1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Driver for Analog Devices Industrial Ethernet PHYs 4 * 5 * Copyright 2019 Analog Devices Inc. 6 */ 7 #include <linux/kernel.h> 8 #include <linux/bitfield.h> 9 #include <linux/delay.h> 10 #include <linux/errno.h> 11 #include <linux/ethtool_netlink.h> 12 #include <linux/init.h> 13 #include <linux/module.h> 14 #include <linux/mii.h> 15 #include <linux/phy.h> 16 #include <linux/property.h> 17 18 #define PHY_ID_ADIN1200 0x0283bc20 19 #define PHY_ID_ADIN1300 0x0283bc30 20 21 #define ADIN1300_MII_EXT_REG_PTR 0x0010 22 #define ADIN1300_MII_EXT_REG_DATA 0x0011 23 24 #define ADIN1300_PHY_CTRL1 0x0012 25 #define ADIN1300_AUTO_MDI_EN BIT(10) 26 #define ADIN1300_MAN_MDIX_EN BIT(9) 27 #define ADIN1300_DIAG_CLK_EN BIT(2) 28 29 #define ADIN1300_RX_ERR_CNT 0x0014 30 31 #define ADIN1300_PHY_CTRL_STATUS2 0x0015 32 #define ADIN1300_NRG_PD_EN BIT(3) 33 #define ADIN1300_NRG_PD_TX_EN BIT(2) 34 #define ADIN1300_NRG_PD_STATUS BIT(1) 35 36 #define ADIN1300_PHY_CTRL2 0x0016 37 #define ADIN1300_DOWNSPEED_AN_100_EN BIT(11) 38 #define ADIN1300_DOWNSPEED_AN_10_EN BIT(10) 39 #define ADIN1300_GROUP_MDIO_EN BIT(6) 40 #define ADIN1300_DOWNSPEEDS_EN \ 41 (ADIN1300_DOWNSPEED_AN_100_EN | ADIN1300_DOWNSPEED_AN_10_EN) 42 43 #define ADIN1300_PHY_CTRL3 0x0017 44 #define ADIN1300_LINKING_EN BIT(13) 45 #define ADIN1300_DOWNSPEED_RETRIES_MSK GENMASK(12, 10) 46 47 #define ADIN1300_INT_MASK_REG 0x0018 48 #define ADIN1300_INT_MDIO_SYNC_EN BIT(9) 49 #define ADIN1300_INT_ANEG_STAT_CHNG_EN BIT(8) 50 #define ADIN1300_INT_ANEG_PAGE_RX_EN BIT(6) 51 #define ADIN1300_INT_IDLE_ERR_CNT_EN BIT(5) 52 #define ADIN1300_INT_MAC_FIFO_OU_EN BIT(4) 53 #define ADIN1300_INT_RX_STAT_CHNG_EN BIT(3) 54 #define ADIN1300_INT_LINK_STAT_CHNG_EN BIT(2) 55 #define ADIN1300_INT_SPEED_CHNG_EN BIT(1) 56 #define ADIN1300_INT_HW_IRQ_EN BIT(0) 57 #define ADIN1300_INT_MASK_EN \ 58 (ADIN1300_INT_LINK_STAT_CHNG_EN | ADIN1300_INT_HW_IRQ_EN) 59 #define ADIN1300_INT_STATUS_REG 0x0019 60 61 #define ADIN1300_PHY_STATUS1 0x001a 62 #define ADIN1300_PAIR_01_SWAP BIT(11) 63 64 /* EEE register addresses, accessible via Clause 22 access using 65 * ADIN1300_MII_EXT_REG_PTR & ADIN1300_MII_EXT_REG_DATA. 66 * The bit-fields are the same as specified by IEEE for EEE. 67 */ 68 #define ADIN1300_EEE_CAP_REG 0x8000 69 #define ADIN1300_EEE_ADV_REG 0x8001 70 #define ADIN1300_EEE_LPABLE_REG 0x8002 71 #define ADIN1300_CLOCK_STOP_REG 0x9400 72 #define ADIN1300_LPI_WAKE_ERR_CNT_REG 0xa000 73 74 #define ADIN1300_CDIAG_RUN 0xba1b 75 #define ADIN1300_CDIAG_RUN_EN BIT(0) 76 77 /* 78 * The XSIM3/2/1 and XSHRT3/2/1 are actually relative. 79 * For CDIAG_DTLD_RSLTS(0) it's ADIN1300_CDIAG_RSLT_XSIM3/2/1 80 * For CDIAG_DTLD_RSLTS(1) it's ADIN1300_CDIAG_RSLT_XSIM3/2/0 81 * For CDIAG_DTLD_RSLTS(2) it's ADIN1300_CDIAG_RSLT_XSIM3/1/0 82 * For CDIAG_DTLD_RSLTS(3) it's ADIN1300_CDIAG_RSLT_XSIM2/1/0 83 */ 84 #define ADIN1300_CDIAG_DTLD_RSLTS(x) (0xba1d + (x)) 85 #define ADIN1300_CDIAG_RSLT_BUSY BIT(10) 86 #define ADIN1300_CDIAG_RSLT_XSIM3 BIT(9) 87 #define ADIN1300_CDIAG_RSLT_XSIM2 BIT(8) 88 #define ADIN1300_CDIAG_RSLT_XSIM1 BIT(7) 89 #define ADIN1300_CDIAG_RSLT_SIM BIT(6) 90 #define ADIN1300_CDIAG_RSLT_XSHRT3 BIT(5) 91 #define ADIN1300_CDIAG_RSLT_XSHRT2 BIT(4) 92 #define ADIN1300_CDIAG_RSLT_XSHRT1 BIT(3) 93 #define ADIN1300_CDIAG_RSLT_SHRT BIT(2) 94 #define ADIN1300_CDIAG_RSLT_OPEN BIT(1) 95 #define