1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Marvell 10G 88x3310 PHY driver 4 * 5 * Based upon the ID registers, this PHY appears to be a mixture of IPs 6 * from two different companies. 7 * 8 * There appears to be several different data paths through the PHY which 9 * are automatically managed by the PHY. The following has been determined 10 * via observation and experimentation for a setup using single-lane Serdes: 11 * 12 * SGMII PHYXS -- BASE-T PCS -- 10G PMA -- AN -- Copper (for <= 1G) 13 * 10GBASE-KR PHYXS -- BASE-T PCS -- 10G PMA -- AN -- Copper (for 10G) 14 * 10GBASE-KR PHYXS -- BASE-R PCS -- Fiber 15 * 16 * With XAUI, observation shows: 17 * 18 * XAUI PHYXS -- <appropriate PCS as above> 19 * 20 * and no switching of the host interface mode occurs. 21 * 22 * If both the fiber and copper ports are connected, the first to gain 23 * link takes priority and the other port is completely locked out. 24 */ 25 #include <linux/ctype.h> 26 #include <linux/delay.h> 27 #include <linux/hwmon.h> 28 #include <linux/marvell_phy.h> 29 #include <linux/phy.h> 30 #include <linux/sfp.h> 31 32 #define MV_PHY_ALASKA_NBT_QUIRK_MASK 0xfffffffe 33 #define MV_PHY_ALASKA_NBT_QUIRK_REV (MARVELL_PHY_ID_88X3310 | 0xa) 34 35 enum { 36 MV_PMA_FW_VER0 = 0xc011, 37 MV_PMA_FW_VER1 = 0xc012, 38 MV_PMA_BOOT = 0xc050, 39 MV_PMA_BOOT_FATAL = BIT(0), 40 41 MV_PCS_BASE_T = 0x0000, 42 MV_PCS_BASE_R = 0x1000, 43 MV_PCS_1000BASEX = 0x2000, 44 45 MV_PCS_CSCR1 = 0x8000, 46 MV_PCS_CSCR1_ED_MASK = 0x0300, 47 MV_PCS_CSCR1_ED_OFF = 0x0000, 48 MV_PCS_CSCR1_ED_RX = 0x0200, 49 MV_PCS_CSCR1_ED_NLP = 0x0300, 50 MV_PCS_CSCR1_MDIX_MASK = 0x0060, 51 MV_PCS_CSCR1_MDIX_MDI = 0x0000, 52 MV_PCS_CSCR1_MDIX_MDIX = 0x0020, 53 MV_PCS_CSCR1_MDIX_AUTO = 0x0060, 54 55 MV_PCS_CSSR1 = 0x8008, 56 MV_PCS_CSSR1_SPD1_MASK = 0xc000, 57 MV_PCS_CSSR1_SPD1_SPD2 = 0xc000, 58 MV_PCS_CSSR1_SPD1_1000 = 0x8000, 59 MV_PCS_CSSR1_SPD1_100 = 0x4000, 60 MV_PCS_CSSR1_SPD1_10 = 0x0000, 61 MV_PCS_CSSR1_DUPLEX_FULL= BIT(13), 62 MV_PCS_CSSR1_RESOLVED = BIT(11), 63 MV_PCS_CSSR1_MDIX = BIT(6), 64 MV_PCS_CSSR1_SPD2_MASK = 0x000c, 65 MV_PCS_CSSR1_SPD2_5000 = 0x0008, 66 MV_PCS_CSSR1_SPD2_2500 = 0x0004, 67 MV_PCS_CSSR1_SPD2_10000 = 0x0000, 68 69 /* Temperature read register (88E2110 only) */ 70 MV_PCS_TEMP = 0x8042, 71 72 /* These registers appear at 0x800X and 0xa00X - the 0xa00X control 73 * registers appear to set themselves to the 0x800X when AN is 74 * restarted, but status registers appear readable from either. 