1 /* SPDX-License-Identifier: GPL-2.0 */ 2 /* Linux header file for the ATP pocket ethernet adapter. */ 3 /* v1.09 8/9/2000 becker@scyld.com. */ 4 5 #include <linux/if_ether.h> 6 #include <linux/types.h> 7 8 /* The header prepended to received packets. */ 9 struct rx_header { 10 ushort pad; /* Pad. */ 11 ushort rx_count; 12 ushort rx_status; /* Unknown bit assignments :-<. */ 13 ushort cur_addr; /* Apparently the current buffer address(?) */ 14 }; 15 16 #define PAR_DATA 0 17 #define PAR_STATUS 1 18 #define PAR_CONTROL 2 19 20 #define Ctrl_LNibRead 0x08 /* LP_PSELECP */ 21 #define Ctrl_HNibRead 0 22 #define Ctrl_LNibWrite 0x08 /* LP_PSELECP */ 23 #define Ctrl_HNibWrite 0 24 #define Ctrl_SelData 0x04 /* LP_PINITP */ 25 #define Ctrl_IRQEN 0x10 /* LP_PINTEN */ 26 27 #define EOW 0xE0 28 #define EOC 0xE0 29 #define WrAddr 0x40 /* Set address of EPLC read, write register. */ 30 #define RdAddr 0xC0 31 #define HNib 0x10 32 33 enum page0_regs { 34 /* The first six registers hold 35 * the ethernet physical station address. 36 */ 37 PAR0 = 0, PAR1 = 1, PAR2 = 2, PAR3 = 3, PAR4 = 4, PAR5 = 5, 38 TxCNT0 = 6, TxCNT1 = 7, /* The transmit byte count. */ 39 TxSTAT = 8, RxSTAT = 9, /* Tx and Rx status. */ 40 ISR = 10, IMR = 11, /* Interrupt status and mask. */ 41 CMR1 = 12, /* Command register 1. */ 42 CMR2 = 13, /* Command register 2. */ 43 MODSEL = 14, /* Mode select register. */ 44 MAR = 14, /* Memory address register (?). */ 45 CMR2_h = 0x1d, 46 }; 47 48 enum eepage_regs { 49 PROM_CMD = 6, 50 PROM_DATA = 7 /* Note that PROM_CMD is in the "high" bits. */ 51 }; 52 53 #define ISR_TxOK 0x01 54 #define ISR_RxOK 0x04 55 #define ISR_TxErr 0x02 56 #define ISRh_RxErr 0x11 /* ISR, high nibble */ 57 58 #define CMR1h_MUX 0x08 /* Select printer multiplexor on 8012. */ 59 #define CMR1h_RESET 0x04 /* Reset. */ 60 #define CMR1h_RxENABLE 0x02 /* Rx unit enable. */ 61 #define CMR1h_TxENABLE 0x01 /* Tx unit enable. */ 62 #define CMR1h_TxRxOFF 0x00 63 #define CMR1_ReXmit 0x08 /* Trigger a retransmit. */ 64 #define CMR1_Xmit 0x04 /* Trigger a transmit. */ 65 #define CMR1_IRQ 0x02 /* Interrupt active. */ 66 #define CMR1_BufEnb 0x01 /* Enable the buffer(?). */ 67 #define CMR1_NextPkt 0x01 /* Enable the buffer(?). */ 68 69 #define CMR2_NULL 8 70 #define CMR2_IRQOUT 9 71 #define CMR2_RAMTEST 10 72 #define CMR2_EEPROM 12 /* Set to page 1, for reading the EEPROM. */ 73 74 #define CMR2h_OFF 0 /* No accept mode. */ 75 #define CMR2h_Physical 1 /* Accept a physical address match only. */ 76 #define CMR2h_Normal 2 /* Accept physical and broadcast address. */ 77 #define CMR2h_PROMISC 3 /* Promiscuous mode. */ 78 79 /* An inline function used below: it differs from inb() by explicitly 80 * return an unsigned char, saving a truncation. 81 */ 82 static inline unsigned char inbyte(unsigned short port) 83 { 84 unsigned char _v; 85 86 __asm__ __volatile__ ("inb %w1,%b0" : "=a" (_v) : "d" (port)); 87 return _v; 88 } 89 90 /* Read register OFFSET. 91 * This command should always be terminated with read_end(). 