ADIN1300_CDIAG_RSLT_GOOD BIT(0) 96 97 #define ADIN1300_CDIAG_FLT_DIST(x) (0xba21 + (x)) 98 99 #define ADIN1300_GE_SOFT_RESET_REG 0xff0c 100 #define ADIN1300_GE_SOFT_RESET BIT(0) 101 102 #define ADIN1300_GE_CLK_CFG_REG 0xff1f 103 #define ADIN1300_GE_CLK_CFG_MASK GENMASK(5, 0) 104 #define ADIN1300_GE_CLK_CFG_RCVR_125 BIT(5) 105 #define ADIN1300_GE_CLK_CFG_FREE_125 BIT(4) 106 #define ADIN1300_GE_CLK_CFG_REF_EN BIT(3) 107 #define ADIN1300_GE_CLK_CFG_HRT_RCVR BIT(2) 108 #define ADIN1300_GE_CLK_CFG_HRT_FREE BIT(1) 109 #define ADIN1300_GE_CLK_CFG_25 BIT(0) 110 111 #define ADIN1300_GE_RGMII_CFG_REG 0xff23 112 #define ADIN1300_GE_RGMII_RX_MSK GENMASK(8, 6) 113 #define ADIN1300_GE_RGMII_RX_SEL(x) \ 114 FIELD_PREP(ADIN1300_GE_RGMII_RX_MSK, x) 115 #define ADIN1300_GE_RGMII_GTX_MSK GENMASK(5, 3) 116 #define ADIN1300_GE_RGMII_GTX_SEL(x) \ 117 FIELD_PREP(ADIN1300_GE_RGMII_GTX_MSK, x) 118 #define ADIN1300_GE_RGMII_RXID_EN BIT(2) 119 #define ADIN1300_GE_RGMII_TXID_EN BIT(1) 120 #define ADIN1300_GE_RGMII_EN BIT(0) 121 122 /* RGMII internal delay settings for rx and tx for ADIN1300 */ 123 #define ADIN1300_RGMII_1_60_NS 0x0001 124 #define ADIN1300_RGMII_1_80_NS 0x0002 125 #define ADIN1300_RGMII_2_00_NS 0x0000 126 #define ADIN1300_RGMII_2_20_NS 0x0006 127 #define ADIN1300_RGMII_2_40_NS 0x0007 128 129 #define ADIN1300_GE_RMII_CFG_REG 0xff24 130 #define ADIN1300_GE_RMII_FIFO_DEPTH_MSK GENMASK(6, 4) 131 #define ADIN1300_GE_RMII_FIFO_DEPTH_SEL(x) \ 132 FIELD_PREP(ADIN1300_GE_RMII_FIFO_DEPTH_MSK, x) 133 #define ADIN1300_GE_RMII_EN BIT(0) 134 135 /* RMII fifo depth values */ 136 #define ADIN1300_RMII_4_BITS 0x0000 137 #define ADIN1300_RMII_8_BITS 0x0001 138 #define ADIN1300_RMII_12_BITS 0x0002 139 #define ADIN1300_RMII_16_BITS 0x0003 140 #define ADIN1300_RMII_20_BITS 0x0004 141 #define ADIN1300_RMII_24_BITS 0x0005 142 143 /** 144 * struct adin_cfg_reg_map - map a config value to aregister value 145 * @cfg: value in device configuration 146 * @reg: value in the register 147 */ 148 struct adin_cfg_reg_map { 149 int cfg; 150 int reg; 151 }; 152 153 static const struct adin_cfg_reg_map adin_rgmii_delays[] = { 154 { 1600, ADIN1300_RGMII_1_60_NS }, 155 { 1800, ADIN1300_RGMII_1_80_NS }, 156 { 2000, ADIN1300_RGMII_2_00_NS }, 157 { 2200, ADIN1300_RGMII_2_20_NS }, 158 { 2400, ADIN1300_RGMII_2_40_NS }, 159 { }, 160 }; 161 162 static const struct adin_cfg_reg_map adin_rmii_fifo_depths[] = { 163 { 4, ADIN1300_RMII_4_BITS }, 164 { 8, ADIN1300_RMII_8_BITS }, 165 { 12, ADIN1300_RMII_12_BITS }, 166 { 16, ADIN1300_RMII_16_BITS }, 167 { 20, ADIN1300_RMII_20_BITS }, 168 { 24, ADIN1300_RMII_24_BITS }, 169 { }, 170 }; 171 172 /** 173 * struct adin_clause45_mmd_map - map to convert Clause 45 regs to Clause 22 174 * @devad: device address used in Clause 45 access 175 * @cl45_regnum: register address defined by Clause 45 176 * @adin_regnum: equivalent register address accessible via Clause 22 177 */ 178 struct adin_clause45_mmd_map { 179 int devad; 180 u16 cl45_regnum; 181 u16 adin_regnum; 182 }; 183 184 static const struct adin_clause45_mmd_map adin_clause45_mmd_map[] = { 185 { MDIO_MMD_PCS, MDIO_PCS_EEE_ABLE, ADIN1300_EEE_CAP_REG }, 186 { MDIO_MMD_AN, MDIO_AN_EEE_LPABLE, ADIN1300_EEE_LPABLE_REG }, 187 { MDIO_MMD_AN, MDIO_AN_EEE_ADV, ADIN1300_EEE_ADV_REG }, 188 { MDIO_MMD_PCS, MDIO_CTRL1, ADIN1300_CLOCK_STOP_REG }, 189 { MDIO_MMD_PCS, MDIO_PCS_EEE_WK_ERR, ADIN1300_LPI_WAKE_ERR_CNT_REG }, 190 }; 191 