1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 4 Broadcom B43 wireless driver 5 6 Copyright (c) 2005 Martin Langer <martin-langer@gmx.de> 7 Copyright (c) 2005 Stefano Brivio <stefano.brivio@polimi.it> 8 Copyright (c) 2005-2009 Michael Buesch <m@bues.ch> 9 Copyright (c) 2005 Danny van Dyk <kugelfang@gentoo.org> 10 Copyright (c) 2005 Andreas Jaggi <andreas.jaggi@waterwave.ch> 11 Copyright (c) 2010-2011 Rafał Miłecki <zajec5@gmail.com> 12 13 SDIO support 14 Copyright (c) 2009 Albert Herranz <albert_herranz@yahoo.es> 15 16 Some parts of the code in this file are derived from the ipw2200 17 driver Copyright(c) 2003 - 2004 Intel Corporation. 18 19 20 */ 21 22 #include <linux/delay.h> 23 #include <linux/init.h> 24 #include <linux/module.h> 25 #include <linux/if_arp.h> 26 #include <linux/etherdevice.h> 27 #include <linux/firmware.h> 28 #include <linux/workqueue.h> 29 #include <linux/skbuff.h> 30 #include <linux/io.h> 31 #include <linux/dma-mapping.h> 32 #include <linux/slab.h> 33 #include <asm/unaligned.h> 34 35 #include "b43.h" 36 #include "main.h" 37 #include "debugfs.h" 38 #include "phy_common.h" 39 #include "phy_g.h" 40 #include "phy_n.h" 41 #include "dma.h" 42 #include "pio.h" 43 #include "sysfs.h" 44 #include "xmit.h" 45 #include "lo.h" 46 #include "sdio.h" 47 #include <linux/mmc/sdio_func.h> 48 49 MODULE_DESCRIPTION("Broadcom B43 wireless driver"); 50 MODULE_AUTHOR("Martin Langer"); 51 MODULE_AUTHOR("Stefano Brivio"); 52 MODULE_AUTHOR("Michael Buesch"); 53 MODULE_AUTHOR("Gábor Stefanik"); 54 MODULE_AUTHOR("Rafał Miłecki"); 55 MODULE_LICENSE("GPL"); 56 57 MODULE_FIRMWARE("b43/ucode11.fw"); 58 MODULE_FIRMWARE("b43/ucode13.fw"); 59 MODULE_FIRMWARE("b43/ucode14.fw"); 60 MODULE_FIRMWARE("b43/ucode15.fw"); 61 MODULE_FIRMWARE("b43/ucode16_lp.fw"); 62 MODULE_FIRMWARE("b43/ucode16_mimo.fw"); 63 MODULE_FIRMWARE("b43/ucode24_lcn.fw"); 64 MODULE_FIRMWARE("b43/ucode25_lcn.fw"); 65 MODULE_FIRMWARE("b43/ucode25_mimo.fw"); 66 MODULE_FIRMWARE("b43/ucode26_mimo.fw"); 67 MODULE_FIRMWARE("b43/ucode29_mimo.fw"); 68 MODULE_FIRMWARE("b43/ucode33_lcn40.fw"); 69 MODULE_FIRMWARE("b43/ucode30_mimo.fw"); 70 MODULE_FIRMWARE("b43/ucode5.fw"); 71 MODULE_FIRMWARE("b43/ucode40.fw"); 72 MODULE_FIRMWARE("b43/ucode42.fw"); 73 MODULE_FIRMWARE("b43/ucode9.fw"); 74 75 static int modparam_bad_frames_preempt; 76 module_param_named(bad_frames_preempt, modparam_bad_frames_preempt, int, 0444); 77 MODULE_PARM_DESC(bad_frames_preempt, 78 "enable(1) / disable(0) Bad Frames Preemption"); 79 80 static char modparam_fwpostfix[16]; 81 module_param_string(fwpostfix, modparam_fwpostfix, 16, 0444); 82 MODULE_PARM_DESC(fwpostfix, "Postfix for the .fw files to load."); 83 84 static int modparam_hwpctl; 85 module_param_named(hwpctl, modparam_hwpctl, int, 0444); 86 MODULE_PARM_DESC(hwpctl, "Enable hardware-side power control (default off)"); 87 88 static int modparam_nohwcrypt; 89 module_param_named(nohwcrypt, modparam_nohwcrypt, int, 0444); 90 MODULE_PARM_DESC(nohwcrypt, "Disable hardware encryption."); 91 92 static int modparam_hwtkip; 93 module_param_named(hwtkip, modparam_hwtkip, int, 0444); 94 MODULE_PARM_DESC(hwtkip, "Enable hardware tkip."); 95 96 static int modparam_qos = 1; 97 module_param_named(qos, modparam_qos, int, 0444); 98 MODULE_PARM_DESC(qos, "Enable QOS support (default on)"); 99 100 static int modparam_btcoex = 1; 101 module_param_named(btcoex, modparam_btcoex, int, 0444); 102 MODULE_PARM_DESC(btcoex, "Enable Bluetooth coexistence (default on)"); 103 104 int b43_modparam_verbose = B43_VERBOSITY_DEFAULT; 105 module_param_named(verbose, b43_modparam_verbose, int, 0644); 106 MODULE_PARM_DESC(verbose, "Log message verbosity: 0=error, 1=warn, 2=info(default), 3=debug"); 107 108 static int b43_modparam_pio = 0; 109 module_param_named(pio, b43_modparam_pio, int, 0644); 110 MODULE_PARM_DESC(pio, "Use PIO accesses by default: 0=DMA, 1=PIO"); 111 112 static int modparam_allhwsupport = !IS_ENABLED(CONFIG_BRCMSMAC); 113 module_param_named(allhwsupport, modparam_allhwsupport, int, 0444); 114 MODULE_PARM_DESC(allhwsupport, "Enable support for all hardware (even it if overlaps with the brcmsmac driver)"); 115 116 #ifdef CONFIG_B43_BCMA 117 static const struct bcma_device_id b43_bcma_tbl[] = { 118 BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x11, BCMA_ANY_CLASS), 119 BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x15, BCMA_ANY_CLASS), 120 BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x17, BCMA_ANY_CLASS), 121 BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x18, BCMA_ANY_CLASS), 122 BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x1C, BCMA_ANY_CLASS), 123 BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x1D, BCMA_ANY_CLASS), 124 BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x1E, BCMA_ANY_CLASS), 125 BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x28, BCMA_ANY_CLASS), 126 BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x2A, BCMA_ANY_CLASS), 127 {}, 128 }; 129 MODULE_DEVICE_TABLE(bcma, b43_bcma_tbl); 130 #endif 131 132 #ifdef CONFIG_B43_SSB 133 static const struct ssb_device_id b43_ssb_tbl[] = { 134 SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 5), 135 SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 6), 136 SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 7), 137 SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 9), 138 SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 10), 139 SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 11), 140 SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 12), 141 SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 13), 142 SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 15), 143 SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 16), 144 {}, 145 }; 146 MODULE_DEVICE_TABLE(ssb, b43_ssb_tbl); 147 #endif 148 149 /* Channel and ratetables are shared for all devices. 150 * They can't be const, because ieee80211 puts some precalculated 151 * data in there. This data is the same for all devices, so we don't 152 * get concurrency issues */ 153 #define RATETAB_ENT(_rateid, _flags) \ 154 { \ 155 .bitrate = B43_RATE_TO_BASE100KBPS(_rateid), \ 156 .hw_value = (_rateid), \ 157 .flags = (_flags), \ 158 } 159 160 /* 161 * NOTE: When changing this, sync with xmit.c's 162 * b43_plcp_get_bitrate_idx_* functions! 163 */ 164 static struct ieee80211_rate __b43_ratetable[] = { 165 RATETAB_ENT(B43_CCK_RATE_1MB, 0), 166 RATETAB_ENT(B43_CCK_RATE_2MB, IEEE80211_RATE_SHORT_PREAMBLE), 167 RATETAB_ENT(B43_CCK_RATE_5MB, IEEE80211_RATE_SHORT_PREAMBLE), 168 RATETAB_ENT(B43_CCK_RATE_11MB, IEEE80211_RATE_SHORT_PREAMBLE), 169 RATETAB_ENT(B43_OFDM_RATE_6MB, 0), 170 RATETAB_ENT(B43_OFDM_RATE_9MB, 0), 171 RATETAB_ENT(B43_OFDM_RATE_12MB, 0), 172 RATETAB_ENT(B43_OFDM_RATE_18MB, 0), 173 RATETAB_ENT(B43_OFDM_RATE_24MB, 0), 174 RATETAB_ENT(B43_OFDM_RATE_36MB, 0), 175 RATETAB_ENT(B43_OFDM_RATE_48MB, 0), 176 RATETAB_ENT(B43_OFDM_RATE_54MB, 0), 177 }; 178 179 #define b43_a_ratetable (__b43_ratetable + 4) 180 #define b43_a_ratetable_size 8 181 #define b43_b_ratetable (__b43_ratetable + 0) 182 #define b43_b_ratetable_size 4 183 #define b43_g_ratetable (__b43_ratetable + 0) 184 #define b43_g_ratetable_size 12 185 186 #define CHAN2G(_channel, _freq, _flags) { \ 187 .band = NL80211_BAND_2GHZ, \ 188 .center_freq = (_freq), \ 189 .hw_value = (_channel), \ 190 .flags = (_flags), \ 191 .max_antenna_gain = 0, \ 192 .max_power = 30, \ 193 } 194 static struct ieee80211_channel b43_2ghz_chantable[] = { 195 CHAN2G(1, 2412, 0), 196 CHAN2G(2, 2417, 0), 197 CHAN2G(3, 2422, 0), 198 CHAN2G(4, 2427, 0), 199 CHAN2G(5, 2432, 0), 200 CHAN2G(6, 2437, 0), 201 CHAN2G(7, 2442, 0), 202 CHAN2G(8, 2447, 0), 203 CHAN2G(9, 2452, 0), 204 CHAN2G(10, 2457, 0), 205 CHAN2G(11, 2462, 0), 206 CHAN2G(12, 2467, 0), 207 CHAN2G(13, 2472, 0), 208 CHAN2G(14, 2484, 0), 209 }; 210 211 /* No support for the last 3 channels (12, 13, 14) */ 212 #define b43_2ghz_chantable_limited_size 11 213 #undef CHAN2G 214 215 #define CHAN4G(_channel, _flags) { \ 216 .band = NL80211_BAND_5GHZ, \ 217 .center_freq = 4000 + (5 * (_channel)), \ 218 .hw_value = (_channel), \ 219 .flags = (_flags), \ 220 .max_antenna_gain = 0, \ 221 .max_power = 30, \ 222 } 223 #define CHAN5G(_channel, _flags) { \ 224 .band = NL80211_BAND_5GHZ, \ 225 .center_freq = 5000 + (5 * (_channel)), \ 226 .hw_value = (_channel), \ 227 .flags = (_flags), \ 228 .max_antenna_gain = 0, \ 229 .max_power = 30, \ 230 } 231 static struct ieee80211_channel b43_5ghz_nphy_chantable[] = { 232 CHAN4G(184, 0), CHAN4G(186, 0), 233 CHAN4G(188, 0), CHAN4G(190, 0), 234 CHAN4G(192, 0), CHAN4G(194, 0), 235 CHAN4G(196, 0), CHAN4G(198, 0), 236 CHAN4G(200, 0), CHAN4G(202, 0), 237 CHAN4G(204, 0), CHAN4G(206, 0), 238 CHAN4G(208, 0), CHAN4G(210, 0), 239 CHAN4G(212, 0), CHAN4G(214, 0), 240 CHAN4G(216, 0), CHAN4G(218, 0), 241 CHAN4G(220, 0), CHAN4G(222, 0), 242 CHAN4G(224, 0), CHAN4G(226, 0), 243 CHAN4G(228, 0), 244 CHAN5G(32, 0), CHAN5G(34, 0), 245 CHAN5G(36, 0), CHAN5G(38, 0), 246 CHAN5G(40, 0), CHAN5G(42, 0), 247 CHAN5G(44, 0), CHAN5G(46, 0), 248 CHAN5G(48, 0), CHAN5G(50, 0), 249 CHAN5G(52, 0), CHAN5G(54, 0), 250 CHAN5G(56, 0), CHAN5G(58, 0), 251 CHAN5G(60, 0), CHAN5G(62, 0), 252 CHAN5G(64, 0), CHAN5G(66, 0), 253 CHAN5G(68, 0), CHAN5G(70, 0), 254 CHAN5G(72, 0), CHAN5G(74, 0), 255 CHAN5G(76, 0), CHAN5G(78, 0), 256 CHAN5G(80, 0), CHAN5G(82, 0), 257 CHAN5G(84, 0), CHAN5G(86, 0), 258 CHAN5G(88, 0), CHAN5G(90, 0), 259 CHAN5G(92, 0), CHAN5G(94, 0), 260 CHAN5G(96, 0), CHAN5G(98, 0), 261 CHAN5G(100, 0), CHAN5G(102, 0), 262 CHAN5G(104, 0), CHAN5G(106, 0), 263 CHAN5G(108, 0), CHAN5G(110, 0), 264 CHAN5G(112, 0), CHAN5G(114, 0), 265 CHAN5G(116, 0), CHAN5G(118, 0), 266 CHAN5G(120, 0), CHAN5G(122, 0), 267 CHAN5G(124, 0), CHAN5G(126, 0), 268 CHAN5G(128, 0), CHAN5G(130, 0), 269 CHAN5G(132, 0), CHAN5G(134, 0), 270 CHAN5G(136, 0), CHAN5G(138, 0), 271 CHAN5G(140, 0), CHAN5G(142, 0), 272 CHAN5G(144, 0), CHAN5G(145, 0), 273 CHAN5G(146, 0), CHAN5G(147, 0), 274 CHAN5G(148, 0), CHAN5G(149, 0), 275 CHAN5G(150, 0), CHAN5G(151, 0), 276 CHAN5G(152, 0), CHAN5G(153, 0), 277 CHAN5G(154, 0), CHAN5G(155, 0), 278 CHAN5G(156, 0), CHAN5G(157, 0), 279 CHAN5G(158, 0), CHAN5G(159, 0), 280 CHAN5G(160, 0), CHAN5G(161, 0), 281 CHAN5G(162, 0), CHAN5G(163, 0), 282 CHAN5G(164, 0), CHAN5G(165, 0), 283 CHAN5G(166, 0), CHAN5G(168, 0), 284 CHAN5G(170, 0), CHAN5G(172, 0), 285 CHAN5G(174, 0), CHAN5G(176, 0), 286 CHAN5G(178, 0), CHAN5G(180, 0), 287 CHAN5G(182, 0), 288 }; 289 290 static struct ieee80211_channel b43_5ghz_nphy_chantable_limited[] = { 291 CHAN5G(36, 0), CHAN5G(40, 0), 292 CHAN5G(44, 0), CHAN5G(48, 0), 293 CHAN5G(149, 0), CHAN5G(153, 0), 294 CHAN5G(157, 0), CHAN5G(161, 0), 295 CHAN5G(165, 0), 296 }; 297 298 static struct ieee80211_channel b43_5ghz_aphy_chantable[] = { 299 CHAN5G(34, 0), CHAN5G(36, 0), 300 CHAN5G(38, 0), CHAN5G(40, 0), 301 CHAN5G(42, 0), CHAN5G(44, 0), 302 CHAN5G(46, 0), CHAN5G(48, 0), 303 CHAN5G(52, 0), CHAN5G(56, 0), 304 CHAN5G(60, 0), CHAN5G(64, 0), 305 CHAN5G(100, 0), CHAN5G(104, 0), 306 CHAN5G(108, 0), CHAN5G(112, 0), 307 CHAN5G(116, 0), CHAN5G(120, 0), 308 CHAN5G(124, 0), CHAN5G(128, 0), 309 CHAN5G(132, 0), CHAN5G(136, 0), 310 CHAN5G(140, 0), CHAN5G(149, 0), 311 CHAN5G(153, 0), CHAN5G(157, 0), 312 CHAN5G(161, 0), CHAN5G(165, 0), 313 CHAN5G(184, 0), CHAN5G(188, 0), 314 CHAN5G(192, 0), CHAN5G(196, 0), 315 CHAN5G(200, 0), CHAN5G(204, 0), 316 CHAN5G(208, 0), CHAN5G(212, 0), 317 CHAN5G(216, 0), 318 }; 319 #undef CHAN4G 320 #undef CHAN5G 321 322 static struct ieee80211_supported_band b43_band_5GHz_nphy = { 323 .band = NL80211_BAND_5GHZ, 324 .channels = b43_5ghz_nphy_chantable, 325 .n_channels = ARRAY_SIZE(b43_5ghz_nphy_chantable), 326 .bitrates = b43_a_ratetable, 327 .n_bitrates = b43_a_ratetable_size, 328 }; 329 330 static struct ieee80211_supported_band b43_band_5GHz_nphy_limited = { 331 .band = NL80211_BAND_5GHZ, 332 .channels = b43_5ghz_nphy_chantable_limited, 333 .n_channels = ARRAY_SIZE(b43_5ghz_nphy_chantable_limited), 334 .bitrates = b43_a_ratetable, 335 .n_bitrates = b43_a_ratetable_size, 336 }; 337 338 static struct ieee80211_supported_band b43_band_5GHz_aphy = { 339 .band = NL80211_BAND_5GHZ, 340 .channels = b43_5ghz_aphy_chantable, 341 .n_channels = ARRAY_SIZE(b43_5ghz_aphy_chantable), 342 .bitrates = b43_a_ratetable, 343 .n_bitrates = b43_a_ratetable_size, 344 }; 345 346 static struct ieee80211_supported_band b43_band_2GHz = { 347 .band = NL80211_BAND_2GHZ, 348 .channels = b43_2ghz_chantable, 349 .n_channels = ARRAY_SIZE(b43_2ghz_chantable), 350 .bitrates = b43_g_ratetable, 351 .n_bitrates = b43_g_ratetable_size, 352 }; 353 354 static struct ieee80211_supported_band b43_band_2ghz_limited = { 355 .band = NL80211_BAND_2GHZ, 356 .channels = b43_2ghz_chantable, 357 .n_channels = b43_2ghz_chantable_limited_size, 358 .bitrates = b43_g_ratetable, 359 .n_bitrates = b43_g_ratetable_size, 360 }; 361 362 static void b43_wireless_core_exit(struct b43_wldev *dev); 363 static int b43_wireless_core_init(struct b43_wldev *dev); 364 static struct b43_wldev * b43_wireless_core_stop(struct b43_wldev *dev); 365 static int b43_wireless_core_start(struct b43_wldev *dev); 366 static void b43_op_bss_info_changed(struct ieee80211_hw *hw, 367 struct ieee80211_vif *vif, 368 struct ieee80211_bss_conf *conf, 369 u32 changed); 370 371 static int b43_ratelimit(struct b43_wl *wl) 372 { 373 if (!wl || !wl->current_dev) 374 return 1; 375 if (b43_status(wl->current_dev) < B43_STAT_STARTED) 376 return 1; 377 /* We are up and running. 378 * Ratelimit the messages to avoid DoS over the net. */ 379 return net_ratelimit(); 380 } 381 382 void b43info(struct b43_wl *wl, const char *fmt, ...) 383 { 384 struct va_format vaf; 385 va_list args; 386 387 if (b43_modparam_verbose < B43_VERBOSITY_INFO) 388 return; 389 if (!b43_ratelimit(wl)) 390 return; 391 392 va_start(args, fmt); 393 394 vaf.fmt = fmt; 395 vaf.va = &args; 396 397 printk(KERN_INFO "b43-%s: %pV", 398 (wl && wl->hw) ? wiphy_name(wl->hw->wiphy) : "wlan", &vaf); 399 400 va_end(args); 401 } 402 403 void b43err(struct b43_wl *wl, const char *fmt, ...) 404 { 405 struct va_format vaf; 406 va_list args; 407 408 if (b43_modparam_verbose < B43_VERBOSITY_ERROR) 409 return; 410 if (!b43_ratelimit(wl)) 411 return; 412 413 va_start(args, fmt); 414 415 vaf.fmt = fmt; 416 vaf.va = &args; 417 418 printk(KERN_ERR "b43-%s ERROR: %pV", 419 (wl && wl->hw) ? wiphy_name(wl->hw->wiphy) : "wlan", &vaf); 420 421 va_end(args); 422 } 423 424 void b43warn(struct b43_wl *wl, const char *fmt, ...) 425 { 426 struct va_format vaf; 427 va_list args; 428 429 if (b43_modparam_verbose < B43_VERBOSITY_WARN) 430 return; 431 if (!b43_ratelimit(wl)) 432 return; 433 434 va_start(args, fmt); 435 436 vaf.fmt = fmt; 437 vaf.va = &args; 438 439 printk(KERN_WARNING "b43-%s warning: %pV", 440 (wl && wl->hw) ? wiphy_name(wl->hw->wiphy) : "wlan", &vaf); 441 442 va_end(args); 443 } 444 445 void b43dbg(struct b43_wl *wl, const char *fmt, ...) 446 { 447 struct va_format vaf; 448 va_list args; 449 450 if (b43_modparam_verbose < B43_VERBOSITY_DEBUG) 451 return; 452 453 va_start(args, fmt); 454 455 vaf.fmt = fmt; 456 vaf.va = &args; 457 458 printk(KERN_DEBUG "b43-%s debug: %pV", 459 (wl && wl->hw) ? wiphy_name(wl->hw->wiphy) : "wlan", &vaf); 460 461 va_end(args); 462 } 463 464 static void b43_ram_write(struct b43_wldev *dev, u16 offset, u32 val) 465 { 466 u32 macctl; 467 468 B43_WARN_ON(offset % 4 != 0); 469 470 macctl = b43_read32(dev, B43_MMIO_MACCTL); 471 if (macctl & B43_MACCTL_BE) 472 val = swab32(val); 473 474 b43_write32(dev, B43_MMIO_RAM_CONTROL, offset); 475 b43_write32(dev, B43_MMIO_RAM_DATA, val); 476 } 477 478 static inline void b43_shm_control_word(struct b43_wldev *dev, 479 u16 routing, u16 offset) 480 { 481 u32 control; 482 483 /* "offset" is the WORD offset. */ 484 control = routing; 485 control <<= 16; 486 control |= offset; 487 b43_write32(dev, B43_MMIO_SHM_CONTROL, control); 488 } 489 490 u32 b43_shm_read32(struct b43_wldev *dev, u16 routing, u16 offset) 491 { 492 u32 ret; 493 494 if (routing == B43_SHM_SHARED) { 495 B43_WARN_ON(offset & 0x0001); 496 if (offset & 0x0003) { 497 /* Unaligned access */ 498 b43_shm_control_word(dev, routing, offset >> 2); 499 ret = b43_read16(dev, B43_MMIO_SHM_DATA_UNALIGNED); 500 b43_shm_control_word(dev, routing, (offset >> 2) + 1); 501 ret |= ((u32)b43_read16(dev, B43_MMIO_SHM_DATA)) << 16; 502 503 goto out; 504 } 505 offset >>= 2; 506 } 507 b43_shm_control_word(dev, routing, offset); 508 ret = b43_read32(dev, B43_MMIO_SHM_DATA); 509 out: 510 return ret; 511 } 512 513 u16 b43_shm_read16(struct b43_wldev *dev, u16 routing, u16 offset) 514 { 515 u16 ret; 516 517 if (routing == B43_SHM_SHARED) { 518 B43_WARN_ON(offset & 0x0001); 519 if (offset & 0x0003) { 520 /* Unaligned access */ 521 b43_shm_control_word(dev, routing, offset >> 2); 522 ret = b43_read16(dev, B43_MMIO_SHM_DATA_UNALIGNED); 523 524 goto out; 525 } 526 offset >>= 2; 527 } 528 b43_shm_control_word(dev, routing, offset); 529 ret = b43_read16(dev, B43_MMIO_SHM_DATA); 530 out: 531 return ret; 532 } 533 534 void b43_shm_write32(struct b43_wldev *dev, u16 routing, u16 offset, u32 value) 535 { 536 if (routing == B43_SHM_SHARED) { 537 B43_WARN_ON(offset & 0x0001); 538 if (offset & 0x0003) { 539 /* Unaligned access */ 540 b43_shm_control_word(dev, routing, offset >> 2); 541 b43_write16(dev, B43_MMIO_SHM_DATA_UNALIGNED, 542 value & 0xFFFF); 543 b43_shm_control_word(dev, routing, (offset >> 2) + 1); 544 b43_write16(dev, B43_MMIO_SHM_DATA, 545 (value >> 16) & 0xFFFF); 546 return; 547 } 548 offset >>= 2; 549 } 550 b43_shm_control_word(dev, routing, offset); 551 b43_write32(dev, B43_MMIO_SHM_DATA, value); 552 } 553 554 void b43_shm_write16(struct b43_wldev *dev, u16 routing, u16 offset, u16 value) 555 { 556 if (routing == B43_SHM_SHARED) { 557 B43_WARN_ON(offset & 0x0001); 558 if (offset & 0x0003) { 559 /* Unaligned access */ 560 b43_shm_control_word(dev, routing, offset >> 2); 561 b43_write16(dev, B43_MMIO_SHM_DATA_UNALIGNED, value); 562 return; 563 } 564 offset >>= 2; 565 } 566 b43_shm_control_word(dev, routing, offset); 567 b43_write16(dev, B43_MMIO_SHM_DATA, value); 568 } 569 570 /* Read HostFlags */ 571 u64 b43_hf_read(struct b43_wldev *dev) 572 { 573 u64 ret; 574 575 ret = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTF3); 576 ret <<= 16; 577 ret |= b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTF2); 578 ret <<= 16; 579 ret |= b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTF1); 580 581 return ret; 582 } 583 584 /* Write HostFlags */ 585 void b43_hf_write(struct b43_wldev *dev, u64 value) 586 { 587 u16 lo, mi, hi; 588 589 lo = (value & 0x00000000FFFFULL); 590 mi = (value & 0x0000FFFF0000ULL) >> 16; 591 hi = (value & 0xFFFF00000000ULL) >> 32; 592 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTF1, lo); 593 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTF2, mi); 594 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTF3, hi); 595 } 596 597 /* Read the firmware capabilities bitmask (Opensource firmware only) */ 598 static u16 b43_fwcapa_read(struct b43_wldev *dev) 599 { 600 B43_WARN_ON(!dev->fw.opensource); 601 return b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_FWCAPA); 602 } 603 604 void b43_tsf_read(struct b43_wldev *dev, u64 *tsf) 605 { 606 u32 low, high; 607 608 B43_WARN_ON(dev->dev->core_rev < 3); 609 610 /* The hardware guarantees us an atomic read, if we 611 * read the low register first. */ 612 low = b43_read32(dev, B43_MMIO_REV3PLUS_TSF_LOW); 613 high = b43_read32(dev, B43_MMIO_REV3PLUS_TSF_HIGH); 614 615 *tsf = high; 616 *tsf <<= 32; 617 *tsf |= low; 618 } 619 620 static void b43_time_lock(struct b43_wldev *dev) 621 { 622 b43_maskset32(dev, B43_MMIO_MACCTL, ~0, B43_MACCTL_TBTTHOLD); 623 /* Commit the write */ 624 b43_read32(dev, B43_MMIO_MACCTL); 625 } 626 627 static void b43_time_unlock(struct b43_wldev *dev) 628 { 629 b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_TBTTHOLD, 0); 630 /* Commit the write */ 631 b43_read32(dev, B43_MMIO_MACCTL); 632 } 633 634 static void b43_tsf_write_locked(struct b43_wldev *dev, u64 tsf) 635 { 636 u32 low, high; 637 638 B43_WARN_ON(dev->dev->core_rev < 3); 639 640 low = tsf; 641 high = (tsf >> 32); 642 /* The hardware guarantees us an atomic write, if we 643 * write the low register first. */ 644 b43_write32(dev, B43_MMIO_REV3PLUS_TSF_LOW, low); 645 b43_write32(dev, B43_MMIO_REV3PLUS_TSF_HIGH, high); 646 } 647 648 void b43_tsf_write(struct b43_wldev *dev, u64 tsf) 649 { 650 b43_time_lock(dev); 651 b43_tsf_write_locked(dev, tsf); 652 b43_time_unlock(dev); 653 } 654 655 static 656 void b43_macfilter_set(struct b43_wldev *dev, u16 offset, const u8 *mac) 657 { 658 static const u8 zero_addr[ETH_ALEN] = { 0 }; 659 u16 data; 660 661 if (!mac) 662 mac = zero_addr; 663 664 offset |= 0x0020; 665 b43_write16(dev, B43_MMIO_MACFILTER_CONTROL, offset); 666 667 data = mac[0]; 668 data |= mac[1] << 8; 669 b43_write16(dev, B43_MMIO_MACFILTER_DATA, data); 670 data = mac[2]; 671 data |= mac[3] << 8; 672 b43_write16(dev, B43_MMIO_MACFILTER_DATA, data); 673 data = mac[4]; 674 data |= mac[5] << 8; 675 b43_write16(dev, B43_MMIO_MACFILTER_DATA, data); 676 } 677 678 static void b43_write_mac_bssid_templates(struct b43_wldev *dev) 679 { 680 const u8 *mac; 681 const u8 *bssid; 682 u8 mac_bssid[ETH_ALEN * 2]; 683 int i; 684 u32 tmp; 685 686 bssid = dev->wl->bssid; 687 mac = dev->wl->mac_addr; 688 689 b43_macfilter_set(dev, B43_MACFILTER_BSSID, bssid); 690 691 memcpy(mac_bssid, mac, ETH_ALEN); 692 memcpy(mac_bssid + ETH_ALEN, bssid, ETH_ALEN); 693 694 /* Write our MAC address and BSSID to template ram */ 695 for (i = 0; i < ARRAY_SIZE(mac_bssid); i += sizeof(u32)) { 696 tmp = (u32) (mac_bssid[i + 0]); 697 tmp |= (u32) (mac_bssid[i + 1]) << 8; 698 tmp |= (u32) (mac_bssid[i + 2]) << 16; 699 tmp |= (u32) (mac_bssid[i + 3]) << 24; 700 b43_ram_write(dev, 0x20 + i, tmp); 701 } 702 } 703 704 static void b43_upload_card_macaddress(struct b43_wldev *dev) 705 { 706 b43_write_mac_bssid_templates(dev); 707 b43_macfilter_set(dev, B43_MACFILTER_SELF, dev->wl->mac_addr); 708 } 709 710 static void b43_set_slot_time(struct b43_wldev *dev, u16 slot_time) 711 { 712 /* slot_time is in usec. */ 713 /* This test used to exit for all but a G PHY. */ 714 if (b43_current_band(dev->wl) == NL80211_BAND_5GHZ) 715 return; 716 b43_write16(dev, B43_MMIO_IFSSLOT, 510 + slot_time); 717 /* Shared memory location 0x0010 is the slot time and should be 718 * set to slot_time; however, this register is initially 0 and changing 719 * the value adversely affects the transmit rate for BCM4311 720 * devices. Until this behavior is unterstood, delete this step 721 * 722 * b43_shm_write16(dev, B43_SHM_SHARED, 0x0010, slot_time); 723 */ 724 } 725 726 static void b43_short_slot_timing_enable(struct b43_wldev *dev) 727 { 728 b43_set_slot_time(dev, 9); 729 } 730 731 static void b43_short_slot_timing_disable(struct b43_wldev *dev) 732 { 733 b43_set_slot_time(dev, 20); 734 } 735 736 /* DummyTransmission function, as documented on 737 * http://bcm-v4.sipsolutions.net/802.11/DummyTransmission 738 */ 739 void b43_dummy_transmission(struct b43_wldev *dev, bool ofdm, bool pa_on) 740 { 741 struct b43_phy *phy = &dev->phy; 742 unsigned int i, max_loop; 743 u16 value; 744 u32 buffer[5] = { 745 0x00000000, 746 0x00D40000, 747 0x00000000, 748 0x01000000, 749 0x00000000, 750 }; 751 752 if (ofdm) { 753 max_loop = 0x1E; 754 buffer[0] = 0x000201CC; 755 } else { 756 max_loop = 0xFA; 757 buffer[0] = 0x000B846E; 758 } 759 760 for (i = 0; i < 5; i++) 761 b43_ram_write(dev, i * 4, buffer[i]); 762 763 b43_write16(dev, B43_MMIO_XMTSEL, 0x0000); 764 765 if (dev->dev->core_rev < 11) 766 b43_write16(dev, B43_MMIO_WEPCTL, 0x0000); 767 else 768 b43_write16(dev, B43_MMIO_WEPCTL, 0x0100); 769 770 value = (ofdm ? 