1 // SPDX-License-Identifier: GPL-2.0
2 /*
3 * Copyright (C) 2022 Schneider Electric
4 *
5 * Clément Léger <clement.leger@bootlin.com>
6 */
7
8 #include <linux/clk.h>
9 #include <linux/device.h>
10 #include <linux/mdio.h>
11 #include <linux/of.h>
12 #include <linux/of_platform.h>
13 #include <linux/pcs-rzn1-miic.h>
14 #include <linux/phylink.h>
15 #include <linux/platform_device.h>
16 #include <linux/pm_runtime.h>
17 #include <dt-bindings/net/pcs-rzn1-miic.h>
18
19 #define MIIC_PRCMD 0x0
20 #define MIIC_ESID_CODE 0x4
21
22 #define MIIC_MODCTRL 0x20
23 #define MIIC_MODCTRL_SW_MODE GENMASK(4, 0)
24
25 #define MIIC_CONVCTRL(port) (0x100 + (port) * 4)
26
27 #define MIIC_CONVCTRL_CONV_SPEED GENMASK(1, 0)
28 #define CONV_MODE_10MBPS 0
29 #define CONV_MODE_100MBPS 1
30 #define CONV_MODE_1000MBPS 2
31
32 #define MIIC_CONVCTRL_CONV_MODE GENMASK(3, 2)
33 #define CONV_MODE_MII 0
34 #define CONV_MODE_RMII 1
35 #define CONV_MODE_RGMII 2
36
37 #define MIIC_CONVCTRL_FULLD BIT(8)
38 #define MIIC_CONVCTRL_RGMII_LINK BIT(12)
39 #define MIIC_CONVCTRL_RGMII_DUPLEX BIT(13)
40 #define MIIC_CONVCTRL_RGMII_SPEED GENMASK(15, 14)
41
42 #define MIIC_CONVRST 0x114
43 #define MIIC_CONVRST_PHYIF_RST(port) BIT(port)
44 #define MIIC_CONVRST_PHYIF_RST_MASK GENMASK(4, 0)
45
46 #define MIIC_SWCTRL 0x304
47 #define MIIC_SWDUPC 0x308
48
49 #define MIIC_MAX_NR_PORTS 5
50
51 #define MIIC_MODCTRL_CONF_CONV_NUM 6
52 #define MIIC_MODCTRL_CONF_NONE -1
53
54 /**
55 * struct modctrl_match - Matching table entry for convctrl configuration
56 * See section 8.2.1 of manual.
57 * @mode_cfg: Configuration value for convctrl
58 * @conv: Configuration of ethernet port muxes. First index is SWITCH_PORTIN,
59 * then index 1 - 5 are CONV1 - CONV5.
60 */
61 struct modctrl_match {
62 u32 mode_cfg;
63 u8 conv[MIIC_MODCTRL_CONF_CONV_NUM];
64 };
65
66 static struct modctrl_match modctrl_match_table[] = {
67 {0x0, {MIIC_RTOS_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD,
68 MIIC_SWITCH_PORTC, MIIC_SERCOS_PORTB, MIIC_SERCOS_PORTA}},
69 {0x1, {MIIC_RTOS_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD,
70 MIIC_SWITCH_PORTC, MIIC_ETHERCAT_PORTB, MIIC_ETHERCAT_PORTA}},
71 {0x2, {MIIC_RTOS_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD,
72 MIIC_ETHERCAT_PORTC, MIIC_ETHERCAT_PORTB, MIIC_ETHERCAT_PORTA}},
73 {0x3, {MIIC_RTOS_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD,
74 MIIC_SWITCH_PORTC, MIIC_SWITCH_PORTB, MIIC_SWITCH_PORTA}},
75
76 {0x8, {MIIC_RTOS_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD,
77 MIIC_SWITCH_PORTC, MIIC_SERCOS_PORTB, MIIC_SERCOS_PORTA}},
78 {0x9, {MIIC_RTOS_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD,
79 MIIC_SWITCH_PORTC, MIIC_ETHERCAT_PORTB, MIIC_ETHERCAT_PORTA}},
80 {0xA, {MIIC_RTOS_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD,
81 MIIC_ETHERCAT_PORTC, MIIC_ETHERCAT_PORTB, MIIC_ETHERCAT_PORTA}},
82 {0xB, {MIIC_RTOS_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD,
83 MIIC_SWITCH_PORTC, MIIC_SWITCH_PORTB, MIIC_SWITCH_PORTA}},
84
85 {0x10, {MIIC_GMAC2_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD,
86 MIIC_SWITCH_PORTC, MIIC_SERCOS_PORTB, MIIC_SERCOS_PORTA}},
87 {0x11, {MIIC_GMAC2_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD,
88 MIIC_SWITCH_PORTC, MIIC_ETHERCAT_PORTB, MIIC_ETHERCAT_PORTA}},