192 struct adin_hw_stat { 193 const char *string; 194 u16 reg1; 195 u16 reg2; 196 }; 197 198 static const struct adin_hw_stat adin_hw_stats[] = { 199 { "total_frames_checked_count", 0x940A, 0x940B }, /* hi + lo */ 200 { "length_error_frames_count", 0x940C }, 201 { "alignment_error_frames_count", 0x940D }, 202 { "symbol_error_count", 0x940E }, 203 { "oversized_frames_count", 0x940F }, 204 { "undersized_frames_count", 0x9410 }, 205 { "odd_nibble_frames_count", 0x9411 }, 206 { "odd_preamble_packet_count", 0x9412 }, 207 { "dribble_bits_frames_count", 0x9413 }, 208 { "false_carrier_events_count", 0x9414 }, 209 }; 210 211 /** 212 * struct adin_priv - ADIN PHY driver private data 213 * @stats: statistic counters for the PHY 214 */ 215 struct adin_priv { 216 u64 stats[ARRAY_SIZE(adin_hw_stats)]; 217 }; 218 219 static int adin_lookup_reg_value(const struct adin_cfg_reg_map *tbl, int cfg) 220 { 221 size_t i; 222 223 for (i = 0; tbl[i].cfg; i++) { 224 if (tbl[i].cfg == cfg) 225 return tbl[i].reg; 226 } 227 228 return -EINVAL; 229 } 230 231 static u32 adin_get_reg_value(struct phy_device *phydev, 232 const char *prop_name, 233 const struct adin_cfg_reg_map *tbl, 234 u32 dflt) 235 { 236 struct device *dev = &phydev->mdio.dev; 237 u32 val; 238 int rc; 239 240 if (device_property_read_u32(dev, prop_name, &val)) 241 return dflt; 242 243 rc = adin_lookup_reg_value(tbl, val); 244 if (rc < 0) { 245 phydev_warn(phydev, 246 "Unsupported value %u for %s using default (%u)\n", 247 val, prop_name, dflt); 248 return dflt; 249 } 250 251 return rc; 252 } 253 254 static int adin_config_rgmii_mode(struct phy_device *phydev) 255 { 256 u32 val; 257 int reg; 258 259 if (!phy_interface_is_rgmii(phydev)) 260 return phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, 261 ADIN1300_GE_RGMII_CFG_REG, 262 ADIN1300_GE_RGMII_EN); 263 264 reg = phy_read_mmd(phydev, MDIO_MMD_VEND1, ADIN1300_GE_RGMII_CFG_REG); 265 if (reg < 0) 266 return reg; 267 268 reg |= ADIN1300_GE_RGMII_EN; 269 270 if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID || 271 phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) { 272 reg |= ADIN1300_GE_RGMII_RXID_EN; 273 274 val = adin_get_reg_value(phydev, "adi,rx-internal-delay-ps", 275 adin_rgmii_delays, 276 ADIN1300_RGMII_2_00_NS); 277 reg &= ~ADIN1300_GE_RGMII_RX_MSK; 278 reg |= ADIN1300_GE_RGMII_RX_SEL(val); 279 } else { 280 reg &= ~ADIN1300_GE_RGMII_RXID_EN; 281 } 282 283 if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID || 284 phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) { 285 reg |= ADIN1300_GE_RGMII_TXID_EN; 286 287 val = adin_get_reg_value(phydev, "adi,tx-internal-delay-ps", 288 adin_rgmii_delays, 289 ADIN1300_RGMII_2_00_NS); 290 reg &= ~ADIN1300_GE_RGMII_GTX_MSK; 291 reg |= ADIN1300_GE_RGMII_GTX_SEL(val); 292 } else { 293 reg &= ~ADIN1300_GE_RGMII_TXID_EN; 294 } 295 296 return phy_write_mmd(phydev, MDIO_MMD_VEND1, 297 ADIN1300_GE_RGMII_CFG_REG, reg); 298 } 299 300 static int adin_config_rmii_mode(struct phy_device *phydev) 301 { 302 u32 val; 303 int reg; 304 305 if (phydev->interface != PHY_INTERFACE_MODE_RMII) 306 return phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, 307 ADIN1300_GE_RMII_CFG_REG, 308 ADIN1300_GE_RMII_EN); 309 310 reg = phy_read_mmd(phydev, MDIO_MMD_VEND1, ADIN1300_GE_RMII_CFG_REG); 311 if (reg < 0) 312 return reg; 313 314 reg |= ADIN1300_GE_RMII_EN; 315 316 val = adin_get_reg_value(phydev, "adi,fifo-depth-bits", 