1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* Driver for TI CC2520 802.15.4 Wireless-PAN Networking controller 3 * 4 * Copyright (C) 2014 Varka Bhadram <varkab@cdac.in> 5 * Md.Jamal Mohiuddin <mjmohiuddin@cdac.in> 6 * P Sowjanya <sowjanyap@cdac.in> 7 */ 8 #include <linux/kernel.h> 9 #include <linux/module.h> 10 #include <linux/gpio.h> 11 #include <linux/delay.h> 12 #include <linux/spi/spi.h> 13 #include <linux/spi/cc2520.h> 14 #include <linux/workqueue.h> 15 #include <linux/interrupt.h> 16 #include <linux/skbuff.h> 17 #include <linux/of_gpio.h> 18 #include <linux/ieee802154.h> 19 #include <linux/crc-ccitt.h> 20 #include <asm/unaligned.h> 21 22 #include <net/mac802154.h> 23 #include <net/cfg802154.h> 24 25 #define SPI_COMMAND_BUFFER 3 26 #define HIGH 1 27 #define LOW 0 28 #define STATE_IDLE 0 29 #define RSSI_VALID 0 30 #define RSSI_OFFSET 78 31 32 #define CC2520_RAM_SIZE 640 33 #define CC2520_FIFO_SIZE 128 34 35 #define CC2520RAM_TXFIFO 0x100 36 #define CC2520RAM_RXFIFO 0x180 37 #define CC2520RAM_IEEEADDR 0x3EA 38 #define CC2520RAM_PANID 0x3F2 39 #define CC2520RAM_SHORTADDR 0x3F4 40 41 #define CC2520_FREG_MASK 0x3F 42 43 /* status byte values */ 44 #define CC2520_STATUS_XOSC32M_STABLE BIT(7) 45 #define CC2520_STATUS_RSSI_VALID BIT(6) 46 #define CC2520_STATUS_TX_UNDERFLOW BIT(3) 47 48 /* IEEE-802.15.4 defined constants (2.4 GHz logical channels) */ 49 #define CC2520_MINCHANNEL 11 50 #define CC2520_MAXCHANNEL 26 51 #define CC2520_CHANNEL_SPACING 5 52 53 /* command strobes */ 54 #define CC2520_CMD_SNOP 0x00 55 #define CC2520_CMD_IBUFLD 0x02 56 #define CC2520_CMD_SIBUFEX 0x03 57 #define CC2520_CMD_SSAMPLECCA 0x04 58 #define CC2520_CMD_SRES 0x0f 59 #define CC2520_CMD_MEMORY_MASK 0x0f 60 #define CC2520_CMD_MEMORY_READ 0x10 61 #define CC2520_CMD_MEMORY_WRITE 0x20 62 #define CC2520_CMD_RXBUF 0x30 63 #define CC2520_CMD_RXBUFCP 0x38 64 #define CC2520_CMD_RXBUFMOV 0x32 65 #define CC2520_CMD_TXBUF 0x3A 66 #define CC2520_CMD_TXBUFCP 0x3E 67 #define CC2520_CMD_RANDOM 0x3C 68 #define CC2520_CMD_SXOSCON 0x40 69 #define CC2520_CMD_STXCAL 0x41 70 #define CC2520_CMD_SRXON 0x42 71 #define CC2520_CMD_STXON 0x43 72 #define CC2520_CMD_STXONCCA 0x44 73 #define CC2520_CMD_SRFOFF 0x45 74 #define CC2520_CMD_SXOSCOFF 0x46 75 #define CC2520_CMD_SFLUSHRX 0x47 76 #define CC2520_CMD_SFLUSHTX 0x48 77 #define CC2520_CMD_SACK 0x49 78 #define CC2520_CMD_SACKPEND 0x4A 79 #define CC2520_CMD_SNACK 0x4B 80 #define CC2520_CMD_SRXMASKBITSET 0x4C 81 #define CC2520_CMD_SRXMASKBITCLR 0x4D 82 #define CC2520_CMD_RXMASKAND 0x4E 83 #define CC2520_CMD_RXMASKOR 0x4F 84 #define CC2520_CMD_MEMCP 0x50 85 #define CC2520_CMD_MEMCPR 0x52 86 #define CC2520_CMD_MEMXCP 0x54 87 #define CC2520_CMD_MEMXWR 0x56 88 #define CC2520_CMD_BCLR 0x58 89 #define CC2520_CMD_BSET 0x59 90 #define CC2520_CMD_CTR_UCTR 0x60 91 #define CC2520_CMD_CBCMAC 0x64 92 #define CC2520_CMD_UCBCMAC 0x66 93 #define CC2520_CMD_CCM 0x68 94 #define CC2520_CMD_UCCM 0x6A 95 #define CC2520_CMD_ECB 0x70 96 #define CC2520_CMD_ECBO 0x72 97 #define CC2520_CMD_ECBX 0x74 98 #define CC2520_CMD_INC 0x78 99 #define CC2520_CMD_ABORT 0x7F 100 #define CC2520_CMD_REGISTER_READ 0x80 101 #define CC2520_CMD_REGISTER_WRITE 0xC0 102 103 /* status registers */ 104 #define CC2520_CHIPID 0x40 105 #define CC2520_VERSION 0x42 106 #define CC2520_EXTCLOCK 0x44 107 #define CC2520_MDMCTRL0 0x46 108 #define CC2520_MDMCTRL1 0x47 109 #define CC2520_FREQEST 0x48 110 #define CC2520_RXCTRL 0x4A 111 #define CC2520_FSCTRL 0x4C 112 #define CC2520_FSCAL0 0x4E 113 #define CC2520_FSCAL1 0x4F 114 #define CC2520_FSCAL2 0x50 115 #define CC2520_FSCAL3 0x51 116 #define CC2520_AGCCTRL0 0x52 117 #define CC2520_AGCCTRL1 0x53 118 #define CC2520_AGCCTRL2 0x54 119 #define CC2520_AGCCTRL3 0x55 120 #define CC2520_ADCTEST0 0x56 121 #define CC2520_ADCTEST1 0x57 122 #define CC2520_ADCTEST2 0x58 123 #define CC2520_MDMTEST0 0x5A 124 #define CC2520_MDMTEST1 0x5B 125 #define CC2520_DACTEST0 0x5C 126 #define CC2520_DACTEST1 0x5D 127 #define CC2520_ATEST 0x5E 128 #define CC2520_DACTEST2 0x5F 129 #define CC2520_PTEST0 0x60 130 #define CC2520_PTEST1 0x61 131 #define CC2520_RESERVED 0x62 132 #define CC2520_DPUBIST 0x7A 133 #define CC2520_ACTBIST 0x7C 134 #define CC2520_RAMBIST 