1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * dwmac-sun8i.c - Allwinner sun8i DWMAC specific glue layer 4 * 5 * Copyright (C) 2017 Corentin Labbe <clabbe.montjoie@gmail.com> 6 */ 7 8 #include <linux/clk.h> 9 #include <linux/io.h> 10 #include <linux/iopoll.h> 11 #include <linux/mdio-mux.h> 12 #include <linux/mfd/syscon.h> 13 #include <linux/module.h> 14 #include <linux/of.h> 15 #include <linux/of_mdio.h> 16 #include <linux/of_net.h> 17 #include <linux/of_platform.h> 18 #include <linux/phy.h> 19 #include <linux/platform_device.h> 20 #include <linux/pm_runtime.h> 21 #include <linux/regulator/consumer.h> 22 #include <linux/regmap.h> 23 #include <linux/stmmac.h> 24 25 #include "stmmac.h" 26 #include "stmmac_platform.h" 27 28 /* General notes on dwmac-sun8i: 29 * Locking: no locking is necessary in this file because all necessary locking 30 * is done in the "stmmac files" 31 */ 32 33 /* struct emac_variant - Describe dwmac-sun8i hardware variant 34 * @default_syscon_value: The default value of the EMAC register in syscon 35 * This value is used for disabling properly EMAC 36 * and used as a good starting value in case of the 37 * boot process(uboot) leave some stuff. 38 * @syscon_field reg_field for the syscon's gmac register 39 * @soc_has_internal_phy: Does the MAC embed an internal PHY 40 * @support_mii: Does the MAC handle MII 41 * @support_rmii: Does the MAC handle RMII 42 * @support_rgmii: Does the MAC handle RGMII 43 * 44 * @rx_delay_max: Maximum raw value for RX delay chain 45 * @tx_delay_max: Maximum raw value for TX delay chain 46 * These two also indicate the bitmask for 47 * the RX and TX delay chain registers. A 48 * value of zero indicates this is not supported. 49 */ 50 struct emac_variant { 51 u32 default_syscon_value; 52 const struct reg_field *syscon_field; 53 bool soc_has_internal_phy; 54 bool support_mii; 55 bool support_rmii; 56 bool support_rgmii; 57 u8 rx_delay_max; 58 u8 tx_delay_max; 59 }; 60 61 /* struct sunxi_priv_data - hold all sunxi private data 62 * @ephy_clk: reference to the optional EPHY clock for the internal PHY 63 * @regulator: reference to the optional regulator 64 * @rst_ephy: reference to the optional EPHY reset for the internal PHY 65 * @variant: reference to the current board variant 66 * @regmap: regmap for using the syscon 67 * @internal_phy_powered: Does the internal PHY is enabled 68 * @use_internal_phy: Is the internal PHY selected for use 69 * @mux_handle: Internal pointer used by mdio-mux lib 70 */ 71 struct sunxi_priv_data { 72 struct clk *ephy_clk; 73 struct regulator *regulator; 74 struct reset_control *rst_ephy; 75 const struct emac_variant *variant; 76 struct regmap_field *regmap_field; 77 bool internal_phy_powered; 78 bool use_internal_phy; 79 void *mux_handle; 80 }; 81 82 /* EMAC clock register @ 0x30 in the "system control" address range */ 83 static const struct reg_field sun8i_syscon_reg_field = { 84 .reg = 0x30, 85 .lsb = 0, 86 .msb = 31, 87 }; 88 89 /* EMAC clock register @ 0x164 in the CCU address range */ 90 static const struct reg_field sun8i_ccu_reg_field = { 91 .reg = 0x164, 92 .lsb = 0, 93 .msb = 31, 94 }; 95 96 static const struct emac_variant emac_variant_h3 = { 97 .default_syscon_value = 0x58000, 98 .syscon_field = &sun8i_syscon_reg_field, 99 .soc_has_internal_phy = true, 100 .support_mii = true, 101 .support_rmii = true, 102 .support_rgmii = true, 103 .rx_delay_max = 31, 104 .tx_delay_max = 7, 105 }; 106 107 static const struct emac_variant emac_variant_v3s = { 108 .default_syscon_value = 0x38000, 109 .syscon_field = &sun8i_syscon_reg_field, 110 .soc_has_internal_phy = true, 111 .support_mii = true 112 }; 113 114 static const struct emac_variant emac_variant_a83t = { 115 .default_syscon_value = 0, 116 .syscon_field = &sun8i_syscon_reg_field, 117 .soc_has_internal_phy = false, 118 .support_mii = true, 119 .support_rgmii = true, 120 .rx_delay_max = 31, 121 .tx_delay_max = 7, 122 }; 123 124 static const struct emac_variant emac_variant_r40 = { 125 .default_syscon_value = 0, 126 .syscon_field = &sun8i_ccu_reg_field, 127 .support_mii = true, 128 .support_rgmii = true, 129 .rx_delay_max = 7, 130 }; 131 132 static const struct emac_variant emac_variant_a64 = { 133 .default_syscon_value = 0, 134 .syscon_field = &sun8i_syscon_reg_field, 135 .soc_has_internal_phy = false, 136 .support_mii = true, 137 .support_rmii = true, 138 .support_rgmii = true, 139 .rx_delay_max = 31, 140 .tx_delay_max = 7, 141 }; 142 143 static const struct emac_variant emac_variant_h6 = { 144 .default_syscon_value = 0x50000, 145 .syscon_field = &sun8i_syscon_reg_field, 146 /* The "Internal PHY" of H6 is not on the die. It's on the 147 * co-packaged AC200 chip instead. 