92 */ 93 static inline unsigned char read_nibble(short port, unsigned char offset) 94 { 95 unsigned char retval; 96 97 outb(EOC+offset, port + PAR_DATA); 98 outb(RdAddr+offset, port + PAR_DATA); 99 inbyte(port + PAR_STATUS); /* Settling time delay */ 100 retval = inbyte(port + PAR_STATUS); 101 outb(EOC+offset, port + PAR_DATA); 102 103 return retval; 104 } 105 106 /* Functions for bulk data read. The interrupt line is always disabled. */ 107 /* Get a byte using read mode 0, reading data from the control lines. */ 108 static inline unsigned char read_byte_mode0(short ioaddr) 109 { 110 unsigned char low_nib; 111 112 outb(Ctrl_LNibRead, ioaddr + PAR_CONTROL); 113 inbyte(ioaddr + PAR_STATUS); 114 low_nib = (inbyte(ioaddr + PAR_STATUS) >> 3) & 0x0f; 115 outb(Ctrl_HNibRead, ioaddr + PAR_CONTROL); 116 inbyte(ioaddr + PAR_STATUS); /* Settling time delay -- needed! */ 117 inbyte(ioaddr + PAR_STATUS); /* Settling time delay -- needed! */ 118 return low_nib | ((inbyte(ioaddr + PAR_STATUS) << 1) & 0xf0); 119 } 120 121 /* The same as read_byte_mode0(), but does multiple inb()s for stability. */ 122 static inline unsigned char read_byte_mode2(short ioaddr) 123 { 124 unsigned char low_nib; 125 126 outb(Ctrl_LNibRead, ioaddr + PAR_CONTROL); 127 inbyte(ioaddr + PAR_STATUS); 128 low_nib = (inbyte(ioaddr + PAR_STATUS) >> 3) & 0x0f; 129 outb(Ctrl_HNibRead, ioaddr + PAR_CONTROL); 130 inbyte(ioaddr + PAR_STATUS); /* Settling time delay -- needed! */ 131 return low_nib | ((inbyte(ioaddr + PAR_STATUS) << 1) & 0xf0); 132 } 133 134 /* Read a byte through the data register. */ 135 static inline unsigned char read_byte_mode4(short ioaddr) 136 { 137 unsigned char low_nib; 138 139 outb(RdAddr | MAR, ioaddr + PAR_DATA); 140 low_nib = (inbyte(ioaddr + PAR_STATUS) >> 3) & 0x0f; 141 outb(RdAddr | HNib | MAR, ioaddr + PAR_DATA); 142 return low_nib | ((inbyte(ioaddr + PAR_STATUS) << 1) & 0xf0); 143 } 144 145 /* Read a byte through the data register, double reading to allow settling. */ 146 static inline unsigned char read_byte_mode6(short ioaddr) 147 { 148 unsigned char low_nib; 149 150 outb(RdAddr | MAR, ioaddr + PAR_DATA); 151 inbyte(ioaddr + PAR_STATUS); 152 low_nib = (inbyte(ioaddr + PAR_STATUS) >> 3) & 0x0f; 153 outb(RdAddr | HNib | MAR, ioaddr + PAR_DATA); 154 inbyte(ioaddr + PAR_STATUS); 155 return low_nib | ((inbyte(ioaddr + PAR_STATUS) << 1) & 0xf0); 156 } 157 158 static inline void 159 write_reg(short port, unsigned char reg, unsigned char value) 160 { 161 unsigned char outval; 162 163 outb(EOC | reg, port + PAR_DATA); 164 outval = WrAddr | reg; 165 outb(outval, port + PAR_DATA); 166 outb(outval, port + PAR_DATA); /* Double write for PS/2. */ 167 168 outval &= 0xf0; 169 outval |= value; 170 outb(outval, port + PAR_DATA); 171 outval &= 0x1f; 172 outb(outval, port + PAR_DATA); 173 outb(outval, port + PAR_DATA); 174 175 outb(EOC | outval, port + PAR_DATA); 176 } 177 178 static inline void 179 write_reg_high(short port, unsigned char reg, unsigned char value) 180 { 181 unsigned char outval = EOC | HNib | reg; 182 183 outb(outval, port + PAR_DATA); 184 outval &= WrAddr | HNib | 0x0f; 185 outb(outval, port + PAR_DATA); 