1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * atusb.c - Driver for the ATUSB IEEE 802.15.4 dongle 4 * 5 * Written 2013 by Werner Almesberger <werner@almesberger.net> 6 * 7 * Copyright (c) 2015 - 2016 Stefan Schmidt <stefan@datenfreihafen.org> 8 * 9 * Based on at86rf230.c and spi_atusb.c. 10 * at86rf230.c is 11 * Copyright (C) 2009 Siemens AG 12 * Written by: Dmitry Eremin-Solenikov <dmitry.baryshkov@siemens.com> 13 * 14 * spi_atusb.c is 15 * Copyright (c) 2011 Richard Sharpe <realrichardsharpe@gmail.com> 16 * Copyright (c) 2011 Stefan Schmidt <stefan@datenfreihafen.org> 17 * Copyright (c) 2011 Werner Almesberger <werner@almesberger.net> 18 * 19 * USB initialization is 20 * Copyright (c) 2013 Alexander Aring <alex.aring@gmail.com> 21 * 22 * Busware HUL support is 23 * Copyright (c) 2017 Josef Filzmaier <j.filzmaier@gmx.at> 24 */ 25 26 #include <linux/kernel.h> 27 #include <linux/slab.h> 28 #include <linux/module.h> 29 #include <linux/jiffies.h> 30 #include <linux/usb.h> 31 #include <linux/skbuff.h> 32 33 #include <net/cfg802154.h> 34 #include <net/mac802154.h> 35 36 #include "at86rf230.h" 37 #include "atusb.h" 38 39 #define ATUSB_JEDEC_ATMEL 0x1f /* JEDEC manufacturer ID */ 40 41 #define ATUSB_NUM_RX_URBS 4 /* allow for a bit of local latency */ 42 #define ATUSB_ALLOC_DELAY_MS 100 /* delay after failed allocation */ 43 #define ATUSB_TX_TIMEOUT_MS 200 /* on the air timeout */ 44 45 struct atusb { 46 struct ieee802154_hw *hw; 47 struct usb_device *usb_dev; 48 struct atusb_chip_data *data; 49 int shutdown; /* non-zero if shutting down */ 50 int err; /* set by first error */ 51 52 /* RX variables */ 53 struct delayed_work work; /* memory allocations */ 54 struct usb_anchor idle_urbs; /* URBs waiting to be submitted */ 55 struct usb_anchor rx_urbs; /* URBs waiting for reception */ 56 57 /* TX variables */ 58 struct usb_ctrlrequest tx_dr; 59 struct urb *tx_urb; 60 struct sk_buff *tx_skb; 61 u8 tx_ack_seq; /* current TX ACK sequence number */ 62 63 /* Firmware variable */ 64 unsigned char fw_ver_maj; /* Firmware major version number */ 65 unsigned char fw_ver_min; /* Firmware minor version number */ 66 unsigned char fw_hw_type; /* Firmware hardware type */ 67 }; 68 69 struct atusb_chip_data { 70 u16 t_channel_switch; 71 int rssi_base_val; 72 73 int (*set_channel)(struct ieee802154_hw*, u8, u8); 74 int (*set_txpower)(struct ieee802154_hw*, s32); 75 }; 76 77 /* ----- USB commands without data ----------------------------------------- */ 78 79 /* To reduce the number of error checks in the code, we record the first error 80 * in atusb->err and reject all subsequent requests until the error is cleared. 81 */ 82 83 static int atusb_control_msg(struct atusb *atusb, unsigned int pipe, 84 __u8 request, __u8 requesttype, 85 __u16 value, __u16 index, 86 void *data, __u16 size, int timeout) 87 { 88 struct usb_device *usb_dev = atusb->usb_dev; 89 int ret; 90 91 if (atusb->err) 92 return atusb->err; 93 94 ret = usb_control_msg(usb_dev, pipe, request, requesttype, 95 value, index, data, size, timeout); 96 if (ret < 0) { 97 atusb->err = ret; 98 dev_err(&usb_dev->dev, 99 "%s: req 0x%02x val 0x%x idx 0x%x, error %d\n", 100 __func__, request, value, index, ret); 101 } 102 return ret; 103 } 104 105 static int atusb_command(struct atusb *atusb, u8 cmd, u8 arg) 106 { 107 struct usb_device *usb_dev = atusb->usb_dev; 108 109 dev_dbg(&usb_dev->dev, "%s: cmd = 0x%x\n", __func__, cmd); 110 return atusb_control_msg(atusb, usb_sndctrlpipe(usb_dev, 0), 111 cmd, ATUSB_REQ_TO_DEV, arg, 0, NULL, 0, 1000); 112 } 113 114 static int atusb_write_reg(struct atusb *atusb, u8 reg, u8 value) 115 { 116 struct usb_device *usb_dev = atusb->usb_dev; 117 118 dev_dbg(&usb_dev->dev, "%s: 0x%02x <- 0x%02x\n", __func__, reg, value); 119 return atusb_control_msg(atusb, usb_sndctrlpipe(usb_dev, 0), 120 ATUSB_REG_WRITE, ATUSB_REQ_TO_DEV, 121 value, reg, NULL, 0, 1000); 122 } 123 124 static int atusb_read_reg(struct atusb *atusb, u8 reg) 125 { 126 struct usb_device *usb_dev = atusb->usb_dev; 127 int ret; 128 u8 *buffer; 129 u8 value; 130 131 buffer = kmalloc(1, GFP_KERNEL); 132 if (!buffer) 133 return -ENOMEM; 134 135 dev_dbg(&usb_dev->dev, "%s: reg = 0x%x\n", __func__, reg); 136 ret = atusb_control_msg(atusb, usb_rcvctrlpipe(usb_dev, 0), 137 ATUSB_REG_READ, ATUSB_REQ_FROM_DEV, 138 0, reg, buffer, 1, 1000); 139 140 if (ret >= 0) { 141 value = buffer[0]; 142 kfree(buffer); 143 return value; 144 } else { 145 kfree(buffer); 146 return ret; 147 } 148 } 149 150 static int atusb_write_subreg(struct atusb *atusb, u8 reg, u8 mask, 151 u8 shift, u8 value) 152 { 153 struct usb_device *usb_dev = atusb->usb_dev; 154 u8 orig, tmp; 155 int ret = 0; 156 157 dev_dbg(&usb_dev->dev, "%s: 0x%02x <- 0x%02x\n", __func__, reg, value); 158 159 orig = atusb_read_reg(atusb, reg); 160 161 /* Write the value only into that part of the register which is allowed 162 * by the mask. All other bits stay as before. 