1# 2# USB Network devices configuration 3# 4comment "Networking support is needed for USB Network Adapter support" 5 depends on USB && !NET 6 7menu "USB Network Adapters" 8 depends on USB && NET 9 10config USB_CATC 11 tristate "USB CATC NetMate-based Ethernet device support (EXPERIMENTAL)" 12 depends on EXPERIMENTAL 13 select CRC32 14 ---help--- 15 Say Y if you want to use one of the following 10Mbps USB Ethernet 16 device based on the EL1210A chip. Supported devices are: 17 Belkin F5U011 18 Belkin F5U111 19 CATC NetMate 20 CATC NetMate II 21 smartBridges smartNIC 22 23 This driver makes the adapter appear as a normal Ethernet interface, 24 typically on eth0, if it is the only ethernet device, or perhaps on 25 eth1, if you have a PCI or ISA ethernet card installed. 26 27 To compile this driver as a module, choose M here: the 28 module will be called catc. 29 30config USB_KAWETH 31 tristate "USB KLSI KL5USB101-based ethernet device support" 32 ---help--- 33 Say Y here if you want to use one of the following 10Mbps only 34 USB Ethernet adapters based on the KLSI KL5KUSB101B chipset: 35 3Com 3C19250 36 ADS USB-10BT 37 ATEN USB Ethernet 38 ASANTE USB To Ethernet Adapter 39 AOX Endpoints USB Ethernet 40 Correga K.K. 41 D-Link DSB-650C and DU-E10 42 Entrega / Portgear E45 43 I-O DATA USB-ET/T 44 Jaton USB Ethernet Device Adapter 45 Kingston Technology USB Ethernet Adapter 46 Linksys USB10T 47 Mobility USB-Ethernet Adapter 48 NetGear EA-101 49 Peracom Enet and Enet2 50 Portsmith Express Ethernet Adapter 51 Shark Pocket Adapter 52 SMC 2202USB 53 Sony Vaio port extender 54 55 This driver is likely to work with most 10Mbps only USB Ethernet 56 adapters, including some "no brand" devices. It does NOT work on 57 SmartBridges smartNIC or on Belkin F5U111 devices - you should use 58 the CATC NetMate driver for those. If you are not sure which one 59 you need, select both, and the correct one should be selected for 60 you. 61 62 This driver makes the adapter appear as a normal Ethernet interface, 63 typically on eth0, if it is the only ethernet device, or perhaps on 64 eth1, if you have a PCI or ISA ethernet card installed. 65 66 To compile this driver as a module, choose M here: the 67 module will be called kaweth. 68 69config USB_PEGASUS 70 tristate "USB Pegasus/Pegasus-II based ethernet device support" 71 select MII 72 ---help--- 73 Say Y here if you know you have Pegasus or Pegasus-II based adapter. 74 If in doubt then look at <file:drivers/usb/net/pegasus.h> for the 75 complete list of supported devices. 76 77 If your particular adapter is not in the list and you are _sure_ it 78 is Pegasus or Pegasus II based then send me 79 <petkan@users.sourceforge.net> vendor and device IDs. 80 81 To compile this driver as a module, choose M here: the 82 module will be called pegasus. 83 84config USB_RTL8150 85 tristate "USB RTL8150 based ethernet device support (EXPERIMENTAL)" 86 depends on EXPERIMENTAL 87 select MII 88 help 89 Say Y here if you have RTL8150 based usb-ethernet adapter. 90 Send me <petkan@users.sourceforge.net> any comments you may have. 91 You can also check for updates at <http://pegasus2.sourceforge.net/>. 92 93 To compile this driver as a module, choose M here: the 94 module will be called rtl8150. 95 96config USB_USBNET_MII 97 tristate 98 default n 99 100config USB_USBNET 101 tristate "Multi-purpose USB Networking Framework" 102 select MII if USB_USBNET_MII != n 103 ---help--- 104 This driver supports several kinds of network links over USB, 105 with "minidrivers" built around a common network driver core 106 that supports deep queues for efficient transfers. (This gives 107 better performance with small packets and at high speeds). 108 109 The USB host runs "usbnet", and the other end of the link might be: 110 111 - Another USB host, when using USB "network" or "data transfer" 112 cables. These are often used to network laptops to PCs, like 113 "Laplink" parallel cables or some motherboards. These rely 114 on specialized chips from many suppliers. 115 116 - An intelligent USB gadget, perhaps embedding a Linux system. 