1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 4 Broadcom B43 wireless driver 5 6 Copyright (c) 2005 Martin Langer <martin-langer@gmx.de> 7 Copyright (c) 2005 Stefano Brivio <stefano.brivio@polimi.it> 8 Copyright (c) 2005-2009 Michael Buesch <m@bues.ch> 9 Copyright (c) 2005 Danny van Dyk <kugelfang@gentoo.org> 10 Copyright (c) 2005 Andreas Jaggi <andreas.jaggi@waterwave.ch> 11 Copyright (c) 2010-2011 Rafał Miłecki <zajec5@gmail.com> 12 13 SDIO support 14 Copyright (c) 2009 Albert Herranz <albert_herranz@yahoo.es> 15 16 Some parts of the code in this file are derived from the ipw2200 17 driver Copyright(c) 2003 - 2004 Intel Corporation. 18 19 20 */ 21 22 #include <linux/delay.h> 23 #include <linux/init.h> 24 #include <linux/module.h> 25 #include <linux/if_arp.h> 26 #include <linux/etherdevice.h> 27 #include <linux/firmware.h> 28 #include <linux/workqueue.h> 29 #include <linux/skbuff.h> 30 #include <linux/io.h> 31 #include <linux/dma-mapping.h> 32 #include <linux/slab.h> 33 #include <asm/unaligned.h> 34 35 #include "b43.h" 36 #include "main.h" 37 #include "debugfs.h" 38 #include "phy_common.h" 39 #include "phy_g.h" 40 #include "phy_n.h" 41 #include "dma.h" 42 #include "pio.h" 43 #include "sysfs.h" 44 #include "xmit.h" 45 #include "lo.h" 46 #include "sdio.h" 47 #include <linux/mmc/sdio_func.h> 48 49 MODULE_DESCRIPTION("Broadcom B43 wireless driver"); 50 MODULE_AUTHOR("Martin Langer"); 51 MODULE_AUTHOR("Stefano Brivio"); 52 MODULE_AUTHOR("Michael Buesch"); 53 MODULE_AUTHOR("Gábor Stefanik"); 54 MODULE_AUTHOR("Rafał Miłecki"); 55 MODULE_LICENSE("GPL"); 56 57 MODULE_FIRMWARE("b43/ucode11.fw"); 58 MODULE_FIRMWARE("b43/ucode13.fw"); 59 MODULE_FIRMWARE("b43/ucode14.fw"); 60 MODULE_FIRMWARE("b43/ucode15.fw"); 61 MODULE_FIRMWARE("b43/ucode16_lp.fw"); 62 MODULE_FIRMWARE("b43/ucode16_mimo.fw"); 63 MODULE_FIRMWARE("b43/ucode24_lcn.fw"); 64 MODULE_FIRMWARE("b43/ucode25_lcn.fw"); 65 MODULE_FIRMWARE("b43/ucode25_mimo.fw"); 66 MODULE_FIRMWARE("b43/ucode26_mimo.fw"); 67 MODULE_FIRMWARE("b43/ucode29_mimo.fw"); 68 MODULE_FIRMWARE("b43/ucode33_lcn40.fw"); 69 MODULE_FIRMWARE("b43/ucode30_mimo.fw"); 70 MODULE_FIRMWARE("b43/ucode5.fw"); 71 MODULE_FIRMWARE("b43/ucode40.fw"); 72 MODULE_FIRMWARE("b43/ucode42.fw"); 73 MODULE_FIRMWARE("b43/ucode9.fw"); 74 75 static int modparam_bad_frames_preempt; 76 module_param_named(bad_frames_preempt, modparam_bad_frames_preempt, int, 0444); 77 MODULE_PARM_DESC(bad_frames_preempt, 78 "enable(1) / disable(0) Bad Frames Preemption"); 79 80 static char modparam_fwpostfix[16]; 81 module_param_string(fwpostfix, modparam_fwpostfix, 16, 0444); 82 MODULE_PARM_DESC(fwpostfix, "Postfix for the .fw files to load."); 83 84 static int modparam_hwpctl; 85 module_param_named(hwpctl, modparam_hwpctl, int, 0444); 86 MODULE_PARM_DESC(hwpctl, "Enable hardware-side power control (default off)"); 87 88 static int modparam_nohwcrypt; 89 module_param_named(nohwcrypt, modparam_nohwcrypt, int, 0444); 90 MODULE_PARM_DESC(nohwcrypt, "Disable hardware encryption."); 91 92 static int modparam_hwtkip; 93 module_param_named(hwtkip, modparam_hwtkip, int, 0444); 94 MODULE_PARM_DESC(hwtkip, "Enable hardware tkip."); 95 96 static int modparam_qos = 1; 97 module_param_named(qos, modparam_qos, int, 0444); 98 MODULE_PARM_DESC(qos, "Enable QOS support (default on)"); 99 100 static int modparam_btcoex = 1; 101 module_param_named(btcoex, modparam_btcoex, int, 0444); 102 MODULE_PARM_DESC(btcoex, "Enable Bluetooth coexistence (default on)"); 103 104 int b43_modparam_verbose = B43_VERBOSITY_DEFAULT; 105 module_param_named(verbose, b43_modparam_verbose, int, 0644); 106 MODULE_PARM_DESC(verbose, "Log message verbosity: 0=error, 1=warn, 2=info(default), 3=debug"); 107 108 static int b43_modparam_pio = 0; 109 module_param_named(pio, b43_modparam_pio, int, 0644); 110 MODULE_PARM_DESC(pio, "Use PIO accesses by default: 0=DMA, 1=PIO"); 111 112 static int modparam_allhwsupport = !IS_ENABLED(CONFIG_BRCMSMAC); 113 module_param_named(allhwsupport, modparam_allhwsupport, int, 0444); 114 MODULE_PARM_DESC(allhwsupport, "Enable support for all hardware (even it if overlaps with the brcmsmac driver)"); 115 116 #ifdef CONFIG_B43_BCMA 117 static const struct bcma_device_id b43_bcma_tbl[] = { 118 BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x11, BCMA_ANY_CLASS), 119 BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x15, BCMA_ANY_CLASS), 120 BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x17, BCMA_ANY_CLASS), 121 BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x18, BCMA_ANY_CLASS), 122 BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x1C, BCMA_ANY_CLASS), 123 BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x1D, BCMA_ANY_CLASS), 124 BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x1E, BCMA_ANY_CLASS), 125 BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x28, BCMA_ANY_CLASS), 126 BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x2A, BCMA_ANY_CLASS), 127 {}, 128 }; 129 MODULE_DEVICE_TABLE(bcma, b43_bcma_tbl); 130 #endif 131 132 #ifdef CONFIG_B43_SSB 133 static const struct ssb_device_id b43_ssb_tbl[] = { 134 SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 5), 135 SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 6), 136 SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 7), 137 SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 9), 138 SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 10), 139 SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 11), 140 SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 12), 141 SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 13), 142 SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 15), 143 SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 16), 144 {}, 145 }; 146 MODULE_DEVICE_TABLE(ssb, b43_ssb_tbl); 147 #endif 148 149 /* Channel and ratetables are shared for all devices. 150 * They can't be const, because ieee80211 puts some precalculated 151 * data in there. This data is the same for all devices, so we don't 152 * get concurrency issues */ 153 #define RATETAB_ENT(_rateid, _flags) \ 154 { \ 155 .bitrate = B43_RATE_TO_BASE100KBPS(_rateid), \ 156 .hw_value = (_rateid), \ 157 .flags = (_flags), \ 158 } 159 160 /* 161 * NOTE: When changing this, sync with xmit.c's 162 * b43_plcp_get_bitrate_idx_* functions! 163 */ 164 static struct ieee80211_rate __b43_ratetable[] = { 165 RATETAB_ENT(B43_CCK_RATE_1MB, 0), 166 RATETAB_ENT(B43_CCK_RATE_2MB, IEEE80211_RATE_SHORT_PREAMBLE), 167 RATETAB_ENT(B43_CCK_RATE_5MB, IEEE80211_RATE_SHORT_PREAMBLE), 168 RATETAB_ENT(B43_CCK_RATE_11MB, IEEE80211_RATE_SHORT_PREAMBLE), 169 RATETAB_ENT(B43_OFDM_RATE_6MB, 0), 170 RATETAB_ENT(B43_OFDM_RATE_9MB, 0), 171 RATETAB_ENT(B43_OFDM_RATE_12MB, 0), 172 RATETAB_ENT(B43_OFDM_RATE_18MB, 0), 173 RATETAB_ENT(B43_OFDM_RATE_24MB, 0), 174 RATETAB_ENT(B43_OFDM_RATE_36MB, 0), 175 RATETAB_ENT(B43_OFDM_RATE_48MB, 0), 176 RATETAB_ENT(B43_OFDM_RATE_54MB, 0), 177 }; 178 179 #define b43_a_ratetable (__b43_ratetable + 4) 180 #define b43_a_ratetable_size 8 181 #define b43_b_ratetable (__b43_ratetable + 0) 182 #define b43_b_ratetable_size 4 183 #define b43_g_ratetable (__b43_ratetable + 0) 184 #define b43_g_ratetable_size 12 185 186 #define CHAN2G(_channel, _freq, _flags) { \ 187 .band = NL80211_BAND_2GHZ, \ 188 .center_freq = (_freq), \ 189 .hw_value = (_channel), \ 190 .flags = (_flags), \ 191 .max_antenna_gain = 0, \ 192 .max_power = 30, \ 193 } 194 static struct ieee80211_channel b43_2ghz_chantable[] = { 195 CHAN2G(1, 2412, 0), 196 CHAN2G(2, 2417, 0), 197 CHAN2G(3, 2422, 0), 198 CHAN2G(4, 2427, 0), 199 CHAN2G(5, 2432, 0), 200 CHAN2G(6, 2437, 0), 201 CHAN2G(7, 2442, 0), 202 CHAN2G(8, 2447, 0), 203 CHAN2G(9, 2452, 0), 204 CHAN2G(10, 2457, 0), 205 CHAN2G(11, 2462, 0), 206 CHAN2G(12, 2467, 0), 207 CHAN2G(13, 2472, 0), 208 CHAN2G(14, 2484, 0), 209 }; 210 211 /* No support for the last 3 channels (12, 13, 14) */ 212 #define b43_2ghz_chantable_limited_size 11 213 #undef CHAN2G 214 215 #define CHAN4G(_channel, _flags) { \ 216 .band = NL80211_BAND_5GHZ, \ 217 .center_freq = 4000 + (5 * (_channel)), \ 218 .hw_value = (_channel), \ 219 .flags = (_flags), \ 220 .max_antenna_gain = 0, \ 221 .max_power = 30, \ 222 } 223 #define CHAN5G(_channel, _flags) { \ 224 .band = NL80211_BAND_5GHZ, \ 225 .center_freq = 5000 + (5 * (_channel)), \ 226 .hw_value = (_channel), \ 227 .flags = (_flags), \ 228 .max_antenna_gain = 0, \ 229 .max_power = 30, \ 230 } 231 static struct ieee80211_channel b43_5ghz_nphy_chantable[] = { 232 CHAN4G(184, 0), CHAN4G(186, 0), 233 CHAN4G(188, 0), CHAN4G(190, 0), 234 CHAN4G(192, 0), CHAN4G(194, 0), 235 CHAN4G(196, 0), CHAN4G(198, 0), 236 CHAN4G(200, 0), CHAN4G(202, 0), 237 CHAN4G(204, 0), CHAN4G(206, 0), 238 CHAN4G(208, 0), CHAN4G(210, 0), 239 CHAN4G(212, 0), CHAN4G(214, 0), 240 CHAN4G(216, 0), CHAN4G(218, 0), 241 CHAN4G(220, 0), CHAN4G(222, 0), 242 CHAN4G(224, 0), CHAN4G(226, 0), 243 CHAN4G(228, 0), 244 CHAN5G(32, 0), CHAN5G(34, 0), 245 CHAN5G(36, 0), CHAN5G(38, 0), 246 CHAN5G(40, 0), CHAN5G(42, 0), 247 CHAN5G(44, 0), CHAN5G(46, 0), 248 CHAN5G(48, 0), CHAN5G(50, 0), 249 CHAN5G(52, 0), CHAN5G(54, 0), 250 CHAN5G(56, 0), CHAN5G(58, 0), 251 CHAN5G(60, 0), CHAN5G(62, 0), 252 CHAN5G(64, 0), CHAN5G(66, 0), 253 CHAN5G(68, 0), CHAN5G(70, 0), 254 CHAN5G(72, 0), CHAN5G(74, 0), 255 CHAN5G(76, 0), CHAN5G(78, 0), 256 CHAN5G(80, 0), CHAN5G(82, 0), 257 CHAN5G(84, 0), CHAN5G(86, 0), 258 CHAN5G(88, 0), CHAN5G(90, 0), 259 CHAN5G(92, 0), CHAN5G(94, 0), 260 CHAN5G(96, 0), CHAN5G(98, 0), 261 CHAN5G(100, 0), CHAN5G(102, 0), 262 CHAN5G(104, 0), CHAN5G(106, 0), 263 CHAN5G(108, 0), CHAN5G(110, 0), 264 CHAN5G(112, 0), CHAN5G(114, 0), 265 CHAN5G(116, 0), CHAN5G(118, 0), 266 CHAN5G(120, 0), CHAN5G(122, 0), 267 CHAN5G(124, 0), CHAN5G(126, 0), 268 CHAN5G(128, 0), CHAN5G(130, 0), 269 CHAN5G(132, 0), CHAN5G(134, 0), 270 CHAN5G(136, 0), CHAN5G(138, 0), 271 CHAN5G(140, 0), CHAN5G(142, 0), 272 CHAN5G(144, 0), CHAN5G(145, 0), 273 CHAN5G(146, 0), CHAN5G(147, 0), 274 CHAN5G(148, 0), CHAN5G(149, 0), 275 CHAN5G(150, 0), CHAN5G(151, 0), 276 CHAN5G(152, 0), CHAN5G(153, 0), 277 CHAN5G(154, 0), CHAN5G(155, 0), 278 CHAN5G(156, 0), CHAN5G(157, 0), 279 CHAN5G(158, 0), CHAN5G(159, 0), 280 CHAN5G(160, 0), CHAN5G(161, 0), 281 CHAN5G(162, 0), CHAN5G(163, 0), 282 CHAN5G(164, 0), CHAN5G(165, 0), 283 CHAN5G(166, 0), CHAN5G(168, 0), 284 CHAN5G(170, 0), CHAN5G(172, 0), 285 CHAN5G(174, 0), CHAN5G(176, 0), 286 CHAN5G(178, 0), CHAN5G(180, 0), 287 CHAN5G(182, 0), 288 }; 289 290 static struct ieee80211_channel b43_5ghz_nphy_chantable_limited[] = { 291 CHAN5G(36, 0), CHAN5G(40, 0), 292 CHAN5G(44, 0), CHAN5G(48, 0), 293 CHAN5G(149, 0), CHAN5G(153, 0), 294 CHAN5G(157, 0), CHAN5G(161, 0), 295 CHAN5G(165, 0), 296 }; 297 298 static struct ieee80211_channel b43_5ghz_aphy_chantable[] = { 299 CHAN5G(34, 0), CHAN5G(36, 0), 300 CHAN5G(38, 0), CHAN5G(40, 0), 301 CHAN5G(42, 0), CHAN5G(44, 0), 302 CHAN5G(46, 0), CHAN5G(48, 0), 303 CHAN5G(52, 0), CHAN5G(56, 0), 304 CHAN5G(60, 0), CHAN5G(64, 0), 305 CHAN5G(100, 0), CHAN5G(104, 0), 306 CHAN5G(108, 0), CHAN5G(112, 0), 307 CHAN5G(116, 0), CHAN5G(120, 0), 308 CHAN5G(124, 0), CHAN5G(128, 0), 309 CHAN5G(132, 0), CHAN5G(136, 0), 310 CHAN5G(140, 0), CHAN5G(149, 0), 311 CHAN5G(153, 0), CHAN5G(157, 0), 312 CHAN5G(161, 0), CHAN5G(165, 0), 313 CHAN5G(184, 0), CHAN5G(188, 0), 314 CHAN5G(192, 0), CHAN5G(196, 0), 315 CHAN5G(200, 0), CHAN5G(204, 0), 316 CHAN5G(208, 0), CHAN5G(212, 0), 317 CHAN5G(216, 0), 318 }; 319 #undef CHAN4G 320 #undef CHAN5G 321 322 static struct ieee80211_supported_band b43_band_5GHz_nphy = { 323 .band = NL80211_BAND_5GHZ, 324 .channels = b43_5ghz_nphy_chantable, 325 .n_channels = ARRAY_SIZE(b43_5ghz_nphy_chantable), 326 .bitrates = b43_a_ratetable, 327 .n_bitrates = b43_a_ratetable_size, 328 }; 329 330 static struct ieee80211_supported_band b43_band_5GHz_nphy_limited = { 331 .band = NL80211_BAND_5GHZ, 332 .channels = b43_5ghz_nphy_chantable_limited, 333 .n_channels = ARRAY_SIZE(b43_5ghz_nphy_chantable_limited), 334 .bitrates = b43_a_ratetable, 335 .n_bitrates = b43_a_ratetable_size, 336 }; 337 338 static struct ieee80211_supported_band b43_band_5GHz_aphy = { 339 .band = NL80211_BAND_5GHZ, 340 .channels = b43_5ghz_aphy_chantable, 341 .n_channels = ARRAY_SIZE(b43_5ghz_aphy_chantable), 342 .bitrates = b43_a_ratetable, 343 .n_bitrates = b43_a_ratetable_size, 344 }; 345 346 static struct ieee80211_supported_band b43_band_2GHz = { 347 .band = NL80211_BAND_2GHZ, 348 .channels = b43_2ghz_chantable, 349 .n_channels = ARRAY_SIZE(b43_2ghz_chantable), 350 .bitrates = b43_g_ratetable, 351 .n_bitrates = b43_g_ratetable_size, 352 }; 353 354 static struct ieee80211_supported_band b43_band_2ghz_limited = { 355 .band = NL80211_BAND_2GHZ, 356 .channels = b43_2ghz_chantable, 357 .n_channels = b43_2ghz_chantable_limited_size, 358 .bitrates = b43_g_ratetable, 359 .n_bitrates = b43_g_ratetable_size, 360 }; 361 362 static void b43_wireless_core_exit(struct b43_wldev *dev); 363 static int b43_wireless_core_init(struct b43_wldev *dev); 364 static struct b43_wldev * b43_wireless_core_stop(struct b43_wldev *dev); 365 static int b43_wireless_core_start(struct b43_wldev *dev); 366 static void b43_op_bss_info_changed(struct ieee80211_hw *hw, 367 struct ieee80211_vif *vif, 368 struct ieee80211_bss_conf *conf, 369 u32 changed); 370 371 static int b43_ratelimit(struct b43_wl *wl) 372 { 373 if (!wl || !wl->current_dev) 374 return 1; 375 if (b43_status(wl->current_dev) < B43_STAT_STARTED) 376 return 1; 377 /* We are up and running. 378 * Ratelimit the messages to avoid DoS over the net. */ 379 return net_ratelimit(); 380 } 381 382 void b43info(struct b43_wl *wl, const char *fmt, ...) 383 { 384 struct va_format vaf; 385 va_list args; 386 387 if (b43_modparam_verbose < B43_VERBOSITY_INFO) 388 return; 389 if (!b43_ratelimit(wl)) 390 return; 391 392 va_start(args, fmt); 393 394 vaf.fmt = fmt; 395 vaf.va = &args; 396 397 printk(KERN_INFO "b43-%s: %pV", 398 (wl && wl->hw) ? wiphy_name(wl->hw->wiphy) : "wlan", &vaf); 399 400 va_end(args); 401 } 402 403 void b43err(struct b43_wl *wl, const char *fmt, ...) 404 { 405 struct va_format vaf; 406 va_list args; 407 408 if (b43_modparam_verbose < B43_VERBOSITY_ERROR) 409 return; 410 if (!b43_ratelimit(wl)) 411 return; 412 413 va_start(args, fmt); 414 415 vaf.fmt = fmt; 416 vaf.va = &args; 417 418 printk(KERN_ERR "b43-%s ERROR: %pV", 419 (wl && wl->hw) ? wiphy_name(wl->hw->wiphy) : "wlan", &vaf); 420 421 va_end(args); 422 } 423 424 void b43warn(struct b43_wl *wl, const char *fmt, ...) 425 { 426 struct va_format vaf; 427 va_list args; 428 429 if (b43_modparam_verbose < B43_VERBOSITY_WARN) 430 return; 431 if (!b43_ratelimit(wl)) 432 return; 433 434 va_start(args, fmt); 435 436 vaf.fmt = fmt; 437 vaf.va = &args; 438 439 printk(KERN_WARNING "b43-%s warning: %pV", 440 (wl && wl->hw) ? wiphy_name(wl->hw->wiphy) : "wlan", &vaf); 441 442 va_end(args); 443 } 444 445 void b43dbg(struct b43_wl *wl, const char *fmt, ...) 446 { 447 struct va_format vaf; 448 va_list args; 449 450 if (b43_modparam_verbose < B43_VERBOSITY_DEBUG) 451 return; 452 453 va_start(args, fmt); 454 455 vaf.fmt = fmt; 456 vaf.va = &args; 457 458 printk(KERN_DEBUG "b43-%s debug: %pV", 459 (wl && wl->hw) ? wiphy_name(wl->hw->wiphy) : "wlan", &vaf); 460 461 va_end(args); 462 } 463 464 static void b43_ram_write(struct b43_wldev *dev, u16 offset, u32 val) 465 { 466 u32 macctl; 467 468 B43_WARN_ON(offset % 4 != 0); 469 470 macctl = b43_read32(dev, B43_MMIO_MACCTL); 471 if (macctl & B43_MACCTL_BE) 472 val = swab32(val); 473 474 b43_write32(dev, B43_MMIO_RAM_CONTROL, offset); 475 b43_write32(dev, B43_MMIO_RAM_DATA, val); 476 } 477 478 static inline void b43_shm_control_word(struct b43_wldev *dev, 479 u16 routing, u16 offset) 480 { 481 u32 control; 482 483 /* "offset" is the WORD offset. */ 484 control = routing; 485 control <<= 16; 486 control |= offset; 487 b43_write32(dev, B43_MMIO_SHM_CONTROL, control); 488 } 489 490 u32 b43_shm_read32(struct b43_wldev *dev, u16 routing, u16 offset) 491 { 492 u32 ret; 493 494 if (routing == B43_SHM_SHARED) { 495 B43_WARN_ON(offset & 0x0001); 496 if (offset & 0x0003) { 497 /* Unaligned access */ 498 b43_shm_control_word(dev, routing, offset >> 2); 499 ret = b43_read16(dev, B43_MMIO_SHM_DATA_UNALIGNED); 500 b43_shm_control_word(dev, routing, (offset >> 2) + 1); 501 ret |= ((u32)b43_read16(dev, B43_MMIO_SHM_DATA)) << 16; 502 503 goto out; 504 } 505 offset >>= 2; 506 } 507 b43_shm_control_word(dev, routing, offset); 508 ret = b43_read32(dev, B43_MMIO_SHM_DATA); 509 out: 510 return ret; 511 } 512 513 u16 b43_shm_read16(struct b43_wldev *dev, u16 routing, u16 offset) 514 { 515 u16 ret; 516 517 if (routing == B43_SHM_SHARED) { 518 B43_WARN_ON(offset & 0x0001); 519 if (offset & 0x0003) { 520 /* Unaligned access */ 521 b43_shm_control_word(dev, routing, offset >> 2); 522 ret = b43_read16(dev, B43_MMIO_SHM_DATA_UNALIGNED); 523 524 goto out; 525 } 526 offset >>= 2; 527 } 528 b43_shm_control_word(dev, routing, offset); 529 ret = b43_read16(dev, B43_MMIO_SHM_DATA); 530 out: 531 return ret; 532 } 533 534 void b43_shm_write32(struct b43_wldev *dev, u16 routing, u16 offset, u32 value) 535 { 536 if (routing == B43_SHM_SHARED) { 537 B43_WARN_ON(offset & 0x0001); 538 if (offset & 0x0003) { 539 /* Unaligned access */ 540 b43_shm_control_word(dev, routing, offset >> 2); 541 b43_write16(dev, B43_MMIO_SHM_DATA_UNALIGNED, 542 value & 0xFFFF); 543 b43_shm_control_word(dev, routing, (offset >> 2) + 1); 544 b43_write16(dev, B43_MMIO_SHM_DATA, 545 (value >> 16) & 0xFFFF); 546 return; 547 } 548 offset >>= 2; 549 } 550 b43_shm_control_word(dev, routing, offset); 551 b43_write32(dev, B43_MMIO_SHM_DATA, value); 552 } 553 554 void b43_shm_write16(struct b43_wldev *dev, u16 routing, u16 offset, u16 value) 555 { 556 if (routing == B43_SHM_SHARED) { 557 B43_WARN_ON(offset & 0x0001); 558 if (offset & 0x0003) { 559 /* Unaligned access */ 560 b43_shm_control_word(dev, routing, offset >> 2); 561 b43_write16(dev, B43_MMIO_SHM_DATA_UNALIGNED, value); 562 return; 563 } 564 offset >>= 2; 565 } 566 b43_shm_control_word(dev, routing, offset); 567 b43_write16(dev, B43_MMIO_SHM_DATA, value); 568 } 569 570 /* Read HostFlags */ 571 u64 b43_hf_read(struct b43_wldev *dev) 572 { 573 u64 ret; 574 575 ret = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTF3); 576 ret <<= 16; 577 ret |= b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTF2); 578 ret <<= 16; 579 ret |= b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTF1); 580 581 return ret; 582 } 583 584 /* Write HostFlags */ 585 void b43_hf_write(struct b43_wldev *dev, u64 value) 586 { 587 u16 lo, mi, hi; 588 589 lo = (value & 0x00000000FFFFULL); 590 mi = (value & 0x0000FFFF0000ULL) >> 16; 591 hi = (value & 0xFFFF00000000ULL) >> 32; 592 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTF1, lo); 593 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTF2, mi); 594 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTF3, hi); 595 } 596 597 /* Read the firmware capabilities bitmask (Opensource firmware only) */ 598 static u16 b43_fwcapa_read(struct b43_wldev *dev) 599 { 600 B43_WARN_ON(!dev->fw.opensource); 601 return b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_FWCAPA); 602 } 603 604 void b43_tsf_read(struct b43_wldev *dev, u64 *tsf) 605 { 606 u32 low, high; 607 608 B43_WARN_ON(dev->dev->core_rev < 3); 609 610 /* The hardware guarantees us an atomic read, if we 611 * read the low register first. */ 612 low = b43_read32(dev, B43_MMIO_REV3PLUS_TSF_LOW); 613 high = b43_read32(dev, B43_MMIO_REV3PLUS_TSF_HIGH); 614 615 *tsf = high; 616 *tsf <<= 32; 617 *tsf |= low; 618 } 619 620 static void b43_time_lock(struct b43_wldev *dev) 621 { 622 b43_maskset32(dev, B43_MMIO_MACCTL, ~0, B43_MACCTL_TBTTHOLD); 623 /* Commit the write */ 624 b43_read32(dev, B43_MMIO_MACCTL); 625 } 626 627 static void b43_time_unlock(struct b43_wldev *dev) 628 { 629 b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_TBTTHOLD, 0); 630 /* Commit the write */ 631 b43_read32(dev, B43_MMIO_MACCTL); 632 } 633 634 static void b43_tsf_write_locked(struct b43_wldev *dev, u64 tsf) 635 { 636 u32 low, high; 637 638 B43_WARN_ON(dev->dev->core_rev < 3); 639 640 low = tsf; 641 high = (tsf >> 32); 642 /* The hardware guarantees us an atomic write, if we 643 * write the low register first. */ 644 b43_write32(dev, B43_MMIO_REV3PLUS_TSF_LOW, low); 645 b43_write32(dev, B43_MMIO_REV3PLUS_TSF_HIGH, high); 646 } 647 648 void b43_tsf_write(struct b43_wldev *dev, u64 tsf) 649 { 650 b43_time_lock(dev); 651 b43_tsf_write_locked(dev, tsf); 652 b43_time_unlock(dev); 653 } 654 655 static 656 void b43_macfilter_set(struct b43_wldev *dev, u16 offset, const u8 *mac) 657 { 658 static const u8 zero_addr[ETH_ALEN] = { 0 }; 659 u16 data; 660 661 if (!mac) 662 mac = zero_addr; 663 664 offset |= 0x0020; 665 b43_write16(dev, B43_MMIO_MACFILTER_CONTROL, offset); 666 667 data = mac[0]; 668 data |= mac[1] << 8; 669 b43_write16(dev, B43_MMIO_MACFILTER_DATA, data); 670 data = mac[2]; 671 data |= mac[3] << 8; 672 b43_write16(dev, B43_MMIO_MACFILTER_DATA, data); 673 data = mac[4]; 674 data |= mac[5] << 8; 675 b43_write16(dev, B43_MMIO_MACFILTER_DATA, data); 676 } 677 678 static void b43_write_mac_bssid_templates(struct b43_wldev *dev) 679 { 680 const u8 *mac; 681 const u8 *bssid; 682 u8 mac_bssid[ETH_ALEN * 2]; 683 int i; 684 u32 tmp; 685 686 bssid = dev->wl->bssid; 687 mac = dev->wl->mac_addr; 688 689 b43_macfilter_set(dev, B43_MACFILTER_BSSID, bssid); 690 691 memcpy(mac_bssid, mac, ETH_ALEN); 692 memcpy(mac_bssid + ETH_ALEN, bssid, ETH_ALEN); 693 694 /* Write our MAC address and BSSID to template ram */ 695 for (i = 0; i < ARRAY_SIZE(mac_bssid); i += sizeof(u32)) { 696 tmp = (u32) (mac_bssid[i + 0]); 697 tmp |= (u32) (mac_bssid[i + 1]) << 8; 698 tmp |= (u32) (mac_bssid[i + 2]) << 16; 699 tmp |= (u32) (mac_bssid[i + 3]) << 24; 700 b43_ram_write(dev, 0x20 + i, tmp); 701 } 702 } 703 704 static void b43_upload_card_macaddress(struct b43_wldev *dev) 705 { 706 b43_write_mac_bssid_templates(dev); 707 b43_macfilter_set(dev, B43_MACFILTER_SELF, dev->wl->mac_addr); 708 } 709 710 static void b43_set_slot_time(struct b43_wldev *dev, u16 slot_time) 711 { 712 /* slot_time is in usec. */ 713 /* This test used to exit for all but a G PHY. */ 714 if (b43_current_band(dev->wl) == NL80211_BAND_5GHZ) 715 return; 716 b43_write16(dev, B43_MMIO_IFSSLOT, 510 + slot_time); 717 /* Shared memory location 0x0010 is the slot time and should be 718 * set to slot_time; however, this register is initially 0 and changing 719 * the value adversely affects the transmit rate for BCM4311 720 * devices. Until this behavior is unterstood, delete this step 721 * 722 * b43_shm_write16(dev, B43_SHM_SHARED, 0x0010, slot_time); 723 */ 724 } 725 726 static void b43_short_slot_timing_enable(struct b43_wldev *dev) 727 { 728 b43_set_slot_time(dev, 9); 729 } 730 731 static void b43_short_slot_timing_disable(struct b43_wldev *dev) 732 { 733 b43_set_slot_time(dev, 20); 734 } 735 736 /* DummyTransmission function, as documented on 737 * https://bcm-v4.sipsolutions.net/802.11/DummyTransmission 738 */ 739 void b43_dummy_transmission(struct b43_wldev *dev, bool ofdm, bool pa_on) 740 { 741 struct b43_phy *phy = &dev->phy; 742 unsigned int i, max_loop; 743 u16 value; 744 u32 buffer[5] = { 745 0x00000000, 746 0x00D40000, 747 0x00000000, 748 0x01000000, 749 0x00000000, 750 }; 751 752 if (ofdm) { 753 max_loop = 0x1E; 754 buffer[0] = 0x000201CC; 755 } else { 756 max_loop = 0xFA; 757 buffer[0] = 0x000B846E; 758 } 759 760 for (i = 0; i < 5; i++) 761 b43_ram_write(dev, i * 4, buffer[i]); 762 763 b43_write16(dev, B43_MMIO_XMTSEL, 0x0000); 764 765 if (dev->dev->core_rev < 11) 766 b43_write16(dev, B43_MMIO_WEPCTL, 0x0000); 767 else 768 b43_write16(dev, B43_MMIO_WEPCTL, 0x0100); 769 770 value = (ofdm ? 