0x41 : 0x40); 771 b43_write16(dev, B43_MMIO_TXE0_PHYCTL, value); 772 if (phy->type == B43_PHYTYPE_N || phy->type == B43_PHYTYPE_LP || 773 phy->type == B43_PHYTYPE_LCN) 774 b43_write16(dev, B43_MMIO_TXE0_PHYCTL1, 0x1A02); 775 776 b43_write16(dev, B43_MMIO_TXE0_WM_0, 0x0000); 777 b43_write16(dev, B43_MMIO_TXE0_WM_1, 0x0000); 778 779 b43_write16(dev, B43_MMIO_XMTTPLATETXPTR, 0x0000); 780 b43_write16(dev, B43_MMIO_XMTTXCNT, 0x0014); 781 b43_write16(dev, B43_MMIO_XMTSEL, 0x0826); 782 b43_write16(dev, B43_MMIO_TXE0_CTL, 0x0000); 783 784 if (!pa_on && phy->type == B43_PHYTYPE_N) 785 ; /*b43_nphy_pa_override(dev, false) */ 786 787 switch (phy->type) { 788 case B43_PHYTYPE_N: 789 case B43_PHYTYPE_LCN: 790 b43_write16(dev, B43_MMIO_TXE0_AUX, 0x00D0); 791 break; 792 case B43_PHYTYPE_LP: 793 b43_write16(dev, B43_MMIO_TXE0_AUX, 0x0050); 794 break; 795 default: 796 b43_write16(dev, B43_MMIO_TXE0_AUX, 0x0030); 797 } 798 b43_read16(dev, B43_MMIO_TXE0_AUX); 799 800 if (phy->radio_ver == 0x2050 && phy->radio_rev <= 0x5) 801 b43_radio_write16(dev, 0x0051, 0x0017); 802 for (i = 0x00; i < max_loop; i++) { 803 value = b43_read16(dev, B43_MMIO_TXE0_STATUS); 804 if (value & 0x0080) 805 break; 806 udelay(10); 807 } 808 for (i = 0x00; i < 0x0A; i++) { 809 value = b43_read16(dev, B43_MMIO_TXE0_STATUS); 810 if (value & 0x0400) 811 break; 812 udelay(10); 813 } 814 for (i = 0x00; i < 0x19; i++) { 815 value = b43_read16(dev, B43_MMIO_IFSSTAT); 816 if (!(value & 0x0100)) 817 break; 818 udelay(10); 819 } 820 if (phy->radio_ver == 0x2050 && phy->radio_rev <= 0x5) 821 b43_radio_write16(dev, 0x0051, 0x0037); 822 } 823 824 static void key_write(struct b43_wldev *dev, 825 u8 index, u8 algorithm, const u8 *key) 826 { 827 unsigned int i; 828 u32 offset; 829 u16 value; 830 u16 kidx; 831 832 /* Key index/algo block */ 833 kidx = b43_kidx_to_fw(dev, index); 834 value = ((kidx << 4) | algorithm); 835 b43_shm_write16(dev, B43_SHM_SHARED, 836 B43_SHM_SH_KEYIDXBLOCK + (kidx * 2), value); 837 838 /* Write the key to the Key Table Pointer offset */ 839 offset = dev->ktp + (index * B43_SEC_KEYSIZE); 840 for (i = 0; i < B43_SEC_KEYSIZE; i += 2) { 841 value = key[i]; 842 value |= (u16) (key[i + 1]) << 8; 843 b43_shm_write16(dev, B43_SHM_SHARED, offset + i, value); 844 } 845 } 846 847 static void keymac_write(struct b43_wldev *dev, u8 index, const u8 *addr) 848 { 849 u32 addrtmp[2] = { 0, 0, }; 850 u8 pairwise_keys_start = B43_NR_GROUP_KEYS * 2; 851 852 if (b43_new_kidx_api(dev)) 853 pairwise_keys_start = B43_NR_GROUP_KEYS; 854 855 B43_WARN_ON(index < pairwise_keys_start); 856 /* We have four default TX keys and possibly four default RX keys. 857 * Physical mac 0 is mapped to physical key 4 or 8, depending 858 * on the firmware version. 859 * So we must adjust the index here. 860 */ 861 index -= pairwise_keys_start; 862 B43_WARN_ON(index >= B43_NR_PAIRWISE_KEYS); 863 864 if (addr) { 865 addrtmp[0] = addr[0]; 866 addrtmp[0] |= ((u32) (addr[1]) << 8); 867 addrtmp[0] |= ((u32) (addr[2]) << 16); 868 addrtmp[0] |= ((u32) (addr[3]) << 24); 869 addrtmp[1] = addr[4]; 870 addrtmp[1] |= ((u32) (addr[5]) << 8); 871 } 872 873 /* Receive match transmitter address (RCMTA) mechanism */ 874 b43_shm_write32(dev, B43_SHM_RCMTA, 875 (index * 2) + 0, addrtmp[0]); 876 b43_shm_write16(dev, B43_SHM_RCMTA, 877 (index * 2) + 1, addrtmp[1]); 878 } 879 880 /* The ucode will use phase1 key with TEK key to decrypt rx packets. 881 * When a packet is received, the iv32 is checked. 882 * - if it doesn't the packet is returned without modification (and software 883 * decryption can be done). That's what happen when iv16 wrap. 884 * - if it does, the rc4 key is computed, and decryption is tried. 885 * Either it will success and B43_RX_MAC_DEC is returned, 886 * either it fails and B43_RX_MAC_DEC|B43_RX_MAC_DECERR is returned 887 * and the packet is not usable (it got modified by the ucode). 888 * So in order to never have B43_RX_MAC_DECERR, we should provide 889 * a iv32 and phase1key that match. Because we drop packets in case of 890 * B43_RX_MAC_DECERR, if we have a correct iv32 but a wrong phase1key, all 891 * packets will be lost without higher layer knowing (ie no resync possible 892 * until next wrap). 893 * 894 * NOTE : this should support 50 key like RCMTA because 895 * (B43_SHM_SH_KEYIDXBLOCK - B43_SHM_SH_TKIPTSCTTAK)/14 = 50 896 */ 897 static void rx_tkip_phase1_write(struct b43_wldev *dev, u8 index, u32 iv32, 898 u16 *phase1key) 899 { 900 unsigned int i; 901 u32 offset; 902 u8 pairwise_keys_start = B43_NR_GROUP_KEYS * 2; 903 904 if (!modparam_hwtkip) 905 return; 906 907 if (b43_new_kidx_api(dev)) 908 pairwise_keys_start = B43_NR_GROUP_KEYS; 909 910 B43_WARN_ON(index < pairwise_keys_start); 911 /* We have four default TX keys and possibly four default RX keys. 912 * Physical mac 0 is mapped to physical key 4 or 8, depending 913 * on the firmware version. 914 * So we must adjust the index here. 915 */ 916 index -= pairwise_keys_start; 917 B43_WARN_ON(index >= B43_NR_PAIRWISE_KEYS); 918 919 if (b43_debug(dev, B43_DBG_KEYS)) { 920 b43dbg(dev->wl, "rx_tkip_phase1_write : idx 0x%x, iv32 0x%x\n", 921 index, iv32); 922 } 923 /* Write the key to the RX tkip shared mem */ 924 offset = B43_SHM_SH_TKIPTSCTTAK + index * (10 + 4); 925 for (i = 0; i < 10; i += 2) { 926 b43_shm_write16(dev, B43_SHM_SHARED, offset + i, 927 phase1key ? phase1key[i / 2] : 0); 928 } 929 b43_shm_write16(dev, B43_SHM_SHARED, offset + i, iv32); 930 b43_shm_write16(dev, B43_SHM_SHARED, offset + i + 2, iv32 >> 16); 931 } 932 933 static void b43_op_update_tkip_key(struct ieee80211_hw *hw, 934 struct ieee80211_vif *vif, 935 struct ieee80211_key_conf *keyconf, 936 struct ieee80211_sta *sta, 937 u32 iv32, u16 *phase1key) 938 { 939 struct b43_wl *wl = hw_to_b43_wl(hw); 940 struct b43_wldev *dev; 941 int index = keyconf->hw_key_idx; 942 943 if (B43_WARN_ON(!modparam_hwtkip)) 944 return; 945 946 /* This is only called from the RX path through mac80211, where 947 * our mutex is already locked. */ 948 B43_WARN_ON(!mutex_is_locked(&wl->mutex)); 949 dev = wl->current_dev; 950 B43_WARN_ON(!dev || b43_status(dev) < B43_STAT_INITIALIZED); 951 952 keymac_write(dev, index, NULL); /* First zero out mac to avoid race */ 953 954 rx_tkip_phase1_write(dev, index, iv32, phase1key); 955 /* only pairwise TKIP keys are supported right now */ 956 if (WARN_ON(!sta)) 957 return; 958 keymac_write(dev, index, sta->addr); 959 } 960 961 static void do_key_write(struct b43_wldev *dev, 962 u8 index, u8 algorithm, 963 const u8 *key, size_t key_len, const u8 *mac_addr) 964 { 965 u8 buf[B43_SEC_KEYSIZE] = { 0, }; 966 u8 pairwise_keys_start = B43_NR_GROUP_KEYS * 2; 967 968 if (b43_new_kidx_api(dev)) 969 pairwise_keys_start = B43_NR_GROUP_KEYS; 970 971 B43_WARN_ON(index >= ARRAY_SIZE(dev->key)); 972 B43_WARN_ON(key_len > B43_SEC_KEYSIZE); 973 974 if (index >= pairwise_keys_start) 975 keymac_write(dev, index, NULL); /* First zero out mac. */ 976 if (algorithm == B43_SEC_ALGO_TKIP) { 977 /* 978 * We should provide an initial iv32, phase1key pair. 979 * We could start with iv32=0 and compute the corresponding 980 * phase1key, but this means calling ieee80211_get_tkip_key 981 * with a fake skb (or export other tkip function). 982 * Because we are lazy we hope iv32 won't start with 983 * 0xffffffff and let's b43_op_update_tkip_key provide a 984 * correct pair. 985 */ 986 rx_tkip_phase1_write(dev, index, 0xffffffff, (u16*)buf); 987 } else if (index >= pairwise_keys_start) /* clear it */ 988 rx_tkip_phase1_write(dev, index, 0, NULL); 989 if (key) 990 memcpy(buf, key, key_len); 991 key_write(dev, index, algorithm, buf); 992 if (index >= pairwise_keys_start) 993 keymac_write(dev, index, mac_addr); 994 995 dev->key[index].algorithm = algorithm; 996 } 997 998 static int b43_key_write(struct b43_wldev *dev, 999 int index, u8 algorithm, 1000 const u8 *key, size_t key_len, 1001 const u8 *mac_addr, 1002 struct ieee80211_key_conf *keyconf) 1003 { 1004 int i; 1005 int pairwise_keys_start; 1006 1007 /* For ALG_TKIP the key is encoded as a 256-bit (32 byte) data block: 1008 * - Temporal Encryption Key (128 bits) 1009 * - Temporal Authenticator Tx MIC Key (64 bits) 1010 * - Temporal Authenticator Rx MIC Key (64 bits) 1011 * 1012 * Hardware only store TEK 1013 */ 1014 if (algorithm == B43_SEC_ALGO_TKIP && key_len == 32) 1015 key_len = 16; 1016 if (key_len > B43_SEC_KEYSIZE) 1017 return -EINVAL; 1018 for (i = 0; i < ARRAY_SIZE(dev->key); i++) { 1019 /* Check that we don't already have this key. */ 1020 B43_WARN_ON(dev->key[i].keyconf == keyconf); 1021 } 1022 if (index < 0) { 1023 /* Pairwise key. Get an empty slot for the key. */ 1024 if (b43_new_kidx_api(dev)) 1025 pairwise_keys_start = B43_NR_GROUP_KEYS; 1026 else 1027 pairwise_keys_start = B43_NR_GROUP_KEYS * 2; 1028 for (i = pairwise_keys_start; 1029 i < pairwise_keys_start + B43_NR_PAIRWISE_KEYS; 1030 i++) { 1031 B43_WARN_ON(i >= ARRAY_SIZE(dev->key)); 1032 if (!dev->key[i].keyconf) { 1033 /* found empty */ 1034 index = i; 1035 break; 1036 } 1037 } 1038 if (index < 0) { 1039 b43warn(dev->wl, "Out of hardware key memory\n"); 1040 return -ENOSPC; 1041 } 1042 } else 1043 B43_WARN_ON(index > 3); 1044 1045 do_key_write(dev, index, algorithm, key, key_len, mac_addr); 1046 if ((index <= 3) && !b43_new_kidx_api(dev)) { 1047 /* Default RX key */ 1048 B43_WARN_ON(mac_addr); 1049 do_key_write(dev, index + 4, algorithm, key, key_len, NULL); 1050 } 1051 keyconf->hw_key_idx = index; 1052 dev->key[index].keyconf = keyconf; 1053 1054 return 0; 1055 } 1056 1057 static int b43_key_clear(struct b43_wldev *dev, int index) 1058 { 1059 if (B43_WARN_ON((index < 0) || (index >= ARRAY_SIZE(dev->key)))) 1060 return -EINVAL; 1061 do_key_write(dev, index, B43_SEC_ALGO_NONE, 1062 NULL, B43_SEC_KEYSIZE, NULL); 1063 if ((index <= 3) && !b43_new_kidx_api(dev)) { 1064 do_key_write(dev, index + 4, B43_SEC_ALGO_NONE, 1065 NULL, B43_SEC_KEYSIZE, NULL); 1066 } 1067 dev->key[index].keyconf = NULL; 1068 1069 return 0; 1070 } 1071 1072 static void b43_clear_keys(struct b43_wldev *dev) 1073 { 1074 int i, count; 1075 1076 if (b43_new_kidx_api(dev)) 1077 count = B43_NR_GROUP_KEYS + B43_NR_PAIRWISE_KEYS; 1078 else 1079 count = B43_NR_GROUP_KEYS * 2 + B43_NR_PAIRWISE_KEYS; 1080 for (i = 0; i < count; i++) 1081 b43_key_clear(dev, i); 1082 } 1083 1084 static void b43_dump_keymemory(struct b43_wldev *dev) 1085 { 1086 unsigned int i, index, count, offset, pairwise_keys_start; 1087 u8 mac[ETH_ALEN]; 1088 u16 algo; 1089 u32 rcmta0; 1090 u16 rcmta1; 1091 u64 hf; 1092 struct b43_key *key; 1093 1094 if (!b43_debug(dev, B43_DBG_KEYS)) 1095 return; 1096 1097 hf = b43_hf_read(dev); 1098 b43dbg(dev->wl, "Hardware key memory dump: USEDEFKEYS=%u\n", 1099 !!(hf & B43_HF_USEDEFKEYS)); 1100 if (b43_new_kidx_api(dev)) { 1101 pairwise_keys_start = B43_NR_GROUP_KEYS; 1102 count = B43_NR_GROUP_KEYS + B43_NR_PAIRWISE_KEYS; 1103 } else { 1104 pairwise_keys_start = B43_NR_GROUP_KEYS * 2; 1105 count = B43_NR_GROUP_KEYS * 2 + B43_NR_PAIRWISE_KEYS; 1106 } 1107 for (index = 0; index < count; index++) { 1108 key = &(dev->key[index]); 1109 printk(KERN_DEBUG "Key slot %02u: %s", 1110 index, (key->keyconf == NULL) ? " " : "*"); 1111 offset = dev->ktp + (index * B43_SEC_KEYSIZE); 1112 for (i = 0; i < B43_SEC_KEYSIZE; i += 2) { 1113 u16 tmp = b43_shm_read16(dev, B43_SHM_SHARED, offset + i); 1114 printk("%02X%02X", (tmp & 0xFF), ((tmp >> 8) & 0xFF)); 1115 } 1116 1117 algo = b43_shm_read16(dev, B43_SHM_SHARED, 1118 B43_SHM_SH_KEYIDXBLOCK + (index * 2)); 1119 printk(" Algo: %04X/%02X", algo, key->algorithm); 1120 1121 if (index >= pairwise_keys_start) { 1122 if (key->algorithm == B43_SEC_ALGO_TKIP) { 1123 printk(" TKIP: "); 1124 offset = B43_SHM_SH_TKIPTSCTTAK + (index - 4) * (10 + 4); 1125 for (i = 0; i < 14; i += 2) { 1126 u16 tmp = b43_shm_read16(dev, B43_SHM_SHARED, offset + i); 1127 printk("%02X%02X", (tmp & 0xFF), ((tmp >> 8) & 0xFF)); 1128 } 1129 } 1130 rcmta0 = b43_shm_read32(dev, B43_SHM_RCMTA, 1131 ((index - pairwise_keys_start) * 2) + 0); 1132 rcmta1 = b43_shm_read16(dev, B43_SHM_RCMTA, 1133 ((index - pairwise_keys_start) * 2) + 1); 1134 *((__le32 *)(&mac[0])) = cpu_to_le32(rcmta0); 1135 *((__le16 *)(&mac[4])) = cpu_to_le16(rcmta1); 1136 printk(" MAC: %pM", mac); 1137 } else 1138 printk(" DEFAULT KEY"); 1139 printk("\n"); 1140 } 1141 } 1142 1143 void b43_power_saving_ctl_bits(struct b43_wldev *dev, unsigned int ps_flags) 1144 { 1145 u32 macctl; 1146 u16 ucstat; 1147 bool hwps; 1148 bool awake; 1149 int i; 1150 1151 B43_WARN_ON((ps_flags & B43_PS_ENABLED) && 1152 (ps_flags & B43_PS_DISABLED)); 1153 B43_WARN_ON((ps_flags & B43_PS_AWAKE) && (ps_flags & B43_PS_ASLEEP)); 1154 1155 if (ps_flags & B43_PS_ENABLED) { 1156 hwps = true; 1157 } else if (ps_flags & B43_PS_DISABLED) { 1158 hwps = false; 1159 } else { 1160 //TODO: If powersave is not off and FIXME is not set and we are not in adhoc 1161 // and thus is not an AP and we are associated, set bit 25 1162 } 1163 if (ps_flags & B43_PS_AWAKE) { 1164 awake = true; 1165 } else if (ps_flags & B43_PS_ASLEEP) { 1166 awake = false; 1167 } else { 1168 //TODO: If the device is awake or this is an AP, or we are scanning, or FIXME, 1169 // or we are associated, or FIXME, or the latest PS-Poll packet sent was 1170 // successful, set bit26 1171 } 1172 1173 /* FIXME: For now we force awake-on and hwps-off */ 1174 hwps = false; 1175 awake = true; 1176 1177 macctl = b43_read32(dev, B43_MMIO_MACCTL); 1178 if (hwps) 1179 macctl |= B43_MACCTL_HWPS; 1180 else 1181 macctl &= ~B43_MACCTL_HWPS; 1182 if (awake) 1183 macctl |= B43_MACCTL_AWAKE; 1184 else 1185 macctl &= ~B43_MACCTL_AWAKE; 1186 b43_write32(dev, B43_MMIO_MACCTL, macctl); 1187 /* Commit write */ 1188 b43_read32(dev, B43_MMIO_MACCTL); 1189 if (awake && dev->dev->core_rev >= 5) { 1190 /* Wait for the microcode to wake up. */ 1191 for (i = 0; i < 100; i++) { 1192 ucstat = b43_shm_read16(dev, B43_SHM_SHARED, 1193 B43_SHM_SH_UCODESTAT); 1194 if (ucstat != B43_SHM_SH_UCODESTAT_SLEEP) 1195 break; 1196 udelay(10); 1197 } 1198 } 1199 } 1200 1201 /* http://bcm-v4.sipsolutions.net/802.11/PHY/BmacCorePllReset */ 1202 void b43_wireless_core_phy_pll_reset(struct b43_wldev *dev) 1203 { 1204 struct bcma_drv_cc *bcma_cc __maybe_unused; 1205 struct ssb_chipcommon *ssb_cc __maybe_unused; 1206 1207 switch (dev->dev->bus_type) { 1208 #ifdef CONFIG_B43_BCMA 1209 case B43_BUS_BCMA: 1210 bcma_cc = &dev->dev->bdev->bus->drv_cc; 1211 1212 bcma_cc_write32(bcma_cc, BCMA_CC_PMU_CHIPCTL_ADDR, 0); 1213 bcma_cc_mask32(bcma_cc, BCMA_CC_PMU_CHIPCTL_DATA, ~0x4); 1214 bcma_cc_set32(bcma_cc, BCMA_CC_PMU_CHIPCTL_DATA, 0x4); 1215 bcma_cc_mask32(bcma_cc, BCMA_CC_PMU_CHIPCTL_DATA, ~0x4); 1216 break; 1217 #endif 1218 #ifdef CONFIG_B43_SSB 1219 case B43_BUS_SSB: 1220 ssb_cc = &dev->dev->sdev->bus->chipco; 1221 1222 chipco_write32(ssb_cc, SSB_CHIPCO_CHIPCTL_ADDR, 0); 1223 chipco_mask32(ssb_cc, SSB_CHIPCO_CHIPCTL_DATA, ~0x4); 1224 chipco_set32(ssb_cc, SSB_CHIPCO_CHIPCTL_DATA, 0x4); 1225 chipco_mask32(ssb_cc, SSB_CHIPCO_CHIPCTL_DATA, ~0x4); 1226 break; 1227 #endif 1228 } 1229 } 1230 1231 #ifdef CONFIG_B43_BCMA 1232 static void b43_bcma_phy_reset(struct b43_wldev *dev) 1233 { 1234 u32 flags; 1235 1236 /* Put PHY into reset */ 1237 flags = bcma_aread32(dev->dev->bdev, BCMA_IOCTL); 1238 flags |= B43_BCMA_IOCTL_PHY_RESET; 1239 flags |= B43_BCMA_IOCTL_PHY_BW_20MHZ; /* Make 20 MHz def */ 1240 bcma_awrite32(dev->dev->bdev, BCMA_IOCTL, flags); 1241 udelay(2); 1242 1243 b43_phy_take_out_of_reset(dev); 1244 } 1245 1246 static void b43_bcma_wireless_core_reset(struct b43_wldev *dev, bool gmode) 1247 { 1248 u32 req = B43_BCMA_CLKCTLST_80211_PLL_REQ | 1249 B43_BCMA_CLKCTLST_PHY_PLL_REQ; 1250 u32 status = B43_BCMA_CLKCTLST_80211_PLL_ST | 1251 B43_BCMA_CLKCTLST_PHY_PLL_ST; 1252 u32 flags; 1253 1254 flags = B43_BCMA_IOCTL_PHY_CLKEN; 1255 if (gmode) 1256 flags |= B43_BCMA_IOCTL_GMODE; 1257 b43_device_enable(dev, flags); 1258 1259 if (dev->phy.type == B43_PHYTYPE_AC) { 1260 u16 tmp; 1261 1262 tmp = bcma_aread32(dev->dev->bdev, BCMA_IOCTL); 1263 tmp &= ~B43_BCMA_IOCTL_DAC; 1264 tmp |= 0x100; 1265 bcma_awrite32(dev->dev->bdev, BCMA_IOCTL, tmp); 1266 1267 tmp = bcma_aread32(dev->dev->bdev, BCMA_IOCTL); 1268 tmp &= ~B43_BCMA_IOCTL_PHY_CLKEN; 1269 bcma_awrite32(dev->dev->bdev, BCMA_IOCTL, tmp); 1270 1271 tmp = bcma_aread32(dev->dev->bdev, BCMA_IOCTL); 1272 tmp |= B43_BCMA_IOCTL_PHY_CLKEN; 1273 bcma_awrite32(dev->dev->bdev, BCMA_IOCTL, tmp); 1274 } 1275 1276 bcma_core_set_clockmode(dev->dev->bdev, BCMA_CLKMODE_FAST); 1277 b43_bcma_phy_reset(dev); 1278 bcma_core_pll_ctl(dev->dev->bdev, req, status, true); 1279 } 1280 #endif 1281 1282 #ifdef CONFIG_B43_SSB 1283 static void b43_ssb_wireless_core_reset(struct b43_wldev *dev, bool gmode) 1284 { 1285 u32 flags = 0; 1286 1287 if (gmode) 1288 flags |= B43_TMSLOW_GMODE; 1289 flags |= B43_TMSLOW_PHYCLKEN; 1290 flags |= B43_TMSLOW_PHYRESET; 1291 if (dev->phy.type == B43_PHYTYPE_N) 1292 flags |= B43_TMSLOW_PHY_BANDWIDTH_20MHZ; /* Make 20 MHz def */ 1293 b43_device_enable(dev, flags); 1294 msleep(2); /* Wait for the PLL to turn on. */ 1295 1296 b43_phy_take_out_of_reset(dev); 1297 } 1298 #endif 1299 1300 void b43_wireless_core_reset(struct b43_wldev *dev, bool gmode) 1301 { 1302 u32 macctl; 1303 1304 switch (dev->dev->bus_type) { 1305 #ifdef CONFIG_B43_BCMA 1306 case B43_BUS_BCMA: 1307 b43_bcma_wireless_core_reset(dev, gmode); 1308 break; 1309 #endif 1310 #ifdef CONFIG_B43_SSB 1311 case B43_BUS_SSB: 1312 b43_ssb_wireless_core_reset(dev, gmode); 1313 break; 1314 #endif 1315 } 1316 1317 /* Turn Analog ON, but only if we already know the PHY-type. 1318 * This protects against very early setup where we don't know the 1319 * PHY-type, yet. wireless_core_reset will be called once again later, 1320 * when we know the PHY-type. */ 1321 if (dev->phy.ops) 1322 dev->phy.ops->switch_analog(dev, 1); 1323 1324 macctl = b43_read32(dev, B43_MMIO_MACCTL); 1325 macctl &= ~B43_MACCTL_GMODE; 1326 if (gmode) 1327 macctl |= B43_MACCTL_GMODE; 1328 macctl |= B43_MACCTL_IHR_ENABLED; 1329 b43_write32(dev, B43_MMIO_MACCTL, macctl); 1330 } 1331 1332 static void handle_irq_transmit_status(struct b43_wldev *dev) 1333 { 1334 u32 v0, v1; 1335 u16 tmp; 1336 struct b43_txstatus stat; 1337 1338 while (1) { 1339 v0 = b43_read32(dev, B43_MMIO_XMITSTAT_0); 1340 if (!(v0 & 0x00000001)) 1341 break; 1342 v1 = b43_read32(dev, B43_MMIO_XMITSTAT_1); 1343 1344 stat.cookie = (v0 >> 16); 1345 stat.seq = (v1 & 0x0000FFFF); 1346 stat.phy_stat = ((v1 & 0x00FF0000) >> 16); 1347 tmp = (v0 & 0x0000FFFF); 1348 stat.frame_count = ((tmp & 0xF000) >> 12); 1349 stat.rts_count = ((tmp & 0x0F00) >> 8); 1350 stat.supp_reason = ((tmp & 0x001C) >> 2); 1351 stat.pm_indicated = !!(tmp & 0x0080); 1352 stat.intermediate = !!(tmp & 0x0040); 1353 stat.for_ampdu = !!(tmp & 0x0020); 1354 stat.acked = !!(tmp & 0x0002); 1355 1356 b43_handle_txstatus(dev, &stat); 1357 } 1358 } 1359 1360 static void drain_txstatus_queue(struct b43_wldev *dev) 1361 { 1362 u32 dummy; 1363 1364 if (dev->dev->core_rev < 5) 1365 return; 1366 /* Read all entries from the microcode TXstatus FIFO 1367 * and throw them away. 1368 */ 1369 while (1) { 1370 dummy = b43_read32(dev, B43_MMIO_XMITSTAT_0); 1371 if (!