1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /*************************************************************************** 3 * 4 * Copyright (C) 2004-2008 SMSC 5 * Copyright (C) 2005-2008 ARM 6 * 7 *************************************************************************** 8 * Rewritten, heavily based on smsc911x simple driver by SMSC. 9 * Partly uses io macros from smc91x.c by Nicolas Pitre 10 * 11 * Supported devices: 12 * LAN9115, LAN9116, LAN9117, LAN9118 13 * LAN9215, LAN9216, LAN9217, LAN9218 14 * LAN9210, LAN9211 15 * LAN9220, LAN9221 16 * LAN89218,LAN9250 17 */ 18 19 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt 20 21 #include <linux/crc32.h> 22 #include <linux/clk.h> 23 #include <linux/delay.h> 24 #include <linux/errno.h> 25 #include <linux/etherdevice.h> 26 #include <linux/ethtool.h> 27 #include <linux/init.h> 28 #include <linux/interrupt.h> 29 #include <linux/ioport.h> 30 #include <linux/kernel.h> 31 #include <linux/module.h> 32 #include <linux/netdevice.h> 33 #include <linux/platform_device.h> 34 #include <linux/regulator/consumer.h> 35 #include <linux/sched.h> 36 #include <linux/timer.h> 37 #include <linux/bug.h> 38 #include <linux/bitops.h> 39 #include <linux/irq.h> 40 #include <linux/io.h> 41 #include <linux/swab.h> 42 #include <linux/phy.h> 43 #include <linux/smsc911x.h> 44 #include <linux/device.h> 45 #include <linux/of.h> 46 #include <linux/of_gpio.h> 47 #include <linux/of_net.h> 48 #include <linux/acpi.h> 49 #include <linux/pm_runtime.h> 50 #include <linux/property.h> 51 #include <linux/gpio/consumer.h> 52 53 #include "smsc911x.h" 54 55 #define SMSC_CHIPNAME "smsc911x" 56 #define SMSC_MDIONAME "smsc911x-mdio" 57 #define SMSC_DRV_VERSION "2008-10-21" 58 59 MODULE_LICENSE("GPL"); 60 MODULE_VERSION(SMSC_DRV_VERSION); 61 MODULE_ALIAS("platform:smsc911x"); 62 63 #if USE_DEBUG > 0 64 static int debug = 16; 65 #else 66 static int debug = 3; 67 #endif 68 69 module_param(debug, int, 0); 70 MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)"); 71 72 struct smsc911x_data; 73 74 struct smsc911x_ops { 75 u32 (*reg_read)(struct smsc911x_data *pdata, u32 reg); 76 void (*reg_write)(struct smsc911x_data *pdata, u32 reg, u32 val); 77 void (*rx_readfifo)(struct smsc911x_data *pdata, 78 unsigned int *buf, unsigned int wordcount); 79 void (*tx_writefifo)(struct smsc911x_data *pdata, 80 unsigned int *buf, unsigned int wordcount); 81 }; 82 83 #define SMSC911X_NUM_SUPPLIES 2 84 85 struct smsc911x_data { 86 void __iomem *ioaddr; 87 88 unsigned int idrev; 89 90 /* used to decide which workarounds apply */ 91 unsigned int generation; 92 93 /* device configuration (copied from platform_data during probe) */ 94 struct smsc911x_platform_config config; 95 96 /* This needs to be acquired before calling any of below: 97 * smsc911x_mac_read(), smsc911x_mac_write() 98 */ 99 spinlock_t mac_lock; 100 101 /* spinlock to ensure register accesses are serialised */ 102 spinlock_t dev_lock; 103 104 struct mii_bus *mii_bus; 105 unsigned int using_extphy; 106 int last_duplex; 107 int last_carrier; 108 109 u32 msg_enable; 110 unsigned int gpio_setting; 111 unsigned int gpio_orig_setting; 112 struct net_device *dev; 113 struct napi_struct napi; 114 115 unsigned int software_irq_signal; 116 117 #ifdef USE_PHY_WORK_AROUND 118 #define MIN_PACKET_SIZE (64) 119 char loopback_tx_pkt[MIN_PACKET_SIZE]; 120 char loopback_rx_pkt[MIN_PACKET_SIZE]; 121 unsigned int resetcount; 122 #endif 123 124 /* Members for Multicast filter workaround */ 125 unsigned int multicast_update_pending; 126 unsigned int set_bits_mask; 127 unsigned int clear_bits_mask; 128 unsigned int hashhi; 129 unsigned int hashlo; 130 131 /* register access functions */ 132 const struct smsc911x_ops *ops; 133 134 /* regulators */ 135 struct regulator_bulk_data supplies[SMSC911X_NUM_SUPPLIES]; 136 137 /* Reset GPIO */ 138 struct gpio_desc *reset_gpiod; 139 140 /* clock */ 141 struct clk *clk; 142 }; 143 144 /* Easy access to information */ 145 #define __smsc_shift(pdata, reg) ((reg) << ((pdata)->config.shift)) 146 147 static inline u32 __smsc911x_reg_read(struct smsc911x_data *pdata, u32 reg) 148 { 149 if (pdata->config.flags & SMSC911X_USE_32BIT) 150 return readl(pdata->ioaddr + reg); 151 152 if (pdata->config.flags & SMSC911X_USE_16BIT) 153 return ((readw(pdata->ioaddr + reg) & 0xFFFF) | 154 ((readw(pdata->ioaddr + reg + 2) & 0xFFFF) << 16)); 155 156 BUG(); 157 return 0; 158 } 159 160 static inline u32 161 __smsc911x_reg_read_shift(struct smsc911x_data *pdata, u32 reg) 162 { 163 if (pdata->config.flags & SMSC911X_USE_32BIT) 164 return readl(pdata->ioaddr + __smsc_shift(pdata, reg)); 165 166 if (pdata->config.flags & SMSC911X_USE_16BIT) 167 return (readw(pdata->ioaddr + 168 __smsc_shift(pdata, reg)) & 0xFFFF) | 169 ((readw(pdata->ioaddr + 170 __smsc_shift(pdata, reg + 2)) & 0xFFFF) << 16); 171 172 BUG(); 173 return 0; 174 } 175 176 static inline u32 smsc911x_reg_read(struct smsc911x_data *pdata, u32 reg) 177 { 178 u32 data; 179 unsigned long flags; 180 181 spin_lock_irqsave(&pdata->dev_lock, flags); 182 data = pdata->ops->reg_read(pdata, reg); 183 spin_unlock_irqrestore(&pdata->dev_lock, flags); 184 185 return data; 186 } 187 188 static inline void __smsc911x_reg_write(struct smsc911x_data *pdata, u32 reg, 189 u32 val) 190 { 191 if (pdata->config.flags & SMSC911X_USE_32BIT) { 192 writel(val, pdata->ioaddr + reg); 193 return; 194 } 195 196 if (pdata->config.flags & SMSC911X_USE_16BIT) { 197 writew(val & 0xFFFF, pdata->ioaddr + reg); 198 writew((val >> 16) & 0xFFFF, pdata->ioaddr + reg + 2); 199 return; 200 } 201 202 BUG(); 203 } 204 205 static inline void 206 __smsc911x_reg_write_shift(struct smsc911x_data *pdata, u32 reg, u32 val) 207 { 208 if (pdata->config.flags & SMSC911X_USE_32BIT) { 209 writel(val, pdata->ioaddr + __smsc_shift(pdata, reg)); 210 return; 211 } 212 213 if (pdata->config.flags & SMSC911X_USE_16BIT) { 214 writew(val & 0xFFFF, 215 pdata->ioaddr + __smsc_shift(pdata, reg)); 216 writew((val >> 16) & 0xFFFF, 217 pdata->ioaddr + __smsc_shift(pdata, reg + 2)); 218 return; 219 } 220 221 BUG(); 222 } 223 224 static inline void smsc911x_reg_write(struct smsc911x_data *pdata, u32 reg, 225 u32 val) 226 { 227 unsigned long flags; 228 229 spin_lock_irqsave(&pdata->dev_lock, flags); 230 pdata->ops->reg_write(pdata, reg, val); 231 spin_unlock_irqrestore(&pdata->dev_lock, flags); 232 } 233 234 /* Writes a packet to the TX_DATA_FIFO */ 235 static inline void 236 smsc911x_tx_writefifo(struct smsc911x_data *pdata, unsigned int *buf, 237 unsigned int wordcount) 238 { 239 unsigned long flags; 240 241 spin_lock_irqsave(&pdata->dev_lock, flags); 242 243 if (pdata->config.flags & SMSC911X_SWAP_FIFO) { 244 while (wordcount--) 245 __smsc911x_reg_write(pdata, TX_DATA_FIFO, 246 swab32(*buf++)); 247 goto out; 248 } 249 250 if (pdata->config.flags & SMSC911X_USE_32BIT) { 251 iowrite32_rep(pdata->ioaddr + TX_DATA_FIFO, buf, wordcount); 252 goto out; 253 } 254 255 if (pdata->config.flags & SMSC911X_USE_16BIT) { 256 while (wordcount--) 257 __smsc911x_reg_write(pdata, TX_DATA_FIFO, *buf++); 258 goto out; 259 } 260 261 BUG(); 262 out: 263 spin_unlock_irqrestore(&pdata->dev_lock, flags); 264 } 265 266 /* Writes a packet to the TX_DATA_FIFO - shifted version */ 267 static inline void 268 smsc911x_tx_writefifo_shift(struct smsc911x_data *pdata, unsigned int *buf, 269 unsigned int wordcount) 270 { 271 unsigned long flags; 272 273 spin_lock_irqsave(&pdata->dev_lock, flags); 274 275 if (pdata->config.flags & SMSC911X_SWAP_FIFO) { 276 while (wordcount--) 277 __smsc911x_reg_write_shift(pdata, TX_DATA_FIFO, 278 swab32(*buf++)); 279 goto out; 280 } 281 282 if (pdata->config.flags & SMSC911X_USE_32BIT) { 283 iowrite32_rep(pdata->ioaddr + __smsc_shift(pdata, 284 TX_DATA_FIFO), buf, wordcount); 285 goto out; 286 } 287 288 if (pdata->config.flags & SMSC911X_USE_16BIT) { 289 while (wordcount--) 290 __smsc911x_reg_write_shift(pdata, 291 TX_DATA_FIFO, *buf++); 292 goto out; 293 } 294 295 BUG(); 296 out: 297 spin_unlock_irqrestore(&pdata->dev_lock, flags); 298 } 299 300 /* Reads a packet out of the RX_DATA_FIFO */ 301 static inline void 302 smsc911x_rx_readfifo(struct smsc911x_data *pdata, unsigned int *buf, 303 unsigned int wordcount) 304 { 305 unsigned long flags; 306 307 spin_lock_irqsave(&pdata->dev_lock, flags); 308 309 if (pdata->config.flags & SMSC911X_SWAP_FIFO) { 310 while (wordcount--) 311 *buf++ = swab32(__smsc911x_reg_read(pdata, 312 RX_DATA_FIFO)); 313 goto out; 314 } 315 316 if (pdata->config.flags & SMSC911X_USE_32BIT) { 317 ioread32_rep(pdata->ioaddr + RX_DATA_FIFO, buf, wordcount); 318 goto out; 319 } 320 321 if (pdata->config.flags & SMSC911X_USE_16BIT) { 322 while (wordcount--) 323 *buf++ = __smsc911x_reg_read(pdata, RX_DATA_FIFO); 324 goto out; 325 } 326 327 BUG(); 328 out: 329 spin_unlock_irqrestore(&pdata->dev_lock, flags); 330 } 331 332 /* Reads a packet out of the RX_DATA_FIFO - shifted version */ 333 static inline void 334 smsc911x_rx_readfifo_shift(struct smsc911x_data *pdata, unsigned int *buf, 335 unsigned int wordcount) 336 { 337 unsigned long flags; 338 339 spin_lock_irqsave(&pdata->dev_lock, flags); 340 341 if (pdata->config.flags & SMSC911X_SWAP_FIFO) { 342 while (wordcount--) 343 *buf++ = swab32(__smsc911x_reg_read_shift(pdata, 344 RX_DATA_FIFO)); 345 goto out; 346 } 347 348 if (pdata->config.flags & SMSC911X_USE_32BIT) { 349 ioread32_rep(pdata->ioaddr + __smsc_shift(pdata, 350 RX_DATA_FIFO), buf, wordcount); 351 goto out; 352 } 353 354 if (pdata->config.flags & SMSC911X_USE_16BIT) { 355 while (wordcount--) 356 *buf++ = __smsc911x_reg_read_shift(pdata, 357 RX_DATA_FIFO); 358 goto out; 359 } 360 361 BUG(); 362 out: 363 spin_unlock_irqrestore(&pdata->dev_lock, flags); 364 } 365 366 /* 367 * enable regulator and clock resources. 