148 */ 149 .soc_has_internal_phy = false, 150 .support_mii = true, 151 .support_rmii = true, 152 .support_rgmii = true, 153 .rx_delay_max = 31, 154 .tx_delay_max = 7, 155 }; 156 157 #define EMAC_BASIC_CTL0 0x00 158 #define EMAC_BASIC_CTL1 0x04 159 #define EMAC_INT_STA 0x08 160 #define EMAC_INT_EN 0x0C 161 #define EMAC_TX_CTL0 0x10 162 #define EMAC_TX_CTL1 0x14 163 #define EMAC_TX_FLOW_CTL 0x1C 164 #define EMAC_TX_DESC_LIST 0x20 165 #define EMAC_RX_CTL0 0x24 166 #define EMAC_RX_CTL1 0x28 167 #define EMAC_RX_DESC_LIST 0x34 168 #define EMAC_RX_FRM_FLT 0x38 169 #define EMAC_MDIO_CMD 0x48 170 #define EMAC_MDIO_DATA 0x4C 171 #define EMAC_MACADDR_HI(reg) (0x50 + (reg) * 8) 172 #define EMAC_MACADDR_LO(reg) (0x54 + (reg) * 8) 173 #define EMAC_TX_DMA_STA 0xB0 174 #define EMAC_TX_CUR_DESC 0xB4 175 #define EMAC_TX_CUR_BUF 0xB8 176 #define EMAC_RX_DMA_STA 0xC0 177 #define EMAC_RX_CUR_DESC 0xC4 178 #define EMAC_RX_CUR_BUF 0xC8 179 180 /* Use in EMAC_BASIC_CTL0 */ 181 #define EMAC_DUPLEX_FULL BIT(0) 182 #define EMAC_LOOPBACK BIT(1) 183 #define EMAC_SPEED_1000 0 184 #define EMAC_SPEED_100 (0x03 << 2) 185 #define EMAC_SPEED_10 (0x02 << 2) 186 187 /* Use in EMAC_BASIC_CTL1 */ 188 #define EMAC_BURSTLEN_SHIFT 24 189 190 /* Used in EMAC_RX_FRM_FLT */ 191 #define EMAC_FRM_FLT_RXALL BIT(0) 192 #define EMAC_FRM_FLT_CTL BIT(13) 193 #define EMAC_FRM_FLT_MULTICAST BIT(16) 194 195 /* Used in RX_CTL1*/ 196 #define EMAC_RX_MD BIT(1) 197 #define EMAC_RX_TH_MASK GENMASK(5, 4) 198 #define EMAC_RX_TH_32 0 199 #define EMAC_RX_TH_64 (0x1 << 4) 200 #define EMAC_RX_TH_96 (0x2 << 4) 201 #define EMAC_RX_TH_128 (0x3 << 4) 202 #define EMAC_RX_DMA_EN BIT(30) 203 #define EMAC_RX_DMA_START BIT(31) 204 205 /* Used in TX_CTL1*/ 206 #define EMAC_TX_MD BIT(1) 207 #define EMAC_TX_NEXT_FRM BIT(2) 208 #define EMAC_TX_TH_MASK GENMASK(10, 8) 209 #define EMAC_TX_TH_64 0 210 #define EMAC_TX_TH_128 (0x1 << 8) 211 #define EMAC_TX_TH_192 (0x2 << 8) 212 #define EMAC_TX_TH_256 (0x3 << 8) 213 #define EMAC_TX_DMA_EN BIT(30) 214 #define EMAC_TX_DMA_START BIT(31) 215 216 /* Used in RX_CTL0 */ 217 #define EMAC_RX_RECEIVER_EN BIT(31) 218 #define EMAC_RX_DO_CRC BIT(27) 219 #define EMAC_RX_FLOW_CTL_EN BIT(16) 220 221 /* Used in TX_CTL0 */ 222 #define EMAC_TX_TRANSMITTER_EN BIT(31) 223 224 /* Used in EMAC_TX_FLOW_CTL */ 225 #define EMAC_TX_FLOW_CTL_EN BIT(0) 226 227 /* Used in EMAC_INT_STA */ 228 #define EMAC_TX_INT BIT(0) 229 #define EMAC_TX_DMA_STOP_INT BIT(1) 230 #define EMAC_TX_BUF_UA_INT BIT(2) 231 #define EMAC_TX_TIMEOUT_INT BIT(3) 232 #define EMAC_TX_UNDERFLOW_INT BIT(4) 233 #define EMAC_TX_EARLY_INT BIT(5) 234 #define EMAC_RX_INT BIT(8) 235 #define EMAC_RX_BUF_UA_INT BIT(9) 236 #define EMAC_RX_DMA_STOP_INT BIT(10) 237 #define EMAC_RX_TIMEOUT_INT BIT(11) 238 #define EMAC_RX_OVERFLOW_INT BIT(12) 239 #define EMAC_RX_EARLY_INT BIT(13) 240 #define EMAC_RGMII_STA_INT BIT(16) 241 242 #define EMAC_INT_MSK_COMMON EMAC_RGMII_STA_INT 243 #define EMAC_INT_MSK_TX (EMAC_TX_INT | \ 244 EMAC_TX_DMA_STOP_INT | \ 245 EMAC_TX_BUF_UA_INT | \ 246 EMAC_TX_TIMEOUT_INT | \ 247 EMAC_TX_UNDERFLOW_INT | \ 248 EMAC_TX_EARLY_INT |\ 249 EMAC_INT_MSK_COMMON) 250 #define EMAC_INT_MSK_RX (EMAC_RX_INT | \ 251 EMAC_RX_BUF_UA_INT | \ 252 EMAC_RX_DMA_STOP_INT | \ 253 EMAC_RX_TIMEOUT_INT | \ 254 EMAC_RX_OVERFLOW_INT | \ 255 EMAC_RX_EARLY_INT | \ 256 EMAC_INT_MSK_COMMON) 257 258 #define MAC_ADDR_TYPE_DST BIT(31) 259 260 /* H3 specific bits for EPHY */ 261 #define H3_EPHY_ADDR_SHIFT 20 262 #define H3_EPHY_CLK_SEL BIT(18) /* 1: 24MHz, 0: 25MHz */ 263 #define H3_EPHY_LED_POL BIT(17) /* 1: active low, 0: active high */ 264 #define H3_EPHY_SHUTDOWN BIT(16) /* 1: shutdown, 0: power up */ 265 #define H3_EPHY_SELECT BIT(15) /* 1: internal PHY, 0: external PHY */ 266 #define H3_EPHY_MUX_MASK (H3_EPHY_SHUTDOWN | H3_EPHY_SELECT) 267 #define DWMAC_SUN8I_MDIO_MUX_INTERNAL_ID 1 268 #define DWMAC_SUN8I_MDIO_MUX_EXTERNAL_ID 2 269 270 /* H3/A64 specific bits */ 271 #define SYSCON_RMII_EN BIT(13) /* 1: enable RMII (overrides EPIT) */ 272 273 /* Generic system control EMAC_CLK bits */ 274 #define SYSCON_ETXDC_SHIFT 10 275 #define SYSCON_ERXDC_SHIFT 5 276 /* EMAC PHY Interface Type */ 277 #define SYSCON_EPIT BIT(2) /* 1: RGMII, 0: MII */ 278 #define SYSCON_ETCS_MASK GENMASK(1, 0) 279 #define SYSCON_ETCS_MII 0x0 280 #define SYSCON_ETCS_EXT_GMII 0x1 281 #define SYSCON_ETCS_INT_GMII 0x2 282 283 /* sun8i_dwmac_dma_reset() - reset the EMAC 284 * Called from stmmac via stmmac_dma_ops->reset 285 */ 286 static int sun8i_dwmac_dma_reset(void __iomem *ioaddr) 287 { 288 writel(0, ioaddr + EMAC_RX_CTL1); 289 writel(0, ioaddr + EMAC_TX_CTL1); 290 writel(0, ioaddr + EMAC_RX_FRM_FLT); 291 writel(0, ioaddr + EMAC_RX_DESC_LIST); 292 writel(0, ioaddr + EMAC_TX_DESC_LIST); 293 writel(0, ioaddr + EMAC_INT_EN); 294 writel(0x1FFFFFF, ioaddr + EMAC_INT_STA); 295 return 0; 296 } 297 298 /* sun8i_dwmac_dma_init() - initialize the EMAC 299 * Called from stmmac via stmmac_dma_ops->init 300 */ 301 static void sun8i_dwmac_dma_init(void __iomem *ioaddr, 302 struct stmmac_dma_cfg *dma_cfg, int atds) 303 { 304 writel(EMAC_RX_INT | EMAC_TX_INT, ioaddr + EMAC_INT_EN); 305 writel(0x1FFFFFF, ioaddr + EMAC_INT_STA); 306 } 307 308 static void sun8i_dwmac_dma_init_rx(struct stmmac_priv *priv, 309 void __iomem *ioaddr, 310 