(dummy & 0x00000001)) 1372 break; 1373 dummy = b43_read32(dev, B43_MMIO_XMITSTAT_1); 1374 } 1375 } 1376 1377 static u32 b43_jssi_read(struct b43_wldev *dev) 1378 { 1379 u32 val = 0; 1380 1381 val = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_JSSI1); 1382 val <<= 16; 1383 val |= b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_JSSI0); 1384 1385 return val; 1386 } 1387 1388 static void b43_jssi_write(struct b43_wldev *dev, u32 jssi) 1389 { 1390 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_JSSI0, 1391 (jssi & 0x0000FFFF)); 1392 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_JSSI1, 1393 (jssi & 0xFFFF0000) >> 16); 1394 } 1395 1396 static void b43_generate_noise_sample(struct b43_wldev *dev) 1397 { 1398 b43_jssi_write(dev, 0x7F7F7F7F); 1399 b43_write32(dev, B43_MMIO_MACCMD, 1400 b43_read32(dev, B43_MMIO_MACCMD) | B43_MACCMD_BGNOISE); 1401 } 1402 1403 static void b43_calculate_link_quality(struct b43_wldev *dev) 1404 { 1405 /* Top half of Link Quality calculation. */ 1406 1407 if (dev->phy.type != B43_PHYTYPE_G) 1408 return; 1409 if (dev->noisecalc.calculation_running) 1410 return; 1411 dev->noisecalc.calculation_running = true; 1412 dev->noisecalc.nr_samples = 0; 1413 1414 b43_generate_noise_sample(dev); 1415 } 1416 1417 static void handle_irq_noise(struct b43_wldev *dev) 1418 { 1419 struct b43_phy_g *phy = dev->phy.g; 1420 u16 tmp; 1421 u8 noise[4]; 1422 u8 i, j; 1423 s32 average; 1424 1425 /* Bottom half of Link Quality calculation. */ 1426 1427 if (dev->phy.type != B43_PHYTYPE_G) 1428 return; 1429 1430 /* Possible race condition: It might be possible that the user 1431 * changed to a different channel in the meantime since we 1432 * started the calculation. We ignore that fact, since it's 1433 * not really that much of a problem. The background noise is 1434 * an estimation only anyway. Slightly wrong results will get damped 1435 * by the averaging of the 8 sample rounds. Additionally the 1436 * value is shortlived. So it will be replaced by the next noise 1437 * calculation round soon. */ 1438 1439 B43_WARN_ON(!dev->noisecalc.calculation_running); 1440 *((__le32 *)noise) = cpu_to_le32(b43_jssi_read(dev)); 1441 if (noise[0] == 0x7F || noise[1] == 0x7F || 1442 noise[2] == 0x7F || noise[3] == 0x7F) 1443 goto generate_new; 1444 1445 /* Get the noise samples. */ 1446 B43_WARN_ON(dev->noisecalc.nr_samples >= 8); 1447 i = dev->noisecalc.nr_samples; 1448 noise[0] = clamp_val(noise[0], 0, ARRAY_SIZE(phy->nrssi_lt) - 1); 1449 noise[1] = clamp_val(noise[1], 0, ARRAY_SIZE(phy->nrssi_lt) - 1); 1450 noise[2] = clamp_val(noise[2], 0, ARRAY_SIZE(phy->nrssi_lt) - 1); 1451 noise[3] = clamp_val(noise[3], 0, ARRAY_SIZE(phy->nrssi_lt) - 1); 1452 dev->noisecalc.samples[i][0] = phy->nrssi_lt[noise[0]]; 1453 dev->noisecalc.samples[i][1] = phy->nrssi_lt[noise[1]]; 1454 dev->noisecalc.samples[i][2] = phy->nrssi_lt[noise[2]]; 1455 dev->noisecalc.samples[i][3] = phy->nrssi_lt[noise[3]]; 1456 dev->noisecalc.nr_samples++; 1457 if (dev->noisecalc.nr_samples == 8) { 1458 /* Calculate the Link Quality by the noise samples. */ 1459 average = 0; 1460 for (i = 0; i < 8; i++) { 1461 for (j = 0; j < 4; j++) 1462 average += dev->noisecalc.samples[i][j]; 1463 } 1464 average /= (8 * 4); 1465 average *= 125; 1466 average += 64; 1467 average /= 128; 1468 tmp = b43_shm_read16(dev, B43_SHM_SHARED, 0x40C); 1469 tmp = (tmp / 128) & 0x1F; 1470 if (tmp >= 8) 1471 average += 2; 1472 else 1473 average -= 25; 1474 if (tmp == 8) 1475 average -= 72; 1476 else 1477 average -= 48; 1478 1479 dev->stats.link_noise = average; 1480 dev->noisecalc.calculation_running = false; 1481 return; 1482 } 1483 generate_new: 1484 b43_generate_noise_sample(dev); 1485 } 1486 1487 static void handle_irq_tbtt_indication(struct b43_wldev *dev) 1488 { 1489 if (b43_is_mode(dev->wl, NL80211_IFTYPE_AP)) { 1490 ///TODO: PS TBTT 1491 } else { 1492 if (1 /*FIXME: the last PSpoll frame was sent successfully */ ) 1493 b43_power_saving_ctl_bits(dev, 0); 1494 } 1495 if (b43_is_mode(dev->wl, NL80211_IFTYPE_ADHOC)) 1496 dev->dfq_valid = true; 1497 } 1498 1499 static void handle_irq_atim_end(struct b43_wldev *dev) 1500 { 1501 if (dev->dfq_valid) { 1502 b43_write32(dev, B43_MMIO_MACCMD, 1503 b43_read32(dev, B43_MMIO_MACCMD) 1504 | B43_MACCMD_DFQ_VALID); 1505 dev->dfq_valid = false; 1506 } 1507 } 1508 1509 static void handle_irq_pmq(struct b43_wldev *dev) 1510 { 1511 u32 tmp; 1512 1513 //TODO: AP mode. 1514 1515 while (1) { 1516 tmp = b43_read32(dev, B43_MMIO_PS_STATUS); 1517 if (!(tmp & 0x00000008)) 1518 break; 1519 } 1520 /* 16bit write is odd, but correct. */ 1521 b43_write16(dev, B43_MMIO_PS_STATUS, 0x0002); 1522 } 1523 1524 static void b43_write_template_common(struct b43_wldev *dev, 1525 const u8 *data, u16 size, 1526 u16 ram_offset, 1527 u16 shm_size_offset, u8 rate) 1528 { 1529 u32 i, tmp; 1530 struct b43_plcp_hdr4 plcp; 1531 1532 plcp.data = 0; 1533 b43_generate_plcp_hdr(&plcp, size + FCS_LEN, rate); 1534 b43_ram_write(dev, ram_offset, le32_to_cpu(plcp.data)); 1535 ram_offset += sizeof(u32); 1536 /* The PLCP is 6 bytes long, but we only wrote 4 bytes, yet. 1537 * So leave the first two bytes of the next write blank. 1538 */ 1539 tmp = (u32) (data[0]) << 16; 1540 tmp |= (u32) (data[1]) << 24; 1541 b43_ram_write(dev, ram_offset, tmp); 1542 ram_offset += sizeof(u32); 1543 for (i = 2; i < size; i += sizeof(u32)) { 1544 tmp = (u32) (data[i + 0]); 1545 if (i + 1 < size) 1546 tmp |= (u32) (data[i + 1]) << 8; 1547 if (i + 2 < size) 1548 tmp |= (u32) (data[i + 2]) << 16; 1549 if (i + 3 < size) 1550 tmp |= (u32) (data[i + 3]) << 24; 1551 b43_ram_write(dev, ram_offset + i - 2, tmp); 1552 } 1553 b43_shm_write16(dev, B43_SHM_SHARED, shm_size_offset, 1554 size + sizeof(struct b43_plcp_hdr6)); 1555 } 1556 1557 /* Check if the use of the antenna that ieee80211 told us to 1558 * use is possible. This will fall back to DEFAULT. 1559 * "antenna_nr" is the antenna identifier we got from ieee80211. */ 1560 u8 b43_ieee80211_antenna_sanitize(struct b43_wldev *dev, 1561 u8 antenna_nr) 1562 { 1563 u8 antenna_mask; 1564 1565 if (antenna_nr == 0) { 1566 /* Zero means "use default antenna". That's always OK. */ 1567 return 0; 1568 } 1569 1570 /* Get the mask of available antennas. */ 1571 if (dev->phy.gmode) 1572 antenna_mask = dev->dev->bus_sprom->ant_available_bg; 1573 else 1574 antenna_mask = dev->dev->bus_sprom->ant_available_a; 1575 1576 if (!(antenna_mask & (1 << (antenna_nr - 1)))) { 1577 /* This antenna is not available. Fall back to default. */ 1578 return 0; 1579 } 1580 1581 return antenna_nr; 1582 } 1583 1584 /* Convert a b43 antenna number value to the PHY TX control value. */ 1585 static u16 b43_antenna_to_phyctl(int antenna) 1586 { 1587 switch (antenna) { 1588 case B43_ANTENNA0: 1589 return B43_TXH_PHY_ANT0; 1590 case B43_ANTENNA1: 1591 return B43_TXH_PHY_ANT1; 1592 case B43_ANTENNA2: 1593 return B43_TXH_PHY_ANT2; 1594 case B43_ANTENNA3: 1595 return B43_TXH_PHY_ANT3; 1596 case B43_ANTENNA_AUTO0: 1597 case B43_ANTENNA_AUTO1: 1598 return B43_TXH_PHY_ANT01AUTO; 1599 } 1600 B43_WARN_ON(1); 1601 return 0; 1602 } 1603 1604 static void b43_write_beacon_template(struct b43_wldev *dev, 1605 u16 ram_offset, 1606 u16 shm_size_offset) 1607 { 1608 unsigned int i, len, variable_len; 1609 const struct ieee80211_mgmt *bcn; 1610 const u8 *ie; 1611 bool tim_found = false; 1612 unsigned int rate; 1613 u16 ctl; 1614 int antenna; 1615 struct ieee80211_tx_info *info; 1616 unsigned long flags; 1617 struct sk_buff *beacon_skb; 1618 1619 spin_lock_irqsave(&dev->wl->beacon_lock, flags); 1620 info = IEEE80211_SKB_CB(dev->wl->current_beacon); 1621 rate = ieee80211_get_tx_rate(dev->wl->hw, info)->hw_value; 1622 /* Clone the beacon, so it cannot go away, while we write it to hw. */ 1623 beacon_skb = skb_clone(dev->wl->current_beacon, GFP_ATOMIC); 1624 spin_unlock_irqrestore(&dev->wl->beacon_lock, flags); 1625 1626 if (!beacon_skb) { 1627 b43dbg(dev->wl, "Could not upload beacon. " 1628 "Failed to clone beacon skb."); 1629 return; 1630 } 1631 1632 bcn = (const struct ieee80211_mgmt *)(beacon_skb->data); 1633 len = min_t(size_t, beacon_skb->len, 1634 0x200 - sizeof(struct b43_plcp_hdr6)); 1635 1636 b43_write_template_common(dev, (const u8 *)bcn, 1637 len, ram_offset, shm_size_offset, rate); 1638 1639 /* Write the PHY TX control parameters. */ 1640 antenna = B43_ANTENNA_DEFAULT; 1641 antenna = b43_antenna_to_phyctl(antenna); 1642 ctl = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_BEACPHYCTL); 1643 /* We can't send beacons with short preamble. Would get PHY errors. */ 1644 ctl &= ~B43_TXH_PHY_SHORTPRMBL; 1645 ctl &= ~B43_TXH_PHY_ANT; 1646 ctl &= ~B43_TXH_PHY_ENC; 1647 ctl |= antenna; 1648 if (b43_is_cck_rate(rate)) 1649 ctl |= B43_TXH_PHY_ENC_CCK; 1650 else 1651 ctl |= B43_TXH_PHY_ENC_OFDM; 1652 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_BEACPHYCTL, ctl); 1653 1654 /* Find the position of the TIM and the DTIM_period value 1655 * and write them to SHM. */ 1656 ie = bcn->u.beacon.variable; 1657 variable_len = len - offsetof(struct ieee80211_mgmt, u.beacon.variable); 1658 for (i = 0; i < variable_len - 2; ) { 1659 uint8_t ie_id, ie_len; 1660 1661 ie_id = ie[i]; 1662 ie_len = ie[i + 1]; 1663 if (ie_id == 5) { 1664 u16 tim_position; 1665 u16 dtim_period; 1666 /* This is the TIM Information Element */ 1667 1668 /* Check whether the ie_len is in the beacon data range. */ 1669 if (variable_len < ie_len + 2 + i) 1670 break; 1671 /* A valid TIM is at least 4 bytes long. */ 1672 if (ie_len < 4) 1673 break; 1674 tim_found = true; 1675 1676 tim_position = sizeof(struct b43_plcp_hdr6); 1677 tim_position += offsetof(struct ieee80211_mgmt, u.beacon.variable); 1678 tim_position += i; 1679 1680 dtim_period = ie[i + 3]; 1681 1682 b43_shm_write16(dev, B43_SHM_SHARED, 1683 B43_SHM_SH_TIMBPOS, tim_position); 1684 b43_shm_write16(dev, B43_SHM_SHARED, 1685 B43_SHM_SH_DTIMPER, dtim_period); 1686 break; 1687 } 1688 i += ie_len + 2; 1689 } 1690 if (!tim_found) { 1691 /* 1692 * If ucode wants to modify TIM do it behind the beacon, this 1693 * will happen, for example, when doing mesh networking. 1694 */ 1695 b43_shm_write16(dev, B43_SHM_SHARED, 1696 B43_SHM_SH_TIMBPOS, 1697 len + sizeof(struct b43_plcp_hdr6)); 1698 b43_shm_write16(dev, B43_SHM_SHARED, 1699 B43_SHM_SH_DTIMPER, 0); 1700 } 1701 b43dbg(dev->wl, "Updated beacon template at 0x%x\n", ram_offset); 1702 1703 dev_kfree_skb_any(beacon_skb); 1704 } 1705 1706 static void b43_upload_beacon0(struct b43_wldev *dev) 1707 { 1708 struct b43_wl *wl = dev->wl; 1709 1710 if (wl->beacon0_uploaded) 1711 return; 1712 b43_write_beacon_template(dev, B43_SHM_SH_BT_BASE0, B43_SHM_SH_BTL0); 1713 wl->beacon0_uploaded = true; 1714 } 1715 1716 static void b43_upload_beacon1(struct b43_wldev *dev) 1717 { 1718 struct b43_wl *wl = dev->wl; 1719 1720 if (wl->beacon1_uploaded) 1721 return; 1722 b43_write_beacon_template(dev, B43_SHM_SH_BT_BASE1, B43_SHM_SH_BTL1); 1723 wl->beacon1_uploaded = true; 1724 } 1725 1726 static void handle_irq_beacon(struct b43_wldev *dev) 1727 { 1728 struct b43_wl *wl = dev->wl; 1729 u32 cmd, beacon0_valid, beacon1_valid; 1730 1731 if (!b43_is_mode(wl, NL80211_IFTYPE_AP) && 1732 !b43_is_mode(wl, NL80211_IFTYPE_MESH_POINT) && 1733 !b43_is_mode(wl, NL80211_IFTYPE_ADHOC)) 1734 return; 1735 1736 /* This is the bottom half of the asynchronous beacon update. */ 1737 1738 /* Ignore interrupt in the future. */ 1739 dev->irq_mask &= ~B43_IRQ_BEACON; 1740 1741 cmd = b43_read32(dev, B43_MMIO_MACCMD); 1742 beacon0_valid = (cmd & B43_MACCMD_BEACON0_VALID); 1743 beacon1_valid = (cmd & B43_MACCMD_BEACON1_VALID); 1744 1745 /* Schedule interrupt manually, if busy. */ 1746 if (beacon0_valid && beacon1_valid) { 1747 b43_write32(dev, B43_MMIO_GEN_IRQ_REASON, B43_IRQ_BEACON); 1748 dev->irq_mask |= B43_IRQ_BEACON; 1749 return; 1750 } 1751 1752 if (unlikely(wl->beacon_templates_virgin)) { 1753 /* We never uploaded a beacon before. 1754 * Upload both templates now, but only mark one valid. */ 1755 wl->beacon_templates_virgin = false; 1756 b43_upload_beacon0(dev); 1757 b43_upload_beacon1(dev); 1758 cmd = b43_read32(dev, B43_MMIO_MACCMD); 1759 cmd |= B43_MACCMD_BEACON0_VALID; 1760 b43_write32(dev, B43_MMIO_MACCMD, cmd); 1761 } else { 1762 if (!beacon0_valid) { 1763 b43_upload_beacon0(dev); 1764 cmd = b43_read32(dev, B43_MMIO_MACCMD); 1765 cmd |= B43_MACCMD_BEACON0_VALID; 1766 b43_write32(dev, B43_MMIO_MACCMD, cmd); 1767 } else if (!beacon1_valid) { 1768 b43_upload_beacon1(dev); 1769 cmd = b43_read32(dev, B43_MMIO_MACCMD); 1770 cmd |= B43_MACCMD_BEACON1_VALID; 1771 b43_write32(dev, B43_MMIO_MACCMD, cmd); 1772 } 1773 } 1774 } 1775 1776 static void b43_do_beacon_update_trigger_work(struct b43_wldev *dev) 1777 { 1778 u32 old_irq_mask = dev->irq_mask; 1779 1780 /* update beacon right away or defer to irq */ 1781 handle_irq_beacon(dev); 1782 if (old_irq_mask != dev->irq_mask) { 1783 /* The handler updated the IRQ mask. */ 1784 B43_WARN_ON(!dev->irq_mask); 1785 if (b43_read32(dev, B43_MMIO_GEN_IRQ_MASK)) { 1786 b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, dev->irq_mask); 1787 } else { 1788 /* Device interrupts are currently disabled. That means 1789 * we just ran the hardirq handler and scheduled the 1790 * IRQ thread. The thread will write the IRQ mask when 1791 * it finished, so there's nothing to do here. Writing 1792 * the mask _here_ would incorrectly re-enable IRQs. */ 1793 } 1794 } 1795 } 1796 1797 static void b43_beacon_update_trigger_work(struct work_struct *work) 1798 { 1799 struct b43_wl *wl = container_of(work, struct b43_wl, 1800 beacon_update_trigger); 1801 struct b43_wldev *dev; 1802 1803 mutex_lock(&wl->mutex); 1804 dev = wl->current_dev; 1805 if (likely(dev && (b43_status(dev) >= B43_STAT_INITIALIZED))) { 1806 if (b43_bus_host_is_sdio(dev->dev)) { 1807 /* wl->mutex is enough. */ 1808 b43_do_beacon_update_trigger_work(dev); 1809 } else { 1810 spin_lock_irq(&wl->hardirq_lock); 1811 b43_do_beacon_update_trigger_work(dev); 1812 spin_unlock_irq(&wl->hardirq_lock); 1813 } 1814 } 1815 mutex_unlock(&wl->mutex); 1816 } 1817 1818 /* Asynchronously update the packet templates in template RAM. */ 1819 static void b43_update_templates(struct b43_wl *wl) 1820 { 1821 struct sk_buff *beacon, *old_beacon; 1822 unsigned long flags; 1823 1824 /* This is the top half of the asynchronous beacon update. 1825 * The bottom half is the beacon IRQ. 1826 * Beacon update must be asynchronous to avoid sending an 1827 * invalid beacon. This can happen for example, if the firmware 1828 * transmits a beacon while we are updating it. */ 1829 1830 /* We could modify the existing beacon and set the aid bit in 1831 * the TIM field, but that would probably require resizing and 1832 * moving of data within the beacon template. 1833 * Simply request a new beacon and let mac80211 do the hard work. */ 1834 beacon = ieee80211_beacon_get(wl->hw, wl->vif); 1835 if (unlikely(!beacon)) 1836 return; 1837 1838 spin_lock_irqsave(&wl->beacon_lock, flags); 1839 old_beacon = wl->current_beacon; 1840 wl->current_beacon = beacon; 1841 wl->beacon0_uploaded = false; 1842 wl->beacon1_uploaded = false; 1843 spin_unlock_irqrestore(&wl->beacon_lock, flags); 1844 1845 ieee80211_queue_work(wl->hw, &wl->beacon_update_trigger); 1846 1847 if (old_beacon) 1848 dev_kfree_skb_any(old_beacon); 1849 } 1850 1851 static void b43_set_beacon_int(struct b43_wldev *dev, u16 beacon_int) 1852 { 1853 b43_time_lock(dev); 1854 if (dev->dev->core_rev >= 3) { 1855 b43_write32(dev, B43_MMIO_TSF_CFP_REP, (beacon_int << 16)); 1856 b43_write32(dev, B43_MMIO_TSF_CFP_START, (beacon_int << 10)); 1857 } else { 1858 b43_write16(dev, 0x606, (beacon_int >> 6)); 1859 b43_write16(dev, 0x610, beacon_int); 1860 } 1861 b43_time_unlock(dev); 1862 b43dbg(dev->wl, "Set beacon interval to %u\n", beacon_int); 1863 } 1864 1865 static void b43_handle_firmware_panic(struct b43_wldev *dev) 1866 { 1867 u16 reason; 1868 1869 /* Read the register that contains the reason code for the panic. */ 1870 reason = b43_shm_read16(dev, B43_SHM_SCRATCH, B43_FWPANIC_REASON_REG); 1871 b43err(dev->wl, "Whoopsy, firmware panic! Reason: %u\n", reason); 1872 1873 switch (reason) { 1874 default: 1875 b43dbg(dev->wl, "The panic reason is unknown.\n"); 1876 /* fallthrough */ 1877 case B43_FWPANIC_DIE: 1878 /* Do not restart the controller or firmware. 1879 * The device is nonfunctional from now on. 1880 * Restarting would result in this panic to trigger again, 1881 * so we avoid that recursion. */ 1882 break; 1883 case B43_FWPANIC_RESTART: 1884 b43_controller_restart(dev, "Microcode panic"); 1885 break; 1886 } 1887 } 1888 1889 static void handle_irq_ucode_debug(struct b43_wldev *dev) 1890 { 1891 unsigned int i, cnt; 1892 u16 reason, marker_id, marker_line; 1893 __le16 *buf; 1894 1895 /* The proprietary firmware doesn't have this IRQ. */ 1896 if (!dev->fw.opensource) 1897 return; 1898 1899 /* Read the register that contains the reason code for this IRQ. */ 1900 reason = b43_shm_read16(dev, B43_SHM_SCRATCH, B43_DEBUGIRQ_REASON_REG); 1901 1902 switch (reason) { 1903 case B43_DEBUGIRQ_PANIC: 1904 b43_handle_firmware_panic(dev); 1905 break; 1906 case B43_DEBUGIRQ_DUMP_SHM: 1907 if (!B43_DEBUG) 1908 break; /* Only with driver debugging enabled. */ 1909 buf = kmalloc(4096, GFP_ATOMIC); 1910 if (!buf) { 1911 b43dbg(dev->wl, "SHM-dump: Failed to allocate memory\n"); 1912 goto out; 1913 } 1914 for (i = 0; i < 4096; i += 2) { 1915 u16 tmp = b43_shm_read16(dev, B43_SHM_SHARED, i); 1916 buf[i / 2] = cpu_to_le16(tmp); 1917 } 1918 b43info(dev->wl, "Shared memory dump:\n"); 1919 print_hex_dump(KERN_INFO, "", DUMP_PREFIX_OFFSET, 1920 16, 2, buf, 4096, 1); 1921 kfree(buf); 1922 break; 1923 case B43_DEBUGIRQ_DUMP_REGS: 1924 if (!B43_DEBUG) 1925 break; /* Only with driver debugging enabled. */ 1926 b43info(dev->wl, "Microcode register dump:\n"); 1927 for (i = 0, cnt = 0; i < 64; i++) { 1928 u16 tmp = b43_shm_read16(dev, B43_SHM_SCRATCH, i); 1929 if (cnt == 0) 1930 printk(KERN_INFO); 1931 printk("r%02u: 0x%04X ", i, tmp); 1932 cnt++; 1933 if (cnt == 6) { 1934 printk("\n"); 1935 cnt = 0; 1936 } 1937 } 1938 printk("\n"); 1939 break; 1940 case B43_DEBUGIRQ_MARKER: 1941 if (!B43_DEBUG) 1942 break; /* Only with driver debugging enabled. */ 1943 marker_id = b43_shm_read16(dev, B43_SHM_SCRATCH, 1944 B43_MARKER_ID_REG); 1945 marker_line = b43_shm_read16(dev, B43_SHM_SCRATCH, 1946 B43_MARKER_LINE_REG); 1947 b43info(dev->wl, "The firmware just executed the MARKER(%u) " 1948 "at line number %u\n", 1949 marker_id, marker_line); 1950 break; 1951 default: 1952 b43dbg(dev->wl, "Debug-IRQ triggered for unknown reason: %u\n", 1953 reason); 1954 } 1955 out: 1956 /* Acknowledge the debug-IRQ, so the firmware can continue. */ 1957 b43_shm_write16(dev, B43_SHM_SCRATCH, 1958 B43_DEBUGIRQ_REASON_REG, B43_DEBUGIRQ_ACK); 1959 } 1960 1961 static void b43_do_interrupt_thread(struct b43_wldev *dev) 1962 { 1963 u32 reason; 1964 u32 dma_reason[ARRAY_SIZE(dev->dma_reason)]; 1965 u32 merged_dma_reason = 0; 1966 int i; 1967 1968 if (unlikely(b43_status(dev) != B43_STAT_STARTED)) 1969 return; 1970 1971 reason = dev->irq_reason; 1972 for (i = 0; i < ARRAY_SIZE(dma_reason); i++) { 1973 dma_reason[i] = dev->dma_reason[i]; 1974 merged_dma_reason |= dma_reason[i]; 1975 } 1976 1977 if (unlikely(reason & B43_IRQ_MAC_TXERR)) 1978 b43err(dev->wl, "MAC transmission error\n"); 1979 1980 if (unlikely(reason & B43_IRQ_PHY_TXERR)) { 1981 b43err(dev->wl, "PHY transmission error\n"); 1982 rmb(); 1983 if (unlikely(atomic_dec_and_test(&dev->phy.txerr_cnt))) { 1984 atomic_set(&dev->phy.txerr_cnt, 1985 B43_PHY_TX_BADNESS_LIMIT); 1986 b43err(dev->wl, "Too many PHY TX errors, " 1987 "restarting the controller\n"); 1988 b43_controller_restart(dev, "PHY TX errors"); 1989 } 1990 } 1991 1992 if (unlikely(merged_dma_reason & (B43_DMAIRQ_FATALMASK))) { 1993 b43err(dev->wl, 1994 "Fatal DMA error: 0x%08X, 0x%08X, 0x%08X, 0x%08X, 0x%08X, 0x%08X\n", 1995 dma_reason[0], dma_reason[1], 1996 dma_reason[2], dma_reason[3], 1997 dma_reason[4], dma_reason[5]); 1998 b43err(dev->wl, "This device does not support DMA " 1999 "on your system. It will now be switched to PIO.\n"); 2000 /* Fall back to PIO transfers if we get fatal DMA errors! */ 2001 dev->use_pio = true; 2002 b43_controller_restart(dev, "DMA error"); 2003 return; 2004 } 2005 2006 if (unlikely(reason & B43_IRQ_UCODE_DEBUG)) 2007 handle_irq_ucode_debug(dev); 2008 if (reason & B43_IRQ_TBTT_INDI) 2009 handle_irq_tbtt_indication(dev); 2010 if (reason & B43_IRQ_ATIM_END) 2011 handle_irq_atim_end(dev); 2012 if (reason & B43_IRQ_BEACON) 2013 handle_irq_beacon(dev); 2014 if (reason & B43_IRQ_PMQ) 2015 handle_irq_pmq(dev); 2016 if (reason & B43_IRQ_TXFIFO_FLUSH_OK) 2017 ;/* TODO */ 2018 if (reason & B43_IRQ_NOISESAMPLE_OK) 2019 handle_irq_noise(dev); 2020 2021 /* Check the DMA reason registers for received data. */ 2022 if (dma_reason[0] & B43_DMAIRQ_RDESC_UFLOW) { 2023 if (B43_DEBUG) 2024 b43warn(dev->wl, "RX descriptor underrun\n"); 2025 b43_dma_handle_rx_overflow(dev->dma.rx_ring); 2026 } 2027 if (dma_reason[0] & B43_DMAIRQ_RX_DONE) { 2028 if (b43_using_pio_transfers(dev)) 2029 b43_pio_rx(dev->pio.rx_queue); 2030 else 2031 b43_dma_rx(dev->dma.rx_ring); 2032 } 2033 B43_WARN_ON(dma_reason[1] & B43_DMAIRQ_RX_DONE); 2034 B43_WARN_ON(dma_reason[2] & B43_DMAIRQ_RX_DONE); 2035 B43_WARN_ON(dma_reason[3] & B43_DMAIRQ_RX_DONE); 2036 B43_WARN_ON(dma_reason[4] & B43_DMAIRQ_RX_DONE); 2037 B43_WARN_ON(dma_reason[5] & B43_DMAIRQ_RX_DONE); 2038 2039 if (reason & B43_IRQ_TX_OK) 2040 handle_irq_transmit_status(dev); 2041 2042 /* Re-enable interrupts on the device by restoring the current interrupt mask. */ 2043 b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, dev->irq_mask); 2044 2045 #if B43_DEBUG 2046 if (b43_debug(dev, B43_DBG_VERBOSESTATS)) { 2047 dev->irq_count++; 2048 for (i = 0; i < ARRAY_SIZE(dev->irq_bit_count); i++) { 2049 if (reason & (1 << i)) 2050 dev->irq_bit_count[i]++; 2051 } 2052 } 2053 #endif 2054 } 2055 2056 /* Interrupt thread handler. Handles device interrupts in thread context. */ 2057 static irqreturn_t b43_interrupt_thread_handler(int irq, void *dev_id) 2058 { 2059 struct b43_wldev *dev = dev_id; 2060 2061 mutex_lock(&dev->wl->mutex); 2062 b43_do_interrupt_thread(dev); 2063 mutex_unlock(&dev->wl->mutex); 2064 2065 return IRQ_HANDLED; 2066 } 2067 2068 static irqreturn_t b43_do_interrupt(struct b43_wldev *dev) 2069 { 2070 u32 reason; 2071 2072 /* This code runs under wl->hardirq_lock, but _only_ on non-SDIO busses. 