xref: /openbmc/linux/drivers/net/wireless/ath/wil6210/main.c (revision 520d68e7)

/*
 * Copyright (c) 2012-2014 Qualcomm Atheros, Inc.
 *
 * Permission to use, copy, modify, and/or distribute this software for any
 * purpose with or without fee is hereby granted, provided that the above
 * copyright notice and this permission notice appear in all copies.
 *
 * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
 * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
 * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
 * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
 * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
 * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
 * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
 */

#include <linux/moduleparam.h>
#include <linux/if_arp.h>
#include <linux/etherdevice.h>

#include "wil6210.h"
#include "txrx.h"

static bool no_fw_recovery;
module_param(no_fw_recovery, bool, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(no_fw_recovery, " disable FW error recovery");

#define RST_DELAY (20) /* msec, for loop in @wil_target_reset */
#define RST_COUNT (1 + 1000/RST_DELAY) /* round up to be above 1 sec total */

/*
 * Due to a hardware issue,
 * one has to read/write to/from NIC in 32-bit chunks;
 * regular memcpy_fromio and siblings will
 * not work on 64-bit platform - it uses 64-bit transactions
 *
 * Force 32-bit transactions to enable NIC on 64-bit platforms
 *
 * To avoid byte swap on big endian host, __raw_{read|write}l
 * should be used - {read|write}l would swap bytes to provide
 * little endian on PCI value in host endianness.
 */
void wil_memcpy_fromio_32(void *dst, const volatile void __iomem *src,
			  size_t count)
{
	u32 *d = dst;
	const volatile u32 __iomem *s = src;

	/* size_t is unsigned, if (count%4 != 0) it will wrap */
	for (count += 4; count > 4; count -= 4)
		*d++ = __raw_readl(s++);
}

void wil_memcpy_toio_32(volatile void __iomem *dst, const void *src,
			size_t count)
{
	volatile u32 __iomem *d = dst;
	const u32 *s = src;

	for (count += 4; count > 4; count -= 4)
		__raw_writel(*s++, d++);
}

static void wil_disconnect_cid(struct wil6210_priv *wil, int cid)
{
	uint i;
	struct net_device *ndev = wil_to_ndev(wil);
	struct wireless_dev *wdev = wil->wdev;
	struct wil_sta_info *sta = &wil->sta[cid];
	wil_dbg_misc(wil, "%s(CID %d, status %d)\n", __func__, cid,
		     sta->status);

	sta->data_port_open = false;
	if (sta->status != wil_sta_unused) {
		wmi_disconnect_sta(wil, sta->addr, WLAN_REASON_DEAUTH_LEAVING);
		switch (wdev->iftype) {
		case NL80211_IFTYPE_AP:
		case NL80211_IFTYPE_P2P_GO:
			/* AP-like interface */
			cfg80211_del_sta(ndev, sta->addr, GFP_KERNEL);
			break;
		default:
			break;
		}
		sta->status = wil_sta_unused;
	}

	for (i = 0; i < WIL_STA_TID_NUM; i++) {
		struct wil_tid_ampdu_rx *r = sta->tid_rx[i];
		sta->tid_rx[i] = NULL;
		wil_tid_ampdu_rx_free(wil, r);
	}
	for (i = 0; i < ARRAY_SIZE(wil->vring_tx); i++) {
		if (wil->vring2cid_tid[i][0] == cid)
			wil_vring_fini_tx(wil, i);
	}
	memset(&sta->stats, 0, sizeof(sta->stats));
}

static void _wil6210_disconnect(struct wil6210_priv *wil, const u8 *bssid)
{
	int cid = -ENOENT;
	struct net_device *ndev = wil_to_ndev(wil);
	struct wireless_dev *wdev = wil->wdev;

	might_sleep();
	if (bssid) {
		cid = wil_find_cid(wil, bssid);
		wil_dbg_misc(wil, "%s(%pM, CID %d)\n", __func__, bssid, cid);
	} else {
		wil_dbg_misc(wil, "%s(all)\n", __func__);
	}

	if (cid >= 0) /* disconnect 1 peer */
		wil_disconnect_cid(wil, cid);
	else /* disconnect all */
		for (cid = 0; cid < WIL6210_MAX_CID; cid++)
			wil_disconnect_cid(wil, cid);