75 */ 76 MV_AN_CTRL1000 = 0x8000, /* 1000base-T control register */ 77 MV_AN_STAT1000 = 0x8001, /* 1000base-T status register */ 78 79 /* Vendor2 MMD registers */ 80 MV_V2_PORT_CTRL = 0xf001, 81 MV_V2_PORT_CTRL_SWRST = BIT(15), 82 MV_V2_PORT_CTRL_PWRDOWN = BIT(11), 83 MV_V2_PORT_MAC_TYPE_MASK = 0x7, 84 MV_V2_PORT_MAC_TYPE_RATE_MATCH = 0x6, 85 /* Temperature control/read registers (88X3310 only) */ 86 MV_V2_TEMP_CTRL = 0xf08a, 87 MV_V2_TEMP_CTRL_MASK = 0xc000, 88 MV_V2_TEMP_CTRL_SAMPLE = 0x0000, 89 MV_V2_TEMP_CTRL_DISABLE = 0xc000, 90 MV_V2_TEMP = 0xf08c, 91 MV_V2_TEMP_UNKNOWN = 0x9600, /* unknown function */ 92 }; 93 94 struct mv3310_priv { 95 u32 firmware_ver; 96 bool rate_match; 97 98 struct device *hwmon_dev; 99 char *hwmon_name; 100 }; 101 102 #ifdef CONFIG_HWMON 103 static umode_t mv3310_hwmon_is_visible(const void *data, 104 enum hwmon_sensor_types type, 105 u32 attr, int channel) 106 { 107 if (type == hwmon_chip && attr == hwmon_chip_update_interval) 108 return 0444; 109 if (type == hwmon_temp && attr == hwmon_temp_input) 110 return 0444; 111 return 0; 112 } 113 114 static int mv3310_hwmon_read_temp_reg(struct phy_device *phydev) 115 { 116 return phy_read_mmd(phydev, MDIO_MMD_VEND2, MV_V2_TEMP); 117 } 118 119 static int mv2110_hwmon_read_temp_reg(struct phy_device *phydev) 120 { 121 return phy_read_mmd(phydev, MDIO_MMD_PCS, MV_PCS_TEMP); 122 } 123 124 static int mv10g_hwmon_read_temp_reg(struct phy_device *phydev) 125 { 126 if (phydev->drv->phy_id == MARVELL_PHY_ID_88X3310) 127 return mv3310_hwmon_read_temp_reg(phydev); 128 else /* MARVELL_PHY_ID_88E2110 */ 129 return mv2110_hwmon_read_temp_reg(phydev); 130 } 131 132 static int mv3310_hwmon_read(struct device *dev, enum hwmon_sensor_types type, 133 u32 attr, int channel, long *value) 134 { 135 struct phy_device *phydev = dev_get_drvdata(dev); 136 int temp; 137 138 if (type == hwmon_chip && attr == hwmon_chip_update_interval) { 139 *value = MSEC_PER_SEC; 140 return 0; 141 } 142 143 if (type == hwmon_temp && attr == hwmon_temp_input) { 144 temp = mv10g_hwmon_read_temp_reg(phydev); 145 if (temp < 0) 146 return temp; 147 148 *value = ((temp & 0xff) - 75) * 1000; 149 150 return 0; 151 } 152 153 return -EOPNOTSUPP; 154 } 155 156 static const struct hwmon_ops mv3310_hwmon_ops = { 157 .is_visible = mv3310_hwmon_is_visible, 158 .read = mv3310_hwmon_read, 159 }; 160 161 static u32 mv3310_hwmon_chip_config[] = { 162 HWMON_C_REGISTER_TZ | HWMON_C_UPDATE_INTERVAL, 163 0, 164 }; 165 166 static const struct hwmon_channel_info mv3310_hwmon_chip = { 167 .type = hwmon_chip, 168 .config = mv3310_hwmon_chip_config, 169 }; 170 171 static u32 mv3310_hwmon_temp_config[] = { 172 HWMON_T_INPUT, 173 0, 174 }; 175 176 static const struct hwmon_channel_info mv3310_hwmon_temp = { 177 .type = hwmon_temp, 178 .config = mv3310_hwmon_temp_config, 179 }; 180 181 static const struct hwmon_channel_info *mv3310_hwmon_info[] = { 182 &mv3310_hwmon_chip, 183 &mv3310_hwmon_temp, 184 NULL, 185 }; 186 187 static const struct hwmon_chip_info mv3310_hwmon_chip_info = { 188 .ops = &mv3310_hwmon_ops, 