1# 2# USB Network devices configuration 3# 4comment "Networking support is needed for USB Network Adapter support" 5 depends on USB && !NET 6 7menu "USB Network Adapters" 8 depends on USB && NET 9 10config USB_CATC 11 tristate "USB CATC NetMate-based Ethernet device support (EXPERIMENTAL)" 12 depends on EXPERIMENTAL 13 select CRC32 14 ---help--- 15 Say Y if you want to use one of the following 10Mbps USB Ethernet 16 device based on the EL1210A chip. Supported devices are: 17 Belkin F5U011 18 Belkin F5U111 19 CATC NetMate 20 CATC NetMate II 21 smartBridges smartNIC 22 23 This driver makes the adapter appear as a normal Ethernet interface, 24 typically on eth0, if it is the only ethernet device, or perhaps on 25 eth1, if you have a PCI or ISA ethernet card installed. 26 27 To compile this driver as a module, choose M here: the 28 module will be called catc. 29 30config USB_KAWETH 31 tristate "USB KLSI KL5USB101-based ethernet device support" 32 ---help--- 33 Say Y here if you want to use one of the following 10Mbps only 34 USB Ethernet adapters based on the KLSI KL5KUSB101B chipset: 35 3Com 3C19250 36 ADS USB-10BT 37 ATEN USB Ethernet 38 ASANTE USB To Ethernet Adapter 39 AOX Endpoints USB Ethernet 40 Correga K.K. 41 D-Link DSB-650C and DU-E10 42 Entrega / Portgear E45 43 I-O DATA USB-ET/T 44 Jaton USB Ethernet Device Adapter 45 Kingston Technology USB Ethernet Adapter 46 Linksys USB10T 47 Mobility USB-Ethernet Adapter 48 NetGear EA-101 49 Peracom Enet and Enet2 50 Portsmith Express Ethernet Adapter 51 Shark Pocket Adapter 52 SMC 2202USB 53 Sony Vaio port extender 54 55 This driver is likely to work with most 10Mbps only USB Ethernet 56 adapters, including some "no brand" devices. It does NOT work on 57 SmartBridges smartNIC or on Belkin F5U111 devices - you should use 58 the CATC NetMate driver for those. If you are not sure which one 59 you need, select both, and the correct one should be selected for 60 you. 61 62 This driver makes the adapter appear as a normal Ethernet interface, 63 typically on eth0, if it is the only ethernet device, or perhaps on 64 eth1, if you have a PCI or ISA ethernet card installed. 65 66 To compile this driver as a module, choose M here: the 67 module will be called kaweth. 68 69config USB_PEGASUS 70 tristate "USB Pegasus/Pegasus-II based ethernet device support" 71 select MII 72 ---help--- 73 Say Y here if you know you have Pegasus or Pegasus-II based adapter. 74 If in doubt then look at <file:drivers/net/usb/pegasus.h> for the 75 complete list of supported devices. 76 77 If your particular adapter is not in the list and you are _sure_ it 78 is Pegasus or Pegasus II based then send me 79 <petkan@users.sourceforge.net> vendor and device IDs. 80 81 To compile this driver as a module, choose M here: the 82 module will be called pegasus. 83 84config USB_RTL8150 85 tristate "USB RTL8150 based ethernet device support (EXPERIMENTAL)" 86 depends on EXPERIMENTAL 87 select MII 88 help 89 Say Y here if you have RTL8150 based usb-ethernet adapter. 90 Send me <petkan@users.sourceforge.net> any comments you may have. 91 You can also check for updates at <http://pegasus2.sourceforge.net/>. 92 93 To compile this driver as a module, choose M here: the 94 module will be called rtl8150. 95 96config USB_USBNET 97 tristate "Multi-purpose USB Networking Framework" 98 select MII 99 ---help--- 100 This driver supports several kinds of network links over USB, 101 with "minidrivers" built around a common network driver core 102 that supports deep queues for efficient transfers. (This gives 103 better performance with small packets and at high speeds). 104 105 The USB host runs "usbnet", and the other end of the link might be: 106 107 - Another USB host, when using USB "network" or "data transfer" 108 cables. These are often used to network laptops to PCs, like 109 "Laplink" parallel cables or some motherboards. These rely 110 on specialized chips from many suppliers. 111 112 - An intelligent USB gadget, perhaps embedding a Linux system. 113 These include PDAs running Linux (iPaq, Yopy, Zaurus, and 114 others), and devices that interoperate using the standard 115 CDC-Ethernet specification (including many cable modems). 