1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * dwmac-sun8i.c - Allwinner sun8i DWMAC specific glue layer 4 * 5 * Copyright (C) 2017 Corentin Labbe <clabbe.montjoie@gmail.com> 6 */ 7 8 #include <linux/clk.h> 9 #include <linux/io.h> 10 #include <linux/iopoll.h> 11 #include <linux/mdio-mux.h> 12 #include <linux/mfd/syscon.h> 13 #include <linux/module.h> 14 #include <linux/of_device.h> 15 #include <linux/of_mdio.h> 16 #include <linux/of_net.h> 17 #include <linux/phy.h> 18 #include <linux/platform_device.h> 19 #include <linux/pm_runtime.h> 20 #include <linux/regulator/consumer.h> 21 #include <linux/regmap.h> 22 #include <linux/stmmac.h> 23 24 #include "stmmac.h" 25 #include "stmmac_platform.h" 26 27 /* General notes on dwmac-sun8i: 28 * Locking: no locking is necessary in this file because all necessary locking 29 * is done in the "stmmac files" 30 */ 31 32 /* struct emac_variant - Describe dwmac-sun8i hardware variant 33 * @default_syscon_value: The default value of the EMAC register in syscon 34 * This value is used for disabling properly EMAC 35 * and used as a good starting value in case of the 36 * boot process(uboot) leave some stuff. 37 * @syscon_field reg_field for the syscon's gmac register 38 * @soc_has_internal_phy: Does the MAC embed an internal PHY 39 * @support_mii: Does the MAC handle MII 40 * @support_rmii: Does the MAC handle RMII 41 * @support_rgmii: Does the MAC handle RGMII 42 * 43 * @rx_delay_max: Maximum raw value for RX delay chain 44 * @tx_delay_max: Maximum raw value for TX delay chain 45 * These two also indicate the bitmask for 46 * the RX and TX delay chain registers. A 47 * value of zero indicates this is not supported. 48 */ 49 struct emac_variant { 50 u32 default_syscon_value; 51 const struct reg_field *syscon_field; 52 bool soc_has_internal_phy; 53 bool support_mii; 54 bool support_rmii; 55 bool support_rgmii; 56 u8 rx_delay_max; 57 u8 tx_delay_max; 58 }; 59 60 /* struct sunxi_priv_data - hold all sunxi private data 61 * @ephy_clk: reference to the optional EPHY clock for the internal PHY 62 * @regulator: reference to the optional regulator 63 * @rst_ephy: reference to the optional EPHY reset for the internal PHY 64 * @variant: reference to the current board variant 65 * @regmap: regmap for using the syscon 66 * @internal_phy_powered: Does the internal PHY is enabled 67 * @use_internal_phy: Is the internal PHY selected for use 68 * @mux_handle: Internal pointer used by mdio-mux lib 69 */ 70 struct sunxi_priv_data { 71 struct clk *ephy_clk; 72 struct regulator *regulator; 73 struct reset_control *rst_ephy; 74 const struct emac_variant *variant; 75 struct regmap_field *regmap_field; 76 bool internal_phy_powered; 77 bool use_internal_phy; 78 void *mux_handle; 79 }; 80 81 /* EMAC clock register @ 0x30 in the "system control" address range */ 82 static const struct reg_field sun8i_syscon_reg_field = { 83 .reg = 0x30, 84 .lsb = 0, 85 .msb = 31, 86 }; 87 88 /* EMAC clock register @ 0x164 in the CCU address range */ 89 static const struct reg_field sun8i_ccu_reg_field = { 90 .reg = 0x164, 91 .lsb = 0, 92 .msb = 31, 93 }; 94 95 static const struct emac_variant emac_variant_h3 = { 96 .default_syscon_value = 0x58000, 97 .syscon_field = &sun8i_syscon_reg_field, 98 .soc_has_internal_phy = true, 99 .support_mii = true, 100 .support_rmii = true, 101 .support_rgmii = true, 102 .rx_delay_max = 31, 103 .tx_delay_max = 7, 104 }; 105 106 static const struct emac_variant emac_variant_v3s = { 107 .default_syscon_value = 0x38000, 108 .syscon_field = &sun8i_syscon_reg_field, 109 .soc_has_internal_phy = true, 110 .support_mii = true 111 }; 112 113 static const struct emac_variant emac_variant_a83t = { 114 .default_syscon_value = 0, 115 .syscon_field = &sun8i_syscon_reg_field, 116 .soc_has_internal_phy = false, 117 .support_mii = true, 118 .support_rgmii = true, 119 .rx_delay_max = 31, 120 .tx_delay_max = 7, 121 }; 122 123 static const struct emac_variant emac_variant_r40 = { 124 .default_syscon_value = 0, 125 .syscon_field = &sun8i_ccu_reg_field, 126 .support_mii = true, 127 .support_rgmii = true, 128 .rx_delay_max = 7, 129 }; 130 131 static const struct emac_variant emac_variant_a64 = { 132 .default_syscon_value = 0, 133 .syscon_field = &sun8i_syscon_reg_field, 134 .soc_has_internal_phy = false, 135 .support_mii = true, 136 .support_rmii = true, 137 .support_rgmii = true, 138 .rx_delay_max = 31, 139 .tx_delay_max = 7, 140 }; 141 142 static const struct emac_variant emac_variant_h6 = { 143 .default_syscon_value = 0x50000, 144 .syscon_field = &sun8i_syscon_reg_field, 145 /* The "Internal PHY" of H6 is not on the die. It's on the 146 * co-packaged AC200 chip instead. 