189 .info = mv3310_hwmon_info, 190 }; 191 192 static int mv3310_hwmon_config(struct phy_device *phydev, bool enable) 193 { 194 u16 val; 195 int ret; 196 197 if (phydev->drv->phy_id != MARVELL_PHY_ID_88X3310) 198 return 0; 199 200 ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, MV_V2_TEMP, 201 MV_V2_TEMP_UNKNOWN); 202 if (ret < 0) 203 return ret; 204 205 val = enable ? MV_V2_TEMP_CTRL_SAMPLE : MV_V2_TEMP_CTRL_DISABLE; 206 207 return phy_modify_mmd(phydev, MDIO_MMD_VEND2, MV_V2_TEMP_CTRL, 208 MV_V2_TEMP_CTRL_MASK, val); 209 } 210 211 static int mv3310_hwmon_probe(struct phy_device *phydev) 212 { 213 struct device *dev = &phydev->mdio.dev; 214 struct mv3310_priv *priv = dev_get_drvdata(&phydev->mdio.dev); 215 int i, j, ret; 216 217 priv->hwmon_name = devm_kstrdup(dev, dev_name(dev), GFP_KERNEL); 218 if (!priv->hwmon_name) 219 return -ENODEV; 220 221 for (i = j = 0; priv->hwmon_name[i]; i++) { 222 if (isalnum(priv->hwmon_name[i])) { 223 if (i != j) 224 priv->hwmon_name[j] = priv->hwmon_name[i]; 225 j++; 226 } 227 } 228 priv->hwmon_name[j] = '\0'; 229 230 ret = mv3310_hwmon_config(phydev, true); 231 if (ret) 232 return ret; 233 234 priv->hwmon_dev = devm_hwmon_device_register_with_info(dev, 235 priv->hwmon_name, phydev, 236 &mv3310_hwmon_chip_info, NULL); 237 238 return PTR_ERR_OR_ZERO(priv->hwmon_dev); 239 } 240 #else 241 static inline int mv3310_hwmon_config(struct phy_device *phydev, bool enable) 242 { 243 return 0; 244 } 245 246 static int mv3310_hwmon_probe(struct phy_device *phydev) 247 { 248 return 0; 249 } 250 #endif 251 252 static int mv3310_power_down(struct phy_device *phydev) 253 { 254 return phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, MV_V2_PORT_CTRL, 255 MV_V2_PORT_CTRL_PWRDOWN); 256 } 257 258 static int mv3310_power_up(struct phy_device *phydev) 259 { 260 struct mv3310_priv *priv = dev_get_drvdata(&phydev->mdio.dev); 261 int ret; 262 263 ret = phy_clear_bits_mmd(phydev, MDIO_MMD_VEND2, MV_V2_PORT_CTRL, 264 MV_V2_PORT_CTRL_PWRDOWN); 265 266 if (phydev->drv->phy_id != MARVELL_PHY_ID_88X3310 || 267 priv->firmware_ver < 0x00030000) 268 return ret; 269 270 return phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, MV_V2_PORT_CTRL, 271 MV_V2_PORT_CTRL_SWRST); 272 } 273 274 static int mv3310_reset(struct phy_device *phydev, u32 unit) 275 { 276 int val, err; 277 278 err = phy_modify_mmd(phydev, MDIO_MMD_PCS, unit + MDIO_CTRL1, 279 MDIO_CTRL1_RESET, MDIO_CTRL1_RESET); 280 if (err < 0) 281 return err; 282 283 return phy_read_mmd_poll_timeout(phydev, MDIO_MMD_PCS, 284 unit + MDIO_CTRL1, val, 285 !