163 */ 164 tmp = orig & ~mask; 165 tmp |= (value << shift) & mask; 166 167 if (tmp != orig) 168 ret = atusb_write_reg(atusb, reg, tmp); 169 170 return ret; 171 } 172 173 static int atusb_read_subreg(struct atusb *lp, 174 unsigned int addr, unsigned int mask, 175 unsigned int shift) 176 { 177 int rc; 178 179 rc = atusb_read_reg(lp, addr); 180 rc = (rc & mask) >> shift; 181 182 return rc; 183 } 184 185 static int atusb_get_and_clear_error(struct atusb *atusb) 186 { 187 int err = atusb->err; 188 189 atusb->err = 0; 190 return err; 191 } 192 193 /* ----- skb allocation ---------------------------------------------------- */ 194 195 #define MAX_PSDU 127 196 #define MAX_RX_XFER (1 + MAX_PSDU + 2 + 1) /* PHR+PSDU+CRC+LQI */ 197 198 #define SKB_ATUSB(skb) (*(struct atusb **)(skb)->cb) 199 200 static void atusb_in(struct urb *urb); 201 202 static int atusb_submit_rx_urb(struct atusb *atusb, struct urb *urb) 203 { 204 struct usb_device *usb_dev = atusb->usb_dev; 205 struct sk_buff *skb = urb->context; 206 int ret; 207 208 if (!skb) { 209 skb = alloc_skb(MAX_RX_XFER, GFP_KERNEL); 210 if (!skb) { 211 dev_warn_ratelimited(&usb_dev->dev, 212 "atusb_in: can't allocate skb\n"); 213 return -ENOMEM; 214 } 215 skb_put(skb, MAX_RX_XFER); 216 SKB_ATUSB(skb) = atusb; 217 } 218 219 usb_fill_bulk_urb(urb, usb_dev, usb_rcvbulkpipe(usb_dev, 1), 220 skb->data, MAX_RX_XFER, atusb_in, skb); 221 usb_anchor_urb(urb, &atusb->rx_urbs); 222 223 ret = usb_submit_urb(urb, GFP_KERNEL); 224 if (ret) { 225 usb_unanchor_urb(urb); 226 kfree_skb(skb); 227 urb->context = NULL; 228 } 229 return ret; 230 } 231 232 static void atusb_work_urbs(struct work_struct *work) 233 { 234 struct atusb *atusb = 235 container_of(to_delayed_work(work), struct atusb, work); 236 struct usb_device *usb_dev = atusb->usb_dev; 237 struct urb *urb; 238 int ret; 239 240 if (atusb->shutdown) 241 return; 242 243 do { 244 urb = usb_get_from_anchor(&atusb->idle_urbs); 245 if (!urb) 246 return; 247 ret = atusb_submit_rx_urb(atusb, urb); 248 } while (!ret); 249 250 usb_anchor_urb(urb, &atusb->idle_urbs); 251 dev_warn_ratelimited(&usb_dev->dev, 252 "atusb_in: can't allocate/submit URB (%d)\n", ret); 253 schedule_delayed_work(&atusb->work, 254 msecs_to_jiffies(ATUSB_ALLOC_DELAY_MS) + 1); 255 } 256 257 /* ----- Asynchronous USB -------------------------------------------------- */ 258 259 static void atusb_tx_done(struct atusb *atusb, u8 seq) 260 { 261 struct usb_device *usb_dev = atusb->usb_dev; 262 u8 expect = atusb->tx_ack_seq; 263 264 dev_dbg(&usb_dev->dev, "%s (0x%02x/0x%02x)\n", __func__, seq, expect); 265 if (seq == expect) { 266 /* TODO check for ifs handling in firmware */ 267 ieee802154_xmit_complete(atusb->hw, atusb->tx_skb, false); 268 } else { 269 /* TODO I experience this case when atusb has a tx complete 270 * irq before probing, we should fix the firmware it's an 271 * unlikely case now that seq == expect is then true, but can 272 * happen and fail with a tx_skb = NULL; 273 */ 274 ieee802154_wake_queue(atusb->hw); 275 if (atusb->tx_skb) 276 dev_kfree_skb_irq(atusb->tx_skb); 277 } 278 } 279 280 static void atusb_in_good(struct urb *urb) 281 { 282 struct usb_device *usb_dev = urb->dev; 283 struct sk_buff *skb = urb->context; 284 struct atusb *atusb = SKB_ATUSB(skb); 285 u8 len, lqi; 286 287 if (!urb->actual_length) { 288 dev_dbg(&usb_dev->dev, "atusb_in: zero-sized URB ?