147 */ 148 .soc_has_internal_phy = false, 149 .support_mii = true, 150 .support_rmii = true, 151 .support_rgmii = true, 152 .rx_delay_max = 31, 153 .tx_delay_max = 7, 154 }; 155 156 #define EMAC_BASIC_CTL0 0x00 157 #define EMAC_BASIC_CTL1 0x04 158 #define EMAC_INT_STA 0x08 159 #define EMAC_INT_EN 0x0C 160 #define EMAC_TX_CTL0 0x10 161 #define EMAC_TX_CTL1 0x14 162 #define EMAC_TX_FLOW_CTL 0x1C 163 #define EMAC_TX_DESC_LIST 0x20 164 #define EMAC_RX_CTL0 0x24 165 #define EMAC_RX_CTL1 0x28 166 #define EMAC_RX_DESC_LIST 0x34 167 #define EMAC_RX_FRM_FLT 0x38 168 #define EMAC_MDIO_CMD 0x48 169 #define EMAC_MDIO_DATA 0x4C 170 #define EMAC_MACADDR_HI(reg) (0x50 + (reg) * 8) 171 #define EMAC_MACADDR_LO(reg) (0x54 + (reg) * 8) 172 #define EMAC_TX_DMA_STA 0xB0 173 #define EMAC_TX_CUR_DESC 0xB4 174 #define EMAC_TX_CUR_BUF 0xB8 175 #define EMAC_RX_DMA_STA 0xC0 176 #define EMAC_RX_CUR_DESC 0xC4 177 #define EMAC_RX_CUR_BUF 0xC8 178 179 /* Use in EMAC_BASIC_CTL0 */ 180 #define EMAC_DUPLEX_FULL BIT(0) 181 #define EMAC_LOOPBACK BIT(1) 182 #define EMAC_SPEED_1000 0 183 #define EMAC_SPEED_100 (0x03 << 2) 184 #define EMAC_SPEED_10 (0x02 << 2) 185 186 /* Use in EMAC_BASIC_CTL1 */ 187 #define EMAC_BURSTLEN_SHIFT 24 188 189 /* Used in EMAC_RX_FRM_FLT */ 190 #define EMAC_FRM_FLT_RXALL BIT(0) 191 #define EMAC_FRM_FLT_CTL BIT(13) 192 #define EMAC_FRM_FLT_MULTICAST BIT(16) 193 194 /* Used in RX_CTL1*/ 195 #define EMAC_RX_MD BIT(1) 196 #define EMAC_RX_TH_MASK GENMASK(5, 4) 197 #define EMAC_RX_TH_32 0 198 #define EMAC_RX_TH_64 (0x1 << 4) 199 #define EMAC_RX_TH_96 (0x2 << 4) 200 #define EMAC_RX_TH_128 (0x3 << 4) 201 #define EMAC_RX_DMA_EN BIT(30) 202 #define EMAC_RX_DMA_START BIT(31) 203 204 /* Used in TX_CTL1*/ 205 #define EMAC_TX_MD BIT(1) 206 #define EMAC_TX_NEXT_FRM BIT(2) 207 #define EMAC_TX_TH_MASK GENMASK(10, 8) 208 #define EMAC_TX_TH_64 0 209 #define EMAC_TX_TH_128 (0x1 << 8) 210 #define EMAC_TX_TH_192 (0x2 << 8) 211 #define EMAC_TX_TH_256 (0x3 << 8) 212 #define EMAC_TX_DMA_EN BIT(30) 213 #define EMAC_TX_DMA_START BIT(31) 214 215 /* Used in RX_CTL0 */ 216 #define EMAC_RX_RECEIVER_EN BIT(31) 217 #define EMAC_RX_DO_CRC BIT(27) 218 #define EMAC_RX_FLOW_CTL_EN BIT(16) 219 220 /* Used in TX_CTL0 */ 221 #define EMAC_TX_TRANSMITTER_EN BIT(31) 222 223 /* Used in EMAC_TX_FLOW_CTL */ 224 #define EMAC_TX_FLOW_CTL_EN BIT(0) 225 226 /* Used in EMAC_INT_STA */ 227 #define EMAC_TX_INT BIT(0) 228 #define EMAC_TX_DMA_STOP_INT BIT(1) 229 #define EMAC_TX_BUF_UA_INT BIT(2) 230 #define EMAC_TX_TIMEOUT_INT BIT(3) 231 #define EMAC_TX_UNDERFLOW_INT BIT(4) 232 #define EMAC_TX_EARLY_INT BIT(5) 233 #define EMAC_RX_INT BIT(8) 234 #define EMAC_RX_BUF_UA_INT BIT(9) 235 #define EMAC_RX_DMA_STOP_INT BIT(10) 236 #define EMAC_RX_TIMEOUT_INT BIT(11) 237 #define EMAC_RX_OVERFLOW_INT BIT(12) 238 #define EMAC_RX_EARLY_INT BIT(13) 239 #define EMAC_RGMII_STA_INT BIT(16) 240 241 #define EMAC_INT_MSK_COMMON EMAC_RGMII_STA_INT 242 #define EMAC_INT_MSK_TX (EMAC_TX_INT | \ 243 EMAC_TX_DMA_STOP_INT | \ 244 EMAC_TX_BUF_UA_INT | \ 245 EMAC_TX_TIMEOUT_INT | \ 246 EMAC_TX_UNDERFLOW_INT | \ 247 EMAC_TX_EARLY_INT |\ 248 EMAC_INT_MSK_COMMON) 249 #define EMAC_INT_MSK_RX (EMAC_RX_INT | \ 250 EMAC_RX_BUF_UA_INT | \ 251 EMAC_RX_DMA_STOP_INT | \ 252 EMAC_RX_TIMEOUT_INT | \ 253 EMAC_RX_OVERFLOW_INT | \ 254 EMAC_RX_EARLY_INT | \ 255 EMAC_INT_MSK_COMMON) 256 257 #define MAC_ADDR_TYPE_DST BIT(31) 258 259 /* H3 specific bits for EPHY */ 260 #define H3_EPHY_ADDR_SHIFT 20 261 #define H3_EPHY_CLK_SEL BIT(18) /* 1: 24MHz, 0: 25MHz */ 262 #define H3_EPHY_LED_POL BIT(17) /* 1: active low, 0: active high */ 263 #define H3_EPHY_SHUTDOWN BIT(16) /* 1: shutdown, 0: power up */ 264 #define H3_EPHY_SELECT BIT(15) /* 1: internal PHY, 0: external PHY */ 265 #define H3_EPHY_MUX_MASK (H3_EPHY_SHUTDOWN | H3_EPHY_SELECT) 266 #define DWMAC_SUN8I_MDIO_MUX_INTERNAL_ID 1 267 #define DWMAC_SUN8I_MDIO_MUX_EXTERNAL_ID 2 268 269 /* H3/A64 specific bits */ 270 #define SYSCON_RMII_EN BIT(13) /* 1: enable RMII (overrides EPIT) */ 271 272 /* Generic system control EMAC_CLK bits */ 273 #define SYSCON_ETXDC_SHIFT 10 274 #define SYSCON_ERXDC_SHIFT 5 275 /* EMAC PHY Interface Type */ 276 #define SYSCON_EPIT BIT(2) /* 1: RGMII, 0: MII */ 277 #define SYSCON_ETCS_MASK GENMASK(1, 0) 278 #define SYSCON_ETCS_MII 0x0 279 #define SYSCON_ETCS_EXT_GMII 0x1 280 #define SYSCON_ETCS_INT_GMII 0x2 281 282 /* sun8i_dwmac_dma_reset() - reset the EMAC 283 * Called from stmmac via stmmac_dma_ops->reset 284 */ 285 static int sun8i_dwmac_dma_reset(void __iomem *ioaddr) 286 { 287 writel(0, ioaddr + EMAC_RX_CTL1); 288 writel(0, ioaddr + EMAC_TX_CTL1); 289 writel(0, ioaddr + EMAC_RX_FRM_FLT); 290 writel(0, ioaddr + EMAC_RX_DESC_LIST); 291 writel(0, ioaddr + EMAC_TX_DESC_LIST); 292 writel(0, ioaddr + EMAC_INT_EN); 293 writel(0x1FFFFFF, ioaddr + EMAC_INT_STA); 294 return 0; 295 } 296 297 /* sun8i_dwmac_dma_init() - initialize the EMAC 298 * Called from stmmac via stmmac_dma_ops->init 299 */ 300 static void sun8i_dwmac_dma_init(void __iomem *ioaddr, 301 struct stmmac_dma_cfg *dma_cfg, int atds) 302 { 303 writel(EMAC_RX_INT | EMAC_TX_INT, ioaddr + EMAC_INT_EN); 304 writel(0x1FFFFFF, ioaddr + EMAC_INT_STA); 305 } 306 307 static void sun8i_dwmac_dma_init_rx(void __iomem *ioaddr, 308 struct stmmac_dma_cfg *dma_cfg, 309 dma_addr_t dma_rx_phy, u32 chan) 310 { 311 /* Write RX descriptors address */ 312 writel(lower_32_bits(dma_rx_phy), ioaddr + EMAC_RX_DESC_LIST); 313 } 314 315 static void sun8i_dwmac_dma_init_tx(void __iomem *ioaddr, 316 struct stmmac_dma_cfg *dma_cfg, 317 dma_addr_t dma_tx_phy, u32 chan) 318 { 319 /* Write TX descriptors address */ 320 writel(lower_32_bits(dma_tx_phy), ioaddr + EMAC_TX_DESC_LIST); 321 } 322 323 /* sun8i_dwmac_dump_regs() - Dump EMAC address space 324 * Called from stmmac_dma_ops->dump_regs 325 * Used for ethtool 326 */ 327 static void sun8i_dwmac_dump_regs(void __iomem *ioaddr, u32 *reg_space) 328 { 329 int i; 330 331 for (i = 0; i < 0xC8; i += 4) { 332 if (i == 0x32 || i == 0x3C) 333 continue; 334 reg_space[i / 4] = readl(ioaddr + i); 335 } 336 } 337 338 /* sun8i_dwmac_dump_mac_regs() - Dump EMAC address space 339 * Called from stmmac_ops->dump_regs 340 * Used for ethtool 341 */ 342 static void sun8i_dwmac_dump_mac_regs(struct mac_device_info *hw, 343 u32 *reg_space) 344 { 345 int i; 346 void __iomem *ioaddr = hw->pcsr; 347 348 for (i = 0; i < 0xC8; i += 4) { 349 if (i == 0x32 || i == 0x3C) 350 continue; 351 reg_space[i / 4] = readl(ioaddr + i); 352 } 353 } 354 355 static void sun8i_dwmac_enable_dma_irq(void __iomem *ioaddr, u32 chan, 356 bool rx, bool tx) 357 { 358 u32 value = readl(ioaddr + EMAC_INT_EN); 359 360 if (rx) 361 value |= EMAC_RX_INT; 362 if (tx) 363 value |= EMAC_TX_INT; 364 365 writel(value, ioaddr + EMAC_INT_EN); 366 } 367 368 static void sun8i_dwmac_disable_dma_irq(void __iomem *ioaddr, u32 chan, 369 bool rx, bool tx) 370 { 371 u32 value = readl(ioaddr + EMAC_INT_EN); 372 373 if (rx) 374 value &= ~EMAC_RX_INT; 375 if (tx) 376 value &= ~EMAC_TX_INT; 377 378 writel(value, ioaddr + EMAC_INT_EN); 379 } 380 381 static void sun8i_dwmac_dma_start_tx(void __iomem *ioaddr, u32 chan) 382 { 383 u32 v; 384 385 v = readl(ioaddr + EMAC_TX_CTL1); 386 v |= EMAC_TX_DMA_START; 387 v |= EMAC_TX_DMA_EN; 388 writel(v, ioaddr + EMAC_TX_CTL1); 389 } 390 391 static void sun8i_dwmac_enable_dma_transmission(void __iomem *ioaddr) 392 { 393 u32 v; 394 395 v = readl(ioaddr + EMAC_TX_CTL1); 396 v |= EMAC_TX_DMA_START; 397 v |= EMAC_TX_DMA_EN; 398 writel(v, ioaddr + EMAC_TX_CTL1); 399 } 400 401 static void sun8i_dwmac_dma_stop_tx(void __iomem *ioaddr, u32 chan) 402 { 403 u32 v; 404 405 v = readl(ioaddr + EMAC_TX_CTL1); 406 v &= ~EMAC_TX_DMA_EN; 407 writel(v, ioaddr + EMAC_TX_CTL1); 408 } 409 410 static void sun8i_dwmac_dma_start_rx(void __iomem *ioaddr, u32 chan) 411 { 412 u32 v; 413 414 v = readl(ioaddr + EMAC_RX_CTL1); 415 v |= EMAC_RX_DMA_START; 416 v |= EMAC_RX_DMA_EN; 417 writel(v, ioaddr + EMAC_RX_CTL1); 418 } 419 420 static void sun8i_dwmac_dma_stop_rx(void __iomem *ioaddr, u32 chan) 421 { 422 u32 v; 423 424 v = readl(ioaddr + EMAC_RX_CTL1); 425 v &= ~EMAC_RX_DMA_EN; 426 writel(v, ioaddr + EMAC_RX_CTL1); 427 } 428 429 static int sun8i_dwmac_dma_interrupt(void __iomem *ioaddr, 430 struct stmmac_extra_stats *x, u32 chan, 431 u32 dir) 432 { 433 u32 v; 434 int ret = 0; 435 436 v = readl(ioaddr + EMAC_INT_STA); 437 438 if (dir == DMA_DIR_RX) 439 v &= EMAC_INT_MSK_RX; 440 else if (dir == DMA_DIR_TX) 441 v &= EMAC_INT_MSK_TX; 442 443 if (v & EMAC_TX_INT) { 444 ret |= handle_tx; 445 x->tx_normal_irq_n++; 446 } 447 448 if (v & EMAC_TX_DMA_STOP_INT) 449 x->tx_process_stopped_irq++; 450 451 if (v & EMAC_TX_BUF_UA_INT) 452 x->tx_process_stopped_irq++; 453 454 if (v & EMAC_TX_TIMEOUT_INT) 455 ret |= tx_hard_error; 456 457 if (v & EMAC_TX_UNDERFLOW_INT) { 458 ret |= tx_hard_error; 459 x->tx_undeflow_irq++; 460 } 461 462 if (v & EMAC_TX_EARLY_INT) 463 x->tx_early_irq++; 464 465 if (v & EMAC_RX_INT) { 466 ret |= handle_rx; 467 x->rx_normal_irq_n++; 468 } 469 470 if (v & EMAC_RX_BUF_UA_INT) 471 x->rx_buf_unav_irq++; 472 473 if (v & EMAC_RX_DMA_STOP_INT) 474 x->rx_process_stopped_irq++; 475 476 if (v & EMAC_RX_TIMEOUT_INT) 477 ret |= tx_hard_error; 478 479 if (v & EMAC_RX_OVERFLOW_INT) { 480 ret |= tx_hard_error; 481 x->rx_overflow_irq++; 482 } 483 484 if (v & EMAC_RX_EARLY_INT) 485 x->rx_early_irq++; 486 487 if (v & EMAC_RGMII_STA_INT) 488 x->irq_rgmii_n++; 489 490 writel(v, ioaddr + EMAC_INT_STA); 491 492 return ret; 493 } 494 495 static void sun8i_dwmac_dma_operation_mode_rx(void __iomem *ioaddr, int mode, 496 u32 channel, int fifosz, u8 qmode) 497 { 498 u32 v; 499 500 v = readl(ioaddr + EMAC_RX_CTL1); 501 if (mode == SF_DMA_MODE) { 502 v |= EMAC_RX_MD; 503 } else { 504 v &= ~EMAC_RX_MD; 505 v &= ~EMAC_RX_TH_MASK; 506 if (mode < 32) 507 v |= EMAC_RX_TH_32; 508 else if (mode < 64) 509 v |= EMAC_RX_TH_64; 510 else if (mode < 96) 511 v |= EMAC_RX_TH_96; 512 else if (mode < 128) 513 v |= EMAC_RX_TH_128; 514 } 