1 // SPDX-License-Identifier: GPL-2.0 2 /* Copyright (c) 2015 - 2022 Beijing WangXun Technology Co., Ltd. */ 3 4 #include <linux/etherdevice.h> 5 #include <linux/netdevice.h> 6 #include <linux/if_ether.h> 7 #include <linux/if_vlan.h> 8 #include <linux/iopoll.h> 9 #include <linux/pci.h> 10 11 #include "wx_type.h" 12 #include "wx_lib.h" 13 #include "wx_hw.h" 14 15 static void wx_intr_disable(struct wx *wx, u64 qmask) 16 { 17 u32 mask; 18 19 mask = (qmask & U32_MAX); 20 if (mask) 21 wr32(wx, WX_PX_IMS(0), mask); 22 23 if (wx->mac.type == wx_mac_sp) { 24 mask = (qmask >> 32); 25 if (mask) 26 wr32(wx, WX_PX_IMS(1), mask); 27 } 28 } 29 30 void wx_intr_enable(struct wx *wx, u64 qmask) 31 { 32 u32 mask; 33 34 mask = (qmask & U32_MAX); 35 if (mask) 36 wr32(wx, WX_PX_IMC(0), mask); 37 if (wx->mac.type == wx_mac_sp) { 38 mask = (qmask >> 32); 39 if (mask) 40 wr32(wx, WX_PX_IMC(1), mask); 41 } 42 } 43 EXPORT_SYMBOL(wx_intr_enable); 44 45 /** 46 * wx_irq_disable - Mask off interrupt generation on the NIC 47 * @wx: board private structure 48 **/ 49 void wx_irq_disable(struct wx *wx) 50 { 51 struct pci_dev *pdev = wx->pdev; 52 53 wr32(wx, WX_PX_MISC_IEN, 0); 54 wx_intr_disable(wx, WX_INTR_ALL); 55 56 if (pdev->msix_enabled) { 57 int vector; 58 59 for (vector = 0; vector < wx->num_q_vectors; vector++) 60 synchronize_irq(wx->msix_entries[vector].vector); 61 62 synchronize_irq(wx->msix_entries[vector].vector); 63 } else { 64 synchronize_irq(pdev->irq); 65 } 66 } 67 EXPORT_SYMBOL(wx_irq_disable); 68 69 /* cmd_addr is used for some special command: 70 * 1. to be sector address, when implemented erase sector command 71 * 2. to be flash address when implemented read, write flash address 72 */ 73 static int wx_fmgr_cmd_op(struct wx *wx, u32 cmd, u32 cmd_addr) 74 { 75 u32 cmd_val = 0, val = 0; 76 77 cmd_val = WX_SPI_CMD_CMD(cmd) | 78 WX_SPI_CMD_CLK(WX_SPI_CLK_DIV) | 79 cmd_addr; 80 wr32(wx, WX_SPI_CMD, cmd_val); 81 82 return read_poll_timeout(rd32, val, (val & 0x1), 10, 100000, 83 false, wx, WX_SPI_STATUS); 84 } 85 86 static int wx_flash_read_dword(struct wx *wx, u32 addr, u32 *data) 87 { 88 int ret = 0; 89 90 ret = wx_fmgr_cmd_op(wx, WX_SPI_CMD_READ_DWORD, addr); 91 if (ret < 0) 92 return ret; 93 94 *data = rd32(wx, WX_SPI_DATA); 95 96 return ret; 97 } 98 99 int wx_check_flash_load(struct wx *hw, u32 check_bit) 100 { 101 u32 reg = 0; 102 int err = 0; 103 104 /* if there's flash existing */ 105 if (!(rd32(hw, WX_SPI_STATUS) & 106 WX_SPI_STATUS_FLASH_BYPASS)) { 107 /* wait hw load flash done */ 108 err = read_poll_timeout(rd32, reg, !(reg & check_bit), 20000, 2000000, 109 false, hw, WX_SPI_ILDR_STATUS); 110 if (err < 0) 111 wx_err(hw, "Check flash load timeout.\n"); 112 } 113 114 return err; 115 } 116 EXPORT_SYMBOL(wx_check_flash_load); 117 118 void wx_control_hw(struct wx *wx, bool drv) 119 { 120 /* True : Let firmware know the driver has taken over 121 * False : Let firmware take over control of hw 122 */ 123 wr32m(wx, WX_CFG_PORT_CTL, WX_CFG_PORT_CTL_DRV_LOAD, 124 drv ? WX_CFG_PORT_CTL_DRV_LOAD : 0); 125 } 126 EXPORT_SYMBOL(wx_control_hw); 127 128 /** 129 * wx_mng_present - returns 0 when management capability is present 130 * @wx: pointer to hardware structure 131 */ 132 int wx_mng_present(struct wx *wx) 133 { 134 u32 fwsm; 135 136 fwsm = rd32(wx, WX_MIS_ST); 137 if (fwsm & WX_MIS_ST_MNG_INIT_DN) 138 return 0; 139 else 140 return -EACCES; 141 } 142 EXPORT_SYMBOL(wx_mng_present); 143 144 /* Software lock to be held while software semaphore is being accessed. */ 145 static DEFINE_MUTEX(wx_sw_sync_lock); 146 147 /** 148 * wx_release_sw_sync - Release SW semaphore 149 * @wx: pointer to hardware structure 150 * @mask: Mask to specify which semaphore to release 151 * 152 * Releases the SW semaphore for the specified 153 * function (CSR, PHY0, PHY1, EEPROM, Flash) 154 **/ 155 static void wx_release_sw_sync(struct wx *wx, u32 mask) 156 { 157 mutex_lock(&wx_sw_sync_lock); 158 wr32m(wx, WX_MNG_SWFW_SYNC, mask, 0); 159 mutex_unlock(&wx_sw_sync_lock); 160 } 161 162 /** 163 * wx_acquire_sw_sync - Acquire SW semaphore 164 * @wx: pointer to hardware structure 165 * @mask: Mask to specify which semaphore to acquire 166 * 167 * Acquires the SW semaphore for the specified 168 * function (CSR, PHY0, PHY1, EEPROM, Flash) 169 **/ 170 static int wx_acquire_sw_sync(struct wx *wx, u32 mask) 171 { 172 u32 sem = 0; 173 int ret = 0; 174 175 mutex_lock(&wx_sw_sync_lock); 176 ret = read_poll_timeout(rd32, sem, !(sem & mask), 177 5000, 2000000, false, wx, WX_MNG_SWFW_SYNC); 178 if (!ret) { 179 sem |= mask; 180 wr32(wx, WX_MNG_SWFW_SYNC, sem); 181 } else { 182 wx_err(wx, "SW Semaphore not granted: 0x%x.\n", sem); 183 } 184 mutex_unlock(&wx_sw_sync_lock); 185 186 return ret; 187 } 188 189 /** 190 * wx_host_interface_command - Issue command to manageability block 191 * @wx: pointer to the HW structure 192 * @buffer: contains the command to write and where the return status will 193 * be placed 194 * @length: length of buffer, must be multiple of 4 bytes 195 * @timeout: time in ms to wait for command completion 196 * @return_data: read and return data from the buffer (true) or not (false) 197 * Needed because FW structures are big endian and decoding of 198 * these fields can be 8 bit or 16 bit based on command. Decoding 199 * is not easily understood without making a table of commands. 200 * So we will leave this up to the caller to read back the data 201 * in these cases. 202 **/ 203 int wx_host_interface_command(struct wx *wx, u32 *buffer, 204 u32 length, u32 timeout, bool return_data) 205 { 206 u32 hdr_size = sizeof(struct wx_hic_hdr); 207 u32 hicr, i, bi, buf[64] = {}; 208 int status = 0; 209 u32 dword_len; 210 u16 buf_len; 211 212 if (length == 0 || length > WX_HI_MAX_BLOCK_BYTE_LENGTH) { 213 wx_err(wx, "Buffer length failure buffersize=%d.\n", length); 214 return -EINVAL; 215 } 216 217 status = wx_acquire_sw_sync(wx, WX_MNG_SWFW_SYNC_SW_MB); 218 if (status != 0) 219 return status; 220 221 /* Calculate length in DWORDs. We must be DWORD aligned */ 222 if ((length % (sizeof(u32))) != 0) { 223 wx_err(wx, "Buffer length failure, not aligned to dword"); 224 status = -EINVAL; 225 goto rel_out; 226 } 227 228 dword_len = length >> 2; 229 230 /* The device driver writes the relevant command block 231 * into the ram area. 232 */ 233 for (i = 0; i < dword_len; i++) { 234 wr32a(wx, WX_MNG_MBOX, i, (__force u32)cpu_to_le32(buffer[i])); 235 /* write flush */ 236 buf[i] = rd32a(wx, WX_MNG_MBOX, i); 237 } 238 /* Setting this bit tells the ARC that a new command is pending. */ 239 wr32m(wx, WX_MNG_MBOX_CTL, 240 WX_MNG_MBOX_CTL_SWRDY, WX_MNG_MBOX_CTL_SWRDY); 241 242 status = read_poll_timeout(rd32, hicr, hicr & WX_MNG_MBOX_CTL_FWRDY, 1000, 243 timeout * 1000, false, wx, WX_MNG_MBOX_CTL); 244 245 /* Check command completion */ 246 if (status) { 247 wx_dbg(wx, "Command has failed with no status valid.\n"); 248 249 buf[0] = rd32(wx, WX_MNG_MBOX); 250 if ((buffer[0] & 0xff) != (~buf[0] >> 24)) { 251 status = -EINVAL; 252 goto rel_out; 253 } 254 if ((buf[0] & 0xff0000) >> 16 == 0x80) { 255 wx_dbg(wx, "It's unknown cmd.