	/* link state */
	switch (wdev->iftype) {
	case NL80211_IFTYPE_STATION:
	case NL80211_IFTYPE_P2P_CLIENT:
		wil_link_off(wil);
		if (test_bit(wil_status_fwconnected, &wil->status)) {
			clear_bit(wil_status_fwconnected, &wil->status);
			cfg80211_disconnected(ndev,
					      WLAN_STATUS_UNSPECIFIED_FAILURE,
					      NULL, 0, GFP_KERNEL);
		} else if (test_bit(wil_status_fwconnecting, &wil->status)) {
			cfg80211_connect_result(ndev, bssid, NULL, 0, NULL, 0,
						WLAN_STATUS_UNSPECIFIED_FAILURE,
						GFP_KERNEL);
		}
		clear_bit(wil_status_fwconnecting, &wil->status);
		break;
	default:
		break;
	}
}

static void wil_disconnect_worker(struct work_struct *work)
{
	struct wil6210_priv *wil = container_of(work,
			struct wil6210_priv, disconnect_worker);

	mutex_lock(&wil->mutex);
	_wil6210_disconnect(wil, NULL);
	mutex_unlock(&wil->mutex);
}

static void wil_connect_timer_fn(ulong x)
{
	struct wil6210_priv *wil = (void *)x;

	wil_dbg_misc(wil, "Connect timeout\n");

	/* reschedule to thread context - disconnect won't
	 * run from atomic context
	 */
	schedule_work(&wil->disconnect_worker);
}

static void wil_scan_timer_fn(ulong x)
{
	struct wil6210_priv *wil = (void *)x;

	clear_bit(wil_status_fwready, &wil->status);
	wil_err(wil, "Scan timeout detected, start fw error recovery\n");
	schedule_work(&wil->fw_error_worker);
}

static void wil_fw_error_worker(struct work_struct *work)
{
	struct wil6210_priv *wil = container_of(work,
			struct wil6210_priv, fw_error_worker);
	struct wireless_dev *wdev = wil->wdev;

	wil_dbg_misc(wil, "fw error worker\n");

	if (no_fw_recovery)
		return;

	/* increment @recovery_count if less then WIL6210_FW_RECOVERY_TO
	 * passed since last recovery attempt
	 */
	if (time_is_after_jiffies(wil->last_fw_recovery +
				  WIL6210_FW_RECOVERY_TO))
		wil->recovery_count++;
	else
		wil->recovery_count = 1; /* fw was alive for a long time */

	if (wil->recovery_count > WIL6210_FW_RECOVERY_RETRIES) {
		wil_err(wil, "too many recovery attempts (%d), giving up\n",
			wil->recovery_count);
		return;
	}

	wil->last_fw_recovery = jiffies;

	mutex_lock(&wil->mutex);
	switch (wdev->iftype) {
	case NL80211_IFTYPE_STATION:
	case NL80211_IFTYPE_P2P_CLIENT:
	case NL80211_IFTYPE_MONITOR:
		wil_info(wil, "fw error recovery started (try %d)...\n",
			 wil->recovery_count);
		wil_reset(wil);

		/* need to re-allocate Rx ring after reset */
		wil_rx_init(wil);
		break;
	case NL80211_IFTYPE_AP:
	case NL80211_IFTYPE_P2P_GO:
		/* recovery in these modes is done by upper layers */
		break;
	default:
		break;
	}
	mutex_unlock(&wil->mutex);
}

static int wil_find_free_vring(struct wil6210_priv *wil)
{
	int i;
	for (i = 0; i < WIL6210_MAX_TX_RINGS; i++) {
		if (!wil->vring_tx[i].va)
			return i;
	}
	return -EINVAL;
}

static void wil_connect_worker(struct work_struct *work)
{
	int rc;
	struct wil6210_priv *wil = container_of(work, struct wil6210_priv,
						connect_worker);
	int cid = wil->pending_connect_cid;
	int ringid = wil_find_free_vring(wil);

	if (cid < 0) {
		wil_err(wil, "No connection pending\n");
		return;
	}

	wil_dbg_wmi(wil, "Configure for connection CID %d\n", cid);

	rc = wil_vring_init_tx(wil, ringid, WIL6210_TX_RING_SIZE, cid, 0);
	wil->pending_connect_cid = -1;
	if (rc == 0) {
		wil->sta[cid].status = wil_sta_connected;
		wil_link_on(wil);
	} else {
		wil->sta[cid].status = wil_sta_unused;
	}
}

int wil_priv_init(struct wil6210_priv *wil)
{
	wil_dbg_misc(wil, "%s()\n", __func__);

	memset(wil->sta, 0, sizeof(wil->sta));

	mutex_init(&wil->mutex);
	mutex_init(&wil->wmi_mutex);

	init_completion(&wil->wmi_ready);

	wil->pending_connect_cid = -1;
	setup_timer(&wil->connect_timer, wil_connect_timer_fn, (ulong)wil);
	setup_timer(&wil->scan_timer, wil_scan_timer_fn, (ulong)wil);

