 1057 * 1058 * @version: PNO version identifier. 1059 * @status: indicates completion status of PNO scan. 1060 * @count: amount of brcmf_pno_net_info_le entries appended. 1061 */ 1062 struct brcmf_pno_scanresults_le { 1063 __le32 version; 1064 __le32 status; 1065 __le32 count; 1066 }; 1067 1068 struct brcmf_pno_scanresults_v2_le { 1069 __le32 version; 1070 __le32 status; 1071 __le32 count; 1072 __le32 scan_ch_bucket; 1073 }; 1074 1075 /** 1076 * struct brcmf_pno_macaddr_le - to configure PNO macaddr randomization. 1077 * 1078 * @version: PNO version identifier. 1079 * @flags: Flags defining how mac addrss should be used. 1080 * @mac: MAC address. 1081 */ 1082 struct brcmf_pno_macaddr_le { 1083 u8 version; 1084 u8 flags; 1085 u8 mac[ETH_ALEN]; 1086 }; 1087 1088 /** 1089 * struct brcmf_dload_data_le - data passing to firmware for downloading 1090 * @flag: flags related to download data. 1091 * @dload_type: type of download data. 1092 * @len: length in bytes of download data. 1093 * @crc: crc of download data. 1094 * @data: download data. 1095 */ 1096 struct brcmf_dload_data_le { 1097 __le16 flag; 1098 __le16 dload_type; 1099 __le32 len; 1100 __le32 crc; 1101 u8 data[]; 1102 }; 1103 1104 /** 1105 * struct brcmf_pno_bssid_le - bssid configuration for PNO scan. 1106 * 1107 * @bssid: BSS network identifier. 1108 * @flags: flags for this BSSID. 1109 */ 1110 struct brcmf_pno_bssid_le { 1111 u8 bssid[ETH_ALEN]; 1112 __le16 flags; 1113 }; 1114 1115 /** 1116 * struct brcmf_pktcnt_le - packet counters. 1117 * 1118 * @rx_good_pkt: packets (MSDUs & MMPDUs) received from this station 1119 * @rx_bad_pkt: failed rx packets 1120 * @tx_good_pkt: packets (MSDUs & MMPDUs) transmitted to this station 1121 * @tx_bad_pkt: failed tx packets 1122 * @rx_ocast_good_pkt: unicast packets destined for others 1123 */ 1124 struct brcmf_pktcnt_le { 1125 __le32 rx_good_pkt; 1126 __le32 rx_bad_pkt; 1127 __le32 tx_good_pkt; 1128 __le32 tx_bad_pkt; 1129 __le32 rx_ocast_good_pkt; 1130 }; 1131 1132 /** 1133 * struct brcmf_gtk_keyinfo_le - GTP rekey data 1134 * 1135 * @kck: key confirmation key. 1136 * @kek: key encryption key. 1137 * @replay_counter: replay counter. 1138 */ 1139 struct brcmf_gtk_keyinfo_le { 1140 u8 kck[BRCMF_RSN_KCK_LENGTH]; 1141 u8 kek[BRCMF_RSN_KEK_LENGTH]; 1142 u8 replay_counter[BRCMF_RSN_REPLAY_LEN]; 1143 }; 1144 1145 #define BRCMF_PNO_REPORT_NO_BATCH BIT(2) 1146 1147 /** 1148 * struct brcmf_gscan_bucket_config - configuration data for channel bucket. 1149 * 1150 * @bucket_end_index: last channel index in @channel_list in 1151 * @struct brcmf_pno_config_le. 1152 * @bucket_freq_multiple: scan interval expressed in N * @scan_freq. 1153 * @flag: channel bucket report flags. 1154 * @reserved: for future use. 1155 * @repeat: number of scan at interval for exponential scan. 1156 * @max_freq_multiple: maximum scan interval for exponential scan. 1157 */ 1158 struct brcmf_gscan_bucket_config { 1159 u8 bucket_end_index; 1160 u8 bucket_freq_multiple; 1161 u8 flag; 1162 u8 reserved; 1163 __le16 repeat; 1164 __le16 max_freq_multiple; 1165 }; 1166 1167 /* version supported which must match firmware */ 1168 #define BRCMF_GSCAN_CFG_VERSION 2 1169 1170 /** 1171 * enum brcmf_gscan_cfg_flags - bit values for gscan flags. 1172 * 1173 * @BRCMF_GSCAN_CFG_FLAGS_ALL_RESULTS: send probe responses/beacons to host. 1174 * @BRCMF_GSCAN_CFG_ALL_BUCKETS_IN_1ST_SCAN: all buckets will be included in 1175 * first scan cycle. 1176 * @BRCMF_GSCAN_CFG_FLAGS_CHANGE_ONLY: indicated only flags member is changed. 1177 */ 1178 enum brcmf_gscan_cfg_flags { 1179 BRCMF_GSCAN_CFG_FLAGS_ALL_RESULTS = BIT(0), 1180 BRCMF_GSCAN_CFG_ALL_BUCKETS_IN_1ST_SCAN = BIT(3), 1181 BRCMF_GSCAN_CFG_FLAGS_CHANGE_ONLY = BIT(7), 1182 }; 1183 1184 /** 1185 * struct brcmf_gscan_config - configuration data for gscan. 1186 * 1187 * @version: version of the api to match firmware. 1188 * @flags: flags according %enum brcmf_gscan_cfg_flags. 1189 * @buffer_threshold: percentage threshold of buffer to generate an event. 1190 * @swc_nbssid_threshold: number of BSSIDs with significant change that 1191 * will generate an event. 1192 * @swc_rssi_window_size: size of rssi cache buffer (max=8). 1193 * @count_of_channel_buckets: number of array members in @bucket. 1194 * @retry_threshold: !unknown! 1195 * @lost_ap_window: !unknown! 1196 * @bucket: array of channel buckets. 1197 */ 1198 struct brcmf_gscan_config { 1199 __le16 version; 1200 u8 flags; 1201 u8 buffer_threshold; 1202 u8 swc_nbssid_threshold; 1203 u8 swc_rssi_window_size; 1204 u8 count_of_channel_buckets; 1205 u8 retry_threshold; 1206 __le16 lost_ap_window; 1207 struct brcmf_gscan_bucket_config bucket[]; 1208 }; 1209 1210 /** 1211 * struct brcmf_mkeep_alive_pkt_le - configuration data for keep-alive frame. 1212 * 1213 * @version: version for mkeep_alive 1214 * @length: length of fixed parameters in the structure. 1215 * @period_msec: keep-alive period in milliseconds. 1216 * @len_bytes: size of the data. 1217 * @keep_alive_id: ID (0 - 3). 1218 * @data: keep-alive frame data. 1219 */ 1220 struct brcmf_mkeep_alive_pkt_le { 1221 __le16 version; 1222 __le16 length; 1223 __le32 period_msec; 1224 __le16 len_bytes; 1225 u8 keep_alive_id; 1226 u8 data[]; 1227 } __packed; 1228 1229 #endif /* FWIL_TYPES_H_ */ 1230