1 /*****************************************************************************/ 2 3 /* 4 * baycom_ser_hdx.c -- baycom ser12 halfduplex radio modem driver. 5 * 6 * Copyright (C) 1996-2000 Thomas Sailer (sailer@ife.ee.ethz.ch) 7 * 8 * This program is free software; you can redistribute it and/or modify 9 * it under the terms of the GNU General Public License as published by 10 * the Free Software Foundation; either version 2 of the License, or 11 * (at your option) any later version. 12 * 13 * This program is distributed in the hope that it will be useful, 14 * but WITHOUT ANY WARRANTY; without even the implied warranty of 15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 16 * GNU General Public License for more details. 17 * 18 * You should have received a copy of the GNU General Public License 19 * along with this program; if not, write to the Free Software 20 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. 21 * 22 * Please note that the GPL allows you to use the driver, NOT the radio. 23 * In order to use the radio, you need a license from the communications 24 * authority of your country. 25 * 26 * 27 * Supported modems 28 * 29 * ser12: This is a very simple 1200 baud AFSK modem. The modem consists only 30 * of a modulator/demodulator chip, usually a TI TCM3105. The computer 31 * is responsible for regenerating the receiver bit clock, as well as 32 * for handling the HDLC protocol. The modem connects to a serial port, 33 * hence the name. Since the serial port is not used as an async serial 34 * port, the kernel driver for serial ports cannot be used, and this 35 * driver only supports standard serial hardware (8250, 16450, 16550A) 36 * 37 * 38 * Command line options (insmod command line) 39 * 40 * mode ser12 hardware DCD 41 * ser12* software DCD 42 * ser12@ hardware/software DCD, i.e. no explicit DCD signal but hardware 43 * mutes audio input to the modem 44 * ser12+ hardware DCD, inverted signal at DCD pin 45 * iobase base address of the port; common values are 0x3f8, 0x2f8, 0x3e8, 0x2e8 46 * irq interrupt line of the port; common values are 4,3 47 * 48 * 49 * History: 50 * 0.1 26.06.1996 Adapted from baycom.c and made network driver interface 51 * 18.10.1996 Changed to new user space access routines (copy_{to,from}_user) 52 * 0.3 26.04.1997 init code/data tagged 53 * 0.4 08.07.1997 alternative ser12 decoding algorithm (uses delta CTS ints) 54 * 0.5 11.11.1997 ser12/par96 split into separate files 55 * 0.6 14.04.1998 cleanups 56 * 0.7 03.08.1999 adapt to Linus' new __setup/__initcall 57 * 0.8 10.08.1999 use module_init/module_exit 58 * 0.9 12.02.2000 adapted to softnet driver interface 59 * 0.10 03.07.2000 fix interface name handling 60 */ 61 62 /*****************************************************************************/ 63 64 #include <linux/capability.h> 65 #include <linux/module.h> 66 #include <linux/ioport.h> 67 #include <linux/string.h> 68 #include <linux/init.h> 69 #include <linux/interrupt.h> 70 #include <linux/uaccess.h> 71 #include <asm/io.h> 72 #include <linux/hdlcdrv.h> 73 #include <linux/baycom.h> 74 #include <linux/jiffies.h> 75 76 /* --------------------------------------------------------------------- */ 77 78 #define