317 adin_rmii_fifo_depths, 318 ADIN1300_RMII_8_BITS); 319 320 reg &= ~ADIN1300_GE_RMII_FIFO_DEPTH_MSK; 321 reg |= ADIN1300_GE_RMII_FIFO_DEPTH_SEL(val); 322 323 return phy_write_mmd(phydev, MDIO_MMD_VEND1, 324 ADIN1300_GE_RMII_CFG_REG, reg); 325 } 326 327 static int adin_get_downshift(struct phy_device *phydev, u8 *data) 328 { 329 int val, cnt, enable; 330 331 val = phy_read(phydev, ADIN1300_PHY_CTRL2); 332 if (val < 0) 333 return val; 334 335 cnt = phy_read(phydev, ADIN1300_PHY_CTRL3); 336 if (cnt < 0) 337 return cnt; 338 339 enable = FIELD_GET(ADIN1300_DOWNSPEEDS_EN, val); 340 cnt = FIELD_GET(ADIN1300_DOWNSPEED_RETRIES_MSK, cnt); 341 342 *data = (enable && cnt) ? cnt : DOWNSHIFT_DEV_DISABLE; 343 344 return 0; 345 } 346 347 static int adin_set_downshift(struct phy_device *phydev, u8 cnt) 348 { 349 u16 val; 350 int rc; 351 352 if (cnt == DOWNSHIFT_DEV_DISABLE) 353 return phy_clear_bits(phydev, ADIN1300_PHY_CTRL2, 354 ADIN1300_DOWNSPEEDS_EN); 355 356 if (cnt > 7) 357 return -E2BIG; 358 359 val = FIELD_PREP(ADIN1300_DOWNSPEED_RETRIES_MSK, cnt); 360 361 rc = phy_modify(phydev, ADIN1300_PHY_CTRL3, 362 ADIN1300_DOWNSPEED_RETRIES_MSK, 363 val); 364 if (rc < 0) 365 return rc; 366 367 return phy_set_bits(phydev, ADIN1300_PHY_CTRL2, 368 ADIN1300_DOWNSPEEDS_EN); 369 } 370 371 static int adin_get_edpd(struct phy_device *phydev, u16 *tx_interval) 372 { 373 int val; 374 375 val = phy_read(phydev, ADIN1300_PHY_CTRL_STATUS2); 376 if (val < 0) 377 return val; 378 379 if (ADIN1300_NRG_PD_EN & val) { 380 if (val & ADIN1300_NRG_PD_TX_EN) 381 /* default is 1 second */ 382 *tx_interval = ETHTOOL_PHY_EDPD_DFLT_TX_MSECS; 383 else 384 *tx_interval = ETHTOOL_PHY_EDPD_NO_TX; 385 } else { 386 *tx_interval = ETHTOOL_PHY_EDPD_DISABLE; 387 } 388 389 return 0; 390 } 391 392 static int adin_set_edpd(struct phy_device *phydev, u16 tx_interval) 393 { 394 u16 val; 395 396 if (tx_interval == ETHTOOL_PHY_EDPD_DISABLE) 397 return phy_clear_bits(phydev, ADIN1300_PHY_CTRL_STATUS2, 398 (ADIN1300_NRG_PD_EN | ADIN1300_NRG_PD_TX_EN)); 399 400 val = ADIN1300_NRG_PD_EN; 401 402 switch (tx_interval) { 403 case 1000: /* 1 second */ 404 fallthrough; 405 case ETHTOOL_PHY_EDPD_DFLT_TX_MSECS: 406 val |= ADIN1300_NRG_PD_TX_EN; 407 fallthrough; 408 case ETHTOOL_PHY_EDPD_NO_TX: 409 break; 410 default: 411 return -EINVAL; 412 } 413 414 return phy_modify(phydev, ADIN1300_PHY_CTRL_STATUS2, 415 (ADIN1300_NRG_PD_EN | ADIN1300_NRG_PD_TX_EN), 416 val); 417 } 418 419 static int adin_get_tunable(struct phy_device *phydev, 420 struct ethtool_tunable *tuna, void *data) 421 { 422 switch (tuna->id) { 423 case ETHTOOL_PHY_DOWNSHIFT: 424 return adin_get_downshift(phydev, data); 425 case ETHTOOL_PHY_EDPD: 426 return adin_get_edpd(phydev, data); 427 default: 428 return -EOPNOTSUPP; 429 } 430 } 431 432 static int adin_set_tunable(struct phy_device *phydev, 433 struct ethtool_tunable *tuna, const void *data) 434 { 435 switch (tuna->id) { 436 case ETHTOOL_PHY_DOWNSHIFT: 437 return adin_set_downshift(phydev, *(const u8 *)data); 438 case ETHTOOL_PHY_EDPD: 439 return adin_set_edpd(phydev, *(const u16 *)data); 440 default: 441 return -EOPNOTSUPP; 442 } 443 } 444 445 static int adin_config_clk_out(struct phy_device *phydev) 446 { 447 struct device *dev = &phydev->mdio.dev; 448 const char *val = NULL; 449 u8 sel = 0; 450 451 device_property_read_string(dev, "adi,phy-output-clock", &val); 452 if (!val) { 453 /* property not present, do not enable GP_CLK pin */ 454 } else if (strcmp(val, "25mhz-reference") == 0) { 455 sel |= ADIN1300_GE_CLK_CFG_25; 456 } else if (strcmp(val, "125mhz-free-running") == 0) { 457 sel |= ADIN1300_GE_CLK_CFG_FREE_125; 458 } else if (strcmp(val, "adaptive-free-running") == 0) { 459 sel |= ADIN1300_GE_CLK_CFG_HRT_FREE; 460 } else { 461 phydev_err(phydev, "invalid adi,phy-output-clock\n"); 462 return -EINVAL; 463 } 464 465 if (device_property_read_bool(dev, "adi,phy-output-reference-clock")) 466 sel |= ADIN1300_GE_CLK_CFG_REF_EN; 467 468 return phy_modify_mmd(phydev, MDIO_MMD_VEND1, ADIN1300_GE_CLK_CFG_REG, 469 ADIN1300_GE_CLK_CFG_MASK, sel); 470 } 471 472 static int adin_config_init(struct phy_device *phydev) 473 { 474 int rc; 475 476 phydev->mdix_ctrl = ETH_TP_MDI_AUTO; 477 478 rc = adin_config_rgmii_mode(phydev); 479 if (rc < 0) 480 return rc; 481 482 rc = adin_config_rmii_mode(phydev); 483 if (rc < 0) 484 return rc; 485 486 rc = adin_set_downshift(phydev, 4); 487 if (rc < 0) 488 return rc; 489 490 rc = adin_set_edpd(phydev, ETHTOOL_PHY_EDPD_DFLT_TX_MSECS); 491 if (rc < 0) 492 return rc; 493 494 rc = adin_config_clk_out(phydev); 495 if (rc < 0) 496 return rc; 497 498 phydev_dbg(phydev, "PHY is using mode '%s'\n", 499 phy_modes(phydev->interface)); 500 501 return 0; 502 } 503 504 static int adin_phy_ack_intr(struct phy_device *phydev) 505 { 506 /* Clear pending interrupts */ 507 int rc = phy_read(phydev, ADIN1300_INT_STATUS_REG); 508 509 return rc < 0 ? rc : 0; 510 } 511 512 static int adin_phy_config_intr(struct phy_device *phydev) 513 { 514 int err; 515 516 if (phydev->interrupts == PHY_INTERRUPT_ENABLED) { 517 err = adin_phy_ack_intr(phydev); 518 if (err) 519 return err; 520 521 err = phy_set_bits(phydev, ADIN1300_INT_MASK_REG, 522 ADIN1300_INT_MASK_EN); 523 } else { 524 err = phy_clear_bits(phydev, ADIN1300_INT_MASK_REG, 525 ADIN1300_INT_MASK_EN); 526 if (err) 527 return err; 528 529 err = adin_phy_ack_intr(phydev); 530 } 531 532 return err; 533 } 534 535 static irqreturn_t adin_phy_handle_interrupt(struct phy_device *phydev) 536 { 537 int irq_status; 538 539 irq_status = phy_read(phydev, ADIN1300_INT_STATUS_REG); 540 if (irq_status < 0) { 541 phy_error(phydev); 542 return IRQ_NONE; 543 } 544 545 if (!(irq_status & ADIN1300_INT_LINK_STAT_CHNG_EN)) 546 return IRQ_NONE; 547 548 phy_trigger_machine(phydev); 549 550 return IRQ_HANDLED; 551 } 552 553 static int adin_cl45_to_adin_reg(struct phy_device *phydev, int devad, 554 u16 cl45_regnum) 555 { 556 const struct adin_clause45_mmd_map *m; 557 int i; 558 559 if (devad == MDIO_MMD_VEND1) 560 return cl45_regnum; 561 562 for (i = 0; i < ARRAY_SIZE(adin_clause45_mmd_map); i++) { 563 m = &adin_clause45_mmd_map[i]; 564 if (m->devad == devad && m->cl45_regnum == cl45_regnum) 565 return m->adin_regnum; 566 } 567 568 phydev_err(phydev, 569 "No translation available for devad: %d reg: %04x\n", 570 devad, cl45_regnum); 571 572 return -EINVAL; 573 } 574 575 static int adin_read_mmd(struct phy_device *phydev, int devad, u16 regnum) 576 { 577 struct mii_bus *bus = phydev->mdio.bus; 578 int phy_addr = phydev->mdio.addr; 579 int adin_regnum; 580 int err; 581 582 adin_regnum = adin_cl45_to_adin_reg(phydev, devad, regnum); 583 if (adin_regnum < 0) 584 return adin_regnum; 585 586 err = __mdiobus_write(bus, phy_addr, ADIN1300_MII_EXT_REG_PTR, 587 adin_regnum); 588 if (err) 589 