1 /* 2 * Broadcom BCM7xxx internal transceivers support. 3 * 4 * Copyright (C) 2014-2017 Broadcom 5 * 6 * This program is free software; you can redistribute it and/or 7 * modify it under the terms of the GNU General Public License 8 * as published by the Free Software Foundation; either version 9 * 2 of the License, or (at your option) any later version. 10 */ 11 12 #include <linux/module.h> 13 #include <linux/phy.h> 14 #include <linux/delay.h> 15 #include "bcm-phy-lib.h" 16 #include <linux/bitops.h> 17 #include <linux/brcmphy.h> 18 #include <linux/mdio.h> 19 20 /* Broadcom BCM7xxx internal PHY registers */ 21 22 /* EPHY only register definitions */ 23 #define MII_BCM7XXX_100TX_AUX_CTL 0x10 24 #define MII_BCM7XXX_100TX_FALSE_CAR 0x13 25 #define MII_BCM7XXX_100TX_DISC 0x14 26 #define MII_BCM7XXX_AUX_MODE 0x1d 27 #define MII_BCM7XXX_64CLK_MDIO BIT(12) 28 #define MII_BCM7XXX_TEST 0x1f 29 #define MII_BCM7XXX_SHD_MODE_2 BIT(2) 30 #define MII_BCM7XXX_SHD_2_ADDR_CTRL 0xe 31 #define MII_BCM7XXX_SHD_2_CTRL_STAT 0xf 32 #define MII_BCM7XXX_SHD_2_BIAS_TRIM 0x1a 33 #define MII_BCM7XXX_SHD_3_AN_EEE_ADV 0x3 34 #define MII_BCM7XXX_SHD_3_PCS_CTRL_2 0x6 35 #define MII_BCM7XXX_PCS_CTRL_2_DEF 0x4400 36 #define MII_BCM7XXX_SHD_3_AN_STAT 0xb 37 #define MII_BCM7XXX_AN_NULL_MSG_EN BIT(0) 38 #define MII_BCM7XXX_AN_EEE_EN BIT(1) 39 #define MII_BCM7XXX_SHD_3_EEE_THRESH 0xe 40 #define MII_BCM7XXX_EEE_THRESH_DEF 0x50 41 #define MII_BCM7XXX_SHD_3_TL4 0x23 42 #define MII_BCM7XXX_TL4_RST_MSK (BIT(2) | BIT(1)) 43 44 /* 28nm only register definitions */ 45 #define MISC_ADDR(base, channel) base, channel 46 47 #define DSP_TAP10 MISC_ADDR(0x0a, 0) 48 #define PLL_PLLCTRL_1 MISC_ADDR(0x32, 1) 49 #define PLL_PLLCTRL_2 MISC_ADDR(0x32, 2) 50 #define PLL_PLLCTRL_4 MISC_ADDR(0x33, 0) 51 52 #define AFE_RXCONFIG_0 MISC_ADDR(0x38, 0) 53 #define AFE_RXCONFIG_1 MISC_ADDR(0x38, 1) 54 #define AFE_RXCONFIG_2 MISC_ADDR(0x38, 2) 55 #define AFE_RX_LP_COUNTER MISC_ADDR(0x38, 3) 56 #define AFE_TX_CONFIG MISC_ADDR(0x39, 0) 57 #define AFE_VDCA_ICTRL_0 MISC_ADDR(0x39, 1) 58 #define AFE_VDAC_OTHERS_0 MISC_ADDR(0x39, 3) 59 #define AFE_HPF_TRIM_OTHERS MISC_ADDR(0x3a, 0) 60 61 struct bcm7xxx_phy_priv { 62 u64 *stats; 63 }; 64 65 static void r_rc_cal_reset(struct phy_device *phydev) 66 { 67 /* Reset R_CAL/RC_CAL Engine */ 68 bcm_phy_write_exp_sel(phydev, 0x00b0, 0x0010); 69 70 /* Disable Reset R_AL/RC_CAL Engine */ 71 bcm_phy_write_exp_sel(phydev, 0x00b0, 0x0000); 72 } 73 74 static int bcm7xxx_28nm_b0_afe_config_init(struct phy_device *phydev) 75 { 76 /* Increase VCO range to prevent unlocking problem of PLL at low 77 * temp 78 */ 79 bcm_phy_write_misc(phydev, PLL_PLLCTRL_1, 0x0048); 80 81 /* Change Ki to 011 */ 82 bcm_phy_write_misc(phydev, PLL_PLLCTRL_2, 0x021b); 83 84 /* Disable loading of TVCO buffer to bandgap, set bandgap trim 85 * to 111 86 */ 87 bcm_phy_write_misc(phydev, PLL_PLLCTRL_4, 0x0e20); 88 89 /* Adjust bias current trim by -3 */ 90 bcm_phy_write_misc(phydev, DSP_TAP10, 