\n"); 289 return; 290 } 291 292 len = *skb->data; 293 294 if (urb->actual_length == 1) { 295 atusb_tx_done(atusb, len); 296 return; 297 } 298 299 if (len + 1 > urb->actual_length - 1) { 300 dev_dbg(&usb_dev->dev, "atusb_in: frame len %d+1 > URB %u-1\n", 301 len, urb->actual_length); 302 return; 303 } 304 305 if (!ieee802154_is_valid_psdu_len(len)) { 306 dev_dbg(&usb_dev->dev, "atusb_in: frame corrupted\n"); 307 return; 308 } 309 310 lqi = skb->data[len + 1]; 311 dev_dbg(&usb_dev->dev, "atusb_in: rx len %d lqi 0x%02x\n", len, lqi); 312 skb_pull(skb, 1); /* remove PHR */ 313 skb_trim(skb, len); /* get payload only */ 314 ieee802154_rx_irqsafe(atusb->hw, skb, lqi); 315 urb->context = NULL; /* skb is gone */ 316 } 317 318 static void atusb_in(struct urb *urb) 319 { 320 struct usb_device *usb_dev = urb->dev; 321 struct sk_buff *skb = urb->context; 322 struct atusb *atusb = SKB_ATUSB(skb); 323 324 dev_dbg(&usb_dev->dev, "%s: status %d len %d\n", __func__, 325 urb->status, urb->actual_length); 326 if (urb->status) { 327 if (urb->status == -ENOENT) { /* being killed */ 328 kfree_skb(skb); 329 urb->context = NULL; 330 return; 331 } 332 dev_dbg(&usb_dev->dev, "%s: URB error %d\n", __func__, urb->status); 333 } else { 334 atusb_in_good(urb); 335 } 336 337 usb_anchor_urb(urb, &atusb->idle_urbs); 338 if (!atusb->shutdown) 339 schedule_delayed_work(&atusb->work, 0); 340 } 341 342 /* ----- URB allocation/deallocation --------------------------------------- */ 343 344 static void atusb_free_urbs(struct atusb *atusb) 345 { 346 struct urb *urb; 347 348 while (1) { 349 urb = usb_get_from_anchor(&atusb->idle_urbs); 350 if (!urb) 351 break; 352 kfree_skb(urb->context); 353 usb_free_urb(urb); 354 } 355 } 356 357 static int atusb_alloc_urbs(struct atusb *atusb, int n) 358 { 359 struct urb *urb; 360 361 while (n) { 362 urb = usb_alloc_urb(0, GFP_KERNEL); 363 if (!urb) { 364 atusb_free_urbs(atusb); 365 return -ENOMEM; 366 } 367 usb_anchor_urb(urb, &atusb->idle_urbs); 368 n--; 369 } 370 return 0; 371 } 372 373 /* ----- IEEE 802.15.4 interface operations -------------------------------- */ 374 375 static void atusb_xmit_complete(struct urb *urb) 376 { 377 dev_dbg(&urb->dev->dev, "atusb_xmit urb completed"); 378 } 379 380 static int atusb_xmit(struct ieee802154_hw *hw, struct sk_buff *skb) 381 { 382 struct atusb *atusb = hw->priv; 383 struct usb_device *usb_dev = atusb->usb_dev; 384 int ret; 385 386 dev_dbg(&usb_dev->dev, "%s (%d)\n", __func__, skb->len); 387 atusb->tx_skb = skb; 388 atusb->tx_ack_seq++; 389 atusb->tx_dr.wIndex = cpu_to_le16(atusb->tx_ack_seq); 390 atusb->tx_dr.wLength = cpu_to_le16(skb->len); 391 392 usb_fill_control_urb(atusb->tx_urb, usb_dev, 393 usb_sndctrlpipe(usb_dev, 0), 394 (unsigned char *)&atusb->tx_dr, skb->data, 395 skb->len, atusb_xmit_complete, NULL); 396 ret = usb_submit_urb(atusb->tx_urb, GFP_ATOMIC); 397 dev_dbg(&usb_dev->dev, "%s done (%d)\n", __func__, ret); 398 return ret; 399 } 400 401 static int atusb_ed(struct ieee802154_hw *hw, u8 *level) 402 { 403 WARN_ON(!level); 404 *level = 0xbe; 405 return 0; 406 } 407 408 static int atusb_set_hw_addr_filt(struct ieee802154_hw *hw, 409 struct ieee802154_hw_addr_filt *filt, 410 unsigned long changed) 411 { 412 struct atusb *atusb = hw->priv; 413 struct device *dev = &atusb->usb_dev->dev; 414 415 if (changed & IEEE802154_AFILT_SADDR_CHANGED) { 416 u16 addr = le16_to_cpu(filt->short_addr); 417 418 dev_vdbg(dev, "%s called for saddr\n", __func__); 419 atusb_write_reg(atusb, RG_SHORT_ADDR_0, addr); 420 atusb_write_reg(atusb, RG_SHORT_ADDR_1, addr >> 8); 421 } 422 423 if (changed & IEEE802154_AFILT_PANID_CHANGED) { 424 u16 pan = le16_to_cpu(filt->pan_id); 425 426 dev_vdbg(dev, "%s called for pan id\n", __func__); 427 atusb_write_reg(atusb, RG_PAN_ID_0, pan); 428 atusb_write_reg(atusb, RG_PAN_ID_1, pan >> 8); 429 } 430 431 if (changed & IEEE802154_AFILT_IEEEADDR_CHANGED) { 432 u8 i, addr[IEEE802154_EXTENDED_ADDR_LEN]; 433 434 memcpy(addr, &filt->ieee_addr, IEEE802154_EXTENDED_ADDR_LEN); 435 dev_vdbg(dev, "%s called for IEEE addr\n", __func__); 436 for (i = 0; i < 8; i++) 437 atusb_write_reg(atusb, RG_IEEE_ADDR_0 + i, addr[i]); 438 } 439 440 if (changed & IEEE802154_AFILT_PANC_CHANGED) { 441 dev_vdbg(dev, "%s called for panc change\n", __func__); 442 if (filt->pan_coord) 443 atusb_write_subreg(atusb, SR_AACK_I_AM_COORD, 1); 444 else 445 atusb_write_subreg(atusb, SR_AACK_I_AM_COORD, 0); 446 } 447 448 return atusb_get_and_clear_error(atusb); 449 } 450 451 static int atusb_start(struct ieee802154_hw *hw) 452 { 453 struct atusb *atusb = hw->priv; 454 struct usb_device *usb_dev = atusb->usb_dev; 455 int ret; 456 457 dev_dbg(&usb_dev->dev, "%s\n", __func__); 458 