515 writel(v, ioaddr + EMAC_RX_CTL1); 516 } 517 518 static void sun8i_dwmac_dma_operation_mode_tx(void __iomem *ioaddr, int mode, 519 u32 channel, int fifosz, u8 qmode) 520 { 521 u32 v; 522 523 v = readl(ioaddr + EMAC_TX_CTL1); 524 if (mode == SF_DMA_MODE) { 525 v |= EMAC_TX_MD; 526 /* Undocumented bit (called TX_NEXT_FRM in BSP), the original 527 * comment is 528 * "Operating on second frame increase the performance 529 * especially when transmit store-and-forward is used." 530 */ 531 v |= EMAC_TX_NEXT_FRM; 532 } else { 533 v &= ~EMAC_TX_MD; 534 v &= ~EMAC_TX_TH_MASK; 535 if (mode < 64) 536 v |= EMAC_TX_TH_64; 537 else if (mode < 128) 538 v |= EMAC_TX_TH_128; 539 else if (mode < 192) 540 v |= EMAC_TX_TH_192; 541 else if (mode < 256) 542 v |= EMAC_TX_TH_256; 543 } 544 writel(v, ioaddr + EMAC_TX_CTL1); 545 } 546 547 static const struct stmmac_dma_ops sun8i_dwmac_dma_ops = { 548 .reset = sun8i_dwmac_dma_reset, 549 .init = sun8i_dwmac_dma_init, 550 .init_rx_chan = sun8i_dwmac_dma_init_rx, 551 .init_tx_chan = sun8i_dwmac_dma_init_tx, 552 .dump_regs = sun8i_dwmac_dump_regs, 553 .dma_rx_mode = sun8i_dwmac_dma_operation_mode_rx, 554 .dma_tx_mode = sun8i_dwmac_dma_operation_mode_tx, 555 .enable_dma_transmission = sun8i_dwmac_enable_dma_transmission, 556 .enable_dma_irq = sun8i_dwmac_enable_dma_irq, 557 .disable_dma_irq = sun8i_dwmac_disable_dma_irq, 558 .start_tx = sun8i_dwmac_dma_start_tx, 559 .stop_tx = sun8i_dwmac_dma_stop_tx, 560 .start_rx = sun8i_dwmac_dma_start_rx, 561 .stop_rx = sun8i_dwmac_dma_stop_rx, 562 .dma_interrupt = sun8i_dwmac_dma_interrupt, 563 }; 564 565 static int sun8i_dwmac_power_internal_phy(struct stmmac_priv *priv); 566 567 static int sun8i_dwmac_init(struct platform_device *pdev, void *priv) 568 { 569 struct net_device *ndev = platform_get_drvdata(pdev); 570 struct sunxi_priv_data *gmac = priv; 571 int ret; 572 573 if (gmac->regulator) { 574 ret = regulator_enable(gmac->regulator); 575 if (ret) { 576 dev_err(&pdev->dev, "Fail to enable regulator\n"); 577 return ret; 578 } 579 } 580 581 if (gmac->use_internal_phy) { 582 ret = sun8i_dwmac_power_internal_phy(netdev_priv(ndev)); 583 if (ret) 584 goto err_disable_regulator; 585 } 586 587 return 0; 588 589 err_disable_regulator: 590 if (gmac->regulator) 591 regulator_disable(gmac->regulator); 592 593 return ret; 594 } 595 596 static void sun8i_dwmac_core_init(struct mac_device_info *hw, 597 struct net_device *dev) 598 { 599 void __iomem *ioaddr = hw->pcsr; 600 u32 v; 601 602 v = (8 << EMAC_BURSTLEN_SHIFT); /* burst len */ 603 writel(v, ioaddr + EMAC_BASIC_CTL1); 604 } 605 606 static void sun8i_dwmac_set_mac(void __iomem *ioaddr, bool enable) 607 { 608 u32 t, r; 609 610 t = readl(ioaddr + EMAC_TX_CTL0); 611 r = readl(ioaddr + EMAC_RX_CTL0); 612 if (enable) { 613 t |= EMAC_TX_TRANSMITTER_EN; 614 r |= EMAC_RX_RECEIVER_EN; 615 } else { 616 t &= ~EMAC_TX_TRANSMITTER_EN; 617 r &= ~EMAC_RX_RECEIVER_EN; 618 } 619 writel(t, ioaddr + EMAC_TX_CTL0); 620 writel(r, ioaddr + EMAC_RX_CTL0); 621 } 622 623 /* Set MAC address at slot reg_n 624 * All slot > 0 need to be enabled with MAC_ADDR_TYPE_DST 625 * If addr is NULL, clear the slot 626 */ 627 static void sun8i_dwmac_set_umac_addr(struct mac_device_info *hw, 628 const unsigned char *addr, 629 unsigned int reg_n) 630 { 631 void __iomem *ioaddr = hw->pcsr; 632 u32 v; 633 634 if (!addr) { 635 writel(0, ioaddr + EMAC_MACADDR_HI(reg_n)); 636 return; 637 } 638 639 stmmac_set_mac_addr(ioaddr, addr, EMAC_MACADDR_HI(reg_n), 640 EMAC_MACADDR_LO(reg_n)); 641 if (reg_n > 0) { 642 v = readl(ioaddr + EMAC_MACADDR_HI(reg_n)); 643 v |= MAC_ADDR_TYPE_DST; 644 writel(v, ioaddr + EMAC_MACADDR_HI(reg_n)); 645 } 646 } 647 648 static void sun8i_dwmac_get_umac_addr(struct mac_device_info *hw, 649 unsigned char *addr, 650 unsigned int reg_n) 651 { 652 void __iomem *ioaddr = hw->pcsr; 653 654 stmmac_get_mac_addr(ioaddr, addr, EMAC_MACADDR_HI(reg_n), 655 EMAC_MACADDR_LO(reg_n)); 656 } 657 658 /* caution this function must return non 0 to work */ 659 static int sun8i_dwmac_rx_ipc_enable(struct mac_device_info *hw) 660 { 661 void __iomem *ioaddr = hw->pcsr; 662 u32 v; 663 664 v = readl(ioaddr + EMAC_RX_CTL0); 665 v |= EMAC_RX_DO_CRC; 666 writel(v, ioaddr + EMAC_RX_CTL0); 667 668 return 1; 669 } 670 671 static void sun8i_dwmac_set_filter(struct mac_device_info *hw, 672 struct net_device *dev) 673 { 674 void __iomem *ioaddr = hw->pcsr; 675 u32 v; 676 int i = 1; 677 struct netdev_hw_addr *ha; 678 int macaddrs = netdev_uc_count(dev) + netdev_mc_count(dev) + 1; 679 680 v = EMAC_FRM_FLT_CTL; 681 682 if (dev->flags & IFF_PROMISC) { 683 v = EMAC_FRM_FLT_RXALL; 684 } else if (dev->flags & IFF_ALLMULTI) { 685 v |= EMAC_FRM_FLT_MULTICAST; 686 } else if (macaddrs <= hw->unicast_filter_entries) { 687 if (!netdev_mc_empty(dev)) { 688 netdev_for_each_mc_addr(ha, dev) { 689 sun8i_dwmac_set_umac_addr(hw, ha->addr, i); 690 i++; 691 } 692 } 693 if (!netdev_uc_empty(dev)) { 694 netdev_for_each_uc_addr(ha, dev) { 695 sun8i_dwmac_set_umac_addr(hw, ha->addr, i); 696 i++; 697 } 698 } 699 } else { 700 if (!