89 {0x12, {MIIC_GMAC2_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD,
90 MIIC_ETHERCAT_PORTC, MIIC_ETHERCAT_PORTB, MIIC_ETHERCAT_PORTA}},
91 {0x13, {MIIC_GMAC2_PORT, MIIC_GMAC1_PORT, MIIC_SWITCH_PORTD,
92 MIIC_SWITCH_PORTC, MIIC_SWITCH_PORTB, MIIC_SWITCH_PORTA}}
93 };
94
95 static const char * const conf_to_string[] = {
96 [MIIC_GMAC1_PORT] = "GMAC1_PORT",
97 [MIIC_GMAC2_PORT] = "GMAC2_PORT",
98 [MIIC_RTOS_PORT] = "RTOS_PORT",
99 [MIIC_SERCOS_PORTA] = "SERCOS_PORTA",
100 [MIIC_SERCOS_PORTB] = "SERCOS_PORTB",
101 [MIIC_ETHERCAT_PORTA] = "ETHERCAT_PORTA",
102 [MIIC_ETHERCAT_PORTB] = "ETHERCAT_PORTB",
103 [MIIC_ETHERCAT_PORTC] = "ETHERCAT_PORTC",
104 [MIIC_SWITCH_PORTA] = "SWITCH_PORTA",
105 [MIIC_SWITCH_PORTB] = "SWITCH_PORTB",
106 [MIIC_SWITCH_PORTC] = "SWITCH_PORTC",
107 [MIIC_SWITCH_PORTD] = "SWITCH_PORTD",
108 [MIIC_HSR_PORTA] = "HSR_PORTA",
109 [MIIC_HSR_PORTB] = "HSR_PORTB",
110 };
111
112 static const char *index_to_string[MIIC_MODCTRL_CONF_CONV_NUM] = {
113 "SWITCH_PORTIN",
114 "CONV1",
115 "CONV2",
116 "CONV3",
117 "CONV4",
118 "CONV5",
119 };
120
121 /**
122 * struct miic - MII converter structure
123 * @base: base address of the MII converter
124 * @dev: Device associated to the MII converter
125 * @lock: Lock used for read-modify-write access
126 */
127 struct miic {
128 void __iomem *base;
129 struct device *dev;
130 spinlock_t lock;
131 };
132
133 /**
134 * struct miic_port - Per port MII converter struct
135 * @miic: backiling to MII converter structure
136 * @pcs: PCS structure associated to the port
137 * @port: port number
138 * @interface: interface mode of the port
139 */
140 struct miic_port {
141 struct miic *miic;
142 struct phylink_pcs pcs;
143 int port;
144 phy_interface_t interface;
145 };
146
phylink_pcs_to_miic_port(struct phylink_pcs * pcs)147 static struct miic_port *phylink_pcs_to_miic_port(struct phylink_pcs *pcs)
148 {
149 return container_of(pcs, struct miic_port, pcs);
150 }
151
miic_reg_writel(struct miic * miic,int offset,u32 value)152 static void miic_reg_writel(struct miic *miic, int offset, u32 value)
153 {
154 writel(value, miic->base + offset);
155 }
156
miic_reg_readl(struct miic * miic,int offset)157 static u32 miic_reg_readl(struct miic *miic, int offset)
158 {
159 return readl(miic->base + offset);
160 }
161
miic_reg_rmw(struct miic * miic,int offset,u32 mask,u32 val)162 static void miic_reg_rmw(struct miic *miic, int offset, u32 mask, u32 val)
163 {
164 u32 reg;
165
166 spin_lock(&miic->lock);
167
168 reg = miic_reg_readl(miic, offset);
169 reg &= ~mask;
170 reg |= val;
171 miic_reg_writel(miic, offset, reg);
172
173 spin_unlock(&miic->lock);
174 }
175
miic_converter_enable(struct miic * miic,int port,int enable)176 static void miic_converter_enable(struct miic *miic, int port, int enable)
177 {
178 u32 val = 0;
179
180 if (enable)
181 val = MIIC_CONVRST_PHYIF_RST(port);
182
183 miic_reg_rmw(miic, MIIC_CONVRST, MIIC_CONVRST_PHYIF_RST(port), val);
184 }
185
miic_config(struct phylink_pcs * pcs,unsigned int mode,phy_interface_t interface,const unsigned long * advertising,bool permit)186 static int miic_config(struct phylink_pcs *pcs, unsigned int mode,
187 phy_interface_t interface,
188 const unsigned long *advertising, bool permit)
189 {
190 struct miic_port *miic_port = phylink_pcs_to_miic_port(pcs);