return err; 590 591 return __mdiobus_read(bus, phy_addr, ADIN1300_MII_EXT_REG_DATA); 592 } 593 594 static int adin_write_mmd(struct phy_device *phydev, int devad, u16 regnum, 595 u16 val) 596 { 597 struct mii_bus *bus = phydev->mdio.bus; 598 int phy_addr = phydev->mdio.addr; 599 int adin_regnum; 600 int err; 601 602 adin_regnum = adin_cl45_to_adin_reg(phydev, devad, regnum); 603 if (adin_regnum < 0) 604 return adin_regnum; 605 606 err = __mdiobus_write(bus, phy_addr, ADIN1300_MII_EXT_REG_PTR, 607 adin_regnum); 608 if (err) 609 return err; 610 611 return __mdiobus_write(bus, phy_addr, ADIN1300_MII_EXT_REG_DATA, val); 612 } 613 614 static int adin_config_mdix(struct phy_device *phydev) 615 { 616 bool auto_en, mdix_en; 617 int reg; 618 619 mdix_en = false; 620 auto_en = false; 621 switch (phydev->mdix_ctrl) { 622 case ETH_TP_MDI: 623 break; 624 case ETH_TP_MDI_X: 625 mdix_en = true; 626 break; 627 case ETH_TP_MDI_AUTO: 628 auto_en = true; 629 break; 630 default: 631 return -EINVAL; 632 } 633 634 reg = phy_read(phydev, ADIN1300_PHY_CTRL1); 635 if (reg < 0) 636 return reg; 637 638 if (mdix_en) 639 reg |= ADIN1300_MAN_MDIX_EN; 640 else 641 reg &= ~ADIN1300_MAN_MDIX_EN; 642 643 if (auto_en) 644 reg |= ADIN1300_AUTO_MDI_EN; 645 else 646 reg &= ~ADIN1300_AUTO_MDI_EN; 647 648 return phy_write(phydev, ADIN1300_PHY_CTRL1, reg); 649 } 650 651 static int adin_config_aneg(struct phy_device *phydev) 652 { 653 int ret; 654 655 ret = phy_clear_bits(phydev, ADIN1300_PHY_CTRL1, ADIN1300_DIAG_CLK_EN); 656 if (ret < 0) 657 return ret; 658 659 ret = phy_set_bits(phydev, ADIN1300_PHY_CTRL3, ADIN1300_LINKING_EN); 660 if (ret < 0) 661 return ret; 662 663 ret = adin_config_mdix(phydev); 664 if (ret) 665 return ret; 666 667 return genphy_config_aneg(phydev); 668 } 669 670 static int adin_mdix_update(struct phy_device *phydev) 671 { 672 bool auto_en, mdix_en; 673 bool swapped; 674 int reg; 675 676 reg = phy_read(phydev, ADIN1300_PHY_CTRL1); 677 if (reg < 0) 678 return reg; 679 680 auto_en = !!(reg & ADIN1300_AUTO_MDI_EN); 681 mdix_en = !!(reg & ADIN1300_MAN_MDIX_EN); 682 683 /* If MDI/MDIX is forced, just read it from the control reg */ 684 if (!auto_en) { 685 if (mdix_en) 686 phydev->mdix = ETH_TP_MDI_X; 687 else 688 phydev->mdix = ETH_TP_MDI; 689 return 0; 690 } 691 692 /** 693 * Otherwise, we need to deduce it from the PHY status2 reg. 694 * When Auto-MDI is enabled, the ADIN1300_MAN_MDIX_EN bit implies 695 * a preference for MDIX when it is set. 696 */ 697 reg = phy_read(phydev, ADIN1300_PHY_STATUS1); 698 if (reg < 0) 699 return reg; 700 701 swapped = !!(reg & ADIN1300_PAIR_01_SWAP); 702 703 if (mdix_en != swapped) 704 phydev->mdix = ETH_TP_MDI_X; 705 else 706 phydev->mdix = ETH_TP_MDI; 707 708 return 0; 709 } 710 711 static int adin_read_status(struct phy_device *phydev) 712 { 713 int ret; 714 715 ret = adin_mdix_update(phydev); 716 if (ret < 0) 717 return ret; 718 719 return genphy_read_status(phydev); 720 } 721 722 static int adin_soft_reset(struct phy_device *phydev) 723 { 724 int rc; 725 726 /* The reset bit is self-clearing, set it and wait */ 727 rc = phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, 728 ADIN1300_GE_SOFT_RESET_REG, 729 ADIN1300_GE_SOFT_RESET); 730 if (rc < 0) 731 return rc; 732 733 msleep(20); 734 735 /* If we get a read error something may be wrong */ 736 rc = phy_read_mmd(phydev, MDIO_MMD_VEND1, 737 ADIN1300_GE_SOFT_RESET_REG); 738 