\n"); 256 status = -EINVAL; 257 goto rel_out; 258 } 259 260 wx_dbg(wx, "write value:\n"); 261 for (i = 0; i < dword_len; i++) 262 wx_dbg(wx, "%x ", buffer[i]); 263 wx_dbg(wx, "read value:\n"); 264 for (i = 0; i < dword_len; i++) 265 wx_dbg(wx, "%x ", buf[i]); 266 } 267 268 if (!return_data) 269 goto rel_out; 270 271 /* Calculate length in DWORDs */ 272 dword_len = hdr_size >> 2; 273 274 /* first pull in the header so we know the buffer length */ 275 for (bi = 0; bi < dword_len; bi++) { 276 buffer[bi] = rd32a(wx, WX_MNG_MBOX, bi); 277 le32_to_cpus(&buffer[bi]); 278 } 279 280 /* If there is any thing in data position pull it in */ 281 buf_len = ((struct wx_hic_hdr *)buffer)->buf_len; 282 if (buf_len == 0) 283 goto rel_out; 284 285 if (length < buf_len + hdr_size) { 286 wx_err(wx, "Buffer not large enough for reply message.\n"); 287 status = -EFAULT; 288 goto rel_out; 289 } 290 291 /* Calculate length in DWORDs, add 3 for odd lengths */ 292 dword_len = (buf_len + 3) >> 2; 293 294 /* Pull in the rest of the buffer (bi is where we left off) */ 295 for (; bi <= dword_len; bi++) { 296 buffer[bi] = rd32a(wx, WX_MNG_MBOX, bi); 297 le32_to_cpus(&buffer[bi]); 298 } 299 300 rel_out: 301 wx_release_sw_sync(wx, WX_MNG_SWFW_SYNC_SW_MB); 302 return status; 303 } 304 EXPORT_SYMBOL(wx_host_interface_command); 305 306 /** 307 * wx_read_ee_hostif_data - Read EEPROM word using a host interface cmd 308 * assuming that the semaphore is already obtained. 309 * @wx: pointer to hardware structure 310 * @offset: offset of word in the EEPROM to read 311 * @data: word read from the EEPROM 312 * 313 * Reads a 16 bit word from the EEPROM using the hostif. 314 **/ 315 static int wx_read_ee_hostif_data(struct wx *wx, u16 offset, u16 *data) 316 { 317 struct wx_hic_read_shadow_ram buffer; 318 int status; 319 320 buffer.hdr.req.cmd = FW_READ_SHADOW_RAM_CMD; 321 buffer.hdr.req.buf_lenh = 0; 322 buffer.hdr.req.buf_lenl = FW_READ_SHADOW_RAM_LEN; 323 buffer.hdr.req.checksum = FW_DEFAULT_CHECKSUM; 324 325 /* convert offset from words to bytes */ 326 buffer.address = (__force u32)cpu_to_be32(offset * 2); 327 /* one word */ 328 buffer.length = (__force u16)cpu_to_be16(sizeof(u16)); 329 330 status = wx_host_interface_command(wx, (u32 *)&buffer, sizeof(buffer), 331 WX_HI_COMMAND_TIMEOUT, false); 332 333 if (status != 0) 334 return status; 335 336 *data = (u16)rd32a(wx, WX_MNG_MBOX, FW_NVM_DATA_OFFSET); 337 338 return status; 339 } 340 341 /** 342 * wx_read_ee_hostif - Read EEPROM word using a host interface cmd 343 * @wx: pointer to hardware structure 344 * @offset: offset of word in the EEPROM to read 345 * @data: word read from the EEPROM 346 * 347 * Reads a 16 bit word from the EEPROM using the hostif. 348 **/ 349 int wx_read_ee_hostif(struct wx *wx, u16 offset, u16 *data) 350 { 351 int status = 0; 352 353 status = wx_acquire_sw_sync(wx, WX_MNG_SWFW_SYNC_SW_FLASH); 354 if (status == 0) { 355 status = wx_read_ee_hostif_data(wx, offset, data); 356 wx_release_sw_sync(wx, WX_MNG_SWFW_SYNC_SW_FLASH); 357 } 358 359 return status; 360 } 361 EXPORT_SYMBOL(wx_read_ee_hostif); 362 363 /** 364 * wx_read_ee_hostif_buffer- Read EEPROM word(s) using hostif 365 * @wx: pointer to hardware structure 366 * @offset: offset of word in the EEPROM to read 367 * @words: number of words 368 * @data: word(s) read from the EEPROM 369 * 370 * Reads a 16 bit word(s) from the EEPROM using the hostif. 371 **/ 372 int wx_read_ee_hostif_buffer(struct wx *wx, 373 u16 offset, u16 words, u16 *data) 374 { 375 struct wx_hic_read_shadow_ram buffer; 376 u32 current_word = 0; 377 u16 words_to_read; 378 u32 value = 0; 379 int status; 380 u32 i; 381 382 /* Take semaphore for the entire operation. */ 383 status = wx_acquire_sw_sync(wx, WX_MNG_SWFW_SYNC_SW_FLASH); 384 if (status != 0) 385 return status; 386 387 while (words) { 388 if (words > FW_MAX_READ_BUFFER_SIZE / 2) 389 words_to_read = FW_MAX_READ_BUFFER_SIZE / 2; 390 else 391 words_to_read = words; 392 393 buffer.hdr.req.cmd = FW_READ_SHADOW_RAM_CMD; 394 buffer.hdr.req.buf_lenh = 0; 395 buffer.hdr.req.buf_lenl = FW_READ_SHADOW_RAM_LEN; 396 buffer.hdr.req.checksum = FW_DEFAULT_CHECKSUM; 397 398 /* convert offset from words to bytes */ 399 buffer.address = (__force u32)cpu_to_be32((offset + current_word) * 2); 400 buffer.length = (__force u16)cpu_to_be16(words_to_read * 2); 401 402 status = wx_host_interface_command(wx, (u32 *)&buffer, 403 sizeof(buffer), 404 WX_HI_COMMAND_TIMEOUT, 405 false); 406 407 if (status != 0) { 408 wx_err(wx, "Host interface command failed\n"); 409 goto out; 410 } 411 412 for (i = 0; i < words_to_read; i++) { 413 u32 reg = WX_MNG_MBOX + (FW_NVM_DATA_OFFSET << 2) + 2 * i; 414 415 value = rd32(wx, reg); 416 data[current_word] = (u16)(value & 0xffff); 417 current_word++; 418 i++; 419 if (i < words_to_read) { 420 value >>= 16; 421 data[current_word] = (u16)(value & 0xffff); 422 current_word++; 423 } 424 } 425 words -= words_to_read; 426 } 427 428 out: 429 wx_release_sw_sync(wx, WX_MNG_SWFW_SYNC_SW_FLASH); 430 return status; 431 } 432 EXPORT_SYMBOL(wx_read_ee_hostif_buffer); 433 434 /** 435 * wx_calculate_checksum - Calculate checksum for buffer 436 * @buffer: pointer to EEPROM 437 * @length: size of EEPROM to calculate a checksum for 438 * Calculates the checksum for some buffer on a specified length. The 439 * checksum calculated is returned. 440 **/ 441 static u8 wx_calculate_checksum(u8 *buffer, u32 length) 442 { 443 u8 sum = 0; 444 u32 i; 445 446 if (!buffer) 447 return 0; 448 449 for (i = 0; i < length; i++) 450 sum += buffer[i]; 451 452 return (u8)(0 - sum); 453 } 454 455 /** 456 * wx_reset_hostif - send reset cmd to fw 457 * @wx: pointer to hardware structure 458 * 459 * Sends reset cmd to firmware through the manageability 460 * block. 461 **/ 462 int wx_reset_hostif(struct wx *wx) 463 { 464 struct wx_hic_reset reset_cmd; 465 int ret_val = 0; 466 int i; 467 468 reset_cmd.hdr.cmd = FW_RESET_CMD; 469 reset_cmd.hdr.buf_len = FW_RESET_LEN; 470 reset_cmd.hdr.cmd_or_resp.cmd_resv = FW_CEM_CMD_RESERVED; 471 reset_cmd.lan_id = wx->bus.func; 472 reset_cmd.reset_type = (u16)wx->reset_type; 473 reset_cmd.hdr.checksum = 0; 474 reset_cmd.hdr.checksum = wx_calculate_checksum((u8 *)&reset_cmd, 475 (FW_CEM_HDR_LEN + 476 reset_cmd.hdr.buf_len)); 477 478 for (i = 0; i <= FW_CEM_MAX_RETRIES; i++) { 479 ret_val = wx_host_interface_command(wx, (u32 *)&reset_cmd, 480 sizeof(reset_cmd), 481 WX_HI_COMMAND_TIMEOUT, 482 true); 483 if (ret_val != 0) 484 continue; 485 486 if (reset_cmd.hdr.cmd_or_resp.ret_status == 487 FW_CEM_RESP_STATUS_SUCCESS) 488 ret_val = 0; 489 else 490 ret_val = -EFAULT; 491 492 break; 493 } 494 495 return ret_val; 496 } 497 EXPORT_SYMBOL(wx_reset_hostif); 498 499 /** 500 * wx_init_eeprom_params - Initialize EEPROM params 501 * @wx: pointer to hardware structure 502 * 503 * Initializes the EEPROM parameters wx_eeprom_info within the 504 * wx_hw struct in order to set up EEPROM access. 505 **/ 506 void wx_init_eeprom_params(struct wx *wx) 507 { 508 struct wx_eeprom_info *eeprom = &wx->eeprom; 509 u16 eeprom_size; 510 u16 data = 0x80; 511 512 if (eeprom->type == wx_eeprom_uninitialized) { 513 eeprom->semaphore_delay = 10; 514 eeprom->type = wx_eeprom_none; 515 516 if (!