116 117 - Network adapter hardware (like those for 10/100 Ethernet) which 118 uses this driver framework. 119 120 The link will appear with a name like "usb0", when the link is 121 a two-node link, or "eth0" for most CDC-Ethernet devices. Those 122 two-node links are most easily managed with Ethernet Bridging 123 (CONFIG_BRIDGE) instead of routing. 124 125 For more information see <http://www.linux-usb.org/usbnet/>. 126 127 To compile this driver as a module, choose M here: the 128 module will be called usbnet. 129 130config USB_NET_AX8817X 131 tristate "ASIX AX88xxx Based USB 2.0 Ethernet Adapters" 132 depends on USB_USBNET 133 select CRC32 134 default y 135 help 136 This option adds support for ASIX AX88xxx based USB 2.0 137 10/100 Ethernet adapters. 138 139 This driver should work with at least the following devices: 140 * Aten UC210T 141 * ASIX AX88172 142 * Billionton Systems, USB2AR 143 * Buffalo LUA-U2-KTX 144 * Corega FEther USB2-TX 145 * D-Link DUB-E100 146 * Hawking UF200 147 * Linksys USB200M 148 * Netgear FA120 149 * Sitecom LN-029 150 * Intellinet USB 2.0 Ethernet 151 * ST Lab USB 2.0 Ethernet 152 * TrendNet TU2-ET100 153 154 This driver creates an interface named "ethX", where X depends on 155 what other networking devices you have in use. 156 157config USB_HSO 158 tristate "Option USB High Speed Mobile Devices" 159 depends on USB && RFKILL 160 default n 161 help 162 Choose this option if you have an Option HSDPA/HSUPA card. 163 These cards support downlink speeds of 7.2Mbps or greater. 164 165 To compile this driver as a module, choose M here: the 166 module will be called hso. 167 168config USB_NET_CDCETHER 169 tristate "CDC Ethernet support (smart devices such as cable modems)" 170 depends on USB_USBNET 171 default y 172 help 173 This option supports devices conforming to the Communication Device 174 Class (CDC) Ethernet Control Model, a specification that's easy to 175 implement in device firmware. The CDC specifications are available 176 from <http://www.usb.org/>. 177 178 CDC Ethernet is an implementation option for DOCSIS cable modems 179 that support USB connectivity, used for non-Microsoft USB hosts. 180 The Linux-USB CDC Ethernet Gadget driver is an open implementation. 181 This driver should work with at least the following devices: 182 183 * Ericsson PipeRider (all variants) 184 * Motorola (DM100 and SB4100) 185 * Broadcom Cable Modem (reference design) 186 * Toshiba PCX1100U 187 * ... 188 189 This driver creates an interface named "ethX", where X depends on 190 what other networking devices you have in use. However, if the 191 IEEE 802 "local assignment" bit is set in the address, a "usbX" 192 name is used instead. 193 194config USB_NET_DM9601 195 tristate "Davicom DM9601 based USB 1.1 10/100 ethernet devices" 196 depends on USB_USBNET 197 select CRC32 198 help 199 This option adds support for Davicom DM9601 based USB 1.1 200 10/100 Ethernet adapters. 201 202config USB_NET_GL620A 203 tristate "GeneSys GL620USB-A based cables" 204 depends on USB_USBNET 205 help 206 Choose this option if you're using a host-to-host cable, 207 or PC2PC motherboard, with this chip. 208 209 Note that the half-duplex "GL620USB" is not supported. 210 211config USB_NET_NET1080 212 tristate "NetChip 1080 based cables (Laplink, ...)" 213 default y 214 depends on USB_USBNET 215 help 216 Choose this option if you're using a host-to-host cable based 217 on this design: one NetChip 1080 chip and supporting logic, 218 optionally with LEDs that indicate traffic 219 220config USB_NET_PLUSB 221 tristate "Prolific PL-2301/2302 based cables" 222 # if the handshake/init/reset problems, from original 'plusb', 223 # are ever resolved ... then remove "experimental" 224 depends on USB_USBNET && EXPERIMENTAL 225 help 226 Choose this option if you're using a host-to-host cable 227 with one of these chips. 228 229config USB_NET_MCS7830 230 tristate "MosChip MCS7830 based Ethernet adapters" 231 depends on USB_USBNET 232 help 233 Choose this option if you're using a 10/100 Ethernet USB2 234 adapter based on the MosChip 7830 controller. This includes 235 adapters marketed under the DeLOCK brand. 