368 */ 369 static int smsc911x_enable_resources(struct platform_device *pdev) 370 { 371 struct net_device *ndev = platform_get_drvdata(pdev); 372 struct smsc911x_data *pdata = netdev_priv(ndev); 373 int ret = 0; 374 375 ret = regulator_bulk_enable(ARRAY_SIZE(pdata->supplies), 376 pdata->supplies); 377 if (ret) 378 netdev_err(ndev, "failed to enable regulators %d\n", 379 ret); 380 381 if (!IS_ERR(pdata->clk)) { 382 ret = clk_prepare_enable(pdata->clk); 383 if (ret < 0) 384 netdev_err(ndev, "failed to enable clock %d\n", ret); 385 } 386 387 return ret; 388 } 389 390 /* 391 * disable resources, currently just regulators. 392 */ 393 static int smsc911x_disable_resources(struct platform_device *pdev) 394 { 395 struct net_device *ndev = platform_get_drvdata(pdev); 396 struct smsc911x_data *pdata = netdev_priv(ndev); 397 int ret = 0; 398 399 ret = regulator_bulk_disable(ARRAY_SIZE(pdata->supplies), 400 pdata->supplies); 401 402 if (!IS_ERR(pdata->clk)) 403 clk_disable_unprepare(pdata->clk); 404 405 return ret; 406 } 407 408 /* 409 * Request resources, currently just regulators. 410 * 411 * The SMSC911x has two power pins: vddvario and vdd33a, in designs where 412 * these are not always-on we need to request regulators to be turned on 413 * before we can try to access the device registers. 414 */ 415 static int smsc911x_request_resources(struct platform_device *pdev) 416 { 417 struct net_device *ndev = platform_get_drvdata(pdev); 418 struct smsc911x_data *pdata = netdev_priv(ndev); 419 int ret = 0; 420 421 /* Request regulators */ 422 pdata->supplies[0].supply = "vdd33a"; 423 pdata->supplies[1].supply = "vddvario"; 424 ret = regulator_bulk_get(&pdev->dev, 425 ARRAY_SIZE(pdata->supplies), 426 pdata->supplies); 427 if (ret) { 428 /* 429 * Retry on deferrals, else just report the error 430 * and try to continue. 431 */ 432 if (ret == -EPROBE_DEFER) 433 return ret; 434 netdev_err(ndev, "couldn't get regulators %d\n", 435 ret); 436 } 437 438 /* Request optional RESET GPIO */ 439 pdata->reset_gpiod = devm_gpiod_get_optional(&pdev->dev, 440 "reset", 441 GPIOD_OUT_LOW); 442 443 /* Request clock */ 444 pdata->clk = clk_get(&pdev->dev, NULL); 445 if (IS_ERR(pdata->clk)) 446 dev_dbg(&pdev->dev, "couldn't get clock %li\n", 447 PTR_ERR(pdata->clk)); 448 449 return ret; 450 } 451 452 /* 453 * Free resources, currently just regulators. 454 * 455 */ 456 static void smsc911x_free_resources(struct platform_device *pdev) 457 { 458 struct net_device *ndev = platform_get_drvdata(pdev); 459 struct smsc911x_data *pdata = netdev_priv(ndev); 460 461 /* Free regulators */ 462 regulator_bulk_free(ARRAY_SIZE(pdata->supplies), 463 pdata->supplies); 464 465 /* Free clock */ 466 if (!IS_ERR(pdata->clk)) { 467 clk_put(pdata->clk); 468 pdata->clk = NULL; 469 } 470 } 471 472 /* waits for MAC not busy, with timeout. Only called by smsc911x_mac_read 473 * and smsc911x_mac_write, so assumes mac_lock is held */ 474 static int smsc911x_mac_complete(struct smsc911x_data *pdata) 475 { 476 int i; 477 u32 val; 478 479 SMSC_ASSERT_MAC_LOCK(pdata); 480 481 for (i = 0; i < 40; i++) { 482 val = smsc911x_reg_read(pdata, MAC_CSR_CMD); 483 if (!(val & MAC_CSR_CMD_CSR_BUSY_)) 484 return 0; 485 } 486 SMSC_WARN(pdata, hw, "Timed out waiting for MAC not BUSY. " 487 "MAC_CSR_CMD: 0x%08X", val); 488 return -EIO; 489 } 490 491 /* Fetches a MAC register value. Assumes mac_lock is acquired */ 492 static u32 smsc911x_mac_read(struct smsc911x_data *pdata, unsigned int offset) 493 { 494 unsigned int temp; 495 496 SMSC_ASSERT_MAC_LOCK(pdata); 497 498 temp = smsc911x_reg_read(pdata, MAC_CSR_CMD); 499 if (unlikely(temp & MAC_CSR_CMD_CSR_BUSY_)) { 500 SMSC_WARN(pdata, hw, "MAC busy at entry"); 501 return 0xFFFFFFFF; 502 } 503 504 /* Send the MAC cmd */ 505 smsc911x_reg_write(pdata, MAC_CSR_CMD, ((offset & 0xFF) | 506 MAC_CSR_CMD_CSR_BUSY_ | MAC_CSR_CMD_R_NOT_W_)); 507 508 /* Workaround for hardware read-after-write restriction */ 509 temp = smsc911x_reg_read(pdata, BYTE_TEST); 510 511 /* Wait for the read to complete */ 512 if (likely(smsc911x_mac_complete(pdata) == 0)) 513 return smsc911x_reg_read(pdata, MAC_CSR_DATA); 514 515 SMSC_WARN(pdata, hw, "MAC busy after read"); 516 return 0xFFFFFFFF; 517 } 518 519 /* Set a mac register, mac_lock must be acquired before calling */ 520 static void smsc911x_mac_write(struct smsc911x_data *pdata, 521 unsigned int offset, u32 val) 522 { 523 unsigned int temp; 524 525 SMSC_ASSERT_MAC_LOCK(pdata); 526 527 temp = smsc911x_reg_read(pdata, MAC_CSR_CMD); 528 if (unlikely(temp & MAC_CSR_CMD_CSR_BUSY_)) { 529 SMSC_WARN(pdata, hw, 530 "smsc911x_mac_write failed, MAC busy at entry"); 531 return; 532 } 533 534 /* Send data to write */ 535 smsc911x_reg_write(pdata, MAC_CSR_DATA, val); 536 537 /* Write the actual data */ 538 smsc911x_reg_write(pdata, MAC_CSR_CMD, ((offset & 0xFF) | 539 MAC_CSR_CMD_CSR_BUSY_)); 540 541 /* Workaround for hardware read-after-write restriction */ 542 temp = smsc911x_reg_read(pdata, BYTE_TEST); 543 544 /* Wait for the write to complete */ 545 if (likely(smsc911x_mac_complete(pdata) == 0)) 546 return; 547 548 SMSC_WARN(pdata, hw, "smsc911x_mac_write failed, MAC busy after write"); 549 } 550 551 /* Get a phy register */ 552 static int smsc911x_mii_read(struct mii_bus *bus, int phyaddr, int regidx) 553 { 554 struct smsc911x_data *pdata = bus->priv; 555 unsigned long flags; 556 unsigned int addr; 557 int i, reg; 558 559 pm_runtime_get_sync(bus->parent); 560 spin_lock_irqsave(&pdata->mac_lock, flags); 561 562 /* Confirm MII not busy */ 563 if (unlikely(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) { 564 SMSC_WARN(pdata, hw, "MII is busy in smsc911x_mii_read???"); 565 reg = -EIO; 566 goto out; 567 } 568 569 /* Set the address, index & direction (read from PHY) */ 570 addr = ((phyaddr & 0x1F) << 11) | ((regidx & 0x1F) << 6); 571 smsc911x_mac_write(pdata, MII_ACC, addr); 572 573 /* Wait for read to complete w/ timeout */ 574 for (i = 0; i < 100; i++) 575 if (!(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) { 576 reg = smsc911x_mac_read(pdata, MII_DATA); 577 goto out; 578 } 579 580 SMSC_WARN(pdata, hw, "Timed out waiting for MII read to finish"); 581 reg = -EIO; 582 583 out: 584 spin_unlock_irqrestore(&pdata->mac_lock, flags); 585 pm_runtime_put(bus->parent); 586 return reg; 587 } 588 589 /* Set a phy register */ 590 static int smsc911x_mii_write(struct mii_bus *bus, int phyaddr, int regidx, 591 u16 val) 592 { 593 struct smsc911x_data *pdata = bus->priv; 594 unsigned long flags; 595 unsigned int addr; 596 int i, reg; 597 598 pm_runtime_get_sync(bus->parent); 599 spin_lock_irqsave(&pdata->mac_lock, flags); 600 601 /* Confirm MII not busy */ 602 if (unlikely(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) { 603 SMSC_WARN(pdata, hw, "MII is busy in smsc911x_mii_write???"); 604 reg = -EIO; 605 goto out; 606 } 607 608 /* Put the data to write in the MAC */ 609 smsc911x_mac_write(pdata, MII_DATA, val); 610 611 /* Set the address, index & direction (write to PHY) */ 612 addr = ((phyaddr & 0x1F) << 11) | ((regidx & 0x1F) << 6) | 613 MII_ACC_MII_WRITE_; 614 smsc911x_mac_write(pdata, MII_ACC, addr); 615 616 /* Wait for write to complete w/ timeout */ 617 for (i = 0; i < 100; i++) 618 if (!(smsc911x_mac_read(pdata, MII_ACC) & MII_ACC_MII_BUSY_)) { 619 reg = 0; 620 goto out; 621 } 622 623 SMSC_WARN(pdata, hw, "Timed out waiting for MII write to finish"); 624 reg = -EIO; 625 626 out: 627 spin_unlock_irqrestore(&pdata->mac_lock, flags); 628 pm_runtime_put(bus->parent); 629 return reg; 630 } 631 632 /* Switch to external phy. Assumes tx and rx are stopped. */ 633 static void smsc911x_phy_enable_external(struct smsc911x_data *pdata) 634 { 635 unsigned int hwcfg = smsc911x_reg_read(pdata, HW_CFG); 636 637 /* Disable phy clocks to the MAC */ 638 hwcfg &= (~HW_CFG_PHY_CLK_SEL_); 639 hwcfg |= HW_CFG_PHY_CLK_SEL_CLK_DIS_; 640 smsc911x_reg_write(pdata, HW_CFG, hwcfg); 641 udelay(10); /* Enough time for clocks to stop */ 642 643 /* Switch to external phy */ 644 hwcfg |= HW_CFG_EXT_PHY_EN_; 645 smsc911x_reg_write(pdata, HW_CFG, hwcfg); 646 647 /* Enable phy clocks to the MAC */ 648 hwcfg &= (~HW_CFG_PHY_CLK_SEL_); 649 hwcfg |= HW_CFG_PHY_CLK_SEL_EXT_PHY_; 650 smsc911x_reg_write(pdata, HW_CFG, hwcfg); 651 udelay(10); /* Enough time for clocks to restart */ 652 653 hwcfg |= HW_CFG_SMI_SEL_; 654 smsc911x_reg_write(pdata, HW_CFG, hwcfg); 655 } 656 657 /* Autodetects and enables external phy if present on supported chips. 658 * autodetection can be overridden by specifying SMSC911X_FORCE_INTERNAL_PHY 659 * or SMSC911X_FORCE_EXTERNAL_PHY in the platform_data flags. */ 660 static void smsc911x_phy_initialise_external(struct smsc911x_data *pdata) 661 { 662 unsigned int hwcfg = smsc911x_reg_read(pdata, HW_CFG); 663 664 if (pdata->config.flags & SMSC911X_FORCE_INTERNAL_PHY) { 665 SMSC_TRACE(pdata, hw, "Forcing internal PHY"); 666 pdata->using_extphy = 0; 667 } else if (pdata->config.flags & SMSC911X_FORCE_EXTERNAL_PHY) { 668 SMSC_TRACE(pdata, hw, "Forcing external PHY"); 669 smsc911x_phy_enable_external(pdata); 670 pdata->using_extphy = 1; 671 } else if (hwcfg & HW_CFG_EXT_PHY_DET_) { 672 SMSC_TRACE(pdata, hw, 673 "HW_CFG EXT_PHY_DET set, using external PHY"); 674 smsc911x_phy_enable_external(pdata); 675 pdata->using_extphy = 1; 676 } else { 677 SMSC_TRACE(pdata, hw, 678 "HW_CFG EXT_PHY_DET clear, using internal PHY"); 679 pdata->using_extphy = 0; 680 } 681 } 682 683 /* Fetches a tx status out of the status fifo */ 684 static unsigned int smsc911x_tx_get_txstatus(struct smsc911x_data *pdata) 685 { 686 unsigned int result = 687 smsc911x_reg_read(pdata, TX_FIFO_INF) & TX_FIFO_INF_TSUSED_; 688 689 if (result != 0) 690 result = smsc911x_reg_read(pdata, TX_STATUS_FIFO); 691 692 return result; 693 } 694 695 /* Fetches the next rx status */ 696 static unsigned int smsc911x_rx_get_rxstatus(struct smsc911x_data *pdata) 697 { 698 unsigned int result = 699 smsc911x_reg_read(pdata, RX_FIFO_INF) & RX_FIFO_INF_RXSUSED_; 700 701 if (result != 0) 702 result = smsc911x_reg_read(pdata, RX_STATUS_FIFO); 703 704 return result; 705 } 706 707 #ifdef USE_PHY_WORK_AROUND 