0x41 : 0x40); 771 b43_write16(dev, B43_MMIO_TXE0_PHYCTL, value); 772 if (phy->type == B43_PHYTYPE_N || phy->type == B43_PHYTYPE_LP || 773 phy->type == B43_PHYTYPE_LCN) 774 b43_write16(dev, B43_MMIO_TXE0_PHYCTL1, 0x1A02); 775 776 b43_write16(dev, B43_MMIO_TXE0_WM_0, 0x0000); 777 b43_write16(dev, B43_MMIO_TXE0_WM_1, 0x0000); 778 779 b43_write16(dev, B43_MMIO_XMTTPLATETXPTR, 0x0000); 780 b43_write16(dev, B43_MMIO_XMTTXCNT, 0x0014); 781 b43_write16(dev, B43_MMIO_XMTSEL, 0x0826); 782 b43_write16(dev, B43_MMIO_TXE0_CTL, 0x0000); 783 784 if (!pa_on && phy->type == B43_PHYTYPE_N) { 785 ; /*b43_nphy_pa_override(dev, false) */ 786 } 787 788 switch (phy->type) { 789 case B43_PHYTYPE_N: 790 case B43_PHYTYPE_LCN: 791 b43_write16(dev, B43_MMIO_TXE0_AUX, 0x00D0); 792 break; 793 case B43_PHYTYPE_LP: 794 b43_write16(dev, B43_MMIO_TXE0_AUX, 0x0050); 795 break; 796 default: 797 b43_write16(dev, B43_MMIO_TXE0_AUX, 0x0030); 798 } 799 b43_read16(dev, B43_MMIO_TXE0_AUX); 800 801 if (phy->radio_ver == 0x2050 && phy->radio_rev <= 0x5) 802 b43_radio_write16(dev, 0x0051, 0x0017); 803 for (i = 0x00; i < max_loop; i++) { 804 value = b43_read16(dev, B43_MMIO_TXE0_STATUS); 805 if (value & 0x0080) 806 break; 807 udelay(10); 808 } 809 for (i = 0x00; i < 0x0A; i++) { 810 value = b43_read16(dev, B43_MMIO_TXE0_STATUS); 811 if (value & 0x0400) 812 break; 813 udelay(10); 814 } 815 for (i = 0x00; i < 0x19; i++) { 816 value = b43_read16(dev, B43_MMIO_IFSSTAT); 817 if (!(value & 0x0100)) 818 break; 819 udelay(10); 820 } 821 if (phy->radio_ver == 0x2050 && phy->radio_rev <= 0x5) 822 b43_radio_write16(dev, 0x0051, 0x0037); 823 } 824 825 static void key_write(struct b43_wldev *dev, 826 u8 index, u8 algorithm, const u8 *key) 827 { 828 unsigned int i; 829 u32 offset; 830 u16 value; 831 u16 kidx; 832 833 /* Key index/algo block */ 834 kidx = b43_kidx_to_fw(dev, index); 835 value = ((kidx << 4) | algorithm); 836 b43_shm_write16(dev, B43_SHM_SHARED, 837 B43_SHM_SH_KEYIDXBLOCK + (kidx * 2), value); 838 839 /* Write the key to the Key Table Pointer offset */ 840 offset = dev->ktp + (index * B43_SEC_KEYSIZE); 841 for (i = 0; i < B43_SEC_KEYSIZE; i += 2) { 842 value = key[i]; 843 value |= (u16) (key[i + 1]) << 8; 844 b43_shm_write16(dev, B43_SHM_SHARED, offset + i, value); 845 } 846 } 847 848 static void keymac_write(struct b43_wldev *dev, u8 index, const u8 *addr) 849 { 850 u32 addrtmp[2] = { 0, 0, }; 851 u8 pairwise_keys_start = B43_NR_GROUP_KEYS * 2; 852 853 if (b43_new_kidx_api(dev)) 854 pairwise_keys_start = B43_NR_GROUP_KEYS; 855 856 B43_WARN_ON(index < pairwise_keys_start); 857 /* We have four default TX keys and possibly four default RX keys. 858 * Physical mac 0 is mapped to physical key 4 or 8, depending 859 * on the firmware version. 860 * So we must adjust the index here. 861 */ 862 index -= pairwise_keys_start; 863 B43_WARN_ON(index >= B43_NR_PAIRWISE_KEYS); 864 865 if (addr) { 866 addrtmp[0] = addr[0]; 867 addrtmp[0] |= ((u32) (addr[1]) << 8); 868 addrtmp[0] |= ((u32) (addr[2]) << 16); 869 addrtmp[0] |= ((u32) (addr[3]) << 24); 870 addrtmp[1] = addr[4]; 871 addrtmp[1] |= ((u32) (addr[5]) << 8); 872 } 873 874 /* Receive match transmitter address (RCMTA) mechanism */ 875 b43_shm_write32(dev, B43_SHM_RCMTA, 876 (index * 2) + 0, addrtmp[0]); 877 b43_shm_write16(dev, B43_SHM_RCMTA, 878 (index * 2) + 1, addrtmp[1]); 879 } 880 881 /* The ucode will use phase1 key with TEK key to decrypt rx packets. 882 * When a packet is received, the iv32 is checked. 883 * - if it doesn't the packet is returned without modification (and software 884 * decryption can be done). That's what happen when iv16 wrap. 885 * - if it does, the rc4 key is computed, and decryption is tried. 886 * Either it will success and B43_RX_MAC_DEC is returned, 887 * either it fails and B43_RX_MAC_DEC|B43_RX_MAC_DECERR is returned 888 * and the packet is not usable (it got modified by the ucode). 889 * So in order to never have B43_RX_MAC_DECERR, we should provide 890 * a iv32 and phase1key that match. Because we drop packets in case of 891 * B43_RX_MAC_DECERR, if we have a correct iv32 but a wrong phase1key, all 892 * packets will be lost without higher layer knowing (ie no resync possible 893 * until next wrap). 894 * 895 * NOTE : this should support 50 key like RCMTA because 896 * (B43_SHM_SH_KEYIDXBLOCK - B43_SHM_SH_TKIPTSCTTAK)/14 = 50 897 */ 898 static void rx_tkip_phase1_write(struct b43_wldev *dev, u8 index, u32 iv32, 899 u16 *phase1key) 900 { 901 unsigned int i; 902 u32 offset; 903 u8 pairwise_keys_start = B43_NR_GROUP_KEYS * 2; 904 905 if (!modparam_hwtkip) 906 return; 907 908 if (b43_new_kidx_api(dev)) 909 pairwise_keys_start = B43_NR_GROUP_KEYS; 910 911 B43_WARN_ON(index < pairwise_keys_start); 912 /* We have four default TX keys and possibly four default RX keys. 913 * Physical mac 0 is mapped to physical key 4 or 8, depending 914 * on the firmware version. 915 * So we must adjust the index here. 916 */ 917 index -= pairwise_keys_start; 918 B43_WARN_ON(index >= B43_NR_PAIRWISE_KEYS); 919 920 if (b43_debug(dev, B43_DBG_KEYS)) { 921 b43dbg(dev->wl, "rx_tkip_phase1_write : idx 0x%x, iv32 0x%x\n", 922 index, iv32); 923 } 924 /* Write the key to the RX tkip shared mem */ 925 offset = B43_SHM_SH_TKIPTSCTTAK + index * (10 + 4); 926 for (i = 0; i < 10; i += 2) { 927 b43_shm_write16(dev, B43_SHM_SHARED, offset + i, 928 phase1key ? phase1key[i / 2] : 0); 929 } 930 b43_shm_write16(dev, B43_SHM_SHARED, offset + i, iv32); 931 b43_shm_write16(dev, B43_SHM_SHARED, offset + i + 2, iv32 >> 16); 932 } 933 934 static void b43_op_update_tkip_key(struct ieee80211_hw *hw, 935 struct ieee80211_vif *vif, 936 struct ieee80211_key_conf *keyconf, 937 struct ieee80211_sta *sta, 938 u32 iv32, u16 *phase1key) 939 { 940 struct b43_wl *wl = hw_to_b43_wl(hw); 941 struct b43_wldev *dev; 942 int index = keyconf->hw_key_idx; 943 944 if (B43_WARN_ON(!modparam_hwtkip)) 945 return; 946 947 /* This is only called from the RX path through mac80211, where 948 * our mutex is already locked. */ 949 B43_WARN_ON(!mutex_is_locked(&wl->mutex)); 950 dev = wl->current_dev; 951 B43_WARN_ON(!dev || b43_status(dev) < B43_STAT_INITIALIZED); 952 953 keymac_write(dev, index, NULL); /* First zero out mac to avoid race */ 954 955 rx_tkip_phase1_write(dev, index, iv32, phase1key); 956 /* only pairwise TKIP keys are supported right now */ 957 if (WARN_ON(!sta)) 958 return; 959 keymac_write(dev, index, sta->addr); 960 } 961 962 static void do_key_write(struct b43_wldev *dev, 963 u8 index, u8 algorithm, 964 const u8 *key, size_t key_len, const u8 *mac_addr) 965 { 966 u8 buf[B43_SEC_KEYSIZE] = { 0, }; 967 u8 pairwise_keys_start = B43_NR_GROUP_KEYS * 2; 968 969 if (b43_new_kidx_api(dev)) 970 pairwise_keys_start = B43_NR_GROUP_KEYS; 971 972 B43_WARN_ON(index >= ARRAY_SIZE(dev->key)); 973 B43_WARN_ON(key_len > B43_SEC_KEYSIZE); 974 975 if (index >= pairwise_keys_start) 976 keymac_write(dev, index, NULL); /* First zero out mac. */ 977 if (algorithm == B43_SEC_ALGO_TKIP) { 978 /* 979 * We should provide an initial iv32, phase1key pair. 980 * We could start with iv32=0 and compute the corresponding 981 * phase1key, but this means calling ieee80211_get_tkip_key 982 * with a fake skb (or export other tkip function). 983 * Because we are lazy we hope iv32 won't start with 984 * 0xffffffff and let's b43_op_update_tkip_key provide a 985 * correct pair. 986 */ 987 rx_tkip_phase1_write(dev, index, 0xffffffff, (u16*)buf); 988 } else if (index >= pairwise_keys_start) /* clear it */ 989 rx_tkip_phase1_write(dev, index, 0, NULL); 990 if (key) 991 memcpy(buf, key, key_len); 992 key_write(dev, index, algorithm, buf); 993 if (index >= pairwise_keys_start) 994 keymac_write(dev, index, mac_addr); 995 996 dev->key[index].algorithm = algorithm; 997 } 998 999 static int b43_key_write(struct b43_wldev *dev, 1000 int index, u8 algorithm, 1001 const u8 *key, size_t key_len, 1002 const u8 *mac_addr, 1003 struct ieee80211_key_conf *keyconf) 1004 { 1005 int i; 1006 int pairwise_keys_start; 1007 1008 /* For ALG_TKIP the key is encoded as a 256-bit (32 byte) data block: 1009 * - Temporal Encryption Key (128 bits) 1010 * - Temporal Authenticator Tx MIC Key (64 bits) 1011 * - Temporal Authenticator Rx MIC Key (64 bits) 1012 * 1013 * Hardware only store TEK 1014 */ 1015 if (algorithm == B43_SEC_ALGO_TKIP && key_len == 32) 1016 key_len = 16; 1017 if (key_len > B43_SEC_KEYSIZE) 1018 return -EINVAL; 1019 for (i = 0; i < ARRAY_SIZE(dev->key); i++) { 1020 /* Check that we don't already have this key. */ 1021 B43_WARN_ON(dev->key[i].keyconf == keyconf); 1022 } 1023 if (index < 0) { 1024 /* Pairwise key. Get an empty slot for the key. */ 1025 if (b43_new_kidx_api(dev)) 1026 pairwise_keys_start = B43_NR_GROUP_KEYS; 1027 else 1028 pairwise_keys_start = B43_NR_GROUP_KEYS * 2; 1029 for (i = pairwise_keys_start; 1030 i < pairwise_keys_start + B43_NR_PAIRWISE_KEYS; 1031 i++) { 1032 B43_WARN_ON(i >= ARRAY_SIZE(dev->key)); 1033 if (!dev->key[i].keyconf) { 1034 /* found empty */ 1035 index = i; 1036 break; 1037 } 1038 } 1039 if (index < 0) { 1040 b43warn(dev->wl, "Out of hardware key memory\n"); 1041 return -ENOSPC; 1042 } 1043 } else 1044 B43_WARN_ON(index > 3); 1045 1046 do_key_write(dev, index, algorithm, key, key_len, mac_addr); 1047 if ((index <= 3) && !b43_new_kidx_api(dev)) { 1048 /* Default RX key */ 1049 B43_WARN_ON(mac_addr); 1050 do_key_write(dev, index + 4, algorithm, key, key_len, NULL); 1051 } 1052 keyconf->hw_key_idx = index; 1053 dev->key[index].keyconf = keyconf; 1054 1055 return 0; 1056 } 1057 1058 static int b43_key_clear(struct b43_wldev *dev, int index) 1059 { 1060 if (B43_WARN_ON((index < 0) || (index >= ARRAY_SIZE(dev->key)))) 1061 return -EINVAL; 1062 do_key_write(dev, index, B43_SEC_ALGO_NONE, 1063 NULL, B43_SEC_KEYSIZE, NULL); 1064 if ((index <= 3) && !b43_new_kidx_api(dev)) { 1065 do_key_write(dev, index + 4, B43_SEC_ALGO_NONE, 1066 NULL, B43_SEC_KEYSIZE, NULL); 1067 } 1068 dev->key[index].keyconf = NULL; 1069 1070 return 0; 1071 } 1072 1073 static void b43_clear_keys(struct b43_wldev *dev) 1074 { 1075 int i, count; 1076 1077 if (b43_new_kidx_api(dev)) 1078 count = B43_NR_GROUP_KEYS + B43_NR_PAIRWISE_KEYS; 1079 else 1080 count = B43_NR_GROUP_KEYS * 2 + B43_NR_PAIRWISE_KEYS; 1081 for (i = 0; i < count; i++) 1082 b43_key_clear(dev, i); 1083 } 1084 1085 static void b43_dump_keymemory(struct b43_wldev *dev) 1086 { 1087 unsigned int i, index, count, offset, pairwise_keys_start; 1088 u8 mac[ETH_ALEN]; 1089 u16 algo; 1090 u32 rcmta0; 1091 u16 rcmta1; 1092 u64 hf; 1093 struct b43_key *key; 1094 1095 if (!b43_debug(dev, B43_DBG_KEYS)) 1096 return; 1097 1098 hf = b43_hf_read(dev); 1099 b43dbg(dev->wl, "Hardware key memory dump: USEDEFKEYS=%u\n", 1100 !!(hf & B43_HF_USEDEFKEYS)); 1101 if (b43_new_kidx_api(dev)) { 1102 pairwise_keys_start = B43_NR_GROUP_KEYS; 1103 count = B43_NR_GROUP_KEYS + B43_NR_PAIRWISE_KEYS; 1104 } else { 1105 pairwise_keys_start = B43_NR_GROUP_KEYS * 2; 1106 count = B43_NR_GROUP_KEYS * 2 + B43_NR_PAIRWISE_KEYS; 1107 } 1108 for (index = 0; index < count; index++) { 1109 key = &(dev->key[index]); 1110 printk(KERN_DEBUG "Key slot %02u: %s", 1111 index, (key->keyconf == NULL) ? " " : "*"); 1112 offset = dev->ktp + (index * B43_SEC_KEYSIZE); 1113 for (i = 0; i < B43_SEC_KEYSIZE; i += 2) { 1114 u16 tmp = b43_shm_read16(dev, B43_SHM_SHARED, offset + i); 1115 printk("%02X%02X", (tmp & 0xFF), ((tmp >> 8) & 0xFF)); 1116 } 1117 1118 algo = b43_shm_read16(dev, B43_SHM_SHARED, 1119 B43_SHM_SH_KEYIDXBLOCK + (index * 2)); 1120 printk(" Algo: %04X/%02X", algo, key->algorithm); 1121 1122 if (index >= pairwise_keys_start) { 1123 if (key->algorithm == B43_SEC_ALGO_TKIP) { 1124 printk(" TKIP: "); 1125 offset = B43_SHM_SH_TKIPTSCTTAK + (index - 4) * (10 + 4); 1126 for (i = 0; i < 14; i += 2) { 1127 u16 tmp = b43_shm_read16(dev, B43_SHM_SHARED, offset + i); 1128 printk("%02X%02X", (tmp & 0xFF), ((tmp >> 8) & 0xFF)); 1129 } 1130 } 1131 rcmta0 = b43_shm_read32(dev, B43_SHM_RCMTA, 1132 ((index - pairwise_keys_start) * 2) + 0); 1133 rcmta1 = b43_shm_read16(dev, B43_SHM_RCMTA, 1134 ((index - pairwise_keys_start) * 2) + 1); 1135 *((__le32 *)(&mac[0])) = cpu_to_le32(rcmta0); 1136 *((__le16 *)(&mac[4])) = cpu_to_le16(rcmta1); 1137 printk(" MAC: %pM", mac); 1138 } else 1139 printk(" DEFAULT KEY"); 1140 printk("\n"); 1141 } 1142 } 1143 1144 void b43_power_saving_ctl_bits(struct b43_wldev *dev, unsigned int ps_flags) 1145 { 1146 u32 macctl; 1147 u16 ucstat; 1148 bool hwps; 1149 bool awake; 1150 int i; 1151 1152 B43_WARN_ON((ps_flags & B43_PS_ENABLED) && 1153 (ps_flags & B43_PS_DISABLED)); 1154 B43_WARN_ON((ps_flags & B43_PS_AWAKE) && (ps_flags & B43_PS_ASLEEP)); 1155 1156 if (ps_flags & B43_PS_ENABLED) { 1157 hwps = true; 1158 } else if (ps_flags & B43_PS_DISABLED) { 1159 hwps = false; 1160 } else { 1161 //TODO: If powersave is not off and FIXME is not set and we are not in adhoc 1162 // and thus is not an AP and we are associated, set bit 25 1163 } 1164 if (ps_flags & B43_PS_AWAKE) { 1165 awake = true; 1166 } else if (ps_flags & B43_PS_ASLEEP) { 1167 awake = false; 1168 } else { 1169 //TODO: If the device is awake or this is an AP, or we are scanning, or FIXME, 1170 // or we are associated, or FIXME, or the latest PS-Poll packet sent was 1171 // successful, set bit26 1172 } 1173 1174 /* FIXME: For now we force awake-on and hwps-off */ 1175 hwps = false; 1176 awake = true; 1177 1178 macctl = b43_read32(dev, B43_MMIO_MACCTL); 1179 if (hwps) 1180 macctl |= B43_MACCTL_HWPS; 1181 else 1182 macctl &= ~B43_MACCTL_HWPS; 1183 if (awake) 1184 macctl |= B43_MACCTL_AWAKE; 1185 else 1186 macctl &= ~B43_MACCTL_AWAKE; 1187 b43_write32(dev, B43_MMIO_MACCTL, macctl); 1188 /* Commit write */ 1189 b43_read32(dev, B43_MMIO_MACCTL); 1190 if (awake && dev->dev->core_rev >= 5) { 1191 /* Wait for the microcode to wake up. */ 1192 for (i = 0; i < 100; i++) { 1193 ucstat = b43_shm_read16(dev, B43_SHM_SHARED, 1194 B43_SHM_SH_UCODESTAT); 1195 if (ucstat != B43_SHM_SH_UCODESTAT_SLEEP) 1196 break; 1197 udelay(10); 1198 } 1199 } 1200 } 1201 1202 /* https://bcm-v4.sipsolutions.net/802.11/PHY/BmacCorePllReset */ 1203 void b43_wireless_core_phy_pll_reset(struct b43_wldev *dev) 1204 { 1205 struct bcma_drv_cc *bcma_cc __maybe_unused; 1206 struct ssb_chipcommon *ssb_cc __maybe_unused; 1207 1208 switch (dev->dev->bus_type) { 1209 #ifdef CONFIG_B43_BCMA 1210 case B43_BUS_BCMA: 1211 bcma_cc = &dev->dev->bdev->bus->drv_cc; 1212 1213 bcma_cc_write32(bcma_cc, BCMA_CC_PMU_CHIPCTL_ADDR, 0); 1214 bcma_cc_mask32(bcma_cc, BCMA_CC_PMU_CHIPCTL_DATA, ~0x4); 1215 bcma_cc_set32(bcma_cc, BCMA_CC_PMU_CHIPCTL_DATA, 0x4); 1216 bcma_cc_mask32(bcma_cc, BCMA_CC_PMU_CHIPCTL_DATA, ~0x4); 1217 break; 1218 #endif 1219 #ifdef CONFIG_B43_SSB 1220 case B43_BUS_SSB: 1221 ssb_cc = &dev->dev->sdev->bus->chipco; 1222 1223 chipco_write32(ssb_cc, SSB_CHIPCO_CHIPCTL_ADDR, 0); 1224 chipco_mask32(ssb_cc, SSB_CHIPCO_CHIPCTL_DATA, ~0x4); 1225 chipco_set32(ssb_cc, SSB_CHIPCO_CHIPCTL_DATA, 0x4); 1226 chipco_mask32(ssb_cc, SSB_CHIPCO_CHIPCTL_DATA, ~0x4); 1227 break; 1228 #endif 1229 } 1230 } 1231 1232 #ifdef CONFIG_B43_BCMA 1233 static void b43_bcma_phy_reset(struct b43_wldev *dev) 1234 { 1235 u32 flags; 1236 1237 /* Put PHY into reset */ 1238 flags = bcma_aread32(dev->dev->bdev, BCMA_IOCTL); 1239 flags |= B43_BCMA_IOCTL_PHY_RESET; 1240 flags |= B43_BCMA_IOCTL_PHY_BW_20MHZ; /* Make 20 MHz def */ 1241 bcma_awrite32(dev->dev->bdev, BCMA_IOCTL, flags); 1242 udelay(2); 1243 1244 b43_phy_take_out_of_reset(dev); 1245 } 1246 1247 static void b43_bcma_wireless_core_reset(struct b43_wldev *dev, bool gmode) 1248 { 1249 u32 req = B43_BCMA_CLKCTLST_80211_PLL_REQ | 1250 B43_BCMA_CLKCTLST_PHY_PLL_REQ; 1251 u32 status = B43_BCMA_CLKCTLST_80211_PLL_ST | 1252 B43_BCMA_CLKCTLST_PHY_PLL_ST; 1253 u32 flags; 1254 1255 flags = B43_BCMA_IOCTL_PHY_CLKEN; 1256 if (gmode) 1257 flags |= B43_BCMA_IOCTL_GMODE; 1258 b43_device_enable(dev, flags); 1259 1260 if (dev->phy.type == B43_PHYTYPE_AC) { 1261 u16 tmp; 1262 1263 tmp = bcma_aread32(dev->dev->bdev, BCMA_IOCTL); 1264 tmp &= ~B43_BCMA_IOCTL_DAC; 1265 tmp |= 0x100; 1266 bcma_awrite32(dev->dev->bdev, BCMA_IOCTL, tmp); 1267 1268 tmp = bcma_aread32(dev->dev->bdev, BCMA_IOCTL); 1269 tmp &= ~B43_BCMA_IOCTL_PHY_CLKEN; 1270 bcma_awrite32(dev->dev->bdev, BCMA_IOCTL, tmp); 1271 1272 tmp = bcma_aread32(dev->dev->bdev, BCMA_IOCTL); 1273 tmp |= B43_BCMA_IOCTL_PHY_CLKEN; 1274 bcma_awrite32(dev->dev->bdev, BCMA_IOCTL, tmp); 1275 } 1276 1277 bcma_core_set_clockmode(dev->dev->bdev, BCMA_CLKMODE_FAST); 1278 b43_bcma_phy_reset(dev); 1279 bcma_core_pll_ctl(dev->dev->bdev, req, status, true); 1280 } 1281 #endif 1282 1283 #ifdef CONFIG_B43_SSB 1284 static void b43_ssb_wireless_core_reset(struct b43_wldev *dev, bool gmode) 1285 { 1286 u32 flags = 0; 1287 1288 if (gmode) 1289 flags |= B43_TMSLOW_GMODE; 1290 flags |= B43_TMSLOW_PHYCLKEN; 1291 flags |= B43_TMSLOW_PHYRESET; 1292 if (dev->phy.type == B43_PHYTYPE_N) 1293 flags |= B43_TMSLOW_PHY_BANDWIDTH_20MHZ; /* Make 20 MHz def */ 1294 b43_device_enable(dev, flags); 1295 msleep(2); /* Wait for the PLL to turn on. */ 1296 1297 b43_phy_take_out_of_reset(dev); 1298 } 1299 #endif 1300 1301 void b43_wireless_core_reset(struct b43_wldev *dev, bool gmode) 1302 { 1303 u32 macctl; 1304 1305 switch (dev->dev->bus_type) { 1306 #ifdef CONFIG_B43_BCMA 1307 case B43_BUS_BCMA: 1308 b43_bcma_wireless_core_reset(dev, gmode); 1309 break; 1310 #endif 1311 #ifdef CONFIG_B43_SSB 1312 case B43_BUS_SSB: 1313 b43_ssb_wireless_core_reset(dev, gmode); 1314 break; 1315 #endif 1316 } 1317 1318 /* Turn Analog ON, but only if we already know the PHY-type. 1319 * This protects against very early setup where we don't know the 1320 * PHY-type, yet. wireless_core_reset will be called once again later, 1321 * when we know the PHY-type. */ 1322 if (dev->phy.ops) 1323 dev->phy.ops->switch_analog(dev, 1); 1324 1325 macctl = b43_read32(dev, B43_MMIO_MACCTL); 1326 macctl &= ~B43_MACCTL_GMODE; 1327 if (gmode) 1328 macctl |= B43_MACCTL_GMODE; 1329 macctl |= B43_MACCTL_IHR_ENABLED; 1330 b43_write32(dev, B43_MMIO_MACCTL, macctl); 1331 } 1332 1333 static void handle_irq_transmit_status(struct b43_wldev *dev) 1334 { 1335 u32 v0, v1; 1336 u16 tmp; 1337 struct b43_txstatus stat; 1338 1339 while (1) { 1340 v0 = b43_read32(dev, B43_MMIO_XMITSTAT_0); 1341 if (!(v0 & 0x00000001)) 1342 break; 1343 v1 = b43_read32(dev, B43_MMIO_XMITSTAT_1); 1344 1345 stat.cookie = (v0 >> 16); 1346 stat.seq = (v1 & 0x0000FFFF); 1347 stat.phy_stat = ((v1 & 0x00FF0000) >> 16); 1348 tmp = (v0 & 0x0000FFFF); 1349 stat.frame_count = ((tmp & 0xF000) >> 12); 1350 stat.rts_count = ((tmp & 0x0F00) >> 8); 1351 stat.supp_reason = ((tmp & 0x001C) >> 2); 1352 stat.pm_indicated = !!(tmp & 0x0080); 1353 stat.intermediate = !!(tmp & 0x0040); 1354 stat.for_ampdu = !!(tmp & 0x0020); 1355 stat.acked = !!(tmp & 0x0002); 1356 1357 b43_handle_txstatus(dev, &stat); 1358 } 1359 } 1360 1361 static void drain_txstatus_queue(struct b43_wldev *dev) 1362 { 1363 u32 dummy; 1364 1365 if (dev->dev->core_rev < 5) 1366 return; 1367 /* Read all entries from the microcode TXstatus FIFO 1368 * and throw them away. 1369 */ 1370 while (1) { 1371 dummy = b43_read32(dev, B43_MMIO_XMITSTAT_0); 1372 if (!