2073 * On SDIO, this runs under wl->mutex. */ 2074 2075 reason = b43_read32(dev, B43_MMIO_GEN_IRQ_REASON); 2076 if (reason == 0xffffffff) /* shared IRQ */ 2077 return IRQ_NONE; 2078 reason &= dev->irq_mask; 2079 if (!reason) 2080 return IRQ_NONE; 2081 2082 dev->dma_reason[0] = b43_read32(dev, B43_MMIO_DMA0_REASON) 2083 & 0x0001FC00; 2084 dev->dma_reason[1] = b43_read32(dev, B43_MMIO_DMA1_REASON) 2085 & 0x0000DC00; 2086 dev->dma_reason[2] = b43_read32(dev, B43_MMIO_DMA2_REASON) 2087 & 0x0000DC00; 2088 dev->dma_reason[3] = b43_read32(dev, B43_MMIO_DMA3_REASON) 2089 & 0x0001DC00; 2090 dev->dma_reason[4] = b43_read32(dev, B43_MMIO_DMA4_REASON) 2091 & 0x0000DC00; 2092 /* Unused ring 2093 dev->dma_reason[5] = b43_read32(dev, B43_MMIO_DMA5_REASON) 2094 & 0x0000DC00; 2095 */ 2096 2097 /* ACK the interrupt. */ 2098 b43_write32(dev, B43_MMIO_GEN_IRQ_REASON, reason); 2099 b43_write32(dev, B43_MMIO_DMA0_REASON, dev->dma_reason[0]); 2100 b43_write32(dev, B43_MMIO_DMA1_REASON, dev->dma_reason[1]); 2101 b43_write32(dev, B43_MMIO_DMA2_REASON, dev->dma_reason[2]); 2102 b43_write32(dev, B43_MMIO_DMA3_REASON, dev->dma_reason[3]); 2103 b43_write32(dev, B43_MMIO_DMA4_REASON, dev->dma_reason[4]); 2104 /* Unused ring 2105 b43_write32(dev, B43_MMIO_DMA5_REASON, dev->dma_reason[5]); 2106 */ 2107 2108 /* Disable IRQs on the device. The IRQ thread handler will re-enable them. */ 2109 b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, 0); 2110 /* Save the reason bitmasks for the IRQ thread handler. */ 2111 dev->irq_reason = reason; 2112 2113 return IRQ_WAKE_THREAD; 2114 } 2115 2116 /* Interrupt handler top-half. This runs with interrupts disabled. */ 2117 static irqreturn_t b43_interrupt_handler(int irq, void *dev_id) 2118 { 2119 struct b43_wldev *dev = dev_id; 2120 irqreturn_t ret; 2121 2122 if (unlikely(b43_status(dev) < B43_STAT_STARTED)) 2123 return IRQ_NONE; 2124 2125 spin_lock(&dev->wl->hardirq_lock); 2126 ret = b43_do_interrupt(dev); 2127 spin_unlock(&dev->wl->hardirq_lock); 2128 2129 return ret; 2130 } 2131 2132 /* SDIO interrupt handler. This runs in process context. */ 2133 static void b43_sdio_interrupt_handler(struct b43_wldev *dev) 2134 { 2135 struct b43_wl *wl = dev->wl; 2136 irqreturn_t ret; 2137 2138 mutex_lock(&wl->mutex); 2139 2140 ret = b43_do_interrupt(dev); 2141 if (ret == IRQ_WAKE_THREAD) 2142 b43_do_interrupt_thread(dev); 2143 2144 mutex_unlock(&wl->mutex); 2145 } 2146 2147 void b43_do_release_fw(struct b43_firmware_file *fw) 2148 { 2149 release_firmware(fw->data); 2150 fw->data = NULL; 2151 fw->filename = NULL; 2152 } 2153 2154 static void b43_release_firmware(struct b43_wldev *dev) 2155 { 2156 complete(&dev->fw_load_complete); 2157 b43_do_release_fw(&dev->fw.ucode); 2158 b43_do_release_fw(&dev->fw.pcm); 2159 b43_do_release_fw(&dev->fw.initvals); 2160 b43_do_release_fw(&dev->fw.initvals_band); 2161 } 2162 2163 static void b43_print_fw_helptext(struct b43_wl *wl, bool error) 2164 { 2165 const char text[] = 2166 "You must go to " \ 2167 "http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware " \ 2168 "and download the correct firmware for this driver version. " \ 2169 "Please carefully read all instructions on this website.\n"; 2170 2171 if (error) 2172 b43err(wl, text); 2173 else 2174 b43warn(wl, text); 2175 } 2176 2177 static void b43_fw_cb(const struct firmware *firmware, void *context) 2178 { 2179 struct b43_request_fw_context *ctx = context; 2180 2181 ctx->blob = firmware; 2182 complete(&ctx->dev->fw_load_complete); 2183 } 2184 2185 int b43_do_request_fw(struct b43_request_fw_context *ctx, 2186 const char *name, 2187 struct b43_firmware_file *fw, bool async) 2188 { 2189 struct b43_fw_header *hdr; 2190 u32 size; 2191 int err; 2192 2193 if (!name) { 2194 /* Don't fetch anything. Free possibly cached firmware. */ 2195 /* FIXME: We should probably keep it anyway, to save some headache 2196 * on suspend/resume with multiband devices. */ 2197 b43_do_release_fw(fw); 2198 return 0; 2199 } 2200 if (fw->filename) { 2201 if ((fw->type == ctx->req_type) && 2202 (strcmp(fw->filename, name) == 0)) 2203 return 0; /* Already have this fw. */ 2204 /* Free the cached firmware first. */ 2205 /* FIXME: We should probably do this later after we successfully 2206 * got the new fw. This could reduce headache with multiband devices. 2207 * We could also redesign this to cache the firmware for all possible 2208 * bands all the time. */ 2209 b43_do_release_fw(fw); 2210 } 2211 2212 switch (ctx->req_type) { 2213 case B43_FWTYPE_PROPRIETARY: 2214 snprintf(ctx->fwname, sizeof(ctx->fwname), 2215 "b43%s/%s.fw", 2216 modparam_fwpostfix, name); 2217 break; 2218 case B43_FWTYPE_OPENSOURCE: 2219 snprintf(ctx->fwname, sizeof(ctx->fwname), 2220 "b43-open%s/%s.fw", 2221 modparam_fwpostfix, name); 2222 break; 2223 default: 2224 B43_WARN_ON(1); 2225 return -ENOSYS; 2226 } 2227 if (async) { 2228 /* do this part asynchronously */ 2229 init_completion(&ctx->dev->fw_load_complete); 2230 err = request_firmware_nowait(THIS_MODULE, 1, ctx->fwname, 2231 ctx->dev->dev->dev, GFP_KERNEL, 2232 ctx, b43_fw_cb); 2233 if (err < 0) { 2234 pr_err("Unable to load firmware\n"); 2235 return err; 2236 } 2237 wait_for_completion(&ctx->dev->fw_load_complete); 2238 if (ctx->blob) 2239 goto fw_ready; 2240 /* On some ARM systems, the async request will fail, but the next sync 2241 * request works. For this reason, we fall through here 2242 */ 2243 } 2244 err = request_firmware(&ctx->blob, ctx->fwname, 2245 ctx->dev->dev->dev); 2246 if (err == -ENOENT) { 2247 snprintf(ctx->errors[ctx->req_type], 2248 sizeof(ctx->errors[ctx->req_type]), 2249 "Firmware file \"%s\" not found\n", 2250 ctx->fwname); 2251 return err; 2252 } else if (err) { 2253 snprintf(ctx->errors[ctx->req_type], 2254 sizeof(ctx->errors[ctx->req_type]), 2255 "Firmware file \"%s\" request failed (err=%d)\n", 2256 ctx->fwname, err); 2257 return err; 2258 } 2259 fw_ready: 2260 if (ctx->blob->size < sizeof(struct b43_fw_header)) 2261 goto err_format; 2262 hdr = (struct b43_fw_header *)(ctx->blob->data); 2263 switch (hdr->type) { 2264 case B43_FW_TYPE_UCODE: 2265 case B43_FW_TYPE_PCM: 2266 size = be32_to_cpu(hdr->size); 2267 if (size != ctx->blob->size - sizeof(struct b43_fw_header)) 2268 goto err_format; 2269 /* fallthrough */ 2270 case B43_FW_TYPE_IV: 2271 if (hdr->ver != 1) 2272 goto err_format; 2273 break; 2274 default: 2275 goto err_format; 2276 } 2277 2278 fw->data = ctx->blob; 2279 fw->filename = name; 2280 fw->type = ctx->req_type; 2281 2282 return 0; 2283 2284 err_format: 2285 snprintf(ctx->errors[ctx->req_type], 2286 sizeof(ctx->errors[ctx->req_type]), 2287 "Firmware file \"%s\" format error.\n", ctx->fwname); 2288 release_firmware(ctx->blob); 2289 2290 return -EPROTO; 2291 } 2292 2293 /* http://bcm-v4.sipsolutions.net/802.11/Init/Firmware */ 2294 static int b43_try_request_fw(struct b43_request_fw_context *ctx) 2295 { 2296 struct b43_wldev *dev = ctx->dev; 2297 struct b43_firmware *fw = &ctx->dev->fw; 2298 struct b43_phy *phy = &dev->phy; 2299 const u8 rev = ctx->dev->dev->core_rev; 2300 const char *filename; 2301 int err; 2302 2303 /* Get microcode */ 2304 filename = NULL; 2305 switch (rev) { 2306 case 42: 2307 if (phy->type == B43_PHYTYPE_AC) 2308 filename = "ucode42"; 2309 break; 2310 case 40: 2311 if (phy->type == B43_PHYTYPE_AC) 2312 filename = "ucode40"; 2313 break; 2314 case 33: 2315 if (phy->type == B43_PHYTYPE_LCN40) 2316 filename = "ucode33_lcn40"; 2317 break; 2318 case 30: 2319 if (phy->type == B43_PHYTYPE_N) 2320 filename = "ucode30_mimo"; 2321 break; 2322 case 29: 2323 if (phy->type == B43_PHYTYPE_HT) 2324 filename = "ucode29_mimo"; 2325 break; 2326 case 26: 2327 if (phy->type == B43_PHYTYPE_HT) 2328 filename = "ucode26_mimo"; 2329 break; 2330 case 28: 2331 case 25: 2332 if (phy->type == B43_PHYTYPE_N) 2333 filename = "ucode25_mimo"; 2334 else if (phy->type == B43_PHYTYPE_LCN) 2335 filename = "ucode25_lcn"; 2336 break; 2337 case 24: 2338 if (phy->type == B43_PHYTYPE_LCN) 2339 filename = "ucode24_lcn"; 2340 break; 2341 case 23: 2342 if (phy->type == B43_PHYTYPE_N) 2343 filename = "ucode16_mimo"; 2344 break; 2345 case 16 ... 19: 2346 if (phy->type == B43_PHYTYPE_N) 2347 filename = "ucode16_mimo"; 2348 else if (phy->type == B43_PHYTYPE_LP) 2349 filename = "ucode16_lp"; 2350 break; 2351 case 15: 2352 filename = "ucode15"; 2353 break; 2354 case 14: 2355 filename = "ucode14"; 2356 break; 2357 case 13: 2358 filename = "ucode13"; 2359 break; 2360 case 11 ... 12: 2361 filename = "ucode11"; 2362 break; 2363 case 5 ... 10: 2364 filename = "ucode5"; 2365 break; 2366 } 2367 if (!filename) 2368 goto err_no_ucode; 2369 err = b43_do_request_fw(ctx, filename, &fw->ucode, true); 2370 if (err) 2371 goto err_load; 2372 2373 /* Get PCM code */ 2374 if ((rev >= 5) && (rev <= 10)) 2375 filename = "pcm5"; 2376 else if (rev >= 11) 2377 filename = NULL; 2378 else 2379 goto err_no_pcm; 2380 fw->pcm_request_failed = false; 2381 err = b43_do_request_fw(ctx, filename, &fw->pcm, false); 2382 if (err == -ENOENT) { 2383 /* We did not find a PCM file? Not fatal, but 2384 * core rev <= 10 must do without hwcrypto then. */ 2385 fw->pcm_request_failed = true; 2386 } else if (err) 2387 goto err_load; 2388 2389 /* Get initvals */ 2390 filename = NULL; 2391 switch (dev->phy.type) { 2392 case B43_PHYTYPE_G: 2393 if (rev == 13) 2394 filename = "b0g0initvals13"; 2395 else if (rev >= 5 && rev <= 10) 2396 filename = "b0g0initvals5"; 2397 break; 2398 case B43_PHYTYPE_N: 2399 if (rev == 30) 2400 filename = "n16initvals30"; 2401 else if (rev == 28 || rev == 25) 2402 filename = "n0initvals25"; 2403 else if (rev == 24) 2404 filename = "n0initvals24"; 2405 else if (rev == 23) 2406 filename = "n0initvals16"; /* What about n0initvals22? */ 2407 else if (rev >= 16 && rev <= 18) 2408 filename = "n0initvals16"; 2409 else if (rev >= 11 && rev <= 12) 2410 filename = "n0initvals11"; 2411 break; 2412 case B43_PHYTYPE_LP: 2413 if (rev >= 16 && rev <= 18) 2414 filename = "lp0initvals16"; 2415 else if (rev == 15) 2416 filename = "lp0initvals15"; 2417 else if (rev == 14) 2418 filename = "lp0initvals14"; 2419 else if (rev == 13) 2420 filename = "lp0initvals13"; 2421 break; 2422 case B43_PHYTYPE_HT: 2423 if (rev == 29) 2424 filename = "ht0initvals29"; 2425 else if (rev == 26) 2426 filename = "ht0initvals26"; 2427 break; 2428 case B43_PHYTYPE_LCN: 2429 if (rev == 24) 2430 filename = "lcn0initvals24"; 2431 break; 2432 case B43_PHYTYPE_LCN40: 2433 if (rev == 33) 2434 filename = "lcn400initvals33"; 2435 break; 2436 case B43_PHYTYPE_AC: 2437 if (rev == 42) 2438 filename = "ac1initvals42"; 2439 else if (rev == 40) 2440 filename = "ac0initvals40"; 2441 break; 2442 } 2443 if (!filename) 2444 goto err_no_initvals; 2445 err = b43_do_request_fw(ctx, filename, &fw->initvals, false); 2446 if (err) 2447 goto err_load; 2448 2449 /* Get bandswitch initvals */ 2450 filename = NULL; 2451 switch (dev->phy.type) { 2452 case B43_PHYTYPE_G: 2453 if (rev == 13) 2454 filename = "b0g0bsinitvals13"; 2455 else if (rev >= 5 && rev <= 10) 2456 filename = "b0g0bsinitvals5"; 2457 break; 2458 case B43_PHYTYPE_N: 2459 if (rev == 30) 2460 filename = "n16bsinitvals30"; 2461 else if (rev == 28 || rev == 25) 2462 filename = "n0bsinitvals25"; 2463 else if (rev == 24) 2464 filename = "n0bsinitvals24"; 2465 else if (rev == 23) 2466 filename = "n0bsinitvals16"; /* What about n0bsinitvals22? */ 2467 else if (rev >= 16 && rev <= 18) 2468 filename = "n0bsinitvals16"; 2469 else if (rev >= 11 && rev <= 12) 2470 filename = "n0bsinitvals11"; 2471 break; 2472 case B43_PHYTYPE_LP: 2473 if (rev >= 16 && rev <= 18) 2474 filename = "lp0bsinitvals16"; 2475 else if (rev == 15) 2476 filename = "lp0bsinitvals15"; 2477 else if (rev == 14) 2478 filename = "lp0bsinitvals14"; 2479 else if (rev == 13) 2480 filename = "lp0bsinitvals13"; 2481 break; 2482 case B43_PHYTYPE_HT: 2483 if (rev == 29) 2484 filename = "ht0bsinitvals29"; 2485 else if (rev == 26) 2486 filename = "ht0bsinitvals26"; 2487 break; 2488 case B43_PHYTYPE_LCN: 2489 if (rev == 24) 2490 filename = "lcn0bsinitvals24"; 2491 break; 2492 case B43_PHYTYPE_LCN40: 2493 if (rev == 33) 2494 filename = "lcn400bsinitvals33"; 2495 break; 2496 case B43_PHYTYPE_AC: 2497 if (rev == 42) 2498 filename = "ac1bsinitvals42"; 2499 else if (rev == 40) 2500 filename = "ac0bsinitvals40"; 2501 break; 2502 } 2503 if (!filename) 2504 goto err_no_initvals; 2505 err = b43_do_request_fw(ctx, filename, &fw->initvals_band, false); 2506 if (err) 2507 goto err_load; 2508 2509 fw->opensource = (ctx->req_type == B43_FWTYPE_OPENSOURCE); 2510 2511 return 0; 2512 2513 err_no_ucode: 2514 err = ctx->fatal_failure = -EOPNOTSUPP; 2515 b43err(dev->wl, "The driver does not know which firmware (ucode) " 2516 "is required for your device (wl-core rev %u)\n", rev); 2517 goto error; 2518 2519 err_no_pcm: 2520 err = ctx->fatal_failure = -EOPNOTSUPP; 2521 b43err(dev->wl, "The driver does not know which firmware (PCM) " 2522 "is required for your device (wl-core rev %u)\n", rev); 2523 goto error; 2524 2525 err_no_initvals: 2526 err = ctx->fatal_failure = -EOPNOTSUPP; 2527 b43err(dev->wl, "The driver does not know which firmware (initvals) " 2528 "is required for your device (wl-core rev %u)\n", rev); 2529 goto error; 2530 2531 err_load: 2532 /* We failed to load this firmware image. The error message 2533 * already is in ctx->errors. Return and let our caller decide 2534 * what to do. */ 2535 goto error; 2536 2537 error: 2538 b43_release_firmware(dev); 2539 return err; 2540 } 2541 2542 static int b43_one_core_attach(struct b43_bus_dev *dev, struct b43_wl *wl); 2543 static void b43_one_core_detach(struct b43_bus_dev *dev); 2544 static int b43_rng_init(struct b43_wl *wl); 2545 2546 static void b43_request_firmware(struct work_struct *work) 2547 { 2548 struct b43_wl *wl = container_of(work, 2549 struct b43_wl, firmware_load); 2550 struct b43_wldev *dev = wl->current_dev; 2551 struct b43_request_fw_context *ctx; 2552 unsigned int i; 2553 int err; 2554 const char *errmsg; 2555 2556 ctx = kzalloc(sizeof(*ctx), GFP_KERNEL); 2557 if (!ctx) 2558 return; 2559 ctx->dev = dev; 2560 2561 ctx->req_type = B43_FWTYPE_PROPRIETARY; 2562 err = b43_try_request_fw(ctx); 2563 if (!err) 2564 goto start_ieee80211; /* Successfully loaded it. */ 2565 /* Was fw version known? */ 2566 if (ctx->fatal_failure) 2567 goto out; 2568 2569 /* proprietary fw not found, try open source */ 2570 ctx->req_type = B43_FWTYPE_OPENSOURCE; 2571 err = b43_try_request_fw(ctx); 2572 if (!err) 2573 goto start_ieee80211; /* Successfully loaded it. */ 2574 if(ctx->fatal_failure) 2575 goto out; 2576 2577 /* Could not find a usable firmware. Print the errors. */ 2578 for (i = 0; i < B43_NR_FWTYPES; i++) { 2579 errmsg = ctx->errors[i]; 2580 if (strlen(errmsg)) 2581 b43err(dev->wl, "%s", errmsg); 2582 } 2583 b43_print_fw_helptext(dev->wl, 1); 2584 goto out; 2585 2586 start_ieee80211: 2587 wl->hw->queues = B43_QOS_QUEUE_NUM; 2588 if (!modparam_qos || dev->fw.opensource) 2589 wl->hw->queues = 1; 2590 2591 err = ieee80211_register_hw(wl->hw); 2592 if (err) 2593 goto out; 2594 wl->hw_registered = true; 2595 b43_leds_register(wl->current_dev); 2596 2597 /* Register HW RNG driver */ 2598 b43_rng_init(wl); 2599 2600 out: 2601 kfree(ctx); 2602 } 2603 2604 static int b43_upload_microcode(struct b43_wldev *dev) 2605 { 2606 struct wiphy *wiphy = dev->wl->hw->wiphy; 2607 const size_t hdr_len = sizeof(struct b43_fw_header); 2608 const __be32 *data; 2609 unsigned int i, len; 2610 u16 fwrev, fwpatch, fwdate, fwtime; 2611 u32 tmp, macctl; 2612 int err = 0; 2613 2614 /* Jump the microcode PSM to offset 0 */ 2615 macctl = b43_read32(dev, B43_MMIO_MACCTL); 2616 B43_WARN_ON(macctl & B43_MACCTL_PSM_RUN); 2617 macctl |= B43_MACCTL_PSM_JMP0; 2618 b43_write32(dev, B43_MMIO_MACCTL, macctl); 2619 /* Zero out all microcode PSM registers and shared memory. */ 2620 for (i = 0; i < 64; i++) 2621 b43_shm_write16(dev, B43_SHM_SCRATCH, i, 0); 2622 for (i = 0; i < 4096; i += 2) 2623 b43_shm_write16(dev, B43_SHM_SHARED, i, 0); 2624 2625 /* Upload Microcode. */ 2626 data = (__be32 *) (dev->fw.ucode.data->data + hdr_len); 2627 len = (dev->fw.ucode.data->size - hdr_len) / sizeof(__be32); 2628 b43_shm_control_word(dev, B43_SHM_UCODE | B43_SHM_AUTOINC_W, 0x0000); 2629 for (i = 0; i < len; i++) { 2630 b43_write32(dev, B43_MMIO_SHM_DATA, be32_to_cpu(data[i])); 2631 udelay(10); 2632 } 2633 2634 if (dev->fw.pcm.data) { 2635 /* Upload PCM data. */ 2636 data = (__be32 *) (dev->fw.pcm.data->data + hdr_len); 2637 len = (dev->fw.pcm.data->size - hdr_len) / sizeof(__be32); 2638 b43_shm_control_word(dev, B43_SHM_HW, 0x01EA); 2639 b43_write32(dev, B43_MMIO_SHM_DATA, 0x00004000); 2640 /* No need for autoinc bit in SHM_HW */ 2641 b43_shm_control_word(dev, B43_SHM_HW, 0x01EB); 2642 for (i = 0; i < len; i++) { 2643 b43_write32(dev, B43_MMIO_SHM_DATA, be32_to_cpu(data[i])); 2644 udelay(10); 2645 } 2646 } 2647 2648 b43_write32(dev, B43_MMIO_GEN_IRQ_REASON, B43_IRQ_ALL); 2649 2650 /* Start the microcode PSM */ 2651 b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_PSM_JMP0, 2652 B43_MACCTL_PSM_RUN); 2653 2654 /* Wait for the microcode to load and respond */ 2655 i = 0; 2656 while (1) { 2657 tmp = b43_read32(dev, B43_MMIO_GEN_IRQ_REASON); 2658 if (tmp == B43_IRQ_MAC_SUSPENDED) 2659 break; 2660 i++; 2661 if (i >= 20) { 2662 b43err(dev->wl, "Microcode not responding\n"); 2663 b43_print_fw_helptext(dev->wl, 1); 2664 err = -ENODEV; 2665 goto error; 2666 } 2667 msleep(50); 2668 } 2669 b43_read32(dev, B43_MMIO_GEN_IRQ_REASON); /* dummy read */ 2670 2671 /* Get and check the revisions. */ 2672 fwrev = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_UCODEREV); 2673 fwpatch = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_UCODEPATCH); 2674 fwdate = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_UCODEDATE); 2675 fwtime = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_UCODETIME); 2676 2677 if (fwrev <= 0x128) { 2678 b43err(dev->wl, "YOUR FIRMWARE IS TOO OLD. Firmware from " 2679 "binary drivers older than version 4.x is unsupported. " 2680 "You must upgrade your firmware files.\n"); 2681 b43_print_fw_helptext(dev->wl, 1); 2682 err = -EOPNOTSUPP; 2683 goto error; 2684 } 2685 dev->fw.rev = fwrev; 2686 dev->fw.patch = fwpatch; 2687 if (dev->fw.rev >= 598) 2688 dev->fw.hdr_format = B43_FW_HDR_598; 2689 else if (dev->fw.rev >= 410) 2690 dev->fw.hdr_format = B43_FW_HDR_410; 2691 else 2692 dev->fw.hdr_format = B43_FW_HDR_351; 2693 WARN_ON(dev->fw.opensource != (fwdate == 0xFFFF)); 2694 2695 dev->qos_enabled = dev->wl->hw->queues > 1; 2696 /* Default to firmware/hardware crypto acceleration. */ 2697 dev->hwcrypto_enabled = true; 2698 2699 if (dev->fw.opensource) { 2700 u16 fwcapa; 2701 2702 /* Patchlevel info is encoded in the "time" field. */ 2703 dev->fw.patch = fwtime; 2704 b43info(dev->wl, "Loading OpenSource firmware version %u.%u\n", 2705 dev->fw.rev, dev->fw.patch); 2706 2707 fwcapa = b43_fwcapa_read(dev); 2708 if (!(fwcapa & B43_FWCAPA_HWCRYPTO) || dev->fw.pcm_request_failed) { 2709 b43info(dev->wl, "Hardware crypto acceleration not supported by firmware\n"); 2710 /* Disable hardware crypto and fall back to software crypto. */ 2711 dev->hwcrypto_enabled = false; 2712 } 2713 /* adding QoS support should use an offline discovery mechanism */ 2714 WARN(fwcapa & B43_FWCAPA_QOS, "QoS in OpenFW not supported\n"); 2715 } else { 2716 b43info(dev->wl, "Loading firmware version %u.%u " 2717 "(20%.2i-%.2i-%.2i %.2i:%.2i:%.2i)\n", 2718 fwrev, fwpatch, 2719 (fwdate >> 12) & 0xF, (fwdate >> 8) & 0xF, fwdate & 0xFF, 2720 (fwtime >> 11) & 0x1F, (fwtime >> 5) & 0x3F, fwtime & 0x1F); 2721 if (dev->fw.pcm_request_failed) { 2722 b43warn(dev->wl, "No \"pcm5.fw\" firmware file found. " 2723 "Hardware accelerated cryptography is disabled.\n"); 2724 b43_print_fw_helptext(dev->wl, 0); 2725 } 2726 } 2727 2728 snprintf(wiphy->fw_version, sizeof(wiphy->fw_version), "%u.%u", 2729 dev->fw.rev, dev->fw.patch); 2730 wiphy->hw_version = dev->dev->core_id; 2731 2732 if (dev->fw.hdr_format == B43_FW_HDR_351) { 2733 /* We're over the deadline, but we keep support for old fw 2734 * until it turns out to be in major conflict with something new. */ 2735 b43warn(dev->wl, "You are using an old firmware image. " 2736 "Support for old firmware will be removed soon " 2737 "(official deadline was July 2008).\n"); 2738 b43_print_fw_helptext(dev->wl, 0); 2739 } 2740 2741 return 0; 2742 2743 error: 2744 /* Stop the microcode PSM. */ 2745 b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_PSM_RUN, 2746 B43_MACCTL_PSM_JMP0); 2747 2748 return err; 2749 } 2750 2751 static int b43_write_initvals(struct b43_wldev *dev, 2752 const struct b43_iv *ivals, 2753 size_t count, 2754 size_t array_size) 2755 { 2756 const struct b43_iv *iv; 2757 u16 offset; 2758 size_t i; 2759 bool bit32; 2760 2761 BUILD_BUG_ON(sizeof(struct b43_iv) != 6); 2762 iv = ivals; 2763 for (i = 0; i < count; i++) { 2764 if (array_size < sizeof(iv->offset_size)) 2765 goto err_format; 2766 array_size -= sizeof(iv->offset_size); 2767 offset = be16_to_cpu(iv->offset_size); 2768 bit32 = !!(offset & B43_IV_32BIT); 2769 offset &= B43_IV_OFFSET_MASK; 2770 if (offset >= 0x1000) 2771 goto err_format; 2772 if (bit32) { 2773 u32 value; 2774 2775 if (array_size < sizeof(iv->data.d32)) 2776 goto err_format; 2777 array_size -= sizeof(iv->data.d32); 2778 2779 value = get_unaligned_be32(&iv->data.d32); 2780 b43_write32(dev, offset, value); 2781 2782 iv = (const struct b43_iv *)((const uint8_t *)iv + 2783 sizeof(__be16) + 2784 sizeof(__be32)); 2785 } else { 2786 u16 value; 2787 2788 if (array_size < sizeof(iv->data.d16)) 2789 goto err_format; 2790 array_size -= sizeof(iv->data.d16); 2791 2792 value = be16_to_cpu(iv->data.d16); 2793 b43_write16(dev, offset, value); 2794 2795 iv = (const struct b43_iv *)((const uint8_t *)iv + 2796 sizeof(__be16) + 2797 sizeof(__be16)); 2798 } 2799 } 2800 if (array_size) 2801 goto err_format; 2802 2803 return 0; 2804 2805 err_format: 2806 b43err(dev->wl, "Initial Values Firmware file-format error.