0x7E 135 136 /* frame registers */ 137 #define CC2520_FRMFILT0 0x00 138 #define CC2520_FRMFILT1 0x01 139 #define CC2520_SRCMATCH 0x02 140 #define CC2520_SRCSHORTEN0 0x04 141 #define CC2520_SRCSHORTEN1 0x05 142 #define CC2520_SRCSHORTEN2 0x06 143 #define CC2520_SRCEXTEN0 0x08 144 #define CC2520_SRCEXTEN1 0x09 145 #define CC2520_SRCEXTEN2 0x0A 146 #define CC2520_FRMCTRL0 0x0C 147 #define CC2520_FRMCTRL1 0x0D 148 #define CC2520_RXENABLE0 0x0E 149 #define CC2520_RXENABLE1 0x0F 150 #define CC2520_EXCFLAG0 0x10 151 #define CC2520_EXCFLAG1 0x11 152 #define CC2520_EXCFLAG2 0x12 153 #define CC2520_EXCMASKA0 0x14 154 #define CC2520_EXCMASKA1 0x15 155 #define CC2520_EXCMASKA2 0x16 156 #define CC2520_EXCMASKB0 0x18 157 #define CC2520_EXCMASKB1 0x19 158 #define CC2520_EXCMASKB2 0x1A 159 #define CC2520_EXCBINDX0 0x1C 160 #define CC2520_EXCBINDX1 0x1D 161 #define CC2520_EXCBINDY0 0x1E 162 #define CC2520_EXCBINDY1 0x1F 163 #define CC2520_GPIOCTRL0 0x20 164 #define CC2520_GPIOCTRL1 0x21 165 #define CC2520_GPIOCTRL2 0x22 166 #define CC2520_GPIOCTRL3 0x23 167 #define CC2520_GPIOCTRL4 0x24 168 #define CC2520_GPIOCTRL5 0x25 169 #define CC2520_GPIOPOLARITY 0x26 170 #define CC2520_GPIOCTRL 0x28 171 #define CC2520_DPUCON 0x2A 172 #define CC2520_DPUSTAT 0x2C 173 #define CC2520_FREQCTRL 0x2E 174 #define CC2520_FREQTUNE 0x2F 175 #define CC2520_TXPOWER 0x30 176 #define CC2520_TXCTRL 0x31 177 #define CC2520_FSMSTAT0 0x32 178 #define CC2520_FSMSTAT1 0x33 179 #define CC2520_FIFOPCTRL 0x34 180 #define CC2520_FSMCTRL 0x35 181 #define CC2520_CCACTRL0 0x36 182 #define CC2520_CCACTRL1 0x37 183 #define CC2520_RSSI 0x38 184 #define CC2520_RSSISTAT 0x39 185 #define CC2520_RXFIRST 0x3C 186 #define CC2520_RXFIFOCNT 0x3E 187 #define CC2520_TXFIFOCNT 0x3F 188 189 /* CC2520_FRMFILT0 */ 190 #define FRMFILT0_FRAME_FILTER_EN BIT(0) 191 #define FRMFILT0_PAN_COORDINATOR BIT(1) 192 193 /* CC2520_FRMCTRL0 */ 194 #define FRMCTRL0_AUTOACK BIT(5) 195 #define FRMCTRL0_AUTOCRC BIT(6) 196 197 /* CC2520_FRMCTRL1 */ 198 #define FRMCTRL1_SET_RXENMASK_ON_TX BIT(0) 199 #define FRMCTRL1_IGNORE_TX_UNDERF BIT(1) 200 201 /* Driver private information */ 202 struct cc2520_private { 203 struct spi_device *spi; /* SPI device structure */ 204 struct ieee802154_hw *hw; /* IEEE-802.15.4 device */ 205 u8 *buf; /* SPI TX/Rx data buffer */ 206 struct mutex buffer_mutex; /* SPI buffer mutex */ 207 bool is_tx; /* Flag for sync b/w Tx and Rx */ 208 bool amplified; /* Flag for CC2591 */ 209 int fifo_pin; /* FIFO GPIO pin number */ 210 struct work_struct fifop_irqwork;/* Workqueue for FIFOP */ 211 spinlock_t lock; /* Lock for is_tx*/ 212 struct completion tx_complete; /* Work completion for Tx */ 213 bool promiscuous; /* Flag for promiscuous mode */ 214 }; 215 216 /* Generic Functions */ 217 static int 218 cc2520_cmd_strobe(struct cc2520_private *priv, u8 cmd) 219 { 220 int ret; 221 struct spi_message msg; 222 struct spi_transfer xfer = { 223 .len = 0, 224 .tx_buf = priv->buf, 225 .rx_buf = priv->buf, 226 }; 227 228 spi_message_init(&msg); 229 spi_message_add_tail(&xfer, &msg); 230 231 mutex_lock(&priv->buffer_mutex); 232 priv->buf[xfer.len++] = cmd; 233 dev_vdbg(&priv->spi->dev, 234 "command strobe buf[0] = %02x\n", 235 priv->buf[0]); 236 237 ret = spi_sync(priv->spi, &msg); 238 dev_vdbg(&priv->spi->dev, 239 "buf[0] = %02x\n", priv->buf[0]); 240 mutex_unlock(&priv->buffer_mutex); 241 242 return ret; 243 } 244 245 static int 246 cc2520_get_status(struct cc2520_private *priv, u8 *status) 247 { 248 int ret; 249 struct spi_message msg; 250 struct spi_transfer xfer = { 251 .len = 0, 252 .tx_buf = priv->buf, 253 .rx_buf = priv->buf, 254 }; 255 256 spi_message_init(&msg); 257 spi_message_add_tail(&xfer, &msg); 258 259 mutex_lock(&priv->buffer_mutex); 260 priv->buf[xfer.len++] = CC2520_CMD_SNOP; 261 dev_vdbg(&priv->spi->dev, 262 "get status command buf[0] = %02x\n", priv->buf[0]); 263 264 ret = spi_sync(priv->spi, &msg); 265 if (!ret) 266 *status = priv->buf[0]; 267 dev_vdbg(&priv->spi->dev, 268 "buf[0] = %02x\n", priv->buf[0]); 269 mutex_unlock(&priv->buffer_mutex); 270 271 return ret; 272 } 273 274 static int 275 cc2520_write_register(struct cc2520_private *priv, u8 reg, u8 value) 276 { 277 int status; 278 