struct stmmac_dma_cfg *dma_cfg, 311 dma_addr_t dma_rx_phy, u32 chan) 312 { 313 /* Write RX descriptors address */ 314 writel(lower_32_bits(dma_rx_phy), ioaddr + EMAC_RX_DESC_LIST); 315 } 316 317 static void sun8i_dwmac_dma_init_tx(struct stmmac_priv *priv, 318 void __iomem *ioaddr, 319 struct stmmac_dma_cfg *dma_cfg, 320 dma_addr_t dma_tx_phy, u32 chan) 321 { 322 /* Write TX descriptors address */ 323 writel(lower_32_bits(dma_tx_phy), ioaddr + EMAC_TX_DESC_LIST); 324 } 325 326 /* sun8i_dwmac_dump_regs() - Dump EMAC address space 327 * Called from stmmac_dma_ops->dump_regs 328 * Used for ethtool 329 */ 330 static void sun8i_dwmac_dump_regs(struct stmmac_priv *priv, 331 void __iomem *ioaddr, u32 *reg_space) 332 { 333 int i; 334 335 for (i = 0; i < 0xC8; i += 4) { 336 if (i == 0x32 || i == 0x3C) 337 continue; 338 reg_space[i / 4] = readl(ioaddr + i); 339 } 340 } 341 342 /* sun8i_dwmac_dump_mac_regs() - Dump EMAC address space 343 * Called from stmmac_ops->dump_regs 344 * Used for ethtool 345 */ 346 static void sun8i_dwmac_dump_mac_regs(struct mac_device_info *hw, 347 u32 *reg_space) 348 { 349 int i; 350 void __iomem *ioaddr = hw->pcsr; 351 352 for (i = 0; i < 0xC8; i += 4) { 353 if (i == 0x32 || i == 0x3C) 354 continue; 355 reg_space[i / 4] = readl(ioaddr + i); 356 } 357 } 358 359 static void sun8i_dwmac_enable_dma_irq(struct stmmac_priv *priv, 360 void __iomem *ioaddr, u32 chan, 361 bool rx, bool tx) 362 { 363 u32 value = readl(ioaddr + EMAC_INT_EN); 364 365 if (rx) 366 value |= EMAC_RX_INT; 367 if (tx) 368 value |= EMAC_TX_INT; 369 370 writel(value, ioaddr + EMAC_INT_EN); 371 } 372 373 static void sun8i_dwmac_disable_dma_irq(struct stmmac_priv *priv, 374 void __iomem *ioaddr, u32 chan, 375 bool rx, bool tx) 376 { 377 u32 value = readl(ioaddr + EMAC_INT_EN); 378 379 if (rx) 380 value &= ~EMAC_RX_INT; 381 if (tx) 382 value &= ~EMAC_TX_INT; 383 384 writel(value, ioaddr + EMAC_INT_EN); 385 } 386 387 static void sun8i_dwmac_dma_start_tx(struct stmmac_priv *priv, 388 void __iomem *ioaddr, u32 chan) 389 { 390 u32 v; 391 392 v = readl(ioaddr + EMAC_TX_CTL1); 393 v |= EMAC_TX_DMA_START; 394 v |= EMAC_TX_DMA_EN; 395 writel(v, ioaddr + EMAC_TX_CTL1); 396 } 397 398 static void sun8i_dwmac_enable_dma_transmission(void __iomem *ioaddr) 399 { 400 u32 v; 401 402 v = readl(ioaddr + EMAC_TX_CTL1); 403 v |= EMAC_TX_DMA_START; 404 v |= EMAC_TX_DMA_EN; 405 writel(v, ioaddr + EMAC_TX_CTL1); 406 } 407 408 static void sun8i_dwmac_dma_stop_tx(struct stmmac_priv *priv, 409 void __iomem *ioaddr, u32 chan) 410 { 411 u32 v; 412 413 v = readl(ioaddr + EMAC_TX_CTL1); 414 v &= ~EMAC_TX_DMA_EN; 415 writel(v, ioaddr + EMAC_TX_CTL1); 416 } 417 418 static void sun8i_dwmac_dma_start_rx(struct stmmac_priv *priv, 419 void __iomem *ioaddr, u32 chan) 420 { 421 u32 v; 422 423 v = readl(ioaddr + EMAC_RX_CTL1); 424 v |= EMAC_RX_DMA_START; 425 v |= EMAC_RX_DMA_EN; 426 writel(v, ioaddr + EMAC_RX_CTL1); 427 } 428 429 static void sun8i_dwmac_dma_stop_rx(struct stmmac_priv *priv, 430 void __iomem *ioaddr, u32 chan) 431 { 432 u32 v; 433 434 v = readl(ioaddr + EMAC_RX_CTL1); 435 v &= ~EMAC_RX_DMA_EN; 436 writel(v, ioaddr + EMAC_RX_CTL1); 437 } 438 439 static int sun8i_dwmac_dma_interrupt(struct stmmac_priv *priv, 440 void __iomem *ioaddr, 441 struct stmmac_extra_stats *x, u32 chan, 442 u32 dir) 443 { 444 struct stmmac_pcpu_stats *stats = this_cpu_ptr(priv->xstats.pcpu_stats); 445 int ret = 0; 446 u32 v; 447 448 v = readl(ioaddr + EMAC_INT_STA); 449 450 if (dir == DMA_DIR_RX) 451 v &= EMAC_INT_MSK_RX; 452 else if (dir == DMA_DIR_TX) 453 v &= EMAC_INT_MSK_TX; 454 455 if (v & EMAC_TX_INT) { 456 ret |= handle_tx; 457 u64_stats_update_begin(&stats->syncp); 458 u64_stats_inc(&stats->tx_normal_irq_n[chan]); 459 u64_stats_update_end(&stats->syncp); 460 } 461 462 if (v & EMAC_TX_DMA_STOP_INT) 463 x->tx_process_stopped_irq++; 464 465 if (v & EMAC_TX_BUF_UA_INT) 466 x->tx_process_stopped_irq++; 467 468 if (v & EMAC_TX_TIMEOUT_INT) 469 ret |= tx_hard_error; 470 471 if (v & EMAC_TX_UNDERFLOW_INT) { 472 ret |= tx_hard_error; 473 x->tx_undeflow_irq++; 474 } 475 476 if (v & EMAC_TX_EARLY_INT) 477 x->tx_early_irq++; 478 479 if (v & EMAC_RX_INT) { 480 ret |= handle_rx; 481 u64_stats_update_begin(&stats->syncp); 482 u64_stats_inc(&stats->rx_normal_irq_n[chan]); 483 u64_stats_update_end(&stats->syncp); 484 } 485 486 if (v & EMAC_RX_BUF_UA_INT) 487 x->rx_buf_unav_irq++; 488 489 if (v & EMAC_RX_DMA_STOP_INT) 490 x->rx_process_stopped_irq++; 491 492 if (v & EMAC_RX_TIMEOUT_INT) 493 ret |= tx_hard_error; 494 495 if (v & EMAC_RX_OVERFLOW_INT) { 496 ret |= tx_hard_error; 497 x->rx_overflow_irq++; 498 } 499 500 if (v & EMAC_RX_EARLY_INT) 501 x->rx_early_irq++; 502 503 if (v & EMAC_RGMII_STA_INT) 504 x->irq_rgmii_n++; 505 506 writel(v, ioaddr + EMAC_INT_STA); 507 508 return ret; 509 } 510 511 static void sun8i_dwmac_dma_operation_mode_rx(struct stmmac_priv *priv, 512 void __iomem *ioaddr, int mode, 513 u32 channel, int fifosz, u8 qmode) 514 { 515 u32 v; 516 517 v = readl(ioaddr + EMAC_RX_CTL1); 518 if (mode == SF_DMA_MODE) { 519 v |= EMAC_RX_MD; 520 } else { 521 v &= ~EMAC_RX_MD; 522 v &= ~EMAC_RX_TH_MASK; 523 if (mode < 32) 524 v |= EMAC_RX_TH_32; 525 else if (mode < 64) 526 v |= EMAC_RX_TH_64; 527 else if (mode < 96) 528 v |= EMAC_RX_TH_96; 529 else if (mode < 128) 530 v |= EMAC_RX_TH_128; 531 } 532 writel(v, ioaddr + EMAC_RX_CTL1); 533 } 534 535 static void sun8i_dwmac_dma_operation_mode_tx(struct stmmac_priv *priv, 536 void __iomem *ioaddr, int mode, 537 u32 channel, int fifosz, u8 qmode) 538 { 539 u32 v; 540 541 v = readl(ioaddr + EMAC_TX_CTL1); 542 if (mode == SF_DMA_MODE) { 543 v |= EMAC_TX_MD; 544 /* Undocumented bit (called TX_NEXT_FRM in BSP), the original 545 * comment is 546 * "Operating on second frame increase the performance 547 * especially when transmit store-and-forward is used." 548 */ 549 v |= EMAC_TX_NEXT_FRM; 550 } else { 551 v &= ~EMAC_TX_MD; 552 v &= ~EMAC_TX_TH_MASK; 553 if (mode < 64) 554 v |= EMAC_TX_TH_64; 555 else if (mode < 128) 556 v |= EMAC_TX_TH_128; 557 else if (mode < 192) 558 v |= EMAC_TX_TH_192; 559 else if (mode < 256) 560 v |= EMAC_TX_TH_256; 561 } 562 writel(v, ioaddr + EMAC_TX_CTL1); 563 } 564 565 static const struct stmmac_dma_ops sun8i_dwmac_dma_ops = { 566 .reset = sun8i_dwmac_dma_reset, 567 .init = sun8i_dwmac_dma_init, 568 .init_rx_chan = sun8i_dwmac_dma_init_rx, 569 .init_tx_chan = sun8i_dwmac_dma_init_tx, 570 .dump_regs = sun8i_dwmac_dump_regs, 571 .dma_rx_mode = sun8i_dwmac_dma_operation_mode_rx, 572 .dma_tx_mode = sun8i_dwmac_dma_operation_mode_tx, 573 .enable_dma_transmission = sun8i_dwmac_enable_dma_transmission, 574 .enable_dma_irq = sun8i_dwmac_enable_dma_irq, 575 .disable_dma_irq = sun8i_dwmac_disable_dma_irq, 576 .start_tx = sun8i_dwmac_dma_start_tx, 577 .stop_tx = sun8i_dwmac_dma_stop_tx, 578 .start_rx = sun8i_dwmac_dma_start_rx, 579 .stop_rx = sun8i_dwmac_dma_stop_rx, 580 .dma_interrupt = sun8i_dwmac_dma_interrupt, 581 }; 582 583 static int sun8i_dwmac_power_internal_phy(struct stmmac_priv *priv); 584 585 static int sun8i_dwmac_init(struct platform_device *pdev, void *priv) 586 { 587 struct net_device *ndev = platform_get_drvdata(pdev); 588 struct sunxi_priv_data *gmac = priv; 589 int ret; 590 591 if (gmac->regulator) { 592 ret = regulator_enable(gmac->regulator); 593 if (ret) { 594 dev_err(&pdev->dev, "Fail to enable regulator\n"); 595 return ret; 596 } 597 } 598 599 if (gmac->use_internal_phy) { 600 ret = sun8i_dwmac_power_internal_phy(netdev_priv(ndev)); 601 if (ret) 602 goto err_disable_regulator; 603 } 604 605 return 0; 606 607 err_disable_regulator: 608 if (gmac->regulator) 609 regulator_disable(gmac->regulator); 610 611 return ret; 612 } 613 614 static void sun8i_dwmac_core_init(struct mac_device_info *hw, 615 struct net_device *dev) 616 { 617 void __iomem *ioaddr = hw->pcsr; 618 u32 v; 619 620 v = (8 << EMAC_BURSTLEN_SHIFT); /* burst len */ 621 writel(v, ioaddr + EMAC_BASIC_CTL1); 622 } 623 624 static void sun8i_dwmac_set_mac(void __iomem *ioaddr, bool enable) 625 { 626 u32 t, r; 627 628 t = readl(ioaddr + EMAC_TX_CTL0); 629 r = readl(ioaddr + EMAC_RX_CTL0); 630 if (enable) { 631 t |= EMAC_TX_TRANSMITTER_EN; 632 r |= EMAC_RX_RECEIVER_EN; 633 } else { 634 t &= ~EMAC_TX_TRANSMITTER_EN; 635 r &= ~EMAC_RX_RECEIVER_EN; 636 } 637 writel(t, ioaddr + EMAC_TX_CTL0); 638 writel(r, ioaddr + EMAC_RX_CTL0); 639 } 640 641 /* Set MAC address at slot reg_n 642 * All slot > 0 need to be enabled with MAC_ADDR_TYPE_DST 643 * If addr is NULL, clear the slot 644 */ 645 static void sun8i_dwmac_set_umac_addr(struct mac_device_info *hw, 646 const unsigned char *addr, 647 unsigned int reg_n) 648 { 649 void __iomem *ioaddr = hw->pcsr; 650 u32 v; 651 652 if (!addr) { 653 writel(0, ioaddr + EMAC_MACADDR_HI(reg_n)); 654 return; 655 } 656 657 stmmac_set_mac_addr(ioaddr, addr, EMAC_MACADDR_HI(reg_n), 658 EMAC_MACADDR_LO(reg_n)); 659 if (reg_n > 0) { 660 v = readl(ioaddr + EMAC_MACADDR_HI(reg_n)); 661 v |= MAC_ADDR_TYPE_DST; 662 writel(v, ioaddr + EMAC_MACADDR_HI(reg_n)); 663 } 664 } 665 666 static void sun8i_dwmac_get_umac_addr(struct mac_device_info *hw, 667 unsigned char *addr, 668 unsigned int reg_n) 669 { 670 void __iomem *ioaddr = hw->pcsr; 671 672 stmmac_get_mac_addr(ioaddr, addr, EMAC_MACADDR_HI(reg_n), 673 EMAC_MACADDR_LO(reg_n)); 674 } 675 676 /* caution this function must return non 0 to work */ 677 static int sun8i_dwmac_rx_ipc_enable(struct mac_device_info *hw) 678 { 679 void __iomem *ioaddr = hw->pcsr; 680 u32 v; 681 682 v = readl(ioaddr + EMAC_RX_CTL0); 683 v |= EMAC_RX_DO_CRC; 684 writel(v, ioaddr + EMAC_RX_CTL0); 685 686 return 1; 687 } 688 689 static void sun8i_dwmac_set_filter(struct mac_device_info *hw, 690 struct net_device *dev) 691 { 692 void __iomem *ioaddr = hw->pcsr; 693 u32 v; 694 int i = 1; 695 struct netdev_hw_addr *ha; 696 int macaddrs = netdev_uc_count(dev) + netdev_mc_count(dev) + 1; 697 698 v = EMAC_FRM_FLT_CTL; 699 700 if (dev->flags & IFF_PROMISC) { 701 v = EMAC_FRM_FLT_RXALL; 702 } else if (dev->flags & IFF_ALLMULTI) { 703 v |= EMAC_FRM_FLT_MULTICAST; 704 } else if (macaddrs <= hw->unicast_filter_entries) { 705 if (!netdev_mc_empty(dev)) { 706 netdev_for_each_mc_addr(ha, dev) { 707 sun8i_dwmac_set_umac_addr(hw, ha->addr, i); 708 i++; 709 } 710 } 711 if (!netdev_uc_empty(dev)) { 712 netdev_for_each_uc_addr(ha, dev) { 713 sun8i_dwmac_set_umac_addr(hw, ha->addr, i); 714 i++; 715 } 716 } 717 } else { 718 if (!