(rd32(wx, WX_SPI_STATUS) & 517 WX_SPI_STATUS_FLASH_BYPASS)) { 518 eeprom->type = wx_flash; 519 520 eeprom_size = 4096; 521 eeprom->word_size = eeprom_size >> 1; 522 523 wx_dbg(wx, "Eeprom params: type = %d, size = %d\n", 524 eeprom->type, eeprom->word_size); 525 } 526 } 527 528 if (wx->mac.type == wx_mac_sp) { 529 if (wx_read_ee_hostif(wx, WX_SW_REGION_PTR, &data)) { 530 wx_err(wx, "NVM Read Error\n"); 531 return; 532 } 533 data = data >> 1; 534 } 535 536 eeprom->sw_region_offset = data; 537 } 538 EXPORT_SYMBOL(wx_init_eeprom_params); 539 540 /** 541 * wx_get_mac_addr - Generic get MAC address 542 * @wx: pointer to hardware structure 543 * @mac_addr: Adapter MAC address 544 * 545 * Reads the adapter's MAC address from first Receive Address Register (RAR0) 546 * A reset of the adapter must be performed prior to calling this function 547 * in order for the MAC address to have been loaded from the EEPROM into RAR0 548 **/ 549 void wx_get_mac_addr(struct wx *wx, u8 *mac_addr) 550 { 551 u32 rar_high; 552 u32 rar_low; 553 u16 i; 554 555 wr32(wx, WX_PSR_MAC_SWC_IDX, 0); 556 rar_high = rd32(wx, WX_PSR_MAC_SWC_AD_H); 557 rar_low = rd32(wx, WX_PSR_MAC_SWC_AD_L); 558 559 for (i = 0; i < 2; i++) 560 mac_addr[i] = (u8)(rar_high >> (1 - i) * 8); 561 562 for (i = 0; i < 4; i++) 563 mac_addr[i + 2] = (u8)(rar_low >> (3 - i) * 8); 564 } 565 EXPORT_SYMBOL(wx_get_mac_addr); 566 567 /** 568 * wx_set_rar - Set Rx address register 569 * @wx: pointer to hardware structure 570 * @index: Receive address register to write 571 * @addr: Address to put into receive address register 572 * @pools: VMDq "set" or "pool" index 573 * @enable_addr: set flag that address is active 574 * 575 * Puts an ethernet address into a receive address register. 576 **/ 577 static int wx_set_rar(struct wx *wx, u32 index, u8 *addr, u64 pools, 578 u32 enable_addr) 579 { 580 u32 rar_entries = wx->mac.num_rar_entries; 581 u32 rar_low, rar_high; 582 583 /* Make sure we are using a valid rar index range */ 584 if (index >= rar_entries) { 585 wx_err(wx, "RAR index %d is out of range.\n", index); 586 return -EINVAL; 587 } 588 589 /* select the MAC address */ 590 wr32(wx, WX_PSR_MAC_SWC_IDX, index); 591 592 /* setup VMDq pool mapping */ 593 wr32(wx, WX_PSR_MAC_SWC_VM_L, pools & 0xFFFFFFFF); 594 if (wx->mac.type == wx_mac_sp) 595 wr32(wx, WX_PSR_MAC_SWC_VM_H, pools >> 32); 596 597 /* HW expects these in little endian so we reverse the byte 598 * order from network order (big endian) to little endian 599 * 600 * Some parts put the VMDq setting in the extra RAH bits, 601 * so save everything except the lower 16 bits that hold part 602 * of the address and the address valid bit. 603 */ 604 rar_low = ((u32)addr[5] | 605 ((u32)addr[4] << 8) | 606 ((u32)addr[3] << 16) | 607 ((u32)addr[2] << 24)); 608 rar_high = ((u32)addr[1] | 609 ((u32)addr[0] << 8)); 610 if (enable_addr != 0) 611 rar_high |= WX_PSR_MAC_SWC_AD_H_AV; 612 613 wr32(wx, WX_PSR_MAC_SWC_AD_L, rar_low); 614 wr32m(wx, WX_PSR_MAC_SWC_AD_H, 615 (WX_PSR_MAC_SWC_AD_H_AD(U16_MAX) | 616 WX_PSR_MAC_SWC_AD_H_ADTYPE(1) | 617 WX_PSR_MAC_SWC_AD_H_AV), 618 rar_high); 619 620 return 0; 621 } 622 623 /** 624 * wx_clear_rar - Remove Rx address register 625 * @wx: pointer to hardware structure 626 * @index: Receive address register to write 627 * 628 * Clears an ethernet address from a receive address register. 629 **/ 630 static int wx_clear_rar(struct wx *wx, u32 index) 631 { 632 u32 rar_entries = wx->mac.num_rar_entries; 633 634 /* Make sure we are using a valid rar index range */ 635 if (index >= rar_entries) { 636 wx_err(wx, "RAR index %d is out of range.\n", index); 637 return -EINVAL; 638 } 639 640 /* Some parts put the VMDq setting in the extra RAH bits, 641 * so save everything except the lower 16 bits that hold part 642 * of the address and the address valid bit. 643 */ 644 wr32(wx, WX_PSR_MAC_SWC_IDX, index); 645 646 wr32(wx, WX_PSR_MAC_SWC_VM_L, 0); 647 wr32(wx, WX_PSR_MAC_SWC_VM_H, 0); 648 649 wr32(wx, WX_PSR_MAC_SWC_AD_L, 0); 650 wr32m(wx, WX_PSR_MAC_SWC_AD_H, 651 (WX_PSR_MAC_SWC_AD_H_AD(U16_MAX) | 652 WX_PSR_MAC_SWC_AD_H_ADTYPE(1) | 653 WX_PSR_MAC_SWC_AD_H_AV), 654 0); 655 656 return 0; 657 } 658 659 /** 660 * wx_clear_vmdq - Disassociate a VMDq pool index from a rx address 661 * @wx: pointer to hardware struct 662 * @rar: receive address register index to disassociate 663 * @vmdq: VMDq pool index to remove from the rar 664 **/ 665 static int wx_clear_vmdq(struct wx *wx, u32 rar, u32 __maybe_unused vmdq) 666 { 667 u32 rar_entries = wx->mac.num_rar_entries; 668 u32 mpsar_lo, mpsar_hi; 669 670 /* Make sure we are using a valid rar index range */ 671 if (rar >= rar_entries) { 672 wx_err(wx, "RAR index %d is out of range.\n", rar); 673 return -EINVAL; 674 } 675 676 wr32(wx, WX_PSR_MAC_SWC_IDX, rar); 677 mpsar_lo = rd32(wx, WX_PSR_MAC_SWC_VM_L); 678 mpsar_hi = rd32(wx, WX_PSR_MAC_SWC_VM_H); 679 680 if (!mpsar_lo && !mpsar_hi) 681 return 0; 682 683 /* was that the last pool using this rar? */ 684 if (mpsar_lo == 0 && mpsar_hi == 0 && rar != 0) 685 wx_clear_rar(wx, rar); 686 687 return 0; 688 } 689 690 /** 691 * wx_init_uta_tables - Initialize the Unicast Table Array 692 * @wx: pointer to hardware structure 693 **/ 694 static void wx_init_uta_tables(struct wx *wx) 695 { 696 int i; 697 698 wx_dbg(wx, " Clearing UTA\n"); 699 700 for (i = 0; i < 128; i++) 701 wr32(wx, WX_PSR_UC_TBL(i), 0); 702 } 703 704 /** 705 * wx_init_rx_addrs - Initializes receive address filters. 706 * @wx: pointer to hardware structure 707 * 708 * Places the MAC address in receive address register 0 and clears the rest 709 * of the receive address registers. Clears the multicast table. Assumes 710 * the receiver is in reset when the routine is called. 711 **/ 712 void wx_init_rx_addrs(struct wx *wx) 713 { 714 u32 rar_entries = wx->mac.num_rar_entries; 715 u32 psrctl; 716 int i; 717 718 /* If the current mac address is valid, assume it is a software override 719 * to the permanent address. 720 * Otherwise, use the permanent address from the eeprom. 721 */ 722 if (!is_valid_ether_addr(wx->mac.addr)) { 723 /* Get the MAC address from the RAR0 for later reference */ 724 wx_get_mac_addr(wx, wx->mac.addr); 725 wx_dbg(wx, "Keeping Current RAR0 Addr = %pM\n", wx->mac.addr); 726 } else { 727 /* Setup the receive address. */ 728 wx_dbg(wx, "Overriding MAC Address in RAR[0]\n"); 729 wx_dbg(wx, "New MAC Addr = %pM\n", wx->mac.addr); 730 731 wx_set_rar(wx, 0, wx->mac.addr, 0, WX_PSR_MAC_SWC_AD_H_AV); 732 733 if (wx->mac.type == wx_mac_sp) { 734 /* clear VMDq pool/queue selection for RAR 0 */ 735 wx_clear_vmdq(wx, 0, WX_CLEAR_VMDQ_ALL); 736 } 737 } 738 739 /* Zero out the other receive addresses. */ 740 wx_dbg(wx, "Clearing RAR[1-%d]\n", rar_entries - 1); 741 for (i = 1; i < rar_entries; i++) { 742 wr32(wx, WX_PSR_MAC_SWC_IDX, i); 743 wr32(wx, WX_PSR_MAC_SWC_AD_L, 0); 744 wr32(wx, WX_PSR_MAC_SWC_AD_H, 0); 745 } 746 747 /* Clear the MTA */ 748 wx->addr_ctrl.mta_in_use = 0; 749 psrctl = rd32(wx, WX_PSR_CTL); 750 psrctl &= ~(WX_PSR_CTL_MO | WX_PSR_CTL_MFE); 751 psrctl |= wx->mac.mc_filter_type << WX_PSR_CTL_MO_SHIFT; 752 wr32(wx, WX_PSR_CTL, psrctl); 753 wx_dbg(wx, " Clearing MTA\n"); 754 for (i = 0; i < wx->mac.mcft_size; i++) 755 wr32(wx, WX_PSR_MC_TBL(i), 0); 756 757 wx_init_uta_tables(wx); 758 } 759 EXPORT_SYMBOL(wx_init_rx_addrs); 760 761 static void wx_sync_mac_table(struct wx *wx) 762 { 763 int i; 764 765 for (i = 0; i < wx->mac.num_rar_entries; i++) { 766 if (wx->mac_table[i].state & WX_MAC_STATE_MODIFIED) { 767 if (wx->mac_table[i].state & WX_MAC_STATE_IN_USE) { 768 wx_set_rar(wx, i, 769 wx->mac_table[i].addr, 770 wx->mac_table[i].pools, 771 WX_PSR_MAC_SWC_AD_H_AV); 772 } else { 773 wx_clear_rar(wx, i); 774 } 775 wx->mac_table[i].state &= ~(WX_MAC_STATE_MODIFIED); 776 } 777 } 778 } 779 780 /* this function destroys the first RAR entry */ 781 void wx_mac_set_default_filter(struct wx *wx, u8 *addr) 782 { 783 memcpy(&wx->mac_table[0].addr, addr, ETH_ALEN); 784 wx->mac_table[0].pools = 1ULL; 785 wx->mac_table[0].state = (WX_MAC_STATE_DEFAULT | WX_MAC_STATE_IN_USE); 786 wx_set_rar(wx, 0, wx->mac_table[0].addr, 787 wx->mac_table[0].pools, 788 WX_PSR_MAC_SWC_AD_H_AV); 789 } 790 EXPORT_SYMBOL(wx_mac_set_default_filter); 791 792 void wx_flush_sw_mac_table(struct wx *wx) 793 { 794 u32 i; 795 796 for (i = 0; i < wx->mac.num_rar_entries; i++) { 797 if (!