0x690b); 91 92 /* Switch to CORE_BASE1E */ 93 phy_write(phydev, MII_BRCM_CORE_BASE1E, 0xd); 94 95 r_rc_cal_reset(phydev); 96 97 /* write AFE_RXCONFIG_0 */ 98 bcm_phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb19); 99 100 /* write AFE_RXCONFIG_1 */ 101 bcm_phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9a3f); 102 103 /* write AFE_RX_LP_COUNTER */ 104 bcm_phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0); 105 106 /* write AFE_HPF_TRIM_OTHERS */ 107 bcm_phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x000b); 108 109 /* write AFTE_TX_CONFIG */ 110 bcm_phy_write_misc(phydev, AFE_TX_CONFIG, 0x0800); 111 112 return 0; 113 } 114 115 static int bcm7xxx_28nm_d0_afe_config_init(struct phy_device *phydev) 116 { 117 /* AFE_RXCONFIG_0 */ 118 bcm_phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb15); 119 120 /* AFE_RXCONFIG_1 */ 121 bcm_phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f); 122 123 /* AFE_RXCONFIG_2, set rCal offset for HT=0 code and LT=-2 code */ 124 bcm_phy_write_misc(phydev, AFE_RXCONFIG_2, 0x2003); 125 126 /* AFE_RX_LP_COUNTER, set RX bandwidth to maximum */ 127 bcm_phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0); 128 129 /* AFE_TX_CONFIG, set 100BT Cfeed=011 to improve rise/fall time */ 130 bcm_phy_write_misc(phydev, AFE_TX_CONFIG, 0x431); 131 132 /* AFE_VDCA_ICTRL_0, set Iq=1101 instead of 0111 for AB symmetry */ 133 bcm_phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da); 134 135 /* AFE_VDAC_OTHERS_0, set 1000BT Cidac=010 for all ports */ 136 bcm_phy_write_misc(phydev, AFE_VDAC_OTHERS_0, 0xa020); 137 138 /* AFE_HPF_TRIM_OTHERS, set 100Tx/10BT to -4.5% swing and set rCal 139 * offset for HT=0 code 140 */ 141 bcm_phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3); 142 143 /* CORE_BASE1E, force trim to overwrite and set I_ext trim to 0000 */ 144 phy_write(phydev, MII_BRCM_CORE_BASE1E, 0x0010); 145 146 /* DSP_TAP10, adjust bias current trim (+0% swing, +0 tick) */ 147 bcm_phy_write_misc(phydev, DSP_TAP10, 0x011b); 148 149 /* Reset R_CAL/RC_CAL engine */ 150 r_rc_cal_reset(phydev); 151 152 return 0; 153 } 154 155 static int bcm7xxx_28nm_e0_plus_afe_config_init(struct phy_device *phydev) 156 { 157 /* AFE_RXCONFIG_1, provide more margin for INL/DNL measurement */ 158 bcm_phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f); 159 160 /* AFE_TX_CONFIG, set 100BT Cfeed=011 to improve rise/fall time */ 161 bcm_phy_write_misc(phydev, AFE_TX_CONFIG, 0x431); 162 163 /* AFE_VDCA_ICTRL_0, set Iq=1101 instead of 0111 for AB symmetry */ 164 bcm_phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da); 165 166 /* AFE_HPF_TRIM_OTHERS, set 100Tx/10BT to -4.5% swing and set rCal 167 * offset for HT=0 code 168 */ 169 bcm_phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3); 170 171 /* CORE_BASE1E, force trim to overwrite and set I_ext trim to 0000 */ 172 phy_write(phydev, MII_BRCM_CORE_BASE1E, 0x0010); 173 174 /* DSP_TAP10, adjust bias current trim (+0% swing, +0 tick) */ 175 bcm_phy_write_misc(phydev, DSP_TAP10, 0x011b); 176 177 /* Reset R_CAL/RC_CAL engine */ 178 r_rc_cal_reset(phydev); 179 180 return 0; 181 } 182 183 static int bcm7xxx_28nm_a0_patch_afe_config_init(struct phy_device *phydev) 184 { 185 /* +1 RC_CAL codes for RL centering for both LT and HT conditions */ 186 bcm_phy_write_misc(phydev, AFE_RXCONFIG_2, 0xd003); 187 188 /* Cut master bias current by 2% to compensate for RC_CAL offset */ 189 bcm_phy_write_misc(phydev, DSP_TAP10, 0x791b); 190 191 /* Improve hybrid leakage */ 192 bcm_phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x10e3); 193 194 /* Change rx_on_tune 8 to 0xf */ 195 bcm_phy_write_misc(phydev, 0x21, 0x2, 0x87f6); 196 197 /* Change 100Tx EEE bandwidth */ 198 bcm_phy_write_misc(phydev, 0x22, 0x2, 0x017d); 199 200 /* Enable ffe zero detection for Vitesse interoperability */ 201 bcm_phy_write_misc(phydev, 0x26, 0x2, 0x0015); 202 203 r_rc_cal_reset(phydev); 204 205 return 0; 206 } 207 208 static int bcm7xxx_28nm_config_init(struct phy_device *phydev) 209 { 210 u8 rev = PHY_BRCM_7XXX_REV(phydev->dev_flags); 211 u8 patch = PHY_BRCM_7XXX_PATCH(phydev->dev_flags); 212 u8 count; 213 int ret = 0; 214 215 /* Newer devices have moved the revision information back into a 216 * standard location in MII_PHYS_ID[23] 217 */ 218 if (rev == 0) 219 rev = phydev->phy_id & ~phydev->drv->phy_id_mask; 220 221 pr_info_once("%s: %s PHY revision: 0x%02x, patch: %d\n", 222 phydev_name(phydev), phydev->drv->name, rev, patch); 223 224 /* Dummy read to a register to workaround an issue upon reset where the 225 * internal inverter may not allow the first MDIO transaction to pass 226 * the MDIO management controller and make us return 0xffff for such 227 * reads. 228 */ 229 phy_read(phydev, MII_BMSR); 230 231 switch (rev) { 232 case 0xa0: 233 case 0xb0: 234 ret = bcm7xxx_28nm_b0_afe_config_init(phydev); 235 break; 236 case 0xd0: 237 ret = bcm7xxx_28nm_d0_afe_config_init(phydev); 238 break; 239 case 0xe0: 240 case 0xf0: 241 /* Rev G0 introduces a roll over */ 242 case 0x10: 243 ret = bcm7xxx_28nm_e0_plus_afe_config_init(phydev); 244 break; 245 case 0x01: 246 ret = bcm7xxx_28nm_a0_patch_afe_config_init(phydev); 247 break; 248 default: 249 break; 250 } 251 252 if (ret) 253 return ret; 254 255 ret = bcm_phy_downshift_get(phydev, &count); 256 if (ret) 257 return ret; 258 259 /* Only enable EEE if Wirespeed/downshift is disabled */ 260 ret = bcm_phy_set_eee(phydev, count == DOWNSHIFT_DEV_DISABLE); 261 if (ret) 262 return ret; 263 264 return bcm_phy_enable_apd(phydev, true); 265 } 266 267 static int bcm7xxx_28nm_resume(struct phy_device *phydev) 268 { 269 int ret; 270 271 /* Re-apply workarounds coming out suspend/resume */ 272 ret = bcm7xxx_28nm_config_init(phydev); 273 if (ret) 274 return ret; 275 276 /* 28nm Gigabit PHYs come out of reset without any half-duplex 277 * or "hub" compliant advertised mode, fix that. This does not 278 * cause any problems with the PHY library since genphy_config_aneg() 279 * gracefully handles auto-negotiated and forced modes. 