708 static int smsc911x_phy_check_loopbackpkt(struct smsc911x_data *pdata) 709 { 710 unsigned int tries; 711 u32 wrsz; 712 u32 rdsz; 713 ulong bufp; 714 715 for (tries = 0; tries < 10; tries++) { 716 unsigned int txcmd_a; 717 unsigned int txcmd_b; 718 unsigned int status; 719 unsigned int pktlength; 720 unsigned int i; 721 722 /* Zero-out rx packet memory */ 723 memset(pdata->loopback_rx_pkt, 0, MIN_PACKET_SIZE); 724 725 /* Write tx packet to 118 */ 726 txcmd_a = (u32)((ulong)pdata->loopback_tx_pkt & 0x03) << 16; 727 txcmd_a |= TX_CMD_A_FIRST_SEG_ | TX_CMD_A_LAST_SEG_; 728 txcmd_a |= MIN_PACKET_SIZE; 729 730 txcmd_b = MIN_PACKET_SIZE << 16 | MIN_PACKET_SIZE; 731 732 smsc911x_reg_write(pdata, TX_DATA_FIFO, txcmd_a); 733 smsc911x_reg_write(pdata, TX_DATA_FIFO, txcmd_b); 734 735 bufp = (ulong)pdata->loopback_tx_pkt & (~0x3); 736 wrsz = MIN_PACKET_SIZE + 3; 737 wrsz += (u32)((ulong)pdata->loopback_tx_pkt & 0x3); 738 wrsz >>= 2; 739 740 pdata->ops->tx_writefifo(pdata, (unsigned int *)bufp, wrsz); 741 742 /* Wait till transmit is done */ 743 i = 60; 744 do { 745 udelay(5); 746 status = smsc911x_tx_get_txstatus(pdata); 747 } while ((i--) && (!status)); 748 749 if (!status) { 750 SMSC_WARN(pdata, hw, 751 "Failed to transmit during loopback test"); 752 continue; 753 } 754 if (status & TX_STS_ES_) { 755 SMSC_WARN(pdata, hw, 756 "Transmit encountered errors during loopback test"); 757 continue; 758 } 759 760 /* Wait till receive is done */ 761 i = 60; 762 do { 763 udelay(5); 764 status = smsc911x_rx_get_rxstatus(pdata); 765 } while ((i--) && (!status)); 766 767 if (!status) { 768 SMSC_WARN(pdata, hw, 769 "Failed to receive during loopback test"); 770 continue; 771 } 772 if (status & RX_STS_ES_) { 773 SMSC_WARN(pdata, hw, 774 "Receive encountered errors during loopback test"); 775 continue; 776 } 777 778 pktlength = ((status & 0x3FFF0000UL) >> 16); 779 bufp = (ulong)pdata->loopback_rx_pkt; 780 rdsz = pktlength + 3; 781 rdsz += (u32)((ulong)pdata->loopback_rx_pkt & 0x3); 782 rdsz >>= 2; 783 784 pdata->ops->rx_readfifo(pdata, (unsigned int *)bufp, rdsz); 785 786 if (pktlength != (MIN_PACKET_SIZE + 4)) { 787 SMSC_WARN(pdata, hw, "Unexpected packet size " 788 "during loop back test, size=%d, will retry", 789 pktlength); 790 } else { 791 unsigned int j; 792 int mismatch = 0; 793 for (j = 0; j < MIN_PACKET_SIZE; j++) { 794 if (pdata->loopback_tx_pkt[j] 795 != pdata->loopback_rx_pkt[j]) { 796 mismatch = 1; 797 break; 798 } 799 } 800 if (!mismatch) { 801 SMSC_TRACE(pdata, hw, "Successfully verified " 802 "loopback packet"); 803 return 0; 804 } else { 805 SMSC_WARN(pdata, hw, "Data mismatch " 806 "during loop back test, will retry"); 807 } 808 } 809 } 810 811 return -EIO; 812 } 813 814 static int smsc911x_phy_reset(struct smsc911x_data *pdata) 815 { 816 unsigned int temp; 817 unsigned int i = 100000; 818 819 temp = smsc911x_reg_read(pdata, PMT_CTRL); 820 smsc911x_reg_write(pdata, PMT_CTRL, temp | PMT_CTRL_PHY_RST_); 821 do { 822 msleep(1); 823 temp = smsc911x_reg_read(pdata, PMT_CTRL); 824 } while ((i--) && (temp & PMT_CTRL_PHY_RST_)); 825 826 if (unlikely(temp & PMT_CTRL_PHY_RST_)) { 827 SMSC_WARN(pdata, hw, "PHY reset failed to complete"); 828 return -EIO; 829 } 830 /* Extra delay required because the phy may not be completed with 831 * its reset when BMCR_RESET is cleared. Specs say 256 uS is 832 * enough delay but using 1ms here to be safe */ 833 msleep(1); 834 835 return 0; 836 } 837 838 static int smsc911x_phy_loopbacktest(struct net_device *dev) 839 { 840 struct smsc911x_data *pdata = netdev_priv(dev); 841 struct phy_device *phy_dev = dev->phydev; 842 int result = -EIO; 843 unsigned int i, val; 844 unsigned long flags; 845 846 /* Initialise tx packet using broadcast destination address */ 847 eth_broadcast_addr(pdata->loopback_tx_pkt); 848 849 /* Use incrementing source address */ 850 for (i = 6; i < 12; i++) 851 pdata->loopback_tx_pkt[i] = (char)i; 852 853 /* Set length type field */ 854 pdata->loopback_tx_pkt[12] = 0x00; 855 pdata->loopback_tx_pkt[13] = 0x00; 856 857 for (i = 14; i < MIN_PACKET_SIZE; i++) 858 pdata->loopback_tx_pkt[i] = (char)i; 859 860 val = smsc911x_reg_read(pdata, HW_CFG); 861 val &= HW_CFG_TX_FIF_SZ_; 862 val |= HW_CFG_SF_; 863 smsc911x_reg_write(pdata, HW_CFG, val); 864 865 smsc911x_reg_write(pdata, TX_CFG, TX_CFG_TX_ON_); 866 smsc911x_reg_write(pdata, RX_CFG, 867 (u32)((ulong)pdata->loopback_rx_pkt & 0x03) << 8); 868 869 for (i = 0; i < 10; i++) { 870 /* Set PHY to 10/FD, no ANEG, and loopback mode */ 871 smsc911x_mii_write(phy_dev->mdio.bus, phy_dev->mdio.addr, 872 MII_BMCR, BMCR_LOOPBACK | BMCR_FULLDPLX); 873 874 /* Enable MAC tx/rx, FD */ 875 spin_lock_irqsave(&pdata->mac_lock, flags); 876 smsc911x_mac_write(pdata, MAC_CR, MAC_CR_FDPX_ 877 | MAC_CR_TXEN_ | MAC_CR_RXEN_); 878 spin_unlock_irqrestore(&pdata->mac_lock, flags); 879 880 if (smsc911x_phy_check_loopbackpkt(pdata) == 0) { 881 result = 0; 882 break; 883 } 884 pdata->resetcount++; 885 886 /* Disable MAC rx */ 887 spin_lock_irqsave(&pdata->mac_lock, flags); 888 smsc911x_mac_write(pdata, MAC_CR, 0); 889 spin_unlock_irqrestore(&pdata->mac_lock, flags); 890 891 smsc911x_phy_reset(pdata); 892 } 893 894 /* Disable MAC */ 895 spin_lock_irqsave(&pdata->mac_lock, flags); 896 smsc911x_mac_write(pdata, MAC_CR, 0); 897 spin_unlock_irqrestore(&pdata->mac_lock, flags); 898 899 /* Cancel PHY loopback mode */ 900 smsc911x_mii_write(phy_dev->mdio.bus, phy_dev->mdio.addr, MII_BMCR, 0); 901 902 smsc911x_reg_write(pdata, TX_CFG, 0); 903 smsc911x_reg_write(pdata, RX_CFG, 0); 904 905 return result; 906 } 907 #endif /* USE_PHY_WORK_AROUND */ 908 909 static void smsc911x_phy_update_flowcontrol(struct smsc911x_data *pdata) 910 { 911 struct net_device *ndev = pdata->dev; 912 struct phy_device *phy_dev = ndev->phydev; 913 u32 afc = smsc911x_reg_read(pdata, AFC_CFG); 914 u32 flow; 915 unsigned long flags; 916 917 if (phy_dev->duplex == DUPLEX_FULL) { 918 u16 lcladv = phy_read(phy_dev, MII_ADVERTISE); 919 u16 rmtadv = phy_read(phy_dev, MII_LPA); 920 u8 cap = mii_resolve_flowctrl_fdx(lcladv, rmtadv); 921 922 if (cap & FLOW_CTRL_RX) 923 flow = 0xFFFF0002; 924 else 925 flow = 0; 926 927 if (cap & FLOW_CTRL_TX) 928 afc |= 0xF; 929 else 930 afc &= ~0xF; 931 932 SMSC_TRACE(pdata, hw, "rx pause %s, tx pause %s", 933 (cap & FLOW_CTRL_RX ? "enabled" : "disabled"), 934 (cap & FLOW_CTRL_TX ? "enabled" : "disabled")); 935 } else { 936 SMSC_TRACE(pdata, hw, "half duplex"); 937 flow = 0; 938 afc |= 0xF; 939 } 940 941 spin_lock_irqsave(&pdata->mac_lock, flags); 942 smsc911x_mac_write(pdata, FLOW, flow); 943 spin_unlock_irqrestore(&pdata->mac_lock, flags); 944 945 smsc911x_reg_write(pdata, AFC_CFG, afc); 946 } 947 948 /* Update link mode if anything has changed. Called periodically when the 949 * PHY is in polling mode, even if nothing has changed. */ 950 static void smsc911x_phy_adjust_link(struct net_device *dev) 951 { 952 struct smsc911x_data *pdata = netdev_priv(dev); 953 struct phy_device *phy_dev = dev->phydev; 954 unsigned long flags; 955 int carrier; 956 957 if (phy_dev->duplex != pdata->last_duplex) { 958 unsigned int mac_cr; 959 SMSC_TRACE(pdata, hw, "duplex state has changed"); 960 961 spin_lock_irqsave(&pdata->mac_lock, flags); 962 mac_cr = smsc911x_mac_read(pdata, MAC_CR); 963 if (phy_dev->duplex) { 964 SMSC_TRACE(pdata, hw, 965 "configuring for full duplex mode"); 966 mac_cr |= MAC_CR_FDPX_; 967 } else { 968 SMSC_TRACE(pdata, hw, 969 "configuring for half duplex mode"); 970 mac_cr &= ~MAC_CR_FDPX_; 971 } 972 smsc911x_mac_write(pdata, MAC_CR, mac_cr); 973 spin_unlock_irqrestore(&pdata->mac_lock, flags); 974 975 smsc911x_phy_update_flowcontrol(pdata); 976 pdata->last_duplex = phy_dev->duplex; 977 } 978 979 carrier = netif_carrier_ok(dev); 980 if (carrier != pdata->last_carrier) { 981 SMSC_TRACE(pdata, hw, "carrier state has changed"); 982 if (carrier) { 983 SMSC_TRACE(pdata, hw, "configuring for carrier OK"); 984 if ((pdata->gpio_orig_setting & GPIO_CFG_LED1_EN_) && 985 (!pdata->using_extphy)) { 986 /* Restore original GPIO configuration */ 987 pdata->gpio_setting = pdata->gpio_orig_setting; 988 smsc911x_reg_write(pdata, GPIO_CFG, 989 pdata->gpio_setting); 990 } 991 } else { 992 SMSC_TRACE(pdata, hw, "configuring for no carrier"); 993 /* Check global setting that LED1 994 * usage is 10/100 indicator */ 995 pdata->gpio_setting = smsc911x_reg_read(pdata, 996 GPIO_CFG); 997 if ((pdata->gpio_setting & GPIO_CFG_LED1_EN_) && 998 (!pdata->using_extphy)) { 999 /* Force 10/100 LED off, after saving 1000 * original GPIO configuration */ 1001 pdata->gpio_orig_setting = pdata->gpio_setting; 1002 1003 pdata->gpio_setting &= ~GPIO_CFG_LED1_EN_; 1004 pdata->gpio_setting |= (GPIO_CFG_GPIOBUF0_ 1005 | GPIO_CFG_GPIODIR0_ 1006 | GPIO_CFG_GPIOD0_); 1007 smsc911x_reg_write(pdata, GPIO_CFG, 1008 pdata->gpio_setting); 1009 } 1010 } 1011 pdata->last_carrier = carrier; 1012 } 1013 } 1014 1015 static int smsc911x_mii_probe(struct net_device *dev) 1016 { 1017 struct smsc911x_data *pdata = netdev_priv(dev); 1018 struct phy_device *phydev; 1019 int ret; 1020 1021 /* find the first phy */ 1022 phydev = phy_find_first(pdata->mii_bus); 1023 if (!phydev) { 1024 netdev_err(dev, "no PHY found\n"); 1025 return -ENODEV; 1026 } 1027 1028 SMSC_TRACE(pdata, probe, "PHY: addr %d, phy_id 0x%08X", 1029 phydev->mdio.addr, phydev->phy_id); 1030 1031 ret = phy_connect_direct(dev, phydev, &smsc911x_phy_adjust_link, 1032 pdata->config.phy_interface); 1033 1034 if (ret) { 1035 netdev_err(dev, "Could not attach to PHY\n"); 1036 return ret; 1037 } 1038 1039 phy_attached_info(phydev); 1040 1041 phy_set_max_speed(phydev, SPEED_100); 1042 1043 /* mask with MAC supported features */ 1044 phy_support_asym_pause(phydev); 1045 1046 pdata->last_duplex = -1; 1047 pdata->last_carrier = -1; 1048 1049 #ifdef USE_PHY_WORK_AROUND 1050 if (smsc911x_phy_loopbacktest(dev) < 0) { 1051 SMSC_WARN(pdata, hw, "Failed Loop Back Test"); 1052 phy_disconnect(phydev); 1053 return -ENODEV; 1054 } 1055 SMSC_TRACE(pdata, hw, "Passed Loop Back Test"); 1056 #endif /* USE_PHY_WORK_AROUND */ 1057 1058 SMSC_TRACE(pdata, hw, "phy initialised successfully"); 1059 return 0; 1060 } 1061 1062 static int smsc911x_mii_init(struct platform_device *pdev, 1063 struct net_device *dev) 1064 { 1065 struct smsc911x_data *pdata = netdev_priv(dev); 1066 struct phy_device *phydev; 1067 int err = -ENXIO; 1068 1069 pdata->mii_bus = mdiobus_alloc(); 1070 if (!pdata->mii_bus) { 1071 err = -ENOMEM; 1072 goto err_out_1; 1073 } 1074 1075 pdata->mii_bus->name = SMSC_MDIONAME; 1076 snprintf(pdata->mii_bus->id, MII_BUS_ID_SIZE, "%s-%x", 1077 pdev->name, pdev->id); 1078 pdata->mii_bus->priv = pdata; 1079 pdata->mii_bus->read = smsc911x_mii_read; 1080 pdata->mii_bus->write = smsc911x_mii_write; 1081 1082 pdata->mii_bus->parent = &pdev->dev; 1083 1084 switch (pdata->idrev & 0xFFFF0000) { 1085 case 0x01170000: 1086 case 0x01150000: 1087 case 0x117A0000: 1088 case 0x115A0000: 1089 /* External PHY supported, try to autodetect */ 1090 smsc911x_phy_initialise_external(pdata); 1091 break; 1092 default: 1093 SMSC_TRACE(pdata, hw, "External PHY is not supported, " 1094 "using internal PHY"); 1095 pdata->using_extphy = 0; 1096 break; 1097 } 1098 1099 if (!pdata->using_extphy) { 1100 /* Mask all PHYs except ID 1 (internal) */ 1101 pdata->mii_bus->phy_mask = ~(1 << 1); 1102 } 1103 1104 if (mdiobus_register(pdata->mii_bus)) { 1105 SMSC_WARN(pdata, probe, "Error registering mii bus"); 1106 goto err_out_free_bus_2; 1107 } 1108 1109 phydev = phy_find_first(pdata->mii_bus); 1110 if (phydev) 1111 phydev->mac_managed_pm = true; 1112 1113 return 0; 1114 1115 err_out_free_bus_2: 1116 mdiobus_free(pdata->mii_bus); 1117 err_out_1: 1118 return err; 1119 } 1120 1121 /* Gets the number of tx statuses in the fifo */ 1122 static unsigned int smsc911x_tx_get_txstatcount(struct smsc911x_data *pdata) 1123 { 1124 return (smsc911x_reg_read(pdata, TX_FIFO_INF) 1125 & TX_FIFO_INF_TSUSED_) >> 16; 1126 } 1127 1128 /* Reads tx statuses and increments counters where necessary */ 1129 static void smsc911x_tx_update_txcounters(struct net_device *dev) 1130 { 1131 struct smsc911x_data *pdata = netdev_priv(dev); 1132 unsigned int tx_stat; 1133 1134 while ((tx_stat = smsc911x_tx_get_txstatus(pdata)) != 0) { 1135 if (unlikely(tx_stat & 0x80000000)) { 1136 /* In this driver the packet tag is used as the packet 1137 * length. Since a packet length can never reach the 1138 * size of 0x8000, this bit is reserved. It is worth 1139 * noting that the "reserved bit" in the warning above 1140 * does not reference a hardware defined reserved bit 1141 * but rather a driver defined one. 1142 */ 1143 SMSC_WARN(pdata, hw, "Packet tag reserved bit is high"); 1144 } else { 1145 if (unlikely(tx_stat & TX_STS_ES_)) { 1146 dev->stats.tx_errors++; 1147 } else { 1148 dev->stats.tx_packets++; 1149 dev->stats.tx_bytes += (tx_stat >> 16); 1150 } 1151 if (unlikely(tx_stat & TX_STS_EXCESS_COL_)) { 1152 dev->stats.collisions += 16; 1153 dev->stats.tx_aborted_errors += 1; 1154 } else { 1155 dev->stats.collisions += 1156 ((tx_stat >> 3) & 0xF); 1157 } 1158 if (unlikely(tx_stat & TX_STS_LOST_CARRIER_)) 1159 dev->stats.tx_carrier_errors += 1; 1160 if (unlikely(tx_stat & TX_STS_LATE_COL_)) { 1161 dev->stats.collisions++; 1162 dev->stats.tx_aborted_errors++; 1163 } 1164 } 1165 } 1166 } 1167 1168 /* Increments the Rx error counters */ 1169 static void 1170 smsc911x_rx_counterrors(struct net_device *dev, unsigned int rxstat) 1171 { 1172 int crc_err = 0; 1173 1174 if (unlikely(rxstat & RX_STS_ES_)) { 1175 dev->stats.rx_errors++; 1176 if (unlikely(rxstat & RX_STS_CRC_ERR_)) { 1177 dev->stats.rx_crc_errors++; 1178 crc_err = 1; 1179 } 1180 } 1181 if (likely(!crc_err)) { 1182 if (unlikely((rxstat & RX_STS_FRAME_TYPE_) && 1183 (rxstat & RX_STS_LENGTH_ERR_))) 1184 dev->stats.rx_length_errors++; 1185 if (rxstat & RX_STS_MCAST_) 1186 dev->stats.multicast++; 1187 } 1188 } 1189 1190 /* Quickly dumps bad packets */ 1191 static void 1192 smsc911x_rx_fastforward(struct smsc911x_data *pdata, unsigned int pktwords) 1193 { 1194 if (likely(pktwords >= 4)) { 1195 unsigned int timeout = 500; 1196 unsigned int val; 1197 smsc911x_reg_write(pdata, RX_DP_CTRL, RX_DP_CTRL_RX_FFWD_); 1198 do { 1199 udelay(1); 1200 val = smsc911x_reg_read(pdata, RX_DP_CTRL); 1201 } while ((val & RX_DP_CTRL_RX_FFWD_) && --timeout); 1202 1203 if (unlikely(timeout == 0)) 1204 SMSC_WARN(pdata, hw, "Timed out waiting for " 1205 "RX FFWD to finish, RX_DP_CTRL: 0x%08X", val); 1206 } else { 1207 while (pktwords--) 1208 smsc911x_reg_read(pdata, RX_DATA_FIFO); 1209 } 1210 } 1211 1212 /* NAPI poll function */ 1213 static int smsc911x_poll(struct napi_struct *napi, int budget) 1214 { 1215 struct smsc911x_data *pdata = 1216 container_of(napi, struct smsc911x_data, napi); 1217 struct net_device *dev = pdata->dev; 1218 int npackets = 0; 1219 1220 while (npackets < budget) { 1221 unsigned int pktlength; 1222 unsigned int pktwords; 1223 struct sk_buff *skb; 1224 unsigned int rxstat = smsc911x_rx_get_rxstatus(pdata); 1225 1226 if (!rxstat) { 1227 unsigned int temp; 1228 /* We processed all packets available. Tell NAPI it can 1229 * stop polling then re-enable rx interrupts */ 1230 smsc911x_reg_write(pdata, INT_STS, INT_STS_RSFL_); 1231 napi_complete(napi); 1232 temp = smsc911x_reg_read(pdata, INT_EN); 1233 temp |= INT_EN_RSFL_EN_; 1234 smsc911x_reg_write(pdata, INT_EN, temp); 1235 break; 1236 } 1237 1238 /* Count packet for NAPI scheduling, even if it has an error. 1239 * Error packets still require cycles to discard */ 1240 npackets++; 1241 1242 pktlength = ((rxstat & 0x3FFF0000) >> 16); 1243 pktwords = (pktlength + NET_IP_ALIGN + 3) >> 2; 1244 smsc911x_rx_counterrors(dev, rxstat); 1245 1246 if (unlikely(rxstat & RX_STS_ES_)) { 1247 SMSC_WARN(pdata, rx_err, 1248 "Discarding packet with error bit set"); 1249 /* Packet has an error, discard it and continue with 1250 * the next */ 1251 smsc911x_rx_fastforward(pdata, pktwords); 1252 dev->stats.rx_dropped++; 1253 continue; 1254 } 1255 1256 skb = netdev_alloc_skb(dev, pktwords << 2); 1257 if (unlikely(!skb)) { 1258 SMSC_WARN(pdata, rx_err, 1259 "Unable to allocate skb for rx packet"); 1260 /* Drop the packet and stop this polling iteration */ 1261 smsc911x_rx_fastforward(pdata, pktwords); 1262 dev->stats.rx_dropped++; 1263 break; 1264 } 1265 1266 pdata->ops->rx_readfifo(pdata, 1267 (unsigned int *)skb->data, pktwords); 1268 1269 /* Align IP on 16B boundary */ 1270 skb_reserve(skb, NET_IP_ALIGN); 1271 skb_put(skb, pktlength - 4); 1272 skb->protocol = eth_type_trans(skb, dev); 1273 skb_checksum_none_assert(skb); 1274 netif_receive_skb(skb); 1275 1276 /* Update counters */ 1277 dev->stats.rx_packets++; 1278 dev->stats.rx_bytes += (pktlength - 4); 1279 } 1280 1281 /* Return total received packets */ 1282 return npackets; 1283 } 1284 1285 /* Returns hash bit number for given MAC address 1286 * Example: 1287 * 01 00 5E 00 00 01 -> returns bit number 31 */ 1288 static unsigned int smsc911x_hash(char addr[ETH_ALEN]) 1289 { 1290 return (ether_crc(ETH_ALEN, addr) >> 26) & 0x3f; 1291 } 1292 1293 static void smsc911x_rx_multicast_update(struct smsc911x_data *pdata) 1294 { 1295 /* Performs the multicast & mac_cr update. This is called when 1296 * safe on the current hardware, and with the mac_lock held */ 1297 unsigned int mac_cr; 1298 1299 SMSC_ASSERT_MAC_LOCK(pdata); 1300 1301 mac_cr = smsc911x_mac_read(pdata, MAC_CR); 1302 mac_cr |= pdata->set_bits_mask; 1303 mac_cr &= ~(pdata->clear_bits_mask); 1304 smsc911x_mac_write(pdata, MAC_CR, mac_cr); 1305 smsc911x_mac_write(pdata, HASHH, pdata->hashhi); 1306 smsc911x_mac_write(pdata, HASHL, pdata->hashlo); 1307 SMSC_TRACE(pdata, hw, "maccr 0x%08X, HASHH 0x%08X, HASHL 0x%08X", 1308 mac_cr, pdata->hashhi, pdata->hashlo); 1309 } 1310 1311 static void smsc911x_rx_multicast_update_workaround(struct smsc911x_data *pdata) 1312 { 1313 unsigned int mac_cr; 1314 1315 /* This function is only called for older LAN911x devices 1316 * (revA or revB), where MAC_CR, HASHH and HASHL should not 1317 * be modified during Rx - newer devices immediately update the 1318 * registers. 1319 * 1320 * This is called from interrupt context */ 1321 1322 spin_lock(&pdata->mac_lock); 1323 1324 /* Check Rx has stopped */ 1325 if (smsc911x_mac_read(pdata, MAC_CR) & MAC_CR_RXEN_) 1326 SMSC_WARN(pdata, drv, "Rx not stopped"); 1327 1328 /* Perform the update - safe to do now Rx has stopped */ 1329 smsc911x_rx_multicast_update(pdata); 1330 1331 /* Re-enable Rx */ 1332 mac_cr = smsc911x_mac_read(pdata, MAC_CR); 1333 mac_cr |= MAC_CR_RXEN_; 1334 smsc911x_mac_write(pdata, MAC_CR, mac_cr); 1335 1336 pdata->multicast_update_pending = 0; 1337 1338 spin_unlock(&pdata->mac_lock); 1339 } 1340 1341 static int smsc911x_phy_general_power_up(struct smsc911x_data *pdata) 1342 { 1343 struct net_device *ndev = pdata->dev; 1344 struct phy_device *phy_dev = ndev->phydev; 1345 int rc = 0; 1346 1347 if (!phy_dev) 1348 return rc; 1349 1350 /* If the internal PHY is in General Power-Down mode, all, except the 1351 * management interface, is powered-down and stays in that condition as 1352 * long as Phy register bit 0.11 is HIGH. 1353 * 1354 * In that case, clear the bit 0.11, so the PHY powers up and we can 1355 * access to the phy registers. 