191 struct miic *miic = miic_port->miic;
192 u32 speed, conv_mode, val, mask;
193 int port = miic_port->port;
194
195 switch (interface) {
196 case PHY_INTERFACE_MODE_RMII:
197 conv_mode = CONV_MODE_RMII;
198 speed = CONV_MODE_100MBPS;
199 break;
200 case PHY_INTERFACE_MODE_RGMII:
201 case PHY_INTERFACE_MODE_RGMII_ID:
202 case PHY_INTERFACE_MODE_RGMII_TXID:
203 case PHY_INTERFACE_MODE_RGMII_RXID:
204 conv_mode = CONV_MODE_RGMII;
205 speed = CONV_MODE_1000MBPS;
206 break;
207 case PHY_INTERFACE_MODE_MII:
208 conv_mode = CONV_MODE_MII;
209 /* When in MII mode, speed should be set to 0 (which is actually
210 * CONV_MODE_10MBPS)
211 */
212 speed = CONV_MODE_10MBPS;
213 break;
214 default:
215 return -EOPNOTSUPP;
216 }
217
218 val = FIELD_PREP(MIIC_CONVCTRL_CONV_MODE, conv_mode);
219 mask = MIIC_CONVCTRL_CONV_MODE;
220
221 /* Update speed only if we are going to change the interface because
222 * the link might already be up and it would break it if the speed is
223 * changed.
224 */
225 if (interface != miic_port->interface) {
226 val |= FIELD_PREP(MIIC_CONVCTRL_CONV_SPEED, speed);
227 mask |= MIIC_CONVCTRL_CONV_SPEED;
228 miic_port->interface = interface;
229 }
230
231 miic_reg_rmw(miic, MIIC_CONVCTRL(port), mask, val);
232 miic_converter_enable(miic, miic_port->port, 1);
233
234 return 0;
235 }
236
miic_link_up(struct phylink_pcs * pcs,unsigned int mode,phy_interface_t interface,int speed,int duplex)237 static void miic_link_up(struct phylink_pcs *pcs, unsigned int mode,
238 phy_interface_t interface, int speed, int duplex)
239 {
240 struct miic_port *miic_port = phylink_pcs_to_miic_port(pcs);
241 struct miic *miic = miic_port->miic;
242 u32 conv_speed = 0, val = 0;
243 int port = miic_port->port;
244
245 if (duplex == DUPLEX_FULL)
246 val |= MIIC_CONVCTRL_FULLD;
247
248 /* No speed in MII through-mode */
249 if (interface != PHY_INTERFACE_MODE_MII) {
250 switch (speed) {
251 case SPEED_1000:
252 conv_speed = CONV_MODE_1000MBPS;
253 break;
254 case SPEED_100:
255 conv_speed = CONV_MODE_100MBPS;
256 break;
257 case SPEED_10:
258 conv_speed = CONV_MODE_10MBPS;
259 break;
260 default:
261 return;
262 }
263 }
264
265 val |= FIELD_PREP(MIIC_CONVCTRL_CONV_SPEED, conv_speed);
266
267 miic_reg_rmw(miic, MIIC_CONVCTRL(port),
268 (MIIC_CONVCTRL_CONV_SPEED | MIIC_CONVCTRL_FULLD), val);
269 }
270
miic_validate(struct phylink_pcs * pcs,unsigned long * supported,const struct phylink_link_state * state)271 static int miic_validate(struct phylink_pcs *pcs, unsigned long *supported,
272 const struct phylink_link_state *state)
273 {
274 if (phy_interface_mode_is_rgmii(state->interface) ||
275 state->interface == PHY_INTERFACE_MODE_RMII ||
276 state->interface == PHY_INTERFACE_MODE_MII)
277 return 1;
278
279 return -EINVAL;
280 }
281
282 static const struct phylink_pcs_ops miic_phylink_ops = {
283 .pcs_validate = miic_validate,
284 .pcs_config = miic_config,
285 .pcs_link_up = miic_link_up,
286 };
287
miic_create(struct device * dev,struct device_node * np)288 struct phylink_pcs *miic_create(struct device *dev, struct device_node *np)
289 {
290 struct platform_device *pdev;
291 struct miic_port *miic_port;
292 struct device_node *pcs_np;
293 struct miic *miic;
294 u32 port;
295
296 if (!of_device_is_available(np))
297 return ERR_PTR(-ENODEV);
298