280 */ 281 return genphy_config_aneg(phydev); 282 } 283 284 static int phy_set_clr_bits(struct phy_device *dev, int location, 285 int set_mask, int clr_mask) 286 { 287 int v, ret; 288 289 v = phy_read(dev, location); 290 if (v < 0) 291 return v; 292 293 v &= ~clr_mask; 294 v |= set_mask; 295 296 ret = phy_write(dev, location, v); 297 if (ret < 0) 298 return ret; 299 300 return v; 301 } 302 303 static int bcm7xxx_28nm_ephy_01_afe_config_init(struct phy_device *phydev) 304 { 305 int ret; 306 307 /* set shadow mode 2 */ 308 ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST, 309 MII_BCM7XXX_SHD_MODE_2, 0); 310 if (ret < 0) 311 return ret; 312 313 /* Set current trim values INT_trim = -1, Ext_trim =0 */ 314 ret = phy_write(phydev, MII_BCM7XXX_SHD_2_BIAS_TRIM, 0x3BE0); 315 if (ret < 0) 316 goto reset_shadow_mode; 317 318 /* Cal reset */ 319 ret = phy_write(phydev, MII_BCM7XXX_SHD_2_ADDR_CTRL, 320 MII_BCM7XXX_SHD_3_TL4); 321 if (ret < 0) 322 goto reset_shadow_mode; 323 ret = phy_set_clr_bits(phydev, MII_BCM7XXX_SHD_2_CTRL_STAT, 324 MII_BCM7XXX_TL4_RST_MSK, 0); 325 if (ret < 0) 326 goto reset_shadow_mode; 327 328 /* Cal reset disable */ 329 ret = phy_write(phydev, MII_BCM7XXX_SHD_2_ADDR_CTRL, 330 MII_BCM7XXX_SHD_3_TL4); 331 if (ret < 0) 332 goto reset_shadow_mode; 333 ret = phy_set_clr_bits(phydev, MII_BCM7XXX_SHD_2_CTRL_STAT, 334 0, MII_BCM7XXX_TL4_RST_MSK); 335 if (ret < 0) 336 goto reset_shadow_mode; 337 338 reset_shadow_mode: 339 /* reset shadow mode 2 */ 340 ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST, 0, 341 MII_BCM7XXX_SHD_MODE_2); 342 if (ret < 0) 343 return ret; 344 345 return 0; 346 } 347 348 /* The 28nm EPHY does not support Clause 45 (MMD) used by bcm-phy-lib */ 349 static int bcm7xxx_28nm_ephy_apd_enable(struct phy_device *phydev) 350 { 351 int ret; 352 353 /* set shadow mode 1 */ 354 ret = phy_set_clr_bits(phydev, MII_BRCM_FET_BRCMTEST, 355 MII_BRCM_FET_BT_SRE, 0); 356 if (ret < 0) 357 return ret; 358 359 /* Enable auto-power down */ 360 ret = phy_set_clr_bits(phydev, MII_BRCM_FET_SHDW_AUXSTAT2, 361 MII_BRCM_FET_SHDW_AS2_APDE, 0); 362 if (ret < 0) 363 return ret; 364 365 /* reset shadow mode 1 */ 366 ret = phy_set_clr_bits(phydev, MII_BRCM_FET_BRCMTEST, 0, 367 MII_BRCM_FET_BT_SRE); 368 if (ret < 0) 369 return ret; 370 371 return 0; 372 } 373 374 static int bcm7xxx_28nm_ephy_eee_enable(struct phy_device *phydev) 375 { 376 int ret; 377 378 /* set shadow mode 2 */ 379 ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST, 380 MII_BCM7XXX_SHD_MODE_2, 0); 381 if (ret < 0) 382 return ret; 383 384 /* Advertise supported modes */ 385 ret = phy_write(phydev, MII_BCM7XXX_SHD_2_ADDR_CTRL, 386 MII_BCM7XXX_SHD_3_AN_EEE_ADV); 387 if (ret < 0) 388 goto reset_shadow_mode; 389 ret = phy_write(phydev, MII_BCM7XXX_SHD_2_CTRL_STAT, 390 MDIO_EEE_100TX); 391 if (ret < 0) 392 goto reset_shadow_mode; 393 394 /* Restore Defaults */ 395 