\n"); 2807 b43_print_fw_helptext(dev->wl, 1); 2808 2809 return -EPROTO; 2810 } 2811 2812 static int b43_upload_initvals(struct b43_wldev *dev) 2813 { 2814 const size_t hdr_len = sizeof(struct b43_fw_header); 2815 const struct b43_fw_header *hdr; 2816 struct b43_firmware *fw = &dev->fw; 2817 const struct b43_iv *ivals; 2818 size_t count; 2819 2820 hdr = (const struct b43_fw_header *)(fw->initvals.data->data); 2821 ivals = (const struct b43_iv *)(fw->initvals.data->data + hdr_len); 2822 count = be32_to_cpu(hdr->size); 2823 return b43_write_initvals(dev, ivals, count, 2824 fw->initvals.data->size - hdr_len); 2825 } 2826 2827 static int b43_upload_initvals_band(struct b43_wldev *dev) 2828 { 2829 const size_t hdr_len = sizeof(struct b43_fw_header); 2830 const struct b43_fw_header *hdr; 2831 struct b43_firmware *fw = &dev->fw; 2832 const struct b43_iv *ivals; 2833 size_t count; 2834 2835 if (!fw->initvals_band.data) 2836 return 0; 2837 2838 hdr = (const struct b43_fw_header *)(fw->initvals_band.data->data); 2839 ivals = (const struct b43_iv *)(fw->initvals_band.data->data + hdr_len); 2840 count = be32_to_cpu(hdr->size); 2841 return b43_write_initvals(dev, ivals, count, 2842 fw->initvals_band.data->size - hdr_len); 2843 } 2844 2845 /* Initialize the GPIOs 2846 * http://bcm-specs.sipsolutions.net/GPIO 2847 */ 2848 2849 #ifdef CONFIG_B43_SSB 2850 static struct ssb_device *b43_ssb_gpio_dev(struct b43_wldev *dev) 2851 { 2852 struct ssb_bus *bus = dev->dev->sdev->bus; 2853 2854 #ifdef CONFIG_SSB_DRIVER_PCICORE 2855 return (bus->chipco.dev ? bus->chipco.dev : bus->pcicore.dev); 2856 #else 2857 return bus->chipco.dev; 2858 #endif 2859 } 2860 #endif 2861 2862 static int b43_gpio_init(struct b43_wldev *dev) 2863 { 2864 #ifdef CONFIG_B43_SSB 2865 struct ssb_device *gpiodev; 2866 #endif 2867 u32 mask, set; 2868 2869 b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_GPOUTSMSK, 0); 2870 b43_maskset16(dev, B43_MMIO_GPIO_MASK, ~0, 0xF); 2871 2872 mask = 0x0000001F; 2873 set = 0x0000000F; 2874 if (dev->dev->chip_id == 0x4301) { 2875 mask |= 0x0060; 2876 set |= 0x0060; 2877 } else if (dev->dev->chip_id == 0x5354) { 2878 /* Don't allow overtaking buttons GPIOs */ 2879 set &= 0x2; /* 0x2 is LED GPIO on BCM5354 */ 2880 } 2881 2882 if (0 /* FIXME: conditional unknown */ ) { 2883 b43_write16(dev, B43_MMIO_GPIO_MASK, 2884 b43_read16(dev, B43_MMIO_GPIO_MASK) 2885 | 0x0100); 2886 /* BT Coexistance Input */ 2887 mask |= 0x0080; 2888 set |= 0x0080; 2889 /* BT Coexistance Out */ 2890 mask |= 0x0100; 2891 set |= 0x0100; 2892 } 2893 if (dev->dev->bus_sprom->boardflags_lo & B43_BFL_PACTRL) { 2894 /* PA is controlled by gpio 9, let ucode handle it */ 2895 b43_write16(dev, B43_MMIO_GPIO_MASK, 2896 b43_read16(dev, B43_MMIO_GPIO_MASK) 2897 | 0x0200); 2898 mask |= 0x0200; 2899 set |= 0x0200; 2900 } 2901 2902 switch (dev->dev->bus_type) { 2903 #ifdef CONFIG_B43_BCMA 2904 case B43_BUS_BCMA: 2905 bcma_chipco_gpio_control(&dev->dev->bdev->bus->drv_cc, mask, set); 2906 break; 2907 #endif 2908 #ifdef CONFIG_B43_SSB 2909 case B43_BUS_SSB: 2910 gpiodev = b43_ssb_gpio_dev(dev); 2911 if (gpiodev) 2912 ssb_write32(gpiodev, B43_GPIO_CONTROL, 2913 (ssb_read32(gpiodev, B43_GPIO_CONTROL) 2914 & ~mask) | set); 2915 break; 2916 #endif 2917 } 2918 2919 return 0; 2920 } 2921 2922 /* Turn off all GPIO stuff. Call this on module unload, for example. */ 2923 static void b43_gpio_cleanup(struct b43_wldev *dev) 2924 { 2925 #ifdef CONFIG_B43_SSB 2926 struct ssb_device *gpiodev; 2927 #endif 2928 2929 switch (dev->dev->bus_type) { 2930 #ifdef CONFIG_B43_BCMA 2931 case B43_BUS_BCMA: 2932 bcma_chipco_gpio_control(&dev->dev->bdev->bus->drv_cc, ~0, 0); 2933 break; 2934 #endif 2935 #ifdef CONFIG_B43_SSB 2936 case B43_BUS_SSB: 2937 gpiodev = b43_ssb_gpio_dev(dev); 2938 if (gpiodev) 2939 ssb_write32(gpiodev, B43_GPIO_CONTROL, 0); 2940 break; 2941 #endif 2942 } 2943 } 2944 2945 /* http://bcm-specs.sipsolutions.net/EnableMac */ 2946 void b43_mac_enable(struct b43_wldev *dev) 2947 { 2948 if (b43_debug(dev, B43_DBG_FIRMWARE)) { 2949 u16 fwstate; 2950 2951 fwstate = b43_shm_read16(dev, B43_SHM_SHARED, 2952 B43_SHM_SH_UCODESTAT); 2953 if ((fwstate != B43_SHM_SH_UCODESTAT_SUSP) && 2954 (fwstate != B43_SHM_SH_UCODESTAT_SLEEP)) { 2955 b43err(dev->wl, "b43_mac_enable(): The firmware " 2956 "should be suspended, but current state is %u\n", 2957 fwstate); 2958 } 2959 } 2960 2961 dev->mac_suspended--; 2962 B43_WARN_ON(dev->mac_suspended < 0); 2963 if (dev->mac_suspended == 0) { 2964 b43_maskset32(dev, B43_MMIO_MACCTL, ~0, B43_MACCTL_ENABLED); 2965 b43_write32(dev, B43_MMIO_GEN_IRQ_REASON, 2966 B43_IRQ_MAC_SUSPENDED); 2967 /* Commit writes */ 2968 b43_read32(dev, B43_MMIO_MACCTL); 2969 b43_read32(dev, B43_MMIO_GEN_IRQ_REASON); 2970 b43_power_saving_ctl_bits(dev, 0); 2971 } 2972 } 2973 2974 /* http://bcm-specs.sipsolutions.net/SuspendMAC */ 2975 void b43_mac_suspend(struct b43_wldev *dev) 2976 { 2977 int i; 2978 u32 tmp; 2979 2980 might_sleep(); 2981 B43_WARN_ON(dev->mac_suspended < 0); 2982 2983 if (dev->mac_suspended == 0) { 2984 b43_power_saving_ctl_bits(dev, B43_PS_AWAKE); 2985 b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_ENABLED, 0); 2986 /* force pci to flush the write */ 2987 b43_read32(dev, B43_MMIO_MACCTL); 2988 for (i = 35; i; i--) { 2989 tmp = b43_read32(dev, B43_MMIO_GEN_IRQ_REASON); 2990 if (tmp & B43_IRQ_MAC_SUSPENDED) 2991 goto out; 2992 udelay(10); 2993 } 2994 /* Hm, it seems this will take some time. Use msleep(). */ 2995 for (i = 40; i; i--) { 2996 tmp = b43_read32(dev, B43_MMIO_GEN_IRQ_REASON); 2997 if (tmp & B43_IRQ_MAC_SUSPENDED) 2998 goto out; 2999 msleep(1); 3000 } 3001 b43err(dev->wl, "MAC suspend failed\n"); 3002 } 3003 out: 3004 dev->mac_suspended++; 3005 } 3006 3007 /* http://bcm-v4.sipsolutions.net/802.11/PHY/N/MacPhyClkSet */ 3008 void b43_mac_phy_clock_set(struct b43_wldev *dev, bool on) 3009 { 3010 u32 tmp; 3011 3012 switch (dev->dev->bus_type) { 3013 #ifdef CONFIG_B43_BCMA 3014 case B43_BUS_BCMA: 3015 tmp = bcma_aread32(dev->dev->bdev, BCMA_IOCTL); 3016 if (on) 3017 tmp |= B43_BCMA_IOCTL_MACPHYCLKEN; 3018 else 3019 tmp &= ~B43_BCMA_IOCTL_MACPHYCLKEN; 3020 bcma_awrite32(dev->dev->bdev, BCMA_IOCTL, tmp); 3021 break; 3022 #endif 3023 #ifdef CONFIG_B43_SSB 3024 case B43_BUS_SSB: 3025 tmp = ssb_read32(dev->dev->sdev, SSB_TMSLOW); 3026 if (on) 3027 tmp |= B43_TMSLOW_MACPHYCLKEN; 3028 else 3029 tmp &= ~B43_TMSLOW_MACPHYCLKEN; 3030 ssb_write32(dev->dev->sdev, SSB_TMSLOW, tmp); 3031 break; 3032 #endif 3033 } 3034 } 3035 3036 /* brcms_b_switch_macfreq */ 3037 void b43_mac_switch_freq(struct b43_wldev *dev, u8 spurmode) 3038 { 3039 u16 chip_id = dev->dev->chip_id; 3040 3041 if (chip_id == BCMA_CHIP_ID_BCM4331) { 3042 switch (spurmode) { 3043 case 2: /* 168 Mhz: 2^26/168 = 0x61862 */ 3044 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0x1862); 3045 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0x6); 3046 break; 3047 case 1: /* 164 Mhz: 2^26/164 = 0x63e70 */ 3048 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0x3e70); 3049 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0x6); 3050 break; 3051 default: /* 160 Mhz: 2^26/160 = 0x66666 */ 3052 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0x6666); 3053 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0x6); 3054 break; 3055 } 3056 } else if (chip_id == BCMA_CHIP_ID_BCM43131 || 3057 chip_id == BCMA_CHIP_ID_BCM43217 || 3058 chip_id == BCMA_CHIP_ID_BCM43222 || 3059 chip_id == BCMA_CHIP_ID_BCM43224 || 3060 chip_id == BCMA_CHIP_ID_BCM43225 || 3061 chip_id == BCMA_CHIP_ID_BCM43227 || 3062 chip_id == BCMA_CHIP_ID_BCM43228) { 3063 switch (spurmode) { 3064 case 2: /* 126 Mhz */ 3065 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0x2082); 3066 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0x8); 3067 break; 3068 case 1: /* 123 Mhz */ 3069 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0x5341); 3070 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0x8); 3071 break; 3072 default: /* 120 Mhz */ 3073 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0x8889); 3074 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0x8); 3075 break; 3076 } 3077 } else if (dev->phy.type == B43_PHYTYPE_LCN) { 3078 switch (spurmode) { 3079 case 1: /* 82 Mhz */ 3080 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0x7CE0); 3081 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0xC); 3082 break; 3083 default: /* 80 Mhz */ 3084 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0xCCCD); 3085 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0xC); 3086 break; 3087 } 3088 } 3089 } 3090 3091 static void b43_adjust_opmode(struct b43_wldev *dev) 3092 { 3093 struct b43_wl *wl = dev->wl; 3094 u32 ctl; 3095 u16 cfp_pretbtt; 3096 3097 ctl = b43_read32(dev, B43_MMIO_MACCTL); 3098 /* Reset status to STA infrastructure mode. */ 3099 ctl &= ~B43_MACCTL_AP; 3100 ctl &= ~B43_MACCTL_KEEP_CTL; 3101 ctl &= ~B43_MACCTL_KEEP_BADPLCP; 3102 ctl &= ~B43_MACCTL_KEEP_BAD; 3103 ctl &= ~B43_MACCTL_PROMISC; 3104 ctl &= ~B43_MACCTL_BEACPROMISC; 3105 ctl |= B43_MACCTL_INFRA; 3106 3107 if (b43_is_mode(wl, NL80211_IFTYPE_AP) || 3108 b43_is_mode(wl, NL80211_IFTYPE_MESH_POINT)) 3109 ctl |= B43_MACCTL_AP; 3110 else if (b43_is_mode(wl, NL80211_IFTYPE_ADHOC)) 3111 ctl &= ~B43_MACCTL_INFRA; 3112 3113 if (wl->filter_flags & FIF_CONTROL) 3114 ctl |= B43_MACCTL_KEEP_CTL; 3115 if (wl->filter_flags & FIF_FCSFAIL) 3116 ctl |= B43_MACCTL_KEEP_BAD; 3117 if (wl->filter_flags & FIF_PLCPFAIL) 3118 ctl |= B43_MACCTL_KEEP_BADPLCP; 3119 if (wl->filter_flags & FIF_BCN_PRBRESP_PROMISC) 3120 ctl |= B43_MACCTL_BEACPROMISC; 3121 3122 /* Workaround: On old hardware the HW-MAC-address-filter 3123 * doesn't work properly, so always run promisc in filter 3124 * it in software. */ 3125 if (dev->dev->core_rev <= 4) 3126 ctl |= B43_MACCTL_PROMISC; 3127 3128 b43_write32(dev, B43_MMIO_MACCTL, ctl); 3129 3130 cfp_pretbtt = 2; 3131 if ((ctl & B43_MACCTL_INFRA) && !(ctl & B43_MACCTL_AP)) { 3132 if (dev->dev->chip_id == 0x4306 && 3133 dev->dev->chip_rev == 3) 3134 cfp_pretbtt = 100; 3135 else 3136 cfp_pretbtt = 50; 3137 } 3138 b43_write16(dev, 0x612, cfp_pretbtt); 3139 3140 /* FIXME: We don't currently implement the PMQ mechanism, 3141 * so always disable it. If we want to implement PMQ, 3142 * we need to enable it here (clear DISCPMQ) in AP mode. 3143 */ 3144 if (0 /* ctl & B43_MACCTL_AP */) 3145 b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_DISCPMQ, 0); 3146 else 3147 b43_maskset32(dev, B43_MMIO_MACCTL, ~0, B43_MACCTL_DISCPMQ); 3148 } 3149 3150 static void b43_rate_memory_write(struct b43_wldev *dev, u16 rate, int is_ofdm) 3151 { 3152 u16 offset; 3153 3154 if (is_ofdm) { 3155 offset = 0x480; 3156 offset += (b43_plcp_get_ratecode_ofdm(rate) & 0x000F) * 2; 3157 } else { 3158 offset = 0x4C0; 3159 offset += (b43_plcp_get_ratecode_cck(rate) & 0x000F) * 2; 3160 } 3161 b43_shm_write16(dev, B43_SHM_SHARED, offset + 0x20, 3162 b43_shm_read16(dev, B43_SHM_SHARED, offset)); 3163 } 3164 3165 static void b43_rate_memory_init(struct b43_wldev *dev) 3166 { 3167 switch (dev->phy.type) { 3168 case B43_PHYTYPE_G: 3169 case B43_PHYTYPE_N: 3170 case B43_PHYTYPE_LP: 3171 case B43_PHYTYPE_HT: 3172 case B43_PHYTYPE_LCN: 3173 b43_rate_memory_write(dev, B43_OFDM_RATE_6MB, 1); 3174 b43_rate_memory_write(dev, B43_OFDM_RATE_9MB, 1); 3175 b43_rate_memory_write(dev, B43_OFDM_RATE_12MB, 1); 3176 b43_rate_memory_write(dev, B43_OFDM_RATE_18MB, 1); 3177 b43_rate_memory_write(dev, B43_OFDM_RATE_24MB, 1); 3178 b43_rate_memory_write(dev, B43_OFDM_RATE_36MB, 1); 3179 b43_rate_memory_write(dev, B43_OFDM_RATE_48MB, 1); 3180 b43_rate_memory_write(dev, B43_OFDM_RATE_54MB, 1); 3181 /* fallthrough */ 3182 case B43_PHYTYPE_B: 3183 b43_rate_memory_write(dev, B43_CCK_RATE_1MB, 0); 3184 b43_rate_memory_write(dev, B43_CCK_RATE_2MB, 0); 3185 b43_rate_memory_write(dev, B43_CCK_RATE_5MB, 0); 3186 b43_rate_memory_write(dev, B43_CCK_RATE_11MB, 0); 3187 break; 3188 default: 3189 B43_WARN_ON(1); 3190 } 3191 } 3192 3193 /* Set the default values for the PHY TX Control Words. */ 3194 static void b43_set_phytxctl_defaults(struct b43_wldev *dev) 3195 { 3196 u16 ctl = 0; 3197 3198 ctl |= B43_TXH_PHY_ENC_CCK; 3199 ctl |= B43_TXH_PHY_ANT01AUTO; 3200 ctl |= B43_TXH_PHY_TXPWR; 3201 3202 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_BEACPHYCTL, ctl); 3203 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_ACKCTSPHYCTL, ctl); 3204 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_PRPHYCTL, ctl); 3205 } 3206 3207 /* Set the TX-Antenna for management frames sent by firmware. */ 3208 static void b43_mgmtframe_txantenna(struct b43_wldev *dev, int antenna) 3209 { 3210 u16 ant; 3211 u16 tmp; 3212 3213 ant = b43_antenna_to_phyctl(antenna); 3214 3215 /* For ACK/CTS */ 3216 tmp = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_ACKCTSPHYCTL); 3217 tmp = (tmp & ~B43_TXH_PHY_ANT) | ant; 3218 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_ACKCTSPHYCTL, tmp); 3219 /* For Probe Resposes */ 3220 tmp = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_PRPHYCTL); 3221 tmp = (tmp & ~B43_TXH_PHY_ANT) | ant; 3222 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_PRPHYCTL, tmp); 3223 } 3224 3225 /* This is the opposite of b43_chip_init() */ 3226 static void b43_chip_exit(struct b43_wldev *dev) 3227 { 3228 b43_phy_exit(dev); 3229 b43_gpio_cleanup(dev); 3230 /* firmware is released later */ 3231 } 3232 3233 /* Initialize the chip 3234 * http://bcm-specs.sipsolutions.net/ChipInit 3235 */ 3236 static int b43_chip_init(struct b43_wldev *dev) 3237 { 3238 struct b43_phy *phy = &dev->phy; 3239 int err; 3240 u32 macctl; 3241 u16 value16; 3242 3243 /* Initialize the MAC control */ 3244 macctl = B43_MACCTL_IHR_ENABLED | B43_MACCTL_SHM_ENABLED; 3245 if (dev->phy.gmode) 3246 macctl |= B43_MACCTL_GMODE; 3247 macctl |= B43_MACCTL_INFRA; 3248 b43_write32(dev, B43_MMIO_MACCTL, macctl); 3249 3250 err = b43_upload_microcode(dev); 3251 if (err) 3252 goto out; /* firmware is released later */ 3253 3254 err = b43_gpio_init(dev); 3255 if (err) 3256 goto out; /* firmware is released later */ 3257 3258 err = b43_upload_initvals(dev); 3259 if (err) 3260 goto err_gpio_clean; 3261 3262 err = b43_upload_initvals_band(dev); 3263 if (err) 3264 goto err_gpio_clean; 3265 3266 /* Turn the Analog on and initialize the PHY. */ 3267 phy->ops->switch_analog(dev, 1); 3268 err = b43_phy_init(dev); 3269 if (err) 3270 goto err_gpio_clean; 3271 3272 /* Disable Interference Mitigation. */ 3273 if (phy->ops->interf_mitigation) 3274 phy->ops->interf_mitigation(dev, B43_INTERFMODE_NONE); 3275 3276 /* Select the antennae */ 3277 if (phy->ops->set_rx_antenna) 3278 phy->ops->set_rx_antenna(dev, B43_ANTENNA_DEFAULT); 3279 b43_mgmtframe_txantenna(dev, B43_ANTENNA_DEFAULT); 3280 3281 if (phy->type == B43_PHYTYPE_B) { 3282 value16 = b43_read16(dev, 0x005E); 3283 value16 |= 0x0004; 3284 b43_write16(dev, 0x005E, value16); 3285 } 3286 b43_write32(dev, 0x0100, 0x01000000); 3287 if (dev->dev->core_rev < 5) 3288 b43_write32(dev, 0x010C, 0x01000000); 3289 3290 b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_INFRA, 0); 3291 b43_maskset32(dev, B43_MMIO_MACCTL, ~0, B43_MACCTL_INFRA); 3292 3293 /* Probe Response Timeout value */ 3294 /* FIXME: Default to 0, has to be set by ioctl probably... :-/ */ 3295 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_PRMAXTIME, 0); 3296 3297 /* Initially set the wireless operation mode. */ 3298 b43_adjust_opmode(dev); 3299 3300 if (dev->dev->core_rev < 3) { 3301 b43_write16(dev, 0x060E, 0x0000); 3302 b43_write16(dev, 0x0610, 0x8000); 3303 b43_write16(dev, 0x0604, 0x0000); 3304 b43_write16(dev, 0x0606, 0x0200); 3305 } else { 3306 b43_write32(dev, 0x0188, 0x80000000); 3307 b43_write32(dev, 0x018C, 0x02000000); 3308 } 3309 b43_write32(dev, B43_MMIO_GEN_IRQ_REASON, 0x00004000); 3310 b43_write32(dev, B43_MMIO_DMA0_IRQ_MASK, 0x0001FC00); 3311 b43_write32(dev, B43_MMIO_DMA1_IRQ_MASK, 0x0000DC00); 3312 b43_write32(dev, B43_MMIO_DMA2_IRQ_MASK, 0x0000DC00); 3313 b43_write32(dev, B43_MMIO_DMA3_IRQ_MASK, 0x0001DC00); 3314 b43_write32(dev, B43_MMIO_DMA4_IRQ_MASK, 0x0000DC00); 3315 b43_write32(dev, B43_MMIO_DMA5_IRQ_MASK, 0x0000DC00); 3316 3317 b43_mac_phy_clock_set(dev, true); 3318 3319 switch (dev->dev->bus_type) { 3320 #ifdef CONFIG_B43_BCMA 3321 case B43_BUS_BCMA: 3322 /* FIXME: 0xE74 is quite common, but should be read from CC */ 3323 b43_write16(dev, B43_MMIO_POWERUP_DELAY, 0xE74); 3324 break; 3325 #endif 3326 #ifdef CONFIG_B43_SSB 3327 case B43_BUS_SSB: 3328 b43_write16(dev, B43_MMIO_POWERUP_DELAY, 3329 dev->dev->sdev->bus->chipco.fast_pwrup_delay); 3330 break; 3331 #endif 3332 } 3333 3334 err = 0; 3335 b43dbg(dev->wl, "Chip initialized\n"); 3336 out: 3337 return err; 3338 3339 err_gpio_clean: 3340 b43_gpio_cleanup(dev); 3341 return err; 3342 } 3343 3344 static void b43_periodic_every60sec(struct b43_wldev *dev) 3345 { 3346 const struct b43_phy_operations *ops = dev->phy.ops; 3347 3348 if (ops->pwork_60sec) 3349 ops->pwork_60sec(dev); 3350 3351 /* Force check the TX power emission now. */ 3352 b43_phy_txpower_check(dev, B43_TXPWR_IGNORE_TIME); 3353 } 3354 3355 static void b43_periodic_every30sec(struct b43_wldev *dev) 3356 { 3357 /* Update device statistics. */ 3358 b43_calculate_link_quality(dev); 3359 } 3360 3361 static void b43_periodic_every15sec(struct b43_wldev *dev) 3362 { 3363 struct b43_phy *phy = &dev->phy; 3364 u16 wdr; 3365 3366 if (dev->fw.opensource) { 3367 /* Check if the firmware is still alive. 3368 * It will reset the watchdog counter to 0 in its idle loop. */ 3369 wdr = b43_shm_read16(dev, B43_SHM_SCRATCH, B43_WATCHDOG_REG); 3370 if (unlikely(wdr)) { 3371 b43err(dev->wl, "Firmware watchdog: The firmware died!\n"); 3372 b43_controller_restart(dev, "Firmware watchdog"); 3373 return; 3374 } else { 3375 b43_shm_write16(dev, B43_SHM_SCRATCH, 3376 B43_WATCHDOG_REG, 1); 3377 } 3378 } 3379 3380 if (phy->ops->pwork_15sec) 3381 phy->ops->pwork_15sec(dev); 3382 3383 atomic_set(&phy->txerr_cnt, B43_PHY_TX_BADNESS_LIMIT); 3384 wmb(); 3385 3386 #if B43_DEBUG 3387 if (b43_debug(dev, B43_DBG_VERBOSESTATS)) { 3388 unsigned int i; 3389 3390 b43dbg(dev->wl, "Stats: %7u IRQs/sec, %7u TX/sec, %7u RX/sec\n", 3391 dev->irq_count / 15, 3392 dev->tx_count / 15, 3393 dev->rx_count / 15); 3394 dev->irq_count = 0; 3395 dev->tx_count = 0; 3396 dev->rx_count = 0; 3397 for (i = 0; i < ARRAY_SIZE(dev->irq_bit_count); i++) { 3398 if (dev->irq_bit_count[i]) { 3399 b43dbg(dev->wl, "Stats: %7u IRQ-%02u/sec (0x%08X)\n", 3400 dev->irq_bit_count[i] / 15, i, (1 << i)); 3401 dev->irq_bit_count[i] = 0; 3402 } 3403 } 3404 } 3405 #endif 3406 } 3407 3408 static void do_periodic_work(struct b43_wldev *dev) 3409 { 3410 unsigned int state; 3411 3412 state = dev->periodic_state; 3413 if (state % 4 == 0) 3414 b43_periodic_every60sec(dev); 3415 if (state % 2 == 0) 3416 b43_periodic_every30sec(dev); 3417 b43_periodic_every15sec(dev); 3418 } 3419 3420 /* Periodic work locking policy: 3421 * The whole periodic work handler is protected by 3422 * wl->mutex. If another lock is needed somewhere in the 3423 * pwork callchain, it's acquired in-place, where it's needed. 3424 */ 3425 static void b43_periodic_work_handler(struct work_struct *work) 3426 { 3427 struct b43_wldev *dev = container_of(work, struct b43_wldev, 3428 periodic_work.work); 3429 struct b43_wl *wl = dev->wl; 3430 unsigned long delay; 3431 3432 mutex_lock(&wl->mutex); 3433 3434 if (unlikely(b43_status(dev) != B43_STAT_STARTED)) 3435 goto out; 3436 if (b43_debug(dev, B43_DBG_PWORK_STOP)) 3437 goto out_requeue; 3438 3439 do_periodic_work(dev); 3440 3441 dev->periodic_state++; 3442 out_requeue: 3443 if (b43_debug(dev, B43_DBG_PWORK_FAST)) 3444 delay = msecs_to_jiffies(50); 3445 else 3446 delay = round_jiffies_relative(HZ * 15); 3447 ieee80211_queue_delayed_work(wl->hw, &dev->periodic_work, delay); 3448 out: 3449 mutex_unlock(&wl->mutex); 3450 } 3451 3452 static void b43_periodic_tasks_setup(struct b43_wldev *dev) 3453 { 3454 struct delayed_work *work = &dev->periodic_work; 3455 3456 dev->periodic_state = 0; 3457 INIT_DELAYED_WORK(work, b43_periodic_work_handler); 3458 ieee80211_queue_delayed_work(dev->wl->hw, work, 0); 3459 } 3460 3461 /* Check if communication with the device works correctly. */ 3462 static int b43_validate_chipaccess(struct b43_wldev *dev) 3463 { 3464 u32 v, backup0, backup4; 3465 3466 backup0 = b43_shm_read32(dev, B43_SHM_SHARED, 0); 3467 backup4 = b43_shm_read32(dev, B43_SHM_SHARED, 4); 3468 3469 /* Check for read/write and endianness problems. */ 3470 b43_shm_write32(dev, B43_SHM_SHARED, 0, 0x55AAAA55); 3471 if (b43_shm_read32(dev, B43_SHM_SHARED, 0) != 0x55AAAA55) 3472 goto error; 3473 b43_shm_write32(dev, B43_SHM_SHARED, 0, 0xAA5555AA); 3474 if (b43_shm_read32(dev, B43_SHM_SHARED, 0) != 0xAA5555AA) 3475 goto error; 3476 3477 /* Check if unaligned 32bit SHM_SHARED access works properly. 3478 * However, don't bail out on failure, because it's noncritical. */ 3479 b43_shm_write16(dev, B43_SHM_SHARED, 0, 0x1122); 3480 b43_shm_write16(dev, B43_SHM_SHARED, 2, 0x3344); 3481 b43_shm_write16(dev, B43_SHM_SHARED, 4, 0x5566); 3482 b43_shm_write16(dev, B43_SHM_SHARED, 6, 0x7788); 3483 if (b43_shm_read32(dev, B43_SHM_SHARED, 2) != 0x55663344) 3484 b43warn(dev->wl, "Unaligned 32bit SHM read access is broken\n"); 3485 b43_shm_write32(dev, B43_SHM_SHARED, 2, 0xAABBCCDD); 3486 if (b43_shm_read16(dev, B43_SHM_SHARED, 0) != 0x1122 || 3487 b43_shm_read16(dev, B43_SHM_SHARED, 2) != 0xCCDD || 3488 b43_shm_read16(dev, B43_SHM_SHARED, 4) != 0xAABB || 3489 b43_shm_read16(dev, B43_SHM_SHARED, 6) != 0x7788) 3490 b43warn(dev->wl, "Unaligned 32bit SHM write access is broken\n"); 3491 3492 b43_shm_write32(dev, B43_SHM_SHARED, 0, backup0); 3493 b43_shm_write32(dev, B43_SHM_SHARED, 4, backup4); 3494 3495 if ((dev->dev->core_rev >= 3) && (dev->dev->core_rev <= 10)) { 3496 /* The 32bit register shadows the two 16bit registers 3497 * with update sideeffects. Validate this. */ 3498 b43_write16(dev, B43_MMIO_TSF_CFP_START, 0xAAAA); 3499 b43_write32(dev, B43_MMIO_TSF_CFP_START, 0xCCCCBBBB); 3500 if (b43_read16(dev, B43_MMIO_TSF_CFP_START_LOW) != 0xBBBB) 3501 goto error; 3502 if (b43_read16(dev, B43_MMIO_TSF_CFP_START_HIGH) != 0xCCCC) 3503 goto error; 3504 } 3505 b43_write32(dev, B43_MMIO_TSF_CFP_START, 0); 3506 3507 v = b43_read32(dev, B43_MMIO_MACCTL); 3508 v |= B43_MACCTL_GMODE; 3509 if (v != (B43_MACCTL_GMODE | B43_MACCTL_IHR_ENABLED)) 3510 goto error; 3511 3512 return 0; 3513 error: 3514 b43err(dev->wl, "Failed to validate the chipaccess\n"); 3515 return -ENODEV; 3516 } 3517 3518 static void b43_security_init(struct b43_wldev *dev) 3519 { 3520 dev->ktp = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_KTP); 3521 /* KTP is a word address, but we address SHM bytewise. 