1356 */ 1357 rc = phy_read(phy_dev, MII_BMCR); 1358 if (rc < 0) { 1359 SMSC_WARN(pdata, drv, "Failed reading PHY control reg"); 1360 return rc; 1361 } 1362 1363 /* If the PHY general power-down bit is not set is not necessary to 1364 * disable the general power down-mode. 1365 */ 1366 if (rc & BMCR_PDOWN) { 1367 rc = phy_write(phy_dev, MII_BMCR, rc & ~BMCR_PDOWN); 1368 if (rc < 0) { 1369 SMSC_WARN(pdata, drv, "Failed writing PHY control reg"); 1370 return rc; 1371 } 1372 1373 usleep_range(1000, 1500); 1374 } 1375 1376 return 0; 1377 } 1378 1379 static int smsc911x_phy_disable_energy_detect(struct smsc911x_data *pdata) 1380 { 1381 struct net_device *ndev = pdata->dev; 1382 struct phy_device *phy_dev = ndev->phydev; 1383 int rc = 0; 1384 1385 if (!phy_dev) 1386 return rc; 1387 1388 rc = phy_read(phy_dev, MII_LAN83C185_CTRL_STATUS); 1389 1390 if (rc < 0) { 1391 SMSC_WARN(pdata, drv, "Failed reading PHY control reg"); 1392 return rc; 1393 } 1394 1395 /* Only disable if energy detect mode is already enabled */ 1396 if (rc & MII_LAN83C185_EDPWRDOWN) { 1397 /* Disable energy detect mode for this SMSC Transceivers */ 1398 rc = phy_write(phy_dev, MII_LAN83C185_CTRL_STATUS, 1399 rc & (~MII_LAN83C185_EDPWRDOWN)); 1400 1401 if (rc < 0) { 1402 SMSC_WARN(pdata, drv, "Failed writing PHY control reg"); 1403 return rc; 1404 } 1405 /* Allow PHY to wakeup */ 1406 mdelay(2); 1407 } 1408 1409 return 0; 1410 } 1411 1412 static int smsc911x_phy_enable_energy_detect(struct smsc911x_data *pdata) 1413 { 1414 struct net_device *ndev = pdata->dev; 1415 struct phy_device *phy_dev = ndev->phydev; 1416 int rc = 0; 1417 1418 if (!phy_dev) 1419 return rc; 1420 1421 rc = phy_read(phy_dev, MII_LAN83C185_CTRL_STATUS); 1422 1423 if (rc < 0) { 1424 SMSC_WARN(pdata, drv, "Failed reading PHY control reg"); 1425 return rc; 1426 } 1427 1428 /* Only enable if energy detect mode is already disabled */ 1429 if (!(rc & MII_LAN83C185_EDPWRDOWN)) { 1430 /* Enable energy detect mode for this SMSC Transceivers */ 1431 rc = phy_write(phy_dev, MII_LAN83C185_CTRL_STATUS, 1432 rc | MII_LAN83C185_EDPWRDOWN); 1433 1434 if (rc < 0) { 1435 SMSC_WARN(pdata, drv, "Failed writing PHY control reg"); 1436 return rc; 1437 } 1438 } 1439 return 0; 1440 } 1441 1442 static int smsc911x_soft_reset(struct smsc911x_data *pdata) 1443 { 1444 unsigned int timeout; 1445 unsigned int temp; 1446 int ret; 1447 unsigned int reset_offset = HW_CFG; 1448 unsigned int reset_mask = HW_CFG_SRST_; 1449 1450 /* 1451 * Make sure to power-up the PHY chip before doing a reset, otherwise 1452 * the reset fails. 1453 */ 1454 ret = smsc911x_phy_general_power_up(pdata); 1455 if (ret) { 1456 SMSC_WARN(pdata, drv, "Failed to power-up the PHY chip"); 1457 return ret; 1458 } 1459 1460 /* 1461 * LAN9210/LAN9211/LAN9220/LAN9221 chips have an internal PHY that 1462 * are initialized in a Energy Detect Power-Down mode that prevents 1463 * the MAC chip to be software reseted. So we have to wakeup the PHY 1464 * before. 1465 */ 1466 if (pdata->generation == 4) { 1467 ret = smsc911x_phy_disable_energy_detect(pdata); 1468 1469 if (ret) { 1470 SMSC_WARN(pdata, drv, "Failed to wakeup the PHY chip"); 1471 return ret; 1472 } 1473 } 1474 1475 if ((pdata->idrev & 0xFFFF0000) == LAN9250) { 1476 /* special reset for LAN9250 */ 1477 reset_offset = RESET_CTL; 1478 reset_mask = RESET_CTL_DIGITAL_RST_; 1479 } 1480 1481 /* Reset the LAN911x */ 1482 smsc911x_reg_write(pdata, reset_offset, reset_mask); 1483 1484 /* verify reset bit is cleared */ 1485 timeout = 10; 1486 do { 1487 udelay(10); 1488 temp = smsc911x_reg_read(pdata, reset_offset); 1489 } while ((--timeout) && (temp & reset_mask)); 1490 1491 if (unlikely(temp & reset_mask)) { 1492 SMSC_WARN(pdata, drv, "Failed to complete reset"); 1493 return -EIO; 1494 } 1495 1496 if (pdata->generation == 4) { 1497 ret = smsc911x_phy_enable_energy_detect(pdata); 1498 1499 if (ret) { 1500 SMSC_WARN(pdata, drv, "Failed to wakeup the PHY chip"); 1501 return ret; 1502 } 1503 } 1504 1505 return 0; 1506 } 1507 1508 /* Sets the device MAC address to dev_addr, called with mac_lock held */ 1509 static void 1510 smsc911x_set_hw_mac_address(struct smsc911x_data *pdata, const u8 dev_addr[6]) 1511 { 1512 u32 mac_high16 = (dev_addr[5] << 8) | dev_addr[4]; 1513 u32 mac_low32 = (dev_addr[3] << 24) | (dev_addr[2] << 16) | 1514 (dev_addr[1] << 8) | dev_addr[0]; 1515 1516 SMSC_ASSERT_MAC_LOCK(pdata); 1517 1518 smsc911x_mac_write(pdata, ADDRH, mac_high16); 1519 smsc911x_mac_write(pdata, ADDRL, mac_low32); 1520 } 1521 1522 static void smsc911x_disable_irq_chip(struct net_device *dev) 1523 { 1524 struct smsc911x_data *pdata = netdev_priv(dev); 1525 1526 smsc911x_reg_write(pdata, INT_EN, 0); 1527 smsc911x_reg_write(pdata, INT_STS, 0xFFFFFFFF); 1528 } 1529 1530 static irqreturn_t smsc911x_irqhandler(int irq, void *dev_id) 1531 { 1532 struct net_device *dev = dev_id; 1533 struct smsc911x_data *pdata = netdev_priv(dev); 1534 u32 intsts = smsc911x_reg_read(pdata, INT_STS); 1535 u32 inten = smsc911x_reg_read(pdata, INT_EN); 1536 int serviced = IRQ_NONE; 1537 u32 temp; 1538 1539 if (unlikely(intsts & inten & INT_STS_SW_INT_)) { 1540 temp = smsc911x_reg_read(pdata, INT_EN); 1541 temp &= (~INT_EN_SW_INT_EN_); 1542 smsc911x_reg_write(pdata, INT_EN, temp); 1543 smsc911x_reg_write(pdata, INT_STS, INT_STS_SW_INT_); 1544 pdata->software_irq_signal = 1; 1545 smp_wmb(); 1546 serviced = IRQ_HANDLED; 1547 } 1548 1549 if (unlikely(intsts & inten & INT_STS_RXSTOP_INT_)) { 1550 /* Called when there is a multicast update scheduled and 1551 * it is now safe to complete the update */ 1552 SMSC_TRACE(pdata, intr, "RX Stop interrupt"); 1553 smsc911x_reg_write(pdata, INT_STS, INT_STS_RXSTOP_INT_); 1554 if (pdata->multicast_update_pending) 1555 smsc911x_rx_multicast_update_workaround(pdata); 1556 serviced = IRQ_HANDLED; 1557 } 1558 1559 if (intsts & inten & INT_STS_TDFA_) { 1560 temp = smsc911x_reg_read(pdata, FIFO_INT); 1561 temp |= FIFO_INT_TX_AVAIL_LEVEL_; 1562 smsc911x_reg_write(pdata, FIFO_INT, temp); 1563 smsc911x_reg_write(pdata, INT_STS, INT_STS_TDFA_); 1564 netif_wake_queue(dev); 1565 serviced = IRQ_HANDLED; 1566 } 1567 1568 if (unlikely(intsts & inten & INT_STS_RXE_)) { 1569 SMSC_TRACE(pdata, intr, "RX Error interrupt"); 1570 smsc911x_reg_write(pdata, INT_STS, INT_STS_RXE_); 1571 serviced = IRQ_HANDLED; 1572 } 1573 1574 if (likely(intsts & inten & INT_STS_RSFL_)) { 1575 if (likely(napi_schedule_prep(&pdata->napi))) { 1576 /* Disable Rx interrupts */ 1577 temp = smsc911x_reg_read(pdata, INT_EN); 1578 temp &= (~INT_EN_RSFL_EN_); 1579 smsc911x_reg_write(pdata, INT_EN, temp); 1580 /* Schedule a NAPI poll */ 1581 __napi_schedule(&pdata->napi); 1582 } else { 1583 SMSC_WARN(pdata, rx_err, "napi_schedule_prep failed"); 1584 } 1585 serviced = IRQ_HANDLED; 1586 } 1587 1588 return serviced; 1589 } 1590 1591 static int smsc911x_open(struct net_device *dev) 1592 { 1593 struct smsc911x_data *pdata = netdev_priv(dev); 1594 unsigned int timeout; 1595 unsigned int temp; 1596 unsigned int intcfg; 1597 int retval; 1598 int irq_flags; 1599 1600 pm_runtime_get_sync(dev->dev.parent); 1601 1602 /* find and start the given phy */ 1603 if (!dev->phydev) { 1604 retval = smsc911x_mii_probe(dev); 1605 if (retval < 0) { 1606 SMSC_WARN(pdata, probe, "Error starting phy"); 1607 goto out; 1608 } 1609 } 1610 1611 /* Reset the LAN911x */ 1612 retval = smsc911x_soft_reset(pdata); 1613 if (retval) { 1614 SMSC_WARN(pdata, hw, "soft reset failed"); 1615 goto mii_free_out; 1616 } 1617 1618 smsc911x_reg_write(pdata, HW_CFG, 0x00050000); 1619 smsc911x_reg_write(pdata, AFC_CFG, 0x006E3740); 1620 1621 /* Increase the legal frame size of VLAN tagged frames to 1522 bytes */ 1622 spin_lock_irq(&pdata->mac_lock); 1623 smsc911x_mac_write(pdata, VLAN1, ETH_P_8021Q); 1624 spin_unlock_irq(&pdata->mac_lock); 1625 1626 /* Make sure EEPROM has finished loading before setting GPIO_CFG */ 1627 timeout = 50; 1628 while ((smsc911x_reg_read(pdata, E2P_CMD) & E2P_CMD_EPC_BUSY_) && 1629 --timeout) { 1630 udelay(10); 1631 } 1632 1633 if (unlikely(timeout == 0)) 1634 SMSC_WARN(pdata, ifup, 1635 "Timed out waiting for EEPROM busy bit to clear"); 1636 1637 smsc911x_reg_write(pdata, GPIO_CFG, 0x70070000); 1638 1639 /* The soft reset above cleared the device's MAC address, 1640 * restore it from local copy (set in probe) */ 1641 spin_lock_irq(&pdata->mac_lock); 1642 smsc911x_set_hw_mac_address(pdata, dev->dev_addr); 1643 spin_unlock_irq(&pdata->mac_lock); 1644 1645 /* Initialise irqs, but leave all sources disabled */ 1646 smsc911x_disable_irq_chip(dev); 1647 1648 /* Set interrupt deassertion to 100uS */ 1649 intcfg = ((10 << 24) | INT_CFG_IRQ_EN_); 1650 1651 if (pdata->config.irq_polarity) { 1652 SMSC_TRACE(pdata, ifup, "irq polarity: active high"); 1653 intcfg |= INT_CFG_IRQ_POL_; 1654 } else { 1655 SMSC_TRACE(pdata, ifup, "irq polarity: active low"); 1656 } 1657 1658 if (pdata->config.irq_type) { 1659 SMSC_TRACE(pdata, ifup, "irq type: push-pull"); 1660 intcfg |= INT_CFG_IRQ_TYPE_; 1661 } else { 1662 SMSC_TRACE(pdata, ifup, "irq type: open drain"); 1663 } 1664 1665 smsc911x_reg_write(pdata, INT_CFG, intcfg); 1666 1667 SMSC_TRACE(pdata, ifup, "Testing irq handler using IRQ %d", dev->irq); 1668 pdata->software_irq_signal = 0; 1669 smp_wmb(); 1670 1671 irq_flags = irq_get_trigger_type(dev->irq); 1672 retval = request_irq(dev->irq, smsc911x_irqhandler, 1673 irq_flags | IRQF_SHARED, dev->name, dev); 1674 if (retval) { 1675 SMSC_WARN(pdata, probe, 1676 "Unable to claim requested irq: %d", dev->irq); 1677 goto mii_free_out; 1678 } 1679 1680 temp = smsc911x_reg_read(pdata, INT_EN); 1681 temp |= INT_EN_SW_INT_EN_; 1682 smsc911x_reg_write(pdata, INT_EN, temp); 1683 1684 timeout = 1000; 1685 while (timeout--) { 1686 if (pdata->software_irq_signal) 1687 break; 1688 msleep(1); 1689 } 1690 1691 if (!pdata->software_irq_signal) { 1692 netdev_warn(dev, "ISR failed signaling test (IRQ %d)\n", 1693 dev->irq); 1694 retval = -ENODEV; 1695 goto irq_stop_out; 1696 } 1697 SMSC_TRACE(pdata, ifup, "IRQ handler passed test using IRQ %d", 1698 dev->irq); 1699 1700 netdev_info(dev, "SMSC911x/921x identified at %#08lx, IRQ: %d\n", 1701 (unsigned long)pdata->ioaddr, dev->irq); 1702 1703 /* Reset the last known duplex and carrier */ 1704 pdata->last_duplex = -1; 1705 pdata->last_carrier = -1; 1706 1707 /* Bring the PHY up */ 1708 phy_start(dev->phydev); 1709 1710 temp = smsc911x_reg_read(pdata, HW_CFG); 1711 /* Preserve TX FIFO size and external PHY configuration */ 1712 temp &= (HW_CFG_TX_FIF_SZ_|0x00000FFF); 1713 temp |= HW_CFG_SF_; 1714 smsc911x_reg_write(pdata, HW_CFG, temp); 