	INIT_WORK(&wil->connect_worker, wil_connect_worker);
	INIT_WORK(&wil->disconnect_worker, wil_disconnect_worker);
	INIT_WORK(&wil->wmi_event_worker, wmi_event_worker);
	INIT_WORK(&wil->fw_error_worker, wil_fw_error_worker);

	INIT_LIST_HEAD(&wil->pending_wmi_ev);
	spin_lock_init(&wil->wmi_ev_lock);

	wil->wmi_wq = create_singlethread_workqueue(WIL_NAME"_wmi");
	if (!wil->wmi_wq)
		return -EAGAIN;

	wil->wmi_wq_conn = create_singlethread_workqueue(WIL_NAME"_connect");
	if (!wil->wmi_wq_conn) {
		destroy_workqueue(wil->wmi_wq);
		return -EAGAIN;
	}

	wil->last_fw_recovery = jiffies;

	return 0;
}

void wil6210_disconnect(struct wil6210_priv *wil, const u8 *bssid)
{
	del_timer_sync(&wil->connect_timer);
	_wil6210_disconnect(wil, bssid);
}

void wil_priv_deinit(struct wil6210_priv *wil)
{
	del_timer_sync(&wil->scan_timer);
	cancel_work_sync(&wil->disconnect_worker);
	cancel_work_sync(&wil->fw_error_worker);
	mutex_lock(&wil->mutex);
	wil6210_disconnect(wil, NULL);
	mutex_unlock(&wil->mutex);
	wmi_event_flush(wil);
	destroy_workqueue(wil->wmi_wq_conn);
	destroy_workqueue(wil->wmi_wq);
}

static int wil_target_reset(struct wil6210_priv *wil)
{
	int delay = 0;
	u32 hw_state;
	u32 rev_id;
	bool is_sparrow = (wil->board->board == WIL_BOARD_SPARROW);

	wil_dbg_misc(wil, "Resetting \"%s\"...\n", wil->board->name);

	/* register read */
#define R(a) ioread32(wil->csr + HOSTADDR(a))
	/* register write */
#define W(a, v) iowrite32(v, wil->csr + HOSTADDR(a))
	/* register set = read, OR, write */
#define S(a, v) W(a, R(a) | v)
	/* register clear = read, AND with inverted, write */
#define C(a, v) W(a, R(a) & ~v)

	wmb(); /* If host reorder writes here -> race in NIC */
	W(RGF_USER_MAC_CPU_0,  BIT(1)); /* mac_cpu_man_rst */
	wil->hw_version = R(RGF_USER_FW_REV_ID);
	rev_id = wil->hw_version & 0xff;

	/* Clear MAC link up */
	S(RGF_HP_CTRL, BIT(15));
	/* hpal_perst_from_pad_src_n_mask */
	S(RGF_USER_CLKS_CTL_SW_RST_MASK_0, BIT(6));
	/* car_perst_rst_src_n_mask */
	S(RGF_USER_CLKS_CTL_SW_RST_MASK_0, BIT(7));
	wmb(); /* order is important here */

	if (is_sparrow) {
		W(RGF_USER_CLKS_CTL_EXT_SW_RST_VEC_0, 0x3ff81f);
		wmb(); /* order is important here */
	}

	W(RGF_USER_USER_CPU_0, BIT(1)); /* user_cpu_man_rst */
	wmb(); /* If host reorder writes here -> race in NIC */
	W(RGF_USER_MAC_CPU_0,  BIT(1)); /* mac_cpu_man_rst */
	wmb(); /* order is important here */

	W(RGF_USER_CLKS_CTL_SW_RST_VEC_2, 0xFE000000);
	W(RGF_USER_CLKS_CTL_SW_RST_VEC_1, 0x0000003F);
	W(RGF_USER_CLKS_CTL_SW_RST_VEC_3, is_sparrow ? 0x000000B0 : 0x00000170);
	W(RGF_USER_CLKS_CTL_SW_RST_VEC_0, 0xFFE7FC00);
	wmb(); /* order is important here */

	if (is_sparrow) {
		W(RGF_USER_CLKS_CTL_EXT_SW_RST_VEC_0, 0x0);
		wmb(); /* order is important here */
	}