(wx->mac_table[i].state & WX_MAC_STATE_IN_USE)) 798 continue; 799 800 wx->mac_table[i].state |= WX_MAC_STATE_MODIFIED; 801 wx->mac_table[i].state &= ~WX_MAC_STATE_IN_USE; 802 memset(wx->mac_table[i].addr, 0, ETH_ALEN); 803 wx->mac_table[i].pools = 0; 804 } 805 wx_sync_mac_table(wx); 806 } 807 EXPORT_SYMBOL(wx_flush_sw_mac_table); 808 809 static int wx_add_mac_filter(struct wx *wx, u8 *addr, u16 pool) 810 { 811 u32 i; 812 813 if (is_zero_ether_addr(addr)) 814 return -EINVAL; 815 816 for (i = 0; i < wx->mac.num_rar_entries; i++) { 817 if (wx->mac_table[i].state & WX_MAC_STATE_IN_USE) { 818 if (ether_addr_equal(addr, wx->mac_table[i].addr)) { 819 if (wx->mac_table[i].pools != (1ULL << pool)) { 820 memcpy(wx->mac_table[i].addr, addr, ETH_ALEN); 821 wx->mac_table[i].pools |= (1ULL << pool); 822 wx_sync_mac_table(wx); 823 return i; 824 } 825 } 826 } 827 828 if (wx->mac_table[i].state & WX_MAC_STATE_IN_USE) 829 continue; 830 wx->mac_table[i].state |= (WX_MAC_STATE_MODIFIED | 831 WX_MAC_STATE_IN_USE); 832 memcpy(wx->mac_table[i].addr, addr, ETH_ALEN); 833 wx->mac_table[i].pools |= (1ULL << pool); 834 wx_sync_mac_table(wx); 835 return i; 836 } 837 return -ENOMEM; 838 } 839 840 static int wx_del_mac_filter(struct wx *wx, u8 *addr, u16 pool) 841 { 842 u32 i; 843 844 if (is_zero_ether_addr(addr)) 845 return -EINVAL; 846 847 /* search table for addr, if found, set to 0 and sync */ 848 for (i = 0; i < wx->mac.num_rar_entries; i++) { 849 if (!ether_addr_equal(addr, wx->mac_table[i].addr)) 850 continue; 851 852 wx->mac_table[i].state |= WX_MAC_STATE_MODIFIED; 853 wx->mac_table[i].pools &= ~(1ULL << pool); 854 if (!wx->mac_table[i].pools) { 855 wx->mac_table[i].state &= ~WX_MAC_STATE_IN_USE; 856 memset(wx->mac_table[i].addr, 0, ETH_ALEN); 857 } 858 wx_sync_mac_table(wx); 859 return 0; 860 } 861 return -ENOMEM; 862 } 863 864 static int wx_available_rars(struct wx *wx) 865 { 866 u32 i, count = 0; 867 868 for (i = 0; i < wx->mac.num_rar_entries; i++) { 869 if (wx->mac_table[i].state == 0) 870 count++; 871 } 872 873 return count; 874 } 875 876 /** 877 * wx_write_uc_addr_list - write unicast addresses to RAR table 878 * @netdev: network interface device structure 879 * @pool: index for mac table 880 * 881 * Writes unicast address list to the RAR table. 882 * Returns: -ENOMEM on failure/insufficient address space 883 * 0 on no addresses written 884 * X on writing X addresses to the RAR table 885 **/ 886 static int wx_write_uc_addr_list(struct net_device *netdev, int pool) 887 { 888 struct wx *wx = netdev_priv(netdev); 889 int count = 0; 890 891 /* return ENOMEM indicating insufficient memory for addresses */ 892 if (netdev_uc_count(netdev) > wx_available_rars(wx)) 893 return -ENOMEM; 894 895 if (!netdev_uc_empty(netdev)) { 896 struct netdev_hw_addr *ha; 897 898 netdev_for_each_uc_addr(ha, netdev) { 899 wx_del_mac_filter(wx, ha->addr, pool); 900 wx_add_mac_filter(wx, ha->addr, pool); 901 count++; 902 } 903 } 904 return count; 905 } 906 907 /** 908 * wx_mta_vector - Determines bit-vector in multicast table to set 909 * @wx: pointer to private structure 910 * @mc_addr: the multicast address 911 * 912 * Extracts the 12 bits, from a multicast address, to determine which 913 * bit-vector to set in the multicast table. The hardware uses 12 bits, from 914 * incoming rx multicast addresses, to determine the bit-vector to check in 915 * the MTA. Which of the 4 combination, of 12-bits, the hardware uses is set 916 * by the MO field of the MCSTCTRL. The MO field is set during initialization 917 * to mc_filter_type. 918 **/ 919 static u32 wx_mta_vector(struct wx *wx, u8 *mc_addr) 920 { 921 u32 vector = 0; 922 923 switch (wx->mac.mc_filter_type) { 924 case 0: /* use bits [47:36] of the address */ 925 vector = ((mc_addr[4] >> 4) | (((u16)mc_addr[5]) << 4)); 926 break; 927 case 1: /* use bits [46:35] of the address */ 928 vector = ((mc_addr[4] >> 3) | (((u16)mc_addr[5]) << 5)); 929 break; 930 case 2: /* use bits [45:34] of the address */ 931 vector = ((mc_addr[4] >> 2) | (((u16)mc_addr[5]) << 6)); 932 break; 933 case 3: /* use bits [43:32] of the address */ 934 vector = ((mc_addr[4]) | (((u16)mc_addr[5]) << 8)); 935 break; 936 default: /* Invalid mc_filter_type */ 937 wx_err(wx, "MC filter type param set incorrectly\n"); 938 break; 939 } 940 941 /* vector can only be 12-bits or boundary will be exceeded */ 942 vector &= 0xFFF; 943 return vector; 944 } 945 946 /** 947 * wx_set_mta - Set bit-vector in multicast table 948 * @wx: pointer to private structure 949 * @mc_addr: Multicast address 950 * 951 * Sets the bit-vector in the multicast table. 952 **/ 953 static void wx_set_mta(struct wx *wx, u8 *mc_addr) 954 { 955 u32 vector, vector_bit, vector_reg; 956 957 wx->addr_ctrl.mta_in_use++; 958 959 vector = wx_mta_vector(wx, mc_addr); 960 wx_dbg(wx, " bit-vector = 0x%03X\n", vector); 961 962 /* The MTA is a register array of 128 32-bit registers. It is treated 963 * like an array of 4096 bits. We want to set bit 964 * BitArray[vector_value]. So we figure out what register the bit is 965 * in, read it, OR in the new bit, then write back the new value. The 966 * register is determined by the upper 7 bits of the vector value and 967 * the bit within that register are determined by the lower 5 bits of 968 * the value. 969 */ 970 vector_reg = (vector >> 5) & 0x7F; 971 vector_bit = vector & 0x1F; 972 wx->mac.mta_shadow[vector_reg] |= (1 << vector_bit); 973 } 974 975 /** 976 * wx_update_mc_addr_list - Updates MAC list of multicast addresses 977 * @wx: pointer to private structure 978 * @netdev: pointer to net device structure 979 * 980 * The given list replaces any existing list. Clears the MC addrs from receive 981 * address registers and the multicast table. Uses unused receive address 982 * registers for the first multicast addresses, and hashes the rest into the 983 * multicast table. 984 **/ 985 static void wx_update_mc_addr_list(struct wx *wx, struct net_device *netdev) 986 { 987 struct netdev_hw_addr *ha; 988 u32 i, psrctl; 989 990 /* Set the new number of MC addresses that we are being requested to 991 * use. 992 */ 993 wx->addr_ctrl.num_mc_addrs = netdev_mc_count(netdev); 994 wx->addr_ctrl.mta_in_use = 0; 995 996 /* Clear mta_shadow */ 997 wx_dbg(wx, " Clearing MTA\n"); 998 memset(&wx->mac.mta_shadow, 0, sizeof(wx->mac.mta_shadow)); 999 1000 /* Update mta_shadow */ 1001 netdev_for_each_mc_addr(ha, netdev) { 1002 wx_dbg(wx, " Adding the multicast addresses:\n"); 1003 wx_set_mta(wx, ha->addr); 1004 } 1005 1006 /* Enable mta */ 1007 for (i = 0; i < wx->mac.mcft_size; i++) 1008 wr32a(wx, WX_PSR_MC_TBL(0), i, 1009 wx->mac.mta_shadow[i]); 1010 1011 if (wx->addr_ctrl.mta_in_use > 0) { 1012 psrctl = rd32(wx, WX_PSR_CTL); 1013 psrctl &= ~(WX_PSR_CTL_MO | WX_PSR_CTL_MFE); 1014 psrctl |= WX_PSR_CTL_MFE | 1015 (wx->mac.mc_filter_type << WX_PSR_CTL_MO_SHIFT); 1016 wr32(wx, WX_PSR_CTL, psrctl); 1017 } 1018 1019 wx_dbg(wx, "Update mc addr list Complete\n"); 1020 } 1021 1022 /** 1023 * wx_write_mc_addr_list - write multicast addresses to MTA 1024 * @netdev: network interface device structure 1025 * 1026 * Writes multicast address list to the MTA hash table. 