(readl(ioaddr + EMAC_RX_FRM_FLT) & EMAC_FRM_FLT_RXALL)) 701 netdev_info(dev, "Too many address, switching to promiscuous\n"); 702 v = EMAC_FRM_FLT_RXALL; 703 } 704 705 /* Disable unused address filter slots */ 706 while (i < hw->unicast_filter_entries) 707 sun8i_dwmac_set_umac_addr(hw, NULL, i++); 708 709 writel(v, ioaddr + EMAC_RX_FRM_FLT); 710 } 711 712 static void sun8i_dwmac_flow_ctrl(struct mac_device_info *hw, 713 unsigned int duplex, unsigned int fc, 714 unsigned int pause_time, u32 tx_cnt) 715 { 716 void __iomem *ioaddr = hw->pcsr; 717 u32 v; 718 719 v = readl(ioaddr + EMAC_RX_CTL0); 720 if (fc == FLOW_AUTO) 721 v |= EMAC_RX_FLOW_CTL_EN; 722 else 723 v &= ~EMAC_RX_FLOW_CTL_EN; 724 writel(v, ioaddr + EMAC_RX_CTL0); 725 726 v = readl(ioaddr + EMAC_TX_FLOW_CTL); 727 if (fc == FLOW_AUTO) 728 v |= EMAC_TX_FLOW_CTL_EN; 729 else 730 v &= ~EMAC_TX_FLOW_CTL_EN; 731 writel(v, ioaddr + EMAC_TX_FLOW_CTL); 732 } 733 734 static int sun8i_dwmac_reset(struct stmmac_priv *priv) 735 { 736 u32 v; 737 int err; 738 739 v = readl(priv->ioaddr + EMAC_BASIC_CTL1); 740 writel(v | 0x01, priv->ioaddr + EMAC_BASIC_CTL1); 741 742 /* The timeout was previoulsy set to 10ms, but some board (OrangePI0) 743 * need more if no cable plugged. 100ms seems OK 744 */ 745 err = readl_poll_timeout(priv->ioaddr + EMAC_BASIC_CTL1, v, 746 !(v & 0x01), 100, 100000); 747 748 if (err) { 749 dev_err(priv->device, "EMAC reset timeout\n"); 750 return err; 751 } 752 return 0; 753 } 754 755 /* Search in mdio-mux node for internal PHY node and get its clk/reset */ 756 static int get_ephy_nodes(struct stmmac_priv *priv) 757 { 758 struct sunxi_priv_data *gmac = priv->plat->bsp_priv; 759 struct device_node *mdio_mux, *iphynode; 760 struct device_node *mdio_internal; 761 int ret; 762 763 mdio_mux = of_get_child_by_name(priv->device->of_node, "mdio-mux"); 764 if (!mdio_mux) { 765 dev_err(priv->device, "Cannot get mdio-mux node\n"); 766 return -ENODEV; 767 } 768 769 mdio_internal = of_get_compatible_child(mdio_mux, 770 "allwinner,sun8i-h3-mdio-internal"); 771 of_node_put(mdio_mux); 772 if (!mdio_internal) { 773 dev_err(priv->device, "Cannot get internal_mdio node\n"); 774 return -ENODEV; 775 } 776 777 /* Seek for internal PHY */ 778 for_each_child_of_node(mdio_internal, iphynode) { 779 gmac->ephy_clk = of_clk_get(iphynode, 0); 780 if (IS_ERR(gmac->ephy_clk)) 781 continue; 782 gmac->rst_ephy = of_reset_control_get_exclusive(iphynode, NULL); 783 if (IS_ERR(gmac->rst_ephy)) { 784 ret = PTR_ERR(gmac->rst_ephy); 785 if (ret == -EPROBE_DEFER) { 786 of_node_put(iphynode); 787 of_node_put(mdio_internal); 788 return ret; 789 } 790 continue; 791 } 792 dev_info(priv->device, "Found internal PHY node\n"); 793 of_node_put(iphynode); 794 of_node_put(mdio_internal); 795 return 0; 796 } 797 798 of_node_put(mdio_internal); 799 return -ENODEV; 800 } 801 802 static int sun8i_dwmac_power_internal_phy(struct stmmac_priv *priv) 803 { 804 struct sunxi_priv_data *gmac = priv->plat->bsp_priv; 805 int ret; 806 807 if (gmac->internal_phy_powered) { 808 dev_warn(priv->device, "Internal PHY already powered\n"); 809 return 0; 810 } 811 812 dev_info(priv->device, "Powering internal PHY\n"); 813 ret = clk_prepare_enable(gmac->ephy_clk); 814 if (ret) { 815 dev_err(priv->device, "Cannot enable internal PHY\n"); 816 return ret; 817 } 818 819 /* Make sure the EPHY is properly reseted, as U-Boot may leave 820 * it at deasserted state, and thus it may fail to reset EMAC. 821 * 822 * This assumes the driver has exclusive access to the EPHY reset. 823 */ 824 ret = reset_control_reset(gmac->rst_ephy); 825 if (ret) { 826 dev_err(priv->device, "Cannot reset internal PHY\n"); 827 clk_disable_unprepare(gmac->ephy_clk); 828 return ret; 829 } 830 831 gmac->internal_phy_powered = true; 832 833 return 0; 834 } 835 836 static void sun8i_dwmac_unpower_internal_phy(struct sunxi_priv_data *gmac) 837 { 838 if (!gmac->internal_phy_powered) 839 return; 840 841 clk_disable_unprepare(gmac->ephy_clk); 842 reset_control_assert(gmac->rst_ephy); 843 gmac->internal_phy_powered = false; 844 } 845 846 /* MDIO multiplexing switch function 847 * This function is called by the mdio-mux layer when it thinks the mdio bus 848 * multiplexer needs to switch. 849 * 'current_child' is the current value of the mux register 850 * 'desired_child' is the value of the 'reg' property of the target child MDIO 851 * node. 852 * The first time this function is called, current_child == -1. 