struct spi_message msg; 279 struct spi_transfer xfer = { 280 .len = 0, 281 .tx_buf = priv->buf, 282 .rx_buf = priv->buf, 283 }; 284 285 spi_message_init(&msg); 286 spi_message_add_tail(&xfer, &msg); 287 288 mutex_lock(&priv->buffer_mutex); 289 290 if (reg <= CC2520_FREG_MASK) { 291 priv->buf[xfer.len++] = CC2520_CMD_REGISTER_WRITE | reg; 292 priv->buf[xfer.len++] = value; 293 } else { 294 priv->buf[xfer.len++] = CC2520_CMD_MEMORY_WRITE; 295 priv->buf[xfer.len++] = reg; 296 priv->buf[xfer.len++] = value; 297 } 298 status = spi_sync(priv->spi, &msg); 299 if (msg.status) 300 status = msg.status; 301 302 mutex_unlock(&priv->buffer_mutex); 303 304 return status; 305 } 306 307 static int 308 cc2520_write_ram(struct cc2520_private *priv, u16 reg, u8 len, u8 *data) 309 { 310 int status; 311 struct spi_message msg; 312 struct spi_transfer xfer_head = { 313 .len = 0, 314 .tx_buf = priv->buf, 315 .rx_buf = priv->buf, 316 }; 317 318 struct spi_transfer xfer_buf = { 319 .len = len, 320 .tx_buf = data, 321 }; 322 323 mutex_lock(&priv->buffer_mutex); 324 priv->buf[xfer_head.len++] = (CC2520_CMD_MEMORY_WRITE | 325 ((reg >> 8) & 0xff)); 326 priv->buf[xfer_head.len++] = reg & 0xff; 327 328 spi_message_init(&msg); 329 spi_message_add_tail(&xfer_head, &msg); 330 spi_message_add_tail(&xfer_buf, &msg); 331 332 status = spi_sync(priv->spi, &msg); 333 dev_dbg(&priv->spi->dev, "spi status = %d\n", status); 334 if (msg.status) 335 status = msg.status; 336 337 mutex_unlock(&priv->buffer_mutex); 338 return status; 339 } 340 341 static int 342 cc2520_read_register(struct cc2520_private *priv, u8 reg, u8 *data) 343 { 344 int status; 345 struct spi_message msg; 346 struct spi_transfer xfer1 = { 347 .len = 0, 348 .tx_buf = priv->buf, 349 .rx_buf = priv->buf, 350 }; 351 352 struct spi_transfer xfer2 = { 353 .len = 1, 354 .rx_buf = data, 355 }; 356 357 spi_message_init(&msg); 358 spi_message_add_tail(&xfer1, &msg); 359 spi_message_add_tail(&xfer2, &msg); 360 361 mutex_lock(&priv->buffer_mutex); 362 priv->buf[xfer1.len++] = CC2520_CMD_MEMORY_READ; 363 priv->buf[xfer1.len++] = reg; 364 365 status = spi_sync(priv->spi, &msg); 366 dev_dbg(&priv->spi->dev, 367 "spi status = %d\n", status); 368 if (msg.status) 369 status = msg.status; 370 371 mutex_unlock(&priv->buffer_mutex); 372 373 return status; 374 } 375 376 static int 377 cc2520_write_txfifo(struct cc2520_private *priv, u8 pkt_len, u8 *data, u8 len) 378 { 379 int status; 380 381 /* length byte must include FCS even 382 * if it is calculated in the hardware 383 */ 384 int len_byte = pkt_len; 385 386 struct spi_message msg; 387 388 struct spi_transfer xfer_head = { 389 .len = 0, 390 .tx_buf = priv->buf, 391 .rx_buf = priv->buf, 392 }; 393 struct spi_transfer xfer_len = { 394 .len = 1, 395 .tx_buf = &len_byte, 396 }; 397 struct spi_transfer xfer_buf = { 398 .len = len, 399 .tx_buf = data, 400 }; 401 402 spi_message_init(&msg); 403 spi_message_add_tail(&xfer_head, &msg); 404 spi_message_add_tail(&xfer_len, &msg); 405 spi_message_add_tail(&xfer_buf, &msg); 406 407 mutex_lock(&priv->buffer_mutex); 408 priv->buf[xfer_head.len++] = CC2520_CMD_TXBUF; 409 dev_vdbg(&priv->spi->dev, 410 "TX_FIFO cmd buf[0] = %02x\n", priv->buf[0]); 411 412 status = spi_sync(priv->spi, &msg); 413 dev_vdbg(&priv->spi->dev, "status = %d\n", status); 414 if (msg.status) 415 status = msg.status; 416 dev_vdbg(&priv->spi->dev, "status = %d\n", status); 417 dev_vdbg(&priv->spi->dev, "buf[0] = %02x\n", priv->buf[0]); 418 mutex_unlock(&priv->buffer_mutex); 419 420 return status; 421 } 422 423 static int 424 cc2520_read_rxfifo(struct cc2520_private *priv, u8 *data, u8 len) 425 { 426 int status; 427 struct spi_message msg; 428 429 struct spi_transfer xfer_head = { 430 .len = 0, 431 .tx_buf = priv->buf, 432 .rx_buf = priv->buf, 433 }; 434 struct spi_transfer xfer_buf = { 435 .len = len, 436 .rx_buf = data, 437 }; 438 439 spi_message_init(&msg); 440 spi_message_add_tail(&xfer_head, &msg); 441 spi_message_add_tail(&xfer_buf, &msg); 442 443 mutex_lock(&priv->buffer_mutex); 444 priv->buf[xfer_head.len++] = CC2520_CMD_RXBUF; 445 446 dev_vdbg(&priv->spi->dev, "read rxfifo buf[0] = %02x\n", priv->buf[0]); 447 dev_vdbg(&priv->spi->dev, "buf[1] = %02x\n", priv->buf[1]); 