1 // SPDX-License-Identifier: GPL-2.0 2 /* Copyright(c) 1999 - 2018 Intel Corporation. */ 3 4 #include <linux/pci.h> 5 #include <linux/delay.h> 6 #include <linux/iopoll.h> 7 #include <linux/sched.h> 8 9 #include "ixgbe.h" 10 #include "ixgbe_phy.h" 11 12 static void ixgbe_i2c_start(struct ixgbe_hw *hw); 13 static void ixgbe_i2c_stop(struct ixgbe_hw *hw); 14 static s32 ixgbe_clock_in_i2c_byte(struct ixgbe_hw *hw, u8 *data); 15 static s32 ixgbe_clock_out_i2c_byte(struct ixgbe_hw *hw, u8 data); 16 static s32 ixgbe_get_i2c_ack(struct ixgbe_hw *hw); 17 static s32 ixgbe_clock_in_i2c_bit(struct ixgbe_hw *hw, bool *data); 18 static s32 ixgbe_clock_out_i2c_bit(struct ixgbe_hw *hw, bool data); 19 static void ixgbe_raise_i2c_clk(struct ixgbe_hw *hw, u32 *i2cctl); 20 static void ixgbe_lower_i2c_clk(struct ixgbe_hw *hw, u32 *i2cctl); 21 static s32 ixgbe_set_i2c_data(struct ixgbe_hw *hw, u32 *i2cctl, bool data); 22 static bool ixgbe_get_i2c_data(struct ixgbe_hw *hw, u32 *i2cctl); 23 static void ixgbe_i2c_bus_clear(struct ixgbe_hw *hw); 24 static enum ixgbe_phy_type ixgbe_get_phy_type_from_id(u32 phy_id); 25 static s32 ixgbe_get_phy_id(struct ixgbe_hw *hw); 26 static s32 ixgbe_identify_qsfp_module_generic(struct ixgbe_hw *hw); 27 28 /** 29 * ixgbe_out_i2c_byte_ack - Send I2C byte with ack 30 * @hw: pointer to the hardware structure 31 * @byte: byte to send 32 * 33 * Returns an error code on error. 34 **/ 35 static s32 ixgbe_out_i2c_byte_ack(struct ixgbe_hw *hw, u8 byte) 36 { 37 s32 status; 38 39 status = ixgbe_clock_out_i2c_byte(hw, byte); 40 if (status) 41 return status; 42 return ixgbe_get_i2c_ack(hw); 43 } 44 45 /** 46 * ixgbe_in_i2c_byte_ack - Receive an I2C byte and send ack 47 * @hw: pointer to the hardware structure 48 * @byte: pointer to a u8 to receive the byte 49 * 50 * Returns an error code on error. 51 **/ 52 static s32 ixgbe_in_i2c_byte_ack(struct ixgbe_hw *hw, u8 *byte) 53 { 54 s32 status; 55 56 status = ixgbe_clock_in_i2c_byte(hw, byte); 57 if (status) 58 return status; 59 /* ACK */ 60 return ixgbe_clock_out_i2c_bit(hw, false); 61 } 62 63 /** 64 * ixgbe_ones_comp_byte_add - Perform one's complement addition 65 * @add1: addend 1 66 * @add2: addend 2 67 * 68 * Returns one's complement 8-bit sum. 69 **/ 70 static u8 ixgbe_ones_comp_byte_add(u8 add1, u8 add2) 71 { 72 u16 sum = add1 + add2; 73 74 sum = (sum & 0xFF) + (sum >> 8); 75 return sum & 0xFF; 76 } 77 78 /** 79 * ixgbe_read_i2c_combined_generic_int - Perform I2C read combined operation 80 * @hw: pointer to the hardware structure 81 * @addr: I2C bus address to read from 82 * @reg: I2C device register to read from 83 * @val: pointer to location to receive read value 84 * @lock: true if to take and release semaphore 85 * 86 * Returns an error code on error. 87 */ 88 s32 ixgbe_read_i2c_combined_generic_int(struct ixgbe_hw *hw, u8 addr, 89 u16 reg, u16 *val, bool lock) 90 { 91 u32 swfw_mask = hw->phy.phy_semaphore_mask; 92 int max_retry = 3; 93 int retry = 0; 94 u8 csum_byte; 95 u8 high_bits; 96 u8 low_bits; 97 u8 reg_high; 98 u8 csum; 99 100 reg_high = ((reg >> 7) & 0xFE) | 1; /* Indicate read combined */ 101 csum = ixgbe_ones_comp_byte_add(reg_high, reg & 0xFF); 102 csum = ~csum; 103 do { 104 if (lock && hw->mac.ops.acquire_swfw_sync(hw, swfw_mask)) 105 return IXGBE_ERR_SWFW_SYNC; 106 ixgbe_i2c_start(hw); 107 /* Device Address and write indication */ 108 if (ixgbe_out_i2c_byte_ack(hw, addr)) 109 goto fail; 110 /* Write bits 14:8 */ 111 if (ixgbe_out_i2c_byte_ack(hw, reg_high)) 112 goto fail; 113 /* Write bits 7:0 */ 114 if (ixgbe_out_i2c_byte_ack(hw, reg & 0xFF)) 115 goto fail; 116 /* Write csum */ 117 if (ixgbe_out_i2c_byte_ack(hw, csum)) 118 goto fail; 119 /* Re-start condition */ 120 ixgbe_i2c_start(hw); 121 /* Device Address and read indication */ 122 if (ixgbe_out_i2c_byte_ack(hw, addr | 1)) 123 goto fail; 124 /* Get upper bits */ 125 if (ixgbe_in_i2c_byte_ack(hw, &high_bits)) 126 goto fail; 127 /* Get low bits */ 128 if (ixgbe_in_i2c_byte_ack(hw, &low_bits)) 129 goto fail; 130 /* Get csum */ 131 if (ixgbe_clock_in_i2c_byte(hw, &csum_byte)) 132 goto fail; 133 /* NACK */ 134 if (ixgbe_clock_out_i2c_bit(hw, false)) 135 goto fail; 136 ixgbe_i2c_stop(hw); 137 if (lock) 138 hw->mac.ops.release_swfw_sync(hw, swfw_mask); 139 *val = (high_bits << 8) | low_bits; 140 return 0; 141 142 fail: 143 ixgbe_i2c_bus_clear(hw); 144 if (lock) 145 hw->mac.ops.release_swfw_sync(hw, swfw_mask); 146 retry++; 147 if (retry < max_retry) 148 hw_dbg(hw, "I2C byte read combined error - Retry.\n"); 149 else 150 hw_dbg(hw, "I2C byte read combined error.\n"); 151 } while (retry < max_retry); 152 153 return IXGBE_ERR_I2C; 154 } 155 156 /** 157 * ixgbe_write_i2c_combined_generic_int - Perform I2C write combined operation 158 * @hw: pointer to the hardware structure 159 * @addr: I2C bus address to write to 160 * @reg: I2C device register to write to 161 * @val: value to write 162 * @lock: true if to take and release semaphore 163 * 164 * Returns an error code on error. 165 */ 166 s32 ixgbe_write_i2c_combined_generic_int(struct ixgbe_hw *hw, u8 addr, 167 u16 reg, u16 val, bool lock) 168 { 169 u32 swfw_mask = hw->phy.phy_semaphore_mask; 170 int max_retry = 1; 171 int retry = 0; 172 u8 reg_high; 173 u8 csum; 174 175 reg_high = (reg >> 7) & 0xFE; /* Indicate write combined */ 176 csum = ixgbe_ones_comp_byte_add(reg_high, reg & 0xFF); 177 csum = ixgbe_ones_comp_byte_add(csum, val >> 8); 178 csum = ixgbe_ones_comp_byte_add(csum, val & 0xFF); 179 csum = ~csum; 180 do { 181 if (lock && hw->mac.ops.acquire_swfw_sync(hw, swfw_mask)) 182 return IXGBE_ERR_SWFW_SYNC; 183 ixgbe_i2c_start(hw); 184 /* Device Address and write indication */ 185 if (ixgbe_out_i2c_byte_ack(hw, addr)) 186 goto fail; 187 /* Write bits 14:8 */ 188 if (ixgbe_out_i2c_byte_ack(hw, reg_high)) 189 goto fail; 190 /* Write bits 7:0 */ 191 if (ixgbe_out_i2c_byte_ack(hw, reg & 0xFF)) 192 goto fail; 193 /* Write data 15:8 */ 194 if (ixgbe_out_i2c_byte_ack(hw, val >> 8)) 195 goto fail; 196 /* Write data 7:0 */ 197 if (ixgbe_out_i2c_byte_ack(hw, val & 0xFF)) 198 goto fail; 199 /* Write csum */ 200 if (ixgbe_out_i2c_byte_ack(hw, csum)) 201 goto fail; 202 ixgbe_i2c_stop(hw); 203 if (lock) 204 hw->mac.ops.release_swfw_sync(hw, swfw_mask); 205 return 0; 206 207 fail: 208 ixgbe_i2c_bus_clear(hw); 209 if (lock) 210 hw->mac.ops.release_swfw_sync(hw, swfw_mask); 211 retry++; 212 if (retry < max_retry) 213 hw_dbg(hw, "I2C byte write combined error - Retry.\n"); 214 else 215 hw_dbg(hw, "I2C byte write combined error.\n"); 216 } while (retry < max_retry); 217 218 return IXGBE_ERR_I2C; 219 } 220 221 /** 222 * ixgbe_probe_phy - Probe a single address for a PHY 223 * @hw: pointer to hardware structure 224 * @phy_addr: PHY address to probe 225 * 226 * Returns true if PHY found 227 **/ 228 static bool ixgbe_probe_phy(struct ixgbe_hw *hw, u16 phy_addr) 229 { 230 u16 ext_ability = 0; 231 232 hw->phy.mdio.prtad = phy_addr; 233 if (mdio45_probe(&hw->phy.mdio, phy_addr) != 0) 234 return false; 235 236 if (ixgbe_get_phy_id(hw)) 237 return false; 238 239 hw->phy.type = ixgbe_get_phy_type_from_id(hw->phy.id); 240 241 if (hw->phy.type == ixgbe_phy_unknown) { 242 hw->phy.ops.read_reg(hw, 243 MDIO_PMA_EXTABLE, 244 MDIO_MMD_PMAPMD, 245 &ext_ability); 246 if (ext_ability & 247 (MDIO_PMA_EXTABLE_10GBT | 248 MDIO_PMA_EXTABLE_1000BT)) 249 hw->phy.type = ixgbe_phy_cu_unknown; 250 else 251 hw->phy.type = ixgbe_phy_generic; 252 } 253 254 return true; 255 } 256 257 /** 258 * ixgbe_identify_phy_generic - Get physical layer module 259 * @hw: pointer to hardware structure 260 * 261 * Determines the physical layer module found on the current adapter. 