(readl(ioaddr + EMAC_RX_FRM_FLT) & EMAC_FRM_FLT_RXALL)) 719 netdev_info(dev, "Too many address, switching to promiscuous\n"); 720 v = EMAC_FRM_FLT_RXALL; 721 } 722 723 /* Disable unused address filter slots */ 724 while (i < hw->unicast_filter_entries) 725 sun8i_dwmac_set_umac_addr(hw, NULL, i++); 726 727 writel(v, ioaddr + EMAC_RX_FRM_FLT); 728 } 729 730 static void sun8i_dwmac_flow_ctrl(struct mac_device_info *hw, 731 unsigned int duplex, unsigned int fc, 732 unsigned int pause_time, u32 tx_cnt) 733 { 734 void __iomem *ioaddr = hw->pcsr; 735 u32 v; 736 737 v = readl(ioaddr + EMAC_RX_CTL0); 738 if (fc == FLOW_AUTO) 739 v |= EMAC_RX_FLOW_CTL_EN; 740 else 741 v &= ~EMAC_RX_FLOW_CTL_EN; 742 writel(v, ioaddr + EMAC_RX_CTL0); 743 744 v = readl(ioaddr + EMAC_TX_FLOW_CTL); 745 if (fc == FLOW_AUTO) 746 v |= EMAC_TX_FLOW_CTL_EN; 747 else 748 v &= ~EMAC_TX_FLOW_CTL_EN; 749 writel(v, ioaddr + EMAC_TX_FLOW_CTL); 750 } 751 752 static int sun8i_dwmac_reset(struct stmmac_priv *priv) 753 { 754 u32 v; 755 int err; 756 757 v = readl(priv->ioaddr + EMAC_BASIC_CTL1); 758 writel(v | 0x01, priv->ioaddr + EMAC_BASIC_CTL1); 759 760 /* The timeout was previoulsy set to 10ms, but some board (OrangePI0) 761 * need more if no cable plugged. 100ms seems OK 762 */ 763 err = readl_poll_timeout(priv->ioaddr + EMAC_BASIC_CTL1, v, 764 !(v & 0x01), 100, 100000); 765 766 if (err) { 767 dev_err(priv->device, "EMAC reset timeout\n"); 768 return err; 769 } 770 return 0; 771 } 772 773 /* Search in mdio-mux node for internal PHY node and get its clk/reset */ 774 static int get_ephy_nodes(struct stmmac_priv *priv) 775 { 776 struct sunxi_priv_data *gmac = priv->plat->bsp_priv; 777 struct device_node *mdio_mux, *iphynode; 778 struct device_node *mdio_internal; 779 int ret; 780 781 mdio_mux = of_get_child_by_name(priv->device->of_node, "mdio-mux"); 782 if (!mdio_mux) { 783 dev_err(priv->device, "Cannot get mdio-mux node\n"); 784 return -ENODEV; 785 } 786 787 mdio_internal = of_get_compatible_child(mdio_mux, 788 "allwinner,sun8i-h3-mdio-internal"); 789 of_node_put(mdio_mux); 790 if (!mdio_internal) { 791 dev_err(priv->device, "Cannot get internal_mdio node\n"); 792 return -ENODEV; 793 } 794 795 /* Seek for internal PHY */ 796 for_each_child_of_node(mdio_internal, iphynode) { 797 gmac->ephy_clk = of_clk_get(iphynode, 0); 798 if (IS_ERR(gmac->ephy_clk)) 799 continue; 800 gmac->rst_ephy = of_reset_control_get_exclusive(iphynode, NULL); 801 if (IS_ERR(gmac->rst_ephy)) { 802 ret = PTR_ERR(gmac->rst_ephy); 803 if (ret == -EPROBE_DEFER) { 804 of_node_put(iphynode); 805 of_node_put(mdio_internal); 806 return ret; 807 } 808 continue; 809 } 810 dev_info(priv->device, "Found internal PHY node\n"); 811 of_node_put(iphynode); 812 of_node_put(mdio_internal); 813 return 0; 814 } 815 816 of_node_put(mdio_internal); 817 return -ENODEV; 818 } 819 820 static int sun8i_dwmac_power_internal_phy(struct stmmac_priv *priv) 821 { 822 struct sunxi_priv_data *gmac = priv->plat->bsp_priv; 823 int ret; 824 825 if (gmac->internal_phy_powered) { 826 dev_warn(priv->device, "Internal PHY already powered\n"); 827 return 0; 828 } 829 830 dev_info(priv->device, "Powering internal PHY\n"); 831 ret = clk_prepare_enable(gmac->ephy_clk); 832 if (ret) { 833 dev_err(priv->device, "Cannot enable internal PHY\n"); 834 return ret; 835 } 836 837 /* Make sure the EPHY is properly reseted, as U-Boot may leave 838 * it at deasserted state, and thus it may fail to reset EMAC. 839 * 840 * This assumes the driver has exclusive access to the EPHY reset. 841 */ 842 ret = reset_control_reset(gmac->rst_ephy); 843 if (ret) { 844 dev_err(priv->device, "Cannot reset internal PHY\n"); 845 clk_disable_unprepare(gmac->ephy_clk); 846 return ret; 847 } 848 849 gmac->internal_phy_powered = true; 850 851 return 0; 852 } 853 854 static void sun8i_dwmac_unpower_internal_phy(struct sunxi_priv_data *gmac) 855 { 856 if (!gmac->internal_phy_powered) 857 return; 858 859 clk_disable_unprepare(gmac->ephy_clk); 860 reset_control_assert(gmac->rst_ephy); 861 gmac->internal_phy_powered = false; 862 } 863 864 /* MDIO multiplexing switch function 865 * This function is called by the mdio-mux layer when it thinks the mdio bus 866 * multiplexer needs to switch. 867 * 'current_child' is the current value of the mux register 868 * 'desired_child' is the value of the 'reg' property of the target child MDIO 869 * node. 870 * The first time this function is called, current_child == -1. 