3522 * So multiply by two. 3523 */ 3524 dev->ktp *= 2; 3525 /* Number of RCMTA address slots */ 3526 b43_write16(dev, B43_MMIO_RCMTA_COUNT, B43_NR_PAIRWISE_KEYS); 3527 /* Clear the key memory. */ 3528 b43_clear_keys(dev); 3529 } 3530 3531 #ifdef CONFIG_B43_HWRNG 3532 static int b43_rng_read(struct hwrng *rng, u32 *data) 3533 { 3534 struct b43_wl *wl = (struct b43_wl *)rng->priv; 3535 struct b43_wldev *dev; 3536 int count = -ENODEV; 3537 3538 mutex_lock(&wl->mutex); 3539 dev = wl->current_dev; 3540 if (likely(dev && b43_status(dev) >= B43_STAT_INITIALIZED)) { 3541 *data = b43_read16(dev, B43_MMIO_RNG); 3542 count = sizeof(u16); 3543 } 3544 mutex_unlock(&wl->mutex); 3545 3546 return count; 3547 } 3548 #endif /* CONFIG_B43_HWRNG */ 3549 3550 static void b43_rng_exit(struct b43_wl *wl) 3551 { 3552 #ifdef CONFIG_B43_HWRNG 3553 if (wl->rng_initialized) 3554 hwrng_unregister(&wl->rng); 3555 #endif /* CONFIG_B43_HWRNG */ 3556 } 3557 3558 static int b43_rng_init(struct b43_wl *wl) 3559 { 3560 int err = 0; 3561 3562 #ifdef CONFIG_B43_HWRNG 3563 snprintf(wl->rng_name, ARRAY_SIZE(wl->rng_name), 3564 "%s_%s", KBUILD_MODNAME, wiphy_name(wl->hw->wiphy)); 3565 wl->rng.name = wl->rng_name; 3566 wl->rng.data_read = b43_rng_read; 3567 wl->rng.priv = (unsigned long)wl; 3568 wl->rng_initialized = true; 3569 err = hwrng_register(&wl->rng); 3570 if (err) { 3571 wl->rng_initialized = false; 3572 b43err(wl, "Failed to register the random " 3573 "number generator (%d)\n", err); 3574 } 3575 #endif /* CONFIG_B43_HWRNG */ 3576 3577 return err; 3578 } 3579 3580 static void b43_tx_work(struct work_struct *work) 3581 { 3582 struct b43_wl *wl = container_of(work, struct b43_wl, tx_work); 3583 struct b43_wldev *dev; 3584 struct sk_buff *skb; 3585 int queue_num; 3586 int err = 0; 3587 3588 mutex_lock(&wl->mutex); 3589 dev = wl->current_dev; 3590 if (unlikely(!dev || b43_status(dev) < B43_STAT_STARTED)) { 3591 mutex_unlock(&wl->mutex); 3592 return; 3593 } 3594 3595 for (queue_num = 0; queue_num < B43_QOS_QUEUE_NUM; queue_num++) { 3596 while (skb_queue_len(&wl->tx_queue[queue_num])) { 3597 skb = skb_dequeue(&wl->tx_queue[queue_num]); 3598 if (b43_using_pio_transfers(dev)) 3599 err = b43_pio_tx(dev, skb); 3600 else 3601 err = b43_dma_tx(dev, skb); 3602 if (err == -ENOSPC) { 3603 wl->tx_queue_stopped[queue_num] = true; 3604 ieee80211_stop_queue(wl->hw, queue_num); 3605 skb_queue_head(&wl->tx_queue[queue_num], skb); 3606 break; 3607 } 3608 if (unlikely(err)) 3609 ieee80211_free_txskb(wl->hw, skb); 3610 err = 0; 3611 } 3612 3613 if (!err) 3614 wl->tx_queue_stopped[queue_num] = false; 3615 } 3616 3617 #if B43_DEBUG 3618 dev->tx_count++; 3619 #endif 3620 mutex_unlock(&wl->mutex); 3621 } 3622 3623 static void b43_op_tx(struct ieee80211_hw *hw, 3624 struct ieee80211_tx_control *control, 3625 struct sk_buff *skb) 3626 { 3627 struct b43_wl *wl = hw_to_b43_wl(hw); 3628 3629 if (unlikely(skb->len < 2 + 2 + 6)) { 3630 /* Too short, this can't be a valid frame. */ 3631 ieee80211_free_txskb(hw, skb); 3632 return; 3633 } 3634 B43_WARN_ON(skb_shinfo(skb)->nr_frags); 3635 3636 skb_queue_tail(&wl->tx_queue[skb->queue_mapping], skb); 3637 if (!wl->tx_queue_stopped[skb->queue_mapping]) { 3638 ieee80211_queue_work(wl->hw, &wl->tx_work); 3639 } else { 3640 ieee80211_stop_queue(wl->hw, skb->queue_mapping); 3641 } 3642 } 3643 3644 static void b43_qos_params_upload(struct b43_wldev *dev, 3645 const struct ieee80211_tx_queue_params *p, 3646 u16 shm_offset) 3647 { 3648 u16 params[B43_NR_QOSPARAMS]; 3649 int bslots, tmp; 3650 unsigned int i; 3651 3652 if (!dev->qos_enabled) 3653 return; 3654 3655 bslots = b43_read16(dev, B43_MMIO_RNG) & p->cw_min; 3656 3657 memset(¶ms, 0, sizeof(params)); 3658 3659 params[B43_QOSPARAM_TXOP] = p->txop * 32; 3660 params[B43_QOSPARAM_CWMIN] = p->cw_min; 3661 params[B43_QOSPARAM_CWMAX] = p->cw_max; 3662 params[B43_QOSPARAM_CWCUR] = p->cw_min; 3663 params[B43_QOSPARAM_AIFS] = p->aifs; 3664 params[B43_QOSPARAM_BSLOTS] = bslots; 3665 params[B43_QOSPARAM_REGGAP] = bslots + p->aifs; 3666 3667 for (i = 0; i < ARRAY_SIZE(params); i++) { 3668 if (i == B43_QOSPARAM_STATUS) { 3669 tmp = b43_shm_read16(dev, B43_SHM_SHARED, 3670 shm_offset + (i * 2)); 3671 /* Mark the parameters as updated. */ 3672 tmp |= 0x100; 3673 b43_shm_write16(dev, B43_SHM_SHARED, 3674 shm_offset + (i * 2), 3675 tmp); 3676 } else { 3677 b43_shm_write16(dev, B43_SHM_SHARED, 3678 shm_offset + (i * 2), 3679 params[i]); 3680 } 3681 } 3682 } 3683 3684 /* Mapping of mac80211 queue numbers to b43 QoS SHM offsets. */ 3685 static const u16 b43_qos_shm_offsets[] = { 3686 /* [mac80211-queue-nr] = SHM_OFFSET, */ 3687 [0] = B43_QOS_VOICE, 3688 [1] = B43_QOS_VIDEO, 3689 [2] = B43_QOS_BESTEFFORT, 3690 [3] = B43_QOS_BACKGROUND, 3691 }; 3692 3693 /* Update all QOS parameters in hardware. */ 3694 static void b43_qos_upload_all(struct b43_wldev *dev) 3695 { 3696 struct b43_wl *wl = dev->wl; 3697 struct b43_qos_params *params; 3698 unsigned int i; 3699 3700 if (!dev->qos_enabled) 3701 return; 3702 3703 BUILD_BUG_ON(ARRAY_SIZE(b43_qos_shm_offsets) != 3704 ARRAY_SIZE(wl->qos_params)); 3705 3706 b43_mac_suspend(dev); 3707 for (i = 0; i < ARRAY_SIZE(wl->qos_params); i++) { 3708 params = &(wl->qos_params[i]); 3709 b43_qos_params_upload(dev, &(params->p), 3710 b43_qos_shm_offsets[i]); 3711 } 3712 b43_mac_enable(dev); 3713 } 3714 3715 static void b43_qos_clear(struct b43_wl *wl) 3716 { 3717 struct b43_qos_params *params; 3718 unsigned int i; 3719 3720 /* Initialize QoS parameters to sane defaults. */ 3721 3722 BUILD_BUG_ON(ARRAY_SIZE(b43_qos_shm_offsets) != 3723 ARRAY_SIZE(wl->qos_params)); 3724 3725 for (i = 0; i < ARRAY_SIZE(wl->qos_params); i++) { 3726 params = &(wl->qos_params[i]); 3727 3728 switch (b43_qos_shm_offsets[i]) { 3729 case B43_QOS_VOICE: 3730 params->p.txop = 0; 3731 params->p.aifs = 2; 3732 params->p.cw_min = 0x0001; 3733 params->p.cw_max = 0x0001; 3734 break; 3735 case B43_QOS_VIDEO: 3736 params->p.txop = 0; 3737 params->p.aifs = 2; 3738 params->p.cw_min = 0x0001; 3739 params->p.cw_max = 0x0001; 3740 break; 3741 case B43_QOS_BESTEFFORT: 3742 params->p.txop = 0; 3743 params->p.aifs = 3; 3744 params->p.cw_min = 0x0001; 3745 params->p.cw_max = 0x03FF; 3746 break; 3747 case B43_QOS_BACKGROUND: 3748 params->p.txop = 0; 3749 params->p.aifs = 7; 3750 params->p.cw_min = 0x0001; 3751 params->p.cw_max = 0x03FF; 3752 break; 3753 default: 3754 B43_WARN_ON(1); 3755 } 3756 } 3757 } 3758 3759 /* Initialize the core's QOS capabilities */ 3760 static void b43_qos_init(struct b43_wldev *dev) 3761 { 3762 if (!dev->qos_enabled) { 3763 /* Disable QOS support. */ 3764 b43_hf_write(dev, b43_hf_read(dev) & ~B43_HF_EDCF); 3765 b43_write16(dev, B43_MMIO_IFSCTL, 3766 b43_read16(dev, B43_MMIO_IFSCTL) 3767 & ~B43_MMIO_IFSCTL_USE_EDCF); 3768 b43dbg(dev->wl, "QoS disabled\n"); 3769 return; 3770 } 3771 3772 /* Upload the current QOS parameters. */ 3773 b43_qos_upload_all(dev); 3774 3775 /* Enable QOS support. */ 3776 b43_hf_write(dev, b43_hf_read(dev) | B43_HF_EDCF); 3777 b43_write16(dev, B43_MMIO_IFSCTL, 3778 b43_read16(dev, B43_MMIO_IFSCTL) 3779 | B43_MMIO_IFSCTL_USE_EDCF); 3780 b43dbg(dev->wl, "QoS enabled\n"); 3781 } 3782 3783 static int b43_op_conf_tx(struct ieee80211_hw *hw, 3784 struct ieee80211_vif *vif, u16 _queue, 3785 const struct ieee80211_tx_queue_params *params) 3786 { 3787 struct b43_wl *wl = hw_to_b43_wl(hw); 3788 struct b43_wldev *dev; 3789 unsigned int queue = (unsigned int)_queue; 3790 int err = -ENODEV; 3791 3792 if (queue >= ARRAY_SIZE(wl->qos_params)) { 3793 /* Queue not available or don't support setting 3794 * params on this queue. Return success to not 3795 * confuse mac80211. */ 3796 return 0; 3797 } 3798 BUILD_BUG_ON(ARRAY_SIZE(b43_qos_shm_offsets) != 3799 ARRAY_SIZE(wl->qos_params)); 3800 3801 mutex_lock(&wl->mutex); 3802 dev = wl->current_dev; 3803 if (unlikely(!dev || (b43_status(dev) < B43_STAT_INITIALIZED))) 3804 goto out_unlock; 3805 3806 memcpy(&(wl->qos_params[queue].p), params, sizeof(*params)); 3807 b43_mac_suspend(dev); 3808 b43_qos_params_upload(dev, &(wl->qos_params[queue].p), 3809 b43_qos_shm_offsets[queue]); 3810 b43_mac_enable(dev); 3811 err = 0; 3812 3813 out_unlock: 3814 mutex_unlock(&wl->mutex); 3815 3816 return err; 3817 } 3818 3819 static int b43_op_get_stats(struct ieee80211_hw *hw, 3820 struct ieee80211_low_level_stats *stats) 3821 { 3822 struct b43_wl *wl = hw_to_b43_wl(hw); 3823 3824 mutex_lock(&wl->mutex); 3825 memcpy(stats, &wl->ieee_stats, sizeof(*stats)); 3826 mutex_unlock(&wl->mutex); 3827 3828 return 0; 3829 } 3830 3831 static u64 b43_op_get_tsf(struct ieee80211_hw *hw, struct ieee80211_vif *vif) 3832 { 3833 struct b43_wl *wl = hw_to_b43_wl(hw); 3834 struct b43_wldev *dev; 3835 u64 tsf; 3836 3837 mutex_lock(&wl->mutex); 3838 dev = wl->current_dev; 3839 3840 if (dev && (b43_status(dev) >= B43_STAT_INITIALIZED)) 3841 b43_tsf_read(dev, &tsf); 3842 else 3843 tsf = 0; 3844 3845 mutex_unlock(&wl->mutex); 3846 3847 return tsf; 3848 } 3849 3850 static void b43_op_set_tsf(struct ieee80211_hw *hw, 3851 struct ieee80211_vif *vif, u64 tsf) 3852 { 3853 struct b43_wl *wl = hw_to_b43_wl(hw); 3854 struct b43_wldev *dev; 3855 3856 mutex_lock(&wl->mutex); 3857 dev = wl->current_dev; 3858 3859 if (dev && (b43_status(dev) >= B43_STAT_INITIALIZED)) 3860 b43_tsf_write(dev, tsf); 3861 3862 mutex_unlock(&wl->mutex); 3863 } 3864 3865 static const char *band_to_string(enum nl80211_band band) 3866 { 3867 switch (band) { 3868 case NL80211_BAND_5GHZ: 3869 return "5"; 3870 case NL80211_BAND_2GHZ: 3871 return "2.4"; 3872 default: 3873 break; 3874 } 3875 B43_WARN_ON(1); 3876 return ""; 3877 } 3878 3879 /* Expects wl->mutex locked */ 3880 static int b43_switch_band(struct b43_wldev *dev, 3881 struct ieee80211_channel *chan) 3882 { 3883 struct b43_phy *phy = &dev->phy; 3884 bool gmode; 3885 u32 tmp; 3886 3887 switch (chan->band) { 3888 case NL80211_BAND_5GHZ: 3889 gmode = false; 3890 break; 3891 case NL80211_BAND_2GHZ: 3892 gmode = true; 3893 break; 3894 default: 3895 B43_WARN_ON(1); 3896 return -EINVAL; 3897 } 3898 3899 if (!((gmode && phy->supports_2ghz) || 3900 (!gmode && phy->supports_5ghz))) { 3901 b43err(dev->wl, "This device doesn't support %s-GHz band\n", 3902 band_to_string(chan->band)); 3903 return -ENODEV; 3904 } 3905 3906 if (!!phy->gmode == !!gmode) { 3907 /* This device is already running. */ 3908 return 0; 3909 } 3910 3911 b43dbg(dev->wl, "Switching to %s GHz band\n", 3912 band_to_string(chan->band)); 3913 3914 /* Some new devices don't need disabling radio for band switching */ 3915 if (!(phy->type == B43_PHYTYPE_N && phy->rev >= 3)) 3916 b43_software_rfkill(dev, true); 3917 3918 phy->gmode = gmode; 3919 b43_phy_put_into_reset(dev); 3920 switch (dev->dev->bus_type) { 3921 #ifdef CONFIG_B43_BCMA 3922 case B43_BUS_BCMA: 3923 tmp = bcma_aread32(dev->dev->bdev, BCMA_IOCTL); 3924 if (gmode) 3925 tmp |= B43_BCMA_IOCTL_GMODE; 3926 else 3927 tmp &= ~B43_BCMA_IOCTL_GMODE; 3928 bcma_awrite32(dev->dev->bdev, BCMA_IOCTL, tmp); 3929 break; 3930 #endif 3931 #ifdef CONFIG_B43_SSB 3932 case B43_BUS_SSB: 3933 tmp = ssb_read32(dev->dev->sdev, SSB_TMSLOW); 3934 if (gmode) 3935 tmp |= B43_TMSLOW_GMODE; 3936 else 3937 tmp &= ~B43_TMSLOW_GMODE; 3938 ssb_write32(dev->dev->sdev, SSB_TMSLOW, tmp); 3939 break; 3940 #endif 3941 } 3942 b43_phy_take_out_of_reset(dev); 3943 3944 b43_upload_initvals_band(dev); 3945 3946 b43_phy_init(dev); 3947 3948 return 0; 3949 } 3950 3951 static void b43_set_beacon_listen_interval(struct b43_wldev *dev, u16 interval) 3952 { 3953 interval = min_t(u16, interval, (u16)0xFF); 3954 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_BCN_LI, interval); 3955 } 3956 3957 /* Write the short and long frame retry limit values. */ 3958 static void b43_set_retry_limits(struct b43_wldev *dev, 3959 unsigned int short_retry, 3960 unsigned int long_retry) 3961 { 3962 /* The retry limit is a 4-bit counter. Enforce this to avoid overflowing 3963 * the chip-internal counter. */ 3964 short_retry = min(short_retry, (unsigned int)0xF); 3965 long_retry = min(long_retry, (unsigned int)0xF); 3966 3967 b43_shm_write16(dev, B43_SHM_SCRATCH, B43_SHM_SC_SRLIMIT, 3968 short_retry); 3969 b43_shm_write16(dev, B43_SHM_SCRATCH, B43_SHM_SC_LRLIMIT, 3970 long_retry); 3971 } 3972 3973 static int b43_op_config(struct ieee80211_hw *hw, u32 changed) 3974 { 3975 struct b43_wl *wl = hw_to_b43_wl(hw); 3976 struct b43_wldev *dev = wl->current_dev; 3977 struct b43_phy *phy = &dev->phy; 3978 struct ieee80211_conf *conf = &hw->conf; 3979 int antenna; 3980 int err = 0; 3981 3982 mutex_lock(&wl->mutex); 3983 b43_mac_suspend(dev); 3984 3985 if (changed & IEEE80211_CONF_CHANGE_LISTEN_INTERVAL) 3986 b43_set_beacon_listen_interval(dev, conf->listen_interval); 3987 3988 if (changed & IEEE80211_CONF_CHANGE_CHANNEL) { 3989 phy->chandef = &conf->chandef; 3990 phy->channel = conf->chandef.chan->hw_value; 3991 3992 /* Switch the band (if necessary). */ 3993 err = b43_switch_band(dev, conf->chandef.chan); 3994 if (err) 3995 goto out_mac_enable; 3996 3997 /* Switch to the requested channel. 3998 * The firmware takes care of races with the TX handler. 3999 */ 4000 b43_switch_channel(dev, phy->channel); 4001 } 4002 4003 if (changed & IEEE80211_CONF_CHANGE_RETRY_LIMITS) 4004 b43_set_retry_limits(dev, conf->short_frame_max_tx_count, 4005 conf->long_frame_max_tx_count); 4006 changed &= ~IEEE80211_CONF_CHANGE_RETRY_LIMITS; 4007 if (!changed) 4008 goto out_mac_enable; 4009 4010 dev->wl->radiotap_enabled = !!(conf->flags & IEEE80211_CONF_MONITOR); 4011 4012 /* Adjust the desired TX power level. */ 4013 if (conf->power_level != 0) { 4014 if (conf->power_level != phy->desired_txpower) { 4015 phy->desired_txpower = conf->power_level; 4016 b43_phy_txpower_check(dev, B43_TXPWR_IGNORE_TIME | 4017 B43_TXPWR_IGNORE_TSSI); 4018 } 4019 } 4020 4021 /* Antennas for RX and management frame TX. */ 4022 antenna = B43_ANTENNA_DEFAULT; 4023 b43_mgmtframe_txantenna(dev, antenna); 4024 antenna = B43_ANTENNA_DEFAULT; 4025 if (phy->ops->set_rx_antenna) 4026 phy->ops->set_rx_antenna(dev, antenna); 4027 4028 if (wl->radio_enabled != phy->radio_on) { 4029 if (wl->radio_enabled) { 4030 b43_software_rfkill(dev, false); 4031 b43info(dev->wl, "Radio turned on by software\n"); 4032 if (!dev->radio_hw_enable) { 4033 b43info(dev->wl, "The hardware RF-kill button " 4034 "still turns the radio physically off. " 4035 "Press the button to turn it on.\n"); 4036 } 4037 } else { 4038 b43_software_rfkill(dev, true); 4039 b43info(dev->wl, "Radio turned off by software\n"); 4040 } 4041 } 4042 4043 out_mac_enable: 4044 b43_mac_enable(dev); 4045 mutex_unlock(&wl->mutex); 4046 4047 return err; 4048 } 4049 4050 static void b43_update_basic_rates(struct b43_wldev *dev, u32 brates) 4051 { 4052 struct ieee80211_supported_band *sband = 4053 dev->wl->hw->wiphy->bands[b43_current_band(dev->wl)]; 4054 struct ieee80211_rate *rate; 4055 int i; 4056 u16 basic, direct, offset, basic_offset, rateptr; 4057 4058 for (i = 0; i < sband->n_bitrates; i++) { 4059 rate = &sband->bitrates[i]; 4060 4061 if (b43_is_cck_rate(rate->hw_value)) { 4062 direct = B43_SHM_SH_CCKDIRECT; 4063 basic = B43_SHM_SH_CCKBASIC; 4064 offset = b43_plcp_get_ratecode_cck(rate->hw_value); 4065 offset &= 0xF; 4066 } else { 4067 direct = B43_SHM_SH_OFDMDIRECT; 4068 basic = B43_SHM_SH_OFDMBASIC; 4069 offset = b43_plcp_get_ratecode_ofdm(rate->hw_value); 4070 offset &= 0xF; 4071 } 4072 4073 rate = ieee80211_get_response_rate(sband, brates, rate->bitrate); 4074 4075 if (b43_is_cck_rate(rate->hw_value)) { 4076 basic_offset = b43_plcp_get_ratecode_cck(rate->hw_value); 4077 basic_offset &= 0xF; 4078 } else { 4079 basic_offset = b43_plcp_get_ratecode_ofdm(rate->hw_value); 4080 basic_offset &= 0xF; 4081 } 4082 4083 /* 4084 * Get the pointer that we need to point to 4085 * from the direct map 4086 */ 4087 rateptr = b43_shm_read16(dev, B43_SHM_SHARED, 4088 direct + 2 * basic_offset); 4089 /* and write it to the basic map */ 4090 b43_shm_write16(dev, B43_SHM_SHARED, basic + 2 * offset, 4091 rateptr); 4092 } 4093 } 4094 4095 static void b43_op_bss_info_changed(struct ieee80211_hw *hw, 4096 struct ieee80211_vif *vif, 4097 struct ieee80211_bss_conf *conf, 4098 u32 changed) 4099 { 4100 struct b43_wl *wl = hw_to_b43_wl(hw); 4101 struct b43_wldev *dev; 4102 4103 mutex_lock(&wl->mutex); 4104 4105 dev = wl->current_dev; 4106 if (!dev || b43_status(dev) < B43_STAT_STARTED) 4107 goto out_unlock_mutex; 4108 4109 B43_WARN_ON(wl->vif != vif); 4110 4111 if (changed & BSS_CHANGED_BSSID) { 4112 if (conf->bssid) 4113 memcpy(wl->bssid, conf->bssid, ETH_ALEN); 4114 else 4115 eth_zero_addr(wl->bssid); 4116 } 4117 4118 if (b43_status(dev) >= B43_STAT_INITIALIZED) { 4119 if (changed & BSS_CHANGED_BEACON && 4120 (b43_is_mode(wl, NL80211_IFTYPE_AP) || 4121 b43_is_mode(wl, NL80211_IFTYPE_MESH_POINT) || 4122 b43_is_mode(wl, NL80211_IFTYPE_ADHOC))) 4123 b43_update_templates(wl); 4124 4125 if (changed & BSS_CHANGED_BSSID) 4126 b43_write_mac_bssid_templates(dev); 4127 } 4128 4129 b43_mac_suspend(dev); 4130 4131 /* Update templates for AP/mesh mode. */ 4132 if (changed & BSS_CHANGED_BEACON_INT && 4133 (b43_is_mode(wl, NL80211_IFTYPE_AP) || 4134 b43_is_mode(wl, NL80211_IFTYPE_MESH_POINT) || 4135 b43_is_mode(wl, NL80211_IFTYPE_ADHOC)) && 4136 conf->beacon_int) 4137 b43_set_beacon_int(dev, conf->beacon_int); 4138 4139 if (changed & BSS_CHANGED_BASIC_RATES) 4140 b43_update_basic_rates(dev, conf->basic_rates); 4141 4142 if (changed & BSS_CHANGED_ERP_SLOT) { 4143 if (conf->use_short_slot) 4144 b43_short_slot_timing_enable(dev); 4145 else 4146 b43_short_slot_timing_disable(dev); 4147 } 4148 4149 b43_mac_enable(dev); 4150 out_unlock_mutex: 4151 mutex_unlock(&wl->mutex); 4152 } 4153 4154 static int b43_op_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd, 4155 struct ieee80211_vif *vif, struct ieee80211_sta *sta, 4156 struct ieee80211_key_conf *key) 4157 { 4158 struct b43_wl *wl = hw_to_b43_wl(hw); 4159 struct b43_wldev *dev; 4160 u8 algorithm; 4161 u8 index; 4162 int err; 4163 static const u8 bcast_addr[ETH_ALEN] = { 0xff, 0xff, 0xff, 0xff, 0xff, 0xff }; 4164 4165 if (modparam_nohwcrypt) 4166 return -ENOSPC; /* User disabled HW-crypto */ 4167 4168 if ((vif->type == NL80211_IFTYPE_ADHOC || 4169 vif->type == NL80211_IFTYPE_MESH_POINT) && 4170 (key->cipher == WLAN_CIPHER_SUITE_TKIP || 4171 key->cipher == WLAN_CIPHER_SUITE_CCMP) && 4172 !(key->flags & IEEE80211_KEY_FLAG_PAIRWISE)) { 4173 /* 4174 * For now, disable hw crypto for the RSN IBSS group keys. This 4175 * could be optimized in the future, but until that gets 4176 * implemented, use of software crypto for group addressed 4177 * frames is a acceptable to allow RSN IBSS to be used. 4178 */ 4179 return -EOPNOTSUPP; 4180 } 4181 4182 mutex_lock(&wl->mutex); 4183 4184 dev = wl->current_dev; 4185 err = -ENODEV; 4186 if (!dev || b43_status(dev) < B43_STAT_INITIALIZED) 4187 goto out_unlock; 4188 4189 if (dev->fw.pcm_request_failed || !dev->hwcrypto_enabled) { 4190 /* We don't have firmware for the crypto engine. 4191 * Must use software-crypto. */ 4192 err = -EOPNOTSUPP; 4193 goto out_unlock; 4194 } 4195 4196 err = -EINVAL; 4197 switch (key->cipher) { 4198 case WLAN_CIPHER_SUITE_WEP40: 4199 algorithm = B43_SEC_ALGO_WEP40; 4200 break; 4201 case WLAN_CIPHER_SUITE_WEP104: 4202 algorithm = B43_SEC_ALGO_WEP104; 4203 break; 4204 case WLAN_CIPHER_SUITE_TKIP: 4205 algorithm = B43_SEC_ALGO_TKIP; 4206 break; 4207 case WLAN_CIPHER_SUITE_CCMP: 4208 algorithm = B43_SEC_ALGO_AES; 4209 break; 4210 default: 4211 B43_WARN_ON(1); 4212 goto out_unlock; 4213 } 4214 index = (u8) (key->keyidx); 4215 if (index > 3) 4216 goto out_unlock; 4217 4218 switch (cmd) { 4219 case SET_KEY: 4220 if (algorithm == B43_SEC_ALGO_TKIP && 4221 (!