262 **/ 263 s32 ixgbe_identify_phy_generic(struct ixgbe_hw *hw) 264 { 265 u32 phy_addr; 266 u32 status = IXGBE_ERR_PHY_ADDR_INVALID; 267 268 if (!hw->phy.phy_semaphore_mask) { 269 if (hw->bus.lan_id) 270 hw->phy.phy_semaphore_mask = IXGBE_GSSR_PHY1_SM; 271 else 272 hw->phy.phy_semaphore_mask = IXGBE_GSSR_PHY0_SM; 273 } 274 275 if (hw->phy.type != ixgbe_phy_unknown) 276 return 0; 277 278 if (hw->phy.nw_mng_if_sel) { 279 phy_addr = (hw->phy.nw_mng_if_sel & 280 IXGBE_NW_MNG_IF_SEL_MDIO_PHY_ADD) >> 281 IXGBE_NW_MNG_IF_SEL_MDIO_PHY_ADD_SHIFT; 282 if (ixgbe_probe_phy(hw, phy_addr)) 283 return 0; 284 else 285 return IXGBE_ERR_PHY_ADDR_INVALID; 286 } 287 288 for (phy_addr = 0; phy_addr < IXGBE_MAX_PHY_ADDR; phy_addr++) { 289 if (ixgbe_probe_phy(hw, phy_addr)) { 290 status = 0; 291 break; 292 } 293 } 294 295 /* Certain media types do not have a phy so an address will not 296 * be found and the code will take this path. Caller has to 297 * decide if it is an error or not. 298 */ 299 if (status) 300 hw->phy.mdio.prtad = MDIO_PRTAD_NONE; 301 302 return status; 303 } 304 305 /** 306 * ixgbe_check_reset_blocked - check status of MNG FW veto bit 307 * @hw: pointer to the hardware structure 308 * 309 * This function checks the MMNGC.MNG_VETO bit to see if there are 310 * any constraints on link from manageability. For MAC's that don't 311 * have this bit just return false since the link can not be blocked 312 * via this method. 313 **/ 314 bool ixgbe_check_reset_blocked(struct ixgbe_hw *hw) 315 { 316 u32 mmngc; 317 318 /* If we don't have this bit, it can't be blocking */ 319 if (hw->mac.type == ixgbe_mac_82598EB) 320 return false; 321 322 mmngc = IXGBE_READ_REG(hw, IXGBE_MMNGC); 323 if (mmngc & IXGBE_MMNGC_MNG_VETO) { 324 hw_dbg(hw, "MNG_VETO bit detected.\n"); 325 return true; 326 } 327 328 return false; 329 } 330 331 /** 332 * ixgbe_get_phy_id - Get the phy type 333 * @hw: pointer to hardware structure 334 * 335 **/ 336 static s32 ixgbe_get_phy_id(struct ixgbe_hw *hw) 337 { 338 s32 status; 339 u16 phy_id_high = 0; 340 u16 phy_id_low = 0; 341 342 status = hw->phy.ops.read_reg(hw, MDIO_DEVID1, MDIO_MMD_PMAPMD, 343 &phy_id_high); 344 345 if (!status) { 346 hw->phy.id = (u32)(phy_id_high << 16); 347 status = hw->phy.ops.read_reg(hw, MDIO_DEVID2, MDIO_MMD_PMAPMD, 348 &phy_id_low); 349 hw->phy.id |= (u32)(phy_id_low & IXGBE_PHY_REVISION_MASK); 350 hw->phy.revision = (u32)(phy_id_low & ~IXGBE_PHY_REVISION_MASK); 351 } 352 return status; 353 } 354 355 /** 356 * ixgbe_get_phy_type_from_id - Get the phy type 357 * @phy_id: hardware phy id 358 * 359 **/ 360 static enum ixgbe_phy_type ixgbe_get_phy_type_from_id(u32 phy_id) 361 { 362 enum ixgbe_phy_type phy_type; 363 364 switch (phy_id) { 365 case TN1010_PHY_ID: 366 phy_type = ixgbe_phy_tn; 367 break; 368 case X550_PHY_ID2: 369 case X550_PHY_ID3: 370 case X540_PHY_ID: 371 phy_type = ixgbe_phy_aq; 372 break; 373 case QT2022_PHY_ID: 374 phy_type = ixgbe_phy_qt; 375 break; 376 case ATH_PHY_ID: 377 phy_type = ixgbe_phy_nl; 378 break; 379 case X557_PHY_ID: 380 case X557_PHY_ID2: 381 phy_type = ixgbe_phy_x550em_ext_t; 382 break; 383 case BCM54616S_E_PHY_ID: 384 phy_type = ixgbe_phy_ext_1g_t; 385 break; 386 default: 387 phy_type = ixgbe_phy_unknown; 388 break; 389 } 390 391 return phy_type; 392 } 393 394 /** 395 * ixgbe_reset_phy_generic - Performs a PHY reset 396 * @hw: pointer to hardware structure 397 **/ 398 s32 ixgbe_reset_phy_generic(struct ixgbe_hw *hw) 399 { 400 u32 i; 401 u16 ctrl = 0; 402 s32 status = 0; 403 404 if (hw->phy.type == ixgbe_phy_unknown) 405 status = ixgbe_identify_phy_generic(hw); 406 407 if (status != 0 || hw->phy.type == ixgbe_phy_none) 408 return status; 409 410 /* Don't reset PHY if it's shut down due to overtemp. */ 411 if (!hw->phy.reset_if_overtemp && 412 (IXGBE_ERR_OVERTEMP == hw->phy.ops.check_overtemp(hw))) 413 return 0; 414 415 /* Blocked by MNG FW so bail */ 416 if (ixgbe_check_reset_blocked(hw)) 417 return 0; 418 419 /* 420 * Perform soft PHY reset to the PHY_XS. 421 * This will cause a soft reset to the PHY 422 */ 423 hw->phy.ops.write_reg(hw, MDIO_CTRL1, 424 MDIO_MMD_PHYXS, 425 MDIO_CTRL1_RESET); 426 427 /* 428 * Poll for reset bit to self-clear indicating reset is complete. 429 * Some PHYs could take up to 3 seconds to complete and need about 430 * 1.7 usec delay after the reset is complete. 431 */ 432 for (i = 0; i < 30; i++) { 433 msleep(100); 434 if (hw->phy.type == ixgbe_phy_x550em_ext_t) { 435 status = hw->phy.ops.read_reg(hw, 436 IXGBE_MDIO_TX_VENDOR_ALARMS_3, 437 MDIO_MMD_PMAPMD, &ctrl); 438 if (status) 439 return status; 440 441 if (ctrl & IXGBE_MDIO_TX_VENDOR_ALARMS_3_RST_MASK) { 442 udelay(2); 443 break; 444 } 445 } else { 446 status = hw->phy.ops.read_reg(hw, MDIO_CTRL1, 447 MDIO_MMD_PHYXS, &ctrl); 448 if (status) 449 return status; 450 451 if (!(ctrl & MDIO_CTRL1_RESET)) { 452 udelay(2); 453 break; 454 } 455 } 456 } 457 458 if (ctrl & MDIO_CTRL1_RESET) { 459 hw_dbg(hw, "PHY reset polling failed to complete.\n"); 460 return IXGBE_ERR_RESET_FAILED; 461 } 462 463 return 0; 464 } 465 466 /** 467 * ixgbe_read_phy_reg_mdi - read PHY register 468 * @hw: pointer to hardware structure 469 * @reg_addr: 32 bit address of PHY register to read 470 * @device_type: 5 bit device type 471 * @phy_data: Pointer to read data from PHY register 472 * 473 * Reads a value from a specified PHY register without the SWFW lock 474 **/ 475 s32 ixgbe_read_phy_reg_mdi(struct ixgbe_hw *hw, u32 reg_addr, u32 device_type, 476 u16 *phy_data) 477 { 478 u32 i, data, command; 479 480 /* Setup and write the address cycle command */ 481 command = ((reg_addr << IXGBE_MSCA_NP_ADDR_SHIFT) | 482 (device_type << IXGBE_MSCA_DEV_TYPE_SHIFT) | 483 (hw->phy.mdio.prtad << IXGBE_MSCA_PHY_ADDR_SHIFT) | 484 (IXGBE_MSCA_ADDR_CYCLE | IXGBE_MSCA_MDI_COMMAND)); 485 486 IXGBE_WRITE_REG(hw, IXGBE_MSCA, command); 487 488 /* Check every 10 usec to see if the address cycle completed. 489 * The MDI Command bit will clear when the operation is 490 * complete 491 */ 492 for (i = 0; i < IXGBE_MDIO_COMMAND_TIMEOUT; i++) { 493 udelay(10); 494 495 command = IXGBE_READ_REG(hw, IXGBE_MSCA); 496 if ((command & IXGBE_MSCA_MDI_COMMAND) == 0) 497 break; 498 } 499 500 501 if ((command & IXGBE_MSCA_MDI_COMMAND) != 0) { 502 hw_dbg(hw, "PHY address command did not complete.