ret = phy_write(phydev, MII_BCM7XXX_SHD_2_ADDR_CTRL, 396 MII_BCM7XXX_SHD_3_PCS_CTRL_2); 397 if (ret < 0) 398 goto reset_shadow_mode; 399 ret = phy_write(phydev, MII_BCM7XXX_SHD_2_CTRL_STAT, 400 MII_BCM7XXX_PCS_CTRL_2_DEF); 401 if (ret < 0) 402 goto reset_shadow_mode; 403 404 ret = phy_write(phydev, MII_BCM7XXX_SHD_2_ADDR_CTRL, 405 MII_BCM7XXX_SHD_3_EEE_THRESH); 406 if (ret < 0) 407 goto reset_shadow_mode; 408 ret = phy_write(phydev, MII_BCM7XXX_SHD_2_CTRL_STAT, 409 MII_BCM7XXX_EEE_THRESH_DEF); 410 if (ret < 0) 411 goto reset_shadow_mode; 412 413 /* Enable EEE autonegotiation */ 414 ret = phy_write(phydev, MII_BCM7XXX_SHD_2_ADDR_CTRL, 415 MII_BCM7XXX_SHD_3_AN_STAT); 416 if (ret < 0) 417 goto reset_shadow_mode; 418 ret = phy_write(phydev, MII_BCM7XXX_SHD_2_CTRL_STAT, 419 (MII_BCM7XXX_AN_NULL_MSG_EN | MII_BCM7XXX_AN_EEE_EN)); 420 if (ret < 0) 421 goto reset_shadow_mode; 422 423 reset_shadow_mode: 424 /* reset shadow mode 2 */ 425 ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST, 0, 426 MII_BCM7XXX_SHD_MODE_2); 427 if (ret < 0) 428 return ret; 429 430 /* Restart autoneg */ 431 phy_write(phydev, MII_BMCR, 432 (BMCR_SPEED100 | BMCR_ANENABLE | BMCR_ANRESTART)); 433 434 return 0; 435 } 436 437 static int bcm7xxx_28nm_ephy_config_init(struct phy_device *phydev) 438 { 439 u8 rev = phydev->phy_id & ~phydev->drv->phy_id_mask; 440 int ret = 0; 441 442 pr_info_once("%s: %s PHY revision: 0x%02x\n", 443 phydev_name(phydev), phydev->drv->name, rev); 444 445 /* Dummy read to a register to workaround a possible issue upon reset 446 * where the internal inverter may not allow the first MDIO transaction 447 * to pass the MDIO management controller and make us return 0xffff for 448 * such reads. 449 */ 450 phy_read(phydev, MII_BMSR); 451 452 /* Apply AFE software work-around if necessary */ 453 if (rev == 0x01) { 454 ret = bcm7xxx_28nm_ephy_01_afe_config_init(phydev); 455 if (ret) 456 return ret; 457 } 458 459 ret = bcm7xxx_28nm_ephy_eee_enable(phydev); 460 if (ret) 461 return ret; 462 463 return bcm7xxx_28nm_ephy_apd_enable(phydev); 464 } 465 466 static int bcm7xxx_28nm_ephy_resume(struct phy_device *phydev) 467 { 468 int ret; 469 470 /* Re-apply workarounds coming out suspend/resume */ 471 ret = bcm7xxx_28nm_ephy_config_init(phydev); 472 if (ret) 473 return ret; 474 475 return genphy_config_aneg(phydev); 476 } 477 478 static int bcm7xxx_config_init(struct phy_device *phydev) 479 { 480 int ret; 481 482 /* Enable 64 clock MDIO */ 483 phy_write(phydev, MII_BCM7XXX_AUX_MODE, MII_BCM7XXX_64CLK_MDIO); 484 phy_read(phydev, MII_BCM7XXX_AUX_MODE); 485 486 /* set shadow mode 2 */ 487 ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST, 488 MII_BCM7XXX_SHD_MODE_2, MII_BCM7XXX_SHD_MODE_2); 489 if (ret < 0) 490 return ret; 491 492 /* set iddq_clkbias */ 493 phy_write(phydev, MII_BCM7XXX_100TX_DISC, 0x0F00); 494 udelay(10); 495 496 /* reset iddq_clkbias */ 497 phy_write(phydev, MII_BCM7XXX_100TX_DISC, 0x0C00); 498 499 