1027 * Returns: 0 on no addresses written 1028 * X on writing X addresses to MTA 1029 **/ 1030 static int wx_write_mc_addr_list(struct net_device *netdev) 1031 { 1032 struct wx *wx = netdev_priv(netdev); 1033 1034 if (!netif_running(netdev)) 1035 return 0; 1036 1037 wx_update_mc_addr_list(wx, netdev); 1038 1039 return netdev_mc_count(netdev); 1040 } 1041 1042 /** 1043 * wx_set_mac - Change the Ethernet Address of the NIC 1044 * @netdev: network interface device structure 1045 * @p: pointer to an address structure 1046 * 1047 * Returns 0 on success, negative on failure 1048 **/ 1049 int wx_set_mac(struct net_device *netdev, void *p) 1050 { 1051 struct wx *wx = netdev_priv(netdev); 1052 struct sockaddr *addr = p; 1053 int retval; 1054 1055 retval = eth_prepare_mac_addr_change(netdev, addr); 1056 if (retval) 1057 return retval; 1058 1059 wx_del_mac_filter(wx, wx->mac.addr, 0); 1060 eth_hw_addr_set(netdev, addr->sa_data); 1061 memcpy(wx->mac.addr, addr->sa_data, netdev->addr_len); 1062 1063 wx_mac_set_default_filter(wx, wx->mac.addr); 1064 1065 return 0; 1066 } 1067 EXPORT_SYMBOL(wx_set_mac); 1068 1069 void wx_disable_rx(struct wx *wx) 1070 { 1071 u32 pfdtxgswc; 1072 u32 rxctrl; 1073 1074 rxctrl = rd32(wx, WX_RDB_PB_CTL); 1075 if (rxctrl & WX_RDB_PB_CTL_RXEN) { 1076 pfdtxgswc = rd32(wx, WX_PSR_CTL); 1077 if (pfdtxgswc & WX_PSR_CTL_SW_EN) { 1078 pfdtxgswc &= ~WX_PSR_CTL_SW_EN; 1079 wr32(wx, WX_PSR_CTL, pfdtxgswc); 1080 wx->mac.set_lben = true; 1081 } else { 1082 wx->mac.set_lben = false; 1083 } 1084 rxctrl &= ~WX_RDB_PB_CTL_RXEN; 1085 wr32(wx, WX_RDB_PB_CTL, rxctrl); 1086 1087 if (!(((wx->subsystem_device_id & WX_NCSI_MASK) == WX_NCSI_SUP) || 1088 ((wx->subsystem_device_id & WX_WOL_MASK) == WX_WOL_SUP))) { 1089 /* disable mac receiver */ 1090 wr32m(wx, WX_MAC_RX_CFG, 1091 WX_MAC_RX_CFG_RE, 0); 1092 } 1093 } 1094 } 1095 EXPORT_SYMBOL(wx_disable_rx); 1096 1097 static void wx_enable_rx(struct wx *wx) 1098 { 1099 u32 psrctl; 1100 1101 /* enable mac receiver */ 1102 wr32m(wx, WX_MAC_RX_CFG, 1103 WX_MAC_RX_CFG_RE, WX_MAC_RX_CFG_RE); 1104 1105 wr32m(wx, WX_RDB_PB_CTL, 1106 WX_RDB_PB_CTL_RXEN, WX_RDB_PB_CTL_RXEN); 1107 1108 if (wx->mac.set_lben) { 1109 psrctl = rd32(wx, WX_PSR_CTL); 1110 psrctl |= WX_PSR_CTL_SW_EN; 1111 wr32(wx, WX_PSR_CTL, psrctl); 1112 wx->mac.set_lben = false; 1113 } 1114 } 1115 1116 /** 1117 * wx_set_rxpba - Initialize Rx packet buffer 1118 * @wx: pointer to private structure 1119 **/ 1120 static void wx_set_rxpba(struct wx *wx) 1121 { 1122 u32 rxpktsize, txpktsize, txpbthresh; 1123 1124 rxpktsize = wx->mac.rx_pb_size << WX_RDB_PB_SZ_SHIFT; 1125 wr32(wx, WX_RDB_PB_SZ(0), rxpktsize); 1126 1127 /* Only support an equally distributed Tx packet buffer strategy. */ 1128 txpktsize = wx->mac.tx_pb_size; 1129 txpbthresh = (txpktsize / 1024) - WX_TXPKT_SIZE_MAX; 1130 wr32(wx, WX_TDB_PB_SZ(0), txpktsize); 1131 wr32(wx, WX_TDM_PB_THRE(0), txpbthresh); 1132 } 1133 1134 static void wx_configure_port(struct wx *wx) 1135 { 1136 u32 value, i; 1137 1138 value = WX_CFG_PORT_CTL_D_VLAN | WX_CFG_PORT_CTL_QINQ; 1139 wr32m(wx, WX_CFG_PORT_CTL, 1140 WX_CFG_PORT_CTL_D_VLAN | 1141 WX_CFG_PORT_CTL_QINQ, 1142 value); 1143 1144 wr32(wx, WX_CFG_TAG_TPID(0), 1145 ETH_P_8021Q | ETH_P_8021AD << 16); 1146 wx->tpid[0] = ETH_P_8021Q; 1147 wx->tpid[1] = ETH_P_8021AD; 1148 for (i = 1; i < 4; i++) 1149 wr32(wx, WX_CFG_TAG_TPID(i), 1150 ETH_P_8021Q | ETH_P_8021Q << 16); 1151 for (i = 2; i < 8; i++) 1152 wx->tpid[i] = ETH_P_8021Q; 1153 } 1154 1155 /** 1156 * wx_disable_sec_rx_path - Stops the receive data path 1157 * @wx: pointer to private structure 1158 * 1159 * Stops the receive data path and waits for the HW to internally empty 1160 * the Rx security block 1161 **/ 1162 static int wx_disable_sec_rx_path(struct wx *wx) 1163 { 1164 u32 secrx; 1165 1166 wr32m(wx, WX_RSC_CTL, 1167 WX_RSC_CTL_RX_DIS, WX_RSC_CTL_RX_DIS); 1168 1169 return read_poll_timeout(rd32, secrx, secrx & WX_RSC_ST_RSEC_RDY, 1170 1000, 40000, false, wx, WX_RSC_ST); 1171 } 1172 1173 /** 1174 * wx_enable_sec_rx_path - Enables the receive data path 1175 * @wx: pointer to private structure 1176 * 1177 * Enables the receive data path. 1178 **/ 1179 static void wx_enable_sec_rx_path(struct wx *wx) 1180 { 1181 wr32m(wx, WX_RSC_CTL, WX_RSC_CTL_RX_DIS, 0); 1182 WX_WRITE_FLUSH(wx); 1183 } 1184 1185 static void wx_vlan_strip_control(struct wx *wx, bool enable) 1186 { 1187 int i, j; 1188 1189 for (i = 0; i < wx->num_rx_queues; i++) { 1190 struct wx_ring *ring = wx->rx_ring[i]; 1191 1192 j = ring->reg_idx; 1193 wr32m(wx, WX_PX_RR_CFG(j), WX_PX_RR_CFG_VLAN, 1194 enable ? WX_PX_RR_CFG_VLAN : 0); 1195 } 1196 } 1197 1198 void wx_set_rx_mode(struct net_device *netdev) 1199 { 1200 struct wx *wx = netdev_priv(netdev); 1201 netdev_features_t features; 1202 u32 fctrl, vmolr, vlnctrl; 1203 int count; 1204 1205 features = netdev->features; 1206 1207 /* Check for Promiscuous and All Multicast modes */ 1208 fctrl = rd32(wx, WX_PSR_CTL); 1209 fctrl &= ~(WX_PSR_CTL_UPE | WX_PSR_CTL_MPE); 1210 vmolr = rd32(wx, WX_PSR_VM_L2CTL(0)); 1211 vmolr &= ~(WX_PSR_VM_L2CTL_UPE | 1212 WX_PSR_VM_L2CTL_MPE | 1213 WX_PSR_VM_L2CTL_ROPE | 1214 WX_PSR_VM_L2CTL_ROMPE); 1215 vlnctrl = rd32(wx, WX_PSR_VLAN_CTL); 1216 vlnctrl &= ~(WX_PSR_VLAN_CTL_VFE | WX_PSR_VLAN_CTL_CFIEN); 1217 1218 /* set all bits that we expect to always be set */ 1219 fctrl |= WX_PSR_CTL_BAM | WX_PSR_CTL_MFE; 1220 vmolr |= WX_PSR_VM_L2CTL_BAM | 1221 WX_PSR_VM_L2CTL_AUPE | 1222 WX_PSR_VM_L2CTL_VACC; 1223 vlnctrl |= WX_PSR_VLAN_CTL_VFE; 1224 1225 wx->addr_ctrl.user_set_promisc = false; 1226 if (netdev->flags & IFF_PROMISC) { 1227 wx->addr_ctrl.user_set_promisc = true; 1228 fctrl |= WX_PSR_CTL_UPE | WX_PSR_CTL_MPE; 1229 /* pf don't want packets routing to vf, so clear UPE */ 1230 vmolr |= WX_PSR_VM_L2CTL_MPE; 1231 vlnctrl &= ~WX_PSR_VLAN_CTL_VFE; 1232 } 1233 1234 if (netdev->flags & IFF_ALLMULTI) { 1235 fctrl |= WX_PSR_CTL_MPE; 1236 vmolr |= WX_PSR_VM_L2CTL_MPE; 1237 } 1238 1239 if (netdev->features & NETIF_F_RXALL) { 1240 vmolr |= (WX_PSR_VM_L2CTL_UPE | WX_PSR_VM_L2CTL_MPE); 1241 vlnctrl &= ~WX_PSR_VLAN_CTL_VFE; 1242 /* receive bad packets */ 1243 wr32m(wx, WX_RSC_CTL, 1244 WX_RSC_CTL_SAVE_MAC_ERR, 1245 WX_RSC_CTL_SAVE_MAC_ERR); 1246 } else { 1247 vmolr |= WX_PSR_VM_L2CTL_ROPE | WX_PSR_VM_L2CTL_ROMPE; 1248 } 1249 1250 /* Write addresses to available RAR registers, if there is not 1251 * sufficient space to store all the addresses then enable 1252 * unicast promiscuous mode 1253 */ 1254 count = wx_write_uc_addr_list(netdev, 0); 1255 if (count < 0) { 1256 vmolr &= ~WX_PSR_VM_L2CTL_ROPE; 1257 vmolr |= WX_PSR_VM_L2CTL_UPE; 1258 } 1259 1260 /* Write addresses to the