(dummy & 0x00000001)) 1373 break; 1374 dummy = b43_read32(dev, B43_MMIO_XMITSTAT_1); 1375 } 1376 } 1377 1378 static u32 b43_jssi_read(struct b43_wldev *dev) 1379 { 1380 u32 val = 0; 1381 1382 val = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_JSSI1); 1383 val <<= 16; 1384 val |= b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_JSSI0); 1385 1386 return val; 1387 } 1388 1389 static void b43_jssi_write(struct b43_wldev *dev, u32 jssi) 1390 { 1391 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_JSSI0, 1392 (jssi & 0x0000FFFF)); 1393 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_JSSI1, 1394 (jssi & 0xFFFF0000) >> 16); 1395 } 1396 1397 static void b43_generate_noise_sample(struct b43_wldev *dev) 1398 { 1399 b43_jssi_write(dev, 0x7F7F7F7F); 1400 b43_write32(dev, B43_MMIO_MACCMD, 1401 b43_read32(dev, B43_MMIO_MACCMD) | B43_MACCMD_BGNOISE); 1402 } 1403 1404 static void b43_calculate_link_quality(struct b43_wldev *dev) 1405 { 1406 /* Top half of Link Quality calculation. */ 1407 1408 if (dev->phy.type != B43_PHYTYPE_G) 1409 return; 1410 if (dev->noisecalc.calculation_running) 1411 return; 1412 dev->noisecalc.calculation_running = true; 1413 dev->noisecalc.nr_samples = 0; 1414 1415 b43_generate_noise_sample(dev); 1416 } 1417 1418 static void handle_irq_noise(struct b43_wldev *dev) 1419 { 1420 struct b43_phy_g *phy = dev->phy.g; 1421 u16 tmp; 1422 u8 noise[4]; 1423 u8 i, j; 1424 s32 average; 1425 1426 /* Bottom half of Link Quality calculation. */ 1427 1428 if (dev->phy.type != B43_PHYTYPE_G) 1429 return; 1430 1431 /* Possible race condition: It might be possible that the user 1432 * changed to a different channel in the meantime since we 1433 * started the calculation. We ignore that fact, since it's 1434 * not really that much of a problem. The background noise is 1435 * an estimation only anyway. Slightly wrong results will get damped 1436 * by the averaging of the 8 sample rounds. Additionally the 1437 * value is shortlived. So it will be replaced by the next noise 1438 * calculation round soon. */ 1439 1440 B43_WARN_ON(!dev->noisecalc.calculation_running); 1441 *((__le32 *)noise) = cpu_to_le32(b43_jssi_read(dev)); 1442 if (noise[0] == 0x7F || noise[1] == 0x7F || 1443 noise[2] == 0x7F || noise[3] == 0x7F) 1444 goto generate_new; 1445 1446 /* Get the noise samples. */ 1447 B43_WARN_ON(dev->noisecalc.nr_samples >= 8); 1448 i = dev->noisecalc.nr_samples; 1449 noise[0] = clamp_val(noise[0], 0, ARRAY_SIZE(phy->nrssi_lt) - 1); 1450 noise[1] = clamp_val(noise[1], 0, ARRAY_SIZE(phy->nrssi_lt) - 1); 1451 noise[2] = clamp_val(noise[2], 0, ARRAY_SIZE(phy->nrssi_lt) - 1); 1452 noise[3] = clamp_val(noise[3], 0, ARRAY_SIZE(phy->nrssi_lt) - 1); 1453 dev->noisecalc.samples[i][0] = phy->nrssi_lt[noise[0]]; 1454 dev->noisecalc.samples[i][1] = phy->nrssi_lt[noise[1]]; 1455 dev->noisecalc.samples[i][2] = phy->nrssi_lt[noise[2]]; 1456 dev->noisecalc.samples[i][3] = phy->nrssi_lt[noise[3]]; 1457 dev->noisecalc.nr_samples++; 1458 if (dev->noisecalc.nr_samples == 8) { 1459 /* Calculate the Link Quality by the noise samples. */ 1460 average = 0; 1461 for (i = 0; i < 8; i++) { 1462 for (j = 0; j < 4; j++) 1463 average += dev->noisecalc.samples[i][j]; 1464 } 1465 average /= (8 * 4); 1466 average *= 125; 1467 average += 64; 1468 average /= 128; 1469 tmp = b43_shm_read16(dev, B43_SHM_SHARED, 0x40C); 1470 tmp = (tmp / 128) & 0x1F; 1471 if (tmp >= 8) 1472 average += 2; 1473 else 1474 average -= 25; 1475 if (tmp == 8) 1476 average -= 72; 1477 else 1478 average -= 48; 1479 1480 dev->stats.link_noise = average; 1481 dev->noisecalc.calculation_running = false; 1482 return; 1483 } 1484 generate_new: 1485 b43_generate_noise_sample(dev); 1486 } 1487 1488 static void handle_irq_tbtt_indication(struct b43_wldev *dev) 1489 { 1490 if (b43_is_mode(dev->wl, NL80211_IFTYPE_AP)) { 1491 ///TODO: PS TBTT 1492 } else { 1493 if (1 /*FIXME: the last PSpoll frame was sent successfully */ ) 1494 b43_power_saving_ctl_bits(dev, 0); 1495 } 1496 if (b43_is_mode(dev->wl, NL80211_IFTYPE_ADHOC)) 1497 dev->dfq_valid = true; 1498 } 1499 1500 static void handle_irq_atim_end(struct b43_wldev *dev) 1501 { 1502 if (dev->dfq_valid) { 1503 b43_write32(dev, B43_MMIO_MACCMD, 1504 b43_read32(dev, B43_MMIO_MACCMD) 1505 | B43_MACCMD_DFQ_VALID); 1506 dev->dfq_valid = false; 1507 } 1508 } 1509 1510 static void handle_irq_pmq(struct b43_wldev *dev) 1511 { 1512 u32 tmp; 1513 1514 //TODO: AP mode. 1515 1516 while (1) { 1517 tmp = b43_read32(dev, B43_MMIO_PS_STATUS); 1518 if (!(tmp & 0x00000008)) 1519 break; 1520 } 1521 /* 16bit write is odd, but correct. */ 1522 b43_write16(dev, B43_MMIO_PS_STATUS, 0x0002); 1523 } 1524 1525 static void b43_write_template_common(struct b43_wldev *dev, 1526 const u8 *data, u16 size, 1527 u16 ram_offset, 1528 u16 shm_size_offset, u8 rate) 1529 { 1530 u32 i, tmp; 1531 struct b43_plcp_hdr4 plcp; 1532 1533 plcp.data = 0; 1534 b43_generate_plcp_hdr(&plcp, size + FCS_LEN, rate); 1535 b43_ram_write(dev, ram_offset, le32_to_cpu(plcp.data)); 1536 ram_offset += sizeof(u32); 1537 /* The PLCP is 6 bytes long, but we only wrote 4 bytes, yet. 1538 * So leave the first two bytes of the next write blank. 1539 */ 1540 tmp = (u32) (data[0]) << 16; 1541 tmp |= (u32) (data[1]) << 24; 1542 b43_ram_write(dev, ram_offset, tmp); 1543 ram_offset += sizeof(u32); 1544 for (i = 2; i < size; i += sizeof(u32)) { 1545 tmp = (u32) (data[i + 0]); 1546 if (i + 1 < size) 1547 tmp |= (u32) (data[i + 1]) << 8; 1548 if (i + 2 < size) 1549 tmp |= (u32) (data[i + 2]) << 16; 1550 if (i + 3 < size) 1551 tmp |= (u32) (data[i + 3]) << 24; 1552 b43_ram_write(dev, ram_offset + i - 2, tmp); 1553 } 1554 b43_shm_write16(dev, B43_SHM_SHARED, shm_size_offset, 1555 size + sizeof(struct b43_plcp_hdr6)); 1556 } 1557 1558 /* Check if the use of the antenna that ieee80211 told us to 1559 * use is possible. This will fall back to DEFAULT. 1560 * "antenna_nr" is the antenna identifier we got from ieee80211. */ 1561 u8 b43_ieee80211_antenna_sanitize(struct b43_wldev *dev, 1562 u8 antenna_nr) 1563 { 1564 u8 antenna_mask; 1565 1566 if (antenna_nr == 0) { 1567 /* Zero means "use default antenna". That's always OK. */ 1568 return 0; 1569 } 1570 1571 /* Get the mask of available antennas. */ 1572 if (dev->phy.gmode) 1573 antenna_mask = dev->dev->bus_sprom->ant_available_bg; 1574 else 1575 antenna_mask = dev->dev->bus_sprom->ant_available_a; 1576 1577 if (!(antenna_mask & (1 << (antenna_nr - 1)))) { 1578 /* This antenna is not available. Fall back to default. */ 1579 return 0; 1580 } 1581 1582 return antenna_nr; 1583 } 1584 1585 /* Convert a b43 antenna number value to the PHY TX control value. */ 1586 static u16 b43_antenna_to_phyctl(int antenna) 1587 { 1588 switch (antenna) { 1589 case B43_ANTENNA0: 1590 return B43_TXH_PHY_ANT0; 1591 case B43_ANTENNA1: 1592 return B43_TXH_PHY_ANT1; 1593 case B43_ANTENNA2: 1594 return B43_TXH_PHY_ANT2; 1595 case B43_ANTENNA3: 1596 return B43_TXH_PHY_ANT3; 1597 case B43_ANTENNA_AUTO0: 1598 case B43_ANTENNA_AUTO1: 1599 return B43_TXH_PHY_ANT01AUTO; 1600 } 1601 B43_WARN_ON(1); 1602 return 0; 1603 } 1604 1605 static void b43_write_beacon_template(struct b43_wldev *dev, 1606 u16 ram_offset, 1607 u16 shm_size_offset) 1608 { 1609 unsigned int i, len, variable_len; 1610 const struct ieee80211_mgmt *bcn; 1611 const u8 *ie; 1612 bool tim_found = false; 1613 unsigned int rate; 1614 u16 ctl; 1615 int antenna; 1616 struct ieee80211_tx_info *info; 1617 unsigned long flags; 1618 struct sk_buff *beacon_skb; 1619 1620 spin_lock_irqsave(&dev->wl->beacon_lock, flags); 1621 info = IEEE80211_SKB_CB(dev->wl->current_beacon); 1622 rate = ieee80211_get_tx_rate(dev->wl->hw, info)->hw_value; 1623 /* Clone the beacon, so it cannot go away, while we write it to hw. */ 1624 beacon_skb = skb_clone(dev->wl->current_beacon, GFP_ATOMIC); 1625 spin_unlock_irqrestore(&dev->wl->beacon_lock, flags); 1626 1627 if (!beacon_skb) { 1628 b43dbg(dev->wl, "Could not upload beacon. " 1629 "Failed to clone beacon skb."); 1630 return; 1631 } 1632 1633 bcn = (const struct ieee80211_mgmt *)(beacon_skb->data); 1634 len = min_t(size_t, beacon_skb->len, 1635 0x200 - sizeof(struct b43_plcp_hdr6)); 1636 1637 b43_write_template_common(dev, (const u8 *)bcn, 1638 len, ram_offset, shm_size_offset, rate); 1639 1640 /* Write the PHY TX control parameters. */ 1641 antenna = B43_ANTENNA_DEFAULT; 1642 antenna = b43_antenna_to_phyctl(antenna); 1643 ctl = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_BEACPHYCTL); 1644 /* We can't send beacons with short preamble. Would get PHY errors. */ 1645 ctl &= ~B43_TXH_PHY_SHORTPRMBL; 1646 ctl &= ~B43_TXH_PHY_ANT; 1647 ctl &= ~B43_TXH_PHY_ENC; 1648 ctl |= antenna; 1649 if (b43_is_cck_rate(rate)) 1650 ctl |= B43_TXH_PHY_ENC_CCK; 1651 else 1652 ctl |= B43_TXH_PHY_ENC_OFDM; 1653 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_BEACPHYCTL, ctl); 1654 1655 /* Find the position of the TIM and the DTIM_period value 1656 * and write them to SHM. */ 1657 ie = bcn->u.beacon.variable; 1658 variable_len = len - offsetof(struct ieee80211_mgmt, u.beacon.variable); 1659 for (i = 0; i < variable_len - 2; ) { 1660 uint8_t ie_id, ie_len; 1661 1662 ie_id = ie[i]; 1663 ie_len = ie[i + 1]; 1664 if (ie_id == 5) { 1665 u16 tim_position; 1666 u16 dtim_period; 1667 /* This is the TIM Information Element */ 1668 1669 /* Check whether the ie_len is in the beacon data range. */ 1670 if (variable_len < ie_len + 2 + i) 1671 break; 1672 /* A valid TIM is at least 4 bytes long. */ 1673 if (ie_len < 4) 1674 break; 1675 tim_found = true; 1676 1677 tim_position = sizeof(struct b43_plcp_hdr6); 1678 tim_position += offsetof(struct ieee80211_mgmt, u.beacon.variable); 1679 tim_position += i; 1680 1681 dtim_period = ie[i + 3]; 1682 1683 b43_shm_write16(dev, B43_SHM_SHARED, 1684 B43_SHM_SH_TIMBPOS, tim_position); 1685 b43_shm_write16(dev, B43_SHM_SHARED, 1686 B43_SHM_SH_DTIMPER, dtim_period); 1687 break; 1688 } 1689 i += ie_len + 2; 1690 } 1691 if (!tim_found) { 1692 /* 1693 * If ucode wants to modify TIM do it behind the beacon, this 1694 * will happen, for example, when doing mesh networking. 1695 */ 1696 b43_shm_write16(dev, B43_SHM_SHARED, 1697 B43_SHM_SH_TIMBPOS, 1698 len + sizeof(struct b43_plcp_hdr6)); 1699 b43_shm_write16(dev, B43_SHM_SHARED, 1700 B43_SHM_SH_DTIMPER, 0); 1701 } 1702 b43dbg(dev->wl, "Updated beacon template at 0x%x\n", ram_offset); 1703 1704 dev_kfree_skb_any(beacon_skb); 1705 } 1706 1707 static void b43_upload_beacon0(struct b43_wldev *dev) 1708 { 1709 struct b43_wl *wl = dev->wl; 1710 1711 if (wl->beacon0_uploaded) 1712 return; 1713 b43_write_beacon_template(dev, B43_SHM_SH_BT_BASE0, B43_SHM_SH_BTL0); 1714 wl->beacon0_uploaded = true; 1715 } 1716 1717 static void b43_upload_beacon1(struct b43_wldev *dev) 1718 { 1719 struct b43_wl *wl = dev->wl; 1720 1721 if (wl->beacon1_uploaded) 1722 return; 1723 b43_write_beacon_template(dev, B43_SHM_SH_BT_BASE1, B43_SHM_SH_BTL1); 1724 wl->beacon1_uploaded = true; 1725 } 1726 1727 static void handle_irq_beacon(struct b43_wldev *dev) 1728 { 1729 struct b43_wl *wl = dev->wl; 1730 u32 cmd, beacon0_valid, beacon1_valid; 1731 1732 if (!b43_is_mode(wl, NL80211_IFTYPE_AP) && 1733 !b43_is_mode(wl, NL80211_IFTYPE_MESH_POINT) && 1734 !b43_is_mode(wl, NL80211_IFTYPE_ADHOC)) 1735 return; 1736 1737 /* This is the bottom half of the asynchronous beacon update. */ 1738 1739 /* Ignore interrupt in the future. */ 1740 dev->irq_mask &= ~B43_IRQ_BEACON; 1741 1742 cmd = b43_read32(dev, B43_MMIO_MACCMD); 1743 beacon0_valid = (cmd & B43_MACCMD_BEACON0_VALID); 1744 beacon1_valid = (cmd & B43_MACCMD_BEACON1_VALID); 1745 1746 /* Schedule interrupt manually, if busy. */ 1747 if (beacon0_valid && beacon1_valid) { 1748 b43_write32(dev, B43_MMIO_GEN_IRQ_REASON, B43_IRQ_BEACON); 1749 dev->irq_mask |= B43_IRQ_BEACON; 1750 return; 1751 } 1752 1753 if (unlikely(wl->beacon_templates_virgin)) { 1754 /* We never uploaded a beacon before. 1755 * Upload both templates now, but only mark one valid. */ 1756 wl->beacon_templates_virgin = false; 1757 b43_upload_beacon0(dev); 1758 b43_upload_beacon1(dev); 1759 cmd = b43_read32(dev, B43_MMIO_MACCMD); 1760 cmd |= B43_MACCMD_BEACON0_VALID; 1761 b43_write32(dev, B43_MMIO_MACCMD, cmd); 1762 } else { 1763 if (!beacon0_valid) { 1764 b43_upload_beacon0(dev); 1765 cmd = b43_read32(dev, B43_MMIO_MACCMD); 1766 cmd |= B43_MACCMD_BEACON0_VALID; 1767 b43_write32(dev, B43_MMIO_MACCMD, cmd); 1768 } else if (!beacon1_valid) { 1769 b43_upload_beacon1(dev); 1770 cmd = b43_read32(dev, B43_MMIO_MACCMD); 1771 cmd |= B43_MACCMD_BEACON1_VALID; 1772 b43_write32(dev, B43_MMIO_MACCMD, cmd); 1773 } 1774 } 1775 } 1776 1777 static void b43_do_beacon_update_trigger_work(struct b43_wldev *dev) 1778 { 1779 u32 old_irq_mask = dev->irq_mask; 1780 1781 /* update beacon right away or defer to irq */ 1782 handle_irq_beacon(dev); 1783 if (old_irq_mask != dev->irq_mask) { 1784 /* The handler updated the IRQ mask. */ 1785 B43_WARN_ON(!dev->irq_mask); 1786 if (b43_read32(dev, B43_MMIO_GEN_IRQ_MASK)) { 1787 b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, dev->irq_mask); 1788 } else { 1789 /* Device interrupts are currently disabled. That means 1790 * we just ran the hardirq handler and scheduled the 1791 * IRQ thread. The thread will write the IRQ mask when 1792 * it finished, so there's nothing to do here. Writing 1793 * the mask _here_ would incorrectly re-enable IRQs. */ 1794 } 1795 } 1796 } 1797 1798 static void b43_beacon_update_trigger_work(struct work_struct *work) 1799 { 1800 struct b43_wl *wl = container_of(work, struct b43_wl, 1801 beacon_update_trigger); 1802 struct b43_wldev *dev; 1803 1804 mutex_lock(&wl->mutex); 1805 dev = wl->current_dev; 1806 if (likely(dev && (b43_status(dev) >= B43_STAT_INITIALIZED))) { 1807 if (b43_bus_host_is_sdio(dev->dev)) { 1808 /* wl->mutex is enough. */ 1809 b43_do_beacon_update_trigger_work(dev); 1810 } else { 1811 spin_lock_irq(&wl->hardirq_lock); 1812 b43_do_beacon_update_trigger_work(dev); 1813 spin_unlock_irq(&wl->hardirq_lock); 1814 } 1815 } 1816 mutex_unlock(&wl->mutex); 1817 } 1818 1819 /* Asynchronously update the packet templates in template RAM. */ 1820 static void b43_update_templates(struct b43_wl *wl) 1821 { 1822 struct sk_buff *beacon, *old_beacon; 1823 unsigned long flags; 1824 1825 /* This is the top half of the asynchronous beacon update. 1826 * The bottom half is the beacon IRQ. 1827 * Beacon update must be asynchronous to avoid sending an 1828 * invalid beacon. This can happen for example, if the firmware 1829 * transmits a beacon while we are updating it. */ 1830 1831 /* We could modify the existing beacon and set the aid bit in 1832 * the TIM field, but that would probably require resizing and 1833 * moving of data within the beacon template. 1834 * Simply request a new beacon and let mac80211 do the hard work. */ 1835 beacon = ieee80211_beacon_get(wl->hw, wl->vif); 1836 if (unlikely(!beacon)) 1837 return; 1838 1839 spin_lock_irqsave(&wl->beacon_lock, flags); 1840 old_beacon = wl->current_beacon; 1841 wl->current_beacon = beacon; 1842 wl->beacon0_uploaded = false; 1843 wl->beacon1_uploaded = false; 1844 spin_unlock_irqrestore(&wl->beacon_lock, flags); 1845 1846 ieee80211_queue_work(wl->hw, &wl->beacon_update_trigger); 1847 1848 if (old_beacon) 1849 dev_kfree_skb_any(old_beacon); 1850 } 1851 1852 static void b43_set_beacon_int(struct b43_wldev *dev, u16 beacon_int) 1853 { 1854 b43_time_lock(dev); 1855 if (dev->dev->core_rev >= 3) { 1856 b43_write32(dev, B43_MMIO_TSF_CFP_REP, (beacon_int << 16)); 1857 b43_write32(dev, B43_MMIO_TSF_CFP_START, (beacon_int << 10)); 1858 } else { 1859 b43_write16(dev, 0x606, (beacon_int >> 6)); 1860 b43_write16(dev, 0x610, beacon_int); 1861 } 1862 b43_time_unlock(dev); 1863 b43dbg(dev->wl, "Set beacon interval to %u\n", beacon_int); 1864 } 1865 1866 static void b43_handle_firmware_panic(struct b43_wldev *dev) 1867 { 1868 u16 reason; 1869 1870 /* Read the register that contains the reason code for the panic. */ 1871 reason = b43_shm_read16(dev, B43_SHM_SCRATCH, B43_FWPANIC_REASON_REG); 1872 b43err(dev->wl, "Whoopsy, firmware panic! Reason: %u\n", reason); 1873 1874 switch (reason) { 1875 default: 1876 b43dbg(dev->wl, "The panic reason is unknown.\n"); 1877 fallthrough; 1878 case B43_FWPANIC_DIE: 1879 /* Do not restart the controller or firmware. 1880 * The device is nonfunctional from now on. 1881 * Restarting would result in this panic to trigger again, 1882 * so we avoid that recursion. */ 1883 break; 1884 case B43_FWPANIC_RESTART: 1885 b43_controller_restart(dev, "Microcode panic"); 1886 break; 1887 } 1888 } 1889 1890 static void handle_irq_ucode_debug(struct b43_wldev *dev) 1891 { 1892 unsigned int i, cnt; 1893 u16 reason, marker_id, marker_line; 1894 __le16 *buf; 1895 1896 /* The proprietary firmware doesn't have this IRQ. */ 1897 if (!dev->fw.opensource) 1898 return; 1899 1900 /* Read the register that contains the reason code for this IRQ. */ 1901 reason = b43_shm_read16(dev, B43_SHM_SCRATCH, B43_DEBUGIRQ_REASON_REG); 1902 1903 switch (reason) { 1904 case B43_DEBUGIRQ_PANIC: 1905 b43_handle_firmware_panic(dev); 1906 break; 1907 case B43_DEBUGIRQ_DUMP_SHM: 1908 if (!B43_DEBUG) 1909 break; /* Only with driver debugging enabled. */ 1910 buf = kmalloc(4096, GFP_ATOMIC); 1911 if (!buf) { 1912 b43dbg(dev->wl, "SHM-dump: Failed to allocate memory\n"); 1913 goto out; 1914 } 1915 for (i = 0; i < 4096; i += 2) { 1916 u16 tmp = b43_shm_read16(dev, B43_SHM_SHARED, i); 1917 buf[i / 2] = cpu_to_le16(tmp); 1918 } 1919 b43info(dev->wl, "Shared memory dump:\n"); 1920 print_hex_dump(KERN_INFO, "", DUMP_PREFIX_OFFSET, 1921 16, 2, buf, 4096, 1); 1922 kfree(buf); 1923 break; 1924 case B43_DEBUGIRQ_DUMP_REGS: 1925 if (!B43_DEBUG) 1926 break; /* Only with driver debugging enabled. */ 1927 b43info(dev->wl, "Microcode register dump:\n"); 1928 for (i = 0, cnt = 0; i < 64; i++) { 1929 u16 tmp = b43_shm_read16(dev, B43_SHM_SCRATCH, i); 1930 if (cnt == 0) 1931 printk(KERN_INFO); 1932 printk("r%02u: 0x%04X ", i, tmp); 1933 cnt++; 1934 if (cnt == 6) { 1935 printk("\n"); 1936 cnt = 0; 1937 } 1938 } 1939 printk("\n"); 1940 break; 1941 case B43_DEBUGIRQ_MARKER: 1942 if (!B43_DEBUG) 1943 break; /* Only with driver debugging enabled. */ 1944 marker_id = b43_shm_read16(dev, B43_SHM_SCRATCH, 1945 B43_MARKER_ID_REG); 1946 marker_line = b43_shm_read16(dev, B43_SHM_SCRATCH, 1947 B43_MARKER_LINE_REG); 1948 b43info(dev->wl, "The firmware just executed the MARKER(%u) " 1949 "at line number %u\n", 1950 marker_id, marker_line); 1951 break; 1952 default: 1953 b43dbg(dev->wl, "Debug-IRQ triggered for unknown reason: %u\n", 1954 reason); 1955 } 1956 out: 1957 /* Acknowledge the debug-IRQ, so the firmware can continue. */ 1958 b43_shm_write16(dev, B43_SHM_SCRATCH, 1959 B43_DEBUGIRQ_REASON_REG, B43_DEBUGIRQ_ACK); 1960 } 1961 1962 static void b43_do_interrupt_thread(struct b43_wldev *dev) 1963 { 1964 u32 reason; 1965 u32 dma_reason[ARRAY_SIZE(dev->dma_reason)]; 1966 u32 merged_dma_reason = 0; 1967 int i; 1968 1969 if (unlikely(b43_status(dev) != B43_STAT_STARTED)) 1970 return; 1971 1972 reason = dev->irq_reason; 1973 for (i = 0; i < ARRAY_SIZE(dma_reason); i++) { 1974 dma_reason[i] = dev->dma_reason[i]; 1975 merged_dma_reason |= dma_reason[i]; 1976 } 1977 1978 if (unlikely(reason & B43_IRQ_MAC_TXERR)) 1979 b43err(dev->wl, "MAC transmission error\n"); 1980 1981 if (unlikely(reason & B43_IRQ_PHY_TXERR)) { 1982 b43err(dev->wl, "PHY transmission error\n"); 1983 rmb(); 1984 if (unlikely(atomic_dec_and_test(&dev->phy.txerr_cnt))) { 1985 atomic_set(&dev->phy.txerr_cnt, 1986 B43_PHY_TX_BADNESS_LIMIT); 1987 b43err(dev->wl, "Too many PHY TX errors, " 1988 "restarting the controller\n"); 1989 b43_controller_restart(dev, "PHY TX errors"); 1990 } 1991 } 1992 1993 if (unlikely(merged_dma_reason & (B43_DMAIRQ_FATALMASK))) { 1994 b43err(dev->wl, 1995 "Fatal DMA error: 0x%08X, 0x%08X, 0x%08X, 0x%08X, 0x%08X, 0x%08X\n", 1996 dma_reason[0], dma_reason[1], 1997 dma_reason[2], dma_reason[3], 1998 dma_reason[4], dma_reason[5]); 1999 b43err(dev->wl, "This device does not support DMA " 2000 "on your system. It will now be switched to PIO.\n"); 2001 /* Fall back to PIO transfers if we get fatal DMA errors! */ 2002 dev->use_pio = true; 2003 b43_controller_restart(dev, "DMA error"); 2004 return; 2005 } 2006 2007 if (unlikely(reason & B43_IRQ_UCODE_DEBUG)) 2008 handle_irq_ucode_debug(dev); 2009 if (reason & B43_IRQ_TBTT_INDI) 2010 handle_irq_tbtt_indication(dev); 2011 if (reason & B43_IRQ_ATIM_END) 2012 handle_irq_atim_end(dev); 2013 if (reason & B43_IRQ_BEACON) 2014 handle_irq_beacon(dev); 2015 if (reason & B43_IRQ_PMQ) 2016 handle_irq_pmq(dev); 2017 if (reason & B43_IRQ_TXFIFO_FLUSH_OK) { 2018 ;/* TODO */ 2019 } 2020 if (reason & B43_IRQ_NOISESAMPLE_OK) 2021 handle_irq_noise(dev); 2022 2023 /* Check the DMA reason registers for received data. */ 2024 if (dma_reason[0] & B43_DMAIRQ_RDESC_UFLOW) { 2025 if (B43_DEBUG) 2026 b43warn(dev->wl, "RX descriptor underrun\n"); 2027 b43_dma_handle_rx_overflow(dev->dma.rx_ring); 2028 } 2029 if (dma_reason[0] & B43_DMAIRQ_RX_DONE) { 2030 if (b43_using_pio_transfers(dev)) 2031 b43_pio_rx(dev->pio.rx_queue); 2032 else 2033 b43_dma_rx(dev->dma.rx_ring); 2034 } 2035 B43_WARN_ON(dma_reason[1] & B43_DMAIRQ_RX_DONE); 2036 B43_WARN_ON(dma_reason[2] & B43_DMAIRQ_RX_DONE); 2037 B43_WARN_ON(dma_reason[3] & B43_DMAIRQ_RX_DONE); 2038 B43_WARN_ON(dma_reason[4] & B43_DMAIRQ_RX_DONE); 2039 B43_WARN_ON(dma_reason[5] & B43_DMAIRQ_RX_DONE); 2040 2041 if (reason & B43_IRQ_TX_OK) 2042 handle_irq_transmit_status(dev); 2043 2044 /* Re-enable interrupts on the device by restoring the current interrupt mask. */ 2045 b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, dev->irq_mask); 2046 2047 #if B43_DEBUG 2048 if (b43_debug(dev, B43_DBG_VERBOSESTATS)) { 2049 dev->irq_count++; 2050 for (i = 0; i < ARRAY_SIZE(dev->irq_bit_count); i++) { 2051 if (reason & (1 << i)) 2052 dev->irq_bit_count[i]++; 2053 } 2054 } 2055 #endif 2056 } 2057 2058 /* Interrupt thread handler. Handles device interrupts in thread context. */ 2059 static irqreturn_t b43_interrupt_thread_handler(int irq, void *dev_id) 2060 { 2061 struct b43_wldev *dev = dev_id; 2062 2063 mutex_lock(&dev->wl->mutex); 2064 b43_do_interrupt_thread(dev); 2065 mutex_unlock(&dev->wl->mutex); 2066 2067 return IRQ_HANDLED; 2068 } 2069 2070 static irqreturn_t b43_do_interrupt(struct b43_wldev *dev) 2071 { 2072 u32 reason; 2073 2074 /* This code runs under wl->hardirq_lock, but _only_ on non-SDIO busses. 