phy_write(phydev, MII_BCM7XXX_100TX_FALSE_CAR, 0x7555); 500 501 /* reset shadow mode 2 */ 502 ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST, 0, MII_BCM7XXX_SHD_MODE_2); 503 if (ret < 0) 504 return ret; 505 506 return 0; 507 } 508 509 /* Workaround for putting the PHY in IDDQ mode, required 510 * for all BCM7XXX 40nm and 65nm PHYs 511 */ 512 static int bcm7xxx_suspend(struct phy_device *phydev) 513 { 514 int ret; 515 static const struct bcm7xxx_regs { 516 int reg; 517 u16 value; 518 } bcm7xxx_suspend_cfg[] = { 519 { MII_BCM7XXX_TEST, 0x008b }, 520 { MII_BCM7XXX_100TX_AUX_CTL, 0x01c0 }, 521 { MII_BCM7XXX_100TX_DISC, 0x7000 }, 522 { MII_BCM7XXX_TEST, 0x000f }, 523 { MII_BCM7XXX_100TX_AUX_CTL, 0x20d0 }, 524 { MII_BCM7XXX_TEST, 0x000b }, 525 }; 526 unsigned int i; 527 528 for (i = 0; i < ARRAY_SIZE(bcm7xxx_suspend_cfg); i++) { 529 ret = phy_write(phydev, 530 bcm7xxx_suspend_cfg[i].reg, 531 bcm7xxx_suspend_cfg[i].value); 532 if (ret) 533 return ret; 534 } 535 536 return 0; 537 } 538 539 static int bcm7xxx_28nm_get_tunable(struct phy_device *phydev, 540 struct ethtool_tunable *tuna, 541 void *data) 542 { 543 switch (tuna->id) { 544 case ETHTOOL_PHY_DOWNSHIFT: 545 return bcm_phy_downshift_get(phydev, (u8 *)data); 546 default: 547 return -EOPNOTSUPP; 548 } 549 } 550 551 static int bcm7xxx_28nm_set_tunable(struct phy_device *phydev, 552 struct ethtool_tunable *tuna, 553 const void *data) 554 { 555 u8 count = *(u8 *)data; 556 int ret; 557 558 switch (tuna->id) { 559 case ETHTOOL_PHY_DOWNSHIFT: 560 ret = bcm_phy_downshift_set(phydev, count); 561 break; 562 default: 563 return -EOPNOTSUPP; 564 } 565 566 if (ret) 567 return ret; 568 569 /* Disable EEE advertisement since this prevents the PHY 570 * from successfully linking up, trigger auto-negotiation restart 571 * to let the MAC decide what to do. 572 */ 573 ret = bcm_phy_set_eee(phydev, count == DOWNSHIFT_DEV_DISABLE); 574 if (ret) 575 return ret; 576 577 return genphy_restart_aneg(phydev); 578 } 579 580 static void bcm7xxx_28nm_get_phy_stats(struct phy_device *phydev, 581 struct ethtool_stats *stats, u64 *data) 582 { 583 struct bcm7xxx_phy_priv *priv = phydev->priv; 584 585 bcm_phy_get_stats(phydev, priv->stats, stats, data); 586 } 587 588 static int bcm7xxx_28nm_probe(struct phy_device *phydev) 589 { 590 struct bcm7xxx_phy_priv *priv; 591 592 priv = devm_kzalloc(&phydev->mdio.dev, sizeof(*priv), GFP_KERNEL); 593 if (!priv) 594 return -ENOMEM; 595 596 phydev->priv = priv; 597 598 priv->stats = devm_kcalloc(&phydev->mdio.dev, 599 bcm_phy_get_sset_count(phydev), sizeof(u64), 600 GFP_KERNEL); 601 if (!priv->stats) 602 return -ENOMEM; 603 604 return 0; 605 } 606 607 #define BCM7XXX_28NM_GPHY(_oui, _name) \ 608 { \ 609 .phy_id = (_oui), \ 610 .phy_id_mask = 0xfffffff0, \ 611 .name = _name, \ 612 .features = PHY_GBIT_FEATURES, \ 613 .flags = PHY_IS_INTERNAL, \ 614 .config_init = bcm7xxx_28nm_config_init, \ 615 .resume = bcm7xxx_28nm_resume, \ 616 .get_tunable = bcm7xxx_28nm_get_tunable, \ 617 .set_tunable = bcm7xxx_28nm_set_tunable, \ 618 .get_sset_count = bcm_phy_get_sset_count, \ 619 .get_strings = bcm_phy_get_strings, \ 620 .get_stats = bcm7xxx_28nm_get_phy_stats, \ 621 .probe = bcm7xxx_28nm_probe, \ 622 } 623 624 #define BCM7XXX_28NM_EPHY(_oui, _name) \ 625 { \ 626 .phy_id = (_oui), \ 627 .phy_id_mask = 0xfffffff0, \ 628 .name = _name, \ 629 .features = PHY_BASIC_FEATURES, \ 630 .flags = PHY_IS_INTERNAL, \ 631 .config_init = bcm7xxx_28nm_ephy_config_init, \ 632 .resume = bcm7xxx_28nm_ephy_resume, \ 633 .get_sset_count = bcm_phy_get_sset_count, \ 634 .get_strings = bcm_phy_get_strings, \ 635 .get_stats = bcm7xxx_28nm_get_phy_stats, \ 636 .probe = bcm7xxx_28nm_probe, \ 637 } 638 639 #define BCM7XXX_40NM_EPHY(_oui, _name) \ 640 { \ 641 .phy_id = (_oui), \ 642 .phy_id_mask = 0xfffffff0, \ 643 .name = _name, \ 644 .features = PHY_BASIC_FEATURES, \ 645 .flags = PHY_IS_INTERNAL, \ 646 .config_init = bcm7xxx_config_init, \ 647 .suspend = bcm7xxx_suspend, \ 648 .resume = bcm7xxx_config_init, \ 649 } 650 651 static struct phy_driver bcm7xxx_driver[] = { 652 BCM7XXX_28NM_GPHY(PHY_ID_BCM7250, "Broadcom BCM7250"), 653 BCM7XXX_28NM_EPHY(PHY_ID_BCM7260, "Broadcom BCM7260"), 654 BCM7XXX_28NM_EPHY(PHY_ID_BCM7268, "Broadcom BCM7268"), 655 BCM7XXX_28NM_EPHY(PHY_ID_BCM7271, "Broadcom BCM7271"), 656 BCM7XXX_28NM_GPHY(PHY_ID_BCM7278, "Broadcom BCM7278"), 657 BCM7XXX_28NM_GPHY(PHY_ID_BCM7364, "Broadcom BCM7364"), 658 BCM7XXX_28NM_GPHY(PHY_ID_BCM7366, "Broadcom BCM7366"), 659 BCM7XXX_28NM_GPHY(PHY_ID_BCM74371, "Broadcom BCM74371"), 660 BCM7XXX_28NM_GPHY(PHY_ID_BCM7439, "Broadcom BCM7439"), 661 BCM7XXX_28NM_GPHY(PHY_ID_BCM7439_2, "Broadcom BCM7439 (2)"), 662 BCM7XXX_28NM_GPHY(PHY_ID_BCM7445, "Broadcom BCM7445"), 663 BCM7XXX_28NM_GPHY(PHY_ID_BCM_OMEGA, "Broadcom Omega Combo GPHY"), 664 BCM7XXX_40NM_EPHY(PHY_ID_BCM7346, "Broadcom BCM7346"), 665 BCM7XXX_40NM_EPHY(PHY_ID_BCM7362, "Broadcom BCM7362"), 666 BCM7XXX_40NM_EPHY(PHY_ID_BCM7425, "Broadcom BCM7425"), 667 BCM7XXX_40NM_EPHY(PHY_ID_BCM7429, "Broadcom BCM7429"), 668 BCM7XXX_40NM_EPHY(PHY_ID_BCM7435, "Broadcom BCM7435"), 669 }; 670 671 static struct mdio_device_id __maybe_unused bcm7xxx_tbl[] = { 672 { PHY_ID_BCM7250, 0xfffffff0, }, 673 { PHY_ID_BCM7260, 0xfffffff0, }, 674 { PHY_ID_BCM7268, 0xfffffff0, }, 675 { PHY_ID_BCM7271, 0xfffffff0, }, 676 { PHY_ID_BCM7278, 0xfffffff0, }, 677 { PHY_ID_BCM7364, 0xfffffff0, }, 678 { PHY_ID_BCM7366, 0xfffffff0, }, 679 { PHY_ID_BCM7346, 0xfffffff0, }, 680 { PHY_ID_BCM7362, 0xfffffff0, }, 681 { PHY_ID_BCM7425, 0xfffffff0, }, 682 { PHY_ID_BCM7429, 0xfffffff0, }, 683 { PHY_ID_BCM74371, 0xfffffff0, }, 684 { PHY_ID_BCM7439, 0xfffffff0, }, 685 { PHY_ID_BCM7435, 0xfffffff0, }, 686 { PHY_ID_BCM7445, 0xfffffff0, }, 687 { } 688 }; 689 690 module_phy_driver(bcm7xxx_driver); 691 692 MODULE_DEVICE_TABLE(mdio, bcm7xxx_tbl); 693 694 MODULE_DESCRIPTION("Broadcom BCM7xxx internal PHY driver"); 695 MODULE_LICENSE("GPL"); 696 MODULE_AUTHOR("Broadcom Corporation"); 697