BAYCOM_DEBUG 79 80 /* --------------------------------------------------------------------- */ 81 82 static const char bc_drvname[] = "baycom_ser_hdx"; 83 static const char bc_drvinfo[] = KERN_INFO "baycom_ser_hdx: (C) 1996-2000 Thomas Sailer, HB9JNX/AE4WA\n" 84 "baycom_ser_hdx: version 0.10\n"; 85 86 /* --------------------------------------------------------------------- */ 87 88 #define NR_PORTS 4 89 90 static struct net_device *baycom_device[NR_PORTS]; 91 92 /* --------------------------------------------------------------------- */ 93 94 #define RBR(iobase) (iobase+0) 95 #define THR(iobase) (iobase+0) 96 #define IER(iobase) (iobase+1) 97 #define IIR(iobase) (iobase+2) 98 #define FCR(iobase) (iobase+2) 99 #define LCR(iobase) (iobase+3) 100 #define MCR(iobase) (iobase+4) 101 #define LSR(iobase) (iobase+5) 102 #define MSR(iobase) (iobase+6) 103 #define SCR(iobase) (iobase+7) 104 #define DLL(iobase) (iobase+0) 105 #define DLM(iobase) (iobase+1) 106 107 #define SER12_EXTENT 8 108 109 /* ---------------------------------------------------------------------- */ 110 /* 111 * Information that need to be kept for each board. 112 */ 113 114 struct baycom_state { 115 struct hdlcdrv_state hdrv; 116 117 int opt_dcd; 118 119 struct modem_state { 120 short arb_divider; 121 unsigned char flags; 122 unsigned int shreg; 123 struct modem_state_ser12 { 124 unsigned char tx_bit; 125 int dcd_sum0, dcd_sum1, dcd_sum2; 126 unsigned char last_sample; 127 unsigned char last_rxbit; 128 unsigned int dcd_shreg; 129 unsigned int dcd_time; 130 unsigned int bit_pll; 131 unsigned char interm_sample; 132 } ser12; 133 } modem; 134 135 #ifdef BAYCOM_DEBUG 136 struct debug_vals { 137 unsigned long last_jiffies; 138 unsigned cur_intcnt; 139 unsigned last_intcnt; 140 int cur_pllcorr; 141 int last_pllcorr; 142 } debug_vals; 143 #endif /* BAYCOM_DEBUG */ 144 }; 145 146 /* --------------------------------------------------------------------- */ 147 148 static inline void baycom_int_freq(struct baycom_state *bc) 149 { 150 #ifdef BAYCOM_DEBUG 151 unsigned long cur_jiffies = jiffies; 152 /* 153 * measure the interrupt frequency 154 */ 155 bc->debug_vals.cur_intcnt++; 156 if (time_after_eq(cur_jiffies, bc->debug_vals.last_jiffies + HZ)) { 157 bc->debug_vals.last_jiffies = cur_jiffies; 158 bc->debug_vals.last_intcnt = bc->debug_vals.cur_intcnt; 159 bc->debug_vals.cur_intcnt = 0; 160 bc->debug_vals.last_pllcorr = bc->debug_vals.cur_pllcorr; 161 bc->debug_vals.cur_pllcorr = 0; 162 } 163 #endif /* BAYCOM_DEBUG */ 164 } 165 166 /* --------------------------------------------------------------------- */ 167 /* 168 * ===================== SER12 specific routines ========================= 169 */ 170 171 static inline void ser12_set_divisor(struct net_device *dev, 172 unsigned char divisor) 173 { 174 outb(0x81, LCR(dev->base_addr)); /* DLAB = 1 */ 175 outb(divisor, DLL(dev->base_addr)); 176 outb(0, DLM(dev->base_addr)); 177 outb(0x01, LCR(dev->base_addr)); /* word length = 6 */ 178 /* 179 * make sure the next interrupt is generated; 180 * 0 must be used to power the modem; the modem draws its 181 * power from the TxD line 182 */ 183 outb(0x00, THR(dev->base_addr)); 184 /* 185 * it is important not to set the divider while transmitting; 186 * this reportedly makes some UARTs generating interrupts 187 * in the hundredthousands per second region 188 * Reported by: Ignacio.Arenaza@studi.epfl.ch (Ignacio Arenaza Nuno) 189 */ 190 } 191 192 /* --------------------------------------------------------------------- */ 193 194 /* 195 * must call the TX arbitrator every 10ms 196 */ 197 #define SER12_ARB_DIVIDER(bc) (bc->opt_dcd ? 