2075 * On SDIO, this runs under wl->mutex. */ 2076 2077 reason = b43_read32(dev, B43_MMIO_GEN_IRQ_REASON); 2078 if (reason == 0xffffffff) /* shared IRQ */ 2079 return IRQ_NONE; 2080 reason &= dev->irq_mask; 2081 if (!reason) 2082 return IRQ_NONE; 2083 2084 dev->dma_reason[0] = b43_read32(dev, B43_MMIO_DMA0_REASON) 2085 & 0x0001FC00; 2086 dev->dma_reason[1] = b43_read32(dev, B43_MMIO_DMA1_REASON) 2087 & 0x0000DC00; 2088 dev->dma_reason[2] = b43_read32(dev, B43_MMIO_DMA2_REASON) 2089 & 0x0000DC00; 2090 dev->dma_reason[3] = b43_read32(dev, B43_MMIO_DMA3_REASON) 2091 & 0x0001DC00; 2092 dev->dma_reason[4] = b43_read32(dev, B43_MMIO_DMA4_REASON) 2093 & 0x0000DC00; 2094 /* Unused ring 2095 dev->dma_reason[5] = b43_read32(dev, B43_MMIO_DMA5_REASON) 2096 & 0x0000DC00; 2097 */ 2098 2099 /* ACK the interrupt. */ 2100 b43_write32(dev, B43_MMIO_GEN_IRQ_REASON, reason); 2101 b43_write32(dev, B43_MMIO_DMA0_REASON, dev->dma_reason[0]); 2102 b43_write32(dev, B43_MMIO_DMA1_REASON, dev->dma_reason[1]); 2103 b43_write32(dev, B43_MMIO_DMA2_REASON, dev->dma_reason[2]); 2104 b43_write32(dev, B43_MMIO_DMA3_REASON, dev->dma_reason[3]); 2105 b43_write32(dev, B43_MMIO_DMA4_REASON, dev->dma_reason[4]); 2106 /* Unused ring 2107 b43_write32(dev, B43_MMIO_DMA5_REASON, dev->dma_reason[5]); 2108 */ 2109 2110 /* Disable IRQs on the device. The IRQ thread handler will re-enable them. */ 2111 b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, 0); 2112 /* Save the reason bitmasks for the IRQ thread handler. */ 2113 dev->irq_reason = reason; 2114 2115 return IRQ_WAKE_THREAD; 2116 } 2117 2118 /* Interrupt handler top-half. This runs with interrupts disabled. */ 2119 static irqreturn_t b43_interrupt_handler(int irq, void *dev_id) 2120 { 2121 struct b43_wldev *dev = dev_id; 2122 irqreturn_t ret; 2123 2124 if (unlikely(b43_status(dev) < B43_STAT_STARTED)) 2125 return IRQ_NONE; 2126 2127 spin_lock(&dev->wl->hardirq_lock); 2128 ret = b43_do_interrupt(dev); 2129 spin_unlock(&dev->wl->hardirq_lock); 2130 2131 return ret; 2132 } 2133 2134 /* SDIO interrupt handler. This runs in process context. */ 2135 static void b43_sdio_interrupt_handler(struct b43_wldev *dev) 2136 { 2137 struct b43_wl *wl = dev->wl; 2138 irqreturn_t ret; 2139 2140 mutex_lock(&wl->mutex); 2141 2142 ret = b43_do_interrupt(dev); 2143 if (ret == IRQ_WAKE_THREAD) 2144 b43_do_interrupt_thread(dev); 2145 2146 mutex_unlock(&wl->mutex); 2147 } 2148 2149 void b43_do_release_fw(struct b43_firmware_file *fw) 2150 { 2151 release_firmware(fw->data); 2152 fw->data = NULL; 2153 fw->filename = NULL; 2154 } 2155 2156 static void b43_release_firmware(struct b43_wldev *dev) 2157 { 2158 complete(&dev->fw_load_complete); 2159 b43_do_release_fw(&dev->fw.ucode); 2160 b43_do_release_fw(&dev->fw.pcm); 2161 b43_do_release_fw(&dev->fw.initvals); 2162 b43_do_release_fw(&dev->fw.initvals_band); 2163 } 2164 2165 static void b43_print_fw_helptext(struct b43_wl *wl, bool error) 2166 { 2167 const char text[] = 2168 "You must go to " \ 2169 "https://wireless.wiki.kernel.org/en/users/Drivers/b43#devicefirmware " \ 2170 "and download the correct firmware for this driver version. " \ 2171 "Please carefully read all instructions on this website.\n"; 2172 2173 if (error) 2174 b43err(wl, text); 2175 else 2176 b43warn(wl, text); 2177 } 2178 2179 static void b43_fw_cb(const struct firmware *firmware, void *context) 2180 { 2181 struct b43_request_fw_context *ctx = context; 2182 2183 ctx->blob = firmware; 2184 complete(&ctx->dev->fw_load_complete); 2185 } 2186 2187 int b43_do_request_fw(struct b43_request_fw_context *ctx, 2188 const char *name, 2189 struct b43_firmware_file *fw, bool async) 2190 { 2191 struct b43_fw_header *hdr; 2192 u32 size; 2193 int err; 2194 2195 if (!name) { 2196 /* Don't fetch anything. Free possibly cached firmware. */ 2197 /* FIXME: We should probably keep it anyway, to save some headache 2198 * on suspend/resume with multiband devices. */ 2199 b43_do_release_fw(fw); 2200 return 0; 2201 } 2202 if (fw->filename) { 2203 if ((fw->type == ctx->req_type) && 2204 (strcmp(fw->filename, name) == 0)) 2205 return 0; /* Already have this fw. */ 2206 /* Free the cached firmware first. */ 2207 /* FIXME: We should probably do this later after we successfully 2208 * got the new fw. This could reduce headache with multiband devices. 2209 * We could also redesign this to cache the firmware for all possible 2210 * bands all the time. */ 2211 b43_do_release_fw(fw); 2212 } 2213 2214 switch (ctx->req_type) { 2215 case B43_FWTYPE_PROPRIETARY: 2216 snprintf(ctx->fwname, sizeof(ctx->fwname), 2217 "b43%s/%s.fw", 2218 modparam_fwpostfix, name); 2219 break; 2220 case B43_FWTYPE_OPENSOURCE: 2221 snprintf(ctx->fwname, sizeof(ctx->fwname), 2222 "b43-open%s/%s.fw", 2223 modparam_fwpostfix, name); 2224 break; 2225 default: 2226 B43_WARN_ON(1); 2227 return -ENOSYS; 2228 } 2229 if (async) { 2230 /* do this part asynchronously */ 2231 init_completion(&ctx->dev->fw_load_complete); 2232 err = request_firmware_nowait(THIS_MODULE, 1, ctx->fwname, 2233 ctx->dev->dev->dev, GFP_KERNEL, 2234 ctx, b43_fw_cb); 2235 if (err < 0) { 2236 pr_err("Unable to load firmware\n"); 2237 return err; 2238 } 2239 wait_for_completion(&ctx->dev->fw_load_complete); 2240 if (ctx->blob) 2241 goto fw_ready; 2242 /* On some ARM systems, the async request will fail, but the next sync 2243 * request works. For this reason, we fall through here 2244 */ 2245 } 2246 err = request_firmware(&ctx->blob, ctx->fwname, 2247 ctx->dev->dev->dev); 2248 if (err == -ENOENT) { 2249 snprintf(ctx->errors[ctx->req_type], 2250 sizeof(ctx->errors[ctx->req_type]), 2251 "Firmware file \"%s\" not found\n", 2252 ctx->fwname); 2253 return err; 2254 } else if (err) { 2255 snprintf(ctx->errors[ctx->req_type], 2256 sizeof(ctx->errors[ctx->req_type]), 2257 "Firmware file \"%s\" request failed (err=%d)\n", 2258 ctx->fwname, err); 2259 return err; 2260 } 2261 fw_ready: 2262 if (ctx->blob->size < sizeof(struct b43_fw_header)) 2263 goto err_format; 2264 hdr = (struct b43_fw_header *)(ctx->blob->data); 2265 switch (hdr->type) { 2266 case B43_FW_TYPE_UCODE: 2267 case B43_FW_TYPE_PCM: 2268 size = be32_to_cpu(hdr->size); 2269 if (size != ctx->blob->size - sizeof(struct b43_fw_header)) 2270 goto err_format; 2271 fallthrough; 2272 case B43_FW_TYPE_IV: 2273 if (hdr->ver != 1) 2274 goto err_format; 2275 break; 2276 default: 2277 goto err_format; 2278 } 2279 2280 fw->data = ctx->blob; 2281 fw->filename = name; 2282 fw->type = ctx->req_type; 2283 2284 return 0; 2285 2286 err_format: 2287 snprintf(ctx->errors[ctx->req_type], 2288 sizeof(ctx->errors[ctx->req_type]), 2289 "Firmware file \"%s\" format error.\n", ctx->fwname); 2290 release_firmware(ctx->blob); 2291 2292 return -EPROTO; 2293 } 2294 2295 /* https://bcm-v4.sipsolutions.net/802.11/Init/Firmware */ 2296 static int b43_try_request_fw(struct b43_request_fw_context *ctx) 2297 { 2298 struct b43_wldev *dev = ctx->dev; 2299 struct b43_firmware *fw = &ctx->dev->fw; 2300 struct b43_phy *phy = &dev->phy; 2301 const u8 rev = ctx->dev->dev->core_rev; 2302 const char *filename; 2303 int err; 2304 2305 /* Get microcode */ 2306 filename = NULL; 2307 switch (rev) { 2308 case 42: 2309 if (phy->type == B43_PHYTYPE_AC) 2310 filename = "ucode42"; 2311 break; 2312 case 40: 2313 if (phy->type == B43_PHYTYPE_AC) 2314 filename = "ucode40"; 2315 break; 2316 case 33: 2317 if (phy->type == B43_PHYTYPE_LCN40) 2318 filename = "ucode33_lcn40"; 2319 break; 2320 case 30: 2321 if (phy->type == B43_PHYTYPE_N) 2322 filename = "ucode30_mimo"; 2323 break; 2324 case 29: 2325 if (phy->type == B43_PHYTYPE_HT) 2326 filename = "ucode29_mimo"; 2327 break; 2328 case 26: 2329 if (phy->type == B43_PHYTYPE_HT) 2330 filename = "ucode26_mimo"; 2331 break; 2332 case 28: 2333 case 25: 2334 if (phy->type == B43_PHYTYPE_N) 2335 filename = "ucode25_mimo"; 2336 else if (phy->type == B43_PHYTYPE_LCN) 2337 filename = "ucode25_lcn"; 2338 break; 2339 case 24: 2340 if (phy->type == B43_PHYTYPE_LCN) 2341 filename = "ucode24_lcn"; 2342 break; 2343 case 23: 2344 if (phy->type == B43_PHYTYPE_N) 2345 filename = "ucode16_mimo"; 2346 break; 2347 case 16 ... 19: 2348 if (phy->type == B43_PHYTYPE_N) 2349 filename = "ucode16_mimo"; 2350 else if (phy->type == B43_PHYTYPE_LP) 2351 filename = "ucode16_lp"; 2352 break; 2353 case 15: 2354 filename = "ucode15"; 2355 break; 2356 case 14: 2357 filename = "ucode14"; 2358 break; 2359 case 13: 2360 filename = "ucode13"; 2361 break; 2362 case 11 ... 12: 2363 filename = "ucode11"; 2364 break; 2365 case 5 ... 10: 2366 filename = "ucode5"; 2367 break; 2368 } 2369 if (!filename) 2370 goto err_no_ucode; 2371 err = b43_do_request_fw(ctx, filename, &fw->ucode, true); 2372 if (err) 2373 goto err_load; 2374 2375 /* Get PCM code */ 2376 if ((rev >= 5) && (rev <= 10)) 2377 filename = "pcm5"; 2378 else if (rev >= 11) 2379 filename = NULL; 2380 else 2381 goto err_no_pcm; 2382 fw->pcm_request_failed = false; 2383 err = b43_do_request_fw(ctx, filename, &fw->pcm, false); 2384 if (err == -ENOENT) { 2385 /* We did not find a PCM file? Not fatal, but 2386 * core rev <= 10 must do without hwcrypto then. */ 2387 fw->pcm_request_failed = true; 2388 } else if (err) 2389 goto err_load; 2390 2391 /* Get initvals */ 2392 filename = NULL; 2393 switch (dev->phy.type) { 2394 case B43_PHYTYPE_G: 2395 if (rev == 13) 2396 filename = "b0g0initvals13"; 2397 else if (rev >= 5 && rev <= 10) 2398 filename = "b0g0initvals5"; 2399 break; 2400 case B43_PHYTYPE_N: 2401 if (rev == 30) 2402 filename = "n16initvals30"; 2403 else if (rev == 28 || rev == 25) 2404 filename = "n0initvals25"; 2405 else if (rev == 24) 2406 filename = "n0initvals24"; 2407 else if (rev == 23) 2408 filename = "n0initvals16"; /* What about n0initvals22? */ 2409 else if (rev >= 16 && rev <= 18) 2410 filename = "n0initvals16"; 2411 else if (rev >= 11 && rev <= 12) 2412 filename = "n0initvals11"; 2413 break; 2414 case B43_PHYTYPE_LP: 2415 if (rev >= 16 && rev <= 18) 2416 filename = "lp0initvals16"; 2417 else if (rev == 15) 2418 filename = "lp0initvals15"; 2419 else if (rev == 14) 2420 filename = "lp0initvals14"; 2421 else if (rev == 13) 2422 filename = "lp0initvals13"; 2423 break; 2424 case B43_PHYTYPE_HT: 2425 if (rev == 29) 2426 filename = "ht0initvals29"; 2427 else if (rev == 26) 2428 filename = "ht0initvals26"; 2429 break; 2430 case B43_PHYTYPE_LCN: 2431 if (rev == 24) 2432 filename = "lcn0initvals24"; 2433 break; 2434 case B43_PHYTYPE_LCN40: 2435 if (rev == 33) 2436 filename = "lcn400initvals33"; 2437 break; 2438 case B43_PHYTYPE_AC: 2439 if (rev == 42) 2440 filename = "ac1initvals42"; 2441 else if (rev == 40) 2442 filename = "ac0initvals40"; 2443 break; 2444 } 2445 if (!filename) 2446 goto err_no_initvals; 2447 err = b43_do_request_fw(ctx, filename, &fw->initvals, false); 2448 if (err) 2449 goto err_load; 2450 2451 /* Get bandswitch initvals */ 2452 filename = NULL; 2453 switch (dev->phy.type) { 2454 case B43_PHYTYPE_G: 2455 if (rev == 13) 2456 filename = "b0g0bsinitvals13"; 2457 else if (rev >= 5 && rev <= 10) 2458 filename = "b0g0bsinitvals5"; 2459 break; 2460 case B43_PHYTYPE_N: 2461 if (rev == 30) 2462 filename = "n16bsinitvals30"; 2463 else if (rev == 28 || rev == 25) 2464 filename = "n0bsinitvals25"; 2465 else if (rev == 24) 2466 filename = "n0bsinitvals24"; 2467 else if (rev == 23) 2468 filename = "n0bsinitvals16"; /* What about n0bsinitvals22? */ 2469 else if (rev >= 16 && rev <= 18) 2470 filename = "n0bsinitvals16"; 2471 else if (rev >= 11 && rev <= 12) 2472 filename = "n0bsinitvals11"; 2473 break; 2474 case B43_PHYTYPE_LP: 2475 if (rev >= 16 && rev <= 18) 2476 filename = "lp0bsinitvals16"; 2477 else if (rev == 15) 2478 filename = "lp0bsinitvals15"; 2479 else if (rev == 14) 2480 filename = "lp0bsinitvals14"; 2481 else if (rev == 13) 2482 filename = "lp0bsinitvals13"; 2483 break; 2484 case B43_PHYTYPE_HT: 2485 if (rev == 29) 2486 filename = "ht0bsinitvals29"; 2487 else if (rev == 26) 2488 filename = "ht0bsinitvals26"; 2489 break; 2490 case B43_PHYTYPE_LCN: 2491 if (rev == 24) 2492 filename = "lcn0bsinitvals24"; 2493 break; 2494 case B43_PHYTYPE_LCN40: 2495 if (rev == 33) 2496 filename = "lcn400bsinitvals33"; 2497 break; 2498 case B43_PHYTYPE_AC: 2499 if (rev == 42) 2500 filename = "ac1bsinitvals42"; 2501 else if (rev == 40) 2502 filename = "ac0bsinitvals40"; 2503 break; 2504 } 2505 if (!filename) 2506 goto err_no_initvals; 2507 err = b43_do_request_fw(ctx, filename, &fw->initvals_band, false); 2508 if (err) 2509 goto err_load; 2510 2511 fw->opensource = (ctx->req_type == B43_FWTYPE_OPENSOURCE); 2512 2513 return 0; 2514 2515 err_no_ucode: 2516 err = ctx->fatal_failure = -EOPNOTSUPP; 2517 b43err(dev->wl, "The driver does not know which firmware (ucode) " 2518 "is required for your device (wl-core rev %u)\n", rev); 2519 goto error; 2520 2521 err_no_pcm: 2522 err = ctx->fatal_failure = -EOPNOTSUPP; 2523 b43err(dev->wl, "The driver does not know which firmware (PCM) " 2524 "is required for your device (wl-core rev %u)\n", rev); 2525 goto error; 2526 2527 err_no_initvals: 2528 err = ctx->fatal_failure = -EOPNOTSUPP; 2529 b43err(dev->wl, "The driver does not know which firmware (initvals) " 2530 "is required for your device (wl-core rev %u)\n", rev); 2531 goto error; 2532 2533 err_load: 2534 /* We failed to load this firmware image. The error message 2535 * already is in ctx->errors. Return and let our caller decide 2536 * what to do. */ 2537 goto error; 2538 2539 error: 2540 b43_release_firmware(dev); 2541 return err; 2542 } 2543 2544 static int b43_one_core_attach(struct b43_bus_dev *dev, struct b43_wl *wl); 2545 static void b43_one_core_detach(struct b43_bus_dev *dev); 2546 static int b43_rng_init(struct b43_wl *wl); 2547 2548 static void b43_request_firmware(struct work_struct *work) 2549 { 2550 struct b43_wl *wl = container_of(work, 2551 struct b43_wl, firmware_load); 2552 struct b43_wldev *dev = wl->current_dev; 2553 struct b43_request_fw_context *ctx; 2554 unsigned int i; 2555 int err; 2556 const char *errmsg; 2557 2558 ctx = kzalloc(sizeof(*ctx), GFP_KERNEL); 2559 if (!ctx) 2560 return; 2561 ctx->dev = dev; 2562 2563 ctx->req_type = B43_FWTYPE_PROPRIETARY; 2564 err = b43_try_request_fw(ctx); 2565 if (!err) 2566 goto start_ieee80211; /* Successfully loaded it. */ 2567 /* Was fw version known? */ 2568 if (ctx->fatal_failure) 2569 goto out; 2570 2571 /* proprietary fw not found, try open source */ 2572 ctx->req_type = B43_FWTYPE_OPENSOURCE; 2573 err = b43_try_request_fw(ctx); 2574 if (!err) 2575 goto start_ieee80211; /* Successfully loaded it. */ 2576 if(ctx->fatal_failure) 2577 goto out; 2578 2579 /* Could not find a usable firmware. Print the errors. */ 2580 for (i = 0; i < B43_NR_FWTYPES; i++) { 2581 errmsg = ctx->errors[i]; 2582 if (strlen(errmsg)) 2583 b43err(dev->wl, "%s", errmsg); 2584 } 2585 b43_print_fw_helptext(dev->wl, 1); 2586 goto out; 2587 2588 start_ieee80211: 2589 wl->hw->queues = B43_QOS_QUEUE_NUM; 2590 if (!modparam_qos || dev->fw.opensource) 2591 wl->hw->queues = 1; 2592 2593 err = ieee80211_register_hw(wl->hw); 2594 if (err) 2595 goto out; 2596 wl->hw_registered = true; 2597 b43_leds_register(wl->current_dev); 2598 2599 /* Register HW RNG driver */ 2600 b43_rng_init(wl); 2601 2602 out: 2603 kfree(ctx); 2604 } 2605 2606 static int b43_upload_microcode(struct b43_wldev *dev) 2607 { 2608 struct wiphy *wiphy = dev->wl->hw->wiphy; 2609 const size_t hdr_len = sizeof(struct b43_fw_header); 2610 const __be32 *data; 2611 unsigned int i, len; 2612 u16 fwrev, fwpatch, fwdate, fwtime; 2613 u32 tmp, macctl; 2614 int err = 0; 2615 2616 /* Jump the microcode PSM to offset 0 */ 2617 macctl = b43_read32(dev, B43_MMIO_MACCTL); 2618 B43_WARN_ON(macctl & B43_MACCTL_PSM_RUN); 2619 macctl |= B43_MACCTL_PSM_JMP0; 2620 b43_write32(dev, B43_MMIO_MACCTL, macctl); 2621 /* Zero out all microcode PSM registers and shared memory. */ 2622 for (i = 0; i < 64; i++) 2623 b43_shm_write16(dev, B43_SHM_SCRATCH, i, 0); 2624 for (i = 0; i < 4096; i += 2) 2625 b43_shm_write16(dev, B43_SHM_SHARED, i, 0); 2626 2627 /* Upload Microcode. */ 2628 data = (__be32 *) (dev->fw.ucode.data->data + hdr_len); 2629 len = (dev->fw.ucode.data->size - hdr_len) / sizeof(__be32); 2630 b43_shm_control_word(dev, B43_SHM_UCODE | B43_SHM_AUTOINC_W, 0x0000); 2631 for (i = 0; i < len; i++) { 2632 b43_write32(dev, B43_MMIO_SHM_DATA, be32_to_cpu(data[i])); 2633 udelay(10); 2634 } 2635 2636 if (dev->fw.pcm.data) { 2637 /* Upload PCM data. */ 2638 data = (__be32 *) (dev->fw.pcm.data->data + hdr_len); 2639 len = (dev->fw.pcm.data->size - hdr_len) / sizeof(__be32); 2640 b43_shm_control_word(dev, B43_SHM_HW, 0x01EA); 2641 b43_write32(dev, B43_MMIO_SHM_DATA, 0x00004000); 2642 /* No need for autoinc bit in SHM_HW */ 2643 b43_shm_control_word(dev, B43_SHM_HW, 0x01EB); 2644 for (i = 0; i < len; i++) { 2645 b43_write32(dev, B43_MMIO_SHM_DATA, be32_to_cpu(data[i])); 2646 udelay(10); 2647 } 2648 } 2649 2650 b43_write32(dev, B43_MMIO_GEN_IRQ_REASON, B43_IRQ_ALL); 2651 2652 /* Start the microcode PSM */ 2653 b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_PSM_JMP0, 2654 B43_MACCTL_PSM_RUN); 2655 2656 /* Wait for the microcode to load and respond */ 2657 i = 0; 2658 while (1) { 2659 tmp = b43_read32(dev, B43_MMIO_GEN_IRQ_REASON); 2660 if (tmp == B43_IRQ_MAC_SUSPENDED) 2661 break; 2662 i++; 2663 if (i >= 20) { 2664 b43err(dev->wl, "Microcode not responding\n"); 2665 b43_print_fw_helptext(dev->wl, 1); 2666 err = -ENODEV; 2667 goto error; 2668 } 2669 msleep(50); 2670 } 2671 b43_read32(dev, B43_MMIO_GEN_IRQ_REASON); /* dummy read */ 2672 2673 /* Get and check the revisions. */ 2674 fwrev = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_UCODEREV); 2675 fwpatch = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_UCODEPATCH); 2676 fwdate = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_UCODEDATE); 2677 fwtime = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_UCODETIME); 2678 2679 if (fwrev <= 0x128) { 2680 b43err(dev->wl, "YOUR FIRMWARE IS TOO OLD. Firmware from " 2681 "binary drivers older than version 4.x is unsupported. " 2682 "You must upgrade your firmware files.\n"); 2683 b43_print_fw_helptext(dev->wl, 1); 2684 err = -EOPNOTSUPP; 2685 goto error; 2686 } 2687 dev->fw.rev = fwrev; 2688 dev->fw.patch = fwpatch; 2689 if (dev->fw.rev >= 598) 2690 dev->fw.hdr_format = B43_FW_HDR_598; 2691 else if (dev->fw.rev >= 410) 2692 dev->fw.hdr_format = B43_FW_HDR_410; 2693 else 2694 dev->fw.hdr_format = B43_FW_HDR_351; 2695 WARN_ON(dev->fw.opensource != (fwdate == 0xFFFF)); 2696 2697 dev->qos_enabled = dev->wl->hw->queues > 1; 2698 /* Default to firmware/hardware crypto acceleration. */ 2699 dev->hwcrypto_enabled = true; 2700 2701 if (dev->fw.opensource) { 2702 u16 fwcapa; 2703 2704 /* Patchlevel info is encoded in the "time" field. */ 2705 dev->fw.patch = fwtime; 2706 b43info(dev->wl, "Loading OpenSource firmware version %u.%u\n", 2707 dev->fw.rev, dev->fw.patch); 2708 2709 fwcapa = b43_fwcapa_read(dev); 2710 if (!(fwcapa & B43_FWCAPA_HWCRYPTO) || dev->fw.pcm_request_failed) { 2711 b43info(dev->wl, "Hardware crypto acceleration not supported by firmware\n"); 2712 /* Disable hardware crypto and fall back to software crypto. */ 2713 dev->hwcrypto_enabled = false; 2714 } 2715 /* adding QoS support should use an offline discovery mechanism */ 2716 WARN(fwcapa & B43_FWCAPA_QOS, "QoS in OpenFW not supported\n"); 2717 } else { 2718 b43info(dev->wl, "Loading firmware version %u.%u " 2719 "(20%.2i-%.2i-%.2i %.2i:%.2i:%.2i)\n", 2720 fwrev, fwpatch, 2721 (fwdate >> 12) & 0xF, (fwdate >> 8) & 0xF, fwdate & 0xFF, 2722 (fwtime >> 11) & 0x1F, (fwtime >> 5) & 0x3F, fwtime & 0x1F); 2723 if (dev->fw.pcm_request_failed) { 2724 b43warn(dev->wl, "No \"pcm5.fw\" firmware file found. " 2725 "Hardware accelerated cryptography is disabled.\n"); 2726 b43_print_fw_helptext(dev->wl, 0); 2727 } 2728 } 2729 2730 snprintf(wiphy->fw_version, sizeof(wiphy->fw_version), "%u.%u", 2731 dev->fw.rev, dev->fw.patch); 2732 wiphy->hw_version = dev->dev->core_id; 2733 2734 if (dev->fw.hdr_format == B43_FW_HDR_351) { 2735 /* We're over the deadline, but we keep support for old fw 2736 * until it turns out to be in major conflict with something new. */ 2737 b43warn(dev->wl, "You are using an old firmware image. " 2738 "Support for old firmware will be removed soon " 2739 "(official deadline was July 2008).\n"); 2740 b43_print_fw_helptext(dev->wl, 0); 2741 } 2742 2743 return 0; 2744 2745 error: 2746 /* Stop the microcode PSM. */ 2747 b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_PSM_RUN, 2748 B43_MACCTL_PSM_JMP0); 2749 2750 return err; 2751 } 2752 2753 static int b43_write_initvals(struct b43_wldev *dev, 2754 const struct b43_iv *ivals, 2755 size_t count, 2756 size_t array_size) 2757 { 2758 const struct b43_iv *iv; 2759 u16 offset; 2760 size_t i; 2761 bool bit32; 2762 2763 BUILD_BUG_ON(sizeof(struct b43_iv) != 6); 2764 iv = ivals; 2765 for (i = 0; i < count; i++) { 2766 if (array_size < sizeof(iv->offset_size)) 2767 goto err_format; 2768 array_size -= sizeof(iv->offset_size); 2769 offset = be16_to_cpu(iv->offset_size); 2770 bit32 = !!(offset & B43_IV_32BIT); 2771 offset &= B43_IV_OFFSET_MASK; 2772 if (offset >= 0x1000) 2773 goto err_format; 2774 if (bit32) { 2775 u32 value; 2776 2777 if (array_size < sizeof(iv->data.d32)) 2778 goto err_format; 2779 array_size -= sizeof(iv->data.d32); 2780 2781 value = get_unaligned_be32(&iv->data.d32); 2782 b43_write32(dev, offset, value); 2783 2784 iv = (const struct b43_iv *)((const uint8_t *)iv + 2785 sizeof(__be16) + 2786 sizeof(__be32)); 2787 } else { 2788 u16 value; 2789 2790 if (array_size < sizeof(iv->data.d16)) 2791 goto err_format; 2792 array_size -= sizeof(iv->data.d16); 2793 2794 value = be16_to_cpu(iv->data.d16); 2795 b43_write16(dev, offset, value); 2796 2797 iv = (const struct b43_iv *)((const uint8_t *)iv + 2798 sizeof(__be16) + 2799 sizeof(__be16)); 2800 } 2801 } 2802 if (array_size) 2803 goto err_format; 2804 2805 return 0; 2806 2807 err_format: 2808 b43err(dev->wl, "Initial Values Firmware file-format error.