871 * If current_child == desired_child, then the mux is already set to the 872 * correct bus. 873 */ 874 static int mdio_mux_syscon_switch_fn(int current_child, int desired_child, 875 void *data) 876 { 877 struct stmmac_priv *priv = data; 878 struct sunxi_priv_data *gmac = priv->plat->bsp_priv; 879 u32 reg, val; 880 int ret = 0; 881 882 if (current_child ^ desired_child) { 883 regmap_field_read(gmac->regmap_field, ®); 884 switch (desired_child) { 885 case DWMAC_SUN8I_MDIO_MUX_INTERNAL_ID: 886 dev_info(priv->device, "Switch mux to internal PHY"); 887 val = (reg & ~H3_EPHY_MUX_MASK) | H3_EPHY_SELECT; 888 gmac->use_internal_phy = true; 889 break; 890 case DWMAC_SUN8I_MDIO_MUX_EXTERNAL_ID: 891 dev_info(priv->device, "Switch mux to external PHY"); 892 val = (reg & ~H3_EPHY_MUX_MASK) | H3_EPHY_SHUTDOWN; 893 gmac->use_internal_phy = false; 894 break; 895 default: 896 dev_err(priv->device, "Invalid child ID %x\n", 897 desired_child); 898 return -EINVAL; 899 } 900 regmap_field_write(gmac->regmap_field, val); 901 if (gmac->use_internal_phy) { 902 ret = sun8i_dwmac_power_internal_phy(priv); 903 if (ret) 904 return ret; 905 } else { 906 sun8i_dwmac_unpower_internal_phy(gmac); 907 } 908 /* After changing syscon value, the MAC need reset or it will 909 * use the last value (and so the last PHY set). 910 */ 911 ret = sun8i_dwmac_reset(priv); 912 } 913 return ret; 914 } 915 916 static int sun8i_dwmac_register_mdio_mux(struct stmmac_priv *priv) 917 { 918 int ret; 919 struct device_node *mdio_mux; 920 struct sunxi_priv_data *gmac = priv->plat->bsp_priv; 921 922 mdio_mux = of_get_child_by_name(priv->device->of_node, "mdio-mux"); 923 if (!mdio_mux) 924 return -ENODEV; 925 926 ret = mdio_mux_init(priv->device, mdio_mux, mdio_mux_syscon_switch_fn, 927 &gmac->mux_handle, priv, priv->mii); 928 of_node_put(mdio_mux); 929 return ret; 930 } 931 932 static int sun8i_dwmac_set_syscon(struct device *dev, 933 struct plat_stmmacenet_data *plat) 934 { 935 struct sunxi_priv_data *gmac = plat->bsp_priv; 936 struct device_node *node = dev->of_node; 937 int ret; 938 u32 reg, val; 939 940 ret = regmap_field_read(gmac->regmap_field, &val); 941 if (ret) { 942 dev_err(dev, "Fail to read from regmap field.\n"); 943 return ret; 944 } 945 946 reg = gmac->variant->default_syscon_value; 947 if (reg != val) 948 dev_warn(dev, 949 "Current syscon value is not the default %x (expect %x)\n", 950 val, reg); 951 952 if (gmac->variant->soc_has_internal_phy) { 953 if (of_property_read_bool(node, "allwinner,leds-active-low")) 954 reg |= H3_EPHY_LED_POL; 955 else 956 reg &= ~H3_EPHY_LED_POL; 957 958 /* Force EPHY xtal frequency to 24MHz. */ 959 reg |= H3_EPHY_CLK_SEL; 960 961 ret = of_mdio_parse_addr(dev, plat->phy_node); 962 if (ret < 0) { 963 dev_err(dev, "Could not parse MDIO addr\n"); 964 return ret; 965 } 966 /* of_mdio_parse_addr returns a valid (0 ~ 31) PHY 967 * address. No need to mask it again. 968 */ 969 reg |= 1 << H3_EPHY_ADDR_SHIFT; 970 } else { 971 /* For SoCs without internal PHY the PHY selection bit should be 972 * set to 0 (external PHY). 973 */ 974 reg &= ~H3_EPHY_SELECT; 975 } 976 977 if (!of_property_read_u32(node, "allwinner,tx-delay-ps", &val)) { 978 if (val % 100) { 979 dev_err(dev, "tx-delay must be a multiple of 100\n"); 980 return -EINVAL; 981 } 982 val /= 100; 983 dev_dbg(dev, "set tx-delay to %x\n", val); 984 if (val <= gmac->variant->tx_delay_max) { 985 reg &= ~(gmac->variant->tx_delay_max << 986 SYSCON_ETXDC_SHIFT); 987 reg |= (val << SYSCON_ETXDC_SHIFT); 988 } else { 989 dev_err(dev, "Invalid TX clock delay: %d\n", 990 val); 991 return -EINVAL; 992 } 993 } 994 995 if (!of_property_read_u32(node, "allwinner,rx-delay-ps", &val)) { 996 if (val % 100) { 997 dev_err(dev, "rx-delay must be a multiple of 100\n"); 998 return -EINVAL; 999 } 1000 val /= 100; 1001 dev_dbg(dev, "set rx-delay to %x\n", val); 1002 if (val <= gmac->variant->rx_delay_max) { 1003 reg &= ~(gmac->variant->rx_delay_max << 1004 SYSCON_ERXDC_SHIFT); 1005 reg |= (val << SYSCON_ERXDC_SHIFT); 1006 } else { 1007 dev_err(dev, "Invalid RX clock delay: %d\n", 1008 val); 1009 return -EINVAL; 1010 } 1011 } 1012 1013 /* Clear interface mode bits */ 1014 reg &= ~(SYSCON_ETCS_MASK | SYSCON_EPIT); 1015 if (gmac->variant->support_rmii) 1016 reg &= ~SYSCON_RMII_EN; 1017 1018 switch (plat->mac_interface) { 1019 case PHY_INTERFACE_MODE_MII: 1020 /* default */ 1021 break; 1022 case PHY_INTERFACE_MODE_RGMII: 1023 case PHY_INTERFACE_MODE_RGMII_ID: 1024 case PHY_INTERFACE_MODE_RGMII_RXID: 1025 case PHY_INTERFACE_MODE_RGMII_TXID: 1026 reg |= SYSCON_EPIT | SYSCON_ETCS_INT_GMII; 1027 break; 1028 case PHY_INTERFACE_MODE_RMII: 1029 reg |= SYSCON_RMII_EN | SYSCON_ETCS_EXT_GMII; 1030 break; 1031 default: 1032 dev_err(dev, "Unsupported interface mode: %s", 1033 phy_modes(plat->mac_interface)); 1034 return -EINVAL; 1035 } 1036 1037 regmap_field_write(gmac->regmap_field, reg); 1038 1039 return 0; 1040 } 1041 1042 static void sun8i_dwmac_unset_syscon(struct sunxi_priv_data *gmac) 1043 { 1044 u32 reg = gmac->variant->default_syscon_value; 1045 1046 regmap_field_write(gmac->regmap_field, reg); 