\n"); 503 return IXGBE_ERR_PHY; 504 } 505 506 /* Address cycle complete, setup and write the read 507 * command 508 */ 509 command = ((reg_addr << IXGBE_MSCA_NP_ADDR_SHIFT) | 510 (device_type << IXGBE_MSCA_DEV_TYPE_SHIFT) | 511 (hw->phy.mdio.prtad << IXGBE_MSCA_PHY_ADDR_SHIFT) | 512 (IXGBE_MSCA_READ | IXGBE_MSCA_MDI_COMMAND)); 513 514 IXGBE_WRITE_REG(hw, IXGBE_MSCA, command); 515 516 /* Check every 10 usec to see if the address cycle 517 * completed. The MDI Command bit will clear when the 518 * operation is complete 519 */ 520 for (i = 0; i < IXGBE_MDIO_COMMAND_TIMEOUT; i++) { 521 udelay(10); 522 523 command = IXGBE_READ_REG(hw, IXGBE_MSCA); 524 if ((command & IXGBE_MSCA_MDI_COMMAND) == 0) 525 break; 526 } 527 528 if ((command & IXGBE_MSCA_MDI_COMMAND) != 0) { 529 hw_dbg(hw, "PHY read command didn't complete\n"); 530 return IXGBE_ERR_PHY; 531 } 532 533 /* Read operation is complete. Get the data 534 * from MSRWD 535 */ 536 data = IXGBE_READ_REG(hw, IXGBE_MSRWD); 537 data >>= IXGBE_MSRWD_READ_DATA_SHIFT; 538 *phy_data = (u16)(data); 539 540 return 0; 541 } 542 543 /** 544 * ixgbe_read_phy_reg_generic - Reads a value from a specified PHY register 545 * using the SWFW lock - this function is needed in most cases 546 * @hw: pointer to hardware structure 547 * @reg_addr: 32 bit address of PHY register to read 548 * @device_type: 5 bit device type 549 * @phy_data: Pointer to read data from PHY register 550 **/ 551 s32 ixgbe_read_phy_reg_generic(struct ixgbe_hw *hw, u32 reg_addr, 552 u32 device_type, u16 *phy_data) 553 { 554 s32 status; 555 u32 gssr = hw->phy.phy_semaphore_mask; 556 557 if (hw->mac.ops.acquire_swfw_sync(hw, gssr) == 0) { 558 status = ixgbe_read_phy_reg_mdi(hw, reg_addr, device_type, 559 phy_data); 560 hw->mac.ops.release_swfw_sync(hw, gssr); 561 } else { 562 return IXGBE_ERR_SWFW_SYNC; 563 } 564 565 return status; 566 } 567 568 /** 569 * ixgbe_write_phy_reg_mdi - Writes a value to specified PHY register 570 * without SWFW lock 571 * @hw: pointer to hardware structure 572 * @reg_addr: 32 bit PHY register to write 573 * @device_type: 5 bit device type 574 * @phy_data: Data to write to the PHY register 575 **/ 576 s32 ixgbe_write_phy_reg_mdi(struct ixgbe_hw *hw, u32 reg_addr, 577 u32 device_type, u16 phy_data) 578 { 579 u32 i, command; 580 581 /* Put the data in the MDI single read and write data register*/ 582 IXGBE_WRITE_REG(hw, IXGBE_MSRWD, (u32)phy_data); 583 584 /* Setup and write the address cycle command */ 585 command = ((reg_addr << IXGBE_MSCA_NP_ADDR_SHIFT) | 586 (device_type << IXGBE_MSCA_DEV_TYPE_SHIFT) | 587 (hw->phy.mdio.prtad << IXGBE_MSCA_PHY_ADDR_SHIFT) | 588 (IXGBE_MSCA_ADDR_CYCLE | IXGBE_MSCA_MDI_COMMAND)); 589 590 IXGBE_WRITE_REG(hw, IXGBE_MSCA, command); 591 592 /* 593 * Check every 10 usec to see if the address cycle completed. 594 * The MDI Command bit will clear when the operation is 595 * complete 596 */ 597 for (i = 0; i < IXGBE_MDIO_COMMAND_TIMEOUT; i++) { 598 udelay(10); 599 600 command = IXGBE_READ_REG(hw, IXGBE_MSCA); 601 if ((command & IXGBE_MSCA_MDI_COMMAND) == 0) 602 break; 603 } 604 605 if ((command & IXGBE_MSCA_MDI_COMMAND) != 0) { 606 hw_dbg(hw, "PHY address cmd didn't complete\n"); 607 return IXGBE_ERR_PHY; 608 } 609 610 /* 611 * Address cycle complete, setup and write the write 612 * command 613 */ 614 command = ((reg_addr << IXGBE_MSCA_NP_ADDR_SHIFT) | 615 (device_type << IXGBE_MSCA_DEV_TYPE_SHIFT) | 616 (hw->phy.mdio.prtad << IXGBE_MSCA_PHY_ADDR_SHIFT) | 617 (IXGBE_MSCA_WRITE | IXGBE_MSCA_MDI_COMMAND)); 618 619 IXGBE_WRITE_REG(hw, IXGBE_MSCA, command); 620 621 /* Check every 10 usec to see if the address cycle 622 * completed. The MDI Command bit will clear when the 623 * operation is complete 624 */ 625 for (i = 0; i < IXGBE_MDIO_COMMAND_TIMEOUT; i++) { 626 udelay(10); 627 628 command = IXGBE_READ_REG(hw, IXGBE_MSCA); 629 if ((command & IXGBE_MSCA_MDI_COMMAND) == 0) 630 break; 631 } 632 633 if ((command & IXGBE_MSCA_MDI_COMMAND) != 0) { 634 hw_dbg(hw, "PHY write cmd didn't complete\n"); 635 return IXGBE_ERR_PHY; 636 } 637 638 return 0; 639 } 640 641 /** 642 * ixgbe_write_phy_reg_generic - Writes a value to specified PHY register 643 * using SWFW lock- this function is needed in most cases 644 * @hw: pointer to hardware structure 645 * @reg_addr: 32 bit PHY register to write 646 * @device_type: 5 bit device type 647 * @phy_data: Data to write to the PHY register 648 **/ 649 s32 ixgbe_write_phy_reg_generic(struct ixgbe_hw *hw, u32 reg_addr, 650 u32 device_type, u16 phy_data) 651 { 652 s32 status; 653 u32 gssr = hw->phy.phy_semaphore_mask; 654 655 if (hw->mac.ops.acquire_swfw_sync(hw, gssr) == 0) { 656 status = ixgbe_write_phy_reg_mdi(hw, reg_addr, device_type, 657 phy_data); 658 hw->mac.ops.release_swfw_sync(hw, gssr); 659 } else { 660 return IXGBE_ERR_SWFW_SYNC; 661 } 662 663 return status; 664 } 665 666 #define IXGBE_HW_READ_REG(addr) IXGBE_READ_REG(hw, addr) 667 668 /** 669 * ixgbe_msca_cmd - Write the command register and poll for completion/timeout 670 * @hw: pointer to hardware structure 671 * @cmd: command register value to write 672 **/ 673 static s32 ixgbe_msca_cmd(struct ixgbe_hw *hw, u32 cmd) 674 { 675 IXGBE_WRITE_REG(hw, IXGBE_MSCA, cmd); 676 677 return readx_poll_timeout(IXGBE_HW_READ_REG, IXGBE_MSCA, cmd, 678 !(cmd & IXGBE_MSCA_MDI_COMMAND), 10, 679 10 * IXGBE_MDIO_COMMAND_TIMEOUT); 680 } 681 682 /** 683 * ixgbe_mii_bus_read_generic - Read a clause 22/45 register with gssr flags 684 * @hw: pointer to hardware structure 685 * @addr: address 686 * @regnum: register number 687 * @gssr: semaphore flags to acquire 688 **/ 689 static s32 ixgbe_mii_bus_read_generic(struct ixgbe_hw *hw, int addr, 690 int regnum, u32 gssr) 691 { 692 u32 hwaddr, cmd; 693 s32 data; 694 695 if (hw->mac.ops.acquire_swfw_sync(hw, gssr)) 696 return -EBUSY; 697 698 hwaddr = addr << IXGBE_MSCA_PHY_ADDR_SHIFT; 699 if (regnum & MII_ADDR_C45) { 700 hwaddr |= regnum & GENMASK(21, 0); 701 cmd = hwaddr | IXGBE_MSCA_ADDR_CYCLE | IXGBE_MSCA_MDI_COMMAND; 702 } else { 703 hwaddr |= (regnum & GENMASK(5, 0)) << IXGBE_MSCA_DEV_TYPE_SHIFT; 704 cmd = hwaddr | IXGBE_MSCA_OLD_PROTOCOL | 705 IXGBE_MSCA_READ_AUTOINC | IXGBE_MSCA_MDI_COMMAND; 706 } 707 708 data = ixgbe_msca_cmd(hw, cmd); 709 if (data < 0) 710 goto mii_bus_read_done; 711 712 /* For a clause 45 access the address cycle just completed, we still 713 * need to do the read command, otherwise just get the data 714 */ 715 if (!(regnum & MII_ADDR_C45)) 716 goto do_mii_bus_read; 717 718 cmd = hwaddr | IXGBE_MSCA_READ | IXGBE_MSCA_MDI_COMMAND; 719 data = ixgbe_msca_cmd(hw, cmd); 720 if (data < 0) 721 goto mii_bus_read_done; 722 723 do_mii_bus_read: 724 data = IXGBE_READ_REG(hw, IXGBE_MSRWD); 725 data = (data >> IXGBE_MSRWD_READ_DATA_SHIFT) & GENMASK(16, 0); 726 727 mii_bus_read_done: 728 hw->mac.ops.release_swfw_sync(hw, gssr); 729 return data; 730 } 731 732 /** 733 * ixgbe_mii_bus_write_generic - Write a clause 22/45 register with gssr flags 734 * @hw: pointer to hardware structure 735 * @addr: address 736 * @regnum: register number 737 * @val: value to write 738 * @gssr: semaphore flags to acquire 739 **/ 740 static s32 ixgbe_mii_bus_write_generic(struct ixgbe_hw *hw, int addr, 741 int regnum, u16 val, u32 gssr) 742 { 743 u32 hwaddr, cmd; 744 s32 err; 745 746 if (hw->mac.ops.acquire_swfw_sync(hw, gssr)) 747 return -EBUSY; 748 749 IXGBE_WRITE_REG(hw, IXGBE_MSRWD, (u32)val); 750 751 hwaddr = addr << IXGBE_MSCA_PHY_ADDR_SHIFT; 752 if (regnum & MII_ADDR_C45) { 753 hwaddr |= regnum & GENMASK(21, 0); 754 cmd = hwaddr | IXGBE_MSCA_ADDR_CYCLE | IXGBE_MSCA_MDI_COMMAND; 755 } else { 756 hwaddr |= (regnum & GENMASK(5, 0)) << IXGBE_MSCA_DEV_TYPE_SHIFT; 757 cmd = hwaddr | IXGBE_MSCA_OLD_PROTOCOL | IXGBE_MSCA_WRITE | 758 IXGBE_MSCA_MDI_COMMAND; 759 } 760 761 /* For clause 45 this is an address cycle, for clause 22 this is the 762 * entire transaction 763 */ 764 err = ixgbe_msca_cmd(hw, cmd); 765 if (err < 0 || !