schedule_delayed_work(&atusb->work, 0); 459 atusb_command(atusb, ATUSB_RX_MODE, 1); 460 ret = atusb_get_and_clear_error(atusb); 461 if (ret < 0) 462 usb_kill_anchored_urbs(&atusb->idle_urbs); 463 return ret; 464 } 465 466 static void atusb_stop(struct ieee802154_hw *hw) 467 { 468 struct atusb *atusb = hw->priv; 469 struct usb_device *usb_dev = atusb->usb_dev; 470 471 dev_dbg(&usb_dev->dev, "%s\n", __func__); 472 usb_kill_anchored_urbs(&atusb->idle_urbs); 473 atusb_command(atusb, ATUSB_RX_MODE, 0); 474 atusb_get_and_clear_error(atusb); 475 } 476 477 #define ATUSB_MAX_TX_POWERS 0xF 478 static const s32 atusb_powers[ATUSB_MAX_TX_POWERS + 1] = { 479 300, 280, 230, 180, 130, 70, 0, -100, -200, -300, -400, -500, -700, 480 -900, -1200, -1700, 481 }; 482 483 static int 484 atusb_txpower(struct ieee802154_hw *hw, s32 mbm) 485 { 486 struct atusb *atusb = hw->priv; 487 488 if (atusb->data) 489 return atusb->data->set_txpower(hw, mbm); 490 else 491 return -ENOTSUPP; 492 } 493 494 static int 495 atusb_set_txpower(struct ieee802154_hw *hw, s32 mbm) 496 { 497 struct atusb *atusb = hw->priv; 498 u32 i; 499 500 for (i = 0; i < hw->phy->supported.tx_powers_size; i++) { 501 if (hw->phy->supported.tx_powers[i] == mbm) 502 return atusb_write_subreg(atusb, SR_TX_PWR_23X, i); 503 } 504 505 return -EINVAL; 506 } 507 508 static int 509 hulusb_set_txpower(struct ieee802154_hw *hw, s32 mbm) 510 { 511 u32 i; 512 513 for (i = 0; i < hw->phy->supported.tx_powers_size; i++) { 514 if (hw->phy->supported.tx_powers[i] == mbm) 515 return atusb_write_subreg(hw->priv, SR_TX_PWR_212, i); 516 } 517 518 return -EINVAL; 519 } 520 521 #define ATUSB_MAX_ED_LEVELS 0xF 522 static const s32 atusb_ed_levels[ATUSB_MAX_ED_LEVELS + 1] = { 523 -9100, -8900, -8700, -8500, -8300, -8100, -7900, -7700, -7500, -7300, 524 -7100, -6900, -6700, -6500, -6300, -6100, 525 }; 526 527 #define AT86RF212_MAX_TX_POWERS 0x1F 528 static const s32 at86rf212_powers[AT86RF212_MAX_TX_POWERS + 1] = { 529 500, 400, 300, 200, 100, 0, -100, -200, -300, -400, -500, -600, -700, 530 -800, -900, -1000, -1100, -1200, -1300, -1400, -1500, -1600, -1700, 531 -1800, -1900, -2000, -2100, -2200, -2300, -2400, -2500, -2600, 532 }; 533 534 #define AT86RF2XX_MAX_ED_LEVELS 0xF 535 static const s32 at86rf212_ed_levels_100[AT86RF2XX_MAX_ED_LEVELS + 1] = { 536 -10000, -9800, -9600, -9400, -9200, -9000, -8800, -8600, -8400, -8200, 537 -8000, -7800, -7600, -7400, -7200, -7000, 538 }; 539 540 static const s32 at86rf212_ed_levels_98[AT86RF2XX_MAX_ED_LEVELS + 1] = { 541 -9800, -9600, -9400, -9200, -9000, -8800, -8600, -8400, -8200, -8000, 542 -7800, -7600, -7400, -7200, -7000, -6800, 543 }; 544 545 static int 546 atusb_set_cca_mode(struct ieee802154_hw *hw, const struct wpan_phy_cca *cca) 547 { 548 struct atusb *atusb = hw->priv; 549 u8 val; 550 551 /* mapping 802.15.4 to driver spec */ 552 switch (cca->mode) { 553 case NL802154_CCA_ENERGY: 554 val = 1; 555 break; 556 case NL802154_CCA_CARRIER: 557 val = 2; 558 break; 559 case NL802154_CCA_ENERGY_CARRIER: 560 switch (cca->opt) { 561 case NL802154_CCA_OPT_ENERGY_CARRIER_AND: 562 val = 3; 563 break; 564 case NL802154_CCA_OPT_ENERGY_CARRIER_OR: 565 val = 0; 566 break; 567 default: 568 return -EINVAL; 569 } 570 break; 571 default: 572 return -EINVAL; 573 } 574 575 return atusb_write_subreg(atusb, SR_CCA_MODE, val); 576 } 577 578 static int hulusb_set_cca_ed_level(struct atusb *lp, int rssi_base_val) 579 { 580 unsigned int cca_ed_thres; 581 582 cca_ed_thres = atusb_read_subreg(lp, SR_CCA_ED_THRES); 583 584 switch (rssi_base_val) { 585 case -98: 586 lp->hw->phy->supported.cca_ed_levels = at86rf212_ed_levels_98; 587 lp->hw->phy->supported.cca_ed_levels_size = ARRAY_SIZE(at86rf212_ed_levels_98); 588 lp->hw->phy->cca_ed_level = at86rf212_ed_levels_98[cca_ed_thres]; 589 break; 590 case -100: 591 lp->hw->phy->supported.cca_ed_levels = at86rf212_ed_levels_100; 592 lp->hw->phy->supported.cca_ed_levels_size = ARRAY_SIZE(at86rf212_ed_levels_100); 593 lp->hw->phy->cca_ed_level = at86rf212_ed_levels_100[cca_ed_thres]; 594 break; 595 default: 596 WARN_ON(1); 597 } 598 599 return 0; 600 } 601 602 static int 603 atusb_set_cca_ed_level(struct ieee802154_hw *hw, s32 mbm) 604 { 605 struct atusb *atusb = hw->priv; 606 u32 i; 607 608 for (i = 0; i < hw->phy->supported.cca_ed_levels_size; i++) { 609 if (hw->phy->supported.cca_ed_levels[i] == mbm) 