1# 2# wan devices configuration 3# 4 5menuconfig WAN 6 bool "Wan interfaces support" 7 ---help--- 8 Wide Area Networks (WANs), such as X.25, Frame Relay and leased 9 lines, are used to interconnect Local Area Networks (LANs) over vast 10 distances with data transfer rates significantly higher than those 11 achievable with commonly used asynchronous modem connections. 12 13 Usually, a quite expensive external device called a `WAN router' is 14 needed to connect to a WAN. As an alternative, a relatively 15 inexpensive WAN interface card can allow your Linux box to directly 16 connect to a WAN. 17 18 If you have one of those cards and wish to use it under Linux, 19 say Y here and also to the WAN driver for your card. 20 21 If unsure, say N. 22 23if WAN 24 25# There is no way to detect a comtrol sv11 - force it modular for now. 26config HOSTESS_SV11 27 tristate "Comtrol Hostess SV-11 support" 28 depends on ISA && m && ISA_DMA_API && INET && HDLC && VIRT_TO_BUS 29 help 30 Driver for Comtrol Hostess SV-11 network card which 31 operates on low speed synchronous serial links at up to 32 256Kbps, supporting PPP and Cisco HDLC. 33 34 The driver will be compiled as a module: the 35 module will be called hostess_sv11. 36 37# The COSA/SRP driver has not been tested as non-modular yet. 38config COSA 39 tristate "COSA/SRP sync serial boards support" 40 depends on ISA && m && ISA_DMA_API && HDLC && VIRT_TO_BUS 41 ---help--- 42 Driver for COSA and SRP synchronous serial boards. 43 44 These boards allow to connect synchronous serial devices (for example 45 base-band modems, or any other device with the X.21, V.24, V.35 or 46 V.36 interface) to your Linux box. The cards can work as the 47 character device, synchronous PPP network device, or the Cisco HDLC 48 network device. 49 50 You will need user-space utilities COSA or SRP boards for downloading 51 the firmware to the cards and to set them up. Look at the 52 <http://www.fi.muni.cz/~kas/cosa/> for more information. You can also 53 read the comment at the top of the <file:drivers/net/wan/cosa.c> for 54 details about the cards and the driver itself. 55 56 The driver will be compiled as a module: the 57 module will be called cosa. 58 59# 60# Lan Media's board. Currently 1000, 1200, 5200, 5245 61# 62config LANMEDIA 63 tristate "LanMedia Corp. SSI/V.35, T1/E1, HSSI, T3 boards" 64 depends on PCI && VIRT_TO_BUS && HDLC 65 ---help--- 66 Driver for the following Lan Media family of serial boards: 67 68 - LMC 1000 board allows you to connect synchronous serial devices 69 (for example base-band modems, or any other device with the X.21, 70 V.24, V.35 or V.36 interface) to your Linux box. 71 72 - LMC 1200 with on board DSU board allows you to connect your Linux 73 box directly to a T1 or E1 circuit. 74 75 - LMC 5200 board provides a HSSI interface capable of running up to 76 52 Mbits per second. 77 78 - LMC 5245 board connects directly to a T3 circuit saving the 79 additional external hardware. 80 81 To change setting such as clock source you will need lmcctl. 82 It is available at <ftp://ftp.lanmedia.com/> (broken link). 83 84 To compile this driver as a module, choose M here: the 85 module will be called lmc. 86 87# There is no way to detect a Sealevel board. Force it modular 88config SEALEVEL_4021 89 tristate "Sealevel Systems 4021 support" 90 depends on ISA && m && ISA_DMA_API && INET && HDLC && VIRT_TO_BUS 91 help 92 This is a driver for the Sealevel Systems ACB 56 serial I/O adapter. 93 94 The driver will be compiled as a module: the 95 module will be called sealevel. 