186 outb(outval, port + PAR_DATA); /* Double write for PS/2. */ 187 188 outval = WrAddr | HNib | value; 189 outb(outval, port + PAR_DATA); 190 outval &= HNib | 0x0f; /* HNib | value */ 191 outb(outval, port + PAR_DATA); 192 outb(outval, port + PAR_DATA); 193 194 outb(EOC | HNib | outval, port + PAR_DATA); 195 } 196 197 /* Write a byte out using nibble mode. The low nibble is written first. */ 198 static inline void 199 write_reg_byte(short port, unsigned char reg, unsigned char value) 200 { 201 unsigned char outval; 202 203 outb(EOC | reg, port + PAR_DATA); /* Reset the address register. */ 204 outval = WrAddr | reg; 205 outb(outval, port + PAR_DATA); 206 outb(outval, port + PAR_DATA); /* Double write for PS/2. */ 207 208 outb((outval & 0xf0) | (value & 0x0f), port + PAR_DATA); 209 outb(value & 0x0f, port + PAR_DATA); 210 value >>= 4; 211 outb(value, port + PAR_DATA); 212 outb(0x10 | value, port + PAR_DATA); 213 outb(0x10 | value, port + PAR_DATA); 214 215 outb(EOC | value, port + PAR_DATA); /* Reset the address register. */ 216 } 217 218 /* Bulk data writes to the packet buffer. The interrupt line remains enabled. 219 * The first, faster method uses only the dataport (data modes 0, 2 & 4). 220 * The second (backup) method uses data and control regs (modes 1, 3 & 5). 221 * It should only be needed when there is skew between the individual data 222 * lines. 223 */ 224 static inline void write_byte_mode0(short ioaddr, unsigned char value) 225 { 226 outb(value & 0x0f, ioaddr + PAR_DATA); 227 outb((value>>4) | 0x10, ioaddr + PAR_DATA); 228 } 229 230 static inline void write_byte_mode1(short ioaddr, unsigned char value) 231 { 232 outb(value & 0x0f, ioaddr + PAR_DATA); 233 outb(Ctrl_IRQEN | Ctrl_LNibWrite, ioaddr + PAR_CONTROL); 234 outb((value>>4) | 0x10, ioaddr + PAR_DATA); 235 outb(Ctrl_IRQEN | Ctrl_HNibWrite, ioaddr + PAR_CONTROL); 236 } 237 238 /* Write 16bit VALUE to the packet buffer: the same as above just doubled. */ 239 static inline void write_word_mode0(short ioaddr, unsigned short value) 240 { 241 outb(value & 0x0f, ioaddr + PAR_DATA); 242 value >>= 4; 243 outb((value & 0x0f) | 0x10, ioaddr + PAR_DATA); 244 value >>= 4; 245 outb(value & 0x0f, ioaddr + PAR_DATA); 246 value >>= 4; 247 outb((value & 0x0f) | 0x10, ioaddr + PAR_DATA); 248 } 249 250 /* EEPROM_Ctrl bits. */ 251 #define EE_SHIFT_CLK 0x04 /* EEPROM shift clock. */ 252 #define EE_CS 0x02 /* EEPROM chip select. */ 253 #define EE_CLK_HIGH 0x12 254 #define EE_CLK_LOW 0x16 255 #define EE_DATA_WRITE 0x01 /* EEPROM chip data in. */ 256 #define EE_DATA_READ 0x08 /* EEPROM chip data out. */ 257 258 /* Delay between EEPROM clock transitions. */ 259 #define eeprom_delay(ticks) \ 260 do { int _i = 40; while (--_i > 0) { __SLOW_DOWN_IO; } } while (0) 261 262 /* The EEPROM commands include the alway-set leading bit. */ 263 #define EE_WRITE_CMD(offset) (((5 << 6) + (offset)) << 17) 264 #define EE_READ(offset) (((6 << 6) + (offset)) << 17) 265 #define EE_ERASE(offset) (((7 << 6) + (offset)) << 17) 266 #define EE_CMD_SIZE 27 /* The command+address+data size. */ 267