610 return atusb_write_subreg(atusb, SR_CCA_ED_THRES, i); 611 } 612 613 return -EINVAL; 614 } 615 616 static int atusb_channel(struct ieee802154_hw *hw, u8 page, u8 channel) 617 { 618 struct atusb *atusb = hw->priv; 619 int ret = -ENOTSUPP; 620 621 if (atusb->data) { 622 ret = atusb->data->set_channel(hw, page, channel); 623 /* @@@ ugly synchronization */ 624 msleep(atusb->data->t_channel_switch); 625 } 626 627 return ret; 628 } 629 630 static int atusb_set_channel(struct ieee802154_hw *hw, u8 page, u8 channel) 631 { 632 struct atusb *atusb = hw->priv; 633 int ret; 634 635 ret = atusb_write_subreg(atusb, SR_CHANNEL, channel); 636 if (ret < 0) 637 return ret; 638 return 0; 639 } 640 641 static int hulusb_set_channel(struct ieee802154_hw *hw, u8 page, u8 channel) 642 { 643 int rc; 644 int rssi_base_val; 645 646 struct atusb *lp = hw->priv; 647 648 if (channel == 0) 649 rc = atusb_write_subreg(lp, SR_SUB_MODE, 0); 650 else 651 rc = atusb_write_subreg(lp, SR_SUB_MODE, 1); 652 if (rc < 0) 653 return rc; 654 655 if (page == 0) { 656 rc = atusb_write_subreg(lp, SR_BPSK_QPSK, 0); 657 rssi_base_val = -100; 658 } else { 659 rc = atusb_write_subreg(lp, SR_BPSK_QPSK, 1); 660 rssi_base_val = -98; 661 } 662 if (rc < 0) 663 return rc; 664 665 rc = hulusb_set_cca_ed_level(lp, rssi_base_val); 666 if (rc < 0) 667 return rc; 668 669 /* This sets the symbol_duration according frequency on the 212. 670 * TODO move this handling while set channel and page in cfg802154. 671 * We can do that, this timings are according 802.15.4 standard. 672 * If we do that in cfg802154, this is a more generic calculation. 673 * 674 * This should also protected from ifs_timer. Means cancel timer and 675 * init with a new value. For now, this is okay. 676 */ 677 if (channel == 0) { 678 if (page == 0) { 679 /* SUB:0 and BPSK:0 -> BPSK-20 */ 680 lp->hw->phy->symbol_duration = 50; 681 } else { 682 /* SUB:1 and BPSK:0 -> BPSK-40 */ 683 lp->hw->phy->symbol_duration = 25; 684 } 685 } else { 686 if (page == 0) 687 /* SUB:0 and BPSK:1 -> OQPSK-100/200/400 */ 688 lp->hw->phy->symbol_duration = 40; 689 else 690 /* SUB:1 and BPSK:1 -> OQPSK-250/500/1000 */ 691 lp->hw->phy->symbol_duration = 16; 692 } 693 694 lp->hw->phy->lifs_period = IEEE802154_LIFS_PERIOD * 695 lp->hw->phy->symbol_duration; 696 lp->hw->phy->sifs_period = IEEE802154_SIFS_PERIOD * 697 lp->hw->phy->symbol_duration; 698 699 return atusb_write_subreg(lp, SR_CHANNEL, channel); 700 } 701 702 static int 703 atusb_set_csma_params(struct ieee802154_hw *hw, u8 min_be, u8 max_be, u8 retries) 704 { 705 struct atusb *atusb = hw->priv; 706 int ret; 707 708 ret = atusb_write_subreg(atusb, SR_MIN_BE, min_be); 709 if (ret) 710 return ret; 711 712 ret = atusb_write_subreg(atusb, SR_MAX_BE, max_be); 713 if (ret) 714 return ret; 715 716 return atusb_write_subreg(atusb, SR_MAX_CSMA_RETRIES, retries); 717 } 718 719 static int 720 hulusb_set_lbt(struct ieee802154_hw *hw, bool on) 721 { 722 struct atusb *atusb = hw->priv; 723 724 return atusb_write_subreg(atusb, SR_CSMA_LBT_MODE, on); 725 } 726 727 static int 728 atusb_set_frame_retries(struct ieee802154_hw *hw, s8 retries) 729 { 730 struct atusb *atusb = hw->priv; 731 732 return atusb_write_subreg(atusb, SR_MAX_FRAME_RETRIES, retries); 733 } 734 735 static int 736 atusb_set_promiscuous_mode(struct ieee802154_hw *hw, const bool on) 737 { 738 struct atusb *atusb = hw->priv; 739 int ret; 740 741 if (on) { 742 ret = atusb_write_subreg(atusb, SR_AACK_DIS_ACK, 1); 743 if (ret < 0) 744 return ret; 745 746 ret = atusb_write_subreg(atusb, SR_AACK_PROM_MODE, 1); 747 if (ret < 0) 748 return ret; 749 } else { 750 ret = atusb_write_subreg(atusb, SR_AACK_PROM_MODE, 0); 751 if (ret < 0) 752 return ret; 753 754 ret = atusb_write_subreg(atusb, SR_AACK_DIS_ACK, 0); 755 if (ret < 0) 756 return ret; 757 } 758 759 return 0; 760 } 761 762 static struct atusb_chip_data atusb_chip_data = { 763 .t_channel_switch = 1, 764 .rssi_base_val = -91, 765 .set_txpower = atusb_set_txpower, 766 .set_channel = atusb_set_channel, 767 }; 768 769 static struct atusb_chip_data hulusb_chip_data = { 770 .t_channel_switch = 11, 771 .rssi_base_val = -100, 772 .set_txpower = hulusb_set_txpower, 773 .set_channel = hulusb_set_channel, 774 }; 775 776 static const struct ieee802154_ops atusb_ops = { 777 .owner = THIS_MODULE, 778 .xmit_async = atusb_xmit, 