	W(RGF_USER_CLKS_CTL_SW_RST_VEC_3, 0);
	W(RGF_USER_CLKS_CTL_SW_RST_VEC_2, 0);
	W(RGF_USER_CLKS_CTL_SW_RST_VEC_1, 0);
	W(RGF_USER_CLKS_CTL_SW_RST_VEC_0, 0);
	wmb(); /* order is important here */

	if (is_sparrow) {
		W(RGF_USER_CLKS_CTL_SW_RST_VEC_3, 0x00000003);
		/* reset A2 PCIE AHB */
		W(RGF_USER_CLKS_CTL_SW_RST_VEC_2, 0x00008000);

	} else {
		W(RGF_USER_CLKS_CTL_SW_RST_VEC_3, 0x00000001);
		if (rev_id == 1) {
			/* reset A1 BOTH PCIE AHB & PCIE RGF */
			W(RGF_USER_CLKS_CTL_SW_RST_VEC_2, 0x00000080);
		} else {
			W(RGF_PCIE_LOS_COUNTER_CTL, BIT(6) | BIT(8));
			W(RGF_USER_CLKS_CTL_SW_RST_VEC_2, 0x00008000);
		}

	}

	/* TODO: check order here!!! Erez code is different */
	W(RGF_USER_CLKS_CTL_SW_RST_VEC_0, 0);
	wmb(); /* order is important here */

	/* wait until device ready. typical time is 200..250 msec */
	do {
		msleep(RST_DELAY);
		hw_state = R(RGF_USER_HW_MACHINE_STATE);
		if (delay++ > RST_COUNT) {
			wil_err(wil, "Reset not completed, hw_state 0x%08x\n",
				hw_state);
			return -ETIME;
		}
	} while (hw_state != HW_MACHINE_BOOT_DONE);

	/* TODO: Erez check rev_id != 1 */
	if (!is_sparrow && (rev_id != 1))
		W(RGF_PCIE_LOS_COUNTER_CTL, BIT(8));

	C(RGF_USER_CLKS_CTL_0, BIT_USER_CLKS_RST_PWGD);
	wmb(); /* order is important here */

	wil_dbg_misc(wil, "Reset completed in %d ms\n", delay * RST_DELAY);
	return 0;

#undef R
#undef W
#undef S
#undef C
}

void wil_mbox_ring_le2cpus(struct wil6210_mbox_ring *r)
{
	le32_to_cpus(&r->base);
	le16_to_cpus(&r->entry_size);
	le16_to_cpus(&r->size);
	le32_to_cpus(&r->tail);
	le32_to_cpus(&r->head);
}

static int wil_wait_for_fw_ready(struct wil6210_priv *wil)
{
	ulong to = msecs_to_jiffies(1000);
	ulong left = wait_for_completion_timeout(&wil->wmi_ready, to);
	if (0 == left) {
		wil_err(wil, "Firmware not ready\n");
		return -ETIME;
	} else {
		wil_info(wil, "FW ready after %d ms. HW version 0x%08x\n",
			 jiffies_to_msecs(to-left), wil->hw_version);
	}
	return 0;
}

/*
 * We reset all the structures, and we reset the UMAC.
 * After calling this routine, you're expected to reload
 * the firmware.
 */
int wil_reset(struct wil6210_priv *wil)
{
	int rc;

	WARN_ON(!mutex_is_locked(&wil->mutex));

	cancel_work_sync(&wil->disconnect_worker);
	wil6210_disconnect(wil, NULL);

	wil->status = 0; /* prevent NAPI from being scheduled */
	if (test_bit(wil_status_napi_en, &wil->status)) {
		napi_synchronize(&wil->napi_rx);
	}

	if (wil->scan_request) {
		wil_dbg_misc(wil, "Abort scan_request 0x%p\n",
			     wil->scan_request);
		del_timer_sync(&wil->scan_timer);
		cfg80211_scan_done(wil->scan_request, true);
		wil->scan_request = NULL;
	}

	wil6210_disable_irq(wil);

	wmi_event_flush(wil);

	flush_workqueue(wil->wmi_wq_conn);
	flush_workqueue(wil->wmi_wq);

	rc = wil_target_reset(wil);
	wil_rx_fini(wil);
	if (rc)
		return rc;


	/* init after reset */
	wil->pending_connect_cid = -1;
	reinit_completion(&wil->wmi_ready);