(val & MDIO_CTRL1_RESET), 286 5000, 100000, true); 287 } 288 289 static int mv3310_get_edpd(struct phy_device *phydev, u16 *edpd) 290 { 291 int val; 292 293 val = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_PCS_CSCR1); 294 if (val < 0) 295 return val; 296 297 switch (val & MV_PCS_CSCR1_ED_MASK) { 298 case MV_PCS_CSCR1_ED_NLP: 299 *edpd = 1000; 300 break; 301 case MV_PCS_CSCR1_ED_RX: 302 *edpd = ETHTOOL_PHY_EDPD_NO_TX; 303 break; 304 default: 305 *edpd = ETHTOOL_PHY_EDPD_DISABLE; 306 break; 307 } 308 return 0; 309 } 310 311 static int mv3310_set_edpd(struct phy_device *phydev, u16 edpd) 312 { 313 u16 val; 314 int err; 315 316 switch (edpd) { 317 case 1000: 318 case ETHTOOL_PHY_EDPD_DFLT_TX_MSECS: 319 val = MV_PCS_CSCR1_ED_NLP; 320 break; 321 322 case ETHTOOL_PHY_EDPD_NO_TX: 323 val = MV_PCS_CSCR1_ED_RX; 324 break; 325 326 case ETHTOOL_PHY_EDPD_DISABLE: 327 val = MV_PCS_CSCR1_ED_OFF; 328 break; 329 330 default: 331 return -EINVAL; 332 } 333 334 err = phy_modify_mmd_changed(phydev, MDIO_MMD_PCS, MV_PCS_CSCR1, 335 MV_PCS_CSCR1_ED_MASK, val); 336 if (err > 0) 337 err = mv3310_reset(phydev, MV_PCS_BASE_T); 338 339 return err; 340 } 341 342 static int mv3310_sfp_insert(void *upstream, const struct sfp_eeprom_id *id) 343 { 344 struct phy_device *phydev = upstream; 345 __ETHTOOL_DECLARE_LINK_MODE_MASK(support) = { 0, }; 346 phy_interface_t iface; 347 348 sfp_parse_support(phydev->sfp_bus, id, support); 349 iface = sfp_select_interface(phydev->sfp_bus, support); 350 351 if (iface != PHY_INTERFACE_MODE_10GBASER) { 352 dev_err(&phydev->mdio.dev, "incompatible SFP module inserted\n"); 353 return -EINVAL; 354 } 355 return 0; 356 } 357 358 static const struct sfp_upstream_ops mv3310_sfp_ops = { 359 .attach = phy_sfp_attach, 360 .detach = phy_sfp_detach, 361 .module_insert = mv3310_sfp_insert, 362 }; 363 364 static int mv3310_probe(struct phy_device *phydev) 365 { 366 struct mv3310_priv *priv; 367 u32 mmd_mask = MDIO_DEVS_PMAPMD | MDIO_DEVS_AN; 368 int ret; 369 370 if (!phydev->is_c45 || 371 (phydev->c45_ids.devices_in_package & mmd_mask) != mmd_mask) 372 return -ENODEV; 373 374 ret = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MV_PMA_BOOT); 375 if (ret < 0) 376 return ret; 377 378 if (ret & MV_PMA_BOOT_FATAL) { 379 dev_warn(&phydev->mdio.dev, 380 "PHY failed to boot firmware, status=%04x\n", ret); 381 return -ENODEV; 382 } 383 384 priv = devm_kzalloc(&phydev->mdio.dev, sizeof(*priv), GFP_KERNEL); 385 if (!priv) 386 return -ENOMEM; 387 388 dev_set_drvdata(&phydev->mdio.dev, priv); 389 390 ret = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MV_PMA_FW_VER0); 391 if (ret < 0) 392 return ret; 393 394 priv->firmware_ver = ret << 16; 395 396 ret = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MV_PMA_FW_VER1); 397 if (ret < 0) 398 return ret; 399 400 priv->firmware_ver |= ret; 401 402 phydev_info(phydev, "Firmware version %u.%u.%u.