448 449 status = spi_sync(priv->spi, &msg); 450 dev_vdbg(&priv->spi->dev, "status = %d\n", status); 451 if (msg.status) 452 status = msg.status; 453 dev_vdbg(&priv->spi->dev, "status = %d\n", status); 454 dev_vdbg(&priv->spi->dev, 455 "return status buf[0] = %02x\n", priv->buf[0]); 456 dev_vdbg(&priv->spi->dev, "length buf[1] = %02x\n", priv->buf[1]); 457 458 mutex_unlock(&priv->buffer_mutex); 459 460 return status; 461 } 462 463 static int cc2520_start(struct ieee802154_hw *hw) 464 { 465 return cc2520_cmd_strobe(hw->priv, CC2520_CMD_SRXON); 466 } 467 468 static void cc2520_stop(struct ieee802154_hw *hw) 469 { 470 cc2520_cmd_strobe(hw->priv, CC2520_CMD_SRFOFF); 471 } 472 473 static int 474 cc2520_tx(struct ieee802154_hw *hw, struct sk_buff *skb) 475 { 476 struct cc2520_private *priv = hw->priv; 477 unsigned long flags; 478 int rc; 479 u8 status = 0; 480 u8 pkt_len; 481 482 /* In promiscuous mode we disable AUTOCRC so we can get the raw CRC 483 * values on RX. This means we need to manually add the CRC on TX. 484 */ 485 if (priv->promiscuous) { 486 u16 crc = crc_ccitt(0, skb->data, skb->len); 487 488 put_unaligned_le16(crc, skb_put(skb, 2)); 489 pkt_len = skb->len; 490 } else { 491 pkt_len = skb->len + 2; 492 } 493 494 rc = cc2520_cmd_strobe(priv, CC2520_CMD_SFLUSHTX); 495 if (rc) 496 goto err_tx; 497 498 rc = cc2520_write_txfifo(priv, pkt_len, skb->data, skb->len); 499 if (rc) 500 goto err_tx; 501 502 rc = cc2520_get_status(priv, &status); 503 if (rc) 504 goto err_tx; 505 506 if (status & CC2520_STATUS_TX_UNDERFLOW) { 507 rc = -EINVAL; 508 dev_err(&priv->spi->dev, "cc2520 tx underflow exception\n"); 509 goto err_tx; 510 } 511 512 spin_lock_irqsave(&priv->lock, flags); 513 WARN_ON(priv->is_tx); 514 priv->is_tx = 1; 515 spin_unlock_irqrestore(&priv->lock, flags); 516 517 rc = cc2520_cmd_strobe(priv, CC2520_CMD_STXONCCA); 518 if (rc) 519 goto err; 520 521 rc = wait_for_completion_interruptible(&priv->tx_complete); 522 if (rc < 0) 523 goto err; 524 525 cc2520_cmd_strobe(priv, CC2520_CMD_SFLUSHTX); 526 cc2520_cmd_strobe(priv, CC2520_CMD_SRXON); 527 528 return rc; 529 err: 530 spin_lock_irqsave(&priv->lock, flags); 531 priv->is_tx = 0; 532 spin_unlock_irqrestore(&priv->lock, flags); 533 err_tx: 534 return rc; 535 } 536 537 static int cc2520_rx(struct cc2520_private *priv) 538 { 539 u8 len = 0, lqi = 0, bytes = 1; 540 struct sk_buff *skb; 541 542 /* Read single length byte from the radio. */ 543 cc2520_read_rxfifo(priv, &len, bytes); 544 545 if (!ieee802154_is_valid_psdu_len(len)) { 546 /* Corrupted frame received, clear frame buffer by 547 * reading entire buffer. 548 */ 549 dev_dbg(&priv->spi->dev, "corrupted frame received\n"); 550 len = IEEE802154_MTU; 551 } 552 553 skb = dev_alloc_skb(len); 554 if (!skb) 555 return -ENOMEM; 556 557 if (cc2520_read_rxfifo(priv, skb_put(skb, len), len)) { 558 dev_dbg(&priv->spi->dev, "frame reception failed\n"); 559 kfree_skb(skb); 560 return -EINVAL; 561 } 562 563 /* In promiscuous mode, we configure the radio to include the 564 * CRC (AUTOCRC==0) and we pass on the packet unconditionally. If not 565 * in promiscuous mode, we check the CRC here, but leave the 566 * RSSI/LQI/CRC_OK bytes as they will get removed in the mac layer. 567 */ 568 if (!priv->promiscuous) { 569 bool crc_ok; 570 571 /* Check if the CRC is valid. With AUTOCRC set, the most 572 * significant bit of the last byte returned from the CC2520 573 * is CRC_OK flag. See section 20.3.4 of the datasheet. 574 */ 575 crc_ok = skb->data[len - 1] & BIT(7); 576 577 /* If we failed CRC drop the packet in the driver layer. */ 578 if (!crc_ok) { 579 dev_dbg(&priv->spi->dev, "CRC check failed\n"); 580 kfree_skb(skb); 581 return -EINVAL; 582 } 583 584 /* To calculate LQI, the lower 7 bits of the last byte (the 585 * correlation value provided by the radio) must be scaled to 586 * the range 0-255. According to section 20.6, the correlation 587 * value ranges from 50-110. Ideally this would be calibrated 588 * per hardware design, but we use roughly the datasheet values 589 * to get close enough while avoiding floating point. 