(regnum & MII_ADDR_C45)) 766 goto mii_bus_write_done; 767 768 cmd = hwaddr | IXGBE_MSCA_WRITE | IXGBE_MSCA_MDI_COMMAND; 769 err = ixgbe_msca_cmd(hw, cmd); 770 771 mii_bus_write_done: 772 hw->mac.ops.release_swfw_sync(hw, gssr); 773 return err; 774 } 775 776 /** 777 * ixgbe_mii_bus_read - Read a clause 22/45 register 778 * @bus: pointer to mii_bus structure which points to our driver private 779 * @addr: address 780 * @regnum: register number 781 **/ 782 static s32 ixgbe_mii_bus_read(struct mii_bus *bus, int addr, int regnum) 783 { 784 struct ixgbe_adapter *adapter = bus->priv; 785 struct ixgbe_hw *hw = &adapter->hw; 786 u32 gssr = hw->phy.phy_semaphore_mask; 787 788 return ixgbe_mii_bus_read_generic(hw, addr, regnum, gssr); 789 } 790 791 /** 792 * ixgbe_mii_bus_write - Write a clause 22/45 register 793 * @bus: pointer to mii_bus structure which points to our driver private 794 * @addr: address 795 * @regnum: register number 796 * @val: value to write 797 **/ 798 static s32 ixgbe_mii_bus_write(struct mii_bus *bus, int addr, int regnum, 799 u16 val) 800 { 801 struct ixgbe_adapter *adapter = bus->priv; 802 struct ixgbe_hw *hw = &adapter->hw; 803 u32 gssr = hw->phy.phy_semaphore_mask; 804 805 return ixgbe_mii_bus_write_generic(hw, addr, regnum, val, gssr); 806 } 807 808 /** 809 * ixgbe_x550em_a_mii_bus_read - Read a clause 22/45 register on x550em_a 810 * @bus: pointer to mii_bus structure which points to our driver private 811 * @addr: address 812 * @regnum: register number 813 **/ 814 static s32 ixgbe_x550em_a_mii_bus_read(struct mii_bus *bus, int addr, 815 int regnum) 816 { 817 struct ixgbe_adapter *adapter = bus->priv; 818 struct ixgbe_hw *hw = &adapter->hw; 819 u32 gssr = hw->phy.phy_semaphore_mask; 820 821 gssr |= IXGBE_GSSR_TOKEN_SM | IXGBE_GSSR_PHY0_SM; 822 return ixgbe_mii_bus_read_generic(hw, addr, regnum, gssr); 823 } 824 825 /** 826 * ixgbe_x550em_a_mii_bus_write - Write a clause 22/45 register on x550em_a 827 * @bus: pointer to mii_bus structure which points to our driver private 828 * @addr: address 829 * @regnum: register number 830 * @val: value to write 831 **/ 832 static s32 ixgbe_x550em_a_mii_bus_write(struct mii_bus *bus, int addr, 833 int regnum, u16 val) 834 { 835 struct ixgbe_adapter *adapter = bus->priv; 836 struct ixgbe_hw *hw = &adapter->hw; 837 u32 gssr = hw->phy.phy_semaphore_mask; 838 839 gssr |= IXGBE_GSSR_TOKEN_SM | IXGBE_GSSR_PHY0_SM; 840 return ixgbe_mii_bus_write_generic(hw, addr, regnum, val, gssr); 841 } 842 843 /** 844 * ixgbe_get_first_secondary_devfn - get first device downstream of root port 845 * @devfn: PCI_DEVFN of root port on domain 0, bus 0 846 * 847 * Returns pci_dev pointer to PCI_DEVFN(0, 0) on subordinate side of root 848 * on domain 0, bus 0, devfn = 'devfn' 849 **/ 850 static struct pci_dev *ixgbe_get_first_secondary_devfn(unsigned int devfn) 851 { 852 struct pci_dev *rp_pdev; 853 int bus; 854 855 rp_pdev = pci_get_domain_bus_and_slot(0, 0, devfn); 856 if (rp_pdev && rp_pdev->subordinate) { 857 bus = rp_pdev->subordinate->number; 858 return pci_get_domain_bus_and_slot(0, bus, 0); 859 } 860 861 return NULL; 862 } 863 864 /** 865 * ixgbe_x550em_a_has_mii - is this the first ixgbe x550em_a PCI function? 866 * @hw: pointer to hardware structure 867 * 868 * Returns true if hw points to lowest numbered PCI B:D.F x550_em_a device in 869 * the SoC. There are up to 4 MACs sharing a single MDIO bus on the x550em_a, 870 * but we only want to register one MDIO bus. 871 **/ 872 static bool ixgbe_x550em_a_has_mii(struct ixgbe_hw *hw) 873 { 874 struct ixgbe_adapter *adapter = hw->back; 875 struct pci_dev *pdev = adapter->pdev; 876 struct pci_dev *func0_pdev; 877 878 /* For the C3000 family of SoCs (x550em_a) the internal ixgbe devices 879 * are always downstream of root ports @ 0000:00:16.0 & 0000:00:17.0 880 * It's not valid for function 0 to be disabled and function 1 is up, 881 * so the lowest numbered ixgbe dev will be device 0 function 0 on one 882 * of those two root ports 883 */ 884 func0_pdev = ixgbe_get_first_secondary_devfn(PCI_DEVFN(0x16, 0)); 885 if (func0_pdev) { 886 if (func0_pdev == pdev) 887 return true; 888 else 889 return false; 890 } 891 func0_pdev = ixgbe_get_first_secondary_devfn(PCI_DEVFN(0x17, 0)); 892 if (func0_pdev == pdev) 893 return true; 894 895 return false; 896 } 897 898 /** 899 * ixgbe_mii_bus_init - mii_bus structure setup 900 * @hw: pointer to hardware structure 901 * 902 * Returns 0 on success, negative on failure 903 * 904 * ixgbe_mii_bus_init initializes a mii_bus structure in adapter 905 **/ 906 s32 ixgbe_mii_bus_init(struct ixgbe_hw *hw) 907 { 908 s32 (*write)(struct mii_bus *bus, int addr, int regnum, u16 val); 909 s32 (*read)(struct mii_bus *bus, int addr, int regnum); 910 struct ixgbe_adapter *adapter = hw->back; 911 struct pci_dev *pdev = adapter->pdev; 912 struct device *dev = &adapter->netdev->dev; 913 struct mii_bus *bus; 914 915 switch (hw->device_id) { 916 /* C3000 SoCs */ 917 case IXGBE_DEV_ID_X550EM_A_KR: 918 case IXGBE_DEV_ID_X550EM_A_KR_L: 919 case IXGBE_DEV_ID_X550EM_A_SFP_N: 920 case IXGBE_DEV_ID_X550EM_A_SGMII: 921 case IXGBE_DEV_ID_X550EM_A_SGMII_L: 922 case IXGBE_DEV_ID_X550EM_A_10G_T: 923 case IXGBE_DEV_ID_X550EM_A_SFP: 924 case IXGBE_DEV_ID_X550EM_A_1G_T: 925 case IXGBE_DEV_ID_X550EM_A_1G_T_L: 926 if (!ixgbe_x550em_a_has_mii(hw)) 927 return 0; 928 read = &ixgbe_x550em_a_mii_bus_read; 929 write = &ixgbe_x550em_a_mii_bus_write; 930 break; 931 default: 932 read = &ixgbe_mii_bus_read; 933 write = &ixgbe_mii_bus_write; 934 break; 935 } 936 937 bus = devm_mdiobus_alloc(dev); 938 if (!bus) 939 return -ENOMEM; 940 941 bus->read = read; 942 bus->write = write; 943 944 /* Use the position of the device in the PCI hierarchy as the id */ 945 snprintf(bus->id, MII_BUS_ID_SIZE, "%s-mdio-%s", ixgbe_driver_name, 946 pci_name(pdev)); 947 948 bus->name = "ixgbe-mdio"; 949 bus->priv = adapter; 950 bus->parent = dev; 951 bus->phy_mask = GENMASK(31, 0); 952 953 /* Support clause 22/45 natively. ixgbe_probe() sets MDIO_EMULATE_C22 954 * unfortunately that causes some clause 22 frames to be sent with 955 * clause 45 addressing. We don't want that. 956 */ 957 hw->phy.mdio.mode_support = MDIO_SUPPORTS_C45 | MDIO_SUPPORTS_C22; 958 959 adapter->mii_bus = bus; 960 return mdiobus_register(bus); 961 } 962 963 /** 964 * ixgbe_setup_phy_link_generic - Set and restart autoneg 965 * @hw: pointer to hardware structure 966 * 967 * Restart autonegotiation and PHY and waits for completion. 968 **/ 969 s32 ixgbe_setup_phy_link_generic(struct ixgbe_hw *hw) 970 { 971 s32 status = 0; 972 u16 autoneg_reg = IXGBE_MII_AUTONEG_REG; 973 bool autoneg = false; 974 ixgbe_link_speed speed; 975 976 ixgbe_get_copper_link_capabilities_generic(hw, &speed, &autoneg); 977 978 /* Set or unset auto-negotiation 10G advertisement */ 979 hw->phy.ops.read_reg(hw, MDIO_AN_10GBT_CTRL, MDIO_MMD_AN, &autoneg_reg); 980 981 autoneg_reg &= ~MDIO_AN_10GBT_CTRL_ADV10G; 982 if ((hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_10GB_FULL) && 983 (speed & IXGBE_LINK_SPEED_10GB_FULL)) 984 autoneg_reg |= MDIO_AN_10GBT_CTRL_ADV10G; 985 986 hw->phy.ops.write_reg(hw, MDIO_AN_10GBT_CTRL, MDIO_MMD_AN, autoneg_reg); 987 988 hw->phy.ops.read_reg(hw, IXGBE_MII_AUTONEG_VENDOR_PROVISION_1_REG, 989 MDIO_MMD_AN, &autoneg_reg); 990 991 if (hw->mac.type == ixgbe_mac_X550) { 992 /* Set or unset auto-negotiation 5G advertisement */ 993 autoneg_reg &= ~IXGBE_MII_5GBASE_T_ADVERTISE; 994 if ((hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_5GB_FULL) && 995 (speed & IXGBE_LINK_SPEED_5GB_FULL)) 996 autoneg_reg |= IXGBE_MII_5GBASE_T_ADVERTISE; 