MTA, if the attempt fails 1261 * then we should just turn on promiscuous mode so 1262 * that we can at least receive multicast traffic 1263 */ 1264 count = wx_write_mc_addr_list(netdev); 1265 if (count < 0) { 1266 vmolr &= ~WX_PSR_VM_L2CTL_ROMPE; 1267 vmolr |= WX_PSR_VM_L2CTL_MPE; 1268 } 1269 1270 wr32(wx, WX_PSR_VLAN_CTL, vlnctrl); 1271 wr32(wx, WX_PSR_CTL, fctrl); 1272 wr32(wx, WX_PSR_VM_L2CTL(0), vmolr); 1273 1274 if ((features & NETIF_F_HW_VLAN_CTAG_RX) && 1275 (features & NETIF_F_HW_VLAN_STAG_RX)) 1276 wx_vlan_strip_control(wx, true); 1277 else 1278 wx_vlan_strip_control(wx, false); 1279 1280 } 1281 EXPORT_SYMBOL(wx_set_rx_mode); 1282 1283 static void wx_set_rx_buffer_len(struct wx *wx) 1284 { 1285 struct net_device *netdev = wx->netdev; 1286 u32 mhadd, max_frame; 1287 1288 max_frame = netdev->mtu + ETH_HLEN + ETH_FCS_LEN + VLAN_HLEN; 1289 /* adjust max frame to be at least the size of a standard frame */ 1290 if (max_frame < (ETH_FRAME_LEN + ETH_FCS_LEN)) 1291 max_frame = (ETH_FRAME_LEN + ETH_FCS_LEN); 1292 1293 mhadd = rd32(wx, WX_PSR_MAX_SZ); 1294 if (max_frame != mhadd) 1295 wr32(wx, WX_PSR_MAX_SZ, max_frame); 1296 } 1297 1298 /** 1299 * wx_change_mtu - Change the Maximum Transfer Unit 1300 * @netdev: network interface device structure 1301 * @new_mtu: new value for maximum frame size 1302 * 1303 * Returns 0 on success, negative on failure 1304 **/ 1305 int wx_change_mtu(struct net_device *netdev, int new_mtu) 1306 { 1307 struct wx *wx = netdev_priv(netdev); 1308 1309 netdev->mtu = new_mtu; 1310 wx_set_rx_buffer_len(wx); 1311 1312 return 0; 1313 } 1314 EXPORT_SYMBOL(wx_change_mtu); 1315 1316 /* Disable the specified rx queue */ 1317 void wx_disable_rx_queue(struct wx *wx, struct wx_ring *ring) 1318 { 1319 u8 reg_idx = ring->reg_idx; 1320 u32 rxdctl; 1321 int ret; 1322 1323 /* write value back with RRCFG.EN bit cleared */ 1324 wr32m(wx, WX_PX_RR_CFG(reg_idx), 1325 WX_PX_RR_CFG_RR_EN, 0); 1326 1327 /* the hardware may take up to 100us to really disable the rx queue */ 1328 ret = read_poll_timeout(rd32, rxdctl, !(rxdctl & WX_PX_RR_CFG_RR_EN), 1329 10, 100, true, wx, WX_PX_RR_CFG(reg_idx)); 1330 1331 if (ret == -ETIMEDOUT) { 1332 /* Just for information */ 1333 wx_err(wx, 1334 "RRCFG.EN on Rx queue %d not cleared within the polling period\n", 1335 reg_idx); 1336 } 1337 } 1338 EXPORT_SYMBOL(wx_disable_rx_queue); 1339 1340 static void wx_enable_rx_queue(struct wx *wx, struct wx_ring *ring) 1341 { 1342 u8 reg_idx = ring->reg_idx; 1343 u32 rxdctl; 1344 int ret; 1345 1346 ret = read_poll_timeout(rd32, rxdctl, rxdctl & WX_PX_RR_CFG_RR_EN, 1347 1000, 10000, true, wx, WX_PX_RR_CFG(reg_idx)); 1348 1349 if (ret == -ETIMEDOUT) { 1350 /* Just for information */ 1351 wx_err(wx, 1352 "RRCFG.EN on Rx queue %d not set within the polling period\n", 1353 reg_idx); 1354 } 1355 } 1356 1357 static void wx_configure_srrctl(struct wx *wx, 1358 struct wx_ring *rx_ring) 1359 { 1360 u16 reg_idx = rx_ring->reg_idx; 1361 u32 srrctl; 1362 1363 srrctl = rd32(wx, WX_PX_RR_CFG(reg_idx)); 1364 srrctl &= ~(WX_PX_RR_CFG_RR_HDR_SZ | 1365 WX_PX_RR_CFG_RR_BUF_SZ | 1366 WX_PX_RR_CFG_SPLIT_MODE); 1367 /* configure header buffer length, needed for RSC */ 1368 srrctl |= WX_RXBUFFER_256 << WX_PX_RR_CFG_BHDRSIZE_SHIFT; 1369 1370 /* configure the packet buffer length */ 1371 srrctl |= WX_RX_BUFSZ >> WX_PX_RR_CFG_BSIZEPKT_SHIFT; 1372 1373 wr32(wx, WX_PX_RR_CFG(reg_idx), srrctl); 1374 } 1375 1376 static void wx_configure_tx_ring(struct wx *wx, 1377 struct wx_ring *ring) 1378 { 1379 u32 txdctl = WX_PX_TR_CFG_ENABLE; 1380 u8 reg_idx = ring->reg_idx; 1381 u64 tdba = ring->dma; 1382 int ret; 1383 1384 /* disable queue to avoid issues while updating state */ 1385 wr32(wx, WX_PX_TR_CFG(reg_idx), WX_PX_TR_CFG_SWFLSH); 1386 WX_WRITE_FLUSH(wx); 1387 1388 wr32(wx, WX_PX_TR_BAL(reg_idx), tdba & DMA_BIT_MASK(32)); 1389 wr32(wx, WX_PX_TR_BAH(reg_idx), upper_32_bits(tdba)); 1390 1391 /* reset head and tail pointers */ 1392 wr32(wx, WX_PX_TR_RP(reg_idx), 0); 1393 wr32(wx, WX_PX_TR_WP(reg_idx), 0); 1394 ring->tail = wx->hw_addr + WX_PX_TR_WP(reg_idx); 1395 1396 if (ring->count < WX_MAX_TXD) 1397 txdctl |= ring->count / 128 << WX_PX_TR_CFG_TR_SIZE_SHIFT; 1398 txdctl |= 0x20 << WX_PX_TR_CFG_WTHRESH_SHIFT; 1399 1400 /* reinitialize tx_buffer_info */ 1401 memset(ring->tx_buffer_info, 0, 1402 sizeof(struct wx_tx_buffer) * ring->count); 1403 1404 /* enable queue */ 1405 wr32(wx, WX_PX_TR_CFG(reg_idx), txdctl); 1406 1407 /* poll to verify queue is enabled */ 1408 ret = read_poll_timeout(rd32, txdctl, txdctl & WX_PX_TR_CFG_ENABLE, 1409 1000, 10000, true, wx, WX_PX_TR_CFG(reg_idx)); 1410 if (ret == -ETIMEDOUT) 1411 wx_err(wx, "Could not enable Tx Queue %d\n", reg_idx); 1412 } 1413 1414 static void wx_configure_rx_ring(struct wx *wx, 1415 struct wx_ring *ring) 1416 { 1417 u16 reg_idx = ring->reg_idx; 1418 union wx_rx_desc *rx_desc; 1419 u64 rdba = ring->dma; 1420 u32 rxdctl; 1421 1422 /* disable queue to avoid issues while updating state */ 1423 rxdctl = rd32(wx, WX_PX_RR_CFG(reg_idx)); 1424 wx_disable_rx_queue(wx, ring); 1425 1426 wr32(wx, WX_PX_RR_BAL(reg_idx), rdba & DMA_BIT_MASK(32)); 1427 wr32(wx, WX_PX_RR_BAH(reg_idx), upper_32_bits(rdba)); 1428 1429 if (ring->count == WX_MAX_RXD) 1430 rxdctl |= 0 << WX_PX_RR_CFG_RR_SIZE_SHIFT; 1431 else 1432 rxdctl |= (ring->count / 128) << WX_PX_RR_CFG_RR_SIZE_SHIFT; 1433 1434 rxdctl |= 0x1 << WX_PX_RR_CFG_RR_THER_SHIFT; 1435 wr32(wx, WX_PX_RR_CFG(reg_idx), rxdctl); 1436 1437 /* reset head and tail pointers */ 1438 wr32(wx, WX_PX_RR_RP(reg_idx), 0); 1439 wr32(wx, WX_PX_RR_WP(reg_idx), 0); 1440 ring->tail = wx->hw_addr + WX_PX_RR_WP(reg_idx); 1441 1442 wx_configure_srrctl(wx, ring); 1443 1444 /* initialize rx_buffer_info */ 1445 memset(ring->rx_buffer_info, 0, 1446 sizeof(struct wx_rx_buffer) * ring->count); 1447 1448 /* initialize Rx descriptor 0 */ 1449 rx_desc = WX_RX_DESC(ring, 0); 1450 rx_desc->wb.upper.length = 0; 1451 1452 /* enable receive descriptor ring */ 1453 wr32m(wx, WX_PX_RR_CFG(reg_idx), 1454 WX_PX_RR_CFG_RR_EN, WX_PX_RR_CFG_RR_EN); 1455 1456 wx_enable_rx_queue(wx, ring); 1457 wx_alloc_rx_buffers(ring, wx_desc_unused(ring)); 1458 } 1459 1460 /** 1461 * wx_configure_tx - Configure Transmit Unit after Reset 1462 * @wx: pointer to private structure 1463 * 1464 * Configure the Tx unit of the MAC after a reset. 1465 **/ 1466 static void wx_configure_tx(struct wx *wx) 1467 { 1468 u32 i; 1469 1470 /* TDM_CTL.TE must be before Tx queues are enabled */ 1471 wr32m(wx, WX_TDM_CTL, 1472 WX_TDM_CTL_TE, WX_TDM_CTL_TE); 1473 1474 /* Setup the HW Tx Head and Tail descriptor pointers */ 1475 for (i = 0; i < wx->num_tx_queues; i++) 1476 wx_configure_tx_ring(wx, wx->tx_ring[i]); 1477 1478 wr32m(wx, WX_TSC_BUF_AE, WX_TSC_BUF_AE_THR, 0x10); 1479 1480 if (wx->mac.type == wx_mac_em) 1481 wr32m(wx, WX_TSC_CTL, WX_TSC_CTL_TX_DIS | WX_TSC_CTL_TSEC_DIS, 0x1); 1482 1483 /* enable mac transmitter */ 1484 wr32m(wx, WX_MAC_TX_CFG, 1485 WX_MAC_TX_CFG_TE, WX_MAC_TX_CFG_TE); 1486 } 1487 1488 static void wx_restore_vlan(struct wx *wx) 1489 { 1490 u16 vid = 1; 1491 1492 wx_vlan_rx_add_vid(wx->netdev, htons(ETH_P_8021Q), 0); 1493 1494 for_each_set_bit_from(vid, wx->active_vlans, VLAN_N_VID) 1495 wx_vlan_rx_add_vid(wx->netdev, htons(ETH_P_8021Q), vid); 1496 } 1497 1498 /** 1499 * wx_configure_rx - Configure Receive Unit after Reset 1500 * @wx: pointer to private structure 1501 * 1502 * Configure the Rx unit of the MAC after a reset. 