779 .ed = atusb_ed, 780 .set_channel = atusb_channel, 781 .start = atusb_start, 782 .stop = atusb_stop, 783 .set_hw_addr_filt = atusb_set_hw_addr_filt, 784 .set_txpower = atusb_txpower, 785 .set_lbt = hulusb_set_lbt, 786 .set_cca_mode = atusb_set_cca_mode, 787 .set_cca_ed_level = atusb_set_cca_ed_level, 788 .set_csma_params = atusb_set_csma_params, 789 .set_frame_retries = atusb_set_frame_retries, 790 .set_promiscuous_mode = atusb_set_promiscuous_mode, 791 }; 792 793 /* ----- Firmware and chip version information ----------------------------- */ 794 795 static int atusb_get_and_show_revision(struct atusb *atusb) 796 { 797 struct usb_device *usb_dev = atusb->usb_dev; 798 char *hw_name; 799 unsigned char *buffer; 800 int ret; 801 802 buffer = kmalloc(3, GFP_KERNEL); 803 if (!buffer) 804 return -ENOMEM; 805 806 /* Get a couple of the ATMega Firmware values */ 807 ret = atusb_control_msg(atusb, usb_rcvctrlpipe(usb_dev, 0), 808 ATUSB_ID, ATUSB_REQ_FROM_DEV, 0, 0, 809 buffer, 3, 1000); 810 if (ret >= 0) { 811 atusb->fw_ver_maj = buffer[0]; 812 atusb->fw_ver_min = buffer[1]; 813 atusb->fw_hw_type = buffer[2]; 814 815 switch (atusb->fw_hw_type) { 816 case ATUSB_HW_TYPE_100813: 817 case ATUSB_HW_TYPE_101216: 818 case ATUSB_HW_TYPE_110131: 819 hw_name = "ATUSB"; 820 atusb->data = &atusb_chip_data; 821 break; 822 case ATUSB_HW_TYPE_RZUSB: 823 hw_name = "RZUSB"; 824 atusb->data = &atusb_chip_data; 825 break; 826 case ATUSB_HW_TYPE_HULUSB: 827 hw_name = "HULUSB"; 828 atusb->data = &hulusb_chip_data; 829 break; 830 default: 831 hw_name = "UNKNOWN"; 832 atusb->err = -ENOTSUPP; 833 ret = -ENOTSUPP; 834 break; 835 } 836 837 dev_info(&usb_dev->dev, 838 "Firmware: major: %u, minor: %u, hardware type: %s (%d)\n", 839 atusb->fw_ver_maj, atusb->fw_ver_min, hw_name, 840 atusb->fw_hw_type); 841 } 842 if (atusb->fw_ver_maj == 0 && atusb->fw_ver_min < 2) { 843 dev_info(&usb_dev->dev, 844 "Firmware version (%u.%u) predates our first public release.", 845 atusb->fw_ver_maj, atusb->fw_ver_min); 846 dev_info(&usb_dev->dev, "Please update to version 0.2 or newer"); 847 } 848 849 kfree(buffer); 850 return ret; 851 } 852 853 static int atusb_get_and_show_build(struct atusb *atusb) 854 { 855 struct usb_device *usb_dev = atusb->usb_dev; 856 char *build; 857 int ret; 858 859 build = kmalloc(ATUSB_BUILD_SIZE + 1, GFP_KERNEL); 860 if (!build) 861 return -ENOMEM; 862 863 ret = atusb_control_msg(atusb, usb_rcvctrlpipe(usb_dev, 0), 864 ATUSB_BUILD, ATUSB_REQ_FROM_DEV, 0, 0, 865 build, ATUSB_BUILD_SIZE, 1000); 866 if (ret >= 0) { 867 build[ret] = 0; 868 dev_info(&usb_dev->dev, "Firmware: build %s\n", build); 869 } 870 871 kfree(build); 872 return ret; 873 } 874 875 static int atusb_get_and_conf_chip(struct atusb *atusb) 876 { 877 struct usb_device *usb_dev = atusb->usb_dev; 878 u8 man_id_0, man_id_1, part_num, version_num; 879 const char *chip; 880 struct ieee802154_hw *hw = atusb->hw; 881 882 man_id_0 = atusb_read_reg(atusb, RG_MAN_ID_0); 883 man_id_1 = atusb_read_reg(atusb, RG_MAN_ID_1); 884 part_num = atusb_read_reg(atusb, RG_PART_NUM); 885 version_num = atusb_read_reg(atusb, RG_VERSION_NUM); 886 887 if (atusb->err) 888 return atusb->err; 889 890 hw->flags = IEEE802154_HW_TX_OMIT_CKSUM | IEEE802154_HW_AFILT | 891 IEEE802154_HW_PROMISCUOUS | IEEE802154_HW_CSMA_PARAMS; 892 893 hw->phy->flags = WPAN_PHY_FLAG_TXPOWER | WPAN_PHY_FLAG_CCA_ED_LEVEL | 894 WPAN_PHY_FLAG_CCA_MODE; 895 896 hw->phy->supported.cca_modes = BIT(NL802154_CCA_ENERGY) | 897 BIT(NL802154_CCA_CARRIER) | 898 BIT(NL802154_CCA_ENERGY_CARRIER); 899 hw->phy->supported.cca_opts = BIT(NL802154_CCA_OPT_ENERGY_CARRIER_AND) | 900 BIT(NL802154_CCA_OPT_ENERGY_CARRIER_OR); 901 902 hw->phy->cca.mode = NL802154_CCA_ENERGY; 903 904 hw->phy->current_page = 0; 905 906 if ((man_id_1 << 8 | man_id_0) != ATUSB_JEDEC_ATMEL) { 907 dev_err(&usb_dev->dev, 908 "non-Atmel transceiver xxxx%02x%02x\n", 909 man_id_1, man_id_0); 910 goto fail; 911 } 912 913 switch (part_num) { 914 case 2: 915 chip = "AT86RF230"; 916 atusb->hw->phy->supported.channels[0] = 0x7FFF800; 917 atusb->hw->phy->current_channel = 11; /* reset default */ 918 atusb->hw->phy->symbol_duration = 16; 919 atusb->hw->phy->supported.tx_powers = atusb_powers; 920 atusb->hw->phy->supported.tx_powers_size = ARRAY_SIZE(atusb_powers); 921 hw->phy->supported.cca_ed_levels = atusb_ed_levels; 922 