\n"); 2809 b43_print_fw_helptext(dev->wl, 1); 2810 2811 return -EPROTO; 2812 } 2813 2814 static int b43_upload_initvals(struct b43_wldev *dev) 2815 { 2816 const size_t hdr_len = sizeof(struct b43_fw_header); 2817 const struct b43_fw_header *hdr; 2818 struct b43_firmware *fw = &dev->fw; 2819 const struct b43_iv *ivals; 2820 size_t count; 2821 2822 hdr = (const struct b43_fw_header *)(fw->initvals.data->data); 2823 ivals = (const struct b43_iv *)(fw->initvals.data->data + hdr_len); 2824 count = be32_to_cpu(hdr->size); 2825 return b43_write_initvals(dev, ivals, count, 2826 fw->initvals.data->size - hdr_len); 2827 } 2828 2829 static int b43_upload_initvals_band(struct b43_wldev *dev) 2830 { 2831 const size_t hdr_len = sizeof(struct b43_fw_header); 2832 const struct b43_fw_header *hdr; 2833 struct b43_firmware *fw = &dev->fw; 2834 const struct b43_iv *ivals; 2835 size_t count; 2836 2837 if (!fw->initvals_band.data) 2838 return 0; 2839 2840 hdr = (const struct b43_fw_header *)(fw->initvals_band.data->data); 2841 ivals = (const struct b43_iv *)(fw->initvals_band.data->data + hdr_len); 2842 count = be32_to_cpu(hdr->size); 2843 return b43_write_initvals(dev, ivals, count, 2844 fw->initvals_band.data->size - hdr_len); 2845 } 2846 2847 /* Initialize the GPIOs 2848 * https://bcm-specs.sipsolutions.net/GPIO 2849 */ 2850 2851 #ifdef CONFIG_B43_SSB 2852 static struct ssb_device *b43_ssb_gpio_dev(struct b43_wldev *dev) 2853 { 2854 struct ssb_bus *bus = dev->dev->sdev->bus; 2855 2856 #ifdef CONFIG_SSB_DRIVER_PCICORE 2857 return (bus->chipco.dev ? bus->chipco.dev : bus->pcicore.dev); 2858 #else 2859 return bus->chipco.dev; 2860 #endif 2861 } 2862 #endif 2863 2864 static int b43_gpio_init(struct b43_wldev *dev) 2865 { 2866 #ifdef CONFIG_B43_SSB 2867 struct ssb_device *gpiodev; 2868 #endif 2869 u32 mask, set; 2870 2871 b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_GPOUTSMSK, 0); 2872 b43_maskset16(dev, B43_MMIO_GPIO_MASK, ~0, 0xF); 2873 2874 mask = 0x0000001F; 2875 set = 0x0000000F; 2876 if (dev->dev->chip_id == 0x4301) { 2877 mask |= 0x0060; 2878 set |= 0x0060; 2879 } else if (dev->dev->chip_id == 0x5354) { 2880 /* Don't allow overtaking buttons GPIOs */ 2881 set &= 0x2; /* 0x2 is LED GPIO on BCM5354 */ 2882 } 2883 2884 if (0 /* FIXME: conditional unknown */ ) { 2885 b43_write16(dev, B43_MMIO_GPIO_MASK, 2886 b43_read16(dev, B43_MMIO_GPIO_MASK) 2887 | 0x0100); 2888 /* BT Coexistance Input */ 2889 mask |= 0x0080; 2890 set |= 0x0080; 2891 /* BT Coexistance Out */ 2892 mask |= 0x0100; 2893 set |= 0x0100; 2894 } 2895 if (dev->dev->bus_sprom->boardflags_lo & B43_BFL_PACTRL) { 2896 /* PA is controlled by gpio 9, let ucode handle it */ 2897 b43_write16(dev, B43_MMIO_GPIO_MASK, 2898 b43_read16(dev, B43_MMIO_GPIO_MASK) 2899 | 0x0200); 2900 mask |= 0x0200; 2901 set |= 0x0200; 2902 } 2903 2904 switch (dev->dev->bus_type) { 2905 #ifdef CONFIG_B43_BCMA 2906 case B43_BUS_BCMA: 2907 bcma_chipco_gpio_control(&dev->dev->bdev->bus->drv_cc, mask, set); 2908 break; 2909 #endif 2910 #ifdef CONFIG_B43_SSB 2911 case B43_BUS_SSB: 2912 gpiodev = b43_ssb_gpio_dev(dev); 2913 if (gpiodev) 2914 ssb_write32(gpiodev, B43_GPIO_CONTROL, 2915 (ssb_read32(gpiodev, B43_GPIO_CONTROL) 2916 & ~mask) | set); 2917 break; 2918 #endif 2919 } 2920 2921 return 0; 2922 } 2923 2924 /* Turn off all GPIO stuff. Call this on module unload, for example. */ 2925 static void b43_gpio_cleanup(struct b43_wldev *dev) 2926 { 2927 #ifdef CONFIG_B43_SSB 2928 struct ssb_device *gpiodev; 2929 #endif 2930 2931 switch (dev->dev->bus_type) { 2932 #ifdef CONFIG_B43_BCMA 2933 case B43_BUS_BCMA: 2934 bcma_chipco_gpio_control(&dev->dev->bdev->bus->drv_cc, ~0, 0); 2935 break; 2936 #endif 2937 #ifdef CONFIG_B43_SSB 2938 case B43_BUS_SSB: 2939 gpiodev = b43_ssb_gpio_dev(dev); 2940 if (gpiodev) 2941 ssb_write32(gpiodev, B43_GPIO_CONTROL, 0); 2942 break; 2943 #endif 2944 } 2945 } 2946 2947 /* http://bcm-specs.sipsolutions.net/EnableMac */ 2948 void b43_mac_enable(struct b43_wldev *dev) 2949 { 2950 if (b43_debug(dev, B43_DBG_FIRMWARE)) { 2951 u16 fwstate; 2952 2953 fwstate = b43_shm_read16(dev, B43_SHM_SHARED, 2954 B43_SHM_SH_UCODESTAT); 2955 if ((fwstate != B43_SHM_SH_UCODESTAT_SUSP) && 2956 (fwstate != B43_SHM_SH_UCODESTAT_SLEEP)) { 2957 b43err(dev->wl, "b43_mac_enable(): The firmware " 2958 "should be suspended, but current state is %u\n", 2959 fwstate); 2960 } 2961 } 2962 2963 dev->mac_suspended--; 2964 B43_WARN_ON(dev->mac_suspended < 0); 2965 if (dev->mac_suspended == 0) { 2966 b43_maskset32(dev, B43_MMIO_MACCTL, ~0, B43_MACCTL_ENABLED); 2967 b43_write32(dev, B43_MMIO_GEN_IRQ_REASON, 2968 B43_IRQ_MAC_SUSPENDED); 2969 /* Commit writes */ 2970 b43_read32(dev, B43_MMIO_MACCTL); 2971 b43_read32(dev, B43_MMIO_GEN_IRQ_REASON); 2972 b43_power_saving_ctl_bits(dev, 0); 2973 } 2974 } 2975 2976 /* https://bcm-specs.sipsolutions.net/SuspendMAC */ 2977 void b43_mac_suspend(struct b43_wldev *dev) 2978 { 2979 int i; 2980 u32 tmp; 2981 2982 might_sleep(); 2983 B43_WARN_ON(dev->mac_suspended < 0); 2984 2985 if (dev->mac_suspended == 0) { 2986 b43_power_saving_ctl_bits(dev, B43_PS_AWAKE); 2987 b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_ENABLED, 0); 2988 /* force pci to flush the write */ 2989 b43_read32(dev, B43_MMIO_MACCTL); 2990 for (i = 35; i; i--) { 2991 tmp = b43_read32(dev, B43_MMIO_GEN_IRQ_REASON); 2992 if (tmp & B43_IRQ_MAC_SUSPENDED) 2993 goto out; 2994 udelay(10); 2995 } 2996 /* Hm, it seems this will take some time. Use msleep(). */ 2997 for (i = 40; i; i--) { 2998 tmp = b43_read32(dev, B43_MMIO_GEN_IRQ_REASON); 2999 if (tmp & B43_IRQ_MAC_SUSPENDED) 3000 goto out; 3001 msleep(1); 3002 } 3003 b43err(dev->wl, "MAC suspend failed\n"); 3004 } 3005 out: 3006 dev->mac_suspended++; 3007 } 3008 3009 /* https://bcm-v4.sipsolutions.net/802.11/PHY/N/MacPhyClkSet */ 3010 void b43_mac_phy_clock_set(struct b43_wldev *dev, bool on) 3011 { 3012 u32 tmp; 3013 3014 switch (dev->dev->bus_type) { 3015 #ifdef CONFIG_B43_BCMA 3016 case B43_BUS_BCMA: 3017 tmp = bcma_aread32(dev->dev->bdev, BCMA_IOCTL); 3018 if (on) 3019 tmp |= B43_BCMA_IOCTL_MACPHYCLKEN; 3020 else 3021 tmp &= ~B43_BCMA_IOCTL_MACPHYCLKEN; 3022 bcma_awrite32(dev->dev->bdev, BCMA_IOCTL, tmp); 3023 break; 3024 #endif 3025 #ifdef CONFIG_B43_SSB 3026 case B43_BUS_SSB: 3027 tmp = ssb_read32(dev->dev->sdev, SSB_TMSLOW); 3028 if (on) 3029 tmp |= B43_TMSLOW_MACPHYCLKEN; 3030 else 3031 tmp &= ~B43_TMSLOW_MACPHYCLKEN; 3032 ssb_write32(dev->dev->sdev, SSB_TMSLOW, tmp); 3033 break; 3034 #endif 3035 } 3036 } 3037 3038 /* brcms_b_switch_macfreq */ 3039 void b43_mac_switch_freq(struct b43_wldev *dev, u8 spurmode) 3040 { 3041 u16 chip_id = dev->dev->chip_id; 3042 3043 if (chip_id == BCMA_CHIP_ID_BCM4331) { 3044 switch (spurmode) { 3045 case 2: /* 168 Mhz: 2^26/168 = 0x61862 */ 3046 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0x1862); 3047 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0x6); 3048 break; 3049 case 1: /* 164 Mhz: 2^26/164 = 0x63e70 */ 3050 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0x3e70); 3051 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0x6); 3052 break; 3053 default: /* 160 Mhz: 2^26/160 = 0x66666 */ 3054 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0x6666); 3055 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0x6); 3056 break; 3057 } 3058 } else if (chip_id == BCMA_CHIP_ID_BCM43131 || 3059 chip_id == BCMA_CHIP_ID_BCM43217 || 3060 chip_id == BCMA_CHIP_ID_BCM43222 || 3061 chip_id == BCMA_CHIP_ID_BCM43224 || 3062 chip_id == BCMA_CHIP_ID_BCM43225 || 3063 chip_id == BCMA_CHIP_ID_BCM43227 || 3064 chip_id == BCMA_CHIP_ID_BCM43228) { 3065 switch (spurmode) { 3066 case 2: /* 126 Mhz */ 3067 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0x2082); 3068 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0x8); 3069 break; 3070 case 1: /* 123 Mhz */ 3071 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0x5341); 3072 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0x8); 3073 break; 3074 default: /* 120 Mhz */ 3075 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0x8889); 3076 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0x8); 3077 break; 3078 } 3079 } else if (dev->phy.type == B43_PHYTYPE_LCN) { 3080 switch (spurmode) { 3081 case 1: /* 82 Mhz */ 3082 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0x7CE0); 3083 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0xC); 3084 break; 3085 default: /* 80 Mhz */ 3086 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0xCCCD); 3087 b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0xC); 3088 break; 3089 } 3090 } 3091 } 3092 3093 static void b43_adjust_opmode(struct b43_wldev *dev) 3094 { 3095 struct b43_wl *wl = dev->wl; 3096 u32 ctl; 3097 u16 cfp_pretbtt; 3098 3099 ctl = b43_read32(dev, B43_MMIO_MACCTL); 3100 /* Reset status to STA infrastructure mode. */ 3101 ctl &= ~B43_MACCTL_AP; 3102 ctl &= ~B43_MACCTL_KEEP_CTL; 3103 ctl &= ~B43_MACCTL_KEEP_BADPLCP; 3104 ctl &= ~B43_MACCTL_KEEP_BAD; 3105 ctl &= ~B43_MACCTL_PROMISC; 3106 ctl &= ~B43_MACCTL_BEACPROMISC; 3107 ctl |= B43_MACCTL_INFRA; 3108 3109 if (b43_is_mode(wl, NL80211_IFTYPE_AP) || 3110 b43_is_mode(wl, NL80211_IFTYPE_MESH_POINT)) 3111 ctl |= B43_MACCTL_AP; 3112 else if (b43_is_mode(wl, NL80211_IFTYPE_ADHOC)) 3113 ctl &= ~B43_MACCTL_INFRA; 3114 3115 if (wl->filter_flags & FIF_CONTROL) 3116 ctl |= B43_MACCTL_KEEP_CTL; 3117 if (wl->filter_flags & FIF_FCSFAIL) 3118 ctl |= B43_MACCTL_KEEP_BAD; 3119 if (wl->filter_flags & FIF_PLCPFAIL) 3120 ctl |= B43_MACCTL_KEEP_BADPLCP; 3121 if (wl->filter_flags & FIF_BCN_PRBRESP_PROMISC) 3122 ctl |= B43_MACCTL_BEACPROMISC; 3123 3124 /* Workaround: On old hardware the HW-MAC-address-filter 3125 * doesn't work properly, so always run promisc in filter 3126 * it in software. */ 3127 if (dev->dev->core_rev <= 4) 3128 ctl |= B43_MACCTL_PROMISC; 3129 3130 b43_write32(dev, B43_MMIO_MACCTL, ctl); 3131 3132 cfp_pretbtt = 2; 3133 if ((ctl & B43_MACCTL_INFRA) && !(ctl & B43_MACCTL_AP)) { 3134 if (dev->dev->chip_id == 0x4306 && 3135 dev->dev->chip_rev == 3) 3136 cfp_pretbtt = 100; 3137 else 3138 cfp_pretbtt = 50; 3139 } 3140 b43_write16(dev, 0x612, cfp_pretbtt); 3141 3142 /* FIXME: We don't currently implement the PMQ mechanism, 3143 * so always disable it. If we want to implement PMQ, 3144 * we need to enable it here (clear DISCPMQ) in AP mode. 3145 */ 3146 if (0 /* ctl & B43_MACCTL_AP */) 3147 b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_DISCPMQ, 0); 3148 else 3149 b43_maskset32(dev, B43_MMIO_MACCTL, ~0, B43_MACCTL_DISCPMQ); 3150 } 3151 3152 static void b43_rate_memory_write(struct b43_wldev *dev, u16 rate, int is_ofdm) 3153 { 3154 u16 offset; 3155 3156 if (is_ofdm) { 3157 offset = 0x480; 3158 offset += (b43_plcp_get_ratecode_ofdm(rate) & 0x000F) * 2; 3159 } else { 3160 offset = 0x4C0; 3161 offset += (b43_plcp_get_ratecode_cck(rate) & 0x000F) * 2; 3162 } 3163 b43_shm_write16(dev, B43_SHM_SHARED, offset + 0x20, 3164 b43_shm_read16(dev, B43_SHM_SHARED, offset)); 3165 } 3166 3167 static void b43_rate_memory_init(struct b43_wldev *dev) 3168 { 3169 switch (dev->phy.type) { 3170 case B43_PHYTYPE_G: 3171 case B43_PHYTYPE_N: 3172 case B43_PHYTYPE_LP: 3173 case B43_PHYTYPE_HT: 3174 case B43_PHYTYPE_LCN: 3175 b43_rate_memory_write(dev, B43_OFDM_RATE_6MB, 1); 3176 b43_rate_memory_write(dev, B43_OFDM_RATE_9MB, 1); 3177 b43_rate_memory_write(dev, B43_OFDM_RATE_12MB, 1); 3178 b43_rate_memory_write(dev, B43_OFDM_RATE_18MB, 1); 3179 b43_rate_memory_write(dev, B43_OFDM_RATE_24MB, 1); 3180 b43_rate_memory_write(dev, B43_OFDM_RATE_36MB, 1); 3181 b43_rate_memory_write(dev, B43_OFDM_RATE_48MB, 1); 3182 b43_rate_memory_write(dev, B43_OFDM_RATE_54MB, 1); 3183 fallthrough; 3184 case B43_PHYTYPE_B: 3185 b43_rate_memory_write(dev, B43_CCK_RATE_1MB, 0); 3186 b43_rate_memory_write(dev, B43_CCK_RATE_2MB, 0); 3187 b43_rate_memory_write(dev, B43_CCK_RATE_5MB, 0); 3188 b43_rate_memory_write(dev, B43_CCK_RATE_11MB, 0); 3189 break; 3190 default: 3191 B43_WARN_ON(1); 3192 } 3193 } 3194 3195 /* Set the default values for the PHY TX Control Words. */ 3196 static void b43_set_phytxctl_defaults(struct b43_wldev *dev) 3197 { 3198 u16 ctl = 0; 3199 3200 ctl |= B43_TXH_PHY_ENC_CCK; 3201 ctl |= B43_TXH_PHY_ANT01AUTO; 3202 ctl |= B43_TXH_PHY_TXPWR; 3203 3204 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_BEACPHYCTL, ctl); 3205 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_ACKCTSPHYCTL, ctl); 3206 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_PRPHYCTL, ctl); 3207 } 3208 3209 /* Set the TX-Antenna for management frames sent by firmware. */ 3210 static void b43_mgmtframe_txantenna(struct b43_wldev *dev, int antenna) 3211 { 3212 u16 ant; 3213 u16 tmp; 3214 3215 ant = b43_antenna_to_phyctl(antenna); 3216 3217 /* For ACK/CTS */ 3218 tmp = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_ACKCTSPHYCTL); 3219 tmp = (tmp & ~B43_TXH_PHY_ANT) | ant; 3220 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_ACKCTSPHYCTL, tmp); 3221 /* For Probe Resposes */ 3222 tmp = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_PRPHYCTL); 3223 tmp = (tmp & ~B43_TXH_PHY_ANT) | ant; 3224 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_PRPHYCTL, tmp); 3225 } 3226 3227 /* This is the opposite of b43_chip_init() */ 3228 static void b43_chip_exit(struct b43_wldev *dev) 3229 { 3230 b43_phy_exit(dev); 3231 b43_gpio_cleanup(dev); 3232 /* firmware is released later */ 3233 } 3234 3235 /* Initialize the chip 3236 * https://bcm-specs.sipsolutions.net/ChipInit 3237 */ 3238 static int b43_chip_init(struct b43_wldev *dev) 3239 { 3240 struct b43_phy *phy = &dev->phy; 3241 int err; 3242 u32 macctl; 3243 u16 value16; 3244 3245 /* Initialize the MAC control */ 3246 macctl = B43_MACCTL_IHR_ENABLED | B43_MACCTL_SHM_ENABLED; 3247 if (dev->phy.gmode) 3248 macctl |= B43_MACCTL_GMODE; 3249 macctl |= B43_MACCTL_INFRA; 3250 b43_write32(dev, B43_MMIO_MACCTL, macctl); 3251 3252 err = b43_upload_microcode(dev); 3253 if (err) 3254 goto out; /* firmware is released later */ 3255 3256 err = b43_gpio_init(dev); 3257 if (err) 3258 goto out; /* firmware is released later */ 3259 3260 err = b43_upload_initvals(dev); 3261 if (err) 3262 goto err_gpio_clean; 3263 3264 err = b43_upload_initvals_band(dev); 3265 if (err) 3266 goto err_gpio_clean; 3267 3268 /* Turn the Analog on and initialize the PHY. */ 3269 phy->ops->switch_analog(dev, 1); 3270 err = b43_phy_init(dev); 3271 if (err) 3272 goto err_gpio_clean; 3273 3274 /* Disable Interference Mitigation. */ 3275 if (phy->ops->interf_mitigation) 3276 phy->ops->interf_mitigation(dev, B43_INTERFMODE_NONE); 3277 3278 /* Select the antennae */ 3279 if (phy->ops->set_rx_antenna) 3280 phy->ops->set_rx_antenna(dev, B43_ANTENNA_DEFAULT); 3281 b43_mgmtframe_txantenna(dev, B43_ANTENNA_DEFAULT); 3282 3283 if (phy->type == B43_PHYTYPE_B) { 3284 value16 = b43_read16(dev, 0x005E); 3285 value16 |= 0x0004; 3286 b43_write16(dev, 0x005E, value16); 3287 } 3288 b43_write32(dev, 0x0100, 0x01000000); 3289 if (dev->dev->core_rev < 5) 3290 b43_write32(dev, 0x010C, 0x01000000); 3291 3292 b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_INFRA, 0); 3293 b43_maskset32(dev, B43_MMIO_MACCTL, ~0, B43_MACCTL_INFRA); 3294 3295 /* Probe Response Timeout value */ 3296 /* FIXME: Default to 0, has to be set by ioctl probably... :-/ */ 3297 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_PRMAXTIME, 0); 3298 3299 /* Initially set the wireless operation mode. */ 3300 b43_adjust_opmode(dev); 3301 3302 if (dev->dev->core_rev < 3) { 3303 b43_write16(dev, 0x060E, 0x0000); 3304 b43_write16(dev, 0x0610, 0x8000); 3305 b43_write16(dev, 0x0604, 0x0000); 3306 b43_write16(dev, 0x0606, 0x0200); 3307 } else { 3308 b43_write32(dev, 0x0188, 0x80000000); 3309 b43_write32(dev, 0x018C, 0x02000000); 3310 } 3311 b43_write32(dev, B43_MMIO_GEN_IRQ_REASON, 0x00004000); 3312 b43_write32(dev, B43_MMIO_DMA0_IRQ_MASK, 0x0001FC00); 3313 b43_write32(dev, B43_MMIO_DMA1_IRQ_MASK, 0x0000DC00); 3314 b43_write32(dev, B43_MMIO_DMA2_IRQ_MASK, 0x0000DC00); 3315 b43_write32(dev, B43_MMIO_DMA3_IRQ_MASK, 0x0001DC00); 3316 b43_write32(dev, B43_MMIO_DMA4_IRQ_MASK, 0x0000DC00); 3317 b43_write32(dev, B43_MMIO_DMA5_IRQ_MASK, 0x0000DC00); 3318 3319 b43_mac_phy_clock_set(dev, true); 3320 3321 switch (dev->dev->bus_type) { 3322 #ifdef CONFIG_B43_BCMA 3323 case B43_BUS_BCMA: 3324 /* FIXME: 0xE74 is quite common, but should be read from CC */ 3325 b43_write16(dev, B43_MMIO_POWERUP_DELAY, 0xE74); 3326 break; 3327 #endif 3328 #ifdef CONFIG_B43_SSB 3329 case B43_BUS_SSB: 3330 b43_write16(dev, B43_MMIO_POWERUP_DELAY, 3331 dev->dev->sdev->bus->chipco.fast_pwrup_delay); 3332 break; 3333 #endif 3334 } 3335 3336 err = 0; 3337 b43dbg(dev->wl, "Chip initialized\n"); 3338 out: 3339 return err; 3340 3341 err_gpio_clean: 3342 b43_gpio_cleanup(dev); 3343 return err; 3344 } 3345 3346 static void b43_periodic_every60sec(struct b43_wldev *dev) 3347 { 3348 const struct b43_phy_operations *ops = dev->phy.ops; 3349 3350 if (ops->pwork_60sec) 3351 ops->pwork_60sec(dev); 3352 3353 /* Force check the TX power emission now. */ 3354 b43_phy_txpower_check(dev, B43_TXPWR_IGNORE_TIME); 3355 } 3356 3357 static void b43_periodic_every30sec(struct b43_wldev *dev) 3358 { 3359 /* Update device statistics. */ 3360 b43_calculate_link_quality(dev); 3361 } 3362 3363 static void b43_periodic_every15sec(struct b43_wldev *dev) 3364 { 3365 struct b43_phy *phy = &dev->phy; 3366 u16 wdr; 3367 3368 if (dev->fw.opensource) { 3369 /* Check if the firmware is still alive. 3370 * It will reset the watchdog counter to 0 in its idle loop. */ 3371 wdr = b43_shm_read16(dev, B43_SHM_SCRATCH, B43_WATCHDOG_REG); 3372 if (unlikely(wdr)) { 3373 b43err(dev->wl, "Firmware watchdog: The firmware died!\n"); 3374 b43_controller_restart(dev, "Firmware watchdog"); 3375 return; 3376 } else { 3377 b43_shm_write16(dev, B43_SHM_SCRATCH, 3378 B43_WATCHDOG_REG, 1); 3379 } 3380 } 3381 3382 if (phy->ops->pwork_15sec) 3383 phy->ops->pwork_15sec(dev); 3384 3385 atomic_set(&phy->txerr_cnt, B43_PHY_TX_BADNESS_LIMIT); 3386 wmb(); 3387 3388 #if B43_DEBUG 3389 if (b43_debug(dev, B43_DBG_VERBOSESTATS)) { 3390 unsigned int i; 3391 3392 b43dbg(dev->wl, "Stats: %7u IRQs/sec, %7u TX/sec, %7u RX/sec\n", 3393 dev->irq_count / 15, 3394 dev->tx_count / 15, 3395 dev->rx_count / 15); 3396 dev->irq_count = 0; 3397 dev->tx_count = 0; 3398 dev->rx_count = 0; 3399 for (i = 0; i < ARRAY_SIZE(dev->irq_bit_count); i++) { 3400 if (dev->irq_bit_count[i]) { 3401 b43dbg(dev->wl, "Stats: %7u IRQ-%02u/sec (0x%08X)\n", 3402 dev->irq_bit_count[i] / 15, i, (1 << i)); 3403 dev->irq_bit_count[i] = 0; 3404 } 3405 } 3406 } 3407 #endif 3408 } 3409 3410 static void do_periodic_work(struct b43_wldev *dev) 3411 { 3412 unsigned int state; 3413 3414 state = dev->periodic_state; 3415 if (state % 4 == 0) 3416 b43_periodic_every60sec(dev); 3417 if (state % 2 == 0) 3418 b43_periodic_every30sec(dev); 3419 b43_periodic_every15sec(dev); 3420 } 3421 3422 /* Periodic work locking policy: 3423 * The whole periodic work handler is protected by 3424 * wl->mutex. If another lock is needed somewhere in the 3425 * pwork callchain, it's acquired in-place, where it's needed. 3426 */ 3427 static void b43_periodic_work_handler(struct work_struct *work) 3428 { 3429 struct b43_wldev *dev = container_of(work, struct b43_wldev, 3430 periodic_work.work); 3431 struct b43_wl *wl = dev->wl; 3432 unsigned long delay; 3433 3434 mutex_lock(&wl->mutex); 3435 3436 if (unlikely(b43_status(dev) != B43_STAT_STARTED)) 3437 goto out; 3438 if (b43_debug(dev, B43_DBG_PWORK_STOP)) 3439 goto out_requeue; 3440 3441 do_periodic_work(dev); 3442 3443 dev->periodic_state++; 3444 out_requeue: 3445 if (b43_debug(dev, B43_DBG_PWORK_FAST)) 3446 delay = msecs_to_jiffies(50); 3447 else 3448 delay = round_jiffies_relative(HZ * 15); 3449 ieee80211_queue_delayed_work(wl->hw, &dev->periodic_work, delay); 3450 out: 3451 mutex_unlock(&wl->mutex); 3452 } 3453 3454 static void b43_periodic_tasks_setup(struct b43_wldev *dev) 3455 { 3456 struct delayed_work *work = &dev->periodic_work; 3457 3458 dev->periodic_state = 0; 3459 INIT_DELAYED_WORK(work, b43_periodic_work_handler); 3460 ieee80211_queue_delayed_work(dev->wl->hw, work, 0); 3461 } 3462 3463 /* Check if communication with the device works correctly. */ 3464 static int b43_validate_chipaccess(struct b43_wldev *dev) 3465 { 3466 u32 v, backup0, backup4; 3467 3468 backup0 = b43_shm_read32(dev, B43_SHM_SHARED, 0); 3469 backup4 = b43_shm_read32(dev, B43_SHM_SHARED, 4); 3470 3471 /* Check for read/write and endianness problems. */ 3472 b43_shm_write32(dev, B43_SHM_SHARED, 0, 0x55AAAA55); 3473 if (b43_shm_read32(dev, B43_SHM_SHARED, 0) != 0x55AAAA55) 3474 goto error; 3475 b43_shm_write32(dev, B43_SHM_SHARED, 0, 0xAA5555AA); 3476 if (b43_shm_read32(dev, B43_SHM_SHARED, 0) != 0xAA5555AA) 3477 goto error; 3478 3479 /* Check if unaligned 32bit SHM_SHARED access works properly. 3480 * However, don't bail out on failure, because it's noncritical. */ 3481 b43_shm_write16(dev, B43_SHM_SHARED, 0, 0x1122); 3482 b43_shm_write16(dev, B43_SHM_SHARED, 2, 0x3344); 3483 b43_shm_write16(dev, B43_SHM_SHARED, 4, 0x5566); 3484 b43_shm_write16(dev, B43_SHM_SHARED, 6, 0x7788); 3485 if (b43_shm_read32(dev, B43_SHM_SHARED, 2) != 0x55663344) 3486 b43warn(dev->wl, "Unaligned 32bit SHM read access is broken\n"); 3487 b43_shm_write32(dev, B43_SHM_SHARED, 2, 0xAABBCCDD); 3488 if (b43_shm_read16(dev, B43_SHM_SHARED, 0) != 0x1122 || 3489 b43_shm_read16(dev, B43_SHM_SHARED, 2) != 0xCCDD || 3490 b43_shm_read16(dev, B43_SHM_SHARED, 4) != 0xAABB || 3491 b43_shm_read16(dev, B43_SHM_SHARED, 6) != 0x7788) 3492 b43warn(dev->wl, "Unaligned 32bit SHM write access is broken\n"); 3493 3494 b43_shm_write32(dev, B43_SHM_SHARED, 0, backup0); 3495 b43_shm_write32(dev, B43_SHM_SHARED, 4, backup4); 3496 3497 if ((dev->dev->core_rev >= 3) && (dev->dev->core_rev <= 10)) { 3498 /* The 32bit register shadows the two 16bit registers 3499 * with update sideeffects. Validate this. */ 3500 b43_write16(dev, B43_MMIO_TSF_CFP_START, 0xAAAA); 3501 b43_write32(dev, B43_MMIO_TSF_CFP_START, 0xCCCCBBBB); 3502 if (b43_read16(dev, B43_MMIO_TSF_CFP_START_LOW) != 0xBBBB) 3503 goto error; 3504 if (b43_read16(dev, B43_MMIO_TSF_CFP_START_HIGH) != 0xCCCC) 3505 goto error; 3506 } 3507 b43_write32(dev, B43_MMIO_TSF_CFP_START, 0); 3508 3509 v = b43_read32(dev, B43_MMIO_MACCTL); 3510 v |= B43_MACCTL_GMODE; 3511 if (v != (B43_MACCTL_GMODE | B43_MACCTL_IHR_ENABLED)) 3512 goto error; 3513 3514 return 0; 3515 error: 3516 b43err(dev->wl, "Failed to validate the chipaccess\n"); 3517 return -ENODEV; 3518 } 3519 3520 static void b43_security_init(struct b43_wldev *dev) 3521 { 3522 dev->ktp = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_KTP); 3523 /* KTP is a word address, but we address SHM bytewise. 