853 * If current_child == desired_child, then the mux is already set to the 854 * correct bus. 855 */ 856 static int mdio_mux_syscon_switch_fn(int current_child, int desired_child, 857 void *data) 858 { 859 struct stmmac_priv *priv = data; 860 struct sunxi_priv_data *gmac = priv->plat->bsp_priv; 861 u32 reg, val; 862 int ret = 0; 863 864 if (current_child ^ desired_child) { 865 regmap_field_read(gmac->regmap_field, ®); 866 switch (desired_child) { 867 case DWMAC_SUN8I_MDIO_MUX_INTERNAL_ID: 868 dev_info(priv->device, "Switch mux to internal PHY"); 869 val = (reg & ~H3_EPHY_MUX_MASK) | H3_EPHY_SELECT; 870 gmac->use_internal_phy = true; 871 break; 872 case DWMAC_SUN8I_MDIO_MUX_EXTERNAL_ID: 873 dev_info(priv->device, "Switch mux to external PHY"); 874 val = (reg & ~H3_EPHY_MUX_MASK) | H3_EPHY_SHUTDOWN; 875 gmac->use_internal_phy = false; 876 break; 877 default: 878 dev_err(priv->device, "Invalid child ID %x\n", 879 desired_child); 880 return -EINVAL; 881 } 882 regmap_field_write(gmac->regmap_field, val); 883 if (gmac->use_internal_phy) { 884 ret = sun8i_dwmac_power_internal_phy(priv); 885 if (ret) 886 return ret; 887 } else { 888 sun8i_dwmac_unpower_internal_phy(gmac); 889 } 890 /* After changing syscon value, the MAC need reset or it will 891 * use the last value (and so the last PHY set). 892 */ 893 ret = sun8i_dwmac_reset(priv); 894 } 895 return ret; 896 } 897 898 static int sun8i_dwmac_register_mdio_mux(struct stmmac_priv *priv) 899 { 900 int ret; 901 struct device_node *mdio_mux; 902 struct sunxi_priv_data *gmac = priv->plat->bsp_priv; 903 904 mdio_mux = of_get_child_by_name(priv->device->of_node, "mdio-mux"); 905 if (!mdio_mux) 906 return -ENODEV; 907 908 ret = mdio_mux_init(priv->device, mdio_mux, mdio_mux_syscon_switch_fn, 909 &gmac->mux_handle, priv, priv->mii); 910 return ret; 911 } 912 913 static int sun8i_dwmac_set_syscon(struct device *dev, 914 struct plat_stmmacenet_data *plat) 915 { 916 struct sunxi_priv_data *gmac = plat->bsp_priv; 917 struct device_node *node = dev->of_node; 918 int ret; 919 u32 reg, val; 920 921 ret = regmap_field_read(gmac->regmap_field, &val); 922 if (ret) { 923 dev_err(dev, "Fail to read from regmap field.\n"); 924 return ret; 925 } 926 927 reg = gmac->variant->default_syscon_value; 928 if (reg != val) 929 dev_warn(dev, 930 "Current syscon value is not the default %x (expect %x)\n", 931 val, reg); 932 933 if (gmac->variant->soc_has_internal_phy) { 934 if (of_property_read_bool(node, "allwinner,leds-active-low")) 935 reg |= H3_EPHY_LED_POL; 936 else 937 reg &= ~H3_EPHY_LED_POL; 938 939 /* Force EPHY xtal frequency to 24MHz. */ 940 reg |= H3_EPHY_CLK_SEL; 941 942 ret = of_mdio_parse_addr(dev, plat->phy_node); 943 if (ret < 0) { 944 dev_err(dev, "Could not parse MDIO addr\n"); 945 return ret; 946 } 947 /* of_mdio_parse_addr returns a valid (0 ~ 31) PHY 948 * address. No need to mask it again. 949 */ 950 reg |= 1 << H3_EPHY_ADDR_SHIFT; 951 } else { 952 /* For SoCs without internal PHY the PHY selection bit should be 953 * set to 0 (external PHY). 954 */ 955 reg &= ~H3_EPHY_SELECT; 956 } 957 958 if (!of_property_read_u32(node, "allwinner,tx-delay-ps", &val)) { 959 if (val % 100) { 960 dev_err(dev, "tx-delay must be a multiple of 100\n"); 961 return -EINVAL; 962 } 963 val /= 100; 964 dev_dbg(dev, "set tx-delay to %x\n", val); 965 if (val <= gmac->variant->tx_delay_max) { 966 reg &= ~(gmac->variant->tx_delay_max << 967 SYSCON_ETXDC_SHIFT); 968 reg |= (val << SYSCON_ETXDC_SHIFT); 969 } else { 970 dev_err(dev, "Invalid TX clock delay: %d\n", 971 val); 972 return -EINVAL; 973 } 974 } 975 976 if (!of_property_read_u32(node, "allwinner,rx-delay-ps", &val)) { 977 if (val % 100) { 978 dev_err(dev, "rx-delay must be a multiple of 100\n"); 979 return -EINVAL; 980 } 981 val /= 100; 982 dev_dbg(dev, "set rx-delay to %x\n", val); 983 if (val <= gmac->variant->rx_delay_max) { 984 reg &= ~(gmac->variant->rx_delay_max << 985 SYSCON_ERXDC_SHIFT); 986 reg |= (val << SYSCON_ERXDC_SHIFT); 987 } else { 988 dev_err(dev, "Invalid RX clock delay: %d\n", 989 val); 990 return -EINVAL; 991 } 992 } 993 994 /* Clear interface mode bits */ 995 reg &= ~(SYSCON_ETCS_MASK | SYSCON_EPIT); 996 if (gmac->variant->support_rmii) 997 reg &= ~SYSCON_RMII_EN; 998 999 switch (plat->interface) { 1000 case PHY_INTERFACE_MODE_MII: 1001 /* default */ 1002 break; 1003 case PHY_INTERFACE_MODE_RGMII: 1004 case PHY_INTERFACE_MODE_RGMII_ID: 1005 case PHY_INTERFACE_MODE_RGMII_RXID: 1006 case PHY_INTERFACE_MODE_RGMII_TXID: 1007 reg |= SYSCON_EPIT | SYSCON_ETCS_INT_GMII; 1008 break; 1009 case PHY_INTERFACE_MODE_RMII: 1010 reg |= SYSCON_RMII_EN | SYSCON_ETCS_EXT_GMII; 1011 break; 1012 default: 1013 dev_err(dev, "Unsupported interface mode: %s", 1014 phy_modes(plat->interface)); 1015 return -EINVAL; 1016 } 1017 1018 regmap_field_write(gmac->regmap_field, reg); 1019 1020 return 0; 1021 } 1022 1023 static void sun8i_dwmac_unset_syscon(struct sunxi_priv_data *gmac) 1024 { 1025 u32 reg = gmac->variant->default_syscon_value; 1026 1027 regmap_field_write(gmac->regmap_field, reg); 1028 } 1029 1030 static void sun8i_dwmac_exit(struct platform_device *pdev, void *priv) 1031 { 1032 