117 These include PDAs running Linux (iPaq, Yopy, Zaurus, and 118 others), and devices that interoperate using the standard 119 CDC-Ethernet specification (including many cable modems). 120 121 - Network adapter hardware (like those for 10/100 Ethernet) which 122 uses this driver framework. 123 124 The link will appear with a name like "usb0", when the link is 125 a two-node link, or "eth0" for most CDC-Ethernet devices. Those 126 two-node links are most easily managed with Ethernet Bridging 127 (CONFIG_BRIDGE) instead of routing. 128 129 For more information see <http://www.linux-usb.org/usbnet/>. 130 131 To compile this driver as a module, choose M here: the 132 module will be called usbnet. 133 134config USB_NET_AX8817X 135 tristate "ASIX AX88xxx Based USB 2.0 Ethernet Adapters" 136 depends on USB_USBNET && NET_ETHERNET 137 select CRC32 138 select USB_USBNET_MII 139 default y 140 help 141 This option adds support for ASIX AX88xxx based USB 2.0 142 10/100 Ethernet adapters. 143 144 This driver should work with at least the following devices: 145 * Aten UC210T 146 * ASIX AX88172 147 * Billionton Systems, USB2AR 148 * Buffalo LUA-U2-KTX 149 * Corega FEther USB2-TX 150 * D-Link DUB-E100 151 * Hawking UF200 152 * Linksys USB200M 153 * Netgear FA120 154 * Sitecom LN-029 155 * Intellinet USB 2.0 Ethernet 156 * ST Lab USB 2.0 Ethernet 157 * TrendNet TU2-ET100 158 159 This driver creates an interface named "ethX", where X depends on 160 what other networking devices you have in use. 161 162 163config USB_NET_CDCETHER 164 tristate "CDC Ethernet support (smart devices such as cable modems)" 165 depends on USB_USBNET 166 default y 167 help 168 This option supports devices conforming to the Communication Device 169 Class (CDC) Ethernet Control Model, a specification that's easy to 170 implement in device firmware. The CDC specifications are available 171 from <http://www.usb.org/>. 172 173 CDC Ethernet is an implementation option for DOCSIS cable modems 174 that support USB connectivity, used for non-Microsoft USB hosts. 175 The Linux-USB CDC Ethernet Gadget driver is an open implementation. 176 This driver should work with at least the following devices: 177 178 * Ericsson PipeRider (all variants) 179 * Motorola (DM100 and SB4100) 180 * Broadcom Cable Modem (reference design) 181 * Toshiba PCX1100U 182 * ... 183 184 This driver creates an interface named "ethX", where X depends on 185 what other networking devices you have in use. However, if the 186 IEEE 802 "local assignment" bit is set in the address, a "usbX" 187 name is used instead. 188 189config USB_NET_DM9601 190 tristate "Davicom DM9601 based USB 1.1 10/100 ethernet devices" 191 depends on USB_USBNET 192 select CRC32 193 select USB_USBNET_MII 194 help 195 This option adds support for Davicom DM9601 based USB 1.1 196 10/100 Ethernet adapters. 197 198config USB_NET_GL620A 199 tristate "GeneSys GL620USB-A based cables" 200 depends on USB_USBNET 201 help 202 Choose this option if you're using a host-to-host cable, 203 or PC2PC motherboard, with this chip. 204 205 Note that the half-duplex "GL620USB" is not supported. 206 207config USB_NET_NET1080 208 tristate "NetChip 1080 based cables (Laplink, ...)" 209 default y 210 depends on USB_USBNET 211 help 212 Choose this option if you're using a host-to-host cable based 213 on this design: one NetChip 1080 chip and supporting logic, 214 optionally with LEDs that indicate traffic 215 216config USB_NET_PLUSB 217 tristate "Prolific PL-2301/2302 based cables" 218 # if the handshake/init/reset problems, from original 'plusb', 219 # are ever resolved ... then remove "experimental" 220 depends on USB_USBNET && EXPERIMENTAL 221 help 222 Choose this option if you're using a host-to-host cable 223 with one of these chips. 224 225config USB_NET_MCS7830 226 tristate "MosChip MCS7830 based Ethernet adapters" 227 depends on USB_USBNET 228 select USB_USBNET_MII 229 help 230 Choose this option if you're using a 10/100 Ethernet USB2 231 adapter based on the MosChip 7830 controller. This includes 232 adapters marketed under the DeLOCK brand. 