997 998 /* Set or unset auto-negotiation 2.5G advertisement */ 999 autoneg_reg &= ~IXGBE_MII_2_5GBASE_T_ADVERTISE; 1000 if ((hw->phy.autoneg_advertised & 1001 IXGBE_LINK_SPEED_2_5GB_FULL) && 1002 (speed & IXGBE_LINK_SPEED_2_5GB_FULL)) 1003 autoneg_reg |= IXGBE_MII_2_5GBASE_T_ADVERTISE; 1004 } 1005 1006 /* Set or unset auto-negotiation 1G advertisement */ 1007 autoneg_reg &= ~IXGBE_MII_1GBASE_T_ADVERTISE; 1008 if ((hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_1GB_FULL) && 1009 (speed & IXGBE_LINK_SPEED_1GB_FULL)) 1010 autoneg_reg |= IXGBE_MII_1GBASE_T_ADVERTISE; 1011 1012 hw->phy.ops.write_reg(hw, IXGBE_MII_AUTONEG_VENDOR_PROVISION_1_REG, 1013 MDIO_MMD_AN, autoneg_reg); 1014 1015 /* Set or unset auto-negotiation 100M advertisement */ 1016 hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE, MDIO_MMD_AN, &autoneg_reg); 1017 1018 autoneg_reg &= ~(ADVERTISE_100FULL | ADVERTISE_100HALF); 1019 if ((hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_100_FULL) && 1020 (speed & IXGBE_LINK_SPEED_100_FULL)) 1021 autoneg_reg |= ADVERTISE_100FULL; 1022 1023 hw->phy.ops.write_reg(hw, MDIO_AN_ADVERTISE, MDIO_MMD_AN, autoneg_reg); 1024 1025 /* Blocked by MNG FW so don't reset PHY */ 1026 if (ixgbe_check_reset_blocked(hw)) 1027 return 0; 1028 1029 /* Restart PHY autonegotiation and wait for completion */ 1030 hw->phy.ops.read_reg(hw, MDIO_CTRL1, 1031 MDIO_MMD_AN, &autoneg_reg); 1032 1033 autoneg_reg |= MDIO_AN_CTRL1_RESTART; 1034 1035 hw->phy.ops.write_reg(hw, MDIO_CTRL1, 1036 MDIO_MMD_AN, autoneg_reg); 1037 1038 return status; 1039 } 1040 1041 /** 1042 * ixgbe_setup_phy_link_speed_generic - Sets the auto advertised capabilities 1043 * @hw: pointer to hardware structure 1044 * @speed: new link speed 1045 * @autoneg_wait_to_complete: unused 1046 **/ 1047 s32 ixgbe_setup_phy_link_speed_generic(struct ixgbe_hw *hw, 1048 ixgbe_link_speed speed, 1049 bool autoneg_wait_to_complete) 1050 { 1051 /* Clear autoneg_advertised and set new values based on input link 1052 * speed. 1053 */ 1054 hw->phy.autoneg_advertised = 0; 1055 1056 if (speed & IXGBE_LINK_SPEED_10GB_FULL) 1057 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL; 1058 1059 if (speed & IXGBE_LINK_SPEED_5GB_FULL) 1060 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_5GB_FULL; 1061 1062 if (speed & IXGBE_LINK_SPEED_2_5GB_FULL) 1063 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_2_5GB_FULL; 1064 1065 if (speed & IXGBE_LINK_SPEED_1GB_FULL) 1066 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL; 1067 1068 if (speed & IXGBE_LINK_SPEED_100_FULL) 1069 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_100_FULL; 1070 1071 if (speed & IXGBE_LINK_SPEED_10_FULL) 1072 hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10_FULL; 1073 1074 /* Setup link based on the new speed settings */ 1075 if (hw->phy.ops.setup_link) 1076 hw->phy.ops.setup_link(hw); 1077 1078 return 0; 1079 } 1080 1081 /** 1082 * ixgbe_get_copper_speeds_supported - Get copper link speed from phy 1083 * @hw: pointer to hardware structure 1084 * 1085 * Determines the supported link capabilities by reading the PHY auto 1086 * negotiation register. 1087 */ 1088 static s32 ixgbe_get_copper_speeds_supported(struct ixgbe_hw *hw) 1089 { 1090 u16 speed_ability; 1091 s32 status; 1092 1093 status = hw->phy.ops.read_reg(hw, MDIO_SPEED, MDIO_MMD_PMAPMD, 1094 &speed_ability); 1095 if (status) 1096 return status; 1097 1098 if (speed_ability & MDIO_SPEED_10G) 1099 hw->phy.speeds_supported |= IXGBE_LINK_SPEED_10GB_FULL; 1100 if (speed_ability & MDIO_PMA_SPEED_1000) 1101 hw->phy.speeds_supported |= IXGBE_LINK_SPEED_1GB_FULL; 1102 if (speed_ability & MDIO_PMA_SPEED_100) 1103 hw->phy.speeds_supported |= IXGBE_LINK_SPEED_100_FULL; 1104 1105 switch (hw->mac.type) { 1106 case ixgbe_mac_X550: 1107 hw->phy.speeds_supported |= IXGBE_LINK_SPEED_2_5GB_FULL; 1108 hw->phy.speeds_supported |= IXGBE_LINK_SPEED_5GB_FULL; 1109 break; 1110 case ixgbe_mac_X550EM_x: 1111 case ixgbe_mac_x550em_a: 1112 hw->phy.speeds_supported &= ~IXGBE_LINK_SPEED_100_FULL; 1113 break; 1114 default: 1115 break; 1116 } 1117 1118 return 0; 1119 } 1120 1121 /** 1122 * ixgbe_get_copper_link_capabilities_generic - Determines link capabilities 1123 * @hw: pointer to hardware structure 1124 * @speed: pointer to link speed 1125 * @autoneg: boolean auto-negotiation value 1126 */ 1127 s32 ixgbe_get_copper_link_capabilities_generic(struct ixgbe_hw *hw, 1128 ixgbe_link_speed *speed, 1129 bool *autoneg) 1130 { 1131 s32 status = 0; 1132 1133 *autoneg = true; 1134 if (!hw->phy.speeds_supported) 1135 status = ixgbe_get_copper_speeds_supported(hw); 1136 1137 *speed = hw->phy.speeds_supported; 1138 return status; 1139 } 1140 1141 /** 1142 * ixgbe_check_phy_link_tnx - Determine link and speed status 1143 * @hw: pointer to hardware structure 1144 * @speed: link speed 1145 * @link_up: status of link 1146 * 1147 * Reads the VS1 register to determine if link is up and the current speed for 1148 * the PHY. 1149 **/ 1150 s32 ixgbe_check_phy_link_tnx(struct ixgbe_hw *hw, ixgbe_link_speed *speed, 1151 bool *link_up) 1152 { 1153 s32 status; 1154 u32 time_out; 1155 u32 max_time_out = 10; 1156 u16 phy_link = 0; 1157 u16 phy_speed = 0; 1158 u16 phy_data = 0; 1159 1160 /* Initialize speed and link to default case */ 1161 *link_up = false; 1162 *speed = IXGBE_LINK_SPEED_10GB_FULL; 1163 1164 /* 1165 * Check current speed and link status of the PHY register. 1166 * This is a vendor specific register and may have to 1167 * be changed for other copper PHYs. 1168 */ 1169 for (time_out = 0; time_out < max_time_out; time_out++) { 1170 udelay(10); 1171 status = hw->phy.ops.read_reg(hw, 1172 MDIO_STAT1, 1173 MDIO_MMD_VEND1, 1174 &phy_data); 1175 phy_link = phy_data & 1176 IXGBE_MDIO_VENDOR_SPECIFIC_1_LINK_STATUS; 1177 phy_speed = phy_data & 1178 IXGBE_MDIO_VENDOR_SPECIFIC_1_SPEED_STATUS; 1179 if (phy_link == IXGBE_MDIO_VENDOR_SPECIFIC_1_LINK_STATUS) { 1180 *link_up = true; 1181 if (phy_speed == 1182 IXGBE_MDIO_VENDOR_SPECIFIC_1_SPEED_STATUS) 1183 *speed = IXGBE_LINK_SPEED_1GB_FULL; 1184 break; 1185 } 1186 } 1187 1188 return status; 1189 } 1190 1191 /** 1192 * ixgbe_setup_phy_link_tnx - Set and restart autoneg 1193 * @hw: pointer to hardware structure 1194 * 1195 * Restart autonegotiation and PHY and waits for completion. 1196 * This function always returns success, this is nessary since 1197 * it is called via a function pointer that could call other 1198 * functions that could return an error. 