1715 1716 temp = smsc911x_reg_read(pdata, FIFO_INT); 1717 temp |= FIFO_INT_TX_AVAIL_LEVEL_; 1718 temp &= ~(FIFO_INT_RX_STS_LEVEL_); 1719 smsc911x_reg_write(pdata, FIFO_INT, temp); 1720 1721 /* set RX Data offset to 2 bytes for alignment */ 1722 smsc911x_reg_write(pdata, RX_CFG, (NET_IP_ALIGN << 8)); 1723 1724 /* enable NAPI polling before enabling RX interrupts */ 1725 napi_enable(&pdata->napi); 1726 1727 temp = smsc911x_reg_read(pdata, INT_EN); 1728 temp |= (INT_EN_TDFA_EN_ | INT_EN_RSFL_EN_ | INT_EN_RXSTOP_INT_EN_); 1729 smsc911x_reg_write(pdata, INT_EN, temp); 1730 1731 spin_lock_irq(&pdata->mac_lock); 1732 temp = smsc911x_mac_read(pdata, MAC_CR); 1733 temp |= (MAC_CR_TXEN_ | MAC_CR_RXEN_ | MAC_CR_HBDIS_); 1734 smsc911x_mac_write(pdata, MAC_CR, temp); 1735 spin_unlock_irq(&pdata->mac_lock); 1736 1737 smsc911x_reg_write(pdata, TX_CFG, TX_CFG_TX_ON_); 1738 1739 netif_start_queue(dev); 1740 return 0; 1741 1742 irq_stop_out: 1743 free_irq(dev->irq, dev); 1744 mii_free_out: 1745 phy_disconnect(dev->phydev); 1746 out: 1747 pm_runtime_put(dev->dev.parent); 1748 return retval; 1749 } 1750 1751 /* Entry point for stopping the interface */ 1752 static int smsc911x_stop(struct net_device *dev) 1753 { 1754 struct smsc911x_data *pdata = netdev_priv(dev); 1755 unsigned int temp; 1756 1757 /* Disable all device interrupts */ 1758 temp = smsc911x_reg_read(pdata, INT_CFG); 1759 temp &= ~INT_CFG_IRQ_EN_; 1760 smsc911x_reg_write(pdata, INT_CFG, temp); 1761 1762 /* Stop Tx and Rx polling */ 1763 netif_stop_queue(dev); 1764 napi_disable(&pdata->napi); 1765 1766 /* At this point all Rx and Tx activity is stopped */ 1767 dev->stats.rx_dropped += smsc911x_reg_read(pdata, RX_DROP); 1768 smsc911x_tx_update_txcounters(dev); 1769 1770 free_irq(dev->irq, dev); 1771 1772 /* Bring the PHY down */ 1773 if (dev->phydev) { 1774 phy_stop(dev->phydev); 1775 phy_disconnect(dev->phydev); 1776 } 1777 netif_carrier_off(dev); 1778 pm_runtime_put(dev->dev.parent); 1779 1780 SMSC_TRACE(pdata, ifdown, "Interface stopped"); 1781 return 0; 1782 } 1783 1784 /* Entry point for transmitting a packet */ 1785 static netdev_tx_t 1786 smsc911x_hard_start_xmit(struct sk_buff *skb, struct net_device *dev) 1787 { 1788 struct smsc911x_data *pdata = netdev_priv(dev); 1789 unsigned int freespace; 1790 unsigned int tx_cmd_a; 1791 unsigned int tx_cmd_b; 1792 unsigned int temp; 1793 u32 wrsz; 1794 ulong bufp; 1795 1796 freespace = smsc911x_reg_read(pdata, TX_FIFO_INF) & TX_FIFO_INF_TDFREE_; 1797 1798 if (unlikely(freespace < TX_FIFO_LOW_THRESHOLD)) 1799 SMSC_WARN(pdata, tx_err, 1800 "Tx data fifo low, space available: %d", freespace); 1801 1802 /* Word alignment adjustment */ 1803 tx_cmd_a = (u32)((ulong)skb->data & 0x03) << 16; 1804 tx_cmd_a |= TX_CMD_A_FIRST_SEG_ | TX_CMD_A_LAST_SEG_; 1805 tx_cmd_a |= (unsigned int)skb->len; 1806 1807 tx_cmd_b = ((unsigned int)skb->len) << 16; 1808 tx_cmd_b |= (unsigned int)skb->len; 1809 1810 smsc911x_reg_write(pdata, TX_DATA_FIFO, tx_cmd_a); 1811 smsc911x_reg_write(pdata, TX_DATA_FIFO, tx_cmd_b); 1812 1813 bufp = (ulong)skb->data & (~0x3); 1814 wrsz = (u32)skb->len + 3; 1815 wrsz += (u32)((ulong)skb->data & 0x3); 1816 wrsz >>= 2; 1817 1818 pdata->ops->tx_writefifo(pdata, (unsigned int *)bufp, wrsz); 1819 freespace -= (skb->len + 32); 1820 skb_tx_timestamp(skb); 1821 dev_consume_skb_any(skb); 1822 1823 if (unlikely(smsc911x_tx_get_txstatcount(pdata) >= 30)) 1824 smsc911x_tx_update_txcounters(dev); 1825 1826 if (freespace < TX_FIFO_LOW_THRESHOLD) { 1827 netif_stop_queue(dev); 1828 temp = smsc911x_reg_read(pdata, FIFO_INT); 1829 temp &= 0x00FFFFFF; 1830 temp |= 0x32000000; 1831 smsc911x_reg_write(pdata, FIFO_INT, temp); 1832 } 1833 1834 return NETDEV_TX_OK; 1835 } 1836 1837 /* Entry point for getting status counters */ 1838 static struct net_device_stats *smsc911x_get_stats(struct net_device *dev) 1839 { 1840 struct smsc911x_data *pdata = netdev_priv(dev); 1841 smsc911x_tx_update_txcounters(dev); 1842 dev->stats.rx_dropped += smsc911x_reg_read(pdata, RX_DROP); 1843 return &dev->stats; 1844 } 1845 1846 /* Entry point for setting addressing modes */ 1847 static void smsc911x_set_multicast_list(struct net_device *dev) 1848 { 1849 struct smsc911x_data *pdata = netdev_priv(dev); 1850 unsigned long flags; 1851 1852 if (dev->flags & IFF_PROMISC) { 1853 /* Enabling promiscuous mode */ 1854 pdata->set_bits_mask = MAC_CR_PRMS_; 1855 pdata->clear_bits_mask = (MAC_CR_MCPAS_ | MAC_CR_HPFILT_); 1856 pdata->hashhi = 0; 1857 pdata->hashlo = 0; 1858 } else if (dev->flags & IFF_ALLMULTI) { 1859 /* Enabling all multicast mode */ 1860 pdata->set_bits_mask = MAC_CR_MCPAS_; 1861 pdata->clear_bits_mask = (MAC_CR_PRMS_ | MAC_CR_HPFILT_); 1862 pdata->hashhi = 0; 1863 pdata->hashlo = 0; 1864 } else if (!netdev_mc_empty(dev)) { 1865 /* Enabling specific multicast addresses */ 1866 unsigned int hash_high = 0; 1867 unsigned int hash_low = 0; 1868 struct netdev_hw_addr *ha; 1869 1870 pdata->set_bits_mask = MAC_CR_HPFILT_; 1871 pdata->clear_bits_mask = (MAC_CR_PRMS_ | MAC_CR_MCPAS_); 1872 1873 netdev_for_each_mc_addr(ha, dev) { 1874 unsigned int bitnum = smsc911x_hash(ha->addr); 1875 unsigned int mask = 0x01 << (bitnum & 0x1F); 1876 1877 if (bitnum & 0x20) 1878 hash_high |= mask; 1879 else 1880 hash_low |= mask; 1881 } 1882 1883 pdata->hashhi = hash_high; 1884 pdata->hashlo = hash_low; 1885 } else { 1886 /* Enabling local MAC address only */ 1887 pdata->set_bits_mask = 0; 1888 pdata->clear_bits_mask = 1889 (MAC_CR_PRMS_ | MAC_CR_MCPAS_ | MAC_CR_HPFILT_); 1890 pdata->hashhi = 0; 1891 pdata->hashlo = 0; 1892 } 1893 1894 spin_lock_irqsave(&pdata->mac_lock, flags); 1895 1896 if (pdata->generation <= 1) { 1897 /* Older hardware revision - cannot change these flags while 1898 * receiving data */ 1899 if (!pdata->multicast_update_pending) { 1900 unsigned int temp; 1901 SMSC_TRACE(pdata, hw, "scheduling mcast update"); 1902 pdata->multicast_update_pending = 1; 1903 1904 /* Request the hardware to stop, then perform the 1905 * update when we get an RX_STOP interrupt */ 1906 temp = smsc911x_mac_read(pdata, MAC_CR); 1907 temp &= ~(MAC_CR_RXEN_); 1908 smsc911x_mac_write(pdata, MAC_CR, temp); 1909 } else { 1910 /* There is another update pending, this should now 1911 * use the newer values */ 1912 } 1913 } else { 1914 /* Newer hardware revision - can write immediately */ 1915 smsc911x_rx_multicast_update(pdata); 1916 } 1917 1918 spin_unlock_irqrestore(&pdata->mac_lock, flags); 1919 } 1920 1921 #ifdef CONFIG_NET_POLL_CONTROLLER 1922 static void smsc911x_poll_controller(struct net_device *dev) 1923 { 1924 disable_irq(dev->irq); 1925 smsc911x_irqhandler(0, dev); 1926 enable_irq(dev->irq); 1927 } 1928 #endif /* CONFIG_NET_POLL_CONTROLLER */ 1929 1930 static int smsc911x_set_mac_address(struct net_device *dev, void *p) 1931 { 1932 struct smsc911x_data *pdata = netdev_priv(dev); 1933 struct sockaddr *addr = p; 1934 1935 /* On older hardware revisions we cannot change the mac address 1936 * registers while receiving data. Newer devices can safely change 1937 * this at any time. */ 1938 if (pdata->generation <= 1 && netif_running(dev)) 1939 return -EBUSY; 1940 1941 if (!is_valid_ether_addr(addr->sa_data)) 1942 return -EADDRNOTAVAIL; 1943 1944 eth_hw_addr_set(dev, addr->sa_data); 1945 1946 spin_lock_irq(&pdata->mac_lock); 1947 smsc911x_set_hw_mac_address(pdata, dev->dev_addr); 1948 spin_unlock_irq(&pdata->mac_lock); 1949 1950 netdev_info(dev, "MAC Address: %pM\n", dev->dev_addr); 1951 1952 return 0; 1953 } 1954 1955 static void smsc911x_ethtool_getdrvinfo(struct net_device *dev, 1956 struct ethtool_drvinfo *info) 1957 { 1958 strscpy(info->driver, SMSC_CHIPNAME, sizeof(info->driver)); 1959 strscpy(info->version, SMSC_DRV_VERSION, sizeof(info->version)); 1960 strscpy(info->bus_info, dev_name(dev->dev.parent), 1961 sizeof(info->bus_info)); 1962 } 1963 1964 static u32 smsc911x_ethtool_getmsglevel(struct net_device *dev) 1965 { 1966 struct smsc911x_data *pdata = netdev_priv(dev); 1967 return pdata->msg_enable; 1968 } 1969 1970 static void smsc911x_ethtool_setmsglevel(struct net_device *dev, u32 level) 1971 { 1972 struct smsc911x_data *pdata = netdev_priv(dev); 1973 pdata->msg_enable = level; 1974 } 1975 1976 static int smsc911x_ethtool_getregslen(struct net_device *dev) 1977 { 1978 return (((E2P_DATA - ID_REV) / 4 + 1) + (WUCSR - MAC_CR) + 1 + 32) * 1979 sizeof(u32); 1980 } 1981 1982 static void 1983 smsc911x_ethtool_getregs(struct net_device *dev, struct ethtool_regs *regs, 1984 void *buf) 1985 { 1986 struct smsc911x_data *pdata = netdev_priv(dev); 1987 struct phy_device *phy_dev = dev->phydev; 1988 unsigned long flags; 1989 unsigned int i; 1990 unsigned int j = 0; 1991 u32 *data = buf; 1992 1993 regs->version = pdata->idrev; 1994 for (i = ID_REV; i <= E2P_DATA; i += (sizeof(u32))) 1995 data[j++] = smsc911x_reg_read(pdata, i); 1996 1997 for (i = MAC_CR; i <= WUCSR; i++) { 1998 spin_lock_irqsave(&pdata->mac_lock, flags); 1999 data[j++] = smsc911x_mac_read(pdata, i); 2000 spin_unlock_irqrestore(&pdata->mac_lock, flags); 2001 } 2002 2003 for (i = 0; i <= 31; i++) 2004 data[j++] = smsc911x_mii_read(phy_dev->mdio.bus, 2005 phy_dev->mdio.addr, i); 2006 } 2007 2008 static void smsc911x_eeprom_enable_access(struct smsc911x_data *pdata) 2009 { 2010 unsigned int temp = smsc911x_reg_read(pdata, GPIO_CFG); 2011 temp &= ~GPIO_CFG_EEPR_EN_; 2012 smsc911x_reg_write(pdata, GPIO_CFG, temp); 2013 msleep(1); 2014 } 2015 2016 static int smsc911x_eeprom_send_cmd(struct smsc911x_data *pdata, u32 op) 2017 { 2018 int timeout = 100; 2019 u32 e2cmd; 2020 2021 SMSC_TRACE(pdata, drv, "op 0x%08x", op); 2022 if (smsc911x_reg_read(pdata, E2P_CMD) & E2P_CMD_EPC_BUSY_) { 2023 SMSC_WARN(pdata, drv, "Busy at start"); 2024 return -EBUSY; 2025 } 2026 2027 e2cmd = op | E2P_CMD_EPC_BUSY_; 2028 smsc911x_reg_write(pdata, E2P_CMD, e2cmd); 2029 2030 do { 2031 msleep(1); 2032 e2cmd = smsc911x_reg_read(pdata, E2P_CMD); 2033 } while ((e2cmd & E2P_CMD_EPC_BUSY_) && (--timeout)); 