590 */ 591 lqi = skb->data[len - 1] & 0x7f; 592 if (lqi < 50) 593 lqi = 50; 594 else if (lqi > 113) 595 lqi = 113; 596 lqi = (lqi - 50) * 4; 597 } 598 599 ieee802154_rx_irqsafe(priv->hw, skb, lqi); 600 601 dev_vdbg(&priv->spi->dev, "RXFIFO: %x %x\n", len, lqi); 602 603 return 0; 604 } 605 606 static int 607 cc2520_ed(struct ieee802154_hw *hw, u8 *level) 608 { 609 struct cc2520_private *priv = hw->priv; 610 u8 status = 0xff; 611 u8 rssi; 612 int ret; 613 614 ret = cc2520_read_register(priv, CC2520_RSSISTAT, &status); 615 if (ret) 616 return ret; 617 618 if (status != RSSI_VALID) 619 return -EINVAL; 620 621 ret = cc2520_read_register(priv, CC2520_RSSI, &rssi); 622 if (ret) 623 return ret; 624 625 /* level = RSSI(rssi) - OFFSET [dBm] : offset is 76dBm */ 626 *level = rssi - RSSI_OFFSET; 627 628 return 0; 629 } 630 631 static int 632 cc2520_set_channel(struct ieee802154_hw *hw, u8 page, u8 channel) 633 { 634 struct cc2520_private *priv = hw->priv; 635 int ret; 636 637 dev_dbg(&priv->spi->dev, "trying to set channel\n"); 638 639 WARN_ON(page != 0); 640 WARN_ON(channel < CC2520_MINCHANNEL); 641 WARN_ON(channel > CC2520_MAXCHANNEL); 642 643 ret = cc2520_write_register(priv, CC2520_FREQCTRL, 644 11 + 5 * (channel - 11)); 645 646 return ret; 647 } 648 649 static int 650 cc2520_filter(struct ieee802154_hw *hw, 651 struct ieee802154_hw_addr_filt *filt, unsigned long changed) 652 { 653 struct cc2520_private *priv = hw->priv; 654 int ret = 0; 655 656 if (changed & IEEE802154_AFILT_PANID_CHANGED) { 657 u16 panid = le16_to_cpu(filt->pan_id); 658 659 dev_vdbg(&priv->spi->dev, "%s called for pan id\n", __func__); 660 ret = cc2520_write_ram(priv, CC2520RAM_PANID, 661 sizeof(panid), (u8 *)&panid); 662 } 663 664 if (changed & IEEE802154_AFILT_IEEEADDR_CHANGED) { 665 dev_vdbg(&priv->spi->dev, 666 "%s called for IEEE addr\n", __func__); 667 ret = cc2520_write_ram(priv, CC2520RAM_IEEEADDR, 668 sizeof(filt->ieee_addr), 669 (u8 *)&filt->ieee_addr); 670 } 671 672 if (changed & IEEE802154_AFILT_SADDR_CHANGED) { 673 u16 addr = le16_to_cpu(filt->short_addr); 674 675 dev_vdbg(&priv->spi->dev, "%s called for saddr\n", __func__); 676 ret = cc2520_write_ram(priv, CC2520RAM_SHORTADDR, 677 sizeof(addr), (u8 *)&addr); 678 } 679 680 if (changed & IEEE802154_AFILT_PANC_CHANGED) { 681 u8 frmfilt0; 682 683 dev_vdbg(&priv->spi->dev, 684 "%s called for panc change\n", __func__); 685 686 cc2520_read_register(priv, CC2520_FRMFILT0, &frmfilt0); 687 688 if (filt->pan_coord) 689 frmfilt0 |= FRMFILT0_PAN_COORDINATOR; 690 else 691 frmfilt0 &= ~FRMFILT0_PAN_COORDINATOR; 692 693 ret = cc2520_write_register(priv, CC2520_FRMFILT0, frmfilt0); 694 } 695 696 return ret; 697 } 698 699 static inline int cc2520_set_tx_power(struct cc2520_private *priv, s32 mbm) 700 { 701 u8 power; 702 703 switch (mbm) { 704 case 500: 705 power = 0xF7; 706 break; 707 case 300: 708 power = 0xF2; 709 break; 710 case 200: 711 power = 0xAB; 712 break; 713 case 100: 714 power = 0x13; 715 break; 716 case 0: 717 power = 0x32; 718 break; 719 case -200: 720 power = 0x81; 721 break; 722 case -400: 723 power = 0x88; 724 break; 725 case -700: 726 power = 0x2C; 727 break; 728 case -1800: 729 power = 0x03; 730 break; 731 default: 732 return -EINVAL; 733 } 734 735 return cc2520_write_register(priv, CC2520_TXPOWER, power); 736 } 737 738 static inline int cc2520_cc2591_set_tx_power(struct cc2520_private *priv, 739 s32 mbm) 740 { 741 u8 power; 742 743 switch (mbm) { 744 case 1700: 745 power = 0xF9; 746 break; 747 case 1600: 748 power = 0xF0; 749 break; 750 case 1400: 751 power = 0xA0; 752 break; 753 case 1100: 754 power = 0x2C; 755 break; 756 case -100: 757 power = 0x03; 758 break; 759 case -800: 760 power = 0x01; 761 break; 762 default: 763 return -EINVAL; 764 } 765 766 return cc2520_write_register(priv, CC2520_TXPOWER, power); 767 } 768 769 #define CC2520_MAX_TX_POWERS 0x8 770 static const s32 cc2520_powers[CC2520_MAX_TX_POWERS + 1] = { 771 500, 300, 200, 100, 0, -200, -400, -700, -1800, 772 }; 773 774 #define CC2520_CC2591_MAX_TX_POWERS 0x5 775 static const s32 cc2520_cc2591_powers[CC2520_CC2591_MAX_TX_POWERS + 1] = { 776 1700, 1600, 1400, 1100, -100, -800, 777 }; 778 779 static int 780 cc2520_set_txpower(struct ieee802154_hw *hw, s32 mbm) 781 { 782 struct cc2520_private *priv = hw->priv; 783 784 if (!priv->amplified) 785 return