%u\n", 403 priv->firmware_ver >> 24, (priv->firmware_ver >> 16) & 255, 404 (priv->firmware_ver >> 8) & 255, priv->firmware_ver & 255); 405 406 /* Powering down the port when not in use saves about 600mW */ 407 ret = mv3310_power_down(phydev); 408 if (ret) 409 return ret; 410 411 ret = mv3310_hwmon_probe(phydev); 412 if (ret) 413 return ret; 414 415 return phy_sfp_probe(phydev, &mv3310_sfp_ops); 416 } 417 418 static void mv3310_remove(struct phy_device *phydev) 419 { 420 mv3310_hwmon_config(phydev, false); 421 } 422 423 static int mv3310_suspend(struct phy_device *phydev) 424 { 425 return mv3310_power_down(phydev); 426 } 427 428 static int mv3310_resume(struct phy_device *phydev) 429 { 430 int ret; 431 432 ret = mv3310_power_up(phydev); 433 if (ret) 434 return ret; 435 436 return mv3310_hwmon_config(phydev, true); 437 } 438 439 /* Some PHYs in the Alaska family such as the 88X3310 and the 88E2010 440 * don't set bit 14 in PMA Extended Abilities (1.11), although they do 441 * support 2.5GBASET and 5GBASET. For these models, we can still read their 442 * 2.5G/5G extended abilities register (1.21). We detect these models based on 443 * the PMA device identifier, with a mask matching models known to have this 444 * issue 445 */ 446 static bool mv3310_has_pma_ngbaset_quirk(struct phy_device *phydev) 447 { 448 if (!(phydev->c45_ids.devices_in_package & MDIO_DEVS_PMAPMD)) 449 return false; 450 451 /* Only some revisions of the 88X3310 family PMA seem to be impacted */ 452 return (phydev->c45_ids.device_ids[MDIO_MMD_PMAPMD] & 453 MV_PHY_ALASKA_NBT_QUIRK_MASK) == MV_PHY_ALASKA_NBT_QUIRK_REV; 454 } 455 456 static int mv3310_config_init(struct phy_device *phydev) 457 { 458 struct mv3310_priv *priv = dev_get_drvdata(&phydev->mdio.dev); 459 int err; 460 int val; 461 462 /* Check that the PHY interface type is compatible */ 463 if (phydev->interface != PHY_INTERFACE_MODE_SGMII && 464 phydev->interface != PHY_INTERFACE_MODE_2500BASEX && 465 phydev->interface != PHY_INTERFACE_MODE_XAUI && 466 phydev->interface != PHY_INTERFACE_MODE_RXAUI && 467 phydev->interface != PHY_INTERFACE_MODE_10GBASER) 468 return -ENODEV; 469 470 phydev->mdix_ctrl = ETH_TP_MDI_AUTO; 471 472 /* Power up so reset works */ 473 err = mv3310_power_up(phydev); 474 if (err) 475 return err; 476 477 val = phy_read_mmd(phydev, MDIO_MMD_VEND2, MV_V2_PORT_CTRL); 478 if (val < 0) 479 return val; 480 priv->rate_match = ((val & MV_V2_PORT_MAC_TYPE_MASK) == 481 MV_V2_PORT_MAC_TYPE_RATE_MATCH); 482 483 /* Enable EDPD mode - saving 600mW */ 484 return mv3310_set_edpd(phydev, ETHTOOL_PHY_EDPD_DFLT_TX_MSECS); 485 } 486 487 static int mv3310_get_features(struct phy_device *phydev) 488 { 489 int ret, val; 490 491 ret = genphy_c45_pma_read_abilities(phydev); 492 if (ret) 493 return ret; 494 495 if (mv3310_has_pma_ngbaset_quirk(phydev)) { 496 val = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, 