236 237config USB_NET_RNDIS_HOST 238 tristate "Host for RNDIS and ActiveSync devices (EXPERIMENTAL)" 239 depends on USB_USBNET && EXPERIMENTAL 240 select USB_NET_CDCETHER 241 help 242 This option enables hosting "Remote NDIS" USB networking links, 243 as encouraged by Microsoft (instead of CDC Ethernet!) for use in 244 various devices that may only support this protocol. A variant 245 of this protocol (with even less public documentation) seems to 246 be at the root of Microsoft's "ActiveSync" too. 247 248 Avoid using this protocol unless you have no better options. 249 The protocol specification is incomplete, and is controlled by 250 (and for) Microsoft; it isn't an "Open" ecosystem or market. 251 252config USB_NET_CDC_SUBSET 253 tristate "Simple USB Network Links (CDC Ethernet subset)" 254 depends on USB_USBNET 255 default y 256 help 257 This driver module supports USB network devices that can work 258 without any device-specific information. Select it if you have 259 one of these drivers. 260 261 Note that while many USB host-to-host cables can work in this mode, 262 that may mean not being able to talk to Win32 systems or more 263 commonly not being able to handle certain events (like replugging 264 the host on the other end) very well. Also, these devices will 265 not generally have permanently assigned Ethernet addresses. 266 267config USB_ALI_M5632 268 boolean "ALi M5632 based 'USB 2.0 Data Link' cables" 269 depends on USB_NET_CDC_SUBSET 270 help 271 Choose this option if you're using a host-to-host cable 272 based on this design, which supports USB 2.0 high speed. 273 274config USB_AN2720 275 boolean "AnchorChips 2720 based cables (Xircom PGUNET, ...)" 276 depends on USB_NET_CDC_SUBSET 277 help 278 Choose this option if you're using a host-to-host cable 279 based on this design. Note that AnchorChips is now a 280 Cypress brand. 281 282config USB_BELKIN 283 boolean "eTEK based host-to-host cables (Advance, Belkin, ...)" 284 depends on USB_NET_CDC_SUBSET 285 default y 286 help 287 Choose this option if you're using a host-to-host cable 288 based on this design: two NetChip 2890 chips and an Atmel 289 microcontroller, with LEDs that indicate traffic. 290 291config USB_ARMLINUX 292 boolean "Embedded ARM Linux links (iPaq, ...)" 293 depends on USB_NET_CDC_SUBSET 294 default y 295 help 296 Choose this option to support the "usb-eth" networking driver 297 used by most of the ARM Linux community with device controllers 298 such as the SA-11x0 and PXA-25x UDCs, or the tftp capabilities 299 in some PXA versions of the "blob" boot loader. 300 301 Linux-based "Gumstix" PXA-25x based systems use this protocol 302 to talk with other Linux systems. 303 304 Although the ROMs shipped with Sharp Zaurus products use a 305 different link level framing protocol, you can have them use 306 this simpler protocol by installing a different kernel. 307 308config USB_EPSON2888 309 boolean "Epson 2888 based firmware (DEVELOPMENT)" 310 depends on USB_NET_CDC_SUBSET 311 help 312 Choose this option to support the usb networking links used 313 by some sample firmware from Epson. 314 315config USB_KC2190 316 boolean "KT Technology KC2190 based cables (InstaNet)" 317 depends on USB_NET_CDC_SUBSET && EXPERIMENTAL 318 help 319 Choose this option if you're using a host-to-host cable 320 with one of these chips. 321 322config USB_NET_ZAURUS 323 tristate "Sharp Zaurus (stock ROMs) and compatible" 324 depends on USB_USBNET 325 select USB_NET_CDCETHER 326 select CRC32 327 default y 328 help 329 Choose this option to support the usb networking links used by 330 Zaurus models like the SL-5000D, SL-5500, SL-5600, A-300, B-500. 331 This also supports some related device firmware, as used in some 332 PDAs from Olympus and some cell phones from Motorola. 333 334 If you install an alternate image, such as the Linux 2.6 based 335 versions of OpenZaurus, you should no longer need to support this 336 protocol. Only the "eth-fd" or "net_fd" drivers in these devices 337 really need this non-conformant variant of CDC Ethernet (or in 338 some cases CDC MDLM) protocol, not "g_ether". 339 340 341endmenu 342