cc2520_set_tx_power(priv, mbm); 786 787 return cc2520_cc2591_set_tx_power(priv, mbm); 788 } 789 790 static int 791 cc2520_set_promiscuous_mode(struct ieee802154_hw *hw, bool on) 792 { 793 struct cc2520_private *priv = hw->priv; 794 u8 frmfilt0; 795 796 dev_dbg(&priv->spi->dev, "%s : mode %d\n", __func__, on); 797 798 priv->promiscuous = on; 799 800 cc2520_read_register(priv, CC2520_FRMFILT0, &frmfilt0); 801 802 if (on) { 803 /* Disable automatic ACK, automatic CRC, and frame filtering. */ 804 cc2520_write_register(priv, CC2520_FRMCTRL0, 0); 805 frmfilt0 &= ~FRMFILT0_FRAME_FILTER_EN; 806 } else { 807 cc2520_write_register(priv, CC2520_FRMCTRL0, FRMCTRL0_AUTOACK | 808 FRMCTRL0_AUTOCRC); 809 frmfilt0 |= FRMFILT0_FRAME_FILTER_EN; 810 } 811 return cc2520_write_register(priv, CC2520_FRMFILT0, frmfilt0); 812 } 813 814 static const struct ieee802154_ops cc2520_ops = { 815 .owner = THIS_MODULE, 816 .start = cc2520_start, 817 .stop = cc2520_stop, 818 .xmit_sync = cc2520_tx, 819 .ed = cc2520_ed, 820 .set_channel = cc2520_set_channel, 821 .set_hw_addr_filt = cc2520_filter, 822 .set_txpower = cc2520_set_txpower, 823 .set_promiscuous_mode = cc2520_set_promiscuous_mode, 824 }; 825 826 static int cc2520_register(struct cc2520_private *priv) 827 { 828 int ret = -ENOMEM; 829 830 priv->hw = ieee802154_alloc_hw(sizeof(*priv), &cc2520_ops); 831 if (!priv->hw) 832 goto err_ret; 833 834 priv->hw->priv = priv; 835 priv->hw->parent = &priv->spi->dev; 836 priv->hw->extra_tx_headroom = 0; 837 ieee802154_random_extended_addr(&priv->hw->phy->perm_extended_addr); 838 839 /* We do support only 2.4 Ghz */ 840 priv->hw->phy->supported.channels[0] = 0x7FFF800; 841 priv->hw->flags = IEEE802154_HW_TX_OMIT_CKSUM | IEEE802154_HW_AFILT | 842 IEEE802154_HW_PROMISCUOUS; 843 844 priv->hw->phy->flags = WPAN_PHY_FLAG_TXPOWER; 845 846 if (!priv->amplified) { 847 priv->hw->phy->supported.tx_powers = cc2520_powers; 848 priv->hw->phy->supported.tx_powers_size = ARRAY_SIZE(cc2520_powers); 849 priv->hw->phy->transmit_power = priv->hw->phy->supported.tx_powers[4]; 850 } else { 851 priv->hw->phy->supported.tx_powers = cc2520_cc2591_powers; 852 priv->hw->phy->supported.tx_powers_size = ARRAY_SIZE(cc2520_cc2591_powers); 853 priv->hw->phy->transmit_power = priv->hw->phy->supported.tx_powers[0]; 854 } 855 856 priv->hw->phy->current_channel = 11; 857 858 dev_vdbg(&priv->spi->dev, "registered cc2520\n"); 859 ret = ieee802154_register_hw(priv->hw); 860 if (ret) 861 goto err_free_device; 862 863 return 0; 864 865 err_free_device: 866 ieee802154_free_hw(priv->hw); 867 err_ret: 868 return ret; 869 } 870 871 static void cc2520_fifop_irqwork(struct work_struct *work) 872 { 873 struct cc2520_private *priv 874 = container_of(work, struct cc2520_private, fifop_irqwork); 875 876 dev_dbg(&priv->spi->dev, "fifop interrupt received\n"); 877 878 if (gpio_get_value(priv->fifo_pin)) 879 cc2520_rx(priv); 880 else 881 dev_dbg(&priv->spi->dev, "rxfifo overflow\n"); 882 883 cc2520_cmd_strobe(priv, CC2520_CMD_SFLUSHRX); 884 cc2520_cmd_strobe(priv, CC2520_CMD_SFLUSHRX); 885 } 886 887 static irqreturn_t cc2520_fifop_isr(int irq, void *data) 888 { 889 struct cc2520_private *priv = data; 890 891 schedule_work(&priv->fifop_irqwork); 892 893 return IRQ_HANDLED; 894 } 895 896 static irqreturn_t cc2520_sfd_isr(int irq, void *data) 897 { 898 struct cc2520_private *priv = data; 899 unsigned long flags; 900 901 spin_lock_irqsave(&priv->lock, flags); 902 if (priv->is_tx) { 903 priv->is_tx = 0; 904 spin_unlock_irqrestore(&priv->lock, flags); 905 dev_dbg(&priv->spi->dev, "SFD for TX\n"); 906 complete(&priv->tx_complete); 907 } else { 908 spin_unlock_irqrestore(&priv->lock, flags); 909 dev_dbg(&priv->spi->dev, "SFD for RX\n"); 910 } 911 912 return IRQ_HANDLED; 913 } 914 915 static int cc2520_get_platform_data(struct spi_device *spi, 916 struct cc2520_platform_data *pdata) 917 { 918 struct device_node *np = spi->dev.of_node; 919 struct cc2520_private *priv = spi_get_drvdata(spi); 920 921 if (!np) { 922 struct cc2520_platform_data *spi_pdata = spi->dev.platform_data; 923 924 if (!spi_pdata) 925 return -ENOENT; 926 *pdata = *spi_pdata; 927 priv->fifo_pin = pdata->fifo; 928 return 0; 929 } 930 931 pdata->fifo = of_get_named_gpio(np, "fifo-gpio", 0); 932 priv->fifo_pin = pdata->fifo; 933 934 pdata->fifop = of_get_named_gpio(np, "fifop-gpio", 0); 935 936 pdata->sfd = of_get_named_gpio(np, "sfd-gpio", 0); 937 pdata->cca = of_get_named_gpio(np, "cca-gpio", 0); 938 pdata->vreg = of_get_named_gpio(np, "vreg-gpio", 0); 939 pdata->reset = of_get_named_gpio(np, "reset-gpio", 0); 940 941 /* CC2591 front end for CC2520 */ 942 if (of_property_read_bool(np, "amplified")) 943 priv->amplified = true; 944 945 return 0; 946 } 947 948 static int cc2520_hw_init(struct cc2520_private *priv) 949 { 950 u8 status = 0, state = 0xff; 951 int ret; 952 int timeout = 100; 953 struct cc2520_platform_data pdata; 954 955 ret = cc2520_get_platform_data(priv->spi, &pdata); 956 if (ret) 957 goto err_ret; 958 959 ret = cc2520_read_register(priv, CC2520_FSMSTAT1, &state); 960 if (ret) 961 goto err_ret; 962 963 if (state != STATE_IDLE) 964 return -EINVAL; 965 966 do { 967 ret = cc2520_get_status(priv, &status); 968 if (ret) 969 goto err_ret; 970 971 if (timeout-- <= 0) { 972 dev_err(&priv->spi->dev, "oscillator start failed!\n"); 973 return -ETIMEDOUT; 974 } 975 udelay(1); 976 } while (!(status & CC2520_STATUS_XOSC32M_STABLE)); 977 978 dev_vdbg(&priv->spi->dev, "oscillator brought up\n"); 979 980 /* If the CC2520 is connected to a CC2591 amplifier, we must both 981 * configure GPIOs on the CC2520 to correctly configure the CC2591 982 * and change a couple settings of the CC2520 to work with the 983 * amplifier. See section 8 page 17 of TI application note AN065. 984 * http://www.ti.com/lit/an/swra229a/swra229a.pdf 985 */ 986 if (priv->amplified) { 987 ret = cc2520_write_register(priv, CC2520_AGCCTRL1, 0x16); 988 if (ret) 989 goto err_ret; 990 991 ret = cc2520_write_register(priv, CC2520_GPIOCTRL0, 0x46); 992 if (ret) 993 goto err_ret; 994 995 ret = cc2520_write_register(priv, CC2520_GPIOCTRL5, 0x47); 996 if (ret) 997 goto err_ret; 998 999 ret = cc2520_write_register(priv, CC2520_GPIOPOLARITY, 0x1e); 1000 if (ret) 1001 goto err_ret; 1002 1003 ret = cc2520_write_register(priv, CC2520_TXCTRL, 0xc1); 1004 if (ret) 1005 goto err_ret; 1006 } else { 1007 ret = cc2520_write_register(priv, CC2520_AGCCTRL1, 0x11); 1008 if (ret) 1009 goto err_ret; 1010 } 1011 1012 /* Registers default value: section 28.1 in Datasheet */ 1013 1014 /* Set the CCA threshold to -50 dBm. This seems to have been copied 1015 * from the TinyOS CC2520 driver and is much higher than the -84 dBm 1016 * threshold suggested in the datasheet. 1017 */ 1018 ret = cc2520_write_register(priv, CC2520_CCACTRL0, 0x1A); 1019 if (ret) 1020 goto err_ret; 1021 1022 ret = cc2520_write_register(priv, CC2520_MDMCTRL0, 0x85); 1023 if (ret) 1024 goto err_ret; 1025 1026 ret = cc2520_write_register(priv, CC2520_MDMCTRL1, 0x14); 1027 if (ret) 1028 goto err_ret; 1029 1030 ret = cc2520_write_register(priv, CC2520_RXCTRL, 0x3f); 1031 if (ret) 1032 goto err_ret; 1033 1034 ret = cc2520_write_register(priv, CC2520_FSCTRL, 0x5a); 1035 if (ret) 1036 goto err_ret; 1037 1038 ret = cc2520_write_register(priv, CC2520_FSCAL1, 0x2b); 1039 if (ret) 1040 goto err_ret; 1041 1042 ret = cc2520_write_register(priv, CC2520_ADCTEST0, 0x10); 1043 if (ret) 1044 goto err_ret; 1045 1046 ret = cc2520_write_register(priv, CC2520_ADCTEST1, 0x0e); 1047 if (ret) 1048 goto err_ret; 1049 1050 ret = cc2520_write_register(priv, CC2520_ADCTEST2, 0x03); 1051 if (ret) 1052 goto err_ret; 1053 1054 /* Configure registers correctly for this driver. */ 1055 ret = cc2520_write_register(priv, CC2520_FRMCTRL1, 1056 FRMCTRL1_SET_RXENMASK_ON_TX | 1057 FRMCTRL1_IGNORE_TX_UNDERF); 1058 if (ret) 1059 goto err_ret; 1060 1061 ret = cc2520_write_register(priv, CC2520_FIFOPCTRL, 127); 1062 if (ret) 1063 goto err_ret; 1064 1065 return 0; 1066 1067 err_ret: 1068 return ret; 1069 } 1070 1071 static int cc2520_probe(struct spi_device *spi) 1072 { 1073 struct cc2520_private *priv; 1074 struct cc2520_platform_data pdata; 1075 int ret; 1076 1077 priv = devm_kzalloc(&spi->dev, sizeof(*priv), GFP_KERNEL); 1078 if (!priv) 1079 return -ENOMEM; 1080 1081 spi_set_drvdata(spi, priv); 1082 1083 ret = cc2520_get_platform_data(spi, &pdata); 1084 if (ret < 0) { 1085 dev_err(&spi->dev, "no platform data\n"); 1086 