	/* TODO: release MAC reset */
	wil6210_enable_irq(wil);

	/* we just started MAC, wait for FW ready */
	rc = wil_wait_for_fw_ready(wil);

	return rc;
}

void wil_fw_error_recovery(struct wil6210_priv *wil)
{
	wil_dbg_misc(wil, "starting fw error recovery\n");
	schedule_work(&wil->fw_error_worker);
}

void wil_link_on(struct wil6210_priv *wil)
{
	struct net_device *ndev = wil_to_ndev(wil);

	wil_dbg_misc(wil, "%s()\n", __func__);

	netif_carrier_on(ndev);
	wil_dbg_misc(wil, "netif_tx_wake : link on\n");
	netif_tx_wake_all_queues(ndev);
}

void wil_link_off(struct wil6210_priv *wil)
{
	struct net_device *ndev = wil_to_ndev(wil);

	wil_dbg_misc(wil, "%s()\n", __func__);

	netif_tx_stop_all_queues(ndev);
	wil_dbg_misc(wil, "netif_tx_stop : link off\n");
	netif_carrier_off(ndev);
}

static int __wil_up(struct wil6210_priv *wil)
{
	struct net_device *ndev = wil_to_ndev(wil);
	struct wireless_dev *wdev = wil->wdev;
	int rc;

	WARN_ON(!mutex_is_locked(&wil->mutex));

	rc = wil_reset(wil);
	if (rc)
		return rc;

	/* Rx VRING. After MAC and beacon */
	rc = wil_rx_init(wil);
	if (rc)
		return rc;

	switch (wdev->iftype) {
	case NL80211_IFTYPE_STATION:
		wil_dbg_misc(wil, "type: STATION\n");
		ndev->type = ARPHRD_ETHER;
		break;
	case NL80211_IFTYPE_AP:
		wil_dbg_misc(wil, "type: AP\n");
		ndev->type = ARPHRD_ETHER;
		break;
	case NL80211_IFTYPE_P2P_CLIENT:
		wil_dbg_misc(wil, "type: P2P_CLIENT\n");
		ndev->type = ARPHRD_ETHER;
		break;
	case NL80211_IFTYPE_P2P_GO:
		wil_dbg_misc(wil, "type: P2P_GO\n");
		ndev->type = ARPHRD_ETHER;
		break;
	case NL80211_IFTYPE_MONITOR:
		wil_dbg_misc(wil, "type: Monitor\n");
		ndev->type = ARPHRD_IEEE80211_RADIOTAP;
		/* ARPHRD_IEEE80211 or ARPHRD_IEEE80211_RADIOTAP ? */
		break;
	default:
		return -EOPNOTSUPP;
	}

	/* MAC address - pre-requisite for other commands */
	wmi_set_mac_address(wil, ndev->dev_addr);


	napi_enable(&wil->napi_rx);
	napi_enable(&wil->napi_tx);
	set_bit(wil_status_napi_en, &wil->status);

	return 0;
}

int wil_up(struct wil6210_priv *wil)
{
	int rc;

	mutex_lock(&wil->mutex);
	rc = __wil_up(wil);
	mutex_unlock(&wil->mutex);

	return rc;
}

static int __wil_down(struct wil6210_priv *wil)
{
	WARN_ON(!mutex_is_locked(&wil->mutex));

	clear_bit(wil_status_napi_en, &wil->status);
	napi_disable(&wil->napi_rx);
	napi_disable(&wil->napi_tx);

	if (wil->scan_request) {
		wil_dbg_misc(wil, "Abort scan_request 0x%p\n",
			     wil->scan_request);
		del_timer_sync(&wil->scan_timer);
		cfg80211_scan_done(wil->scan_request, true);
		wil->scan_request = NULL;
	}

	wil6210_disconnect(wil, NULL);
	wil_rx_fini(wil);

	return 0;
}

int wil_down(struct wil6210_priv *wil)
{
	int rc;

	mutex_lock(&wil->mutex);
	rc = __wil_down(wil);
	mutex_unlock(&wil->mutex);

	return rc;
}

int wil_find_cid(struct wil6210_priv *wil, const u8 *mac)
{
	int i;
	int rc = -ENOENT;

	for (i = 0; i < ARRAY_SIZE(wil->sta); i++) {
		if ((wil->sta[i].status != wil_sta_unused) &&
		    ether_addr_equal(wil->sta[i].addr, mac)) {
			rc = i;
			break;
		}
	}

	return rc;
}