233 234config USB_NET_RNDIS_HOST 235 tristate "Host for RNDIS and ActiveSync devices (EXPERIMENTAL)" 236 depends on USB_USBNET && EXPERIMENTAL 237 select USB_NET_CDCETHER 238 help 239 This option enables hosting "Remote NDIS" USB networking links, 240 as encouraged by Microsoft (instead of CDC Ethernet!) for use in 241 various devices that may only support this protocol. A variant 242 of this protocol (with even less public documentation) seems to 243 be at the root of Microsoft's "ActiveSync" too. 244 245 Avoid using this protocol unless you have no better options. 246 The protocol specification is incomplete, and is controlled by 247 (and for) Microsoft; it isn't an "Open" ecosystem or market. 248 249config USB_NET_CDC_SUBSET 250 tristate "Simple USB Network Links (CDC Ethernet subset)" 251 depends on USB_USBNET 252 default y 253 help 254 This driver module supports USB network devices that can work 255 without any device-specific information. Select it if you have 256 one of these drivers. 257 258 Note that while many USB host-to-host cables can work in this mode, 259 that may mean not being able to talk to Win32 systems or more 260 commonly not being able to handle certain events (like replugging 261 the host on the other end) very well. Also, these devices will 262 not generally have permanently assigned Ethernet addresses. 263 264config USB_ALI_M5632 265 boolean "ALi M5632 based 'USB 2.0 Data Link' cables" 266 depends on USB_NET_CDC_SUBSET 267 help 268 Choose this option if you're using a host-to-host cable 269 based on this design, which supports USB 2.0 high speed. 270 271config USB_AN2720 272 boolean "AnchorChips 2720 based cables (Xircom PGUNET, ...)" 273 depends on USB_NET_CDC_SUBSET 274 help 275 Choose this option if you're using a host-to-host cable 276 based on this design. Note that AnchorChips is now a 277 Cypress brand. 278 279config USB_BELKIN 280 boolean "eTEK based host-to-host cables (Advance, Belkin, ...)" 281 depends on USB_NET_CDC_SUBSET 282 default y 283 help 284 Choose this option if you're using a host-to-host cable 285 based on this design: two NetChip 2890 chips and an Atmel 286 microcontroller, with LEDs that indicate traffic. 287 288config USB_ARMLINUX 289 boolean "Embedded ARM Linux links (iPaq, ...)" 290 depends on USB_NET_CDC_SUBSET 291 default y 292 help 293 Choose this option to support the "usb-eth" networking driver 294 used by most of the ARM Linux community with device controllers 295 such as the SA-11x0 and PXA-25x UDCs, or the tftp capabilities 296 in some PXA versions of the "blob" boot loader. 297 298 Linux-based "Gumstix" PXA-25x based systems use this protocol 299 to talk with other Linux systems. 300 301 Although the ROMs shipped with Sharp Zaurus products use a 302 different link level framing protocol, you can have them use 303 this simpler protocol by installing a different kernel. 304 305config USB_EPSON2888 306 boolean "Epson 2888 based firmware (DEVELOPMENT)" 307 depends on USB_NET_CDC_SUBSET 308 help 309 Choose this option to support the usb networking links used 310 by some sample firmware from Epson. 311 312config USB_KC2190 313 boolean "KT Technology KC2190 based cables (InstaNet)" 314 depends on USB_NET_CDC_SUBSET && EXPERIMENTAL 315 help 316 Choose this option if you're using a host-to-host cable 317 with one of these chips. 318 319config USB_NET_ZAURUS 320 tristate "Sharp Zaurus (stock ROMs) and compatible" 321 depends on USB_USBNET 322 select USB_NET_CDCETHER 323 select CRC32 324 default y 325 help 326 Choose this option to support the usb networking links used by 327 Zaurus models like the SL-5000D, SL-5500, SL-5600, A-300, B-500. 328 This also supports some related device firmware, as used in some 329 PDAs from Olympus and some cell phones from Motorola. 330 331 If you install an alternate image, such as the Linux 2.6 based 332 versions of OpenZaurus, you should no longer need to support this 333 protocol. Only the "eth-fd" or "net_fd" drivers in these devices 334 really need this non-conformant variant of CDC Ethernet (or in 335 some cases CDC MDLM) protocol, not "g_ether". 336 337 338endmenu 339