24 : 36) 198 199 #define SER12_DCD_INTERVAL(bc) (bc->opt_dcd ? 12 : 240) 200 201 static inline void ser12_tx(struct net_device *dev, struct baycom_state *bc) 202 { 203 /* one interrupt per channel bit */ 204 ser12_set_divisor(dev, 12); 205 /* 206 * first output the last bit (!) then call HDLC transmitter, 207 * since this may take quite long 208 */ 209 outb(0x0e | (!!bc->modem.ser12.tx_bit), MCR(dev->base_addr)); 210 if (bc->modem.shreg <= 1) 211 bc->modem.shreg = 0x10000 | hdlcdrv_getbits(&bc->hdrv); 212 bc->modem.ser12.tx_bit = !(bc->modem.ser12.tx_bit ^ 213 (bc->modem.shreg & 1)); 214 bc->modem.shreg >>= 1; 215 } 216 217 /* --------------------------------------------------------------------- */ 218 219 static inline void ser12_rx(struct net_device *dev, struct baycom_state *bc) 220 { 221 unsigned char cur_s; 222 /* 223 * do demodulator 224 */ 225 cur_s = inb(MSR(dev->base_addr)) & 0x10; /* the CTS line */ 226 hdlcdrv_channelbit(&bc->hdrv, cur_s); 227 bc->modem.ser12.dcd_shreg = (bc->modem.ser12.dcd_shreg << 1) | 228 (cur_s != bc->modem.ser12.last_sample); 229 bc->modem.ser12.last_sample = cur_s; 230 if(bc->modem.ser12.dcd_shreg & 1) { 231 if (!bc->opt_dcd) { 232 unsigned int dcdspos, dcdsneg; 233 234 dcdspos = dcdsneg = 0; 235 dcdspos += ((bc->modem.ser12.dcd_shreg >> 1) & 1); 236 if (!(bc->modem.ser12.dcd_shreg & 0x7ffffffe)) 237 dcdspos += 2; 238 dcdsneg += ((bc->modem.ser12.dcd_shreg >> 2) & 1); 239 dcdsneg += ((bc->modem.ser12.dcd_shreg >> 3) & 1); 240 dcdsneg += ((bc->modem.ser12.dcd_shreg >> 4) & 1); 241 242 bc->modem.ser12.dcd_sum0 += 16*dcdspos - dcdsneg; 243 } else 244 bc->modem.ser12.dcd_sum0--; 245 } 246 if(!bc->modem.ser12.dcd_time) { 247 hdlcdrv_setdcd(&bc->hdrv, (bc->modem.ser12.dcd_sum0 + 248 bc->modem.ser12.dcd_sum1 + 249 bc->modem.ser12.dcd_sum2) < 0); 250 bc->modem.ser12.dcd_sum2 = bc->modem.ser12.dcd_sum1; 251 bc->modem.ser12.dcd_sum1 = bc->modem.ser12.dcd_sum0; 252 /* offset to ensure DCD off on silent input */ 253 bc->modem.ser12.dcd_sum0 = 2; 254 bc->modem.ser12.dcd_time = SER12_DCD_INTERVAL(bc); 255 } 256 bc->modem.ser12.dcd_time--; 257 if (!bc->opt_dcd) { 258 /* 259 * PLL code for the improved software DCD algorithm 260 */ 261 if (bc->modem.ser12.interm_sample) { 262 /* 263 * intermediate sample; set timing correction to normal 264 */ 265 ser12_set_divisor(dev, 4); 266 } else { 267 /* 268 * do PLL correction and call HDLC receiver 269 */ 270 switch (bc->modem.ser12.dcd_shreg & 7) { 271 case 1: /* transition too late */ 272 ser12_set_divisor(dev, 5); 273 #ifdef BAYCOM_DEBUG 274 bc->debug_vals.cur_pllcorr++; 275 #endif /* BAYCOM_DEBUG */ 276 break; 277 case 4: /* transition too early */ 278 ser12_set_divisor(dev, 3); 279 #ifdef BAYCOM_DEBUG 280 bc->debug_vals.cur_pllcorr--; 281 #endif /* BAYCOM_DEBUG */ 