497 MDIO_PMA_NG_EXTABLE); 498 if (val < 0) 499 return val; 500 501 linkmode_mod_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, 502 phydev->supported, 503 val & MDIO_PMA_NG_EXTABLE_2_5GBT); 504 505 linkmode_mod_bit(ETHTOOL_LINK_MODE_5000baseT_Full_BIT, 506 phydev->supported, 507 val & MDIO_PMA_NG_EXTABLE_5GBT); 508 } 509 510 return 0; 511 } 512 513 static int mv3310_config_mdix(struct phy_device *phydev) 514 { 515 u16 val; 516 int err; 517 518 switch (phydev->mdix_ctrl) { 519 case ETH_TP_MDI_AUTO: 520 val = MV_PCS_CSCR1_MDIX_AUTO; 521 break; 522 case ETH_TP_MDI_X: 523 val = MV_PCS_CSCR1_MDIX_MDIX; 524 break; 525 case ETH_TP_MDI: 526 val = MV_PCS_CSCR1_MDIX_MDI; 527 break; 528 default: 529 return -EINVAL; 530 } 531 532 err = phy_modify_mmd_changed(phydev, MDIO_MMD_PCS, MV_PCS_CSCR1, 533 MV_PCS_CSCR1_MDIX_MASK, val); 534 if (err > 0) 535 err = mv3310_reset(phydev, MV_PCS_BASE_T); 536 537 return err; 538 } 539 540 static int mv3310_config_aneg(struct phy_device *phydev) 541 { 542 bool changed = false; 543 u16 reg; 544 int ret; 545 546 ret = mv3310_config_mdix(phydev); 547 if (ret < 0) 548 return ret; 549 550 if (phydev->autoneg == AUTONEG_DISABLE) 551 return genphy_c45_pma_setup_forced(phydev); 552 553 ret = genphy_c45_an_config_aneg(phydev); 554 if (ret < 0) 555 return ret; 556 if (ret > 0) 557 changed = true; 558 559 /* Clause 45 has no standardized support for 1000BaseT, therefore 560 * use vendor registers for this mode. 561 */ 562 reg = linkmode_adv_to_mii_ctrl1000_t(phydev->advertising); 563 ret = phy_modify_mmd_changed(phydev, MDIO_MMD_AN, MV_AN_CTRL1000, 564 ADVERTISE_1000FULL | ADVERTISE_1000HALF, reg); 565 if (ret < 0) 566 return ret; 567 if (ret > 0) 568 changed = true; 569 570 return genphy_c45_check_and_restart_aneg(phydev, changed); 571 } 572 573 static int mv3310_aneg_done(struct phy_device *phydev) 574 { 575 int val; 576 577 val = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_PCS_BASE_R + MDIO_STAT1); 578 if (val < 0) 579 return val; 580 581 if (val & MDIO_STAT1_LSTATUS) 582 return 1; 583 584 return genphy_c45_aneg_done(phydev); 585 } 586 587 static void mv3310_update_interface(struct phy_device *phydev) 588 { 589 struct mv3310_priv *priv = dev_get_drvdata(&phydev->mdio.dev); 590 591 /* In "XFI with Rate Matching" mode the PHY interface is fixed at 592 * 10Gb. The PHY adapts the rate to actual wire speed with help of 593 * internal 16KB buffer. 594 */ 595 if (priv->rate_match) { 596 phydev->interface = PHY_INTERFACE_MODE_10GBASER; 597 return; 598 } 599 600 if ((phydev->interface == PHY_INTERFACE_MODE_SGMII || 601 phydev->interface == PHY_INTERFACE_MODE_2500BASEX || 602 phydev->interface == PHY_INTERFACE_MODE_10GBASER) && 603 phydev->link) { 604 /* The PHY automatically switches its serdes interface (and 605 * active PHYXS instance) between Cisco SGMII, 10GBase-R and 606 * 2500BaseX modes according to the speed. Florian suggests 607 * setting phydev->interface to communicate this to the MAC. 608 * Only do this if we are already in one of the above modes. 