299 if (of_property_read_u32(np, "reg", &port))
300 return ERR_PTR(-EINVAL);
301
302 if (port > MIIC_MAX_NR_PORTS || port < 1)
303 return ERR_PTR(-EINVAL);
304
305 /* The PCS pdev is attached to the parent node */
306 pcs_np = of_get_parent(np);
307 if (!pcs_np)
308 return ERR_PTR(-ENODEV);
309
310 if (!of_device_is_available(pcs_np)) {
311 of_node_put(pcs_np);
312 return ERR_PTR(-ENODEV);
313 }
314
315 pdev = of_find_device_by_node(pcs_np);
316 of_node_put(pcs_np);
317 if (!pdev || !platform_get_drvdata(pdev)) {
318 if (pdev)
319 put_device(&pdev->dev);
320 return ERR_PTR(-EPROBE_DEFER);
321 }
322
323 miic_port = kzalloc(sizeof(*miic_port), GFP_KERNEL);
324 if (!miic_port) {
325 put_device(&pdev->dev);
326 return ERR_PTR(-ENOMEM);
327 }
328
329 miic = platform_get_drvdata(pdev);
330 device_link_add(dev, miic->dev, DL_FLAG_AUTOREMOVE_CONSUMER);
331 put_device(&pdev->dev);
332
333 miic_port->miic = miic;
334 miic_port->port = port - 1;
335 miic_port->pcs.ops = &miic_phylink_ops;
336
337 return &miic_port->pcs;
338 }
339 EXPORT_SYMBOL(miic_create);
340
miic_destroy(struct phylink_pcs * pcs)341 void miic_destroy(struct phylink_pcs *pcs)
342 {
343 struct miic_port *miic_port = phylink_pcs_to_miic_port(pcs);
344
345 miic_converter_enable(miic_port->miic, miic_port->port, 0);
346 kfree(miic_port);
347 }
348 EXPORT_SYMBOL(miic_destroy);
349
miic_init_hw(struct miic * miic,u32 cfg_mode)350 static int miic_init_hw(struct miic *miic, u32 cfg_mode)
351 {
352 int port;
353
354 /* Unlock write access to accessory registers (cf datasheet). If this
355 * is going to be used in conjunction with the Cortex-M3, this sequence
356 * will have to be moved in register write
357 */
358 miic_reg_writel(miic, MIIC_PRCMD, 0x00A5);
359 miic_reg_writel(miic, MIIC_PRCMD, 0x0001);
360 miic_reg_writel(miic, MIIC_PRCMD, 0xFFFE);
361 miic_reg_writel(miic, MIIC_PRCMD, 0x0001);
362
363 miic_reg_writel(miic, MIIC_MODCTRL,
364 FIELD_PREP(MIIC_MODCTRL_SW_MODE, cfg_mode));
365
366 for (port = 0; port < MIIC_MAX_NR_PORTS; port++) {
367 miic_converter_enable(miic, port, 0);
368 /* Disable speed/duplex control from these registers, datasheet
369 * says switch registers should be used to setup switch port
370 * speed and duplex.
371 */
372 miic_reg_writel(miic, MIIC_SWCTRL, 0x0);
373 miic_reg_writel(miic, MIIC_SWDUPC, 0x0);
374 }
375
376 return 0;
377 }
378
miic_modctrl_match(s8 table_val[MIIC_MODCTRL_CONF_CONV_NUM],s8 dt_val[MIIC_MODCTRL_CONF_CONV_NUM])379 static bool miic_modctrl_match(s8 table_val[MIIC_MODCTRL_CONF_CONV_NUM],
380 s8 dt_val[MIIC_MODCTRL_CONF_CONV_NUM])
381 {
382 int i;
383
384 for (i = 0; i < MIIC_MODCTRL_CONF_CONV_NUM; i++) {
385 if (dt_val[i] == MIIC_MODCTRL_CONF_NONE)
386 continue;
387
388 if (dt_val[i] != table_val[i])
389 return false;
390 }
391
392 return true;
393 }
394
miic_dump_conf(struct device * dev,s8 conf[MIIC_MODCTRL_CONF_CONV_NUM])395 static void miic_dump_conf(struct device *dev,
396 s8 conf[MIIC_MODCTRL_CONF_CONV_NUM])
397 {
398 const char *conf_name;
399 int i;
400
401 for (i = 0; i < MIIC_MODCTRL_CONF_CONV_NUM; i++) {
402 if (conf[i] != MIIC_MODCTRL_CONF_NONE)
403 conf_name = conf_to_string[conf[i]];
404 else
405 conf_name = "NONE";
406
407 dev_err(dev, "%s: %s\n", index_to_string[i], conf_name);
408 }
409 }
410