hw->phy->supported.cca_ed_levels_size = ARRAY_SIZE(atusb_ed_levels); 923 break; 924 case 3: 925 chip = "AT86RF231"; 926 atusb->hw->phy->supported.channels[0] = 0x7FFF800; 927 atusb->hw->phy->current_channel = 11; /* reset default */ 928 atusb->hw->phy->symbol_duration = 16; 929 atusb->hw->phy->supported.tx_powers = atusb_powers; 930 atusb->hw->phy->supported.tx_powers_size = ARRAY_SIZE(atusb_powers); 931 hw->phy->supported.cca_ed_levels = atusb_ed_levels; 932 hw->phy->supported.cca_ed_levels_size = ARRAY_SIZE(atusb_ed_levels); 933 break; 934 case 7: 935 chip = "AT86RF212"; 936 atusb->hw->flags |= IEEE802154_HW_LBT; 937 atusb->hw->phy->supported.channels[0] = 0x00007FF; 938 atusb->hw->phy->supported.channels[2] = 0x00007FF; 939 atusb->hw->phy->current_channel = 5; 940 atusb->hw->phy->symbol_duration = 25; 941 atusb->hw->phy->supported.lbt = NL802154_SUPPORTED_BOOL_BOTH; 942 atusb->hw->phy->supported.tx_powers = at86rf212_powers; 943 atusb->hw->phy->supported.tx_powers_size = ARRAY_SIZE(at86rf212_powers); 944 atusb->hw->phy->supported.cca_ed_levels = at86rf212_ed_levels_100; 945 atusb->hw->phy->supported.cca_ed_levels_size = ARRAY_SIZE(at86rf212_ed_levels_100); 946 break; 947 default: 948 dev_err(&usb_dev->dev, 949 "unexpected transceiver, part 0x%02x version 0x%02x\n", 950 part_num, version_num); 951 goto fail; 952 } 953 954 hw->phy->transmit_power = hw->phy->supported.tx_powers[0]; 955 hw->phy->cca_ed_level = hw->phy->supported.cca_ed_levels[7]; 956 957 dev_info(&usb_dev->dev, "ATUSB: %s version %d\n", chip, version_num); 958 959 return 0; 960 961 fail: 962 atusb->err = -ENODEV; 963 return -ENODEV; 964 } 965 966 static int atusb_set_extended_addr(struct atusb *atusb) 967 { 968 struct usb_device *usb_dev = atusb->usb_dev; 969 unsigned char *buffer; 970 __le64 extended_addr; 971 u64 addr; 972 int ret; 973 974 /* Firmware versions before 0.3 do not support the EUI64_READ command. 975 * Just use a random address and be done. 976 */ 977 if (atusb->fw_ver_maj == 0 && atusb->fw_ver_min < 3) { 978 ieee802154_random_extended_addr(&atusb->hw->phy->perm_extended_addr); 979 return 0; 980 } 981 982 buffer = kmalloc(IEEE802154_EXTENDED_ADDR_LEN, GFP_KERNEL); 983 if (!buffer) 984 return -ENOMEM; 985 986 /* Firmware is new enough so we fetch the address from EEPROM */ 987 ret = atusb_control_msg(atusb, usb_rcvctrlpipe(usb_dev, 0), 988 ATUSB_EUI64_READ, ATUSB_REQ_FROM_DEV, 0, 0, 989 buffer, IEEE802154_EXTENDED_ADDR_LEN, 1000); 990 if (ret < 0) { 991 dev_err(&usb_dev->dev, "failed to fetch extended address, random address set\n"); 992 ieee802154_random_extended_addr(&atusb->hw->phy->perm_extended_addr); 993 kfree(buffer); 994 return ret; 995 } 996 997 memcpy(&extended_addr, buffer, IEEE802154_EXTENDED_ADDR_LEN); 998 /* Check if read address is not empty and the unicast bit is set correctly */ 999 if (!ieee802154_is_valid_extended_unicast_addr(extended_addr)) { 1000 dev_info(&usb_dev->dev, "no permanent extended address found, random address set\n"); 1001 ieee802154_random_extended_addr(&atusb->hw->phy->perm_extended_addr); 1002 } else { 1003 atusb->hw->phy->perm_extended_addr = extended_addr; 1004 addr = swab64((__force u64)atusb->hw->phy->perm_extended_addr); 1005 dev_info(&usb_dev->dev, "Read permanent extended address %8phC from device\n", 1006 &addr); 1007 } 1008 1009 kfree(buffer); 1010 return ret; 1011 } 1012 1013 /* ----- Setup ------------------------------------------------------------- */ 1014 1015 static int atusb_probe(struct usb_interface *interface, 1016 const struct usb_device_id *id) 1017 { 1018 struct usb_device *usb_dev = interface_to_usbdev(interface); 1019 struct ieee802154_hw *hw; 1020 struct atusb *atusb = NULL; 1021 int ret = -ENOMEM; 1022 1023 hw = ieee802154_alloc_hw(sizeof(struct atusb), &atusb_ops); 1024 if (!hw) 1025 return -ENOMEM; 1026 1027 atusb = hw->priv; 1028 atusb->hw = hw; 1029 atusb->usb_dev = usb_get_dev(usb_dev); 1030 usb_set_intfdata(interface, atusb); 1031 1032 atusb->shutdown = 0; 1033 atusb->err = 0; 1034 INIT_DELAYED_WORK(&atusb->work, atusb_work_urbs); 1035 init_usb_anchor(&atusb->idle_urbs); 1036 init_usb_anchor(&atusb->rx_urbs); 1037 1038 if (atusb_alloc_urbs(atusb, ATUSB_NUM_RX_URBS)) 1039 goto fail; 1040 1041 atusb->tx_dr.bRequestType = ATUSB_REQ_TO_DEV; 1042 atusb->tx_dr.bRequest = ATUSB_TX; 1043 atusb->tx_dr.wValue = cpu_to_le16(0); 