1199 **/ 1200 s32 ixgbe_setup_phy_link_tnx(struct ixgbe_hw *hw) 1201 { 1202 u16 autoneg_reg = IXGBE_MII_AUTONEG_REG; 1203 bool autoneg = false; 1204 ixgbe_link_speed speed; 1205 1206 ixgbe_get_copper_link_capabilities_generic(hw, &speed, &autoneg); 1207 1208 if (speed & IXGBE_LINK_SPEED_10GB_FULL) { 1209 /* Set or unset auto-negotiation 10G advertisement */ 1210 hw->phy.ops.read_reg(hw, MDIO_AN_10GBT_CTRL, 1211 MDIO_MMD_AN, 1212 &autoneg_reg); 1213 1214 autoneg_reg &= ~MDIO_AN_10GBT_CTRL_ADV10G; 1215 if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_10GB_FULL) 1216 autoneg_reg |= MDIO_AN_10GBT_CTRL_ADV10G; 1217 1218 hw->phy.ops.write_reg(hw, MDIO_AN_10GBT_CTRL, 1219 MDIO_MMD_AN, 1220 autoneg_reg); 1221 } 1222 1223 if (speed & IXGBE_LINK_SPEED_1GB_FULL) { 1224 /* Set or unset auto-negotiation 1G advertisement */ 1225 hw->phy.ops.read_reg(hw, IXGBE_MII_AUTONEG_XNP_TX_REG, 1226 MDIO_MMD_AN, 1227 &autoneg_reg); 1228 1229 autoneg_reg &= ~IXGBE_MII_1GBASE_T_ADVERTISE_XNP_TX; 1230 if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_1GB_FULL) 1231 autoneg_reg |= IXGBE_MII_1GBASE_T_ADVERTISE_XNP_TX; 1232 1233 hw->phy.ops.write_reg(hw, IXGBE_MII_AUTONEG_XNP_TX_REG, 1234 MDIO_MMD_AN, 1235 autoneg_reg); 1236 } 1237 1238 if (speed & IXGBE_LINK_SPEED_100_FULL) { 1239 /* Set or unset auto-negotiation 100M advertisement */ 1240 hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE, 1241 MDIO_MMD_AN, 1242 &autoneg_reg); 1243 1244 autoneg_reg &= ~(ADVERTISE_100FULL | 1245 ADVERTISE_100HALF); 1246 if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_100_FULL) 1247 autoneg_reg |= ADVERTISE_100FULL; 1248 1249 hw->phy.ops.write_reg(hw, MDIO_AN_ADVERTISE, 1250 MDIO_MMD_AN, 1251 autoneg_reg); 1252 } 1253 1254 /* Blocked by MNG FW so don't reset PHY */ 1255 if (ixgbe_check_reset_blocked(hw)) 1256 return 0; 1257 1258 /* Restart PHY autonegotiation and wait for completion */ 1259 hw->phy.ops.read_reg(hw, MDIO_CTRL1, 1260 MDIO_MMD_AN, &autoneg_reg); 1261 1262 autoneg_reg |= MDIO_AN_CTRL1_RESTART; 1263 1264 hw->phy.ops.write_reg(hw, MDIO_CTRL1, 1265 MDIO_MMD_AN, autoneg_reg); 1266 return 0; 1267 } 1268 1269 /** 1270 * ixgbe_reset_phy_nl - Performs a PHY reset 1271 * @hw: pointer to hardware structure 1272 **/ 1273 s32 ixgbe_reset_phy_nl(struct ixgbe_hw *hw) 1274 { 1275 u16 phy_offset, control, eword, edata, block_crc; 1276 bool end_data = false; 1277 u16 list_offset, data_offset; 1278 u16 phy_data = 0; 1279 s32 ret_val; 1280 u32 i; 1281 1282 /* Blocked by MNG FW so bail */ 1283 if (ixgbe_check_reset_blocked(hw)) 1284 return 0; 1285 1286 hw->phy.ops.read_reg(hw, MDIO_CTRL1, MDIO_MMD_PHYXS, &phy_data); 1287 1288 /* reset the PHY and poll for completion */ 1289 hw->phy.ops.write_reg(hw, MDIO_CTRL1, MDIO_MMD_PHYXS, 1290 (phy_data | MDIO_CTRL1_RESET)); 1291 1292 for (i = 0; i < 100; i++) { 1293 hw->phy.ops.read_reg(hw, MDIO_CTRL1, MDIO_MMD_PHYXS, 1294 &phy_data); 1295 if ((phy_data & MDIO_CTRL1_RESET) == 0) 1296 break; 1297 usleep_range(10000, 20000); 1298 } 1299 1300 if ((phy_data & MDIO_CTRL1_RESET) != 0) { 1301 hw_dbg(hw, "PHY reset did not complete.\n"); 1302 return IXGBE_ERR_PHY; 1303 } 1304 1305 /* Get init offsets */ 1306 ret_val = ixgbe_get_sfp_init_sequence_offsets(hw, &list_offset, 1307 &data_offset); 1308 if (ret_val) 1309 return ret_val; 1310 1311 ret_val = hw->eeprom.ops.read(hw, data_offset, &block_crc); 1312 data_offset++; 1313 while (!end_data) { 1314 /* 1315 * Read control word from PHY init contents offset 1316 */ 1317 ret_val = hw->eeprom.ops.read(hw, data_offset, &eword); 1318 if (ret_val) 1319 goto err_eeprom; 1320 control = (eword & IXGBE_CONTROL_MASK_NL) >> 1321 IXGBE_CONTROL_SHIFT_NL; 1322 edata = eword & IXGBE_DATA_MASK_NL; 1323 switch (control) { 1324 case IXGBE_DELAY_NL: 1325 data_offset++; 1326 hw_dbg(hw, "DELAY: %d MS\n", edata); 1327 usleep_range(edata * 1000, edata * 2000); 1328 break; 1329 case IXGBE_DATA_NL: 1330 hw_dbg(hw, "DATA:\n"); 1331 data_offset++; 1332 ret_val = hw->eeprom.ops.read(hw, data_offset++, 1333 &phy_offset); 1334 if (ret_val) 1335 goto err_eeprom; 1336 for (i = 0; i < edata; i++) { 1337 ret_val = hw->eeprom.ops.read(hw, data_offset, 1338 &eword); 1339 if (ret_val) 1340 goto err_eeprom; 1341 hw->phy.ops.write_reg(hw, phy_offset, 1342 MDIO_MMD_PMAPMD, eword); 1343 hw_dbg(hw, "Wrote %4.4x to %4.4x\n", eword, 1344 phy_offset); 1345 data_offset++; 1346 phy_offset++; 1347 } 1348 break; 1349 case IXGBE_CONTROL_NL: 1350 data_offset++; 1351 hw_dbg(hw, "CONTROL:\n"); 1352 if (edata == IXGBE_CONTROL_EOL_NL) { 1353 hw_dbg(hw, "EOL\n"); 1354 end_data = true; 1355 } else if (edata == IXGBE_CONTROL_SOL_NL) { 1356 hw_dbg(hw, "SOL\n"); 1357 } else { 1358 hw_dbg(hw, "Bad control value\n"); 1359 return IXGBE_ERR_PHY; 1360 } 1361 break; 1362 default: 1363 hw_dbg(hw, "Bad control type\n"); 1364 return IXGBE_ERR_PHY; 1365 } 1366 } 1367 1368 return ret_val; 1369 1370 err_eeprom: 1371 hw_err(hw, "eeprom read at offset %d failed\n", data_offset); 1372 return IXGBE_ERR_PHY; 1373 } 1374 1375 /** 1376 * ixgbe_identify_module_generic - Identifies module type 1377 * @hw: pointer to hardware structure 1378 * 1379 * Determines HW type and calls appropriate function. 1380 **/ 1381 s32 ixgbe_identify_module_generic(struct ixgbe_hw *hw) 1382 { 1383 switch (hw->mac.ops.get_media_type(hw)) { 1384 case ixgbe_media_type_fiber: 1385 return ixgbe_identify_sfp_module_generic(hw); 1386 case ixgbe_media_type_fiber_qsfp: 1387 return ixgbe_identify_qsfp_module_generic(hw); 1388 default: 1389 hw->phy.sfp_type = ixgbe_sfp_type_not_present; 1390 return IXGBE_ERR_SFP_NOT_PRESENT; 1391 } 1392 1393 return IXGBE_ERR_SFP_NOT_PRESENT; 1394 } 1395 1396 /** 1397 * ixgbe_identify_sfp_module_generic - Identifies SFP modules 1398 * @hw: pointer to hardware structure 1399 * 1400 * Searches for and identifies the SFP module and assigns appropriate PHY type. 1401 **/ 1402 s32 ixgbe_identify_sfp_module_generic(struct ixgbe_hw *hw) 1403 { 1404 struct ixgbe_adapter *adapter = hw->back; 1405 s32 status; 1406 u32 vendor_oui = 0; 1407 enum ixgbe_sfp_type stored_sfp_type = hw->phy.sfp_type; 1408 u8 identifier = 0; 1409 u8 comp_codes_1g = 0; 1410 u8 comp_codes_10g = 0; 1411 u8 oui_bytes[3] = {0, 0, 0}; 1412 u8 cable_tech = 0; 1413 u8 cable_spec = 0; 1414 u16 enforce_sfp = 0; 1415 1416 if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_fiber) { 1417 hw->phy.sfp_type = ixgbe_sfp_type_not_present; 1418 return IXGBE_ERR_SFP_NOT_PRESENT; 1419 } 1420 1421 /* LAN ID is needed for sfp_type determination */ 1422 hw->mac.ops.set_lan_id(hw); 1423 1424 status = hw->phy.ops.read_i2c_eeprom(hw, 1425 IXGBE_SFF_IDENTIFIER, 1426 &identifier); 1427 1428 if (status) 1429 goto err_read_i2c_eeprom; 1430 1431 if (identifier != IXGBE_SFF_IDENTIFIER_SFP) { 1432 hw->phy.type = ixgbe_phy_sfp_unsupported; 1433 return IXGBE_ERR_SFP_NOT_SUPPORTED; 1434 } 1435 status = hw->phy.ops.read_i2c_eeprom(hw, 1436 IXGBE_SFF_1GBE_COMP_CODES, 1437 &comp_codes_1g); 1438 1439 if (status) 1440 goto err_read_i2c_eeprom; 1441 1442 status = hw->phy.ops.read_i2c_eeprom(hw, 1443 IXGBE_SFF_10GBE_COMP_CODES, 1444 &comp_codes_10g); 1445 1446 if (status) 1447 goto err_read_i2c_eeprom; 1448 status = hw->phy.ops.read_i2c_eeprom(hw, 1449 IXGBE_SFF_CABLE_TECHNOLOGY, 1450 &cable_tech); 1451 1452 if (status) 1453 goto err_read_i2c_eeprom; 1454 1455 /* ID Module 1456 * ========= 1457 * 0 SFP_DA_CU 1458 * 1 SFP_SR 1459 * 2 SFP_LR 1460 * 3 SFP_DA_CORE0 - 82599-specific 1461 * 4 SFP_DA_CORE1 - 82599-specific 1462 * 5 SFP_SR/LR_CORE0 - 82599-specific 1463 * 6 SFP_SR/LR_CORE1 - 82599-specific 1464 * 7 SFP_act_lmt_DA_CORE0 - 82599-specific 1465 * 8 SFP_act_lmt_DA_CORE1 - 82599-specific 1466 * 9 SFP_1g_cu_CORE0 - 82599-specific 1467 * 10 SFP_1g_cu_CORE1 - 82599-specific 1468 * 11 SFP_1g_sx_CORE0 - 82599-specific 1469 * 12 SFP_1g_sx_CORE1 - 82599-specific 1470 */ 1471 if (hw->mac.type == ixgbe_mac_82598EB) { 1472 if (cable_tech & IXGBE_SFF_DA_PASSIVE_CABLE) 1473 hw->phy.sfp_type = ixgbe_sfp_type_da_cu; 1474 else if (comp_codes_10g & IXGBE_SFF_10GBASESR_CAPABLE) 1475 hw->phy.sfp_type = ixgbe_sfp_type_sr; 1476 else if (comp_codes_10g & IXGBE_SFF_10GBASELR_CAPABLE) 1477 hw->phy.sfp_type = ixgbe_sfp_type_lr; 1478 else 1479 hw->phy.sfp_type = ixgbe_sfp_type_unknown; 1480 } else { 1481 