1503 **/ 1504 static void wx_configure_rx(struct wx *wx) 1505 { 1506 u32 psrtype, i; 1507 int ret; 1508 1509 wx_disable_rx(wx); 1510 1511 psrtype = WX_RDB_PL_CFG_L4HDR | 1512 WX_RDB_PL_CFG_L3HDR | 1513 WX_RDB_PL_CFG_L2HDR | 1514 WX_RDB_PL_CFG_TUN_TUNHDR | 1515 WX_RDB_PL_CFG_TUN_TUNHDR; 1516 wr32(wx, WX_RDB_PL_CFG(0), psrtype); 1517 1518 /* enable hw crc stripping */ 1519 wr32m(wx, WX_RSC_CTL, WX_RSC_CTL_CRC_STRIP, WX_RSC_CTL_CRC_STRIP); 1520 1521 if (wx->mac.type == wx_mac_sp) { 1522 u32 psrctl; 1523 1524 /* RSC Setup */ 1525 psrctl = rd32(wx, WX_PSR_CTL); 1526 psrctl |= WX_PSR_CTL_RSC_ACK; /* Disable RSC for ACK packets */ 1527 psrctl |= WX_PSR_CTL_RSC_DIS; 1528 wr32(wx, WX_PSR_CTL, psrctl); 1529 } 1530 1531 /* set_rx_buffer_len must be called before ring initialization */ 1532 wx_set_rx_buffer_len(wx); 1533 1534 /* Setup the HW Rx Head and Tail Descriptor Pointers and 1535 * the Base and Length of the Rx Descriptor Ring 1536 */ 1537 for (i = 0; i < wx->num_rx_queues; i++) 1538 wx_configure_rx_ring(wx, wx->rx_ring[i]); 1539 1540 /* Enable all receives, disable security engine prior to block traffic */ 1541 ret = wx_disable_sec_rx_path(wx); 1542 if (ret < 0) 1543 wx_err(wx, "The register status is abnormal, please check device."); 1544 1545 wx_enable_rx(wx); 1546 wx_enable_sec_rx_path(wx); 1547 } 1548 1549 static void wx_configure_isb(struct wx *wx) 1550 { 1551 /* set ISB Address */ 1552 wr32(wx, WX_PX_ISB_ADDR_L, wx->isb_dma & DMA_BIT_MASK(32)); 1553 if (IS_ENABLED(CONFIG_ARCH_DMA_ADDR_T_64BIT)) 1554 wr32(wx, WX_PX_ISB_ADDR_H, upper_32_bits(wx->isb_dma)); 1555 } 1556 1557 void wx_configure(struct wx *wx) 1558 { 1559 wx_set_rxpba(wx); 1560 wx_configure_port(wx); 1561 1562 wx_set_rx_mode(wx->netdev); 1563 wx_restore_vlan(wx); 1564 wx_enable_sec_rx_path(wx); 1565 1566 wx_configure_tx(wx); 1567 wx_configure_rx(wx); 1568 wx_configure_isb(wx); 1569 } 1570 EXPORT_SYMBOL(wx_configure); 1571 1572 /** 1573 * wx_disable_pcie_master - Disable PCI-express master access 1574 * @wx: pointer to hardware structure 1575 * 1576 * Disables PCI-Express master access and verifies there are no pending 1577 * requests. 1578 **/ 1579 int wx_disable_pcie_master(struct wx *wx) 1580 { 1581 int status = 0; 1582 u32 val; 1583 1584 /* Always set this bit to ensure any future transactions are blocked */ 1585 pci_clear_master(wx->pdev); 1586 1587 /* Exit if master requests are blocked */ 1588 if (!(rd32(wx, WX_PX_TRANSACTION_PENDING))) 1589 return 0; 1590 1591 /* Poll for master request bit to clear */ 1592 status = read_poll_timeout(rd32, val, !val, 100, WX_PCI_MASTER_DISABLE_TIMEOUT, 1593 false, wx, WX_PX_TRANSACTION_PENDING); 1594 if (status < 0) 1595 wx_err(wx, "PCIe transaction pending bit did not clear.\n"); 1596 1597 return status; 1598 } 1599 EXPORT_SYMBOL(wx_disable_pcie_master); 1600 1601 /** 1602 * wx_stop_adapter - Generic stop Tx/Rx units 1603 * @wx: pointer to hardware structure 1604 * 1605 * Sets the adapter_stopped flag within wx_hw struct. Clears interrupts, 1606 * disables transmit and receive units. The adapter_stopped flag is used by 1607 * the shared code and drivers to determine if the adapter is in a stopped 1608 * state and should not touch the hardware. 1609 **/ 1610 int wx_stop_adapter(struct wx *wx) 1611 { 1612 u16 i; 1613 1614 /* Set the adapter_stopped flag so other driver functions stop touching 1615 * the hardware 1616 */ 1617 wx->adapter_stopped = true; 1618 1619 /* Disable the receive unit */ 1620 wx_disable_rx(wx); 1621 1622 /* Set interrupt mask to stop interrupts from being generated */ 1623 wx_intr_disable(wx, WX_INTR_ALL); 1624 1625 /* Clear any pending interrupts, flush previous writes */ 1626 wr32(wx, WX_PX_MISC_IC, 0xffffffff); 1627 wr32(wx, WX_BME_CTL, 0x3); 1628 1629 /* Disable the transmit unit. Each queue must be disabled. */ 1630 for (i = 0; i < wx->mac.max_tx_queues; i++) { 1631 wr32m(wx, WX_PX_TR_CFG(i), 1632 WX_PX_TR_CFG_SWFLSH | WX_PX_TR_CFG_ENABLE, 1633 WX_PX_TR_CFG_SWFLSH); 1634 } 1635 1636 /* Disable the receive unit by stopping each queue */ 1637 for (i = 0; i < wx->mac.max_rx_queues; i++) { 1638 wr32m(wx, WX_PX_RR_CFG(i), 1639 WX_PX_RR_CFG_RR_EN, 0); 1640 } 1641 1642 /* flush all queues disables */ 1643 WX_WRITE_FLUSH(wx); 1644 1645 /* Prevent the PCI-E bus from hanging by disabling PCI-E master 1646 * access and verify no pending requests 1647 */ 1648 return wx_disable_pcie_master(wx); 1649 } 1650 EXPORT_SYMBOL(wx_stop_adapter); 1651 1652 void wx_reset_misc(struct wx *wx) 1653 { 1654 int i; 1655 1656 /* receive packets that size > 2048 */ 1657 wr32m(wx, WX_MAC_RX_CFG, WX_MAC_RX_CFG_JE, WX_MAC_RX_CFG_JE); 1658 1659 /* clear counters on read */ 1660 wr32m(wx, WX_MMC_CONTROL, 1661 WX_MMC_CONTROL_RSTONRD, WX_MMC_CONTROL_RSTONRD); 1662 1663 wr32m(wx, WX_MAC_RX_FLOW_CTRL, 1664 WX_MAC_RX_FLOW_CTRL_RFE, WX_MAC_RX_FLOW_CTRL_RFE); 1665 1666 wr32(wx, WX_MAC_PKT_FLT, WX_MAC_PKT_FLT_PR); 1667 1668 wr32m(wx, WX_MIS_RST_ST, 1669 WX_MIS_RST_ST_RST_INIT, 0x1E00); 1670 1671 /* errata 4: initialize mng flex tbl and wakeup flex tbl*/ 1672 wr32(wx, WX_PSR_MNG_FLEX_SEL, 0); 1673 for (i = 0; i < 16; i++) { 1674 wr32(wx, WX_PSR_MNG_FLEX_DW_L(i), 0); 1675 wr32(wx, WX_PSR_MNG_FLEX_DW_H(i), 0); 1676 wr32(wx, WX_PSR_MNG_FLEX_MSK(i), 0); 1677 } 1678 wr32(wx, WX_PSR_LAN_FLEX_SEL, 0); 1679 for (i = 0; i < 16; i++) { 1680 wr32(wx, WX_PSR_LAN_FLEX_DW_L(i), 0); 1681 wr32(wx, WX_PSR_LAN_FLEX_DW_H(i), 0); 1682 wr32(wx, WX_PSR_LAN_FLEX_MSK(i), 0); 1683 } 1684 1685 /* set pause frame dst mac addr */ 1686 wr32(wx, WX_RDB_PFCMACDAL, 0xC2000001); 1687 wr32(wx, WX_RDB_PFCMACDAH, 0x0180); 1688 } 1689 EXPORT_SYMBOL(wx_reset_misc); 1690 1691 /** 1692 * wx_get_pcie_msix_counts - Gets MSI-X vector count 1693 * @wx: pointer to hardware structure 1694 * @msix_count: number of MSI interrupts that can be obtained 1695 * @max_msix_count: number of MSI interrupts that mac need 1696 * 1697 * Read PCIe configuration space, and get the MSI-X vector count from 1698 * the capabilities table. 1699 **/ 1700 int wx_get_pcie_msix_counts(struct wx *wx, u16 *msix_count, u16 max_msix_count) 1701 { 1702 struct pci_dev *pdev = wx->pdev; 1703 struct device *dev = &pdev->dev; 1704 int pos; 1705 1706 *msix_count = 1; 1707 pos = pci_find_capability(pdev, PCI_CAP_ID_MSIX); 1708 if (!pos) { 1709 dev_err(dev, "Unable to find MSI-X Capabilities\n"); 1710 return -EINVAL; 1711 } 1712 pci_read_config_word(pdev, 1713 pos + PCI_MSIX_FLAGS, 1714 msix_count); 1715 *msix_count &= WX_PCIE_MSIX_TBL_SZ_MASK; 1716 /* MSI-X count is zero-based in HW */ 1717 *msix_count += 1; 1718 1719 if (*msix_count > max_msix_count) 1720 *msix_count = max_msix_count; 1721 1722 return 0; 1723 } 1724 EXPORT_SYMBOL(wx_get_pcie_msix_counts); 1725 1726 int wx_sw_init(struct wx *wx) 1727 { 1728 struct pci_dev *pdev = wx->pdev; 1729 u32 ssid = 0; 1730 int err = 0; 1731 1732 wx->vendor_id = pdev->vendor; 1733 wx->device_id = pdev->device; 1734 wx->revision_id = pdev->revision; 1735 wx->oem_svid = pdev->subsystem_vendor; 1736 wx->oem_ssid = pdev->subsystem_device; 1737 wx->bus.device = PCI_SLOT(pdev->devfn); 1738 wx->bus.func = PCI_FUNC(pdev->devfn); 1739 1740 if (wx->oem_svid == PCI_VENDOR_ID_WANGXUN) { 