(key->flags & IEEE80211_KEY_FLAG_PAIRWISE) || 4222 !modparam_hwtkip)) { 4223 /* We support only pairwise key */ 4224 err = -EOPNOTSUPP; 4225 goto out_unlock; 4226 } 4227 4228 if (key->flags & IEEE80211_KEY_FLAG_PAIRWISE) { 4229 if (WARN_ON(!sta)) { 4230 err = -EOPNOTSUPP; 4231 goto out_unlock; 4232 } 4233 /* Pairwise key with an assigned MAC address. */ 4234 err = b43_key_write(dev, -1, algorithm, 4235 key->key, key->keylen, 4236 sta->addr, key); 4237 } else { 4238 /* Group key */ 4239 err = b43_key_write(dev, index, algorithm, 4240 key->key, key->keylen, NULL, key); 4241 } 4242 if (err) 4243 goto out_unlock; 4244 4245 if (algorithm == B43_SEC_ALGO_WEP40 || 4246 algorithm == B43_SEC_ALGO_WEP104) { 4247 b43_hf_write(dev, b43_hf_read(dev) | B43_HF_USEDEFKEYS); 4248 } else { 4249 b43_hf_write(dev, 4250 b43_hf_read(dev) & ~B43_HF_USEDEFKEYS); 4251 } 4252 key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV; 4253 if (algorithm == B43_SEC_ALGO_TKIP) 4254 key->flags |= IEEE80211_KEY_FLAG_GENERATE_MMIC; 4255 break; 4256 case DISABLE_KEY: { 4257 err = b43_key_clear(dev, key->hw_key_idx); 4258 if (err) 4259 goto out_unlock; 4260 break; 4261 } 4262 default: 4263 B43_WARN_ON(1); 4264 } 4265 4266 out_unlock: 4267 if (!err) { 4268 b43dbg(wl, "%s hardware based encryption for keyidx: %d, " 4269 "mac: %pM\n", 4270 cmd == SET_KEY ? "Using" : "Disabling", key->keyidx, 4271 sta ? sta->addr : bcast_addr); 4272 b43_dump_keymemory(dev); 4273 } 4274 mutex_unlock(&wl->mutex); 4275 4276 return err; 4277 } 4278 4279 static void b43_op_configure_filter(struct ieee80211_hw *hw, 4280 unsigned int changed, unsigned int *fflags, 4281 u64 multicast) 4282 { 4283 struct b43_wl *wl = hw_to_b43_wl(hw); 4284 struct b43_wldev *dev; 4285 4286 mutex_lock(&wl->mutex); 4287 dev = wl->current_dev; 4288 if (!dev) { 4289 *fflags = 0; 4290 goto out_unlock; 4291 } 4292 4293 *fflags &= FIF_ALLMULTI | 4294 FIF_FCSFAIL | 4295 FIF_PLCPFAIL | 4296 FIF_CONTROL | 4297 FIF_OTHER_BSS | 4298 FIF_BCN_PRBRESP_PROMISC; 4299 4300 changed &= FIF_ALLMULTI | 4301 FIF_FCSFAIL | 4302 FIF_PLCPFAIL | 4303 FIF_CONTROL | 4304 FIF_OTHER_BSS | 4305 FIF_BCN_PRBRESP_PROMISC; 4306 4307 wl->filter_flags = *fflags; 4308 4309 if (changed && b43_status(dev) >= B43_STAT_INITIALIZED) 4310 b43_adjust_opmode(dev); 4311 4312 out_unlock: 4313 mutex_unlock(&wl->mutex); 4314 } 4315 4316 /* Locking: wl->mutex 4317 * Returns the current dev. This might be different from the passed in dev, 4318 * because the core might be gone away while we unlocked the mutex. */ 4319 static struct b43_wldev * b43_wireless_core_stop(struct b43_wldev *dev) 4320 { 4321 struct b43_wl *wl; 4322 struct b43_wldev *orig_dev; 4323 u32 mask; 4324 int queue_num; 4325 4326 if (!dev) 4327 return NULL; 4328 wl = dev->wl; 4329 redo: 4330 if (!dev || b43_status(dev) < B43_STAT_STARTED) 4331 return dev; 4332 4333 /* Cancel work. Unlock to avoid deadlocks. */ 4334 mutex_unlock(&wl->mutex); 4335 cancel_delayed_work_sync(&dev->periodic_work); 4336 cancel_work_sync(&wl->tx_work); 4337 b43_leds_stop(dev); 4338 mutex_lock(&wl->mutex); 4339 dev = wl->current_dev; 4340 if (!dev || b43_status(dev) < B43_STAT_STARTED) { 4341 /* Whoops, aliens ate up the device while we were unlocked. */ 4342 return dev; 4343 } 4344 4345 /* Disable interrupts on the device. */ 4346 b43_set_status(dev, B43_STAT_INITIALIZED); 4347 if (b43_bus_host_is_sdio(dev->dev)) { 4348 /* wl->mutex is locked. That is enough. */ 4349 b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, 0); 4350 b43_read32(dev, B43_MMIO_GEN_IRQ_MASK); /* Flush */ 4351 } else { 4352 spin_lock_irq(&wl->hardirq_lock); 4353 b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, 0); 4354 b43_read32(dev, B43_MMIO_GEN_IRQ_MASK); /* Flush */ 4355 spin_unlock_irq(&wl->hardirq_lock); 4356 } 4357 /* Synchronize and free the interrupt handlers. Unlock to avoid deadlocks. */ 4358 orig_dev = dev; 4359 mutex_unlock(&wl->mutex); 4360 if (b43_bus_host_is_sdio(dev->dev)) 4361 b43_sdio_free_irq(dev); 4362 else 4363 free_irq(dev->dev->irq, dev); 4364 mutex_lock(&wl->mutex); 4365 dev = wl->current_dev; 4366 if (!dev) 4367 return dev; 4368 if (dev != orig_dev) { 4369 if (b43_status(dev) >= B43_STAT_STARTED) 4370 goto redo; 4371 return dev; 4372 } 4373 mask = b43_read32(dev, B43_MMIO_GEN_IRQ_MASK); 4374 B43_WARN_ON(mask != 0xFFFFFFFF && mask); 4375 4376 /* Drain all TX queues. */ 4377 for (queue_num = 0; queue_num < B43_QOS_QUEUE_NUM; queue_num++) { 4378 while (skb_queue_len(&wl->tx_queue[queue_num])) { 4379 struct sk_buff *skb; 4380 4381 skb = skb_dequeue(&wl->tx_queue[queue_num]); 4382 ieee80211_free_txskb(wl->hw, skb); 4383 } 4384 } 4385 4386 b43_mac_suspend(dev); 4387 b43_leds_exit(dev); 4388 b43dbg(wl, "Wireless interface stopped\n"); 4389 4390 return dev; 4391 } 4392 4393 /* Locking: wl->mutex */ 4394 static int b43_wireless_core_start(struct b43_wldev *dev) 4395 { 4396 int err; 4397 4398 B43_WARN_ON(b43_status(dev) != B43_STAT_INITIALIZED); 4399 4400 drain_txstatus_queue(dev); 4401 if (b43_bus_host_is_sdio(dev->dev)) { 4402 err = b43_sdio_request_irq(dev, b43_sdio_interrupt_handler); 4403 if (err) { 4404 b43err(dev->wl, "Cannot request SDIO IRQ\n"); 4405 goto out; 4406 } 4407 } else { 4408 err = request_threaded_irq(dev->dev->irq, b43_interrupt_handler, 4409 b43_interrupt_thread_handler, 4410 IRQF_SHARED, KBUILD_MODNAME, dev); 4411 if (err) { 4412 b43err(dev->wl, "Cannot request IRQ-%d\n", 4413 dev->dev->irq); 4414 goto out; 4415 } 4416 } 4417 4418 /* We are ready to run. */ 4419 ieee80211_wake_queues(dev->wl->hw); 4420 b43_set_status(dev, B43_STAT_STARTED); 4421 4422 /* Start data flow (TX/RX). */ 4423 b43_mac_enable(dev); 4424 b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, dev->irq_mask); 4425 4426 /* Start maintenance work */ 4427 b43_periodic_tasks_setup(dev); 4428 4429 b43_leds_init(dev); 4430 4431 b43dbg(dev->wl, "Wireless interface started\n"); 4432 out: 4433 return err; 4434 } 4435 4436 static char *b43_phy_name(struct b43_wldev *dev, u8 phy_type) 4437 { 4438 switch (phy_type) { 4439 case B43_PHYTYPE_A: 4440 return "A"; 4441 case B43_PHYTYPE_B: 4442 return "B"; 4443 case B43_PHYTYPE_G: 4444 return "G"; 4445 case B43_PHYTYPE_N: 4446 return "N"; 4447 case B43_PHYTYPE_LP: 4448 return "LP"; 4449 case B43_PHYTYPE_SSLPN: 4450 return "SSLPN"; 4451 case B43_PHYTYPE_HT: 4452 return "HT"; 4453 case B43_PHYTYPE_LCN: 4454 return "LCN"; 4455 case B43_PHYTYPE_LCNXN: 4456 return "LCNXN"; 4457 case B43_PHYTYPE_LCN40: 4458 return "LCN40"; 4459 case B43_PHYTYPE_AC: 4460 return "AC"; 4461 } 4462 return "UNKNOWN"; 4463 } 4464 4465 /* Get PHY and RADIO versioning numbers */ 4466 static int b43_phy_versioning(struct b43_wldev *dev) 4467 { 4468 struct b43_phy *phy = &dev->phy; 4469 const u8 core_rev = dev->dev->core_rev; 4470 u32 tmp; 4471 u8 analog_type; 4472 u8 phy_type; 4473 u8 phy_rev; 4474 u16 radio_manuf; 4475 u16 radio_id; 4476 u16 radio_rev; 4477 u8 radio_ver; 4478 int unsupported = 0; 4479 4480 /* Get PHY versioning */ 4481 tmp = b43_read16(dev, B43_MMIO_PHY_VER); 4482 analog_type = (tmp & B43_PHYVER_ANALOG) >> B43_PHYVER_ANALOG_SHIFT; 4483 phy_type = (tmp & B43_PHYVER_TYPE) >> B43_PHYVER_TYPE_SHIFT; 4484 phy_rev = (tmp & B43_PHYVER_VERSION); 4485 4486 /* LCNXN is continuation of N which run out of revisions */ 4487 if (phy_type == B43_PHYTYPE_LCNXN) { 4488 phy_type = B43_PHYTYPE_N; 4489 phy_rev += 16; 4490 } 4491 4492 switch (phy_type) { 4493 #ifdef CONFIG_B43_PHY_G 4494 case B43_PHYTYPE_G: 4495 if (phy_rev > 9) 4496 unsupported = 1; 4497 break; 4498 #endif 4499 #ifdef CONFIG_B43_PHY_N 4500 case B43_PHYTYPE_N: 4501 if (phy_rev >= 19) 4502 unsupported = 1; 4503 break; 4504 #endif 4505 #ifdef CONFIG_B43_PHY_LP 4506 case B43_PHYTYPE_LP: 4507 if (phy_rev > 2) 4508 unsupported = 1; 4509 break; 4510 #endif 4511 #ifdef CONFIG_B43_PHY_HT 4512 case B43_PHYTYPE_HT: 4513 if (phy_rev > 1) 4514 unsupported = 1; 4515 break; 4516 #endif 4517 #ifdef CONFIG_B43_PHY_LCN 4518 case B43_PHYTYPE_LCN: 4519 if (phy_rev > 1) 4520 unsupported = 1; 4521 break; 4522 #endif 4523 #ifdef CONFIG_B43_PHY_AC 4524 case B43_PHYTYPE_AC: 4525 if (phy_rev > 1) 4526 unsupported = 1; 4527 break; 4528 #endif 4529 default: 4530 unsupported = 1; 4531 } 4532 if (unsupported) { 4533 b43err(dev->wl, "FOUND UNSUPPORTED PHY (Analog %u, Type %d (%s), Revision %u)\n", 4534 analog_type, phy_type, b43_phy_name(dev, phy_type), 4535 phy_rev); 4536 return -EOPNOTSUPP; 4537 } 4538 b43info(dev->wl, "Found PHY: Analog %u, Type %d (%s), Revision %u\n", 4539 analog_type, phy_type, b43_phy_name(dev, phy_type), phy_rev); 4540 4541 /* Get RADIO versioning */ 4542 if (core_rev == 40 || core_rev == 42) { 4543 radio_manuf = 0x17F; 4544 4545 b43_write16f(dev, B43_MMIO_RADIO24_CONTROL, 0); 4546 radio_rev = b43_read16(dev, B43_MMIO_RADIO24_DATA); 4547 4548 b43_write16f(dev, B43_MMIO_RADIO24_CONTROL, 1); 4549 radio_id = b43_read16(dev, B43_MMIO_RADIO24_DATA); 4550 4551 radio_ver = 0; /* Is there version somewhere? */ 4552 } else if (core_rev >= 24) { 4553 u16 radio24[3]; 4554 4555 for (tmp = 0; tmp < 3; tmp++) { 4556 b43_write16f(dev, B43_MMIO_RADIO24_CONTROL, tmp); 4557 radio24[tmp] = b43_read16(dev, B43_MMIO_RADIO24_DATA); 4558 } 4559 4560 radio_manuf = 0x17F; 4561 radio_id = (radio24[2] << 8) | radio24[1]; 4562 radio_rev = (radio24[0] & 0xF); 4563 radio_ver = (radio24[0] & 0xF0) >> 4; 4564 } else { 4565 if (dev->dev->chip_id == 0x4317) { 4566 if (dev->dev->chip_rev == 0) 4567 tmp = 0x3205017F; 4568 else if (dev->dev->chip_rev == 1) 4569 tmp = 0x4205017F; 4570 else 4571 tmp = 0x5205017F; 4572 } else { 4573 b43_write16f(dev, B43_MMIO_RADIO_CONTROL, 4574 B43_RADIOCTL_ID); 4575 tmp = b43_read16(dev, B43_MMIO_RADIO_DATA_LOW); 4576 b43_write16f(dev, B43_MMIO_RADIO_CONTROL, 4577 B43_RADIOCTL_ID); 4578 tmp |= b43_read16(dev, B43_MMIO_RADIO_DATA_HIGH) << 16; 4579 } 4580 radio_manuf = (tmp & 0x00000FFF); 4581 radio_id = (tmp & 0x0FFFF000) >> 12; 4582 radio_rev = (tmp & 0xF0000000) >> 28; 4583 radio_ver = 0; /* Probably not available on old hw */ 4584 } 4585 4586 if (radio_manuf != 0x17F /* Broadcom */) 4587 unsupported = 1; 4588 switch (phy_type) { 4589 case B43_PHYTYPE_B: 4590 if ((radio_id & 0xFFF0) != 0x2050) 4591 unsupported = 1; 4592 break; 4593 case B43_PHYTYPE_G: 4594 if (radio_id != 0x2050) 4595 unsupported = 1; 4596 break; 4597 case B43_PHYTYPE_N: 4598 if (radio_id != 0x2055 && radio_id != 0x2056 && 4599 radio_id != 0x2057) 4600 unsupported = 1; 4601 if (radio_id == 0x2057 && 4602 !(radio_rev == 9 || radio_rev == 14)) 4603 unsupported = 1; 4604 break; 4605 case B43_PHYTYPE_LP: 4606 if (radio_id != 0x2062 && radio_id != 0x2063) 4607 unsupported = 1; 4608 break; 4609 case B43_PHYTYPE_HT: 4610 if (radio_id != 0x2059) 4611 unsupported = 1; 4612 break; 4613 case B43_PHYTYPE_LCN: 4614 if (radio_id != 0x2064) 4615 unsupported = 1; 4616 break; 4617 case B43_PHYTYPE_AC: 4618 if (radio_id != 0x2069) 4619 unsupported = 1; 4620 break; 4621 default: 4622 B43_WARN_ON(1); 4623 } 4624 if (unsupported) { 4625 b43err(dev->wl, 4626 "FOUND UNSUPPORTED RADIO (Manuf 0x%X, ID 0x%X, Revision %u, Version %u)\n", 4627 radio_manuf, radio_id, radio_rev, radio_ver); 4628 return -EOPNOTSUPP; 4629 } 4630 b43info(dev->wl, 4631 "Found Radio: Manuf 0x%X, ID 0x%X, Revision %u, Version %u\n", 4632 radio_manuf, radio_id, radio_rev, radio_ver); 4633 4634 /* FIXME: b43 treats "id" as "ver" and ignores the real "ver" */ 4635 phy->radio_manuf = radio_manuf; 4636 phy->radio_ver = radio_id; 4637 phy->radio_rev = radio_rev; 4638 4639 phy->analog = analog_type; 4640 phy->type = phy_type; 4641 phy->rev = phy_rev; 4642 4643 return 0; 4644 } 4645 4646 static void setup_struct_phy_for_init(struct b43_wldev *dev, 4647 struct b43_phy *phy) 4648 { 4649 phy->hardware_power_control = !!modparam_hwpctl; 4650 phy->next_txpwr_check_time = jiffies; 4651 /* PHY TX errors counter. */ 4652 atomic_set(&phy->txerr_cnt, B43_PHY_TX_BADNESS_LIMIT); 4653 4654 #if B43_DEBUG 4655 phy->phy_locked = false; 4656 phy->radio_locked = false; 4657 #endif 4658 } 4659 4660 static void setup_struct_wldev_for_init(struct b43_wldev *dev) 4661 { 4662 dev->dfq_valid = false; 4663 4664 /* Assume the radio is enabled. If it's not enabled, the state will 4665 * immediately get fixed on the first periodic work run. */ 4666 dev->radio_hw_enable = true; 4667 4668 /* Stats */ 4669 memset(&dev->stats, 0, sizeof(dev->stats)); 4670 4671 setup_struct_phy_for_init(dev, &dev->phy); 4672 4673 /* IRQ related flags */ 4674 dev->irq_reason = 0; 4675 memset(dev->dma_reason, 0, sizeof(dev->dma_reason)); 4676 dev->irq_mask = B43_IRQ_MASKTEMPLATE; 4677 if (b43_modparam_verbose < B43_VERBOSITY_DEBUG) 4678 dev->irq_mask &= ~B43_IRQ_PHY_TXERR; 4679 4680 dev->mac_suspended = 1; 4681 4682 /* Noise calculation context */ 4683 memset(&dev->noisecalc, 0, sizeof(dev->noisecalc)); 4684 } 4685 4686 static void b43_bluetooth_coext_enable(struct b43_wldev *dev) 4687 { 4688 struct ssb_sprom *sprom = dev->dev->bus_sprom; 4689 u64 hf; 4690 4691 if (!modparam_btcoex) 4692 return; 4693 if (!(sprom->boardflags_lo & B43_BFL_BTCOEXIST)) 4694 return; 4695 if (dev->phy.type != B43_PHYTYPE_B && !dev->phy.gmode) 4696 return; 4697 4698 hf = b43_hf_read(dev); 4699 if (sprom->boardflags_lo & B43_BFL_BTCMOD) 4700 hf |= B43_HF_BTCOEXALT; 4701 else 4702 hf |= B43_HF_BTCOEX; 4703 b43_hf_write(dev, hf); 4704 } 4705 4706 static void b43_bluetooth_coext_disable(struct b43_wldev *dev) 4707 { 4708 if (!modparam_btcoex) 4709 return; 4710 //TODO 4711 } 4712 4713 static void b43_imcfglo_timeouts_workaround(struct b43_wldev *dev) 4714 { 4715 struct ssb_bus *bus; 4716 u32 tmp; 4717 4718 #ifdef CONFIG_B43_SSB 4719 if (dev->dev->bus_type != B43_BUS_SSB) 4720 return; 4721 #else 4722 return; 4723 #endif 4724 4725 bus = dev->dev->sdev->bus; 4726 4727 if ((bus->chip_id == 0x4311 && bus->chip_rev == 2) || 4728 (bus->chip_id == 0x4312)) { 4729 tmp = ssb_read32(dev->dev->sdev, SSB_IMCFGLO); 4730 tmp &= ~SSB_IMCFGLO_REQTO; 4731 tmp &= ~SSB_IMCFGLO_SERTO; 4732 tmp |= 0x3; 4733 ssb_write32(dev->dev->sdev, SSB_IMCFGLO, tmp); 4734 ssb_commit_settings(bus); 4735 } 4736 } 4737 4738 static void b43_set_synth_pu_delay(struct b43_wldev *dev, bool idle) 4739 { 4740 u16 pu_delay; 4741 4742 /* The time value is in microseconds. */ 4743 pu_delay = 1050; 4744 if (b43_is_mode(dev->wl, NL80211_IFTYPE_ADHOC) || idle) 4745 pu_delay = 500; 4746 if ((dev->phy.radio_ver == 0x2050) && (dev->phy.radio_rev == 8)) 4747 pu_delay = max(pu_delay, (u16)2400); 4748 4749 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_SPUWKUP, pu_delay); 4750 } 4751 4752 /* Set the TSF CFP pre-TargetBeaconTransmissionTime. */ 4753 static void b43_set_pretbtt(struct b43_wldev *dev) 4754 { 4755 u16 pretbtt; 4756 4757 /* The time value is in microseconds. */ 4758 if (b43_is_mode(dev->wl, NL80211_IFTYPE_ADHOC)) 4759 pretbtt = 2; 4760 else 4761 pretbtt = 250; 4762 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_PRETBTT, pretbtt); 4763 b43_write16(dev, B43_MMIO_TSF_CFP_PRETBTT, pretbtt); 4764 } 4765 4766 /* Shutdown a wireless core */ 4767 /* Locking: wl->mutex */ 4768 static void b43_wireless_core_exit(struct b43_wldev *dev) 4769 { 4770 B43_WARN_ON(dev && b43_status(dev) > B43_STAT_INITIALIZED); 4771 if (!dev || b43_status(dev) != B43_STAT_INITIALIZED) 4772 return; 4773 4774 b43_set_status(dev, B43_STAT_UNINIT); 4775 4776 /* Stop the microcode PSM. */ 4777 b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_PSM_RUN, 4778 B43_MACCTL_PSM_JMP0); 4779 4780 switch (dev->dev->bus_type) { 4781 #ifdef CONFIG_B43_BCMA 4782 case B43_BUS_BCMA: 4783 bcma_host_pci_down(dev->dev->bdev->bus); 4784 break; 4785 #endif 4786 #ifdef CONFIG_B43_SSB 4787 case B43_BUS_SSB: 4788 /* TODO */ 4789 break; 4790 #endif 4791 } 4792 4793 b43_dma_free(dev); 4794 b43_pio_free(dev); 4795 b43_chip_exit(dev); 4796 dev->phy.ops->switch_analog(dev, 0); 4797 if (dev->wl->current_beacon) { 4798 dev_kfree_skb_any(dev->wl->current_beacon); 4799 dev->wl->current_beacon = NULL; 4800 } 4801 4802 b43_device_disable(dev, 0); 4803 b43_bus_may_powerdown(dev); 4804 } 4805 4806 /* Initialize a wireless core */ 4807 static int b43_wireless_core_init(struct b43_wldev *dev) 4808 { 4809 struct ssb_sprom *sprom = dev->dev->bus_sprom; 4810 struct b43_phy *phy = &dev->phy; 4811 int err; 4812 u64 hf; 4813 4814 B43_WARN_ON(b43_status(dev) != B43_STAT_UNINIT); 4815 4816 err = b43_bus_powerup(dev, 0); 4817 if (err) 4818 goto out; 4819 if (!b43_device_is_enabled(dev)) 4820 b43_wireless_core_reset(dev, phy->gmode); 4821 4822 /* Reset all data structures. */ 4823 setup_struct_wldev_for_init(dev); 4824 phy->ops->prepare_structs(dev); 4825 4826 /* Enable IRQ routing to this device. */ 4827 switch (dev->dev->bus_type) { 4828 #ifdef CONFIG_B43_BCMA 4829 case B43_BUS_BCMA: 4830 bcma_host_pci_irq_ctl(dev->dev->bdev->bus, 4831 dev->dev->bdev, true); 4832 bcma_host_pci_up(dev->dev->bdev->bus); 4833 break; 4834 #endif 4835 #ifdef CONFIG_B43_SSB 4836 case B43_BUS_SSB: 4837 ssb_pcicore_dev_irqvecs_enable(&dev->dev->sdev->bus->pcicore, 4838 dev->dev->sdev); 4839 break; 4840 #endif 4841 } 4842 4843 b43_imcfglo_timeouts_workaround(dev); 4844 b43_bluetooth_coext_disable(dev); 4845 if (phy->ops->prepare_hardware) { 4846 err = phy->ops->prepare_hardware(dev); 4847 if (err) 4848 goto err_busdown; 4849 } 4850 err = b43_chip_init(dev); 4851 if (err) 4852 goto err_busdown; 4853 b43_shm_write16(dev, B43_SHM_SHARED, 4854 B43_SHM_SH_WLCOREREV, dev->dev->core_rev); 4855 hf = b43_hf_read(dev); 4856 if (phy->type == B43_PHYTYPE_G) { 4857 hf |= B43_HF_SYMW; 4858 if (phy->rev == 1) 4859 hf |= B43_HF_GDCW; 4860 if (sprom->boardflags_lo & B43_BFL_PACTRL) 4861 hf |= B43_HF_OFDMPABOOST; 4862 } 4863 if (phy->radio_ver == 0x2050) { 4864 if (phy->radio_rev == 6) 4865 hf |= B43_HF_4318TSSI; 4866 if (phy->radio_rev < 6) 4867 hf |= B43_HF_VCORECALC; 4868 } 4869 if (sprom->boardflags_lo & B43_BFL_XTAL_NOSLOW) 4870 hf |= B43_HF_DSCRQ; /* Disable slowclock requests from ucode. */ 4871 #if defined(CONFIG_B43_SSB) && defined(CONFIG_SSB_DRIVER_PCICORE) 4872 if (dev->dev->bus_type == B43_BUS_SSB && 4873 dev->dev->sdev->bus->bustype == SSB_BUSTYPE_PCI && 4874 dev->dev->sdev->bus->pcicore.dev->id.revision <= 10) 4875 hf |= B43_HF_PCISCW; /* PCI slow clock workaround. */ 4876 #endif 4877 hf &= ~B43_HF_SKCFPUP; 4878 b43_hf_write(dev, hf); 4879 4880 /* tell the ucode MAC capabilities */ 4881 if (dev->dev->core_rev >= 13) { 4882 u32 mac_hw_cap = b43_read32(dev, B43_MMIO_MAC_HW_CAP); 4883 4884 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_MACHW_L, 4885 mac_hw_cap & 0xffff); 4886 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_MACHW_H, 4887 (mac_hw_cap >> 16) & 0xffff); 4888 } 4889 4890 b43_set_retry_limits(dev, B43_DEFAULT_SHORT_RETRY_LIMIT, 4891 B43_DEFAULT_LONG_RETRY_LIMIT); 4892 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_SFFBLIM, 3); 4893 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_LFFBLIM, 2); 4894 4895 /* Disable sending probe responses from firmware. 4896 * Setting the MaxTime to one usec will always trigger 4897 * a timeout, so we never send any probe resp. 4898 * A timeout of zero is infinite. */ 4899 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_PRMAXTIME, 1); 4900 4901 b43_rate_memory_init(dev); 4902 b43_set_phytxctl_defaults(dev); 4903 4904 /* Minimum Contention Window */ 4905 if (phy->type == B43_PHYTYPE_B) 4906 b43_shm_write16(dev, B43_SHM_SCRATCH, B43_SHM_SC_MINCONT, 0x1F); 4907 else 4908 b43_shm_write16(dev, B43_SHM_SCRATCH, B43_SHM_SC_MINCONT, 0xF); 4909 /* Maximum Contention Window */ 4910 b43_shm_write16(dev, B43_SHM_SCRATCH, B43_SHM_SC_MAXCONT, 0x3FF); 4911 4912 /* write phytype and phyvers */ 4913 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_PHYTYPE, phy->type); 4914 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_PHYVER, phy->rev); 4915 4916 if (b43_bus_host_is_pcmcia(dev->dev) || 4917 b43_bus_host_is_sdio(dev->dev)) { 4918 dev->__using_pio_transfers = true; 4919 err = b43_pio_init(dev); 4920 } else if (dev->use_pio) { 4921 b43warn(dev->wl, "Forced PIO by use_pio module parameter. " 4922 "This should not be needed and will result in lower " 4923 "performance.\n"); 4924 dev->__using_pio_transfers = true; 4925 err = b43_pio_init(dev); 4926 } else { 4927 dev->__using_pio_transfers = false; 4928 err = b43_dma_init(dev); 4929 } 4930 if (err) 4931 goto err_chip_exit; 4932 b43_qos_init(dev); 4933 b43_set_synth_pu_delay(dev, 1); 4934 b43_bluetooth_coext_enable(dev); 4935 4936 b43_bus_powerup(dev, !(sprom->boardflags_lo & B43_BFL_XTAL_NOSLOW)); 4937 b43_upload_card_macaddress(dev); 4938 b43_security_init(dev); 4939 4940 ieee80211_wake_queues(dev->wl->hw); 4941 4942 b43_set_status(dev, B43_STAT_INITIALIZED); 4943 4944 out: 4945 return err; 4946 4947 err_chip_exit: 4948 b43_chip_exit(dev); 4949 err_busdown: 4950 b43_bus_may_powerdown(dev); 4951 B43_WARN_ON(b43_status(dev) != B43_STAT_UNINIT); 4952 return err; 4953 } 4954 4955 static int b43_op_add_interface(struct ieee80211_hw *hw, 4956 struct ieee80211_vif *vif) 4957 { 4958 struct b43_wl *wl = hw_to_b43_wl(hw); 4959 struct b43_wldev *dev; 4960 int err = -EOPNOTSUPP; 4961 4962 /* TODO: allow WDS/AP devices to coexist */ 4963 4964 if (vif->type != NL80211_IFTYPE_AP && 4965 vif->type != NL80211_IFTYPE_MESH_POINT && 4966 vif->type != NL80211_IFTYPE_STATION && 4967 vif->type != NL80211_IFTYPE_WDS && 4968 vif->type != NL80211_IFTYPE_ADHOC) 4969 return -EOPNOTSUPP; 4970 4971 mutex_lock(&wl->mutex); 4972 if (wl->operating) 4973 goto out_mutex_unlock; 4974 4975 b43dbg(wl, "Adding Interface type %d\n", vif->type); 4976 4977 dev = wl->current_dev; 4978 wl->operating = true; 4979 wl->vif = vif; 4980 wl->if_type = vif->type; 4981 memcpy(wl->mac_addr, vif->addr, ETH_ALEN); 4982 4983 b43_adjust_opmode(dev); 4984 b43_set_pretbtt(dev); 4985 b43_set_synth_pu_delay(dev, 0); 4986 b43_upload_card_macaddress(dev); 4987 4988 err = 0; 4989 out_mutex_unlock: 4990 mutex_unlock(&wl->mutex); 4991 4992 if (err == 0) 4993 b43_op_bss_info_changed(hw, vif, &vif->bss_conf, ~0); 4994 4995 return err; 4996 } 4997 4998 static void b43_op_remove_interface(struct ieee80211_hw *hw, 4999 struct ieee80211_vif *vif) 5000 { 5001 struct b43_wl *wl = hw_to_b43_wl(hw); 5002 struct b43_wldev *dev = wl->current_dev; 5003 5004 b43dbg(wl, "Removing Interface type %d\n", vif->type); 5005 5006 mutex_lock(&wl->mutex); 5007 5008 B43_WARN_ON(!wl->operating); 5009 B43_WARN_ON(wl->vif != vif); 5010 wl->vif = NULL; 5011 5012 wl->operating = false; 5013 5014 b43_adjust_opmode(dev); 5015 eth_zero_addr(wl->mac_addr); 5016 b43_upload_card_macaddress(dev); 5017 5018 mutex_unlock(&wl->mutex); 5019 } 5020 5021 static int b43_op_start(struct ieee80211_hw *hw) 5022 { 5023 struct b43_wl *wl = hw_to_b43_wl(hw); 5024 struct b43_wldev *dev = wl->current_dev; 5025 int did_init = 0; 5026 int err = 0; 5027 5028 /* Kill all old instance specific information to make sure 5029 * the card won't use it in the short timeframe between start 5030 * and mac80211 reconfiguring it. */ 5031 eth_zero_addr(wl->bssid); 5032 eth_zero_addr(wl->mac_addr); 5033 wl->filter_flags = 0; 5034 wl->radiotap_enabled = false; 5035 b43_qos_clear(wl); 5036 wl->beacon0_uploaded = false; 5037 wl->beacon1_uploaded = false; 5038 wl->beacon_templates_virgin = true; 5039 wl->radio_enabled = true; 5040 5041 mutex_lock(&wl->mutex); 5042 5043 if (b43_status(dev) < B43_STAT_INITIALIZED) { 5044 err = b43_wireless_core_init(dev); 5045 if (err) 5046 goto out_mutex_unlock; 5047 did_init = 1; 5048 } 5049 5050 if (b43_status(dev) < B43_STAT_STARTED) { 5051 err = b43_wireless_core_start(dev); 5052 if (err) { 5053 if (did_init) 5054 b43_wireless_core_exit(dev); 5055 goto out_mutex_unlock; 5056 } 5057 } 5058 5059 /* XXX: only do if device doesn't support rfkill irq */ 5060 wiphy_rfkill_start_polling(hw->wiphy); 5061 5062 out_mutex_unlock: 5063 mutex_unlock(&wl->mutex); 5064 5065 /* 5066 * Configuration may have been overwritten during initialization. 5067 * Reload the configuration, but only if initialization was 5068 * successful. Reloading the configuration after a failed init 5069 * may hang the system. 