if (cable_tech & IXGBE_SFF_DA_PASSIVE_CABLE) { 1482 if (hw->bus.lan_id == 0) 1483 hw->phy.sfp_type = 1484 ixgbe_sfp_type_da_cu_core0; 1485 else 1486 hw->phy.sfp_type = 1487 ixgbe_sfp_type_da_cu_core1; 1488 } else if (cable_tech & IXGBE_SFF_DA_ACTIVE_CABLE) { 1489 hw->phy.ops.read_i2c_eeprom( 1490 hw, IXGBE_SFF_CABLE_SPEC_COMP, 1491 &cable_spec); 1492 if (cable_spec & 1493 IXGBE_SFF_DA_SPEC_ACTIVE_LIMITING) { 1494 if (hw->bus.lan_id == 0) 1495 hw->phy.sfp_type = 1496 ixgbe_sfp_type_da_act_lmt_core0; 1497 else 1498 hw->phy.sfp_type = 1499 ixgbe_sfp_type_da_act_lmt_core1; 1500 } else { 1501 hw->phy.sfp_type = 1502 ixgbe_sfp_type_unknown; 1503 } 1504 } else if (comp_codes_10g & 1505 (IXGBE_SFF_10GBASESR_CAPABLE | 1506 IXGBE_SFF_10GBASELR_CAPABLE)) { 1507 if (hw->bus.lan_id == 0) 1508 hw->phy.sfp_type = 1509 ixgbe_sfp_type_srlr_core0; 1510 else 1511 hw->phy.sfp_type = 1512 ixgbe_sfp_type_srlr_core1; 1513 } else if (comp_codes_1g & IXGBE_SFF_1GBASET_CAPABLE) { 1514 if (hw->bus.lan_id == 0) 1515 hw->phy.sfp_type = 1516 ixgbe_sfp_type_1g_cu_core0; 1517 else 1518 hw->phy.sfp_type = 1519 ixgbe_sfp_type_1g_cu_core1; 1520 } else if (comp_codes_1g & IXGBE_SFF_1GBASESX_CAPABLE) { 1521 if (hw->bus.lan_id == 0) 1522 hw->phy.sfp_type = 1523 ixgbe_sfp_type_1g_sx_core0; 1524 else 1525 hw->phy.sfp_type = 1526 ixgbe_sfp_type_1g_sx_core1; 1527 } else if (comp_codes_1g & IXGBE_SFF_1GBASELX_CAPABLE) { 1528 if (hw->bus.lan_id == 0) 1529 hw->phy.sfp_type = 1530 ixgbe_sfp_type_1g_lx_core0; 1531 else 1532 hw->phy.sfp_type = 1533 ixgbe_sfp_type_1g_lx_core1; 1534 } else { 1535 hw->phy.sfp_type = ixgbe_sfp_type_unknown; 1536 } 1537 } 1538 1539 if (hw->phy.sfp_type != stored_sfp_type) 1540 hw->phy.sfp_setup_needed = true; 1541 1542 /* Determine if the SFP+ PHY is dual speed or not. */ 1543 hw->phy.multispeed_fiber = false; 1544 if (((comp_codes_1g & IXGBE_SFF_1GBASESX_CAPABLE) && 1545 (comp_codes_10g & IXGBE_SFF_10GBASESR_CAPABLE)) || 1546 ((comp_codes_1g & IXGBE_SFF_1GBASELX_CAPABLE) && 1547 (comp_codes_10g & IXGBE_SFF_10GBASELR_CAPABLE))) 1548 hw->phy.multispeed_fiber = true; 1549 1550 /* Determine PHY vendor */ 1551 if (hw->phy.type != ixgbe_phy_nl) { 1552 hw->phy.id = identifier; 1553 status = hw->phy.ops.read_i2c_eeprom(hw, 1554 IXGBE_SFF_VENDOR_OUI_BYTE0, 1555 &oui_bytes[0]); 1556 1557 if (status != 0) 1558 goto err_read_i2c_eeprom; 1559 1560 status = hw->phy.ops.read_i2c_eeprom(hw, 1561 IXGBE_SFF_VENDOR_OUI_BYTE1, 1562 &oui_bytes[1]); 1563 1564 if (status != 0) 1565 goto err_read_i2c_eeprom; 1566 1567 status = hw->phy.ops.read_i2c_eeprom(hw, 1568 IXGBE_SFF_VENDOR_OUI_BYTE2, 1569 &oui_bytes[2]); 1570 1571 if (status != 0) 1572 goto err_read_i2c_eeprom; 1573 1574 vendor_oui = 1575 ((oui_bytes[0] << IXGBE_SFF_VENDOR_OUI_BYTE0_SHIFT) | 1576 (oui_bytes[1] << IXGBE_SFF_VENDOR_OUI_BYTE1_SHIFT) | 1577 (oui_bytes[2] << IXGBE_SFF_VENDOR_OUI_BYTE2_SHIFT)); 1578 1579 switch (vendor_oui) { 1580 case IXGBE_SFF_VENDOR_OUI_TYCO: 1581 if (cable_tech & IXGBE_SFF_DA_PASSIVE_CABLE) 1582 hw->phy.type = 1583 ixgbe_phy_sfp_passive_tyco; 1584 break; 1585 case IXGBE_SFF_VENDOR_OUI_FTL: 1586 if (cable_tech & IXGBE_SFF_DA_ACTIVE_CABLE) 1587 hw->phy.type = ixgbe_phy_sfp_ftl_active; 1588 else 1589 hw->phy.type = ixgbe_phy_sfp_ftl; 1590 break; 1591 case IXGBE_SFF_VENDOR_OUI_AVAGO: 1592 hw->phy.type = ixgbe_phy_sfp_avago; 1593 break; 1594 case IXGBE_SFF_VENDOR_OUI_INTEL: 1595 hw->phy.type = ixgbe_phy_sfp_intel; 1596 break; 1597 default: 1598 if (cable_tech & IXGBE_SFF_DA_PASSIVE_CABLE) 1599 hw->phy.type = 1600 ixgbe_phy_sfp_passive_unknown; 1601 else if (cable_tech & IXGBE_SFF_DA_ACTIVE_CABLE) 1602 hw->phy.type = 1603 ixgbe_phy_sfp_active_unknown; 1604 else 1605 hw->phy.type = ixgbe_phy_sfp_unknown; 1606 break; 1607 } 1608 } 1609 1610 /* Allow any DA cable vendor */ 1611 if (cable_tech & (IXGBE_SFF_DA_PASSIVE_CABLE | 1612 IXGBE_SFF_DA_ACTIVE_CABLE)) 1613 return 0; 1614 1615 /* Verify supported 1G SFP modules */ 1616 if (comp_codes_10g == 0 && 1617 !(hw->phy.sfp_type == ixgbe_sfp_type_1g_cu_core1 || 1618 hw->phy.sfp_type == ixgbe_sfp_type_1g_cu_core0 || 1619 hw->phy.sfp_type == ixgbe_sfp_type_1g_lx_core0 || 1620 hw->phy.sfp_type == ixgbe_sfp_type_1g_lx_core1 || 1621 hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core0 || 1622 hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core1)) { 1623 hw->phy.type = ixgbe_phy_sfp_unsupported; 1624 return IXGBE_ERR_SFP_NOT_SUPPORTED; 1625 } 1626 1627 /* Anything else 82598-based is supported */ 1628 if (hw->mac.type == ixgbe_mac_82598EB) 1629 return 0; 1630 1631 hw->mac.ops.get_device_caps(hw, &enforce_sfp); 1632 if (!(enforce_sfp & IXGBE_DEVICE_CAPS_ALLOW_ANY_SFP) && 1633 !(hw->phy.sfp_type == ixgbe_sfp_type_1g_cu_core0 || 1634 hw->phy.sfp_type == ixgbe_sfp_type_1g_cu_core1 || 1635 hw->phy.sfp_type == ixgbe_sfp_type_1g_lx_core0 || 1636 hw->phy.sfp_type == ixgbe_sfp_type_1g_lx_core1 || 1637 hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core0 || 1638 hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core1)) { 1639 /* Make sure we're a supported PHY type */ 1640 if (hw->phy.type == ixgbe_phy_sfp_intel) 1641 return 0; 1642 if (hw->allow_unsupported_sfp) { 1643 e_warn(drv, "WARNING: Intel (R) Network Connections are quality tested using Intel (R) Ethernet Optics. Using untested modules is not supported and may cause unstable operation or damage to the module or the adapter. Intel Corporation is not responsible for any harm caused by using untested modules.\n"); 1644 return 0; 1645 } 1646 hw_dbg(hw, "SFP+ module not supported\n"); 1647 hw->phy.type = ixgbe_phy_sfp_unsupported; 1648 return IXGBE_ERR_SFP_NOT_SUPPORTED; 1649 } 1650 return 0; 1651 1652 err_read_i2c_eeprom: 1653 hw->phy.sfp_type = ixgbe_sfp_type_not_present; 1654 if (hw->phy.type != ixgbe_phy_nl) { 1655 hw->phy.id = 0; 1656 hw->phy.type = ixgbe_phy_unknown; 1657 } 1658 return IXGBE_ERR_SFP_NOT_PRESENT; 1659 } 1660 1661 /** 1662 * ixgbe_identify_qsfp_module_generic - Identifies QSFP modules 1663 * @hw: pointer to hardware structure 1664 * 1665 * Searches for and identifies the QSFP module and assigns appropriate PHY type 1666 **/ 1667 static s32 ixgbe_identify_qsfp_module_generic(struct ixgbe_hw *hw) 1668 { 1669 struct ixgbe_adapter *adapter = hw->back; 1670 s32 status; 1671 u32 vendor_oui = 0; 1672 enum ixgbe_sfp_type stored_sfp_type = hw->phy.sfp_type; 1673 u8 identifier = 0; 1674 u8 comp_codes_1g = 0; 1675 u8 comp_codes_10g = 0; 1676 u8 oui_bytes[3] = {0, 0, 0}; 1677 u16 enforce_sfp = 0; 1678 u8 connector = 0; 1679 u8 cable_length = 0; 1680 u8 device_tech = 0; 1681 bool active_cable = false; 1682 1683 if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_fiber_qsfp) { 1684 hw->phy.sfp_type = ixgbe_sfp_type_not_present; 1685 return IXGBE_ERR_SFP_NOT_PRESENT; 1686 } 1687 1688 /* LAN ID is needed for sfp_type determination */ 1689 hw->mac.ops.set_lan_id(hw); 1690 1691 status = hw->phy.ops.read_i2c_eeprom(hw, IXGBE_SFF_IDENTIFIER, 1692 &identifier); 1693 1694 if (status != 0) 1695 goto err_read_i2c_eeprom; 1696 1697 if (identifier != IXGBE_SFF_IDENTIFIER_QSFP_PLUS) { 1698 hw->phy.type = ixgbe_phy_sfp_unsupported; 1699 return IXGBE_ERR_SFP_NOT_SUPPORTED; 1700 } 1701 1702 hw->phy.id = identifier; 1703 1704 status = hw->phy.ops.read_i2c_eeprom(hw, IXGBE_SFF_QSFP_10GBE_COMP, 1705 &comp_codes_10g); 1706 1707 if (status != 0) 1708 goto err_read_i2c_eeprom; 