3524 * So multiply by two. 3525 */ 3526 dev->ktp *= 2; 3527 /* Number of RCMTA address slots */ 3528 b43_write16(dev, B43_MMIO_RCMTA_COUNT, B43_NR_PAIRWISE_KEYS); 3529 /* Clear the key memory. */ 3530 b43_clear_keys(dev); 3531 } 3532 3533 #ifdef CONFIG_B43_HWRNG 3534 static int b43_rng_read(struct hwrng *rng, u32 *data) 3535 { 3536 struct b43_wl *wl = (struct b43_wl *)rng->priv; 3537 struct b43_wldev *dev; 3538 int count = -ENODEV; 3539 3540 mutex_lock(&wl->mutex); 3541 dev = wl->current_dev; 3542 if (likely(dev && b43_status(dev) >= B43_STAT_INITIALIZED)) { 3543 *data = b43_read16(dev, B43_MMIO_RNG); 3544 count = sizeof(u16); 3545 } 3546 mutex_unlock(&wl->mutex); 3547 3548 return count; 3549 } 3550 #endif /* CONFIG_B43_HWRNG */ 3551 3552 static void b43_rng_exit(struct b43_wl *wl) 3553 { 3554 #ifdef CONFIG_B43_HWRNG 3555 if (wl->rng_initialized) 3556 hwrng_unregister(&wl->rng); 3557 #endif /* CONFIG_B43_HWRNG */ 3558 } 3559 3560 static int b43_rng_init(struct b43_wl *wl) 3561 { 3562 int err = 0; 3563 3564 #ifdef CONFIG_B43_HWRNG 3565 snprintf(wl->rng_name, ARRAY_SIZE(wl->rng_name), 3566 "%s_%s", KBUILD_MODNAME, wiphy_name(wl->hw->wiphy)); 3567 wl->rng.name = wl->rng_name; 3568 wl->rng.data_read = b43_rng_read; 3569 wl->rng.priv = (unsigned long)wl; 3570 wl->rng_initialized = true; 3571 err = hwrng_register(&wl->rng); 3572 if (err) { 3573 wl->rng_initialized = false; 3574 b43err(wl, "Failed to register the random " 3575 "number generator (%d)\n", err); 3576 } 3577 #endif /* CONFIG_B43_HWRNG */ 3578 3579 return err; 3580 } 3581 3582 static void b43_tx_work(struct work_struct *work) 3583 { 3584 struct b43_wl *wl = container_of(work, struct b43_wl, tx_work); 3585 struct b43_wldev *dev; 3586 struct sk_buff *skb; 3587 int queue_num; 3588 int err = 0; 3589 3590 mutex_lock(&wl->mutex); 3591 dev = wl->current_dev; 3592 if (unlikely(!dev || b43_status(dev) < B43_STAT_STARTED)) { 3593 mutex_unlock(&wl->mutex); 3594 return; 3595 } 3596 3597 for (queue_num = 0; queue_num < B43_QOS_QUEUE_NUM; queue_num++) { 3598 while (skb_queue_len(&wl->tx_queue[queue_num])) { 3599 skb = skb_dequeue(&wl->tx_queue[queue_num]); 3600 if (b43_using_pio_transfers(dev)) 3601 err = b43_pio_tx(dev, skb); 3602 else 3603 err = b43_dma_tx(dev, skb); 3604 if (err == -ENOSPC) { 3605 wl->tx_queue_stopped[queue_num] = true; 3606 ieee80211_stop_queue(wl->hw, queue_num); 3607 skb_queue_head(&wl->tx_queue[queue_num], skb); 3608 break; 3609 } 3610 if (unlikely(err)) 3611 ieee80211_free_txskb(wl->hw, skb); 3612 err = 0; 3613 } 3614 3615 if (!err) 3616 wl->tx_queue_stopped[queue_num] = false; 3617 } 3618 3619 #if B43_DEBUG 3620 dev->tx_count++; 3621 #endif 3622 mutex_unlock(&wl->mutex); 3623 } 3624 3625 static void b43_op_tx(struct ieee80211_hw *hw, 3626 struct ieee80211_tx_control *control, 3627 struct sk_buff *skb) 3628 { 3629 struct b43_wl *wl = hw_to_b43_wl(hw); 3630 3631 if (unlikely(skb->len < 2 + 2 + 6)) { 3632 /* Too short, this can't be a valid frame. */ 3633 ieee80211_free_txskb(hw, skb); 3634 return; 3635 } 3636 B43_WARN_ON(skb_shinfo(skb)->nr_frags); 3637 3638 skb_queue_tail(&wl->tx_queue[skb->queue_mapping], skb); 3639 if (!wl->tx_queue_stopped[skb->queue_mapping]) { 3640 ieee80211_queue_work(wl->hw, &wl->tx_work); 3641 } else { 3642 ieee80211_stop_queue(wl->hw, skb->queue_mapping); 3643 } 3644 } 3645 3646 static void b43_qos_params_upload(struct b43_wldev *dev, 3647 const struct ieee80211_tx_queue_params *p, 3648 u16 shm_offset) 3649 { 3650 u16 params[B43_NR_QOSPARAMS]; 3651 int bslots, tmp; 3652 unsigned int i; 3653 3654 if (!dev->qos_enabled) 3655 return; 3656 3657 bslots = b43_read16(dev, B43_MMIO_RNG) & p->cw_min; 3658 3659 memset(¶ms, 0, sizeof(params)); 3660 3661 params[B43_QOSPARAM_TXOP] = p->txop * 32; 3662 params[B43_QOSPARAM_CWMIN] = p->cw_min; 3663 params[B43_QOSPARAM_CWMAX] = p->cw_max; 3664 params[B43_QOSPARAM_CWCUR] = p->cw_min; 3665 params[B43_QOSPARAM_AIFS] = p->aifs; 3666 params[B43_QOSPARAM_BSLOTS] = bslots; 3667 params[B43_QOSPARAM_REGGAP] = bslots + p->aifs; 3668 3669 for (i = 0; i < ARRAY_SIZE(params); i++) { 3670 if (i == B43_QOSPARAM_STATUS) { 3671 tmp = b43_shm_read16(dev, B43_SHM_SHARED, 3672 shm_offset + (i * 2)); 3673 /* Mark the parameters as updated. */ 3674 tmp |= 0x100; 3675 b43_shm_write16(dev, B43_SHM_SHARED, 3676 shm_offset + (i * 2), 3677 tmp); 3678 } else { 3679 b43_shm_write16(dev, B43_SHM_SHARED, 3680 shm_offset + (i * 2), 3681 params[i]); 3682 } 3683 } 3684 } 3685 3686 /* Mapping of mac80211 queue numbers to b43 QoS SHM offsets. */ 3687 static const u16 b43_qos_shm_offsets[] = { 3688 /* [mac80211-queue-nr] = SHM_OFFSET, */ 3689 [0] = B43_QOS_VOICE, 3690 [1] = B43_QOS_VIDEO, 3691 [2] = B43_QOS_BESTEFFORT, 3692 [3] = B43_QOS_BACKGROUND, 3693 }; 3694 3695 /* Update all QOS parameters in hardware. */ 3696 static void b43_qos_upload_all(struct b43_wldev *dev) 3697 { 3698 struct b43_wl *wl = dev->wl; 3699 struct b43_qos_params *params; 3700 unsigned int i; 3701 3702 if (!dev->qos_enabled) 3703 return; 3704 3705 BUILD_BUG_ON(ARRAY_SIZE(b43_qos_shm_offsets) != 3706 ARRAY_SIZE(wl->qos_params)); 3707 3708 b43_mac_suspend(dev); 3709 for (i = 0; i < ARRAY_SIZE(wl->qos_params); i++) { 3710 params = &(wl->qos_params[i]); 3711 b43_qos_params_upload(dev, &(params->p), 3712 b43_qos_shm_offsets[i]); 3713 } 3714 b43_mac_enable(dev); 3715 } 3716 3717 static void b43_qos_clear(struct b43_wl *wl) 3718 { 3719 struct b43_qos_params *params; 3720 unsigned int i; 3721 3722 /* Initialize QoS parameters to sane defaults. */ 3723 3724 BUILD_BUG_ON(ARRAY_SIZE(b43_qos_shm_offsets) != 3725 ARRAY_SIZE(wl->qos_params)); 3726 3727 for (i = 0; i < ARRAY_SIZE(wl->qos_params); i++) { 3728 params = &(wl->qos_params[i]); 3729 3730 switch (b43_qos_shm_offsets[i]) { 3731 case B43_QOS_VOICE: 3732 params->p.txop = 0; 3733 params->p.aifs = 2; 3734 params->p.cw_min = 0x0001; 3735 params->p.cw_max = 0x0001; 3736 break; 3737 case B43_QOS_VIDEO: 3738 params->p.txop = 0; 3739 params->p.aifs = 2; 3740 params->p.cw_min = 0x0001; 3741 params->p.cw_max = 0x0001; 3742 break; 3743 case B43_QOS_BESTEFFORT: 3744 params->p.txop = 0; 3745 params->p.aifs = 3; 3746 params->p.cw_min = 0x0001; 3747 params->p.cw_max = 0x03FF; 3748 break; 3749 case B43_QOS_BACKGROUND: 3750 params->p.txop = 0; 3751 params->p.aifs = 7; 3752 params->p.cw_min = 0x0001; 3753 params->p.cw_max = 0x03FF; 3754 break; 3755 default: 3756 B43_WARN_ON(1); 3757 } 3758 } 3759 } 3760 3761 /* Initialize the core's QOS capabilities */ 3762 static void b43_qos_init(struct b43_wldev *dev) 3763 { 3764 if (!dev->qos_enabled) { 3765 /* Disable QOS support. */ 3766 b43_hf_write(dev, b43_hf_read(dev) & ~B43_HF_EDCF); 3767 b43_write16(dev, B43_MMIO_IFSCTL, 3768 b43_read16(dev, B43_MMIO_IFSCTL) 3769 & ~B43_MMIO_IFSCTL_USE_EDCF); 3770 b43dbg(dev->wl, "QoS disabled\n"); 3771 return; 3772 } 3773 3774 /* Upload the current QOS parameters. */ 3775 b43_qos_upload_all(dev); 3776 3777 /* Enable QOS support. */ 3778 b43_hf_write(dev, b43_hf_read(dev) | B43_HF_EDCF); 3779 b43_write16(dev, B43_MMIO_IFSCTL, 3780 b43_read16(dev, B43_MMIO_IFSCTL) 3781 | B43_MMIO_IFSCTL_USE_EDCF); 3782 b43dbg(dev->wl, "QoS enabled\n"); 3783 } 3784 3785 static int b43_op_conf_tx(struct ieee80211_hw *hw, 3786 struct ieee80211_vif *vif, u16 _queue, 3787 const struct ieee80211_tx_queue_params *params) 3788 { 3789 struct b43_wl *wl = hw_to_b43_wl(hw); 3790 struct b43_wldev *dev; 3791 unsigned int queue = (unsigned int)_queue; 3792 int err = -ENODEV; 3793 3794 if (queue >= ARRAY_SIZE(wl->qos_params)) { 3795 /* Queue not available or don't support setting 3796 * params on this queue. Return success to not 3797 * confuse mac80211. */ 3798 return 0; 3799 } 3800 BUILD_BUG_ON(ARRAY_SIZE(b43_qos_shm_offsets) != 3801 ARRAY_SIZE(wl->qos_params)); 3802 3803 mutex_lock(&wl->mutex); 3804 dev = wl->current_dev; 3805 if (unlikely(!dev || (b43_status(dev) < B43_STAT_INITIALIZED))) 3806 goto out_unlock; 3807 3808 memcpy(&(wl->qos_params[queue].p), params, sizeof(*params)); 3809 b43_mac_suspend(dev); 3810 b43_qos_params_upload(dev, &(wl->qos_params[queue].p), 3811 b43_qos_shm_offsets[queue]); 3812 b43_mac_enable(dev); 3813 err = 0; 3814 3815 out_unlock: 3816 mutex_unlock(&wl->mutex); 3817 3818 return err; 3819 } 3820 3821 static int b43_op_get_stats(struct ieee80211_hw *hw, 3822 struct ieee80211_low_level_stats *stats) 3823 { 3824 struct b43_wl *wl = hw_to_b43_wl(hw); 3825 3826 mutex_lock(&wl->mutex); 3827 memcpy(stats, &wl->ieee_stats, sizeof(*stats)); 3828 mutex_unlock(&wl->mutex); 3829 3830 return 0; 3831 } 3832 3833 static u64 b43_op_get_tsf(struct ieee80211_hw *hw, struct ieee80211_vif *vif) 3834 { 3835 struct b43_wl *wl = hw_to_b43_wl(hw); 3836 struct b43_wldev *dev; 3837 u64 tsf; 3838 3839 mutex_lock(&wl->mutex); 3840 dev = wl->current_dev; 3841 3842 if (dev && (b43_status(dev) >= B43_STAT_INITIALIZED)) 3843 b43_tsf_read(dev, &tsf); 3844 else 3845 tsf = 0; 3846 3847 mutex_unlock(&wl->mutex); 3848 3849 return tsf; 3850 } 3851 3852 static void b43_op_set_tsf(struct ieee80211_hw *hw, 3853 struct ieee80211_vif *vif, u64 tsf) 3854 { 3855 struct b43_wl *wl = hw_to_b43_wl(hw); 3856 struct b43_wldev *dev; 3857 3858 mutex_lock(&wl->mutex); 3859 dev = wl->current_dev; 3860 3861 if (dev && (b43_status(dev) >= B43_STAT_INITIALIZED)) 3862 b43_tsf_write(dev, tsf); 3863 3864 mutex_unlock(&wl->mutex); 3865 } 3866 3867 static const char *band_to_string(enum nl80211_band band) 3868 { 3869 switch (band) { 3870 case NL80211_BAND_5GHZ: 3871 return "5"; 3872 case NL80211_BAND_2GHZ: 3873 return "2.4"; 3874 default: 3875 break; 3876 } 3877 B43_WARN_ON(1); 3878 return ""; 3879 } 3880 3881 /* Expects wl->mutex locked */ 3882 static int b43_switch_band(struct b43_wldev *dev, 3883 struct ieee80211_channel *chan) 3884 { 3885 struct b43_phy *phy = &dev->phy; 3886 bool gmode; 3887 u32 tmp; 3888 3889 switch (chan->band) { 3890 case NL80211_BAND_5GHZ: 3891 gmode = false; 3892 break; 3893 case NL80211_BAND_2GHZ: 3894 gmode = true; 3895 break; 3896 default: 3897 B43_WARN_ON(1); 3898 return -EINVAL; 3899 } 3900 3901 if (!((gmode && phy->supports_2ghz) || 3902 (!gmode && phy->supports_5ghz))) { 3903 b43err(dev->wl, "This device doesn't support %s-GHz band\n", 3904 band_to_string(chan->band)); 3905 return -ENODEV; 3906 } 3907 3908 if (!!phy->gmode == !!gmode) { 3909 /* This device is already running. */ 3910 return 0; 3911 } 3912 3913 b43dbg(dev->wl, "Switching to %s GHz band\n", 3914 band_to_string(chan->band)); 3915 3916 /* Some new devices don't need disabling radio for band switching */ 3917 if (!(phy->type == B43_PHYTYPE_N && phy->rev >= 3)) 3918 b43_software_rfkill(dev, true); 3919 3920 phy->gmode = gmode; 3921 b43_phy_put_into_reset(dev); 3922 switch (dev->dev->bus_type) { 3923 #ifdef CONFIG_B43_BCMA 3924 case B43_BUS_BCMA: 3925 tmp = bcma_aread32(dev->dev->bdev, BCMA_IOCTL); 3926 if (gmode) 3927 tmp |= B43_BCMA_IOCTL_GMODE; 3928 else 3929 tmp &= ~B43_BCMA_IOCTL_GMODE; 3930 bcma_awrite32(dev->dev->bdev, BCMA_IOCTL, tmp); 3931 break; 3932 #endif 3933 #ifdef CONFIG_B43_SSB 3934 case B43_BUS_SSB: 3935 tmp = ssb_read32(dev->dev->sdev, SSB_TMSLOW); 3936 if (gmode) 3937 tmp |= B43_TMSLOW_GMODE; 3938 else 3939 tmp &= ~B43_TMSLOW_GMODE; 3940 ssb_write32(dev->dev->sdev, SSB_TMSLOW, tmp); 3941 break; 3942 #endif 3943 } 3944 b43_phy_take_out_of_reset(dev); 3945 3946 b43_upload_initvals_band(dev); 3947 3948 b43_phy_init(dev); 3949 3950 return 0; 3951 } 3952 3953 static void b43_set_beacon_listen_interval(struct b43_wldev *dev, u16 interval) 3954 { 3955 interval = min_t(u16, interval, (u16)0xFF); 3956 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_BCN_LI, interval); 3957 } 3958 3959 /* Write the short and long frame retry limit values. */ 3960 static void b43_set_retry_limits(struct b43_wldev *dev, 3961 unsigned int short_retry, 3962 unsigned int long_retry) 3963 { 3964 /* The retry limit is a 4-bit counter. Enforce this to avoid overflowing 3965 * the chip-internal counter. */ 3966 short_retry = min(short_retry, (unsigned int)0xF); 3967 long_retry = min(long_retry, (unsigned int)0xF); 3968 3969 b43_shm_write16(dev, B43_SHM_SCRATCH, B43_SHM_SC_SRLIMIT, 3970 short_retry); 3971 b43_shm_write16(dev, B43_SHM_SCRATCH, B43_SHM_SC_LRLIMIT, 3972 long_retry); 3973 } 3974 3975 static int b43_op_config(struct ieee80211_hw *hw, u32 changed) 3976 { 3977 struct b43_wl *wl = hw_to_b43_wl(hw); 3978 struct b43_wldev *dev = wl->current_dev; 3979 struct b43_phy *phy = &dev->phy; 3980 struct ieee80211_conf *conf = &hw->conf; 3981 int antenna; 3982 int err = 0; 3983 3984 mutex_lock(&wl->mutex); 3985 b43_mac_suspend(dev); 3986 3987 if (changed & IEEE80211_CONF_CHANGE_LISTEN_INTERVAL) 3988 b43_set_beacon_listen_interval(dev, conf->listen_interval); 3989 3990 if (changed & IEEE80211_CONF_CHANGE_CHANNEL) { 3991 phy->chandef = &conf->chandef; 3992 phy->channel = conf->chandef.chan->hw_value; 3993 3994 /* Switch the band (if necessary). */ 3995 err = b43_switch_band(dev, conf->chandef.chan); 3996 if (err) 3997 goto out_mac_enable; 3998 3999 /* Switch to the requested channel. 4000 * The firmware takes care of races with the TX handler. 4001 */ 4002 b43_switch_channel(dev, phy->channel); 4003 } 4004 4005 if (changed & IEEE80211_CONF_CHANGE_RETRY_LIMITS) 4006 b43_set_retry_limits(dev, conf->short_frame_max_tx_count, 4007 conf->long_frame_max_tx_count); 4008 changed &= ~IEEE80211_CONF_CHANGE_RETRY_LIMITS; 4009 if (!changed) 4010 goto out_mac_enable; 4011 4012 dev->wl->radiotap_enabled = !!(conf->flags & IEEE80211_CONF_MONITOR); 4013 4014 /* Adjust the desired TX power level. */ 4015 if (conf->power_level != 0) { 4016 if (conf->power_level != phy->desired_txpower) { 4017 phy->desired_txpower = conf->power_level; 4018 b43_phy_txpower_check(dev, B43_TXPWR_IGNORE_TIME | 4019 B43_TXPWR_IGNORE_TSSI); 4020 } 4021 } 4022 4023 /* Antennas for RX and management frame TX. */ 4024 antenna = B43_ANTENNA_DEFAULT; 4025 b43_mgmtframe_txantenna(dev, antenna); 4026 antenna = B43_ANTENNA_DEFAULT; 4027 if (phy->ops->set_rx_antenna) 4028 phy->ops->set_rx_antenna(dev, antenna); 4029 4030 if (wl->radio_enabled != phy->radio_on) { 4031 if (wl->radio_enabled) { 4032 b43_software_rfkill(dev, false); 4033 b43info(dev->wl, "Radio turned on by software\n"); 4034 if (!dev->radio_hw_enable) { 4035 b43info(dev->wl, "The hardware RF-kill button " 4036 "still turns the radio physically off. " 4037 "Press the button to turn it on.\n"); 4038 } 4039 } else { 4040 b43_software_rfkill(dev, true); 4041 b43info(dev->wl, "Radio turned off by software\n"); 4042 } 4043 } 4044 4045 out_mac_enable: 4046 b43_mac_enable(dev); 4047 mutex_unlock(&wl->mutex); 4048 4049 return err; 4050 } 4051 4052 static void b43_update_basic_rates(struct b43_wldev *dev, u32 brates) 4053 { 4054 struct ieee80211_supported_band *sband = 4055 dev->wl->hw->wiphy->bands[b43_current_band(dev->wl)]; 4056 const struct ieee80211_rate *rate; 4057 int i; 4058 u16 basic, direct, offset, basic_offset, rateptr; 4059 4060 for (i = 0; i < sband->n_bitrates; i++) { 4061 rate = &sband->bitrates[i]; 4062 4063 if (b43_is_cck_rate(rate->hw_value)) { 4064 direct = B43_SHM_SH_CCKDIRECT; 4065 basic = B43_SHM_SH_CCKBASIC; 4066 offset = b43_plcp_get_ratecode_cck(rate->hw_value); 4067 offset &= 0xF; 4068 } else { 4069 direct = B43_SHM_SH_OFDMDIRECT; 4070 basic = B43_SHM_SH_OFDMBASIC; 4071 offset = b43_plcp_get_ratecode_ofdm(rate->hw_value); 4072 offset &= 0xF; 4073 } 4074 4075 rate = ieee80211_get_response_rate(sband, brates, rate->bitrate); 4076 4077 if (b43_is_cck_rate(rate->hw_value)) { 4078 basic_offset = b43_plcp_get_ratecode_cck(rate->hw_value); 4079 basic_offset &= 0xF; 4080 } else { 4081 basic_offset = b43_plcp_get_ratecode_ofdm(rate->hw_value); 4082 basic_offset &= 0xF; 4083 } 4084 4085 /* 4086 * Get the pointer that we need to point to 4087 * from the direct map 4088 */ 4089 rateptr = b43_shm_read16(dev, B43_SHM_SHARED, 4090 direct + 2 * basic_offset); 4091 /* and write it to the basic map */ 4092 b43_shm_write16(dev, B43_SHM_SHARED, basic + 2 * offset, 4093 rateptr); 4094 } 4095 } 4096 4097 static void b43_op_bss_info_changed(struct ieee80211_hw *hw, 4098 struct ieee80211_vif *vif, 4099 struct ieee80211_bss_conf *conf, 4100 u32 changed) 4101 { 4102 struct b43_wl *wl = hw_to_b43_wl(hw); 4103 struct b43_wldev *dev; 4104 4105 mutex_lock(&wl->mutex); 4106 4107 dev = wl->current_dev; 4108 if (!dev || b43_status(dev) < B43_STAT_STARTED) 4109 goto out_unlock_mutex; 4110 4111 B43_WARN_ON(wl->vif != vif); 4112 4113 if (changed & BSS_CHANGED_BSSID) { 4114 if (conf->bssid) 4115 memcpy(wl->bssid, conf->bssid, ETH_ALEN); 4116 else 4117 eth_zero_addr(wl->bssid); 4118 } 4119 4120 if (b43_status(dev) >= B43_STAT_INITIALIZED) { 4121 if (changed & BSS_CHANGED_BEACON && 4122 (b43_is_mode(wl, NL80211_IFTYPE_AP) || 4123 b43_is_mode(wl, NL80211_IFTYPE_MESH_POINT) || 4124 b43_is_mode(wl, NL80211_IFTYPE_ADHOC))) 4125 b43_update_templates(wl); 4126 4127 if (changed & BSS_CHANGED_BSSID) 4128 b43_write_mac_bssid_templates(dev); 4129 } 4130 4131 b43_mac_suspend(dev); 4132 4133 /* Update templates for AP/mesh mode. */ 4134 if (changed & BSS_CHANGED_BEACON_INT && 4135 (b43_is_mode(wl, NL80211_IFTYPE_AP) || 4136 b43_is_mode(wl, NL80211_IFTYPE_MESH_POINT) || 4137 b43_is_mode(wl, NL80211_IFTYPE_ADHOC)) && 4138 conf->beacon_int) 4139 b43_set_beacon_int(dev, conf->beacon_int); 4140 4141 if (changed & BSS_CHANGED_BASIC_RATES) 4142 b43_update_basic_rates(dev, conf->basic_rates); 4143 4144 if (changed & BSS_CHANGED_ERP_SLOT) { 4145 if (conf->use_short_slot) 4146 b43_short_slot_timing_enable(dev); 4147 else 4148 b43_short_slot_timing_disable(dev); 4149 } 4150 4151 b43_mac_enable(dev); 4152 out_unlock_mutex: 4153 mutex_unlock(&wl->mutex); 4154 } 4155 4156 static int b43_op_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd, 4157 struct ieee80211_vif *vif, struct ieee80211_sta *sta, 4158 struct ieee80211_key_conf *key) 4159 { 4160 struct b43_wl *wl = hw_to_b43_wl(hw); 4161 struct b43_wldev *dev; 4162 u8 algorithm; 4163 u8 index; 4164 int err; 4165 static const u8 bcast_addr[ETH_ALEN] = { 0xff, 0xff, 0xff, 0xff, 0xff, 0xff }; 4166 4167 if (modparam_nohwcrypt) 4168 return -ENOSPC; /* User disabled HW-crypto */ 4169 4170 if ((vif->type == NL80211_IFTYPE_ADHOC || 4171 vif->type == NL80211_IFTYPE_MESH_POINT) && 4172 (key->cipher == WLAN_CIPHER_SUITE_TKIP || 4173 key->cipher == WLAN_CIPHER_SUITE_CCMP) && 4174 !(key->flags & IEEE80211_KEY_FLAG_PAIRWISE)) { 4175 /* 4176 * For now, disable hw crypto for the RSN IBSS group keys. This 4177 * could be optimized in the future, but until that gets 4178 * implemented, use of software crypto for group addressed 4179 * frames is a acceptable to allow RSN IBSS to be used. 4180 */ 4181 return -EOPNOTSUPP; 4182 } 4183 4184 mutex_lock(&wl->mutex); 4185 4186 dev = wl->current_dev; 4187 err = -ENODEV; 4188 if (!dev || b43_status(dev) < B43_STAT_INITIALIZED) 4189 goto out_unlock; 4190 4191 if (dev->fw.pcm_request_failed || !dev->hwcrypto_enabled) { 4192 /* We don't have firmware for the crypto engine. 4193 * Must use software-crypto. */ 4194 err = -EOPNOTSUPP; 4195 goto out_unlock; 4196 } 4197 4198 err = -EINVAL; 4199 switch (key->cipher) { 4200 case WLAN_CIPHER_SUITE_WEP40: 4201 algorithm = B43_SEC_ALGO_WEP40; 4202 break; 4203 case WLAN_CIPHER_SUITE_WEP104: 4204 algorithm = B43_SEC_ALGO_WEP104; 4205 break; 4206 case WLAN_CIPHER_SUITE_TKIP: 4207 algorithm = B43_SEC_ALGO_TKIP; 4208 break; 4209 case WLAN_CIPHER_SUITE_CCMP: 4210 algorithm = B43_SEC_ALGO_AES; 4211 break; 4212 default: 4213 B43_WARN_ON(1); 4214 goto out_unlock; 4215 } 4216 index = (u8) (key->keyidx); 4217 if (index > 3) 4218 goto out_unlock; 4219 4220 switch (cmd) { 4221 case SET_KEY: 4222 if (algorithm == B43_SEC_ALGO_TKIP && 4223 (!