5070 */ 5071 if (!err) 5072 b43_op_config(hw, ~0); 5073 5074 return err; 5075 } 5076 5077 static void b43_op_stop(struct ieee80211_hw *hw) 5078 { 5079 struct b43_wl *wl = hw_to_b43_wl(hw); 5080 struct b43_wldev *dev = wl->current_dev; 5081 5082 cancel_work_sync(&(wl->beacon_update_trigger)); 5083 5084 if (!dev) 5085 goto out; 5086 5087 mutex_lock(&wl->mutex); 5088 if (b43_status(dev) >= B43_STAT_STARTED) { 5089 dev = b43_wireless_core_stop(dev); 5090 if (!dev) 5091 goto out_unlock; 5092 } 5093 b43_wireless_core_exit(dev); 5094 wl->radio_enabled = false; 5095 5096 out_unlock: 5097 mutex_unlock(&wl->mutex); 5098 out: 5099 cancel_work_sync(&(wl->txpower_adjust_work)); 5100 } 5101 5102 static int b43_op_beacon_set_tim(struct ieee80211_hw *hw, 5103 struct ieee80211_sta *sta, bool set) 5104 { 5105 struct b43_wl *wl = hw_to_b43_wl(hw); 5106 5107 b43_update_templates(wl); 5108 5109 return 0; 5110 } 5111 5112 static void b43_op_sta_notify(struct ieee80211_hw *hw, 5113 struct ieee80211_vif *vif, 5114 enum sta_notify_cmd notify_cmd, 5115 struct ieee80211_sta *sta) 5116 { 5117 struct b43_wl *wl = hw_to_b43_wl(hw); 5118 5119 B43_WARN_ON(!vif || wl->vif != vif); 5120 } 5121 5122 static void b43_op_sw_scan_start_notifier(struct ieee80211_hw *hw, 5123 struct ieee80211_vif *vif, 5124 const u8 *mac_addr) 5125 { 5126 struct b43_wl *wl = hw_to_b43_wl(hw); 5127 struct b43_wldev *dev; 5128 5129 mutex_lock(&wl->mutex); 5130 dev = wl->current_dev; 5131 if (dev && (b43_status(dev) >= B43_STAT_INITIALIZED)) { 5132 /* Disable CFP update during scan on other channels. */ 5133 b43_hf_write(dev, b43_hf_read(dev) | B43_HF_SKCFPUP); 5134 } 5135 mutex_unlock(&wl->mutex); 5136 } 5137 5138 static void b43_op_sw_scan_complete_notifier(struct ieee80211_hw *hw, 5139 struct ieee80211_vif *vif) 5140 { 5141 struct b43_wl *wl = hw_to_b43_wl(hw); 5142 struct b43_wldev *dev; 5143 5144 mutex_lock(&wl->mutex); 5145 dev = wl->current_dev; 5146 if (dev && (b43_status(dev) >= B43_STAT_INITIALIZED)) { 5147 /* Re-enable CFP update. */ 5148 b43_hf_write(dev, b43_hf_read(dev) & ~B43_HF_SKCFPUP); 5149 } 5150 mutex_unlock(&wl->mutex); 5151 } 5152 5153 static int b43_op_get_survey(struct ieee80211_hw *hw, int idx, 5154 struct survey_info *survey) 5155 { 5156 struct b43_wl *wl = hw_to_b43_wl(hw); 5157 struct b43_wldev *dev = wl->current_dev; 5158 struct ieee80211_conf *conf = &hw->conf; 5159 5160 if (idx != 0) 5161 return -ENOENT; 5162 5163 survey->channel = conf->chandef.chan; 5164 survey->filled = SURVEY_INFO_NOISE_DBM; 5165 survey->noise = dev->stats.link_noise; 5166 5167 return 0; 5168 } 5169 5170 static const struct ieee80211_ops b43_hw_ops = { 5171 .tx = b43_op_tx, 5172 .conf_tx = b43_op_conf_tx, 5173 .add_interface = b43_op_add_interface, 5174 .remove_interface = b43_op_remove_interface, 5175 .config = b43_op_config, 5176 .bss_info_changed = b43_op_bss_info_changed, 5177 .configure_filter = b43_op_configure_filter, 5178 .set_key = b43_op_set_key, 5179 .update_tkip_key = b43_op_update_tkip_key, 5180 .get_stats = b43_op_get_stats, 5181 .get_tsf = b43_op_get_tsf, 5182 .set_tsf = b43_op_set_tsf, 5183 .start = b43_op_start, 5184 .stop = b43_op_stop, 5185 .set_tim = b43_op_beacon_set_tim, 5186 .sta_notify = b43_op_sta_notify, 5187 .sw_scan_start = b43_op_sw_scan_start_notifier, 5188 .sw_scan_complete = b43_op_sw_scan_complete_notifier, 5189 .get_survey = b43_op_get_survey, 5190 .rfkill_poll = b43_rfkill_poll, 5191 }; 5192 5193 /* Hard-reset the chip. Do not call this directly. 5194 * Use b43_controller_restart() 5195 */ 5196 static void b43_chip_reset(struct work_struct *work) 5197 { 5198 struct b43_wldev *dev = 5199 container_of(work, struct b43_wldev, restart_work); 5200 struct b43_wl *wl = dev->wl; 5201 int err = 0; 5202 int prev_status; 5203 5204 mutex_lock(&wl->mutex); 5205 5206 prev_status = b43_status(dev); 5207 /* Bring the device down... */ 5208 if (prev_status >= B43_STAT_STARTED) { 5209 dev = b43_wireless_core_stop(dev); 5210 if (!dev) { 5211 err = -ENODEV; 5212 goto out; 5213 } 5214 } 5215 if (prev_status >= B43_STAT_INITIALIZED) 5216 b43_wireless_core_exit(dev); 5217 5218 /* ...and up again. */ 5219 if (prev_status >= B43_STAT_INITIALIZED) { 5220 err = b43_wireless_core_init(dev); 5221 if (err) 5222 goto out; 5223 } 5224 if (prev_status >= B43_STAT_STARTED) { 5225 err = b43_wireless_core_start(dev); 5226 if (err) { 5227 b43_wireless_core_exit(dev); 5228 goto out; 5229 } 5230 } 5231 out: 5232 if (err) 5233 wl->current_dev = NULL; /* Failed to init the dev. */ 5234 mutex_unlock(&wl->mutex); 5235 5236 if (err) { 5237 b43err(wl, "Controller restart FAILED\n"); 5238 return; 5239 } 5240 5241 /* reload configuration */ 5242 b43_op_config(wl->hw, ~0); 5243 if (wl->vif) 5244 b43_op_bss_info_changed(wl->hw, wl->vif, &wl->vif->bss_conf, ~0); 5245 5246 b43info(wl, "Controller restarted\n"); 5247 } 5248 5249 static int b43_setup_bands(struct b43_wldev *dev, 5250 bool have_2ghz_phy, bool have_5ghz_phy) 5251 { 5252 struct ieee80211_hw *hw = dev->wl->hw; 5253 struct b43_phy *phy = &dev->phy; 5254 bool limited_2g; 5255 bool limited_5g; 5256 5257 /* We don't support all 2 GHz channels on some devices */ 5258 limited_2g = phy->radio_ver == 0x2057 && 5259 (phy->radio_rev == 9 || phy->radio_rev == 14); 5260 limited_5g = phy->radio_ver == 0x2057 && 5261 phy->radio_rev == 9; 5262 5263 if (have_2ghz_phy) 5264 hw->wiphy->bands[NL80211_BAND_2GHZ] = limited_2g ? 5265 &b43_band_2ghz_limited : &b43_band_2GHz; 5266 if (dev->phy.type == B43_PHYTYPE_N) { 5267 if (have_5ghz_phy) 5268 hw->wiphy->bands[NL80211_BAND_5GHZ] = limited_5g ? 5269 &b43_band_5GHz_nphy_limited : 5270 &b43_band_5GHz_nphy; 5271 } else { 5272 if (have_5ghz_phy) 5273 hw->wiphy->bands[NL80211_BAND_5GHZ] = &b43_band_5GHz_aphy; 5274 } 5275 5276 dev->phy.supports_2ghz = have_2ghz_phy; 5277 dev->phy.supports_5ghz = have_5ghz_phy; 5278 5279 return 0; 5280 } 5281 5282 static void b43_wireless_core_detach(struct b43_wldev *dev) 5283 { 5284 /* We release firmware that late to not be required to re-request 5285 * is all the time when we reinit the core. */ 5286 b43_release_firmware(dev); 5287 b43_phy_free(dev); 5288 } 5289 5290 static void b43_supported_bands(struct b43_wldev *dev, bool *have_2ghz_phy, 5291 bool *have_5ghz_phy) 5292 { 5293 u16 dev_id = 0; 5294 5295 #ifdef CONFIG_B43_BCMA 5296 if (dev->dev->bus_type == B43_BUS_BCMA && 5297 dev->dev->bdev->bus->hosttype == BCMA_HOSTTYPE_PCI) 5298 dev_id = dev->dev->bdev->bus->host_pci->device; 5299 #endif 5300 #ifdef CONFIG_B43_SSB 5301 if (dev->dev->bus_type == B43_BUS_SSB && 5302 dev->dev->sdev->bus->bustype == SSB_BUSTYPE_PCI) 5303 dev_id = dev->dev->sdev->bus->host_pci->device; 5304 #endif 5305 /* Override with SPROM value if available */ 5306 if (dev->dev->bus_sprom->dev_id) 5307 dev_id = dev->dev->bus_sprom->dev_id; 5308 5309 /* Note: below IDs can be "virtual" (not maching e.g. real PCI ID) */ 5310 switch (dev_id) { 5311 case 0x4324: /* BCM4306 */ 5312 case 0x4312: /* BCM4311 */ 5313 case 0x4319: /* BCM4318 */ 5314 case 0x4328: /* BCM4321 */ 5315 case 0x432b: /* BCM4322 */ 5316 case 0x4350: /* BCM43222 */ 5317 case 0x4353: /* BCM43224 */ 5318 case 0x0576: /* BCM43224 */ 5319 case 0x435f: /* BCM6362 */ 5320 case 0x4331: /* BCM4331 */ 5321 case 0x4359: /* BCM43228 */ 5322 case 0x43a0: /* BCM4360 */ 5323 case 0x43b1: /* BCM4352 */ 5324 /* Dual band devices */ 5325 *have_2ghz_phy = true; 5326 *have_5ghz_phy = true; 5327 return; 5328 case 0x4321: /* BCM4306 */ 5329 /* There are 14e4:4321 PCI devs with 2.4 GHz BCM4321 (N-PHY) */ 5330 if (dev->phy.type != B43_PHYTYPE_G) 5331 break; 5332 /* fall through */ 5333 case 0x4313: /* BCM4311 */ 5334 case 0x431a: /* BCM4318 */ 5335 case 0x432a: /* BCM4321 */ 5336 case 0x432d: /* BCM4322 */ 5337 case 0x4352: /* BCM43222 */ 5338 case 0x435a: /* BCM43228 */ 5339 case 0x4333: /* BCM4331 */ 5340 case 0x43a2: /* BCM4360 */ 5341 case 0x43b3: /* BCM4352 */ 5342 /* 5 GHz only devices */ 5343 *have_2ghz_phy = false; 5344 *have_5ghz_phy = true; 5345 return; 5346 } 5347 5348 /* As a fallback, try to guess using PHY type */ 5349 switch (dev->phy.type) { 5350 case B43_PHYTYPE_G: 5351 case B43_PHYTYPE_N: 5352 case B43_PHYTYPE_LP: 5353 case B43_PHYTYPE_HT: 5354 case B43_PHYTYPE_LCN: 5355 *have_2ghz_phy = true; 5356 *have_5ghz_phy = false; 5357 return; 5358 } 5359 5360 B43_WARN_ON(1); 5361 } 5362 5363 static int b43_wireless_core_attach(struct b43_wldev *dev) 5364 { 5365 struct b43_wl *wl = dev->wl; 5366 struct b43_phy *phy = &dev->phy; 5367 int err; 5368 u32 tmp; 5369 bool have_2ghz_phy = false, have_5ghz_phy = false; 5370 5371 /* Do NOT do any device initialization here. 5372 * Do it in wireless_core_init() instead. 5373 * This function is for gathering basic information about the HW, only. 5374 * Also some structs may be set up here. But most likely you want to have 5375 * that in core_init(), too. 5376 */ 5377 5378 err = b43_bus_powerup(dev, 0); 5379 if (err) { 5380 b43err(wl, "Bus powerup failed\n"); 5381 goto out; 5382 } 5383 5384 phy->do_full_init = true; 5385 5386 /* Try to guess supported bands for the first init needs */ 5387 switch (dev->dev->bus_type) { 5388 #ifdef CONFIG_B43_BCMA 5389 case B43_BUS_BCMA: 5390 tmp = bcma_aread32(dev->dev->bdev, BCMA_IOST); 5391 have_2ghz_phy = !!(tmp & B43_BCMA_IOST_2G_PHY); 5392 have_5ghz_phy = !!(tmp & B43_BCMA_IOST_5G_PHY); 5393 break; 5394 #endif 5395 #ifdef CONFIG_B43_SSB 5396 case B43_BUS_SSB: 5397 if (dev->dev->core_rev >= 5) { 5398 tmp = ssb_read32(dev->dev->sdev, SSB_TMSHIGH); 5399 have_2ghz_phy = !!(tmp & B43_TMSHIGH_HAVE_2GHZ_PHY); 5400 have_5ghz_phy = !!(tmp & B43_TMSHIGH_HAVE_5GHZ_PHY); 5401 } else 5402 B43_WARN_ON(1); 5403 break; 5404 #endif 5405 } 5406 5407 dev->phy.gmode = have_2ghz_phy; 5408 b43_wireless_core_reset(dev, dev->phy.gmode); 5409 5410 /* Get the PHY type. */ 5411 err = b43_phy_versioning(dev); 5412 if (err) 5413 goto err_powerdown; 5414 5415 /* Get real info about supported bands */ 5416 b43_supported_bands(dev, &have_2ghz_phy, &have_5ghz_phy); 5417 5418 /* We don't support 5 GHz on some PHYs yet */ 5419 if (have_5ghz_phy) { 5420 switch (dev->phy.type) { 5421 case B43_PHYTYPE_G: 5422 case B43_PHYTYPE_LP: 5423 case B43_PHYTYPE_HT: 5424 b43warn(wl, "5 GHz band is unsupported on this PHY\n"); 5425 have_5ghz_phy = false; 5426 } 5427 } 5428 5429 if (!have_2ghz_phy && !have_5ghz_phy) { 5430 b43err(wl, "b43 can't support any band on this device\n"); 5431 err = -EOPNOTSUPP; 5432 goto err_powerdown; 5433 } 5434 5435 err = b43_phy_allocate(dev); 5436 if (err) 5437 goto err_powerdown; 5438 5439 dev->phy.gmode = have_2ghz_phy; 5440 b43_wireless_core_reset(dev, dev->phy.gmode); 5441 5442 err = b43_validate_chipaccess(dev); 5443 if (err) 5444 goto err_phy_free; 5445 err = b43_setup_bands(dev, have_2ghz_phy, have_5ghz_phy); 5446 if (err) 5447 goto err_phy_free; 5448 5449 /* Now set some default "current_dev" */ 5450 if (!wl->current_dev) 5451 wl->current_dev = dev; 5452 INIT_WORK(&dev->restart_work, b43_chip_reset); 5453 5454 dev->phy.ops->switch_analog(dev, 0); 5455 b43_device_disable(dev, 0); 5456 b43_bus_may_powerdown(dev); 5457 5458 out: 5459 return err; 5460 5461 err_phy_free: 5462 b43_phy_free(dev); 5463 err_powerdown: 5464 b43_bus_may_powerdown(dev); 5465 return err; 5466 } 5467 5468 static void b43_one_core_detach(struct b43_bus_dev *dev) 5469 { 5470 struct b43_wldev *wldev; 5471 5472 /* Do not cancel ieee80211-workqueue based work here. 5473 * See comment in b43_remove(). */ 5474 5475 wldev = b43_bus_get_wldev(dev); 5476 b43_debugfs_remove_device(wldev); 5477 b43_wireless_core_detach(wldev); 5478 list_del(&wldev->list); 5479 b43_bus_set_wldev(dev, NULL); 5480 kfree(wldev); 5481 } 5482 5483 static int b43_one_core_attach(struct b43_bus_dev *dev, struct b43_wl *wl) 5484 { 5485 struct b43_wldev *wldev; 5486 int err = -ENOMEM; 5487 5488 wldev = kzalloc(sizeof(*wldev), GFP_KERNEL); 5489 if (!wldev) 5490 goto out; 5491 5492 wldev->use_pio = b43_modparam_pio; 5493 wldev->dev = dev; 5494 wldev->wl = wl; 5495 b43_set_status(wldev, B43_STAT_UNINIT); 5496 wldev->bad_frames_preempt = modparam_bad_frames_preempt; 5497 INIT_LIST_HEAD(&wldev->list); 5498 5499 err = b43_wireless_core_attach(wldev); 5500 if (err) 5501 goto err_kfree_wldev; 5502 5503 b43_bus_set_wldev(dev, wldev); 5504 b43_debugfs_add_device(wldev); 5505 5506 out: 5507 return err; 5508 5509 err_kfree_wldev: 5510 kfree(wldev); 5511 return err; 5512 } 5513 5514 #define IS_PDEV(pdev, _vendor, _device, _subvendor, _subdevice) ( \ 5515 (pdev->vendor == PCI_VENDOR_ID_##_vendor) && \ 5516 (pdev->device == _device) && \ 5517 (pdev->subsystem_vendor == PCI_VENDOR_ID_##_subvendor) && \ 5518 (pdev->subsystem_device == _subdevice) ) 5519 5520 #ifdef CONFIG_B43_SSB 5521 static void b43_sprom_fixup(struct ssb_bus *bus) 5522 { 5523 struct pci_dev *pdev; 5524 5525 /* boardflags workarounds */ 5526 if (bus->boardinfo.vendor == SSB_BOARDVENDOR_DELL && 5527 bus->chip_id == 0x4301 && bus->sprom.board_rev == 0x74) 5528 bus->sprom.boardflags_lo |= B43_BFL_BTCOEXIST; 5529 if (bus->boardinfo.vendor == PCI_VENDOR_ID_APPLE && 5530 bus->boardinfo.type == 0x4E && bus->sprom.board_rev > 0x40) 5531 bus->sprom.boardflags_lo |= B43_BFL_PACTRL; 5532 if (bus->bustype == SSB_BUSTYPE_PCI) { 5533 pdev = bus->host_pci; 5534 if (IS_PDEV(pdev, BROADCOM, 0x4318, ASUSTEK, 0x100F) || 5535 IS_PDEV(pdev, BROADCOM, 0x4320, DELL, 0x0003) || 5536 IS_PDEV(pdev, BROADCOM, 0x4320, HP, 0x12f8) || 5537 IS_PDEV(pdev, BROADCOM, 0x4320, LINKSYS, 0x0015) || 5538 IS_PDEV(pdev, BROADCOM, 0x4320, LINKSYS, 0x0014) || 5539 IS_PDEV(pdev, BROADCOM, 0x4320, LINKSYS, 0x0013) || 5540 IS_PDEV(pdev, BROADCOM, 0x4320, MOTOROLA, 0x7010)) 5541 bus->sprom.boardflags_lo &= ~B43_BFL_BTCOEXIST; 5542 } 5543 } 5544 5545 static void b43_wireless_exit(struct b43_bus_dev *dev, struct b43_wl *wl) 5546 { 5547 struct ieee80211_hw *hw = wl->hw; 5548 5549 ssb_set_devtypedata(dev->sdev, NULL); 5550 ieee80211_free_hw(hw); 5551 } 5552 #endif 5553 5554 static struct b43_wl *b43_wireless_init(struct b43_bus_dev *dev) 5555 { 5556 struct ssb_sprom *sprom = dev->bus_sprom; 5557 struct ieee80211_hw *hw; 5558 struct b43_wl *wl; 5559 char chip_name[6]; 5560 int queue_num; 5561 5562 hw = ieee80211_alloc_hw(sizeof(*wl), &b43_hw_ops); 5563 if (!hw) { 5564 b43err(NULL, "Could not allocate ieee80211 device\n"); 5565 return ERR_PTR(-ENOMEM); 5566 } 5567 wl = hw_to_b43_wl(hw); 5568 5569 /* fill hw info */ 5570 ieee80211_hw_set(hw, RX_INCLUDES_FCS); 5571 ieee80211_hw_set(hw, SIGNAL_DBM); 5572 5573 hw->wiphy->interface_modes = 5574 BIT(NL80211_IFTYPE_AP) | 5575 BIT(NL80211_IFTYPE_MESH_POINT) | 5576 BIT(NL80211_IFTYPE_STATION) | 5577 #ifdef CONFIG_WIRELESS_WDS 5578 BIT(NL80211_IFTYPE_WDS) | 5579 #endif 5580 BIT(NL80211_IFTYPE_ADHOC); 5581 5582 hw->wiphy->flags |= WIPHY_FLAG_IBSS_RSN; 5583 5584 wiphy_ext_feature_set(hw->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST); 5585 5586 wl->hw_registered = false; 5587 hw->max_rates = 2; 5588 SET_IEEE80211_DEV(hw, dev->dev); 5589 if (is_valid_ether_addr(sprom->et1mac)) 5590 SET_IEEE80211_PERM_ADDR(hw, sprom->et1mac); 5591 else 5592 SET_IEEE80211_PERM_ADDR(hw, sprom->il0mac); 5593 5594 /* Initialize struct b43_wl */ 5595 wl->hw = hw; 5596 mutex_init(&wl->mutex); 5597 spin_lock_init(&wl->hardirq_lock); 5598 spin_lock_init(&wl->beacon_lock); 5599 INIT_WORK(&wl->beacon_update_trigger, b43_beacon_update_trigger_work); 5600 INIT_WORK(&wl->txpower_adjust_work, b43_phy_txpower_adjust_work); 5601 INIT_WORK(&wl->tx_work, b43_tx_work); 5602 5603 /* Initialize queues and flags. */ 5604 for (queue_num = 0; queue_num < B43_QOS_QUEUE_NUM; queue_num++) { 5605 skb_queue_head_init(&wl->tx_queue[queue_num]); 5606 wl->tx_queue_stopped[queue_num] = false; 5607 } 5608 5609 snprintf(chip_name, ARRAY_SIZE(chip_name), 5610 (dev->chip_id > 0x9999) ? "%d" : "%04X", dev->chip_id); 5611 b43info(wl, "Broadcom %s WLAN found (core revision %u)\n", chip_name, 5612 dev->core_rev); 5613 return wl; 5614 } 5615 5616 #ifdef CONFIG_B43_BCMA 5617 static int b43_bcma_probe(struct bcma_device *core) 5618 { 5619 struct b43_bus_dev *dev; 5620 struct b43_wl *wl; 5621 int err; 5622 5623 if (!modparam_allhwsupport && 5624 (core->id.rev == 0x17 || core->id.rev == 0x18)) { 5625 pr_err("Support for cores revisions 0x17 and 0x18 disabled by module param allhwsupport=0. Try b43.allhwsupport=1\n"); 5626 return -ENOTSUPP; 5627 } 5628 5629 dev = b43_bus_dev_bcma_init(core); 5630 if (!dev) 5631 return -ENODEV; 5632 5633 wl = b43_wireless_init(dev); 5634 if (IS_ERR(wl)) { 5635 err = PTR_ERR(wl); 5636 goto bcma_out; 5637 } 5638 5639 err = b43_one_core_attach(dev, wl); 5640 if (err) 5641 goto bcma_err_wireless_exit; 5642 5643 /* setup and start work to load firmware */ 5644 INIT_WORK(&wl->firmware_load, b43_request_firmware); 5645 schedule_work(&wl->firmware_load); 5646 5647 return err; 5648 5649 bcma_err_wireless_exit: 5650 ieee80211_free_hw(wl->hw); 5651 bcma_out: 5652 kfree(dev); 5653 return err; 5654 } 5655 5656 static void b43_bcma_remove(struct bcma_device *core) 5657 { 5658 struct b43_wldev *wldev = bcma_get_drvdata(core); 5659 struct b43_wl *wl = wldev->wl; 5660 5661 /* We must cancel any work here before unregistering from ieee80211, 5662 * as the ieee80211 unreg will destroy the workqueue. */ 5663 cancel_work_sync(&wldev->restart_work); 5664 cancel_work_sync(&wl->firmware_load); 5665 5666 B43_WARN_ON(!wl); 5667 if (!wldev->fw.ucode.data) 5668 return; /* NULL if firmware never loaded */ 5669 if (wl->current_dev == wldev && wl->hw_registered) { 5670 b43_leds_stop(wldev); 5671 ieee80211_unregister_hw(wl->hw); 5672 } 5673 5674 b43_one_core_detach(wldev->dev); 5675 5676 /* Unregister HW RNG driver */ 5677 b43_rng_exit(wl); 5678 5679 b43_leds_unregister(wl); 5680 ieee80211_free_hw(wl->hw); 5681 kfree(wldev->dev); 5682 } 5683 5684 static struct bcma_driver b43_bcma_driver = { 5685 .name = KBUILD_MODNAME, 5686 .id_table = b43_bcma_tbl, 5687 .probe = b43_bcma_probe, 5688 .remove = b43_bcma_remove, 5689 }; 5690 #endif 5691 5692 #ifdef CONFIG_B43_SSB 5693 static 5694 int b43_ssb_probe(struct ssb_device *sdev, const struct ssb_device_id *id) 5695 { 5696 struct b43_bus_dev *dev; 5697 struct b43_wl *wl; 5698 int err; 5699 5700 dev = b43_bus_dev_ssb_init(sdev); 5701 if (!dev) 5702 return -ENOMEM; 5703 5704 wl = ssb_get_devtypedata(sdev); 5705 if (wl) { 5706 b43err(NULL, "Dual-core devices are not supported\n"); 5707 err = -ENOTSUPP; 5708 goto err_ssb_kfree_dev; 5709 } 5710 5711 b43_sprom_fixup(sdev->bus); 5712 5713 wl = b43_wireless_init(dev); 5714 if (IS_ERR(wl)) { 5715 err = PTR_ERR(wl); 5716 goto err_ssb_kfree_dev; 5717 } 5718 ssb_set_devtypedata(sdev, wl); 5719 B43_WARN_ON(ssb_get_devtypedata(sdev) != wl); 5720 5721 err = b43_one_core_attach(dev, wl); 5722 if (err) 5723 goto err_ssb_wireless_exit; 5724 5725 /* setup and start work to load firmware */ 5726 INIT_WORK(&wl->firmware_load, b43_request_firmware); 5727 schedule_work(&wl->firmware_load); 5728 5729 return err; 5730 5731 err_ssb_wireless_exit: 5732 b43_wireless_exit(dev, wl); 5733 err_ssb_kfree_dev: 5734 kfree(dev); 5735 return err; 5736 } 5737 5738 static void b43_ssb_remove(struct ssb_device *sdev) 5739 { 5740 struct b43_wl *wl = ssb_get_devtypedata(sdev); 5741 struct b43_wldev *wldev = ssb_get_drvdata(sdev); 5742 struct b43_bus_dev *dev = wldev->dev; 5743 5744 /* We must cancel any work here before unregistering from ieee80211, 5745 * as the ieee80211 unreg will destroy the workqueue. */ 5746 cancel_work_sync(&wldev->restart_work); 5747 cancel_work_sync(&wl->firmware_load); 5748 5749 B43_WARN_ON(!wl); 5750 if (!wldev->fw.ucode.data) 5751 return; /* NULL if firmware never loaded */ 5752 if (wl->current_dev == wldev && wl->hw_registered) { 5753 b43_leds_stop(wldev); 5754 ieee80211_unregister_hw(wl->hw); 5755 } 5756 5757 b43_one_core_detach(dev); 5758 5759 /* Unregister HW RNG driver */ 5760 b43_rng_exit(wl); 5761 5762 b43_leds_unregister(wl); 5763 b43_wireless_exit(dev, wl); 5764 kfree(dev); 5765 } 5766 5767 static struct ssb_driver b43_ssb_driver = { 5768 .name = KBUILD_MODNAME, 5769 .id_table = b43_ssb_tbl, 5770 .probe = b43_ssb_probe, 5771 .remove = b43_ssb_remove, 5772 }; 5773 #endif /* CONFIG_B43_SSB */ 5774 5775 /* Perform a hardware reset. This can be called from any context. */ 5776 void b43_controller_restart(struct b43_wldev *dev, const char *reason) 5777 { 5778 /* Must avoid requeueing, if we are in shutdown. */ 5779 if (b43_status(dev) < B43_STAT_INITIALIZED) 5780 return; 5781 b43info(dev->wl, "Controller RESET (%s) ...\n", reason); 5782 ieee80211_queue_work(dev->wl->hw, &dev->restart_work); 5783 } 5784 5785 static void b43_print_driverinfo(void) 5786 { 5787 const char *feat_pci = "", *feat_pcmcia = "", *feat_nphy = "", 5788 *feat_leds = "", *feat_sdio = ""; 5789 5790 #ifdef CONFIG_B43_PCI_AUTOSELECT 5791 feat_pci = "P"; 5792 #endif 5793 #ifdef CONFIG_B43_PCMCIA 5794 feat_pcmcia = "M"; 5795 #endif 5796 #ifdef CONFIG_B43_PHY_N 5797 feat_nphy = "N"; 5798 #endif 5799 #ifdef CONFIG_B43_LEDS 5800 feat_leds = "L"; 5801 #endif 5802 #ifdef CONFIG_B43_SDIO 5803 feat_sdio = "S"; 5804 #endif 5805 printk(KERN_INFO "Broadcom 43xx driver loaded " 5806 "[ Features: %s%s%s%s%s ]\n", 5807 feat_pci, feat_pcmcia, feat_nphy, 5808 feat_leds, feat_sdio); 5809 } 5810 5811 static int __init b43_init(void) 5812 { 5813 int err; 5814 5815 b43_debugfs_init(); 5816 err = b43_sdio_init(); 5817 if (err) 5818 goto err_dfs_exit; 5819 #ifdef CONFIG_B43_BCMA 5820 err = bcma_driver_register(&b43_bcma_driver); 5821 if (err) 5822 goto err_sdio_exit; 5823 #endif 5824 #ifdef CONFIG_B43_SSB 5825 err = ssb_driver_register(&b43_ssb_driver); 5826 if (err) 5827 goto err_bcma_driver_exit; 5828 #endif 5829 b43_print_driverinfo(); 5830 5831 return err; 5832 5833 #ifdef CONFIG_B43_SSB 5834 err_bcma_driver_exit: 5835 #endif 5836 #ifdef CONFIG_B43_BCMA 5837 bcma_driver_unregister(&b43_bcma_driver); 5838 err_sdio_exit: 5839 #endif 5840 b43_sdio_exit(); 5841 err_dfs_exit: 5842 b43_debugfs_exit(); 5843 return err; 5844 } 5845 5846 static void __exit b43_exit(void) 5847 { 5848 #ifdef CONFIG_B43_SSB 5849 ssb_driver_unregister(&b43_ssb_driver); 5850 #endif 5851 #ifdef CONFIG_B43_BCMA 5852 bcma_driver_unregister(&b43_bcma_driver); 5853 #endif 5854 b43_sdio_exit(); 5855 b43_debugfs_exit(); 5856 } 5857 5858 module_init(b43_init) 5859 module_exit(b43_exit) 5860