1047 } 1048 1049 static void sun8i_dwmac_exit(struct platform_device *pdev, void *priv) 1050 { 1051 struct sunxi_priv_data *gmac = priv; 1052 1053 if (gmac->variant->soc_has_internal_phy) 1054 sun8i_dwmac_unpower_internal_phy(gmac); 1055 1056 if (gmac->regulator) 1057 regulator_disable(gmac->regulator); 1058 } 1059 1060 static void sun8i_dwmac_set_mac_loopback(void __iomem *ioaddr, bool enable) 1061 { 1062 u32 value = readl(ioaddr + EMAC_BASIC_CTL0); 1063 1064 if (enable) 1065 value |= EMAC_LOOPBACK; 1066 else 1067 value &= ~EMAC_LOOPBACK; 1068 1069 writel(value, ioaddr + EMAC_BASIC_CTL0); 1070 } 1071 1072 static const struct stmmac_ops sun8i_dwmac_ops = { 1073 .core_init = sun8i_dwmac_core_init, 1074 .set_mac = sun8i_dwmac_set_mac, 1075 .dump_regs = sun8i_dwmac_dump_mac_regs, 1076 .rx_ipc = sun8i_dwmac_rx_ipc_enable, 1077 .set_filter = sun8i_dwmac_set_filter, 1078 .flow_ctrl = sun8i_dwmac_flow_ctrl, 1079 .set_umac_addr = sun8i_dwmac_set_umac_addr, 1080 .get_umac_addr = sun8i_dwmac_get_umac_addr, 1081 .set_mac_loopback = sun8i_dwmac_set_mac_loopback, 1082 }; 1083 1084 static struct mac_device_info *sun8i_dwmac_setup(void *ppriv) 1085 { 1086 struct mac_device_info *mac; 1087 struct stmmac_priv *priv = ppriv; 1088 1089 mac = devm_kzalloc(priv->device, sizeof(*mac), GFP_KERNEL); 1090 if (!mac) 1091 return NULL; 1092 1093 mac->pcsr = priv->ioaddr; 1094 mac->mac = &sun8i_dwmac_ops; 1095 mac->dma = &sun8i_dwmac_dma_ops; 1096 1097 priv->dev->priv_flags |= IFF_UNICAST_FLT; 1098 1099 mac->link.caps = MAC_ASYM_PAUSE | MAC_SYM_PAUSE | 1100 MAC_10 | MAC_100 | MAC_1000; 1101 /* The loopback bit seems to be re-set when link change 1102 * Simply mask it each time 1103 * Speed 10/100/1000 are set in BIT(2)/BIT(3) 1104 */ 1105 mac->link.speed_mask = GENMASK(3, 2) | EMAC_LOOPBACK; 1106 mac->link.speed10 = EMAC_SPEED_10; 1107 mac->link.speed100 = EMAC_SPEED_100; 1108 mac->link.speed1000 = EMAC_SPEED_1000; 1109 mac->link.duplex = EMAC_DUPLEX_FULL; 1110 mac->mii.addr = EMAC_MDIO_CMD; 1111 mac->mii.data = EMAC_MDIO_DATA; 1112 mac->mii.reg_shift = 4; 1113 mac->mii.reg_mask = GENMASK(8, 4); 1114 mac->mii.addr_shift = 12; 1115 mac->mii.addr_mask = GENMASK(16, 12); 1116 mac->mii.clk_csr_shift = 20; 1117 mac->mii.clk_csr_mask = GENMASK(22, 20); 1118 mac->unicast_filter_entries = 8; 1119 1120 /* Synopsys Id is not available */ 1121 priv->synopsys_id = 0; 1122 1123 return mac; 1124 } 1125 1126 static struct regmap *sun8i_dwmac_get_syscon_from_dev(struct device_node *node) 1127 { 1128 struct device_node *syscon_node; 1129 struct platform_device *syscon_pdev; 1130 struct regmap *regmap = NULL; 1131 1132 syscon_node = of_parse_phandle(node, "syscon", 0); 1133 if (!syscon_node) 1134 return ERR_PTR(-ENODEV); 1135 1136 syscon_pdev = of_find_device_by_node(syscon_node); 1137 if (!syscon_pdev) { 1138 /* platform device might not be probed yet */ 1139 regmap = ERR_PTR(-EPROBE_DEFER); 1140 goto out_put_node; 1141 } 1142 1143 /* If no regmap is found then the other device driver is at fault */ 1144 regmap = dev_get_regmap(&syscon_pdev->dev, NULL); 1145 if (!regmap) 1146 regmap = ERR_PTR(-EINVAL); 1147 1148 platform_device_put(syscon_pdev); 1149 out_put_node: 1150 of_node_put(syscon_node); 1151 return regmap; 1152 } 1153 1154 static int sun8i_dwmac_probe(struct platform_device *pdev) 1155 { 1156 struct plat_stmmacenet_data *plat_dat; 1157 struct stmmac_resources stmmac_res; 1158 struct sunxi_priv_data *gmac; 1159 struct device *dev = &pdev->dev; 1160 phy_interface_t interface; 1161 int ret; 1162 struct stmmac_priv *priv; 1163 struct net_device *ndev; 1164 struct regmap *regmap; 1165 1166 ret = stmmac_get_platform_resources(pdev, &stmmac_res); 1167 if (ret) 1168 return ret; 1169 1170 gmac = devm_kzalloc(dev, sizeof(*gmac), GFP_KERNEL); 1171 if (!gmac) 1172 return -ENOMEM; 1173 1174 gmac->variant = of_device_get_match_data(&pdev->dev); 1175 if (!gmac->variant) { 1176 dev_err(&pdev->dev, "Missing dwmac-sun8i variant\n"); 1177 return -EINVAL; 1178 } 1179 1180 /* Optional regulator for PHY */ 1181 gmac->regulator = devm_regulator_get_optional(dev, "phy"); 1182 if (IS_ERR(gmac->regulator)) { 1183 if (PTR_ERR(gmac->regulator) == -EPROBE_DEFER) 1184 return -EPROBE_DEFER; 1185 dev_info(dev, "No regulator found\n"); 1186 gmac->regulator = NULL; 1187 } 1188 1189 /* The "GMAC clock control" register might be located in the 1190 * CCU address range (on the R40), or the system control address 1191 * range (on most other sun8i and later SoCs). 1192 * 1193 * The former controls most if not all clocks in the SoC. The 1194 * latter has an SoC identification register, and on some SoCs, 1195 * controls to map device specific SRAM to either the intended 1196 * peripheral, or the CPU address space. 1197 * 1198 * In either case, there should be a coordinated and restricted 1199 * method of accessing the register needed here. This is done by 1200 * having the device export a custom regmap, instead of a generic 1201 * syscon, which grants all access to all registers. 