282 break; 283 default: 284 ser12_set_divisor(dev, 4); 285 break; 286 } 287 bc->modem.shreg >>= 1; 288 if (bc->modem.ser12.last_sample == 289 bc->modem.ser12.last_rxbit) 290 bc->modem.shreg |= 0x10000; 291 bc->modem.ser12.last_rxbit = 292 bc->modem.ser12.last_sample; 293 } 294 if (++bc->modem.ser12.interm_sample >= 3) 295 bc->modem.ser12.interm_sample = 0; 296 /* 297 * DCD stuff 298 */ 299 if (bc->modem.ser12.dcd_shreg & 1) { 300 unsigned int dcdspos, dcdsneg; 301 302 dcdspos = dcdsneg = 0; 303 dcdspos += ((bc->modem.ser12.dcd_shreg >> 1) & 1); 304 dcdspos += (!(bc->modem.ser12.dcd_shreg & 0x7ffffffe)) 305 << 1; 306 dcdsneg += ((bc->modem.ser12.dcd_shreg >> 2) & 1); 307 dcdsneg += ((bc->modem.ser12.dcd_shreg >> 3) & 1); 308 dcdsneg += ((bc->modem.ser12.dcd_shreg >> 4) & 1); 309 310 bc->modem.ser12.dcd_sum0 += 16*dcdspos - dcdsneg; 311 } 312 } else { 313 /* 314 * PLL algorithm for the hardware squelch DCD algorithm 315 */ 316 if (bc->modem.ser12.interm_sample) { 317 /* 318 * intermediate sample; set timing correction to normal 319 */ 320 ser12_set_divisor(dev, 6); 321 } else { 322 /* 323 * do PLL correction and call HDLC receiver 324 */ 325 switch (bc->modem.ser12.dcd_shreg & 3) { 326 case 1: /* transition too late */ 327 ser12_set_divisor(dev, 7); 328 #ifdef BAYCOM_DEBUG 329 bc->debug_vals.cur_pllcorr++; 330 #endif /* BAYCOM_DEBUG */ 331 break; 332 case 2: /* transition too early */ 333 ser12_set_divisor(dev, 5); 334 #ifdef BAYCOM_DEBUG 335 bc->debug_vals.cur_pllcorr--; 336 #endif /* BAYCOM_DEBUG */ 337 break; 338 default: 339 ser12_set_divisor(dev, 6); 340 break; 341 } 342 bc->modem.shreg >>= 1; 343 if (bc->modem.ser12.last_sample == 344 bc->modem.ser12.last_rxbit) 345 bc->modem.shreg |= 0x10000; 346 bc->modem.ser12.last_rxbit = 347 bc->modem.ser12.last_sample; 348 } 349 bc->modem.ser12.interm_sample = !bc->modem.ser12.interm_sample; 350 /* 351 * DCD stuff 352 */ 353 bc->modem.ser12.dcd_sum0 -= (bc->modem.ser12.dcd_shreg & 1); 354 } 355 outb(0x0d, MCR(dev->base_addr)); /* transmitter off */ 356 if (bc->modem.shreg & 1) { 357 hdlcdrv_putbits(&bc->hdrv, bc->modem.shreg >> 1); 358 bc->modem.shreg = 0x10000; 359 } 360 if(!bc->modem.ser12.dcd_time) { 361 if (bc->opt_dcd & 1) 362 hdlcdrv_setdcd(&bc->hdrv, !((inb(MSR(dev->base_addr)) ^ bc->opt_dcd) & 0x80)); 363 else 364 hdlcdrv_setdcd(&bc->hdrv, (bc->modem.ser12.dcd_sum0 + 365 bc->modem.ser12.dcd_sum1 + 366 bc->modem.ser12.dcd_sum2) < 0); 367 bc->modem.ser12.dcd_sum2 = bc->modem.ser12.dcd_sum1; 368 bc->modem.ser12.dcd_sum1 = bc->modem.ser12.dcd_sum0; 369 /* offset to ensure DCD off on silent input */ 370 bc->modem.ser12.dcd_sum0 = 2; 371 bc->modem.ser12.dcd_time = SER12_DCD_INTERVAL(bc); 372 } 373 bc->modem.ser12.dcd_time--; 374 } 375 376 /* --------------------------------------------------------------------- */ 377 378 static irqreturn_t ser12_interrupt(int irq, void *dev_id) 379 { 380 struct net_device *dev = (struct net_device *)dev_id; 381 struct baycom_state *bc = netdev_priv(dev); 382 unsigned char iir; 383 384 if (!dev || !bc || bc->hdrv.magic != HDLCDRV_MAGIC) 385 return IRQ_NONE; 386 /* fast way out */ 387 if ((iir = inb(IIR(dev->base_addr))) & 1) 388 return IRQ_NONE; 389 baycom_int_freq(bc); 390 