struct sunxi_priv_data *gmac = priv; 1033 1034 if (gmac->variant->soc_has_internal_phy) 1035 sun8i_dwmac_unpower_internal_phy(gmac); 1036 1037 if (gmac->regulator) 1038 regulator_disable(gmac->regulator); 1039 } 1040 1041 static void sun8i_dwmac_set_mac_loopback(void __iomem *ioaddr, bool enable) 1042 { 1043 u32 value = readl(ioaddr + EMAC_BASIC_CTL0); 1044 1045 if (enable) 1046 value |= EMAC_LOOPBACK; 1047 else 1048 value &= ~EMAC_LOOPBACK; 1049 1050 writel(value, ioaddr + EMAC_BASIC_CTL0); 1051 } 1052 1053 static const struct stmmac_ops sun8i_dwmac_ops = { 1054 .core_init = sun8i_dwmac_core_init, 1055 .set_mac = sun8i_dwmac_set_mac, 1056 .dump_regs = sun8i_dwmac_dump_mac_regs, 1057 .rx_ipc = sun8i_dwmac_rx_ipc_enable, 1058 .set_filter = sun8i_dwmac_set_filter, 1059 .flow_ctrl = sun8i_dwmac_flow_ctrl, 1060 .set_umac_addr = sun8i_dwmac_set_umac_addr, 1061 .get_umac_addr = sun8i_dwmac_get_umac_addr, 1062 .set_mac_loopback = sun8i_dwmac_set_mac_loopback, 1063 }; 1064 1065 static struct mac_device_info *sun8i_dwmac_setup(void *ppriv) 1066 { 1067 struct mac_device_info *mac; 1068 struct stmmac_priv *priv = ppriv; 1069 1070 mac = devm_kzalloc(priv->device, sizeof(*mac), GFP_KERNEL); 1071 if (!mac) 1072 return NULL; 1073 1074 mac->pcsr = priv->ioaddr; 1075 mac->mac = &sun8i_dwmac_ops; 1076 mac->dma = &sun8i_dwmac_dma_ops; 1077 1078 priv->dev->priv_flags |= IFF_UNICAST_FLT; 1079 1080 /* The loopback bit seems to be re-set when link change 1081 * Simply mask it each time 1082 * Speed 10/100/1000 are set in BIT(2)/BIT(3) 1083 */ 1084 mac->link.speed_mask = GENMASK(3, 2) | EMAC_LOOPBACK; 1085 mac->link.speed10 = EMAC_SPEED_10; 1086 mac->link.speed100 = EMAC_SPEED_100; 1087 mac->link.speed1000 = EMAC_SPEED_1000; 1088 mac->link.duplex = EMAC_DUPLEX_FULL; 1089 mac->mii.addr = EMAC_MDIO_CMD; 1090 mac->mii.data = EMAC_MDIO_DATA; 1091 mac->mii.reg_shift = 4; 1092 mac->mii.reg_mask = GENMASK(8, 4); 1093 mac->mii.addr_shift = 12; 1094 mac->mii.addr_mask = GENMASK(16, 12); 1095 mac->mii.clk_csr_shift = 20; 1096 mac->mii.clk_csr_mask = GENMASK(22, 20); 1097 mac->unicast_filter_entries = 8; 1098 1099 /* Synopsys Id is not available */ 1100 priv->synopsys_id = 0; 1101 1102 return mac; 1103 } 1104 1105 static struct regmap *sun8i_dwmac_get_syscon_from_dev(struct device_node *node) 1106 { 1107 struct device_node *syscon_node; 1108 struct platform_device *syscon_pdev; 1109 struct regmap *regmap = NULL; 1110 1111 syscon_node = of_parse_phandle(node, "syscon", 0); 1112 if (!syscon_node) 1113 return ERR_PTR(-ENODEV); 1114 1115 syscon_pdev = of_find_device_by_node(syscon_node); 1116 if (!syscon_pdev) { 1117 /* platform device might not be probed yet */ 1118 regmap = ERR_PTR(-EPROBE_DEFER); 1119 goto out_put_node; 1120 } 1121 1122 /* If no regmap is found then the other device driver is at fault */ 1123 regmap = dev_get_regmap(&syscon_pdev->dev, NULL); 1124 if (!regmap) 1125 regmap = ERR_PTR(-EINVAL); 1126 1127 platform_device_put(syscon_pdev); 1128 out_put_node: 1129 of_node_put(syscon_node); 1130 return regmap; 1131 } 1132 1133 static int sun8i_dwmac_probe(struct platform_device *pdev) 1134 { 1135 struct plat_stmmacenet_data *plat_dat; 1136 struct stmmac_resources stmmac_res; 1137 struct sunxi_priv_data *gmac; 1138 struct device *dev = &pdev->dev; 1139 phy_interface_t interface; 1140 int ret; 1141 struct stmmac_priv *priv; 1142 struct net_device *ndev; 1143 struct regmap *regmap; 1144 1145 ret = stmmac_get_platform_resources(pdev, &stmmac_res); 1146 if (ret) 1147 return ret; 1148 1149 gmac = devm_kzalloc(dev, sizeof(*gmac), GFP_KERNEL); 1150 if (!gmac) 1151 return -ENOMEM; 1152 1153 gmac->variant = of_device_get_match_data(&pdev->dev); 1154 if (!gmac->variant) { 1155 dev_err(&pdev->dev, "Missing dwmac-sun8i variant\n"); 1156 return -EINVAL; 1157 } 1158 1159 /* Optional regulator for PHY */ 1160 gmac->regulator = devm_regulator_get_optional(dev, "phy"); 1161 if (IS_ERR(gmac->regulator)) { 1162 if (PTR_ERR(gmac->regulator) == -EPROBE_DEFER) 1163 return -EPROBE_DEFER; 1164 dev_info(dev, "No regulator found\n"); 1165 gmac->regulator = NULL; 1166 } 1167 1168 /* The "GMAC clock control" register might be located in the 1169 * CCU address range (on the R40), or the system control address 1170 * range (on most other sun8i and later SoCs). 1171 * 1172 * The former controls most if not all clocks in the SoC. The 1173 * latter has an SoC identification register, and on some SoCs, 1174 * controls to map device specific SRAM to either the intended 1175 * peripheral, or the CPU address space. 1176 * 1177 * In either case, there should be a coordinated and restricted 1178 * method of accessing the register needed here. This is done by 1179 * having the device export a custom regmap, instead of a generic 1180 * syscon, which grants all access to all registers. 1181 * 1182 * To support old device trees, we fall back to using the syscon 1183 * interface if possible. 