1202 * 1203 * To support old device trees, we fall back to using the syscon 1204 * interface if possible. 1205 */ 1206 regmap = sun8i_dwmac_get_syscon_from_dev(pdev->dev.of_node); 1207 if (IS_ERR(regmap)) 1208 regmap = syscon_regmap_lookup_by_phandle(pdev->dev.of_node, 1209 "syscon"); 1210 if (IS_ERR(regmap)) { 1211 ret = PTR_ERR(regmap); 1212 dev_err(&pdev->dev, "Unable to map syscon: %d\n", ret); 1213 return ret; 1214 } 1215 1216 gmac->regmap_field = devm_regmap_field_alloc(dev, regmap, 1217 *gmac->variant->syscon_field); 1218 if (IS_ERR(gmac->regmap_field)) { 1219 ret = PTR_ERR(gmac->regmap_field); 1220 dev_err(dev, "Unable to map syscon register: %d\n", ret); 1221 return ret; 1222 } 1223 1224 ret = of_get_phy_mode(dev->of_node, &interface); 1225 if (ret) 1226 return -EINVAL; 1227 1228 plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); 1229 if (IS_ERR(plat_dat)) 1230 return PTR_ERR(plat_dat); 1231 1232 /* platform data specifying hardware features and callbacks. 1233 * hardware features were copied from Allwinner drivers. 1234 */ 1235 plat_dat->mac_interface = interface; 1236 plat_dat->rx_coe = STMMAC_RX_COE_TYPE2; 1237 plat_dat->tx_coe = 1; 1238 plat_dat->flags |= STMMAC_FLAG_HAS_SUN8I; 1239 plat_dat->bsp_priv = gmac; 1240 plat_dat->init = sun8i_dwmac_init; 1241 plat_dat->exit = sun8i_dwmac_exit; 1242 plat_dat->setup = sun8i_dwmac_setup; 1243 plat_dat->tx_fifo_size = 4096; 1244 plat_dat->rx_fifo_size = 16384; 1245 1246 ret = sun8i_dwmac_set_syscon(&pdev->dev, plat_dat); 1247 if (ret) 1248 goto dwmac_deconfig; 1249 1250 ret = sun8i_dwmac_init(pdev, plat_dat->bsp_priv); 1251 if (ret) 1252 goto dwmac_syscon; 1253 1254 ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res); 1255 if (ret) 1256 goto dwmac_exit; 1257 1258 ndev = dev_get_drvdata(&pdev->dev); 1259 priv = netdev_priv(ndev); 1260 1261 /* the MAC is runtime suspended after stmmac_dvr_probe(), so we 1262 * need to ensure the MAC resume back before other operations such 1263 * as reset. 1264 */ 1265 pm_runtime_get_sync(&pdev->dev); 1266 1267 /* The mux must be registered after parent MDIO 1268 * so after stmmac_dvr_probe() 1269 */ 1270 if (gmac->variant->soc_has_internal_phy) { 1271 ret = get_ephy_nodes(priv); 1272 if (ret) 1273 goto dwmac_remove; 1274 ret = sun8i_dwmac_register_mdio_mux(priv); 1275 if (ret) { 1276 dev_err(&pdev->dev, "Failed to register mux\n"); 1277 goto dwmac_mux; 1278 } 1279 } else { 1280 ret = sun8i_dwmac_reset(priv); 1281 if (ret) 1282 goto dwmac_remove; 1283 } 1284 1285 pm_runtime_put(&pdev->dev); 1286 1287 return 0; 1288 1289 dwmac_mux: 1290 reset_control_put(gmac->rst_ephy); 1291 clk_put(gmac->ephy_clk); 1292 dwmac_remove: 1293 pm_runtime_put_noidle(&pdev->dev); 1294 stmmac_dvr_remove(&pdev->dev); 1295 dwmac_exit: 1296 sun8i_dwmac_exit(pdev, gmac); 1297 dwmac_syscon: 1298 sun8i_dwmac_unset_syscon(gmac); 1299 dwmac_deconfig: 1300 stmmac_remove_config_dt(pdev, plat_dat); 1301 1302 return ret; 1303 } 1304 1305 static void sun8i_dwmac_remove(struct platform_device *pdev) 1306 { 1307 struct net_device *ndev = platform_get_drvdata(pdev); 1308 struct stmmac_priv *priv = netdev_priv(ndev); 1309 struct sunxi_priv_data *gmac = priv->plat->bsp_priv; 1310 1311 if (gmac->variant->soc_has_internal_phy) { 1312 mdio_mux_uninit(gmac->mux_handle); 1313 sun8i_dwmac_unpower_internal_phy(gmac); 1314 reset_control_put(gmac->rst_ephy); 1315 clk_put(gmac->ephy_clk); 1316 } 1317 1318 stmmac_pltfr_remove(pdev); 1319 sun8i_dwmac_unset_syscon(gmac); 1320 } 1321 1322 static void sun8i_dwmac_shutdown(struct platform_device *pdev) 1323 { 1324 struct net_device *ndev = platform_get_drvdata(pdev); 1325 struct stmmac_priv *priv = netdev_priv(ndev); 1326 struct sunxi_priv_data *gmac = priv->plat->bsp_priv; 1327 1328 sun8i_dwmac_exit(pdev, gmac); 1329 } 1330 1331 static const struct of_device_id sun8i_dwmac_match[] = { 1332 { .compatible = "allwinner,sun8i-h3-emac", 1333 .data = &emac_variant_h3 }, 1334 { .compatible = "allwinner,sun8i-v3s-emac", 1335 .data = &emac_variant_v3s }, 1336 { .compatible = "allwinner,sun8i-a83t-emac", 1337 .data = &emac_variant_a83t }, 1338 { .compatible = "allwinner,sun8i-r40-gmac", 1339 .data = &emac_variant_r40 }, 1340 { .compatible = "allwinner,sun50i-a64-emac", 1341 .data = &emac_variant_a64 }, 1342 { .compatible = "allwinner,sun50i-h6-emac", 1343 .data = &emac_variant_h6 }, 1344 { } 1345 }; 1346 MODULE_DEVICE_TABLE(of, sun8i_dwmac_match); 1347 1348 static struct platform_driver sun8i_dwmac_driver = { 1349 .probe = sun8i_dwmac_probe, 1350 .remove_new = sun8i_dwmac_remove, 1351 .shutdown = sun8i_dwmac_shutdown, 1352 .driver = { 1353 .name = "dwmac-sun8i", 1354 .pm = &stmmac_pltfr_pm_ops, 1355 .of_match_table = sun8i_dwmac_match, 1356 }, 1357 }; 1358 module_platform_driver(sun8i_dwmac_driver); 1359 1360 MODULE_AUTHOR("Corentin Labbe <clabbe.montjoie@gmail.com>"); 1361 MODULE_DESCRIPTION("Allwinner sun8i DWMAC specific glue layer"); 1362 MODULE_LICENSE("GPL"); 1363