do { 391 switch (iir & 6) { 392 case 6: 393 inb(LSR(dev->base_addr)); 394 break; 395 396 case 4: 397 inb(RBR(dev->base_addr)); 398 break; 399 400 case 2: 401 /* 402 * check if transmitter active 403 */ 404 if (hdlcdrv_ptt(&bc->hdrv)) 405 ser12_tx(dev, bc); 406 else { 407 ser12_rx(dev, bc); 408 bc->modem.arb_divider--; 409 } 410 outb(0x00, THR(dev->base_addr)); 411 break; 412 413 default: 414 inb(MSR(dev->base_addr)); 415 break; 416 } 417 iir = inb(IIR(dev->base_addr)); 418 } while (!(iir & 1)); 419 if (bc->modem.arb_divider <= 0) { 420 bc->modem.arb_divider = SER12_ARB_DIVIDER(bc); 421 local_irq_enable(); 422 hdlcdrv_arbitrate(dev, &bc->hdrv); 423 } 424 local_irq_enable(); 425 hdlcdrv_transmitter(dev, &bc->hdrv); 426 hdlcdrv_receiver(dev, &bc->hdrv); 427 local_irq_disable(); 428 return IRQ_HANDLED; 429 } 430 431 /* --------------------------------------------------------------------- */ 432 433 enum uart { c_uart_unknown, c_uart_8250, 434 c_uart_16450, c_uart_16550, c_uart_16550A}; 435 static const char *uart_str[] = { 436 "unknown", "8250", "16450", "16550", "16550A" 437 }; 438 439 static enum uart ser12_check_uart(unsigned int iobase) 440 { 441 unsigned char b1,b2,b3; 442 enum uart u; 443 enum uart uart_tab[] = 444 { c_uart_16450, c_uart_unknown, c_uart_16550, c_uart_16550A }; 445 446 b1 = inb(MCR(iobase)); 447 outb(b1 | 0x10, MCR(iobase)); /* loopback mode */ 448 b2 = inb(MSR(iobase)); 449 outb(0x1a, MCR(iobase)); 450 b3 = inb(MSR(iobase)) & 0xf0; 451 outb(b1, MCR(iobase)); /* restore old values */ 452 outb(b2, MSR(iobase)); 453 if (b3 != 0x90) 454 return c_uart_unknown; 455 inb(RBR(iobase)); 456 inb(RBR(iobase)); 457 outb(0x01, FCR(iobase)); /* enable FIFOs */ 458 u = uart_tab[(inb(IIR(iobase)) >> 6) & 3]; 459 if (u == c_uart_16450) { 460 outb(0x5a, SCR(iobase)); 461 b1 = inb(SCR(iobase)); 462 outb(0xa5, SCR(iobase)); 463 b2 = inb(SCR(iobase)); 464 if ((b1 != 0x5a) || (b2 != 0xa5)) 465 u = c_uart_8250; 466 } 467 return u; 468 } 469 470 /* --------------------------------------------------------------------- */ 471 472 static int ser12_open(struct net_device *dev) 473 { 474 struct baycom_state *bc = netdev_priv(dev); 475 enum uart u; 476 477 if (!dev || !bc) 478 return -ENXIO; 479 if (!dev->base_addr || dev->base_addr > 0x1000-SER12_EXTENT || 480 dev->irq < 2 || dev->irq > 15) 481 return -ENXIO; 482 if (!request_region(dev->base_addr, SER12_EXTENT, "baycom_ser12")) 483 return -EACCES; 484 memset(&bc->modem, 0, sizeof(bc->modem)); 485 bc->hdrv.par.bitrate = 1200; 486 if ((u = ser12_check_uart(dev->base_addr)) == c_uart_unknown) { 487 release_region(dev->base_addr, SER12_EXTENT); 488 return -EIO; 489 } 490 outb(0, FCR(dev->base_addr)); /* disable FIFOs */ 491 outb(0x0d, MCR(dev->base_addr)); 492 outb(0, IER(dev->base_addr)); 493 if (request_irq(dev->irq, ser12_interrupt, IRQF_SHARED, 494 "baycom_ser12", dev)) { 495 release_region(dev->base_addr, SER12_EXTENT); 496 return -EBUSY; 497 } 498 /* 499 * enable transmitter empty interrupt 500 */ 501 outb(2, IER(dev->base_addr)); 502 /* 503 * set the SIO to 6 Bits/character and 19200 or 28800 baud, so that 504 * we get exactly (hopefully) 2 or 3 interrupts per radio symbol, 505 * depending on the usage of the software DCD routine 506 */ 507 ser12_set_divisor(dev, bc->opt_dcd ? 