(key->flags & IEEE80211_KEY_FLAG_PAIRWISE) || 4224 !modparam_hwtkip)) { 4225 /* We support only pairwise key */ 4226 err = -EOPNOTSUPP; 4227 goto out_unlock; 4228 } 4229 4230 if (key->flags & IEEE80211_KEY_FLAG_PAIRWISE) { 4231 if (WARN_ON(!sta)) { 4232 err = -EOPNOTSUPP; 4233 goto out_unlock; 4234 } 4235 /* Pairwise key with an assigned MAC address. */ 4236 err = b43_key_write(dev, -1, algorithm, 4237 key->key, key->keylen, 4238 sta->addr, key); 4239 } else { 4240 /* Group key */ 4241 err = b43_key_write(dev, index, algorithm, 4242 key->key, key->keylen, NULL, key); 4243 } 4244 if (err) 4245 goto out_unlock; 4246 4247 if (algorithm == B43_SEC_ALGO_WEP40 || 4248 algorithm == B43_SEC_ALGO_WEP104) { 4249 b43_hf_write(dev, b43_hf_read(dev) | B43_HF_USEDEFKEYS); 4250 } else { 4251 b43_hf_write(dev, 4252 b43_hf_read(dev) & ~B43_HF_USEDEFKEYS); 4253 } 4254 key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV; 4255 if (algorithm == B43_SEC_ALGO_TKIP) 4256 key->flags |= IEEE80211_KEY_FLAG_GENERATE_MMIC; 4257 break; 4258 case DISABLE_KEY: { 4259 err = b43_key_clear(dev, key->hw_key_idx); 4260 if (err) 4261 goto out_unlock; 4262 break; 4263 } 4264 default: 4265 B43_WARN_ON(1); 4266 } 4267 4268 out_unlock: 4269 if (!err) { 4270 b43dbg(wl, "%s hardware based encryption for keyidx: %d, " 4271 "mac: %pM\n", 4272 cmd == SET_KEY ? "Using" : "Disabling", key->keyidx, 4273 sta ? sta->addr : bcast_addr); 4274 b43_dump_keymemory(dev); 4275 } 4276 mutex_unlock(&wl->mutex); 4277 4278 return err; 4279 } 4280 4281 static void b43_op_configure_filter(struct ieee80211_hw *hw, 4282 unsigned int changed, unsigned int *fflags, 4283 u64 multicast) 4284 { 4285 struct b43_wl *wl = hw_to_b43_wl(hw); 4286 struct b43_wldev *dev; 4287 4288 mutex_lock(&wl->mutex); 4289 dev = wl->current_dev; 4290 if (!dev) { 4291 *fflags = 0; 4292 goto out_unlock; 4293 } 4294 4295 *fflags &= FIF_ALLMULTI | 4296 FIF_FCSFAIL | 4297 FIF_PLCPFAIL | 4298 FIF_CONTROL | 4299 FIF_OTHER_BSS | 4300 FIF_BCN_PRBRESP_PROMISC; 4301 4302 changed &= FIF_ALLMULTI | 4303 FIF_FCSFAIL | 4304 FIF_PLCPFAIL | 4305 FIF_CONTROL | 4306 FIF_OTHER_BSS | 4307 FIF_BCN_PRBRESP_PROMISC; 4308 4309 wl->filter_flags = *fflags; 4310 4311 if (changed && b43_status(dev) >= B43_STAT_INITIALIZED) 4312 b43_adjust_opmode(dev); 4313 4314 out_unlock: 4315 mutex_unlock(&wl->mutex); 4316 } 4317 4318 /* Locking: wl->mutex 4319 * Returns the current dev. This might be different from the passed in dev, 4320 * because the core might be gone away while we unlocked the mutex. */ 4321 static struct b43_wldev * b43_wireless_core_stop(struct b43_wldev *dev) 4322 { 4323 struct b43_wl *wl; 4324 struct b43_wldev *orig_dev; 4325 u32 mask; 4326 int queue_num; 4327 4328 if (!dev) 4329 return NULL; 4330 wl = dev->wl; 4331 redo: 4332 if (!dev || b43_status(dev) < B43_STAT_STARTED) 4333 return dev; 4334 4335 /* Cancel work. Unlock to avoid deadlocks. */ 4336 mutex_unlock(&wl->mutex); 4337 cancel_delayed_work_sync(&dev->periodic_work); 4338 cancel_work_sync(&wl->tx_work); 4339 b43_leds_stop(dev); 4340 mutex_lock(&wl->mutex); 4341 dev = wl->current_dev; 4342 if (!dev || b43_status(dev) < B43_STAT_STARTED) { 4343 /* Whoops, aliens ate up the device while we were unlocked. */ 4344 return dev; 4345 } 4346 4347 /* Disable interrupts on the device. */ 4348 b43_set_status(dev, B43_STAT_INITIALIZED); 4349 if (b43_bus_host_is_sdio(dev->dev)) { 4350 /* wl->mutex is locked. That is enough. */ 4351 b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, 0); 4352 b43_read32(dev, B43_MMIO_GEN_IRQ_MASK); /* Flush */ 4353 } else { 4354 spin_lock_irq(&wl->hardirq_lock); 4355 b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, 0); 4356 b43_read32(dev, B43_MMIO_GEN_IRQ_MASK); /* Flush */ 4357 spin_unlock_irq(&wl->hardirq_lock); 4358 } 4359 /* Synchronize and free the interrupt handlers. Unlock to avoid deadlocks. */ 4360 orig_dev = dev; 4361 mutex_unlock(&wl->mutex); 4362 if (b43_bus_host_is_sdio(dev->dev)) 4363 b43_sdio_free_irq(dev); 4364 else 4365 free_irq(dev->dev->irq, dev); 4366 mutex_lock(&wl->mutex); 4367 dev = wl->current_dev; 4368 if (!dev) 4369 return dev; 4370 if (dev != orig_dev) { 4371 if (b43_status(dev) >= B43_STAT_STARTED) 4372 goto redo; 4373 return dev; 4374 } 4375 mask = b43_read32(dev, B43_MMIO_GEN_IRQ_MASK); 4376 B43_WARN_ON(mask != 0xFFFFFFFF && mask); 4377 4378 /* Drain all TX queues. */ 4379 for (queue_num = 0; queue_num < B43_QOS_QUEUE_NUM; queue_num++) { 4380 while (skb_queue_len(&wl->tx_queue[queue_num])) { 4381 struct sk_buff *skb; 4382 4383 skb = skb_dequeue(&wl->tx_queue[queue_num]); 4384 ieee80211_free_txskb(wl->hw, skb); 4385 } 4386 } 4387 4388 b43_mac_suspend(dev); 4389 b43_leds_exit(dev); 4390 b43dbg(wl, "Wireless interface stopped\n"); 4391 4392 return dev; 4393 } 4394 4395 /* Locking: wl->mutex */ 4396 static int b43_wireless_core_start(struct b43_wldev *dev) 4397 { 4398 int err; 4399 4400 B43_WARN_ON(b43_status(dev) != B43_STAT_INITIALIZED); 4401 4402 drain_txstatus_queue(dev); 4403 if (b43_bus_host_is_sdio(dev->dev)) { 4404 err = b43_sdio_request_irq(dev, b43_sdio_interrupt_handler); 4405 if (err) { 4406 b43err(dev->wl, "Cannot request SDIO IRQ\n"); 4407 goto out; 4408 } 4409 } else { 4410 err = request_threaded_irq(dev->dev->irq, b43_interrupt_handler, 4411 b43_interrupt_thread_handler, 4412 IRQF_SHARED, KBUILD_MODNAME, dev); 4413 if (err) { 4414 b43err(dev->wl, "Cannot request IRQ-%d\n", 4415 dev->dev->irq); 4416 goto out; 4417 } 4418 } 4419 4420 /* We are ready to run. */ 4421 ieee80211_wake_queues(dev->wl->hw); 4422 b43_set_status(dev, B43_STAT_STARTED); 4423 4424 /* Start data flow (TX/RX). */ 4425 b43_mac_enable(dev); 4426 b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, dev->irq_mask); 4427 4428 /* Start maintenance work */ 4429 b43_periodic_tasks_setup(dev); 4430 4431 b43_leds_init(dev); 4432 4433 b43dbg(dev->wl, "Wireless interface started\n"); 4434 out: 4435 return err; 4436 } 4437 4438 static char *b43_phy_name(struct b43_wldev *dev, u8 phy_type) 4439 { 4440 switch (phy_type) { 4441 case B43_PHYTYPE_A: 4442 return "A"; 4443 case B43_PHYTYPE_B: 4444 return "B"; 4445 case B43_PHYTYPE_G: 4446 return "G"; 4447 case B43_PHYTYPE_N: 4448 return "N"; 4449 case B43_PHYTYPE_LP: 4450 return "LP"; 4451 case B43_PHYTYPE_SSLPN: 4452 return "SSLPN"; 4453 case B43_PHYTYPE_HT: 4454 return "HT"; 4455 case B43_PHYTYPE_LCN: 4456 return "LCN"; 4457 case B43_PHYTYPE_LCNXN: 4458 return "LCNXN"; 4459 case B43_PHYTYPE_LCN40: 4460 return "LCN40"; 4461 case B43_PHYTYPE_AC: 4462 return "AC"; 4463 } 4464 return "UNKNOWN"; 4465 } 4466 4467 /* Get PHY and RADIO versioning numbers */ 4468 static int b43_phy_versioning(struct b43_wldev *dev) 4469 { 4470 struct b43_phy *phy = &dev->phy; 4471 const u8 core_rev = dev->dev->core_rev; 4472 u32 tmp; 4473 u8 analog_type; 4474 u8 phy_type; 4475 u8 phy_rev; 4476 u16 radio_manuf; 4477 u16 radio_id; 4478 u16 radio_rev; 4479 u8 radio_ver; 4480 int unsupported = 0; 4481 4482 /* Get PHY versioning */ 4483 tmp = b43_read16(dev, B43_MMIO_PHY_VER); 4484 analog_type = (tmp & B43_PHYVER_ANALOG) >> B43_PHYVER_ANALOG_SHIFT; 4485 phy_type = (tmp & B43_PHYVER_TYPE) >> B43_PHYVER_TYPE_SHIFT; 4486 phy_rev = (tmp & B43_PHYVER_VERSION); 4487 4488 /* LCNXN is continuation of N which run out of revisions */ 4489 if (phy_type == B43_PHYTYPE_LCNXN) { 4490 phy_type = B43_PHYTYPE_N; 4491 phy_rev += 16; 4492 } 4493 4494 switch (phy_type) { 4495 #ifdef CONFIG_B43_PHY_G 4496 case B43_PHYTYPE_G: 4497 if (phy_rev > 9) 4498 unsupported = 1; 4499 break; 4500 #endif 4501 #ifdef CONFIG_B43_PHY_N 4502 case B43_PHYTYPE_N: 4503 if (phy_rev >= 19) 4504 unsupported = 1; 4505 break; 4506 #endif 4507 #ifdef CONFIG_B43_PHY_LP 4508 case B43_PHYTYPE_LP: 4509 if (phy_rev > 2) 4510 unsupported = 1; 4511 break; 4512 #endif 4513 #ifdef CONFIG_B43_PHY_HT 4514 case B43_PHYTYPE_HT: 4515 if (phy_rev > 1) 4516 unsupported = 1; 4517 break; 4518 #endif 4519 #ifdef CONFIG_B43_PHY_LCN 4520 case B43_PHYTYPE_LCN: 4521 if (phy_rev > 1) 4522 unsupported = 1; 4523 break; 4524 #endif 4525 #ifdef CONFIG_B43_PHY_AC 4526 case B43_PHYTYPE_AC: 4527 if (phy_rev > 1) 4528 unsupported = 1; 4529 break; 4530 #endif 4531 default: 4532 unsupported = 1; 4533 } 4534 if (unsupported) { 4535 b43err(dev->wl, "FOUND UNSUPPORTED PHY (Analog %u, Type %d (%s), Revision %u)\n", 4536 analog_type, phy_type, b43_phy_name(dev, phy_type), 4537 phy_rev); 4538 return -EOPNOTSUPP; 4539 } 4540 b43info(dev->wl, "Found PHY: Analog %u, Type %d (%s), Revision %u\n", 4541 analog_type, phy_type, b43_phy_name(dev, phy_type), phy_rev); 4542 4543 /* Get RADIO versioning */ 4544 if (core_rev == 40 || core_rev == 42) { 4545 radio_manuf = 0x17F; 4546 4547 b43_write16f(dev, B43_MMIO_RADIO24_CONTROL, 0); 4548 radio_rev = b43_read16(dev, B43_MMIO_RADIO24_DATA); 4549 4550 b43_write16f(dev, B43_MMIO_RADIO24_CONTROL, 1); 4551 radio_id = b43_read16(dev, B43_MMIO_RADIO24_DATA); 4552 4553 radio_ver = 0; /* Is there version somewhere? */ 4554 } else if (core_rev >= 24) { 4555 u16 radio24[3]; 4556 4557 for (tmp = 0; tmp < 3; tmp++) { 4558 b43_write16f(dev, B43_MMIO_RADIO24_CONTROL, tmp); 4559 radio24[tmp] = b43_read16(dev, B43_MMIO_RADIO24_DATA); 4560 } 4561 4562 radio_manuf = 0x17F; 4563 radio_id = (radio24[2] << 8) | radio24[1]; 4564 radio_rev = (radio24[0] & 0xF); 4565 radio_ver = (radio24[0] & 0xF0) >> 4; 4566 } else { 4567 if (dev->dev->chip_id == 0x4317) { 4568 if (dev->dev->chip_rev == 0) 4569 tmp = 0x3205017F; 4570 else if (dev->dev->chip_rev == 1) 4571 tmp = 0x4205017F; 4572 else 4573 tmp = 0x5205017F; 4574 } else { 4575 b43_write16f(dev, B43_MMIO_RADIO_CONTROL, 4576 B43_RADIOCTL_ID); 4577 tmp = b43_read16(dev, B43_MMIO_RADIO_DATA_LOW); 4578 b43_write16f(dev, B43_MMIO_RADIO_CONTROL, 4579 B43_RADIOCTL_ID); 4580 tmp |= b43_read16(dev, B43_MMIO_RADIO_DATA_HIGH) << 16; 4581 } 4582 radio_manuf = (tmp & 0x00000FFF); 4583 radio_id = (tmp & 0x0FFFF000) >> 12; 4584 radio_rev = (tmp & 0xF0000000) >> 28; 4585 radio_ver = 0; /* Probably not available on old hw */ 4586 } 4587 4588 if (radio_manuf != 0x17F /* Broadcom */) 4589 unsupported = 1; 4590 switch (phy_type) { 4591 case B43_PHYTYPE_B: 4592 if ((radio_id & 0xFFF0) != 0x2050) 4593 unsupported = 1; 4594 break; 4595 case B43_PHYTYPE_G: 4596 if (radio_id != 0x2050) 4597 unsupported = 1; 4598 break; 4599 case B43_PHYTYPE_N: 4600 if (radio_id != 0x2055 && radio_id != 0x2056 && 4601 radio_id != 0x2057) 4602 unsupported = 1; 4603 if (radio_id == 0x2057 && 4604 !(radio_rev == 9 || radio_rev == 14)) 4605 unsupported = 1; 4606 break; 4607 case B43_PHYTYPE_LP: 4608 if (radio_id != 0x2062 && radio_id != 0x2063) 4609 unsupported = 1; 4610 break; 4611 case B43_PHYTYPE_HT: 4612 if (radio_id != 0x2059) 4613 unsupported = 1; 4614 break; 4615 case B43_PHYTYPE_LCN: 4616 if (radio_id != 0x2064) 4617 unsupported = 1; 4618 break; 4619 case B43_PHYTYPE_AC: 4620 if (radio_id != 0x2069) 4621 unsupported = 1; 4622 break; 4623 default: 4624 B43_WARN_ON(1); 4625 } 4626 if (unsupported) { 4627 b43err(dev->wl, 4628 "FOUND UNSUPPORTED RADIO (Manuf 0x%X, ID 0x%X, Revision %u, Version %u)\n", 4629 radio_manuf, radio_id, radio_rev, radio_ver); 4630 return -EOPNOTSUPP; 4631 } 4632 b43info(dev->wl, 4633 "Found Radio: Manuf 0x%X, ID 0x%X, Revision %u, Version %u\n", 4634 radio_manuf, radio_id, radio_rev, radio_ver); 4635 4636 /* FIXME: b43 treats "id" as "ver" and ignores the real "ver" */ 4637 phy->radio_manuf = radio_manuf; 4638 phy->radio_ver = radio_id; 4639 phy->radio_rev = radio_rev; 4640 4641 phy->analog = analog_type; 4642 phy->type = phy_type; 4643 phy->rev = phy_rev; 4644 4645 return 0; 4646 } 4647 4648 static void setup_struct_phy_for_init(struct b43_wldev *dev, 4649 struct b43_phy *phy) 4650 { 4651 phy->hardware_power_control = !!modparam_hwpctl; 4652 phy->next_txpwr_check_time = jiffies; 4653 /* PHY TX errors counter. */ 4654 atomic_set(&phy->txerr_cnt, B43_PHY_TX_BADNESS_LIMIT); 4655 4656 #if B43_DEBUG 4657 phy->phy_locked = false; 4658 phy->radio_locked = false; 4659 #endif 4660 } 4661 4662 static void setup_struct_wldev_for_init(struct b43_wldev *dev) 4663 { 4664 dev->dfq_valid = false; 4665 4666 /* Assume the radio is enabled. If it's not enabled, the state will 4667 * immediately get fixed on the first periodic work run. */ 4668 dev->radio_hw_enable = true; 4669 4670 /* Stats */ 4671 memset(&dev->stats, 0, sizeof(dev->stats)); 4672 4673 setup_struct_phy_for_init(dev, &dev->phy); 4674 4675 /* IRQ related flags */ 4676 dev->irq_reason = 0; 4677 memset(dev->dma_reason, 0, sizeof(dev->dma_reason)); 4678 dev->irq_mask = B43_IRQ_MASKTEMPLATE; 4679 if (b43_modparam_verbose < B43_VERBOSITY_DEBUG) 4680 dev->irq_mask &= ~B43_IRQ_PHY_TXERR; 4681 4682 dev->mac_suspended = 1; 4683 4684 /* Noise calculation context */ 4685 memset(&dev->noisecalc, 0, sizeof(dev->noisecalc)); 4686 } 4687 4688 static void b43_bluetooth_coext_enable(struct b43_wldev *dev) 4689 { 4690 struct ssb_sprom *sprom = dev->dev->bus_sprom; 4691 u64 hf; 4692 4693 if (!modparam_btcoex) 4694 return; 4695 if (!(sprom->boardflags_lo & B43_BFL_BTCOEXIST)) 4696 return; 4697 if (dev->phy.type != B43_PHYTYPE_B && !dev->phy.gmode) 4698 return; 4699 4700 hf = b43_hf_read(dev); 4701 if (sprom->boardflags_lo & B43_BFL_BTCMOD) 4702 hf |= B43_HF_BTCOEXALT; 4703 else 4704 hf |= B43_HF_BTCOEX; 4705 b43_hf_write(dev, hf); 4706 } 4707 4708 static void b43_bluetooth_coext_disable(struct b43_wldev *dev) 4709 { 4710 if (!modparam_btcoex) 4711 return; 4712 //TODO 4713 } 4714 4715 static void b43_imcfglo_timeouts_workaround(struct b43_wldev *dev) 4716 { 4717 struct ssb_bus *bus; 4718 u32 tmp; 4719 4720 #ifdef CONFIG_B43_SSB 4721 if (dev->dev->bus_type != B43_BUS_SSB) 4722 return; 4723 #else 4724 return; 4725 #endif 4726 4727 bus = dev->dev->sdev->bus; 4728 4729 if ((bus->chip_id == 0x4311 && bus->chip_rev == 2) || 4730 (bus->chip_id == 0x4312)) { 4731 tmp = ssb_read32(dev->dev->sdev, SSB_IMCFGLO); 4732 tmp &= ~SSB_IMCFGLO_REQTO; 4733 tmp &= ~SSB_IMCFGLO_SERTO; 4734 tmp |= 0x3; 4735 ssb_write32(dev->dev->sdev, SSB_IMCFGLO, tmp); 4736 ssb_commit_settings(bus); 4737 } 4738 } 4739 4740 static void b43_set_synth_pu_delay(struct b43_wldev *dev, bool idle) 4741 { 4742 u16 pu_delay; 4743 4744 /* The time value is in microseconds. */ 4745 pu_delay = 1050; 4746 if (b43_is_mode(dev->wl, NL80211_IFTYPE_ADHOC) || idle) 4747 pu_delay = 500; 4748 if ((dev->phy.radio_ver == 0x2050) && (dev->phy.radio_rev == 8)) 4749 pu_delay = max(pu_delay, (u16)2400); 4750 4751 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_SPUWKUP, pu_delay); 4752 } 4753 4754 /* Set the TSF CFP pre-TargetBeaconTransmissionTime. */ 4755 static void b43_set_pretbtt(struct b43_wldev *dev) 4756 { 4757 u16 pretbtt; 4758 4759 /* The time value is in microseconds. */ 4760 if (b43_is_mode(dev->wl, NL80211_IFTYPE_ADHOC)) 4761 pretbtt = 2; 4762 else 4763 pretbtt = 250; 4764 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_PRETBTT, pretbtt); 4765 b43_write16(dev, B43_MMIO_TSF_CFP_PRETBTT, pretbtt); 4766 } 4767 4768 /* Shutdown a wireless core */ 4769 /* Locking: wl->mutex */ 4770 static void b43_wireless_core_exit(struct b43_wldev *dev) 4771 { 4772 B43_WARN_ON(dev && b43_status(dev) > B43_STAT_INITIALIZED); 4773 if (!dev || b43_status(dev) != B43_STAT_INITIALIZED) 4774 return; 4775 4776 b43_set_status(dev, B43_STAT_UNINIT); 4777 4778 /* Stop the microcode PSM. */ 4779 b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_PSM_RUN, 4780 B43_MACCTL_PSM_JMP0); 4781 4782 switch (dev->dev->bus_type) { 4783 #ifdef CONFIG_B43_BCMA 4784 case B43_BUS_BCMA: 4785 bcma_host_pci_down(dev->dev->bdev->bus); 4786 break; 4787 #endif 4788 #ifdef CONFIG_B43_SSB 4789 case B43_BUS_SSB: 4790 /* TODO */ 4791 break; 4792 #endif 4793 } 4794 4795 b43_dma_free(dev); 4796 b43_pio_free(dev); 4797 b43_chip_exit(dev); 4798 dev->phy.ops->switch_analog(dev, 0); 4799 if (dev->wl->current_beacon) { 4800 dev_kfree_skb_any(dev->wl->current_beacon); 4801 dev->wl->current_beacon = NULL; 4802 } 4803 4804 b43_device_disable(dev, 0); 4805 b43_bus_may_powerdown(dev); 4806 } 4807 4808 /* Initialize a wireless core */ 4809 static int b43_wireless_core_init(struct b43_wldev *dev) 4810 { 4811 struct ssb_sprom *sprom = dev->dev->bus_sprom; 4812 struct b43_phy *phy = &dev->phy; 4813 int err; 4814 u64 hf; 4815 4816 B43_WARN_ON(b43_status(dev) != B43_STAT_UNINIT); 4817 4818 err = b43_bus_powerup(dev, 0); 4819 if (err) 4820 goto out; 4821 if (!b43_device_is_enabled(dev)) 4822 b43_wireless_core_reset(dev, phy->gmode); 4823 4824 /* Reset all data structures. */ 4825 setup_struct_wldev_for_init(dev); 4826 phy->ops->prepare_structs(dev); 4827 4828 /* Enable IRQ routing to this device. */ 4829 switch (dev->dev->bus_type) { 4830 #ifdef CONFIG_B43_BCMA 4831 case B43_BUS_BCMA: 4832 bcma_host_pci_irq_ctl(dev->dev->bdev->bus, 4833 dev->dev->bdev, true); 4834 bcma_host_pci_up(dev->dev->bdev->bus); 4835 break; 4836 #endif 4837 #ifdef CONFIG_B43_SSB 4838 case B43_BUS_SSB: 4839 ssb_pcicore_dev_irqvecs_enable(&dev->dev->sdev->bus->pcicore, 4840 dev->dev->sdev); 4841 break; 4842 #endif 4843 } 4844 4845 b43_imcfglo_timeouts_workaround(dev); 4846 b43_bluetooth_coext_disable(dev); 4847 if (phy->ops->prepare_hardware) { 4848 err = phy->ops->prepare_hardware(dev); 4849 if (err) 4850 goto err_busdown; 4851 } 4852 err = b43_chip_init(dev); 4853 if (err) 4854 goto err_busdown; 4855 b43_shm_write16(dev, B43_SHM_SHARED, 4856 B43_SHM_SH_WLCOREREV, dev->dev->core_rev); 4857 hf = b43_hf_read(dev); 4858 if (phy->type == B43_PHYTYPE_G) { 4859 hf |= B43_HF_SYMW; 4860 if (phy->rev == 1) 4861 hf |= B43_HF_GDCW; 4862 if (sprom->boardflags_lo & B43_BFL_PACTRL) 4863 hf |= B43_HF_OFDMPABOOST; 4864 } 4865 if (phy->radio_ver == 0x2050) { 4866 if (phy->radio_rev == 6) 4867 hf |= B43_HF_4318TSSI; 4868 if (phy->radio_rev < 6) 4869 hf |= B43_HF_VCORECALC; 4870 } 4871 if (sprom->boardflags_lo & B43_BFL_XTAL_NOSLOW) 4872 hf |= B43_HF_DSCRQ; /* Disable slowclock requests from ucode. */ 4873 #if defined(CONFIG_B43_SSB) && defined(CONFIG_SSB_DRIVER_PCICORE) 4874 if (dev->dev->bus_type == B43_BUS_SSB && 4875 dev->dev->sdev->bus->bustype == SSB_BUSTYPE_PCI && 4876 dev->dev->sdev->bus->pcicore.dev->id.revision <= 10) 4877 hf |= B43_HF_PCISCW; /* PCI slow clock workaround. */ 4878 #endif 4879 hf &= ~B43_HF_SKCFPUP; 4880 b43_hf_write(dev, hf); 4881 4882 /* tell the ucode MAC capabilities */ 4883 if (dev->dev->core_rev >= 13) { 4884 u32 mac_hw_cap = b43_read32(dev, B43_MMIO_MAC_HW_CAP); 4885 4886 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_MACHW_L, 4887 mac_hw_cap & 0xffff); 4888 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_MACHW_H, 4889 (mac_hw_cap >> 16) & 0xffff); 4890 } 4891 4892 b43_set_retry_limits(dev, B43_DEFAULT_SHORT_RETRY_LIMIT, 4893 B43_DEFAULT_LONG_RETRY_LIMIT); 4894 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_SFFBLIM, 3); 4895 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_LFFBLIM, 2); 4896 4897 /* Disable sending probe responses from firmware. 4898 * Setting the MaxTime to one usec will always trigger 4899 * a timeout, so we never send any probe resp. 4900 * A timeout of zero is infinite. */ 4901 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_PRMAXTIME, 1); 4902 4903 b43_rate_memory_init(dev); 4904 b43_set_phytxctl_defaults(dev); 4905 4906 /* Minimum Contention Window */ 4907 if (phy->type == B43_PHYTYPE_B) 4908 b43_shm_write16(dev, B43_SHM_SCRATCH, B43_SHM_SC_MINCONT, 0x1F); 4909 else 4910 b43_shm_write16(dev, B43_SHM_SCRATCH, B43_SHM_SC_MINCONT, 0xF); 4911 /* Maximum Contention Window */ 4912 b43_shm_write16(dev, B43_SHM_SCRATCH, B43_SHM_SC_MAXCONT, 0x3FF); 4913 4914 /* write phytype and phyvers */ 4915 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_PHYTYPE, phy->type); 4916 b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_PHYVER, phy->rev); 4917 4918 if (b43_bus_host_is_pcmcia(dev->dev) || 4919 b43_bus_host_is_sdio(dev->dev)) { 4920 dev->__using_pio_transfers = true; 4921 err = b43_pio_init(dev); 4922 } else if (dev->use_pio) { 4923 b43warn(dev->wl, "Forced PIO by use_pio module parameter. " 4924 "This should not be needed and will result in lower " 4925 "performance.\n"); 4926 dev->__using_pio_transfers = true; 4927 err = b43_pio_init(dev); 4928 } else { 4929 dev->__using_pio_transfers = false; 4930 err = b43_dma_init(dev); 4931 } 4932 if (err) 4933 goto err_chip_exit; 4934 b43_qos_init(dev); 4935 b43_set_synth_pu_delay(dev, 1); 4936 b43_bluetooth_coext_enable(dev); 4937 4938 b43_bus_powerup(dev, !(sprom->boardflags_lo & B43_BFL_XTAL_NOSLOW)); 4939 b43_upload_card_macaddress(dev); 4940 b43_security_init(dev); 4941 4942 ieee80211_wake_queues(dev->wl->hw); 4943 4944 b43_set_status(dev, B43_STAT_INITIALIZED); 4945 4946 out: 4947 return err; 4948 4949 err_chip_exit: 4950 b43_chip_exit(dev); 4951 err_busdown: 4952 b43_bus_may_powerdown(dev); 4953 B43_WARN_ON(b43_status(dev) != B43_STAT_UNINIT); 4954 return err; 4955 } 4956 4957 static int b43_op_add_interface(struct ieee80211_hw *hw, 4958 struct ieee80211_vif *vif) 4959 { 4960 struct b43_wl *wl = hw_to_b43_wl(hw); 4961 struct b43_wldev *dev; 4962 int err = -EOPNOTSUPP; 4963 4964 /* TODO: allow AP devices to coexist */ 4965 4966 if (vif->type != NL80211_IFTYPE_AP && 4967 vif->type != NL80211_IFTYPE_MESH_POINT && 4968 vif->type != NL80211_IFTYPE_STATION && 4969 vif->type != NL80211_IFTYPE_ADHOC) 4970 return -EOPNOTSUPP; 4971 4972 mutex_lock(&wl->mutex); 4973 if (wl->operating) 4974 goto out_mutex_unlock; 4975 4976 b43dbg(wl, "Adding Interface type %d\n", vif->type); 4977 4978 dev = wl->current_dev; 4979 wl->operating = true; 4980 wl->vif = vif; 4981 wl->if_type = vif->type; 4982 memcpy(wl->mac_addr, vif->addr, ETH_ALEN); 4983 4984 b43_adjust_opmode(dev); 4985 b43_set_pretbtt(dev); 4986 b43_set_synth_pu_delay(dev, 0); 4987 b43_upload_card_macaddress(dev); 4988 4989 err = 0; 4990 out_mutex_unlock: 4991 mutex_unlock(&wl->mutex); 4992 4993 if (err == 0) 4994 b43_op_bss_info_changed(hw, vif, &vif->bss_conf, ~0); 4995 4996 return err; 4997 } 4998 4999 static void b43_op_remove_interface(struct ieee80211_hw *hw, 5000 struct ieee80211_vif *vif) 5001 { 5002 struct b43_wl *wl = hw_to_b43_wl(hw); 5003 struct b43_wldev *dev = wl->current_dev; 5004 5005 b43dbg(wl, "Removing Interface type %d\n", vif->type); 5006 5007 mutex_lock(&wl->mutex); 5008 5009 B43_WARN_ON(!wl->operating); 5010 B43_WARN_ON(wl->vif != vif); 5011 wl->vif = NULL; 5012 5013 wl->operating = false; 5014 5015 b43_adjust_opmode(dev); 5016 eth_zero_addr(wl->mac_addr); 5017 b43_upload_card_macaddress(dev); 5018 5019 mutex_unlock(&wl->mutex); 5020 } 5021 5022 static int b43_op_start(struct ieee80211_hw *hw) 5023 { 5024 struct b43_wl *wl = hw_to_b43_wl(hw); 5025 struct b43_wldev *dev = wl->current_dev; 5026 int did_init = 0; 5027 int err = 0; 5028 5029 /* Kill all old instance specific information to make sure 5030 * the card won't use it in the short timeframe between start 5031 * and mac80211 reconfiguring it. */ 5032 eth_zero_addr(wl->bssid); 5033 eth_zero_addr(wl->mac_addr); 5034 wl->filter_flags = 0; 5035 wl->radiotap_enabled = false; 5036 b43_qos_clear(wl); 5037 wl->beacon0_uploaded = false; 5038 wl->beacon1_uploaded = false; 5039 wl->beacon_templates_virgin = true; 5040 wl->radio_enabled = true; 5041 5042 mutex_lock(&wl->mutex); 5043 5044 if (b43_status(dev) < B43_STAT_INITIALIZED) { 5045 err = b43_wireless_core_init(dev); 5046 if (err) 5047 goto out_mutex_unlock; 5048 did_init = 1; 5049 } 5050 5051 if (b43_status(dev) < B43_STAT_STARTED) { 5052 err = b43_wireless_core_start(dev); 5053 if (err) { 5054 if (did_init) 5055 b43_wireless_core_exit(dev); 5056 goto out_mutex_unlock; 5057 } 5058 } 5059 5060 /* XXX: only do if device doesn't support rfkill irq */ 5061 wiphy_rfkill_start_polling(hw->wiphy); 5062 5063 out_mutex_unlock: 5064 mutex_unlock(&wl->mutex); 5065 5066 /* 5067 * Configuration may have been overwritten during initialization. 5068 * Reload the configuration, but only if initialization was 5069 * successful. Reloading the configuration after a failed init 5070 * may hang the system. 