miic_match_dt_conf(struct device * dev,s8 dt_val[MIIC_MODCTRL_CONF_CONV_NUM],u32 * mode_cfg)411 static int miic_match_dt_conf(struct device *dev,
412 s8 dt_val[MIIC_MODCTRL_CONF_CONV_NUM],
413 u32 *mode_cfg)
414 {
415 struct modctrl_match *table_entry;
416 int i;
417
418 for (i = 0; i < ARRAY_SIZE(modctrl_match_table); i++) {
419 table_entry = &modctrl_match_table[i];
420
421 if (miic_modctrl_match(table_entry->conv, dt_val)) {
422 *mode_cfg = table_entry->mode_cfg;
423 return 0;
424 }
425 }
426
427 dev_err(dev, "Failed to apply requested configuration\n");
428 miic_dump_conf(dev, dt_val);
429
430 return -EINVAL;
431 }
432
miic_parse_dt(struct device * dev,u32 * mode_cfg)433 static int miic_parse_dt(struct device *dev, u32 *mode_cfg)
434 {
435 s8 dt_val[MIIC_MODCTRL_CONF_CONV_NUM];
436 struct device_node *np = dev->of_node;
437 struct device_node *conv;
438 u32 conf;
439 int port;
440
441 memset(dt_val, MIIC_MODCTRL_CONF_NONE, sizeof(dt_val));
442
443 if (of_property_read_u32(np, "renesas,miic-switch-portin", &conf) == 0)
444 dt_val[0] = conf;
445
446 for_each_child_of_node(np, conv) {
447 if (of_property_read_u32(conv, "reg", &port))
448 continue;
449
450 if (!of_device_is_available(conv))
451 continue;
452
453 if (of_property_read_u32(conv, "renesas,miic-input", &conf) == 0)
454 dt_val[port] = conf;
455 }
456
457 return miic_match_dt_conf(dev, dt_val, mode_cfg);
458 }
459
miic_probe(struct platform_device * pdev)460 static int miic_probe(struct platform_device *pdev)
461 {
462 struct device *dev = &pdev->dev;
463 struct miic *miic;
464 u32 mode_cfg;
465 int ret;
466
467 ret = miic_parse_dt(dev, &mode_cfg);
468 if (ret < 0)
469 return ret;
470
471 miic = devm_kzalloc(dev, sizeof(*miic), GFP_KERNEL);
472 if (!miic)
473 return -ENOMEM;
474
475 spin_lock_init(&miic->lock);
476 miic->dev = dev;
477 miic->base = devm_platform_ioremap_resource(pdev, 0);
478 if (IS_ERR(miic->base))
479 return PTR_ERR(miic->base);
480
481 ret = devm_pm_runtime_enable(dev);
482 if (ret < 0)
483 return ret;
484
485 ret = pm_runtime_resume_and_get(dev);
486 if (ret < 0)
487 return ret;
488
489 ret = miic_init_hw(miic, mode_cfg);
490 if (ret)
491 goto disable_runtime_pm;
492
493 /* miic_create() relies on that fact that data are attached to the
494 * platform device to determine if the driver is ready so this needs to
495 * be the last thing to be done after everything is initialized
496 * properly.
497 */
498 platform_set_drvdata(pdev, miic);
499
500 return 0;
501
502 disable_runtime_pm:
503 pm_runtime_put(dev);
504
505 return ret;
506 }
507
miic_remove(struct platform_device * pdev)508 static int miic_remove(struct platform_device *pdev)
509 {
510 pm_runtime_put(&pdev->dev);
511
512 return 0;
513 }
514
515 static const struct of_device_id miic_of_mtable[] = {
516 { .compatible = "renesas,rzn1-miic" },
517 { /* sentinel */ },
518 };
519 MODULE_DEVICE_TABLE(of, miic_of_mtable);
520
521 static struct platform_driver miic_driver = {
522 .driver = {
523 .name = "rzn1_miic",
524 .suppress_bind_attrs = true,
525 .of_match_table = miic_of_mtable,
526 },
527 .probe = miic_probe,
528 .remove = miic_remove,
529 };
530 module_platform_driver(miic_driver);
531
532 MODULE_LICENSE("GPL");
533 MODULE_DESCRIPTION("Renesas MII converter PCS driver");
534 MODULE_AUTHOR("Clément Léger <clement.leger@bootlin.com>");
535