1config STMMAC_ETH
2	tristate "STMicroelectronics 10/100/1000 Ethernet driver"
3	depends on HAS_IOMEM && HAS_DMA
4	select MII
5	select PHYLIB
6	select CRC32
7	select PTP_1588_CLOCK
8	select RESET_CONTROLLER
9	---help---
10	  This is the driver for the Ethernet IPs are built around a
11	  Synopsys IP Core and only tested on the STMicroelectronics
12	  platforms.
13
14if STMMAC_ETH
15
16config STMMAC_PLATFORM
17	tristate "STMMAC Platform bus support"
18	depends on STMMAC_ETH
19	select MFD_SYSCON
20	default y
21	---help---
22	  This selects the platform specific bus support for the stmmac driver.
23	  This is the driver used on several SoCs:
24	  STi, Allwinner, Amlogic Meson, Altera SOCFPGA.
25
26	  If you have a controller with this interface, say Y or M here.
27
28	  If unsure, say N.
29
30if STMMAC_PLATFORM
31
32config DWMAC_GENERIC
33	tristate "Generic driver for DWMAC"
34	default STMMAC_PLATFORM
35	---help---
36	  Generic DWMAC driver for platforms that don't require any
37	  platform specific code to function or is using platform
38	  data for setup.
39
40config DWMAC_IPQ806X
41	tristate "QCA IPQ806x DWMAC support"
42	default ARCH_QCOM
43	depends on OF
44	select MFD_SYSCON
45	help
46	  Support for QCA IPQ806X DWMAC Ethernet.
47
48	  This selects the IPQ806x SoC glue layer support for the stmmac
49	  device driver. This driver does not use any of the hardware
50	  acceleration features available on this SoC. Network devices
51	  will behave like standard non-accelerated ethernet interfaces.
52
53config DWMAC_LPC18XX
54	tristate "NXP LPC18xx/43xx DWMAC support"
55	default ARCH_LPC18XX
56	depends on OF
57	select MFD_SYSCON
58	---help---
59	  Support for NXP LPC18xx/43xx DWMAC Ethernet.
60
61config DWMAC_MESON
62	tristate "Amlogic Meson dwmac support"
63	default ARCH_MESON
64	depends on OF
65	help
66	  Support for Ethernet controller on Amlogic Meson SoCs.
67
68	  This selects the Amlogic Meson SoC glue layer support for
69	  the stmmac device driver. This driver is used for Meson6 and
70	  Meson8 SoCs.
71
72config DWMAC_ROCKCHIP
73	tristate "Rockchip dwmac support"
74	default ARCH_ROCKCHIP
75	depends on OF
76	select MFD_SYSCON
77	help
78	  Support for Ethernet controller on Rockchip RK3288 SoC.
79
80	  This selects the Rockchip RK3288 SoC glue layer support for
81	  the stmmac device driver.
82
83config DWMAC_SOCFPGA
84	tristate "SOCFPGA dwmac support"
85	default ARCH_SOCFPGA
86	depends on OF
87	select MFD_SYSCON
88	help
89	  Support for ethernet controller on Altera SOCFPGA
90
91	  This selects the Altera SOCFPGA SoC glue layer support
92	  for the stmmac device driver. This driver is used for
93	  arria5 and cyclone5 FPGA SoCs.
94
95config DWMAC_STI
96	tristate "STi GMAC support"
97	default ARCH_STI
98	depends on OF
99	select MFD_SYSCON
100	---help---
101	  Support for ethernet controller on STi SOCs.
102
103	  This selects STi SoC glue layer support for the stmmac
104	  device driver. This driver is used on for the STi series
105	  SOCs GMAC ethernet controller.
106
107config DWMAC_SUNXI
108	tristate "Allwinner GMAC support"
109	default ARCH_SUNXI
110	depends on OF
111	---help---
112	  Support for Allwinner A20/A31 GMAC ethernet controllers.
113
114	  This selects Allwinner SoC glue layer support for the
115	  stmmac device driver. This driver is used for A20/A31
116	  GMAC ethernet controller.
117endif
118
119config STMMAC_PCI
120	tristate "STMMAC PCI bus support"
121	depends on STMMAC_ETH && PCI
122	---help---
123	  This is to select the Synopsys DWMAC available on PCI devices,
124	  if you have a controller with this interface, say Y or M here.
125
126	  This PCI support is tested on XLINX XC2V3000 FF1152AMT0221
127	  D1215994A VIRTEX FPGA board.
128
129	  If unsure, say N.
130endif
131