5071 */ 5072 if (!err) 5073 b43_op_config(hw, ~0); 5074 5075 return err; 5076 } 5077 5078 static void b43_op_stop(struct ieee80211_hw *hw) 5079 { 5080 struct b43_wl *wl = hw_to_b43_wl(hw); 5081 struct b43_wldev *dev = wl->current_dev; 5082 5083 cancel_work_sync(&(wl->beacon_update_trigger)); 5084 5085 if (!dev) 5086 goto out; 5087 5088 mutex_lock(&wl->mutex); 5089 if (b43_status(dev) >= B43_STAT_STARTED) { 5090 dev = b43_wireless_core_stop(dev); 5091 if (!dev) 5092 goto out_unlock; 5093 } 5094 b43_wireless_core_exit(dev); 5095 wl->radio_enabled = false; 5096 5097 out_unlock: 5098 mutex_unlock(&wl->mutex); 5099 out: 5100 cancel_work_sync(&(wl->txpower_adjust_work)); 5101 } 5102 5103 static int b43_op_beacon_set_tim(struct ieee80211_hw *hw, 5104 struct ieee80211_sta *sta, bool set) 5105 { 5106 struct b43_wl *wl = hw_to_b43_wl(hw); 5107 5108 b43_update_templates(wl); 5109 5110 return 0; 5111 } 5112 5113 static void b43_op_sta_notify(struct ieee80211_hw *hw, 5114 struct ieee80211_vif *vif, 5115 enum sta_notify_cmd notify_cmd, 5116 struct ieee80211_sta *sta) 5117 { 5118 struct b43_wl *wl = hw_to_b43_wl(hw); 5119 5120 B43_WARN_ON(!vif || wl->vif != vif); 5121 } 5122 5123 static void b43_op_sw_scan_start_notifier(struct ieee80211_hw *hw, 5124 struct ieee80211_vif *vif, 5125 const u8 *mac_addr) 5126 { 5127 struct b43_wl *wl = hw_to_b43_wl(hw); 5128 struct b43_wldev *dev; 5129 5130 mutex_lock(&wl->mutex); 5131 dev = wl->current_dev; 5132 if (dev && (b43_status(dev) >= B43_STAT_INITIALIZED)) { 5133 /* Disable CFP update during scan on other channels. */ 5134 b43_hf_write(dev, b43_hf_read(dev) | B43_HF_SKCFPUP); 5135 } 5136 mutex_unlock(&wl->mutex); 5137 } 5138 5139 static void b43_op_sw_scan_complete_notifier(struct ieee80211_hw *hw, 5140 struct ieee80211_vif *vif) 5141 { 5142 struct b43_wl *wl = hw_to_b43_wl(hw); 5143 struct b43_wldev *dev; 5144 5145 mutex_lock(&wl->mutex); 5146 dev = wl->current_dev; 5147 if (dev && (b43_status(dev) >= B43_STAT_INITIALIZED)) { 5148 /* Re-enable CFP update. */ 5149 b43_hf_write(dev, b43_hf_read(dev) & ~B43_HF_SKCFPUP); 5150 } 5151 mutex_unlock(&wl->mutex); 5152 } 5153 5154 static int b43_op_get_survey(struct ieee80211_hw *hw, int idx, 5155 struct survey_info *survey) 5156 { 5157 struct b43_wl *wl = hw_to_b43_wl(hw); 5158 struct b43_wldev *dev = wl->current_dev; 5159 struct ieee80211_conf *conf = &hw->conf; 5160 5161 if (idx != 0) 5162 return -ENOENT; 5163 5164 survey->channel = conf->chandef.chan; 5165 survey->filled = SURVEY_INFO_NOISE_DBM; 5166 survey->noise = dev->stats.link_noise; 5167 5168 return 0; 5169 } 5170 5171 static const struct ieee80211_ops b43_hw_ops = { 5172 .tx = b43_op_tx, 5173 .conf_tx = b43_op_conf_tx, 5174 .add_interface = b43_op_add_interface, 5175 .remove_interface = b43_op_remove_interface, 5176 .config = b43_op_config, 5177 .bss_info_changed = b43_op_bss_info_changed, 5178 .configure_filter = b43_op_configure_filter, 5179 .set_key = b43_op_set_key, 5180 .update_tkip_key = b43_op_update_tkip_key, 5181 .get_stats = b43_op_get_stats, 5182 .get_tsf = b43_op_get_tsf, 5183 .set_tsf = b43_op_set_tsf, 5184 .start = b43_op_start, 5185 .stop = b43_op_stop, 5186 .set_tim = b43_op_beacon_set_tim, 5187 .sta_notify = b43_op_sta_notify, 5188 .sw_scan_start = b43_op_sw_scan_start_notifier, 5189 .sw_scan_complete = b43_op_sw_scan_complete_notifier, 5190 .get_survey = b43_op_get_survey, 5191 .rfkill_poll = b43_rfkill_poll, 5192 }; 5193 5194 /* Hard-reset the chip. Do not call this directly. 5195 * Use b43_controller_restart() 5196 */ 5197 static void b43_chip_reset(struct work_struct *work) 5198 { 5199 struct b43_wldev *dev = 5200 container_of(work, struct b43_wldev, restart_work); 5201 struct b43_wl *wl = dev->wl; 5202 int err = 0; 5203 int prev_status; 5204 5205 mutex_lock(&wl->mutex); 5206 5207 prev_status = b43_status(dev); 5208 /* Bring the device down... */ 5209 if (prev_status >= B43_STAT_STARTED) { 5210 dev = b43_wireless_core_stop(dev); 5211 if (!dev) { 5212 err = -ENODEV; 5213 goto out; 5214 } 5215 } 5216 if (prev_status >= B43_STAT_INITIALIZED) 5217 b43_wireless_core_exit(dev); 5218 5219 /* ...and up again. */ 5220 if (prev_status >= B43_STAT_INITIALIZED) { 5221 err = b43_wireless_core_init(dev); 5222 if (err) 5223 goto out; 5224 } 5225 if (prev_status >= B43_STAT_STARTED) { 5226 err = b43_wireless_core_start(dev); 5227 if (err) { 5228 b43_wireless_core_exit(dev); 5229 goto out; 5230 } 5231 } 5232 out: 5233 if (err) 5234 wl->current_dev = NULL; /* Failed to init the dev. */ 5235 mutex_unlock(&wl->mutex); 5236 5237 if (err) { 5238 b43err(wl, "Controller restart FAILED\n"); 5239 return; 5240 } 5241 5242 /* reload configuration */ 5243 b43_op_config(wl->hw, ~0); 5244 if (wl->vif) 5245 b43_op_bss_info_changed(wl->hw, wl->vif, &wl->vif->bss_conf, ~0); 5246 5247 b43info(wl, "Controller restarted\n"); 5248 } 5249 5250 static int b43_setup_bands(struct b43_wldev *dev, 5251 bool have_2ghz_phy, bool have_5ghz_phy) 5252 { 5253 struct ieee80211_hw *hw = dev->wl->hw; 5254 struct b43_phy *phy = &dev->phy; 5255 bool limited_2g; 5256 bool limited_5g; 5257 5258 /* We don't support all 2 GHz channels on some devices */ 5259 limited_2g = phy->radio_ver == 0x2057 && 5260 (phy->radio_rev == 9 || phy->radio_rev == 14); 5261 limited_5g = phy->radio_ver == 0x2057 && 5262 phy->radio_rev == 9; 5263 5264 if (have_2ghz_phy) 5265 hw->wiphy->bands[NL80211_BAND_2GHZ] = limited_2g ? 5266 &b43_band_2ghz_limited : &b43_band_2GHz; 5267 if (dev->phy.type == B43_PHYTYPE_N) { 5268 if (have_5ghz_phy) 5269 hw->wiphy->bands[NL80211_BAND_5GHZ] = limited_5g ? 5270 &b43_band_5GHz_nphy_limited : 5271 &b43_band_5GHz_nphy; 5272 } else { 5273 if (have_5ghz_phy) 5274 hw->wiphy->bands[NL80211_BAND_5GHZ] = &b43_band_5GHz_aphy; 5275 } 5276 5277 dev->phy.supports_2ghz = have_2ghz_phy; 5278 dev->phy.supports_5ghz = have_5ghz_phy; 5279 5280 return 0; 5281 } 5282 5283 static void b43_wireless_core_detach(struct b43_wldev *dev) 5284 { 5285 /* We release firmware that late to not be required to re-request 5286 * is all the time when we reinit the core. */ 5287 b43_release_firmware(dev); 5288 b43_phy_free(dev); 5289 } 5290 5291 static void b43_supported_bands(struct b43_wldev *dev, bool *have_2ghz_phy, 5292 bool *have_5ghz_phy) 5293 { 5294 u16 dev_id = 0; 5295 5296 #ifdef CONFIG_B43_BCMA 5297 if (dev->dev->bus_type == B43_BUS_BCMA && 5298 dev->dev->bdev->bus->hosttype == BCMA_HOSTTYPE_PCI) 5299 dev_id = dev->dev->bdev->bus->host_pci->device; 5300 #endif 5301 #ifdef CONFIG_B43_SSB 5302 if (dev->dev->bus_type == B43_BUS_SSB && 5303 dev->dev->sdev->bus->bustype == SSB_BUSTYPE_PCI) 5304 dev_id = dev->dev->sdev->bus->host_pci->device; 5305 #endif 5306 /* Override with SPROM value if available */ 5307 if (dev->dev->bus_sprom->dev_id) 5308 dev_id = dev->dev->bus_sprom->dev_id; 5309 5310 /* Note: below IDs can be "virtual" (not maching e.g. real PCI ID) */ 5311 switch (dev_id) { 5312 case 0x4324: /* BCM4306 */ 5313 case 0x4312: /* BCM4311 */ 5314 case 0x4319: /* BCM4318 */ 5315 case 0x4328: /* BCM4321 */ 5316 case 0x432b: /* BCM4322 */ 5317 case 0x4350: /* BCM43222 */ 5318 case 0x4353: /* BCM43224 */ 5319 case 0x0576: /* BCM43224 */ 5320 case 0x435f: /* BCM6362 */ 5321 case 0x4331: /* BCM4331 */ 5322 case 0x4359: /* BCM43228 */ 5323 case 0x43a0: /* BCM4360 */ 5324 case 0x43b1: /* BCM4352 */ 5325 /* Dual band devices */ 5326 *have_2ghz_phy = true; 5327 *have_5ghz_phy = true; 5328 return; 5329 case 0x4321: /* BCM4306 */ 5330 /* There are 14e4:4321 PCI devs with 2.4 GHz BCM4321 (N-PHY) */ 5331 if (dev->phy.type != B43_PHYTYPE_G) 5332 break; 5333 fallthrough; 5334 case 0x4313: /* BCM4311 */ 5335 case 0x431a: /* BCM4318 */ 5336 case 0x432a: /* BCM4321 */ 5337 case 0x432d: /* BCM4322 */ 5338 case 0x4352: /* BCM43222 */ 5339 case 0x435a: /* BCM43228 */ 5340 case 0x4333: /* BCM4331 */ 5341 case 0x43a2: /* BCM4360 */ 5342 case 0x43b3: /* BCM4352 */ 5343 /* 5 GHz only devices */ 5344 *have_2ghz_phy = false; 5345 *have_5ghz_phy = true; 5346 return; 5347 } 5348 5349 /* As a fallback, try to guess using PHY type */ 5350 switch (dev->phy.type) { 5351 case B43_PHYTYPE_G: 5352 case B43_PHYTYPE_N: 5353 case B43_PHYTYPE_LP: 5354 case B43_PHYTYPE_HT: 5355 case B43_PHYTYPE_LCN: 5356 *have_2ghz_phy = true; 5357 *have_5ghz_phy = false; 5358 return; 5359 } 5360 5361 B43_WARN_ON(1); 5362 } 5363 5364 static int b43_wireless_core_attach(struct b43_wldev *dev) 5365 { 5366 struct b43_wl *wl = dev->wl; 5367 struct b43_phy *phy = &dev->phy; 5368 int err; 5369 u32 tmp; 5370 bool have_2ghz_phy = false, have_5ghz_phy = false; 5371 5372 /* Do NOT do any device initialization here. 5373 * Do it in wireless_core_init() instead. 5374 * This function is for gathering basic information about the HW, only. 5375 * Also some structs may be set up here. But most likely you want to have 5376 * that in core_init(), too. 5377 */ 5378 5379 err = b43_bus_powerup(dev, 0); 5380 if (err) { 5381 b43err(wl, "Bus powerup failed\n"); 5382 goto out; 5383 } 5384 5385 phy->do_full_init = true; 5386 5387 /* Try to guess supported bands for the first init needs */ 5388 switch (dev->dev->bus_type) { 5389 #ifdef CONFIG_B43_BCMA 5390 case B43_BUS_BCMA: 5391 tmp = bcma_aread32(dev->dev->bdev, BCMA_IOST); 5392 have_2ghz_phy = !!(tmp & B43_BCMA_IOST_2G_PHY); 5393 have_5ghz_phy = !!(tmp & B43_BCMA_IOST_5G_PHY); 5394 break; 5395 #endif 5396 #ifdef CONFIG_B43_SSB 5397 case B43_BUS_SSB: 5398 if (dev->dev->core_rev >= 5) { 5399 tmp = ssb_read32(dev->dev->sdev, SSB_TMSHIGH); 5400 have_2ghz_phy = !!(tmp & B43_TMSHIGH_HAVE_2GHZ_PHY); 5401 have_5ghz_phy = !!(tmp & B43_TMSHIGH_HAVE_5GHZ_PHY); 5402 } else 5403 B43_WARN_ON(1); 5404 break; 5405 #endif 5406 } 5407 5408 dev->phy.gmode = have_2ghz_phy; 5409 b43_wireless_core_reset(dev, dev->phy.gmode); 5410 5411 /* Get the PHY type. */ 5412 err = b43_phy_versioning(dev); 5413 if (err) 5414 goto err_powerdown; 5415 5416 /* Get real info about supported bands */ 5417 b43_supported_bands(dev, &have_2ghz_phy, &have_5ghz_phy); 5418 5419 /* We don't support 5 GHz on some PHYs yet */ 5420 if (have_5ghz_phy) { 5421 switch (dev->phy.type) { 5422 case B43_PHYTYPE_G: 5423 case B43_PHYTYPE_LP: 5424 case B43_PHYTYPE_HT: 5425 b43warn(wl, "5 GHz band is unsupported on this PHY\n"); 5426 have_5ghz_phy = false; 5427 } 5428 } 5429 5430 if (!have_2ghz_phy && !have_5ghz_phy) { 5431 b43err(wl, "b43 can't support any band on this device\n"); 5432 err = -EOPNOTSUPP; 5433 goto err_powerdown; 5434 } 5435 5436 err = b43_phy_allocate(dev); 5437 if (err) 5438 goto err_powerdown; 5439 5440 dev->phy.gmode = have_2ghz_phy; 5441 b43_wireless_core_reset(dev, dev->phy.gmode); 5442 5443 err = b43_validate_chipaccess(dev); 5444 if (err) 5445 goto err_phy_free; 5446 err = b43_setup_bands(dev, have_2ghz_phy, have_5ghz_phy); 5447 if (err) 5448 goto err_phy_free; 5449 5450 /* Now set some default "current_dev" */ 5451 if (!wl->current_dev) 5452 wl->current_dev = dev; 5453 INIT_WORK(&dev->restart_work, b43_chip_reset); 5454 5455 dev->phy.ops->switch_analog(dev, 0); 5456 b43_device_disable(dev, 0); 5457 b43_bus_may_powerdown(dev); 5458 5459 out: 5460 return err; 5461 5462 err_phy_free: 5463 b43_phy_free(dev); 5464 err_powerdown: 5465 b43_bus_may_powerdown(dev); 5466 return err; 5467 } 5468 5469 static void b43_one_core_detach(struct b43_bus_dev *dev) 5470 { 5471 struct b43_wldev *wldev; 5472 5473 /* Do not cancel ieee80211-workqueue based work here. 5474 * See comment in b43_remove(). */ 5475 5476 wldev = b43_bus_get_wldev(dev); 5477 b43_debugfs_remove_device(wldev); 5478 b43_wireless_core_detach(wldev); 5479 list_del(&wldev->list); 5480 b43_bus_set_wldev(dev, NULL); 5481 kfree(wldev); 5482 } 5483 5484 static int b43_one_core_attach(struct b43_bus_dev *dev, struct b43_wl *wl) 5485 { 5486 struct b43_wldev *wldev; 5487 int err = -ENOMEM; 5488 5489 wldev = kzalloc(sizeof(*wldev), GFP_KERNEL); 5490 if (!wldev) 5491 goto out; 5492 5493 wldev->use_pio = b43_modparam_pio; 5494 wldev->dev = dev; 5495 wldev->wl = wl; 5496 b43_set_status(wldev, B43_STAT_UNINIT); 5497 wldev->bad_frames_preempt = modparam_bad_frames_preempt; 5498 INIT_LIST_HEAD(&wldev->list); 5499 5500 err = b43_wireless_core_attach(wldev); 5501 if (err) 5502 goto err_kfree_wldev; 5503 5504 b43_bus_set_wldev(dev, wldev); 5505 b43_debugfs_add_device(wldev); 5506 5507 out: 5508 return err; 5509 5510 err_kfree_wldev: 5511 kfree(wldev); 5512 return err; 5513 } 5514 5515 #define IS_PDEV(pdev, _vendor, _device, _subvendor, _subdevice) ( \ 5516 (pdev->vendor == PCI_VENDOR_ID_##_vendor) && \ 5517 (pdev->device == _device) && \ 5518 (pdev->subsystem_vendor == PCI_VENDOR_ID_##_subvendor) && \ 5519 (pdev->subsystem_device == _subdevice) ) 5520 5521 #ifdef CONFIG_B43_SSB 5522 static void b43_sprom_fixup(struct ssb_bus *bus) 5523 { 5524 struct pci_dev *pdev; 5525 5526 /* boardflags workarounds */ 5527 if (bus->boardinfo.vendor == SSB_BOARDVENDOR_DELL && 5528 bus->chip_id == 0x4301 && bus->sprom.board_rev == 0x74) 5529 bus->sprom.boardflags_lo |= B43_BFL_BTCOEXIST; 5530 if (bus->boardinfo.vendor == PCI_VENDOR_ID_APPLE && 5531 bus->boardinfo.type == 0x4E && bus->sprom.board_rev > 0x40) 5532 bus->sprom.boardflags_lo |= B43_BFL_PACTRL; 5533 if (bus->bustype == SSB_BUSTYPE_PCI) { 5534 pdev = bus->host_pci; 5535 if (IS_PDEV(pdev, BROADCOM, 0x4318, ASUSTEK, 0x100F) || 5536 IS_PDEV(pdev, BROADCOM, 0x4320, DELL, 0x0003) || 5537 IS_PDEV(pdev, BROADCOM, 0x4320, HP, 0x12f8) || 5538 IS_PDEV(pdev, BROADCOM, 0x4320, LINKSYS, 0x0015) || 5539 IS_PDEV(pdev, BROADCOM, 0x4320, LINKSYS, 0x0014) || 5540 IS_PDEV(pdev, BROADCOM, 0x4320, LINKSYS, 0x0013) || 5541 IS_PDEV(pdev, BROADCOM, 0x4320, MOTOROLA, 0x7010)) 5542 bus->sprom.boardflags_lo &= ~B43_BFL_BTCOEXIST; 5543 } 5544 } 5545 5546 static void b43_wireless_exit(struct b43_bus_dev *dev, struct b43_wl *wl) 5547 { 5548 struct ieee80211_hw *hw = wl->hw; 5549 5550 ssb_set_devtypedata(dev->sdev, NULL); 5551 ieee80211_free_hw(hw); 5552 } 5553 #endif 5554 5555 static struct b43_wl *b43_wireless_init(struct b43_bus_dev *dev) 5556 { 5557 struct ssb_sprom *sprom = dev->bus_sprom; 5558 struct ieee80211_hw *hw; 5559 struct b43_wl *wl; 5560 char chip_name[6]; 5561 int queue_num; 5562 5563 hw = ieee80211_alloc_hw(sizeof(*wl), &b43_hw_ops); 5564 if (!hw) { 5565 b43err(NULL, "Could not allocate ieee80211 device\n"); 5566 return ERR_PTR(-ENOMEM); 5567 } 5568 wl = hw_to_b43_wl(hw); 5569 5570 /* fill hw info */ 5571 ieee80211_hw_set(hw, RX_INCLUDES_FCS); 5572 ieee80211_hw_set(hw, SIGNAL_DBM); 5573 ieee80211_hw_set(hw, MFP_CAPABLE); 5574 hw->wiphy->interface_modes = 5575 BIT(NL80211_IFTYPE_AP) | 5576 BIT(NL80211_IFTYPE_MESH_POINT) | 5577 BIT(NL80211_IFTYPE_STATION) | 5578 BIT(NL80211_IFTYPE_ADHOC); 5579 5580 hw->wiphy->flags |= WIPHY_FLAG_IBSS_RSN; 5581 5582 wiphy_ext_feature_set(hw->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST); 5583 5584 wl->hw_registered = false; 5585 hw->max_rates = 2; 5586 SET_IEEE80211_DEV(hw, dev->dev); 5587 if (is_valid_ether_addr(sprom->et1mac)) 5588 SET_IEEE80211_PERM_ADDR(hw, sprom->et1mac); 5589 else 5590 SET_IEEE80211_PERM_ADDR(hw, sprom->il0mac); 5591 5592 /* Initialize struct b43_wl */ 5593 wl->hw = hw; 5594 mutex_init(&wl->mutex); 5595 spin_lock_init(&wl->hardirq_lock); 5596 spin_lock_init(&wl->beacon_lock); 5597 INIT_WORK(&wl->beacon_update_trigger, b43_beacon_update_trigger_work); 5598 INIT_WORK(&wl->txpower_adjust_work, b43_phy_txpower_adjust_work); 5599 INIT_WORK(&wl->tx_work, b43_tx_work); 5600 5601 /* Initialize queues and flags. */ 5602 for (queue_num = 0; queue_num < B43_QOS_QUEUE_NUM; queue_num++) { 5603 skb_queue_head_init(&wl->tx_queue[queue_num]); 5604 wl->tx_queue_stopped[queue_num] = false; 5605 } 5606 5607 snprintf(chip_name, ARRAY_SIZE(chip_name), 5608 (dev->chip_id > 0x9999) ? "%d" : "%04X", dev->chip_id); 5609 b43info(wl, "Broadcom %s WLAN found (core revision %u)\n", chip_name, 5610 dev->core_rev); 5611 return wl; 5612 } 5613 5614 #ifdef CONFIG_B43_BCMA 5615 static int b43_bcma_probe(struct bcma_device *core) 5616 { 5617 struct b43_bus_dev *dev; 5618 struct b43_wl *wl; 5619 int err; 5620 5621 if (!modparam_allhwsupport && 5622 (core->id.rev == 0x17 || core->id.rev == 0x18)) { 5623 pr_err("Support for cores revisions 0x17 and 0x18 disabled by module param allhwsupport=0. Try b43.allhwsupport=1\n"); 5624 return -ENOTSUPP; 5625 } 5626 5627 dev = b43_bus_dev_bcma_init(core); 5628 if (!dev) 5629 return -ENODEV; 5630 5631 wl = b43_wireless_init(dev); 5632 if (IS_ERR(wl)) { 5633 err = PTR_ERR(wl); 5634 goto bcma_out; 5635 } 5636 5637 err = b43_one_core_attach(dev, wl); 5638 if (err) 5639 goto bcma_err_wireless_exit; 5640 5641 /* setup and start work to load firmware */ 5642 INIT_WORK(&wl->firmware_load, b43_request_firmware); 5643 schedule_work(&wl->firmware_load); 5644 5645 return err; 5646 5647 bcma_err_wireless_exit: 5648 ieee80211_free_hw(wl->hw); 5649 bcma_out: 5650 kfree(dev); 5651 return err; 5652 } 5653 5654 static void b43_bcma_remove(struct bcma_device *core) 5655 { 5656 struct b43_wldev *wldev = bcma_get_drvdata(core); 5657 struct b43_wl *wl = wldev->wl; 5658 5659 /* We must cancel any work here before unregistering from ieee80211, 5660 * as the ieee80211 unreg will destroy the workqueue. */ 5661 cancel_work_sync(&wldev->restart_work); 5662 cancel_work_sync(&wl->firmware_load); 5663 5664 B43_WARN_ON(!wl); 5665 if (!wldev->fw.ucode.data) 5666 return; /* NULL if firmware never loaded */ 5667 if (wl->current_dev == wldev && wl->hw_registered) { 5668 b43_leds_stop(wldev); 5669 ieee80211_unregister_hw(wl->hw); 5670 } 5671 5672 b43_one_core_detach(wldev->dev); 5673 5674 /* Unregister HW RNG driver */ 5675 b43_rng_exit(wl); 5676 5677 b43_leds_unregister(wl); 5678 ieee80211_free_hw(wl->hw); 5679 kfree(wldev->dev); 5680 } 5681 5682 static struct bcma_driver b43_bcma_driver = { 5683 .name = KBUILD_MODNAME, 5684 .id_table = b43_bcma_tbl, 5685 .probe = b43_bcma_probe, 5686 .remove = b43_bcma_remove, 5687 }; 5688 #endif 5689 5690 #ifdef CONFIG_B43_SSB 5691 static 5692 int b43_ssb_probe(struct ssb_device *sdev, const struct ssb_device_id *id) 5693 { 5694 struct b43_bus_dev *dev; 5695 struct b43_wl *wl; 5696 int err; 5697 5698 dev = b43_bus_dev_ssb_init(sdev); 5699 if (!dev) 5700 return -ENOMEM; 5701 5702 wl = ssb_get_devtypedata(sdev); 5703 if (wl) { 5704 b43err(NULL, "Dual-core devices are not supported\n"); 5705 err = -ENOTSUPP; 5706 goto err_ssb_kfree_dev; 5707 } 5708 5709 b43_sprom_fixup(sdev->bus); 5710 5711 wl = b43_wireless_init(dev); 5712 if (IS_ERR(wl)) { 5713 err = PTR_ERR(wl); 5714 goto err_ssb_kfree_dev; 5715 } 5716 ssb_set_devtypedata(sdev, wl); 5717 B43_WARN_ON(ssb_get_devtypedata(sdev) != wl); 5718 5719 err = b43_one_core_attach(dev, wl); 5720 if (err) 5721 goto err_ssb_wireless_exit; 5722 5723 /* setup and start work to load firmware */ 5724 INIT_WORK(&wl->firmware_load, b43_request_firmware); 5725 schedule_work(&wl->firmware_load); 5726 5727 return err; 5728 5729 err_ssb_wireless_exit: 5730 b43_wireless_exit(dev, wl); 5731 err_ssb_kfree_dev: 5732 kfree(dev); 5733 return err; 5734 } 5735 5736 static void b43_ssb_remove(struct ssb_device *sdev) 5737 { 5738 struct b43_wl *wl = ssb_get_devtypedata(sdev); 5739 struct b43_wldev *wldev = ssb_get_drvdata(sdev); 5740 struct b43_bus_dev *dev = wldev->dev; 5741 5742 /* We must cancel any work here before unregistering from ieee80211, 5743 * as the ieee80211 unreg will destroy the workqueue. */ 5744 cancel_work_sync(&wldev->restart_work); 5745 cancel_work_sync(&wl->firmware_load); 5746 5747 B43_WARN_ON(!wl); 5748 if (!wldev->fw.ucode.data) 5749 return; /* NULL if firmware never loaded */ 5750 if (wl->current_dev == wldev && wl->hw_registered) { 5751 b43_leds_stop(wldev); 5752 ieee80211_unregister_hw(wl->hw); 5753 } 5754 5755 b43_one_core_detach(dev); 5756 5757 /* Unregister HW RNG driver */ 5758 b43_rng_exit(wl); 5759 5760 b43_leds_unregister(wl); 5761 b43_wireless_exit(dev, wl); 5762 kfree(dev); 5763 } 5764 5765 static struct ssb_driver b43_ssb_driver = { 5766 .name = KBUILD_MODNAME, 5767 .id_table = b43_ssb_tbl, 5768 .probe = b43_ssb_probe, 5769 .remove = b43_ssb_remove, 5770 }; 5771 #endif /* CONFIG_B43_SSB */ 5772 5773 /* Perform a hardware reset. This can be called from any context. */ 5774 void b43_controller_restart(struct b43_wldev *dev, const char *reason) 5775 { 5776 /* Must avoid requeueing, if we are in shutdown. */ 5777 if (b43_status(dev) < B43_STAT_INITIALIZED) 5778 return; 5779 b43info(dev->wl, "Controller RESET (%s) ...\n", reason); 5780 ieee80211_queue_work(dev->wl->hw, &dev->restart_work); 5781 } 5782 5783 static void b43_print_driverinfo(void) 5784 { 5785 const char *feat_pci = "", *feat_pcmcia = "", *feat_nphy = "", 5786 *feat_leds = "", *feat_sdio = ""; 5787 5788 #ifdef CONFIG_B43_PCI_AUTOSELECT 5789 feat_pci = "P"; 5790 #endif 5791 #ifdef CONFIG_B43_PCMCIA 5792 feat_pcmcia = "M"; 5793 #endif 5794 #ifdef CONFIG_B43_PHY_N 5795 feat_nphy = "N"; 5796 #endif 5797 #ifdef CONFIG_B43_LEDS 5798 feat_leds = "L"; 5799 #endif 5800 #ifdef CONFIG_B43_SDIO 5801 feat_sdio = "S"; 5802 #endif 5803 printk(KERN_INFO "Broadcom 43xx driver loaded " 5804 "[ Features: %s%s%s%s%s ]\n", 5805 feat_pci, feat_pcmcia, feat_nphy, 5806 feat_leds, feat_sdio); 5807 } 5808 5809 static int __init b43_init(void) 5810 { 5811 int err; 5812 5813 b43_debugfs_init(); 5814 err = b43_sdio_init(); 5815 if (err) 5816 goto err_dfs_exit; 5817 #ifdef CONFIG_B43_BCMA 5818 err = bcma_driver_register(&b43_bcma_driver); 5819 if (err) 5820 goto err_sdio_exit; 5821 #endif 5822 #ifdef CONFIG_B43_SSB 5823 err = ssb_driver_register(&b43_ssb_driver); 5824 if (err) 5825 goto err_bcma_driver_exit; 5826 #endif 5827 b43_print_driverinfo(); 5828 5829 return err; 5830 5831 #ifdef CONFIG_B43_SSB 5832 err_bcma_driver_exit: 5833 #endif 5834 #ifdef CONFIG_B43_BCMA 5835 bcma_driver_unregister(&b43_bcma_driver); 5836 err_sdio_exit: 5837 #endif 5838 b43_sdio_exit(); 5839 err_dfs_exit: 5840 b43_debugfs_exit(); 5841 return err; 5842 } 5843 5844 static void __exit b43_exit(void) 5845 { 5846 #ifdef CONFIG_B43_SSB 5847 ssb_driver_unregister(&b43_ssb_driver); 5848 #endif 5849 #ifdef CONFIG_B43_BCMA 5850 bcma_driver_unregister(&b43_bcma_driver); 5851 #endif 5852 b43_sdio_exit(); 5853 b43_debugfs_exit(); 5854 } 5855 5856 module_init(b43_init) 5857 module_exit(b43_exit) 5858