609 */ 610 switch (phydev->speed) { 611 case SPEED_10000: 612 phydev->interface = PHY_INTERFACE_MODE_10GBASER; 613 break; 614 case SPEED_2500: 615 phydev->interface = PHY_INTERFACE_MODE_2500BASEX; 616 break; 617 case SPEED_1000: 618 case SPEED_100: 619 case SPEED_10: 620 phydev->interface = PHY_INTERFACE_MODE_SGMII; 621 break; 622 default: 623 break; 624 } 625 } 626 } 627 628 /* 10GBASE-ER,LR,LRM,SR do not support autonegotiation. */ 629 static int mv3310_read_status_10gbaser(struct phy_device *phydev) 630 { 631 phydev->link = 1; 632 phydev->speed = SPEED_10000; 633 phydev->duplex = DUPLEX_FULL; 634 phydev->port = PORT_FIBRE; 635 636 return 0; 637 } 638 639 static int mv3310_read_status_copper(struct phy_device *phydev) 640 { 641 int cssr1, speed, val; 642 643 val = genphy_c45_read_link(phydev); 644 if (val < 0) 645 return val; 646 647 val = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_STAT1); 648 if (val < 0) 649 return val; 650 651 cssr1 = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_PCS_CSSR1); 652 if (cssr1 < 0) 653 return val; 654 655 /* If the link settings are not resolved, mark the link down */ 656 if (!(cssr1 & MV_PCS_CSSR1_RESOLVED)) { 657 phydev->link = 0; 658 return 0; 659 } 660 661 /* Read the copper link settings */ 662 speed = cssr1 & MV_PCS_CSSR1_SPD1_MASK; 663 if (speed == MV_PCS_CSSR1_SPD1_SPD2) 664 speed |= cssr1 & MV_PCS_CSSR1_SPD2_MASK; 665 666 switch (speed) { 667 case MV_PCS_CSSR1_SPD1_SPD2 | MV_PCS_CSSR1_SPD2_10000: 668 phydev->speed = SPEED_10000; 669 break; 670 671 case MV_PCS_CSSR1_SPD1_SPD2 | MV_PCS_CSSR1_SPD2_5000: 672 phydev->speed = SPEED_5000; 673 break; 674 675 case MV_PCS_CSSR1_SPD1_SPD2 | MV_PCS_CSSR1_SPD2_2500: 676 phydev->speed = SPEED_2500; 677 break; 678 679 case MV_PCS_CSSR1_SPD1_1000: 680 phydev->speed = SPEED_1000; 681 break; 682 683 case MV_PCS_CSSR1_SPD1_100: 684 phydev->speed = SPEED_100; 685 break; 686 687 case MV_PCS_CSSR1_SPD1_10: 688 phydev->speed = SPEED_10; 689 break; 690 } 691 692 phydev->duplex = cssr1 & MV_PCS_CSSR1_DUPLEX_FULL ? 693 DUPLEX_FULL : DUPLEX_HALF; 694 phydev->port = PORT_TP; 695 phydev->mdix = cssr1 & MV_PCS_CSSR1_MDIX ? 