1044 1045 atusb->tx_urb = usb_alloc_urb(0, GFP_KERNEL); 1046 if (!atusb->tx_urb) 1047 goto fail; 1048 1049 hw->parent = &usb_dev->dev; 1050 1051 atusb_command(atusb, ATUSB_RF_RESET, 0); 1052 atusb_get_and_conf_chip(atusb); 1053 atusb_get_and_show_revision(atusb); 1054 atusb_get_and_show_build(atusb); 1055 atusb_set_extended_addr(atusb); 1056 1057 if ((atusb->fw_ver_maj == 0 && atusb->fw_ver_min >= 3) || atusb->fw_ver_maj > 0) 1058 hw->flags |= IEEE802154_HW_FRAME_RETRIES; 1059 1060 ret = atusb_get_and_clear_error(atusb); 1061 if (ret) { 1062 dev_err(&atusb->usb_dev->dev, 1063 "%s: initialization failed, error = %d\n", 1064 __func__, ret); 1065 goto fail; 1066 } 1067 1068 ret = ieee802154_register_hw(hw); 1069 if (ret) 1070 goto fail; 1071 1072 /* If we just powered on, we're now in P_ON and need to enter TRX_OFF 1073 * explicitly. Any resets after that will send us straight to TRX_OFF, 1074 * making the command below redundant. 1075 */ 1076 atusb_write_reg(atusb, RG_TRX_STATE, STATE_FORCE_TRX_OFF); 1077 msleep(1); /* reset => TRX_OFF, tTR13 = 37 us */ 1078 1079 #if 0 1080 /* Calculating the maximum time available to empty the frame buffer 1081 * on reception: 1082 * 1083 * According to [1], the inter-frame gap is 1084 * R * 20 * 16 us + 128 us 1085 * where R is a random number from 0 to 7. Furthermore, we have 20 bit 1086 * times (80 us at 250 kbps) of SHR of the next frame before the 1087 * transceiver begins storing data in the frame buffer. 1088 * 1089 * This yields a minimum time of 208 us between the last data of a 1090 * frame and the first data of the next frame. This time is further 1091 * reduced by interrupt latency in the atusb firmware. 1092 * 1093 * atusb currently needs about 500 us to retrieve a maximum-sized 1094 * frame. We therefore have to allow reception of a new frame to begin 1095 * while we retrieve the previous frame. 1096 * 1097 * [1] "JN-AN-1035 Calculating data rates in an IEEE 802.15.4-based 1098 * network", Jennic 2006. 1099 * http://www.jennic.com/download_file.php?supportFile=JN-AN-1035%20Calculating%20802-15-4%20Data%20Rates-1v0.pdf 1100 */ 1101 1102 atusb_write_subreg(atusb, SR_RX_SAFE_MODE, 1); 1103 #endif 1104 atusb_write_reg(atusb, RG_IRQ_MASK, 0xff); 1105 1106 ret = atusb_get_and_clear_error(atusb); 1107 if (!ret) 1108 return 0; 1109 1110 dev_err(&atusb->usb_dev->dev, 1111 "%s: setup failed, error = %d\n", 1112 __func__, ret); 1113 1114 ieee802154_unregister_hw(hw); 1115 fail: 1116 atusb_free_urbs(atusb); 1117 usb_kill_urb(atusb->tx_urb); 1118 usb_free_urb(atusb->tx_urb); 1119 usb_put_dev(usb_dev); 1120 ieee802154_free_hw(hw); 1121 return ret; 1122 } 1123 1124 static void atusb_disconnect(struct usb_interface *interface) 1125 { 1126 struct atusb *atusb = usb_get_intfdata(interface); 1127 1128 dev_dbg(&atusb->usb_dev->dev, "%s\n", __func__); 1129 1130 atusb->shutdown = 1; 1131 cancel_delayed_work_sync(&atusb->work); 1132 1133 usb_kill_anchored_urbs(&atusb->rx_urbs); 1134 atusb_free_urbs(atusb); 1135 usb_kill_urb(atusb->tx_urb); 1136 usb_free_urb(atusb->tx_urb); 1137 1138 ieee802154_unregister_hw(atusb->hw); 1139 1140 ieee802154_free_hw(atusb->hw); 1141 1142 usb_set_intfdata(interface, NULL); 1143 usb_put_dev(atusb->usb_dev); 1144 1145 pr_debug("%s done\n", __func__); 1146 } 1147 1148 /* The devices we work with */ 1149 static const struct usb_device_id atusb_device_table[] = { 1150 { 1151 .match_flags = USB_DEVICE_ID_MATCH_DEVICE | 1152 USB_DEVICE_ID_MATCH_INT_INFO, 1153 .idVendor = ATUSB_VENDOR_ID, 1154 .idProduct = ATUSB_PRODUCT_ID, 1155 .bInterfaceClass = USB_CLASS_VENDOR_SPEC 1156 }, 1157 /* end with null element */ 1158 {} 1159 }; 1160 MODULE_DEVICE_TABLE(usb, atusb_device_table); 1161 1162 static struct usb_driver atusb_driver = { 1163 .name = "atusb", 1164 .probe = atusb_probe, 1165 .disconnect = atusb_disconnect, 1166 .id_table = atusb_device_table, 1167 }; 1168 module_usb_driver(atusb_driver); 1169 1170 MODULE_AUTHOR("Alexander Aring <alex.aring@gmail.com>"); 1171 MODULE_AUTHOR("Richard Sharpe <realrichardsharpe@gmail.com>"); 1172 MODULE_AUTHOR("Stefan Schmidt <stefan@datenfreihafen.org>"); 1173 MODULE_AUTHOR("Werner Almesberger <werner@almesberger.net>"); 1174 MODULE_AUTHOR("Josef Filzmaier <j.filzmaier@gmx.at>"); 1175 MODULE_DESCRIPTION("ATUSB IEEE 802.15.4 Driver"); 1176 MODULE_LICENSE("GPL"); 1177