739 return rc < 0 ? rc : 0; 740 } 741 742 static int adin_get_sset_count(struct phy_device *phydev) 743 { 744 return ARRAY_SIZE(adin_hw_stats); 745 } 746 747 static void adin_get_strings(struct phy_device *phydev, u8 *data) 748 { 749 int i; 750 751 for (i = 0; i < ARRAY_SIZE(adin_hw_stats); i++) { 752 strlcpy(&data[i * ETH_GSTRING_LEN], 753 adin_hw_stats[i].string, ETH_GSTRING_LEN); 754 } 755 } 756 757 static int adin_read_mmd_stat_regs(struct phy_device *phydev, 758 const struct adin_hw_stat *stat, 759 u32 *val) 760 { 761 int ret; 762 763 ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, stat->reg1); 764 if (ret < 0) 765 return ret; 766 767 *val = (ret & 0xffff); 768 769 if (stat->reg2 == 0) 770 return 0; 771 772 ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, stat->reg2); 773 if (ret < 0) 774 return ret; 775 776 *val <<= 16; 777 *val |= (ret & 0xffff); 778 779 return 0; 780 } 781 782 static u64 adin_get_stat(struct phy_device *phydev, int i) 783 { 784 const struct adin_hw_stat *stat = &adin_hw_stats[i]; 785 struct adin_priv *priv = phydev->priv; 786 u32 val; 787 int ret; 788 789 if (stat->reg1 > 0x1f) { 790 ret = adin_read_mmd_stat_regs(phydev, stat, &val); 791 if (ret < 0) 792 return (u64)(~0); 793 } else { 794 ret = phy_read(phydev, stat->reg1); 795 if (ret < 0) 796 return (u64)(~0); 797 val = (ret & 0xffff); 798 } 799 800 priv->stats[i] += val; 801 802 return priv->stats[i]; 803 } 804 805 static void adin_get_stats(struct phy_device *phydev, 806 struct ethtool_stats *stats, u64 *data) 807 { 808 int i, rc; 809 810 /* latch copies of all the frame-checker counters */ 811 rc = phy_read(phydev, ADIN1300_RX_ERR_CNT); 812 if (rc < 0) 813 return; 814 815 for (i = 0; i < ARRAY_SIZE(adin_hw_stats); i++) 816 data[i] = adin_get_stat(phydev, i); 817 } 818 819 static int adin_probe(struct phy_device *phydev) 820 { 821 struct device *dev = &phydev->mdio.dev; 822 struct adin_priv *priv; 823 824 priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); 825 if (!priv) 826 return -ENOMEM; 827 828 phydev->priv = priv; 829 830 return 0; 831 } 832 833 static int adin_cable_test_start(struct phy_device *phydev) 834 { 835 int ret; 836 837 ret = phy_clear_bits(phydev, ADIN1300_PHY_CTRL3, ADIN1300_LINKING_EN); 838 if (ret < 0) 839 return ret; 840 841 ret = phy_clear_bits(phydev, ADIN1300_PHY_CTRL1, ADIN1300_DIAG_CLK_EN); 842 if (ret < 0) 843 return ret; 844 845 /* wait a bit for the clock to stabilize */ 846 msleep(50); 847 848 return phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, ADIN1300_CDIAG_RUN, 849 ADIN1300_CDIAG_RUN_EN); 850 } 851 852 static int adin_cable_test_report_trans(int result) 853 { 854 int mask; 855 856 if (result & ADIN1300_CDIAG_RSLT_GOOD) 857 return ETHTOOL_A_CABLE_RESULT_CODE_OK; 858 if (result & ADIN1300_CDIAG_RSLT_OPEN) 859 return ETHTOOL_A_CABLE_RESULT_CODE_OPEN; 860 861 /* short with other pairs */ 862 mask = ADIN1300_CDIAG_RSLT_XSHRT3 | 863 ADIN1300_CDIAG_RSLT_XSHRT2 | 864 ADIN1300_CDIAG_RSLT_XSHRT1; 865 if (result & mask) 866 return ETHTOOL_A_CABLE_RESULT_CODE_CROSS_SHORT; 867 868 if (result & ADIN1300_CDIAG_RSLT_SHRT) 869 return ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT; 870 871 return ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC; 872 } 873 874 static int adin_cable_test_report_pair(struct phy_device *phydev, 875 unsigned int pair) 876 { 877 int fault_rslt; 878 int ret; 879 880 ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, 881 ADIN1300_CDIAG_DTLD_RSLTS(pair)); 882 if (ret < 0) 883 return ret; 884 885 fault_rslt = adin_cable_test_report_trans(ret); 886 887 ret = ethnl_cable_test_result(phydev, pair, fault_rslt); 888 if (ret < 0) 889 return ret; 890 891 ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, 892 ADIN1300_CDIAG_FLT_DIST(pair)); 893 if (ret < 0) 894 return ret; 895 896 switch (fault_rslt) { 897 case ETHTOOL_A_CABLE_RESULT_CODE_OPEN: 898 case ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT: 899 case ETHTOOL_A_CABLE_RESULT_CODE_CROSS_SHORT: 900 return ethnl_cable_test_fault_length(phydev, pair, ret * 100); 901 default: 902 return 0; 903 } 904 } 905 906 static int adin_cable_test_report(struct phy_device *phydev) 907 { 908 unsigned int pair; 909 int ret; 910 911 for (pair = ETHTOOL_A_CABLE_PAIR_A; pair <= ETHTOOL_A_CABLE_PAIR_D; pair++) { 912 ret = adin_cable_test_report_pair(phydev, pair); 913 if (ret < 0) 914 return ret; 915 } 916 917 return 0; 918 } 919 920 static int adin_cable_test_get_status(struct phy_device *phydev, 921 bool *finished) 922 { 923 int ret; 924 925 *finished = false; 926 927 ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, ADIN1300_CDIAG_RUN); 928 if (ret < 0) 929 return ret; 930 931 if (ret & ADIN1300_CDIAG_RUN_EN) 932 return 0; 933 934 *finished = true; 935 936 return adin_cable_test_report(phydev); 937 } 938 939 static struct phy_driver adin_driver[] = { 940 { 941 PHY_ID_MATCH_MODEL(PHY_ID_ADIN1200), 942 .name = "ADIN1200", 943 .flags = PHY_POLL_CABLE_TEST, 944 .probe = adin_probe, 945 .config_init = adin_config_init, 946 .soft_reset = adin_soft_reset, 947 .config_aneg = adin_config_aneg, 948 .read_status = adin_read_status, 949 .get_tunable = adin_get_tunable, 950 .set_tunable = adin_set_tunable, 951 .config_intr = adin_phy_config_intr, 952 .handle_interrupt = adin_phy_handle_interrupt, 953 .get_sset_count = adin_get_sset_count, 954 .get_strings = adin_get_strings, 955 .get_stats = adin_get_stats, 956 .resume = genphy_resume, 957 .suspend = genphy_suspend, 958 .read_mmd = adin_read_mmd, 959 .write_mmd = adin_write_mmd, 960 .cable_test_start = adin_cable_test_start, 961 .cable_test_get_status = adin_cable_test_get_status, 962 }, 963 { 964 PHY_ID_MATCH_MODEL(PHY_ID_ADIN1300), 965 .name = "ADIN1300", 966 .flags = PHY_POLL_CABLE_TEST, 967 .probe = adin_probe, 968 .config_init = adin_config_init, 969 .soft_reset = adin_soft_reset, 970 .config_aneg = adin_config_aneg, 971 .read_status = adin_read_status, 972 .get_tunable = adin_get_tunable, 973 .set_tunable = adin_set_tunable, 974 .config_intr = adin_phy_config_intr, 975 .handle_interrupt = adin_phy_handle_interrupt, 976 .get_sset_count = adin_get_sset_count, 977 .get_strings = adin_get_strings, 978 .get_stats = adin_get_stats, 979 .resume = genphy_resume, 980 .suspend = genphy_suspend, 981 .read_mmd = adin_read_mmd, 982 .write_mmd = adin_write_mmd, 983 .cable_test_start = adin_cable_test_start, 984 .cable_test_get_status = adin_cable_test_get_status, 985 }, 986 }; 987 988 module_phy_driver(adin_driver); 989 990 static struct mdio_device_id __maybe_unused adin_tbl[] = { 991 { PHY_ID_MATCH_MODEL(PHY_ID_ADIN1200) }, 992 { PHY_ID_MATCH_MODEL(PHY_ID_ADIN1300) }, 993 { } 994 }; 995 996 MODULE_DEVICE_TABLE(mdio, adin_tbl); 997 MODULE_DESCRIPTION("Analog Devices Industrial Ethernet PHY driver"); 998 MODULE_LICENSE("GPL"); 999