return -EINVAL; 1087 } 1088 1089 priv->spi = spi; 1090 1091 priv->buf = devm_kzalloc(&spi->dev, 1092 SPI_COMMAND_BUFFER, GFP_KERNEL); 1093 if (!priv->buf) 1094 return -ENOMEM; 1095 1096 mutex_init(&priv->buffer_mutex); 1097 INIT_WORK(&priv->fifop_irqwork, cc2520_fifop_irqwork); 1098 spin_lock_init(&priv->lock); 1099 init_completion(&priv->tx_complete); 1100 1101 /* Assumption that CC2591 is not connected */ 1102 priv->amplified = false; 1103 1104 /* Request all the gpio's */ 1105 if (!gpio_is_valid(pdata.fifo)) { 1106 dev_err(&spi->dev, "fifo gpio is not valid\n"); 1107 ret = -EINVAL; 1108 goto err_hw_init; 1109 } 1110 1111 ret = devm_gpio_request_one(&spi->dev, pdata.fifo, 1112 GPIOF_IN, "fifo"); 1113 if (ret) 1114 goto err_hw_init; 1115 1116 if (!gpio_is_valid(pdata.cca)) { 1117 dev_err(&spi->dev, "cca gpio is not valid\n"); 1118 ret = -EINVAL; 1119 goto err_hw_init; 1120 } 1121 1122 ret = devm_gpio_request_one(&spi->dev, pdata.cca, 1123 GPIOF_IN, "cca"); 1124 if (ret) 1125 goto err_hw_init; 1126 1127 if (!gpio_is_valid(pdata.fifop)) { 1128 dev_err(&spi->dev, "fifop gpio is not valid\n"); 1129 ret = -EINVAL; 1130 goto err_hw_init; 1131 } 1132 1133 ret = devm_gpio_request_one(&spi->dev, pdata.fifop, 1134 GPIOF_IN, "fifop"); 1135 if (ret) 1136 goto err_hw_init; 1137 1138 if (!gpio_is_valid(pdata.sfd)) { 1139 dev_err(&spi->dev, "sfd gpio is not valid\n"); 1140 ret = -EINVAL; 1141 goto err_hw_init; 1142 } 1143 1144 ret = devm_gpio_request_one(&spi->dev, pdata.sfd, 1145 GPIOF_IN, "sfd"); 1146 if (ret) 1147 goto err_hw_init; 1148 1149 if (!gpio_is_valid(pdata.reset)) { 1150 dev_err(&spi->dev, "reset gpio is not valid\n"); 1151 ret = -EINVAL; 1152 goto err_hw_init; 1153 } 1154 1155 ret = devm_gpio_request_one(&spi->dev, pdata.reset, 1156 GPIOF_OUT_INIT_LOW, "reset"); 1157 if (ret) 1158 goto err_hw_init; 1159 1160 if (!gpio_is_valid(pdata.vreg)) { 1161 dev_err(&spi->dev, "vreg gpio is not valid\n"); 1162 ret = -EINVAL; 1163 goto err_hw_init; 1164 } 1165 1166 ret = devm_gpio_request_one(&spi->dev, pdata.vreg, 1167 GPIOF_OUT_INIT_LOW, "vreg"); 1168 if (ret) 1169 goto err_hw_init; 1170 1171 gpio_set_value(pdata.vreg, HIGH); 1172 usleep_range(100, 150); 1173 1174 gpio_set_value(pdata.reset, HIGH); 1175 usleep_range(200, 250); 1176 1177 ret = cc2520_hw_init(priv); 1178 if (ret) 1179 goto err_hw_init; 1180 1181 /* Set up fifop interrupt */ 1182 ret = devm_request_irq(&spi->dev, 1183 gpio_to_irq(pdata.fifop), 1184 cc2520_fifop_isr, 1185 IRQF_TRIGGER_RISING, 1186 dev_name(&spi->dev), 1187 priv); 1188 if (ret) { 1189 dev_err(&spi->dev, "could not get fifop irq\n"); 1190 goto err_hw_init; 1191 } 1192 1193 /* Set up sfd interrupt */ 1194 ret = devm_request_irq(&spi->dev, 1195 gpio_to_irq(pdata.sfd), 1196 cc2520_sfd_isr, 1197 IRQF_TRIGGER_FALLING, 1198 dev_name(&spi->dev), 1199 priv); 1200 if (ret) { 1201 dev_err(&spi->dev, "could not get sfd irq\n"); 1202 goto err_hw_init; 1203 } 1204 1205 ret = cc2520_register(priv); 1206 if (ret) 1207 goto err_hw_init; 1208 1209 return 0; 1210 1211 err_hw_init: 1212 mutex_destroy(&priv->buffer_mutex); 1213 flush_work(&priv->fifop_irqwork); 1214 return ret; 1215 } 1216 1217 static void cc2520_remove(struct spi_device *spi) 1218 { 1219 struct cc2520_private *priv = spi_get_drvdata(spi); 1220 1221 mutex_destroy(&priv->buffer_mutex); 1222 flush_work(&priv->fifop_irqwork); 1223 1224 ieee802154_unregister_hw(priv->hw); 1225 ieee802154_free_hw(priv->hw); 1226 } 1227 1228 static const struct spi_device_id cc2520_ids[] = { 1229 {"cc2520", }, 1230 {}, 1231 }; 1232 MODULE_DEVICE_TABLE(spi, cc2520_ids); 1233 1234 static const struct of_device_id cc2520_of_ids[] = { 1235 {.compatible = "ti,cc2520", }, 1236 {}, 1237 }; 1238 MODULE_DEVICE_TABLE(of, cc2520_of_ids); 1239 1240 /* SPI driver structure */ 1241 static struct spi_driver cc2520_driver = { 1242 .driver = { 1243 .name = "cc2520", 1244 .of_match_table = of_match_ptr(cc2520_of_ids), 1245 }, 1246 .id_table = cc2520_ids, 1247 .probe = cc2520_probe, 1248 .remove = cc2520_remove, 1249 }; 1250 module_spi_driver(cc2520_driver); 1251 1252 MODULE_AUTHOR("Varka Bhadram <varkab@cdac.in>"); 1253 MODULE_DESCRIPTION("CC2520 Transceiver Driver"); 1254 MODULE_LICENSE("GPL v2"); 1255