696 ETH_TP_MDI_X : ETH_TP_MDI; 697 698 if (val & MDIO_AN_STAT1_COMPLETE) { 699 val = genphy_c45_read_lpa(phydev); 700 if (val < 0) 701 return val; 702 703 /* Read the link partner's 1G advertisement */ 704 val = phy_read_mmd(phydev, MDIO_MMD_AN, MV_AN_STAT1000); 705 if (val < 0) 706 return val; 707 708 mii_stat1000_mod_linkmode_lpa_t(phydev->lp_advertising, val); 709 710 /* Update the pause status */ 711 phy_resolve_aneg_pause(phydev); 712 } 713 714 return 0; 715 } 716 717 static int mv3310_read_status(struct phy_device *phydev) 718 { 719 int err, val; 720 721 phydev->speed = SPEED_UNKNOWN; 722 phydev->duplex = DUPLEX_UNKNOWN; 723 linkmode_zero(phydev->lp_advertising); 724 phydev->link = 0; 725 phydev->pause = 0; 726 phydev->asym_pause = 0; 727 phydev->mdix = ETH_TP_MDI_INVALID; 728 729 val = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_PCS_BASE_R + MDIO_STAT1); 730 if (val < 0) 731 return val; 732 733 if (val & MDIO_STAT1_LSTATUS) 734 err = mv3310_read_status_10gbaser(phydev); 735 else 736 err = mv3310_read_status_copper(phydev); 737 if (err < 0) 738 return err; 739 740 if (phydev->link) 741 mv3310_update_interface(phydev); 742 743 return 0; 744 } 745 746 static int mv3310_get_tunable(struct phy_device *phydev, 747 struct ethtool_tunable *tuna, void *data) 748 { 749 switch (tuna->id) { 750 case ETHTOOL_PHY_EDPD: 751 return mv3310_get_edpd(phydev, data); 752 default: 753 return -EOPNOTSUPP; 754 } 755 } 756 757 static int mv3310_set_tunable(struct phy_device *phydev, 758 struct ethtool_tunable *tuna, const void *data) 759 { 760 switch (tuna->id) { 761 case ETHTOOL_PHY_EDPD: 762 return mv3310_set_edpd(phydev, *(u16 *)data); 763 default: 764 return -EOPNOTSUPP; 765 } 766 } 767 768 static struct phy_driver mv3310_drivers[] = { 769 { 770 .phy_id = MARVELL_PHY_ID_88X3310, 771 .phy_id_mask = MARVELL_PHY_ID_MASK, 772 .name = "mv88x3310", 773 .get_features = mv3310_get_features, 774 .config_init = mv3310_config_init, 775 .probe = mv3310_probe, 776 .suspend = mv3310_suspend, 777 .resume = mv3310_resume, 778 .config_aneg = mv3310_config_aneg, 779 .aneg_done = mv3310_aneg_done, 780 .read_status = mv3310_read_status, 781 .get_tunable = mv3310_get_tunable, 782 .set_tunable = mv3310_set_tunable, 783 .remove = mv3310_remove, 784 }, 785 { 786 .phy_id = MARVELL_PHY_ID_88E2110, 787 .phy_id_mask = MARVELL_PHY_ID_MASK, 788 .name = "mv88x2110", 789 .probe = mv3310_probe, 790 .suspend = mv3310_suspend, 791 .resume = mv3310_resume, 792 .config_init = mv3310_config_init, 793 .config_aneg = mv3310_config_aneg, 794 .aneg_done = mv3310_aneg_done, 795 .read_status = mv3310_read_status, 796 .get_tunable = mv3310_get_tunable, 797 .set_tunable = mv3310_set_tunable, 798 .remove = mv3310_remove, 799 }, 800 }; 801 802 module_phy_driver(mv3310_drivers); 803 804 static struct mdio_device_id __maybe_unused mv3310_tbl[] = { 805 { MARVELL_PHY_ID_88X3310, MARVELL_PHY_ID_MASK }, 806 { MARVELL_PHY_ID_88E2110, MARVELL_PHY_ID_MASK }, 807 { }, 808 }; 809 MODULE_DEVICE_TABLE(mdio, mv3310_tbl); 810 MODULE_DESCRIPTION("Marvell Alaska X 10Gigabit Ethernet PHY driver (MV88X3310)"); 811 MODULE_LICENSE("GPL"); 812