96 97# Generic HDLC 98config HDLC 99 tristate "Generic HDLC layer" 100 help 101 Say Y to this option if your Linux box contains a WAN (Wide Area 102 Network) card supported by this driver and you are planning to 103 connect the box to a WAN. 104 105 You will need supporting software from 106 <http://www.kernel.org/pub/linux/utils/net/hdlc/>. 107 Generic HDLC driver currently supports raw HDLC, Cisco HDLC, Frame 108 Relay, synchronous Point-to-Point Protocol (PPP) and X.25. 109 110 To compile this driver as a module, choose M here: the 111 module will be called hdlc. 112 113 If unsure, say N. 114 115config HDLC_RAW 116 tristate "Raw HDLC support" 117 depends on HDLC 118 help 119 Generic HDLC driver supporting raw HDLC over WAN connections. 120 121 If unsure, say N. 122 123config HDLC_RAW_ETH 124 tristate "Raw HDLC Ethernet device support" 125 depends on HDLC 126 help 127 Generic HDLC driver supporting raw HDLC Ethernet device emulation 128 over WAN connections. 129 130 You will need it for Ethernet over HDLC bridges. 131 132 If unsure, say N. 133 134config HDLC_CISCO 135 tristate "Cisco HDLC support" 136 depends on HDLC 137 help 138 Generic HDLC driver supporting Cisco HDLC over WAN connections. 139 140 If unsure, say N. 141 142config HDLC_FR 143 tristate "Frame Relay support" 144 depends on HDLC 145 help 146 Generic HDLC driver supporting Frame Relay over WAN connections. 147 148 If unsure, say N. 149 150config HDLC_PPP 151 tristate "Synchronous Point-to-Point Protocol (PPP) support" 152 depends on HDLC 153 help 154 Generic HDLC driver supporting PPP over WAN connections. 155 156 If unsure, say N. 157 158config HDLC_X25 159 tristate "X.25 protocol support" 160 depends on HDLC && (LAPB=m && HDLC=m || LAPB=y) 161 help 162 Generic HDLC driver supporting X.25 over WAN connections. 163 164 If unsure, say N. 165 166comment "X.25/LAPB support is disabled" 167 depends on HDLC && (LAPB!=m || HDLC!=m) && LAPB!=y 168 169config PCI200SYN 170 tristate "Goramo PCI200SYN support" 171 depends on HDLC && PCI 172 help 173 Driver for PCI200SYN cards by Goramo sp. j. 174 175 If you have such a card, say Y here and see 176 <http://www.kernel.org/pub/linux/utils/net/hdlc/>. 177 178 To compile this as a module, choose M here: the 179 module will be called pci200syn. 180 181 If unsure, say N. 182 183config WANXL 184 tristate "SBE Inc. wanXL support" 185 depends on HDLC && PCI 186 help 187 Driver for wanXL PCI cards by SBE Inc. 188 189 If you have such a card, say Y here and see 190 <http://www.kernel.org/pub/linux/utils/net/hdlc/>. 191 192 To compile this as a module, choose M here: the 193 module will be called wanxl. 194 195 If unsure, say N. 196 197config WANXL_BUILD_FIRMWARE 198 bool "rebuild wanXL firmware" 199 depends on WANXL && !PREVENT_FIRMWARE_BUILD 200 help 201 Allows you to rebuild firmware run by the QUICC processor. 202 It requires as68k, ld68k and hexdump programs. 203 204 You should never need this option, say N. 205 206config PC300TOO 207 tristate "Cyclades PC300 RSV/X21 alternative support" 208 depends on HDLC && PCI 209 help 210 Alternative driver for PC300 RSV/X21 PCI cards made by 211 Cyclades, Inc. If you have such a card, say Y here and see 212 <http://www.kernel.org/pub/linux/utils/net/hdlc/>. 213 214 To compile this as a module, choose M here: the module 215 will be called pc300too. 216 217 If unsure, say N here. 218 219config N2 220 tristate "SDL RISCom/N2 support" 221 depends on HDLC && ISA 222 help 223 Driver for RISCom/N2 single or dual channel ISA cards by 224 SDL Communications Inc. 225 226 If you have such a card, say Y here and see 227 <http://www.kernel.org/pub/linux/utils/net/hdlc/>. 228 229 Note that N2csu and N2dds cards are not supported by this driver. 