1184 */ 1185 regmap = sun8i_dwmac_get_syscon_from_dev(pdev->dev.of_node); 1186 if (IS_ERR(regmap)) 1187 regmap = syscon_regmap_lookup_by_phandle(pdev->dev.of_node, 1188 "syscon"); 1189 if (IS_ERR(regmap)) { 1190 ret = PTR_ERR(regmap); 1191 dev_err(&pdev->dev, "Unable to map syscon: %d\n", ret); 1192 return ret; 1193 } 1194 1195 gmac->regmap_field = devm_regmap_field_alloc(dev, regmap, 1196 *gmac->variant->syscon_field); 1197 if (IS_ERR(gmac->regmap_field)) { 1198 ret = PTR_ERR(gmac->regmap_field); 1199 dev_err(dev, "Unable to map syscon register: %d\n", ret); 1200 return ret; 1201 } 1202 1203 ret = of_get_phy_mode(dev->of_node, &interface); 1204 if (ret) 1205 return -EINVAL; 1206 1207 plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac); 1208 if (IS_ERR(plat_dat)) 1209 return PTR_ERR(plat_dat); 1210 1211 /* platform data specifying hardware features and callbacks. 1212 * hardware features were copied from Allwinner drivers. 1213 */ 1214 plat_dat->interface = interface; 1215 plat_dat->rx_coe = STMMAC_RX_COE_TYPE2; 1216 plat_dat->tx_coe = 1; 1217 plat_dat->has_sun8i = true; 1218 plat_dat->bsp_priv = gmac; 1219 plat_dat->init = sun8i_dwmac_init; 1220 plat_dat->exit = sun8i_dwmac_exit; 1221 plat_dat->setup = sun8i_dwmac_setup; 1222 plat_dat->tx_fifo_size = 4096; 1223 plat_dat->rx_fifo_size = 16384; 1224 1225 ret = sun8i_dwmac_set_syscon(&pdev->dev, plat_dat); 1226 if (ret) 1227 goto dwmac_deconfig; 1228 1229 ret = sun8i_dwmac_init(pdev, plat_dat->bsp_priv); 1230 if (ret) 1231 goto dwmac_syscon; 1232 1233 ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res); 1234 if (ret) 1235 goto dwmac_exit; 1236 1237 ndev = dev_get_drvdata(&pdev->dev); 1238 priv = netdev_priv(ndev); 1239 1240 /* the MAC is runtime suspended after stmmac_dvr_probe(), so we 1241 * need to ensure the MAC resume back before other operations such 1242 * as reset. 1243 */ 1244 pm_runtime_get_sync(&pdev->dev); 1245 1246 /* The mux must be registered after parent MDIO 1247 * so after stmmac_dvr_probe() 1248 */ 1249 if (gmac->variant->soc_has_internal_phy) { 1250 ret = get_ephy_nodes(priv); 1251 if (ret) 1252 goto dwmac_remove; 1253 ret = sun8i_dwmac_register_mdio_mux(priv); 1254 if (ret) { 1255 dev_err(&pdev->dev, "Failed to register mux\n"); 1256 goto dwmac_mux; 1257 } 1258 } else { 1259 ret = sun8i_dwmac_reset(priv); 1260 if (ret) 1261 goto dwmac_remove; 1262 } 1263 1264 pm_runtime_put(&pdev->dev); 1265 1266 return 0; 1267 1268 dwmac_mux: 1269 reset_control_put(gmac->rst_ephy); 1270 clk_put(gmac->ephy_clk); 1271 dwmac_remove: 1272 pm_runtime_put_noidle(&pdev->dev); 1273 stmmac_dvr_remove(&pdev->dev); 1274 dwmac_exit: 1275 sun8i_dwmac_exit(pdev, gmac); 1276 dwmac_syscon: 1277 sun8i_dwmac_unset_syscon(gmac); 1278 dwmac_deconfig: 1279 stmmac_remove_config_dt(pdev, plat_dat); 1280 1281 return ret; 1282 } 1283 1284 static int sun8i_dwmac_remove(struct platform_device *pdev) 1285 { 1286 struct net_device *ndev = platform_get_drvdata(pdev); 1287 struct stmmac_priv *priv = netdev_priv(ndev); 1288 struct sunxi_priv_data *gmac = priv->plat->bsp_priv; 1289 1290 if (gmac->variant->soc_has_internal_phy) { 1291 mdio_mux_uninit(gmac->mux_handle); 1292 sun8i_dwmac_unpower_internal_phy(gmac); 1293 reset_control_put(gmac->rst_ephy); 1294 clk_put(gmac->ephy_clk); 1295 } 1296 1297 stmmac_pltfr_remove(pdev); 1298 sun8i_dwmac_unset_syscon(gmac); 1299 1300 return 0; 1301 } 1302 1303 static void sun8i_dwmac_shutdown(struct platform_device *pdev) 1304 { 1305 struct net_device *ndev = platform_get_drvdata(pdev); 1306 struct stmmac_priv *priv = netdev_priv(ndev); 1307 struct sunxi_priv_data *gmac = priv->plat->bsp_priv; 1308 1309 sun8i_dwmac_exit(pdev, gmac); 1310 } 1311 1312 static const struct of_device_id sun8i_dwmac_match[] = { 1313 { .compatible = "allwinner,sun8i-h3-emac", 1314 .data = &emac_variant_h3 }, 1315 { .compatible = "allwinner,sun8i-v3s-emac", 1316 .data = &emac_variant_v3s }, 1317 { .compatible = "allwinner,sun8i-a83t-emac", 1318 .data = &emac_variant_a83t }, 1319 { .compatible = "allwinner,sun8i-r40-gmac", 1320 .data = &emac_variant_r40 }, 1321 { .compatible = "allwinner,sun50i-a64-emac", 1322 .data = &emac_variant_a64 }, 1323 { .compatible = "allwinner,sun50i-h6-emac", 1324 .data = &emac_variant_h6 }, 1325 { } 1326 }; 1327 MODULE_DEVICE_TABLE(of, sun8i_dwmac_match); 1328 1329 static struct platform_driver sun8i_dwmac_driver = { 1330 .probe = sun8i_dwmac_probe, 1331 .remove = sun8i_dwmac_remove, 1332 .shutdown = sun8i_dwmac_shutdown, 1333 .driver = { 1334 .name = "dwmac-sun8i", 1335 .pm = &stmmac_pltfr_pm_ops, 1336 .of_match_table = sun8i_dwmac_match, 1337 }, 1338 }; 1339 module_platform_driver(sun8i_dwmac_driver); 1340 1341 MODULE_AUTHOR("Corentin Labbe <clabbe.montjoie@gmail.com>"); 1342 MODULE_DESCRIPTION("Allwinner sun8i DWMAC specific glue layer"); 1343 MODULE_LICENSE("GPL"); 1344