2034 2035 if (!timeout) { 2036 SMSC_TRACE(pdata, drv, "TIMED OUT"); 2037 return -EAGAIN; 2038 } 2039 2040 if (e2cmd & E2P_CMD_EPC_TIMEOUT_) { 2041 SMSC_TRACE(pdata, drv, "Error occurred during eeprom operation"); 2042 return -EINVAL; 2043 } 2044 2045 return 0; 2046 } 2047 2048 static int smsc911x_eeprom_read_location(struct smsc911x_data *pdata, 2049 u8 address, u8 *data) 2050 { 2051 u32 op = E2P_CMD_EPC_CMD_READ_ | address; 2052 int ret; 2053 2054 SMSC_TRACE(pdata, drv, "address 0x%x", address); 2055 ret = smsc911x_eeprom_send_cmd(pdata, op); 2056 2057 if (!ret) 2058 data[address] = smsc911x_reg_read(pdata, E2P_DATA); 2059 2060 return ret; 2061 } 2062 2063 static int smsc911x_eeprom_write_location(struct smsc911x_data *pdata, 2064 u8 address, u8 data) 2065 { 2066 u32 op = E2P_CMD_EPC_CMD_ERASE_ | address; 2067 int ret; 2068 2069 SMSC_TRACE(pdata, drv, "address 0x%x, data 0x%x", address, data); 2070 ret = smsc911x_eeprom_send_cmd(pdata, op); 2071 2072 if (!ret) { 2073 op = E2P_CMD_EPC_CMD_WRITE_ | address; 2074 smsc911x_reg_write(pdata, E2P_DATA, (u32)data); 2075 2076 /* Workaround for hardware read-after-write restriction */ 2077 smsc911x_reg_read(pdata, BYTE_TEST); 2078 2079 ret = smsc911x_eeprom_send_cmd(pdata, op); 2080 } 2081 2082 return ret; 2083 } 2084 2085 static int smsc911x_ethtool_get_eeprom_len(struct net_device *dev) 2086 { 2087 return SMSC911X_EEPROM_SIZE; 2088 } 2089 2090 static int smsc911x_ethtool_get_eeprom(struct net_device *dev, 2091 struct ethtool_eeprom *eeprom, u8 *data) 2092 { 2093 struct smsc911x_data *pdata = netdev_priv(dev); 2094 u8 eeprom_data[SMSC911X_EEPROM_SIZE]; 2095 int len; 2096 int i; 2097 2098 smsc911x_eeprom_enable_access(pdata); 2099 2100 len = min(eeprom->len, SMSC911X_EEPROM_SIZE); 2101 for (i = 0; i < len; i++) { 2102 int ret = smsc911x_eeprom_read_location(pdata, i, eeprom_data); 2103 if (ret < 0) { 2104 eeprom->len = 0; 2105 return ret; 2106 } 2107 } 2108 2109 memcpy(data, &eeprom_data[eeprom->offset], len); 2110 eeprom->len = len; 2111 return 0; 2112 } 2113 2114 static int smsc911x_ethtool_set_eeprom(struct net_device *dev, 2115 struct ethtool_eeprom *eeprom, u8 *data) 2116 { 2117 int ret; 2118 struct smsc911x_data *pdata = netdev_priv(dev); 2119 2120 smsc911x_eeprom_enable_access(pdata); 2121 smsc911x_eeprom_send_cmd(pdata, E2P_CMD_EPC_CMD_EWEN_); 2122 ret = smsc911x_eeprom_write_location(pdata, eeprom->offset, *data); 2123 smsc911x_eeprom_send_cmd(pdata, E2P_CMD_EPC_CMD_EWDS_); 2124 2125 /* Single byte write, according to man page */ 2126 eeprom->len = 1; 2127 2128 return ret; 2129 } 2130 2131 static const struct ethtool_ops smsc911x_ethtool_ops = { 2132 .get_link = ethtool_op_get_link, 2133 .get_drvinfo = smsc911x_ethtool_getdrvinfo, 2134 .nway_reset = phy_ethtool_nway_reset, 2135 .get_msglevel = smsc911x_ethtool_getmsglevel, 2136 .set_msglevel = smsc911x_ethtool_setmsglevel, 2137 .get_regs_len = smsc911x_ethtool_getregslen, 2138 .get_regs = smsc911x_ethtool_getregs, 2139 .get_eeprom_len = smsc911x_ethtool_get_eeprom_len, 2140 .get_eeprom = smsc911x_ethtool_get_eeprom, 2141 .set_eeprom = smsc911x_ethtool_set_eeprom, 2142 .get_ts_info = ethtool_op_get_ts_info, 2143 .get_link_ksettings = phy_ethtool_get_link_ksettings, 2144 .set_link_ksettings = phy_ethtool_set_link_ksettings, 2145 }; 2146 2147 static const struct net_device_ops smsc911x_netdev_ops = { 2148 .ndo_open = smsc911x_open, 2149 .ndo_stop = smsc911x_stop, 2150 .ndo_start_xmit = smsc911x_hard_start_xmit, 2151 .ndo_get_stats = smsc911x_get_stats, 2152 .ndo_set_rx_mode = smsc911x_set_multicast_list, 2153 .ndo_eth_ioctl = phy_do_ioctl_running, 2154 .ndo_validate_addr = eth_validate_addr, 2155 .ndo_set_mac_address = smsc911x_set_mac_address, 2156 #ifdef CONFIG_NET_POLL_CONTROLLER 2157 .ndo_poll_controller = smsc911x_poll_controller, 2158 #endif 2159 }; 2160 2161 /* copies the current mac address from hardware to dev->dev_addr */ 2162 static void smsc911x_read_mac_address(struct net_device *dev) 2163 { 2164 struct smsc911x_data *pdata = netdev_priv(dev); 2165 u32 mac_high16 = smsc911x_mac_read(pdata, ADDRH); 2166 u32 mac_low32 = smsc911x_mac_read(pdata, ADDRL); 2167 u8 addr[ETH_ALEN]; 2168 2169 addr[0] = (u8)(mac_low32); 2170 addr[1] = (u8)(mac_low32 >> 8); 2171 addr[2] = (u8)(mac_low32 >> 16); 2172 addr[3] = (u8)(mac_low32 >> 24); 2173 addr[4] = (u8)(mac_high16); 2174 addr[5] = (u8)(mac_high16 >> 8); 2175 eth_hw_addr_set(dev, addr); 2176 } 2177 2178 /* Initializing private device structures, only called from probe */ 2179 static int smsc911x_init(struct net_device *dev) 2180 { 2181 struct smsc911x_data *pdata = netdev_priv(dev); 2182 unsigned int byte_test, mask; 2183 unsigned int to = 100; 2184 2185 SMSC_TRACE(pdata, probe, "Driver Parameters:"); 2186 SMSC_TRACE(pdata, probe, "LAN base: 0x%08lX", 2187 (unsigned long)pdata->ioaddr); 2188 SMSC_TRACE(pdata, probe, "IRQ: %d", dev->irq); 2189 SMSC_TRACE(pdata, probe, "PHY will be autodetected."); 2190 2191 spin_lock_init(&pdata->dev_lock); 2192 spin_lock_init(&pdata->mac_lock); 2193 2194 if (pdata->ioaddr == NULL) { 2195 SMSC_WARN(pdata, probe, "pdata->ioaddr: 0x00000000"); 2196 return -ENODEV; 2197 } 2198 2199 /* 2200 * poll the READY bit in PMT_CTRL. Any other access to the device is 2201 * forbidden while this bit isn't set. Try for 100ms 2202 * 2203 * Note that this test is done before the WORD_SWAP register is 2204 * programmed. So in some configurations the READY bit is at 16 before 2205 * WORD_SWAP is written to. This issue is worked around by waiting 2206 * until either bit 0 or bit 16 gets set in PMT_CTRL. 2207 * 2208 * SMSC has confirmed that checking bit 16 (marked as reserved in 2209 * the datasheet) is fine since these bits "will either never be set 2210 * or can only go high after READY does (so also indicate the device 2211 * is ready)". 2212 */ 2213 2214 mask = PMT_CTRL_READY_ | swahw32(PMT_CTRL_READY_); 2215 while (!(smsc911x_reg_read(pdata, PMT_CTRL) & mask) && --to) 2216 udelay(1000); 2217 2218 if (to == 0) { 2219 netdev_err(dev, "Device not READY in 100ms aborting\n"); 2220 return -ENODEV; 2221 } 2222 2223 /* Check byte ordering */ 2224 byte_test = smsc911x_reg_read(pdata, BYTE_TEST); 2225 SMSC_TRACE(pdata, probe, "BYTE_TEST: 0x%08X", byte_test); 2226 if (byte_test == 0x43218765) { 2227 SMSC_TRACE(pdata, probe, "BYTE_TEST looks swapped, " 2228 "applying WORD_SWAP"); 2229 smsc911x_reg_write(pdata, WORD_SWAP, 0xffffffff); 2230 2231 /* 1 dummy read of BYTE_TEST is needed after a write to 2232 * WORD_SWAP before its contents are valid */ 2233 byte_test = smsc911x_reg_read(pdata, BYTE_TEST); 2234 2235 byte_test = smsc911x_reg_read(pdata, BYTE_TEST); 2236 } 2237 2238 if (byte_test != 0x87654321) { 2239 SMSC_WARN(pdata, drv, "BYTE_TEST: 0x%08X", byte_test); 2240 if (((byte_test >> 16) & 0xFFFF) == (byte_test & 0xFFFF)) { 2241 SMSC_WARN(pdata, probe, 2242 "top 16 bits equal to bottom 16 bits"); 2243 SMSC_TRACE(pdata, probe, 2244 "This may mean the chip is set " 2245 "for 32 bit while the bus is reading 16 bit"); 2246 } 2247 return -ENODEV; 2248 } 2249 2250 /* Default generation to zero (all workarounds apply) */ 2251 pdata->generation = 0; 2252 2253 pdata->idrev = smsc911x_reg_read(pdata, ID_REV); 2254 switch (pdata->idrev & 0xFFFF0000) { 2255 case LAN9118: 2256 case LAN9117: 2257 case LAN9116: 2258 case LAN9115: 2259 case LAN89218: 2260 /* LAN911[5678] family */ 2261 pdata->generation = pdata->idrev & 0x0000FFFF; 2262 break; 2263 2264 case LAN9218: 2265 case LAN9217: 2266 case LAN9216: 2267 case LAN9215: 2268 /* LAN921[5678] family */ 2269 pdata->generation = 3; 2270 break; 2271 2272 case LAN9210: 2273 case LAN9211: 2274 case LAN9220: 2275 case LAN9221: 2276 case LAN9250: 2277 /* LAN9210/LAN9211/LAN9220/LAN9221/LAN9250 */ 2278 pdata->generation = 4; 2279 break; 2280 2281 default: 2282 SMSC_WARN(pdata, probe, "LAN911x not identified, idrev: 0x%08X", 2283 pdata->idrev); 2284 return -ENODEV; 2285 } 2286 2287 SMSC_TRACE(pdata, probe, 2288 "LAN911x identified, idrev: 0x%08X, generation: %d", 2289 pdata->idrev, pdata->generation); 2290 2291 if (pdata->generation == 0) 2292 SMSC_WARN(pdata, probe, 2293 "This driver is not intended for this chip revision"); 2294 2295 /* workaround for platforms without an eeprom, where the mac address 2296 * is stored elsewhere and set by the bootloader. This saves the 2297 * mac address before resetting the device */ 2298 if (pdata->config.flags & SMSC911X_SAVE_MAC_ADDRESS) { 2299 spin_lock_irq(&pdata->mac_lock); 2300 smsc911x_read_mac_address(dev); 2301 spin_unlock_irq(&pdata->mac_lock); 2302 } 2303 2304 /* Reset the LAN911x */ 2305 if (smsc911x_phy_reset(pdata) || smsc911x_soft_reset(pdata)) 2306 return -ENODEV; 2307 2308 dev->flags |= IFF_MULTICAST; 2309 netif_napi_add_weight(dev, &pdata->napi, smsc911x_poll, 2310 SMSC_NAPI_WEIGHT); 2311 dev->netdev_ops = &smsc911x_netdev_ops; 2312 dev->ethtool_ops = &smsc911x_ethtool_ops; 2313 2314 return 0; 2315 } 2316 2317 static int smsc911x_drv_remove(struct platform_device *pdev) 2318 { 2319 struct net_device *dev; 2320 struct smsc911x_data *pdata; 2321 struct resource *res; 2322 2323 dev = platform_get_drvdata(pdev); 2324 BUG_ON(!dev); 2325 pdata = netdev_priv(dev); 2326 BUG_ON(!pdata); 2327 BUG_ON(!pdata->ioaddr); 2328 2329 SMSC_TRACE(pdata, ifdown, "Stopping driver"); 2330 2331 unregister_netdev(dev); 2332 2333 mdiobus_unregister(pdata->mii_bus); 2334 mdiobus_free(pdata->mii_bus); 2335 2336 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, 2337 "smsc911x-memory"); 2338 if (!res) 2339 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 2340 2341 release_mem_region(res->start, resource_size(res)); 2342 2343 iounmap(pdata->ioaddr); 2344 2345 (void)smsc911x_disable_resources(pdev); 2346 smsc911x_free_resources(pdev); 2347 2348 free_netdev(dev); 2349 2350 pm_runtime_disable(&pdev->dev); 2351 2352 return 0; 2353 } 2354 2355 /* standard register acces */ 2356 static const struct smsc911x_ops