230 231 To compile this driver as a module, choose M here: the module 232 will be called n2. 233 234 If unsure, say N. 235 236config C101 237 tristate "Moxa C101 support" 238 depends on HDLC && ISA 239 help 240 Driver for C101 SuperSync ISA cards by Moxa Technologies Co., Ltd. 241 242 If you have such a card, say Y here and see 243 <http://www.kernel.org/pub/linux/utils/net/hdlc/>. 244 245 To compile this driver as a module, choose M here: the 246 module will be called c101. 247 248 If unsure, say N. 249 250config FARSYNC 251 tristate "FarSync T-Series support" 252 depends on HDLC && PCI 253 ---help--- 254 Support for the FarSync T-Series X.21 (and V.35/V.24) cards by 255 FarSite Communications Ltd. 256 257 Synchronous communication is supported on all ports at speeds up to 258 8Mb/s (128K on V.24) using synchronous PPP, Cisco HDLC, raw HDLC, 259 Frame Relay or X.25/LAPB. 260 261 If you want the module to be automatically loaded when the interface 262 is referenced then you should add "alias hdlcX farsync" to a file 263 in /etc/modprobe.d/ for each interface, where X is 0, 1, 2, ..., or 264 simply use "alias hdlc* farsync" to indicate all of them. 265 266 To compile this driver as a module, choose M here: the 267 module will be called farsync. 268 269config DSCC4 270 tristate "Etinc PCISYNC serial board support" 271 depends on HDLC && PCI && m 272 help 273 Driver for Etinc PCISYNC boards based on the Infineon (ex. Siemens) 274 DSCC4 chipset. 275 276 This is supposed to work with the four port card. Take a look at 277 <http://www.cogenit.fr/dscc4/> for further information about the 278 driver. 279 280 To compile this driver as a module, choose M here: the 281 module will be called dscc4. 282 283config FSL_UCC_HDLC 284 tristate "Freescale QUICC Engine HDLC support" 285 depends on HDLC 286 depends on QUICC_ENGINE 287 help 288 Driver for Freescale QUICC Engine HDLC controller. The driver 289 supports HDLC in NMSI and TDM mode. 290 291 To compile this driver as a module, choose M here: the 292 module will be called fsl_ucc_hdlc. 293 294config SLIC_DS26522 295 tristate "Slic Maxim ds26522 card support" 296 depends on SPI 297 depends on FSL_SOC || ARCH_MXC || ARCH_LAYERSCAPE || COMPILE_TEST 298 help 299 This module initializes and configures the slic maxim card 300 in T1 or E1 mode. 301 302 To compile this driver as a module, choose M here: the 303 module will be called slic_ds26522. 304 305config DSCC4_PCISYNC 306 bool "Etinc PCISYNC features" 307 depends on DSCC4 308 help 309 Due to Etinc's design choice for its PCISYNC cards, some operations 310 are only allowed on specific ports of the DSCC4. This option is the 311 only way for the driver to know that it shouldn't return a success 312 code for these operations. 313 314 Please say Y if your card is an Etinc's PCISYNC. 315 316config DSCC4_PCI_RST 317 bool "Hard reset support" 318 depends on DSCC4 319 help 320 Various DSCC4 bugs forbid any reliable software reset of the ASIC. 321 As a replacement, some vendors provide a way to assert the PCI #RST 322 pin of DSCC4 through the GPIO port of the card. If you choose Y, 323 the driver will make use of this feature before module removal 324 (i.e. rmmod). The feature is known to be available on Commtech's 325 cards. Contact your manufacturer for details. 326 327 Say Y if your card supports this feature. 328 329config IXP4XX_HSS 330 tristate "Intel IXP4xx HSS (synchronous serial port) support" 331 depends on HDLC && ARM && ARCH_IXP4XX && IXP4XX_NPE && IXP4XX_QMGR 332 help 333 Say Y here if you want to use built-in HSS ports 334 on IXP4xx processor. 