6 : 4); 508 printk(KERN_INFO "%s: ser12 at iobase 0x%lx irq %u uart %s\n", 509 bc_drvname, dev->base_addr, dev->irq, uart_str[u]); 510 return 0; 511 } 512 513 /* --------------------------------------------------------------------- */ 514 515 static int ser12_close(struct net_device *dev) 516 { 517 struct baycom_state *bc = netdev_priv(dev); 518 519 if (!dev || !bc) 520 return -EINVAL; 521 /* 522 * disable interrupts 523 */ 524 outb(0, IER(dev->base_addr)); 525 outb(1, MCR(dev->base_addr)); 526 free_irq(dev->irq, dev); 527 release_region(dev->base_addr, SER12_EXTENT); 528 printk(KERN_INFO "%s: close ser12 at iobase 0x%lx irq %u\n", 529 bc_drvname, dev->base_addr, dev->irq); 530 return 0; 531 } 532 533 /* --------------------------------------------------------------------- */ 534 /* 535 * ===================== hdlcdrv driver interface ========================= 536 */ 537 538 /* --------------------------------------------------------------------- */ 539 540 static int baycom_ioctl(struct net_device *dev, struct ifreq *ifr, 541 struct hdlcdrv_ioctl *hi, int cmd); 542 543 /* --------------------------------------------------------------------- */ 544 545 static const struct hdlcdrv_ops ser12_ops = { 546 .drvname = bc_drvname, 547 .drvinfo = bc_drvinfo, 548 .open = ser12_open, 549 .close = ser12_close, 550 .ioctl = baycom_ioctl, 551 }; 552 553 /* --------------------------------------------------------------------- */ 554 555 static int baycom_setmode(struct baycom_state *bc, const char *modestr) 556 { 557 if (strchr(modestr, '*')) 558 bc->opt_dcd = 0; 559 else if (strchr(modestr, '+')) 560 bc->opt_dcd = -1; 561 else if (strchr(modestr, '@')) 562 bc->opt_dcd = -2; 563 else 564 bc->opt_dcd = 1; 565 return 0; 566 } 567 568 /* --------------------------------------------------------------------- */ 569 570 static int baycom_ioctl(struct net_device *dev, struct ifreq *ifr, 571 struct hdlcdrv_ioctl *hi, int cmd) 572 { 573 struct baycom_state *bc; 574 struct baycom_ioctl bi; 575 576 if (!dev) 577 return -EINVAL; 578 579 bc = netdev_priv(dev); 580 BUG_ON(bc->hdrv.magic != HDLCDRV_MAGIC); 581 582 if (cmd != SIOCDEVPRIVATE) 583 return -ENOIOCTLCMD; 584 switch (hi->cmd) { 585 default: 586 break; 587 588 case HDLCDRVCTL_GETMODE: 589 strcpy(hi->data.modename, "ser12"); 590 if (bc->opt_dcd <= 0) 591 strcat(hi->data.modename, (!bc->opt_dcd) ? "*" : (bc->opt_dcd == -2) ? "@" : "+"); 592 if (copy_to_user(ifr->ifr_data, hi, sizeof(struct hdlcdrv_ioctl))) 593 return -EFAULT; 594 return 0; 595 596 case HDLCDRVCTL_SETMODE: 597 if (netif_running(dev) || !capable(CAP_NET_ADMIN)) 598 return -EACCES; 599 hi->data.modename[sizeof(hi->data.modename)-1] = '\0'; 600 return baycom_setmode(bc, hi->data.modename); 601 602 case HDLCDRVCTL_MODELIST: 603 strcpy(hi->data.modename, "ser12"); 604 if (copy_to_user(ifr->ifr_data, hi, sizeof(struct hdlcdrv_ioctl))) 605 return -EFAULT; 606 return 0; 607 608 case HDLCDRVCTL_MODEMPARMASK: 609 return HDLCDRV_PARMASK_IOBASE | HDLCDRV_PARMASK_IRQ; 610 611 } 612 613 if (copy_from_user(&bi, ifr->ifr_data, sizeof(bi))) 614 return -EFAULT; 615 switch (bi.cmd) { 616 default: 617 return -ENOIOCTLCMD; 618 619 #ifdef BAYCOM_DEBUG 620 case BAYCOMCTL_GETDEBUG: 621 bi.data.dbg.debug1 = bc->hdrv.ptt_keyed; 622 bi.data.dbg.debug2 = bc->debug_vals.last_intcnt; 623 bi.data.dbg.debug3 = bc->debug_vals.last_pllcorr; 624 break; 625 #endif /* BAYCOM_DEBUG */ 626 627 } 628 if (copy_to_user(ifr->ifr_data, &bi, sizeof(bi))) 629 return -EFAULT; 630 return 0; 631 632 } 633 634 /* --------------------------------------------------------------------- */ 635 636 /* 637 * command line settable parameters 638 */ 639 static char *mode[NR_PORTS] = { "ser12*", }; 640 static int iobase[NR_PORTS] = { 0x3f8, }; 641 static int irq[NR_PORTS] = { 4, }; 642 643 module_param_array(mode, charp, NULL, 0); 644 MODULE_PARM_DESC(mode, "baycom operating mode; * for software DCD"); 645 module_param_hw_array(iobase, int, ioport, NULL, 0); 646 MODULE_PARM_DESC(iobase, "baycom io base address"); 647 module_param_hw_array(irq, int, irq, NULL, 0); 648 MODULE_PARM_DESC(irq, "baycom irq number"); 649 650 MODULE_AUTHOR("Thomas M. Sailer, sailer@ife.ee.ethz.ch, hb9jnx@hb9w.che.eu"); 651 MODULE_DESCRIPTION("Baycom ser12 half duplex amateur radio modem driver"); 652 MODULE_LICENSE("GPL"); 653 654 /* --------------------------------------------------------------------- */ 655 656 static int __init init_baycomserhdx(void) 657 { 658 int i, found = 0; 659 char set_hw = 1; 660 661 printk(bc_drvinfo); 662 /* 663 * register net devices 664 */ 665 for (i = 0; i < NR_PORTS; i++) { 666 struct net_device *dev; 667 struct baycom_state *bc; 668 char ifname[IFNAMSIZ]; 669 670 sprintf(ifname, "bcsh%d", i); 671 672 if (!mode[i]) 673 set_hw = 0; 674 if (!set_hw) 675 iobase[i] = irq[i] = 0; 676 677 dev = hdlcdrv_register(&ser12_ops, 678 sizeof(struct baycom_state), 679 ifname, iobase[i], irq[i], 0); 680 if (IS_ERR(dev)) 681 break; 682 683 bc = netdev_priv(dev); 684 if (set_hw && baycom_setmode(bc, mode[i])) 685 set_hw = 0; 686 found++; 687 baycom_device[i] = dev; 688 } 689 690 if (!found) 691 return -ENXIO; 692 return 0; 693 } 694 695 static void __exit cleanup_baycomserhdx(void) 696 { 697 int i; 698 699 for(i = 0; i < NR_PORTS; i++) { 700 struct net_device *dev = baycom_device[i]; 701 702 if (dev) 703 hdlcdrv_unregister(dev); 704 } 705 } 706 707 module_init(init_baycomserhdx); 708 module_exit(cleanup_baycomserhdx); 709 710 /* --------------------------------------------------------------------- */ 711 712 #ifndef MODULE 713 714 /* 715 * format: baycom_ser_hdx=io,irq,mode 716 * mode: ser12 hardware DCD 717 * ser12* software DCD 718 * ser12@ hardware/software DCD, i.e. no explicit DCD signal but hardware 719 * mutes audio input to the modem 720 * ser12+ hardware DCD, inverted signal at DCD pin 721 */ 722 723 static int __init baycom_ser_hdx_setup(char *str) 724 { 725 static unsigned nr_dev; 726 int ints[3]; 727 728 if (nr_dev >= NR_PORTS) 729 return 0; 730 str = get_options(str, 3, ints); 731 if (ints[0] < 2) 732 return 0; 733 mode[nr_dev] = str; 734 iobase[nr_dev] = ints[1]; 735 irq[nr_dev] = ints[2]; 736 nr_dev++; 737 return 1; 738 } 739 740 __setup("baycom_ser_hdx=", baycom_ser_hdx_setup); 741 742 #endif /* MODULE */ 743 /* --------------------------------------------------------------------- */ 744