standard_smsc911x_ops = { 2357 .reg_read = __smsc911x_reg_read, 2358 .reg_write = __smsc911x_reg_write, 2359 .rx_readfifo = smsc911x_rx_readfifo, 2360 .tx_writefifo = smsc911x_tx_writefifo, 2361 }; 2362 2363 /* shifted register access */ 2364 static const struct smsc911x_ops shifted_smsc911x_ops = { 2365 .reg_read = __smsc911x_reg_read_shift, 2366 .reg_write = __smsc911x_reg_write_shift, 2367 .rx_readfifo = smsc911x_rx_readfifo_shift, 2368 .tx_writefifo = smsc911x_tx_writefifo_shift, 2369 }; 2370 2371 static int smsc911x_probe_config(struct smsc911x_platform_config *config, 2372 struct device *dev) 2373 { 2374 int phy_interface; 2375 u32 width = 0; 2376 int err; 2377 2378 phy_interface = device_get_phy_mode(dev); 2379 if (phy_interface < 0) 2380 phy_interface = PHY_INTERFACE_MODE_NA; 2381 config->phy_interface = phy_interface; 2382 2383 device_get_mac_address(dev, config->mac); 2384 2385 err = device_property_read_u32(dev, "reg-io-width", &width); 2386 if (err == -ENXIO) 2387 return err; 2388 if (!err && width == 4) 2389 config->flags |= SMSC911X_USE_32BIT; 2390 else 2391 config->flags |= SMSC911X_USE_16BIT; 2392 2393 device_property_read_u32(dev, "reg-shift", &config->shift); 2394 2395 if (device_property_present(dev, "smsc,irq-active-high")) 2396 config->irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_HIGH; 2397 2398 if (device_property_present(dev, "smsc,irq-push-pull")) 2399 config->irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL; 2400 2401 if (device_property_present(dev, "smsc,force-internal-phy")) 2402 config->flags |= SMSC911X_FORCE_INTERNAL_PHY; 2403 2404 if (device_property_present(dev, "smsc,force-external-phy")) 2405 config->flags |= SMSC911X_FORCE_EXTERNAL_PHY; 2406 2407 if (device_property_present(dev, "smsc,save-mac-address")) 2408 config->flags |= SMSC911X_SAVE_MAC_ADDRESS; 2409 2410 return 0; 2411 } 2412 2413 static int smsc911x_drv_probe(struct platform_device *pdev) 2414 { 2415 struct net_device *dev; 2416 struct smsc911x_data *pdata; 2417 struct smsc911x_platform_config *config = dev_get_platdata(&pdev->dev); 2418 struct resource *res; 2419 int res_size, irq; 2420 int retval; 2421 2422 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, 2423 "smsc911x-memory"); 2424 if (!res) 2425 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 2426 if (!res) { 2427 pr_warn("Could not allocate resource\n"); 2428 retval = -ENODEV; 2429 goto out_0; 2430 } 2431 res_size = resource_size(res); 2432 2433 irq = platform_get_irq(pdev, 0); 2434 if (irq == -EPROBE_DEFER) { 2435 retval = -EPROBE_DEFER; 2436 goto out_0; 2437 } else if (irq < 0) { 2438 pr_warn("Could not allocate irq resource\n"); 2439 retval = -ENODEV; 2440 goto out_0; 2441 } 2442 2443 if (!request_mem_region(res->start, res_size, SMSC_CHIPNAME)) { 2444 retval = -EBUSY; 2445 goto out_0; 2446 } 2447 2448 dev = alloc_etherdev(sizeof(struct smsc911x_data)); 2449 if (!dev) { 2450 retval = -ENOMEM; 2451 goto out_release_io_1; 2452 } 2453 2454 SET_NETDEV_DEV(dev, &pdev->dev); 2455 2456 pdata = netdev_priv(dev); 2457 dev->irq = irq; 2458 pdata->ioaddr = ioremap(res->start, res_size); 2459 if (!pdata->ioaddr) { 2460 retval = -ENOMEM; 2461 goto out_ioremap_fail; 2462 } 2463 2464 pdata->dev = dev; 2465 pdata->msg_enable = ((1 << debug) - 1); 2466 2467 platform_set_drvdata(pdev, dev); 2468 2469 retval = smsc911x_request_resources(pdev); 2470 if (retval) 2471 goto out_request_resources_fail; 2472 2473 retval = smsc911x_enable_resources(pdev); 2474 if (retval) 2475 goto out_enable_resources_fail; 2476 2477 if (pdata->ioaddr == NULL) { 2478 SMSC_WARN(pdata, probe, "Error smsc911x base address invalid"); 2479 retval = -ENOMEM; 2480 goto out_disable_resources; 2481 } 2482 2483 retval = smsc911x_probe_config(&pdata->config, &pdev->dev); 2484 if (retval && config) { 2485 /* copy config parameters across to pdata */ 2486 memcpy(&pdata->config, config, sizeof(pdata->config)); 2487 retval = 0; 2488 } 2489 2490 if (retval) { 2491 SMSC_WARN(pdata, probe, "Error smsc911x config not found"); 2492 goto out_disable_resources; 2493 } 2494 2495 /* assume standard, non-shifted, access to HW registers */ 2496 pdata->ops = &standard_smsc911x_ops; 2497 /* apply the right access if shifting is needed */ 2498 if (pdata->config.shift) 2499 pdata->ops = &shifted_smsc911x_ops; 2500 2501 pm_runtime_enable(&pdev->dev); 2502 pm_runtime_get_sync(&pdev->dev); 2503 2504 retval = smsc911x_init(dev); 2505 if (retval < 0) 2506 goto out_init_fail; 2507 2508 netif_carrier_off(dev); 2509 2510 retval = smsc911x_mii_init(pdev, dev); 2511 if (retval) { 2512 SMSC_WARN(pdata, probe, "Error %i initialising mii", retval); 2513 goto out_init_fail; 2514 } 2515 2516 retval = register_netdev(dev); 2517 if (retval) { 2518 SMSC_WARN(pdata, probe, "Error %i registering device", retval); 2519 goto out_init_fail; 2520 } else { 2521 SMSC_TRACE(pdata, probe, 2522 "Network interface: \"%s\"", dev->name); 2523 } 2524 2525 spin_lock_irq(&pdata->mac_lock); 2526 2527 /* Check if mac address has been specified when bringing interface up */ 2528 if (is_valid_ether_addr(dev->dev_addr)) { 2529 smsc911x_set_hw_mac_address(pdata, dev->dev_addr); 2530 SMSC_TRACE(pdata, probe, 2531 "MAC Address is specified by configuration"); 2532 } else if (is_valid_ether_addr(pdata->config.mac)) { 2533 eth_hw_addr_set(dev, pdata->config.mac); 2534 SMSC_TRACE(pdata, probe, 2535 "MAC Address specified by platform data"); 2536 } else { 2537 /* Try reading mac address from device. if EEPROM is present 2538 * it will already have been set */ 2539 smsc_get_mac(dev); 2540 2541 if (is_valid_ether_addr(dev->dev_addr)) { 2542 /* eeprom values are valid so use them */ 2543 SMSC_TRACE(pdata, probe, 2544 "Mac Address is read from LAN911x EEPROM"); 2545 } else { 2546 /* eeprom values are invalid, generate random MAC */ 2547 eth_hw_addr_random(dev); 2548 smsc911x_set_hw_mac_address(pdata, dev->dev_addr); 2549 SMSC_TRACE(pdata, probe, 2550 "MAC Address is set to eth_random_addr"); 2551 } 2552 } 2553 2554 spin_unlock_irq(&pdata->mac_lock); 2555 pm_runtime_put(&pdev->dev); 2556 2557 netdev_info(dev, "MAC Address: %pM\n", dev->dev_addr); 2558 2559 return 0; 2560 2561 out_init_fail: 2562 pm_runtime_put(&pdev->dev); 2563 pm_runtime_disable(&pdev->dev); 2564 out_disable_resources: 2565 (void)smsc911x_disable_resources(pdev); 2566 out_enable_resources_fail: 2567 smsc911x_free_resources(pdev); 2568 out_request_resources_fail: 2569 iounmap(pdata->ioaddr); 2570 out_ioremap_fail: 2571 free_netdev(dev); 2572 out_release_io_1: 2573 release_mem_region(res->start, resource_size(res)); 2574 out_0: 2575 return retval; 2576 } 2577 2578 #ifdef CONFIG_PM 2579 /* This implementation assumes the devices remains powered on its VDDVARIO 2580 * pins during suspend. */ 2581 2582 /* TODO: implement freeze/thaw callbacks for hibernation.*/ 2583 2584 static int smsc911x_suspend(struct device *dev) 2585 { 2586 struct net_device *ndev = dev_get_drvdata(dev); 2587 struct smsc911x_data *pdata = netdev_priv(ndev); 2588 2589 if (netif_running(ndev)) { 2590 netif_stop_queue(ndev); 2591 netif_device_detach(ndev); 2592 if (!device_may_wakeup(dev)) 2593 phy_stop(ndev->phydev); 2594 } 2595 2596 /* enable wake on LAN, energy detection and the external PME 2597 * signal. */ 2598 smsc911x_reg_write(pdata, PMT_CTRL, 2599 PMT_CTRL_PM_MODE_D1_ | PMT_CTRL_WOL_EN_ | 2600 PMT_CTRL_ED_EN_ | PMT_CTRL_PME_EN_); 2601 2602 pm_runtime_disable(dev); 2603 pm_runtime_set_suspended(dev); 2604 2605 return 0; 2606 } 2607 2608 static int smsc911x_resume(struct device *dev) 2609 { 2610 struct net_device *ndev = dev_get_drvdata(dev); 2611 struct smsc911x_data *pdata = netdev_priv(ndev); 2612 unsigned int to = 100; 2613 2614 pm_runtime_enable(dev); 2615 pm_runtime_resume(dev); 2616 2617 /* Note 3.11 from the datasheet: 2618 * "When the LAN9220 is in a power saving state, a write of any 2619 * data to the BYTE_TEST register will wake-up the device." 2620 */ 2621 smsc911x_reg_write(pdata, BYTE_TEST, 0); 2622 2623 /* poll the READY bit in PMT_CTRL. Any other access to the device is 2624 * forbidden while this bit isn't set. Try for 100ms and return -EIO 2625 * if it failed. */ 2626 while (!(smsc911x_reg_read(pdata, PMT_CTRL) & PMT_CTRL_READY_) && --to) 2627 udelay(1000); 2628 2629 if (to == 0) 2630 return -EIO; 2631 2632 if (netif_running(ndev)) { 2633 netif_device_attach(ndev); 2634 netif_start_queue(ndev); 2635 if (!device_may_wakeup(dev)) 2636 phy_start(ndev->phydev); 2637 } 2638 2639 return 0; 2640 } 2641 2642 static const struct dev_pm_ops smsc911x_pm_ops = { 2643 .suspend = smsc911x_suspend, 2644 .resume = smsc911x_resume, 2645 }; 2646 2647 #define SMSC911X_PM_OPS (&smsc911x_pm_ops) 2648 2649 #else 2650 #define SMSC911X_PM_OPS NULL 2651 #endif 2652 2653 #ifdef CONFIG_OF 2654 static const struct of_device_id smsc911x_dt_ids[] = { 2655 { .compatible = "smsc,lan9115", }, 2656 { /* sentinel */ } 2657 }; 2658 MODULE_DEVICE_TABLE(of, smsc911x_dt_ids); 2659 #endif 2660 2661 #ifdef CONFIG_ACPI 2662 static const struct acpi_device_id smsc911x_acpi_match[] = { 2663 { "ARMH9118", 0 }, 2664 { } 2665 }; 2666 MODULE_DEVICE_TABLE(acpi, smsc911x_acpi_match); 2667 #endif 2668 2669 static struct platform_driver smsc911x_driver = { 2670 .probe = smsc911x_drv_probe, 2671 .remove = smsc911x_drv_remove, 2672 .driver = { 2673 .name = SMSC_CHIPNAME, 2674 .pm = SMSC911X_PM_OPS, 2675 .of_match_table = of_match_ptr(smsc911x_dt_ids), 2676 .acpi_match_table = ACPI_PTR(smsc911x_acpi_match), 2677 }, 2678 }; 2679 2680 /* Entry point for loading the module */ 2681 static int __init smsc911x_init_module(void) 2682 { 2683 SMSC_INITIALIZE(); 2684 return platform_driver_register(&smsc911x_driver); 2685 } 2686 2687 /* entry point for unloading the module */ 2688 static void __exit smsc911x_cleanup_module(void) 2689 { 2690 platform_driver_unregister(&smsc911x_driver); 2691 } 2692 2693 module_init(smsc911x_init_module); 2694 module_exit(smsc911x_cleanup_module); 2695