335 336config DLCI 337 tristate "Frame Relay DLCI support" 338 ---help--- 339 Support for the Frame Relay protocol. 340 341 Frame Relay is a fast low-cost way to connect to a remote Internet 342 access provider or to form a private wide area network. The one 343 physical line from your box to the local "switch" (i.e. the entry 344 point to the Frame Relay network, usually at the phone company) can 345 carry several logical point-to-point connections to other computers 346 connected to the Frame Relay network. For a general explanation of 347 the protocol, check out <http://www.mplsforum.org/>. 348 349 To use frame relay, you need supporting hardware (called FRAD) and 350 certain programs from the net-tools package as explained in 351 <file:Documentation/networking/framerelay.txt>. 352 353 To compile this driver as a module, choose M here: the 354 module will be called dlci. 355 356config DLCI_MAX 357 int "Max DLCI per device" 358 depends on DLCI 359 default "8" 360 help 361 How many logical point-to-point frame relay connections (the 362 identifiers of which are called DCLIs) should be handled by each 363 of your hardware frame relay access devices. 364 365 Go with the default. 366 367config SDLA 368 tristate "SDLA (Sangoma S502/S508) support" 369 depends on DLCI && ISA 370 help 371 Driver for the Sangoma S502A, S502E, and S508 Frame Relay Access 372 Devices. 373 374 These are multi-protocol cards, but only Frame Relay is supported 375 by the driver at this time. Please read 376 <file:Documentation/networking/framerelay.txt>. 377 378 To compile this driver as a module, choose M here: the 379 module will be called sdla. 380 381# X.25 network drivers 382config LAPBETHER 383 tristate "LAPB over Ethernet driver" 384 depends on LAPB && X25 385 ---help--- 386 Driver for a pseudo device (typically called /dev/lapb0) which allows 387 you to open an LAPB point-to-point connection to some other computer 388 on your Ethernet network. 389 390 In order to do this, you need to say Y or M to the driver for your 391 Ethernet card as well as to "LAPB Data Link Driver". 392 393 To compile this driver as a module, choose M here: the 394 module will be called lapbether. 395 396 If unsure, say N. 397 398config X25_ASY 399 tristate "X.25 async driver" 400 depends on LAPB && X25 && TTY 401 ---help--- 402 Send and receive X.25 frames over regular asynchronous serial 403 lines such as telephone lines equipped with ordinary modems. 404 405 Experts should note that this driver doesn't currently comply with 406 the asynchronous HDLS framing protocols in CCITT recommendation X.25. 407 408 To compile this driver as a module, choose M here: the 409 module will be called x25_asy. 410 411 If unsure, say N. 412 413config SBNI 414 tristate "Granch SBNI12 Leased Line adapter support" 415 depends on X86 416 ---help--- 417 Driver for ISA SBNI12-xx cards which are low cost alternatives to 418 leased line modems. 419 420 You can find more information and last versions of drivers and 421 utilities at <http://www.granch.ru/>. If you have any question you 422 can send email to <sbni@granch.ru>. 423 424 To compile this driver as a module, choose M here: the 425 module will be called sbni. 426 427 If unsure, say N. 428 429config SBNI_MULTILINE 430 bool "Multiple line feature support" 431 depends on SBNI 432 help 433 Schedule traffic for some parallel lines, via SBNI12 adapters. 434 435 If you have two computers connected with two parallel lines it's 436 possible to increase transfer rate nearly twice. You should have 437 a program named 'sbniconfig' to configure adapters. 438 439 If unsure, say N. 440 441endif # WAN 442