1741 wx->subsystem_vendor_id = pdev->subsystem_vendor; 1742 wx->subsystem_device_id = pdev->subsystem_device; 1743 } else { 1744 err = wx_flash_read_dword(wx, 0xfffdc, &ssid); 1745 if (!err) 1746 wx->subsystem_device_id = swab16((u16)ssid); 1747 1748 return err; 1749 } 1750 1751 wx->mac_table = kcalloc(wx->mac.num_rar_entries, 1752 sizeof(struct wx_mac_addr), 1753 GFP_KERNEL); 1754 if (!wx->mac_table) { 1755 wx_err(wx, "mac_table allocation failed\n"); 1756 return -ENOMEM; 1757 } 1758 1759 return 0; 1760 } 1761 EXPORT_SYMBOL(wx_sw_init); 1762 1763 /** 1764 * wx_find_vlvf_slot - find the vlanid or the first empty slot 1765 * @wx: pointer to hardware structure 1766 * @vlan: VLAN id to write to VLAN filter 1767 * 1768 * return the VLVF index where this VLAN id should be placed 1769 * 1770 **/ 1771 static int wx_find_vlvf_slot(struct wx *wx, u32 vlan) 1772 { 1773 u32 bits = 0, first_empty_slot = 0; 1774 int regindex; 1775 1776 /* short cut the special case */ 1777 if (vlan == 0) 1778 return 0; 1779 1780 /* Search for the vlan id in the VLVF entries. Save off the first empty 1781 * slot found along the way 1782 */ 1783 for (regindex = 1; regindex < WX_PSR_VLAN_SWC_ENTRIES; regindex++) { 1784 wr32(wx, WX_PSR_VLAN_SWC_IDX, regindex); 1785 bits = rd32(wx, WX_PSR_VLAN_SWC); 1786 if (!bits && !(first_empty_slot)) 1787 first_empty_slot = regindex; 1788 else if ((bits & 0x0FFF) == vlan) 1789 break; 1790 } 1791 1792 if (regindex >= WX_PSR_VLAN_SWC_ENTRIES) { 1793 if (first_empty_slot) 1794 regindex = first_empty_slot; 1795 else 1796 regindex = -ENOMEM; 1797 } 1798 1799 return regindex; 1800 } 1801 1802 /** 1803 * wx_set_vlvf - Set VLAN Pool Filter 1804 * @wx: pointer to hardware structure 1805 * @vlan: VLAN id to write to VLAN filter 1806 * @vind: VMDq output index that maps queue to VLAN id in VFVFB 1807 * @vlan_on: boolean flag to turn on/off VLAN in VFVF 1808 * @vfta_changed: pointer to boolean flag which indicates whether VFTA 1809 * should be changed 1810 * 1811 * Turn on/off specified bit in VLVF table. 1812 **/ 1813 static int wx_set_vlvf(struct wx *wx, u32 vlan, u32 vind, bool vlan_on, 1814 bool *vfta_changed) 1815 { 1816 int vlvf_index; 1817 u32 vt, bits; 1818 1819 /* If VT Mode is set 1820 * Either vlan_on 1821 * make sure the vlan is in VLVF 1822 * set the vind bit in the matching VLVFB 1823 * Or !vlan_on 1824 * clear the pool bit and possibly the vind 1825 */ 1826 vt = rd32(wx, WX_CFG_PORT_CTL); 1827 if (!(vt & WX_CFG_PORT_CTL_NUM_VT_MASK)) 1828 return 0; 1829 1830 vlvf_index = wx_find_vlvf_slot(wx, vlan); 1831 if (vlvf_index < 0) 1832 return vlvf_index; 1833 1834 wr32(wx, WX_PSR_VLAN_SWC_IDX, vlvf_index); 1835 if (vlan_on) { 1836 /* set the pool bit */ 1837 if (vind < 32) { 1838 bits = rd32(wx, WX_PSR_VLAN_SWC_VM_L); 1839 bits |= (1 << vind); 1840 wr32(wx, WX_PSR_VLAN_SWC_VM_L, bits); 1841 } else { 1842 bits = rd32(wx, WX_PSR_VLAN_SWC_VM_H); 1843 bits |= (1 << (vind - 32)); 1844 wr32(wx, WX_PSR_VLAN_SWC_VM_H, bits); 1845 } 1846 } else { 1847 /* clear the pool bit */ 1848 if (vind < 32) { 1849 bits = rd32(wx, WX_PSR_VLAN_SWC_VM_L); 1850 bits &= ~(1 << vind); 1851 wr32(wx, WX_PSR_VLAN_SWC_VM_L, bits); 1852 bits |= rd32(wx, WX_PSR_VLAN_SWC_VM_H); 1853 } else { 1854 bits = rd32(wx, WX_PSR_VLAN_SWC_VM_H); 1855 bits &= ~(1 << (vind - 32)); 1856 wr32(wx, WX_PSR_VLAN_SWC_VM_H, bits); 1857 bits |= rd32(wx, WX_PSR_VLAN_SWC_VM_L); 1858 } 1859 } 1860 1861 if (bits) { 1862 wr32(wx, WX_PSR_VLAN_SWC, (WX_PSR_VLAN_SWC_VIEN | vlan)); 1863 if (!vlan_on && vfta_changed) 1864 *vfta_changed = false; 1865 } else { 1866 wr32(wx, WX_PSR_VLAN_SWC, 0); 1867 } 1868 1869 return 0; 1870 } 1871 1872 /** 1873 * wx_set_vfta - Set VLAN filter table 1874 * @wx: pointer to hardware structure 1875 * @vlan: VLAN id to write to VLAN filter 1876 * @vind: VMDq output index that maps queue to VLAN id in VFVFB 1877 * @vlan_on: boolean flag to turn on/off VLAN in VFVF 1878 * 1879 * Turn on/off specified VLAN in the VLAN filter table. 1880 **/ 1881 static int wx_set_vfta(struct wx *wx, u32 vlan, u32 vind, bool vlan_on) 1882 { 1883 u32 bitindex, vfta, targetbit; 1884 bool vfta_changed = false; 1885 int regindex, ret; 1886 1887 /* this is a 2 part operation - first the VFTA, then the 1888 * VLVF and VLVFB if VT Mode is set 1889 * We don't write the VFTA until we know the VLVF part succeeded. 1890 */ 1891 1892 /* Part 1 1893 * The VFTA is a bitstring made up of 128 32-bit registers 1894 * that enable the particular VLAN id, much like the MTA: 1895 * bits[11-5]: which register 1896 * bits[4-0]: which bit in the register 1897 */ 1898 regindex = (vlan >> 5) & 0x7F; 1899 bitindex = vlan & 0x1F; 1900 targetbit = (1 << bitindex); 1901 /* errata 5 */ 1902 vfta = wx->mac.vft_shadow[regindex]; 1903 if (vlan_on) { 1904 if (!(vfta & targetbit)) { 1905 vfta |= targetbit; 1906 vfta_changed = true; 1907 } 1908 } else { 1909 if ((vfta & targetbit)) { 1910 vfta &= ~targetbit; 1911 vfta_changed = true; 1912 } 1913 } 1914 /* Part 2 1915 * Call wx_set_vlvf to set VLVFB and VLVF 1916 */ 1917 ret = wx_set_vlvf(wx, vlan, vind, vlan_on, &vfta_changed); 1918 if (ret != 0) 1919 return ret; 1920 1921 if (vfta_changed) 1922 wr32(wx, WX_PSR_VLAN_TBL(regindex), vfta); 1923 wx->mac.vft_shadow[regindex] = vfta; 1924 1925 return 0; 1926 } 1927 1928 /** 1929 * wx_clear_vfta - Clear VLAN filter table 1930 * @wx: pointer to hardware structure 1931 * 1932 * Clears the VLAN filer table, and the VMDq index associated with the filter 1933 **/ 1934 static void wx_clear_vfta(struct wx *wx) 1935 { 1936 u32 offset; 1937 1938 for (offset = 0; offset < wx->mac.vft_size; offset++) { 1939 wr32(wx, WX_PSR_VLAN_TBL(offset), 0); 1940 wx->mac.vft_shadow[offset] = 0; 1941 } 1942 1943 for (offset = 0; offset < WX_PSR_VLAN_SWC_ENTRIES; offset++) { 1944 wr32(wx, WX_PSR_VLAN_SWC_IDX, offset); 1945 wr32(wx, WX_PSR_VLAN_SWC, 0); 1946 wr32(wx, WX_PSR_VLAN_SWC_VM_L, 0); 1947 wr32(wx, WX_PSR_VLAN_SWC_VM_H, 0); 1948 } 1949 } 1950 1951 int wx_vlan_rx_add_vid(struct net_device *netdev, 1952 __be16 proto, u16 vid) 1953 { 1954 struct wx *wx = netdev_priv(netdev); 1955 1956 /* add VID to filter table */ 1957 wx_set_vfta(wx, vid, VMDQ_P(0), true); 1958 set_bit(vid, wx->active_vlans); 1959 1960 return 0; 1961 } 1962 EXPORT_SYMBOL(wx_vlan_rx_add_vid); 1963 1964 int wx_vlan_rx_kill_vid(struct net_device *netdev, __be16 proto, u16 vid) 1965 { 1966 struct wx *wx = netdev_priv(netdev); 1967 1968 /* remove VID from filter table */ 1969 if (vid) 1970 wx_set_vfta(wx, vid, VMDQ_P(0), false); 1971 clear_bit(vid, wx->active_vlans); 1972 1973 return 0; 1974 } 1975 EXPORT_SYMBOL(wx_vlan_rx_kill_vid); 1976 1977 /** 1978 * wx_start_hw - Prepare hardware for Tx/Rx 1979 * @wx: pointer to hardware structure 1980 * 1981 * Starts the hardware using the generic start_hw function 1982 * and the generation start_hw function. 1983 * Then performs revision-specific operations, if any. 1984 **/ 1985 void wx_start_hw(struct wx *wx) 1986 { 1987 int i; 1988 1989 /* Clear the VLAN filter table */ 1990 wx_clear_vfta(wx); 1991 WX_WRITE_FLUSH(wx); 1992 /* Clear the rate limiters */ 1993 for (i = 0; i < wx->mac.max_tx_queues; i++) { 1994 wr32(wx, WX_TDM_RP_IDX, i); 1995 wr32(wx, WX_TDM_RP_RATE, 0); 1996 } 1997 } 1998 EXPORT_SYMBOL(wx_start_hw); 1999 2000 MODULE_LICENSE("GPL"); 2001