1709 1710 status = hw->phy.ops.read_i2c_eeprom(hw, IXGBE_SFF_QSFP_1GBE_COMP, 1711 &comp_codes_1g); 1712 1713 if (status != 0) 1714 goto err_read_i2c_eeprom; 1715 1716 if (comp_codes_10g & IXGBE_SFF_QSFP_DA_PASSIVE_CABLE) { 1717 hw->phy.type = ixgbe_phy_qsfp_passive_unknown; 1718 if (hw->bus.lan_id == 0) 1719 hw->phy.sfp_type = ixgbe_sfp_type_da_cu_core0; 1720 else 1721 hw->phy.sfp_type = ixgbe_sfp_type_da_cu_core1; 1722 } else if (comp_codes_10g & (IXGBE_SFF_10GBASESR_CAPABLE | 1723 IXGBE_SFF_10GBASELR_CAPABLE)) { 1724 if (hw->bus.lan_id == 0) 1725 hw->phy.sfp_type = ixgbe_sfp_type_srlr_core0; 1726 else 1727 hw->phy.sfp_type = ixgbe_sfp_type_srlr_core1; 1728 } else { 1729 if (comp_codes_10g & IXGBE_SFF_QSFP_DA_ACTIVE_CABLE) 1730 active_cable = true; 1731 1732 if (!active_cable) { 1733 /* check for active DA cables that pre-date 1734 * SFF-8436 v3.6 1735 */ 1736 hw->phy.ops.read_i2c_eeprom(hw, 1737 IXGBE_SFF_QSFP_CONNECTOR, 1738 &connector); 1739 1740 hw->phy.ops.read_i2c_eeprom(hw, 1741 IXGBE_SFF_QSFP_CABLE_LENGTH, 1742 &cable_length); 1743 1744 hw->phy.ops.read_i2c_eeprom(hw, 1745 IXGBE_SFF_QSFP_DEVICE_TECH, 1746 &device_tech); 1747 1748 if ((connector == 1749 IXGBE_SFF_QSFP_CONNECTOR_NOT_SEPARABLE) && 1750 (cable_length > 0) && 1751 ((device_tech >> 4) == 1752 IXGBE_SFF_QSFP_TRANSMITER_850NM_VCSEL)) 1753 active_cable = true; 1754 } 1755 1756 if (active_cable) { 1757 hw->phy.type = ixgbe_phy_qsfp_active_unknown; 1758 if (hw->bus.lan_id == 0) 1759 hw->phy.sfp_type = 1760 ixgbe_sfp_type_da_act_lmt_core0; 1761 else 1762 hw->phy.sfp_type = 1763 ixgbe_sfp_type_da_act_lmt_core1; 1764 } else { 1765 /* unsupported module type */ 1766 hw->phy.type = ixgbe_phy_sfp_unsupported; 1767 return IXGBE_ERR_SFP_NOT_SUPPORTED; 1768 } 1769 } 1770 1771 if (hw->phy.sfp_type != stored_sfp_type) 1772 hw->phy.sfp_setup_needed = true; 1773 1774 /* Determine if the QSFP+ PHY is dual speed or not. */ 1775 hw->phy.multispeed_fiber = false; 1776 if (((comp_codes_1g & IXGBE_SFF_1GBASESX_CAPABLE) && 1777 (comp_codes_10g & IXGBE_SFF_10GBASESR_CAPABLE)) || 1778 ((comp_codes_1g & IXGBE_SFF_1GBASELX_CAPABLE) && 1779 (comp_codes_10g & IXGBE_SFF_10GBASELR_CAPABLE))) 1780 hw->phy.multispeed_fiber = true; 1781 1782 /* Determine PHY vendor for optical modules */ 1783 if (comp_codes_10g & (IXGBE_SFF_10GBASESR_CAPABLE | 1784 IXGBE_SFF_10GBASELR_CAPABLE)) { 1785 status = hw->phy.ops.read_i2c_eeprom(hw, 1786 IXGBE_SFF_QSFP_VENDOR_OUI_BYTE0, 1787 &oui_bytes[0]); 1788 1789 if (status != 0) 1790 goto err_read_i2c_eeprom; 1791 1792 status = hw->phy.ops.read_i2c_eeprom(hw, 1793 IXGBE_SFF_QSFP_VENDOR_OUI_BYTE1, 1794 &oui_bytes[1]); 1795 1796 if (status != 0) 1797 goto err_read_i2c_eeprom; 1798 1799 status = hw->phy.ops.read_i2c_eeprom(hw, 1800 IXGBE_SFF_QSFP_VENDOR_OUI_BYTE2, 1801 &oui_bytes[2]); 1802 1803 if (status != 0) 1804 goto err_read_i2c_eeprom; 1805 1806 vendor_oui = 1807 ((oui_bytes[0] << IXGBE_SFF_VENDOR_OUI_BYTE0_SHIFT) | 1808 (oui_bytes[1] << IXGBE_SFF_VENDOR_OUI_BYTE1_SHIFT) | 1809 (oui_bytes[2] << IXGBE_SFF_VENDOR_OUI_BYTE2_SHIFT)); 1810 1811 if (vendor_oui == IXGBE_SFF_VENDOR_OUI_INTEL) 1812 hw->phy.type = ixgbe_phy_qsfp_intel; 1813 else 1814 hw->phy.type = ixgbe_phy_qsfp_unknown; 1815 1816 hw->mac.ops.get_device_caps(hw, &enforce_sfp); 1817 if (!(enforce_sfp & IXGBE_DEVICE_CAPS_ALLOW_ANY_SFP)) { 1818 /* Make sure we're a supported PHY type */ 1819 if (hw->phy.type == ixgbe_phy_qsfp_intel) 1820 return 0; 1821 if (hw->allow_unsupported_sfp) { 1822 e_warn(drv, "WARNING: Intel (R) Network Connections are quality tested using Intel (R) Ethernet Optics. Using untested modules is not supported and may cause unstable operation or damage to the module or the adapter. Intel Corporation is not responsible for any harm caused by using untested modules.\n"); 1823 return 0; 1824 } 1825 hw_dbg(hw, "QSFP module not supported\n"); 1826 hw->phy.type = ixgbe_phy_sfp_unsupported; 1827 return IXGBE_ERR_SFP_NOT_SUPPORTED; 1828 } 1829 return 0; 1830 } 1831 return 0; 1832 1833 err_read_i2c_eeprom: 1834 hw->phy.sfp_type = ixgbe_sfp_type_not_present; 1835 hw->phy.id = 0; 1836 hw->phy.type = ixgbe_phy_unknown; 1837 1838 return IXGBE_ERR_SFP_NOT_PRESENT; 1839 } 1840 1841 /** 1842 * ixgbe_get_sfp_init_sequence_offsets - Provides offset of PHY init sequence 1843 * @hw: pointer to hardware structure 1844 * @list_offset: offset to the SFP ID list 1845 * @data_offset: offset to the SFP data block 1846 * 1847 * Checks the MAC's EEPROM to see if it supports a given SFP+ module type, if 1848 * so it returns the offsets to the phy init sequence block. 1849 **/ 1850 s32 ixgbe_get_sfp_init_sequence_offsets(struct ixgbe_hw *hw, 1851 u16 *list_offset, 1852 u16 *data_offset) 1853 { 1854 u16 sfp_id; 1855 u16 sfp_type = hw->phy.sfp_type; 1856 1857 if (hw->phy.sfp_type == ixgbe_sfp_type_unknown) 1858 return IXGBE_ERR_SFP_NOT_SUPPORTED; 1859 1860 if (hw->phy.sfp_type == ixgbe_sfp_type_not_present) 1861 return IXGBE_ERR_SFP_NOT_PRESENT; 1862 1863 if ((hw->device_id == IXGBE_DEV_ID_82598_SR_DUAL_PORT_EM) && 1864 (hw->phy.sfp_type == ixgbe_sfp_type_da_cu)) 1865 return IXGBE_ERR_SFP_NOT_SUPPORTED; 1866 1867 /* 1868 * Limiting active cables and 1G Phys must be initialized as 1869 * SR modules 1870 */ 1871 if (sfp_type == ixgbe_sfp_type_da_act_lmt_core0 || 1872 sfp_type == ixgbe_sfp_type_1g_lx_core0 || 1873 sfp_type == ixgbe_sfp_type_1g_cu_core0 || 1874 sfp_type == ixgbe_sfp_type_1g_sx_core0) 1875 sfp_type = ixgbe_sfp_type_srlr_core0; 1876 else if (sfp_type == ixgbe_sfp_type_da_act_lmt_core1 || 1877 sfp_type == ixgbe_sfp_type_1g_lx_core1 || 1878 sfp_type == ixgbe_sfp_type_1g_cu_core1 || 1879 sfp_type == ixgbe_sfp_type_1g_sx_core1) 1880 sfp_type = ixgbe_sfp_type_srlr_core1; 1881 1882 /* Read offset to PHY init contents */ 1883 if (hw->eeprom.ops.read(hw, IXGBE_PHY_INIT_OFFSET_NL, list_offset)) { 1884 hw_err(hw, "eeprom read at %d failed\n", 1885 IXGBE_PHY_INIT_OFFSET_NL); 1886 return IXGBE_ERR_SFP_NO_INIT_SEQ_PRESENT; 1887 } 1888 1889 if ((!*list_offset) || (*list_offset == 0xFFFF)) 1890 return IXGBE_ERR_SFP_NO_INIT_SEQ_PRESENT; 1891 1892 /* Shift offset to first ID word */ 1893 (*list_offset)++; 1894 1895 /* 1896 * Find the matching SFP ID in the EEPROM 1897 * and program the init sequence 1898 */ 1899 if (hw->eeprom.ops.read(hw, *list_offset, &sfp_id)) 1900 goto err_phy; 1901 1902 while (sfp_id != IXGBE_PHY_INIT_END_NL) { 1903 if (sfp_id == sfp_type) { 1904 (*list_offset)++; 1905 if (hw->eeprom.ops.read(hw, *list_offset, data_offset)) 1906 goto err_phy; 1907 if ((!*data_offset) || (*data_offset == 0xFFFF)) { 1908 hw_dbg(hw, "SFP+ module not supported\n"); 1909 return IXGBE_ERR_SFP_NOT_SUPPORTED; 1910 } else { 1911 break; 1912 } 1913 } else { 1914 (*list_offset) += 2; 1915 if (hw->eeprom.ops.read(hw, *list_offset, &sfp_id)) 1916 goto err_phy; 1917 } 1918 } 1919 1920 if (sfp_id == IXGBE_PHY_INIT_END_NL) { 1921 hw_dbg(hw, "No matching SFP+ module found\n"); 1922 return IXGBE_ERR_SFP_NOT_SUPPORTED; 1923 } 1924 1925 return 0; 1926 1927 err_phy: 1928 hw_err(hw, "eeprom read at offset %d failed\n", *list_offset); 1929 return IXGBE_ERR_PHY; 1930 } 1931 1932 /** 1933 * ixgbe_read_i2c_eeprom_generic - Reads 8 bit EEPROM word over I2C interface 1934 * @hw: pointer to hardware structure 1935 * @byte_offset: EEPROM byte offset to read 1936 * @eeprom_data: value read 1937 * 1938 * Performs byte read operation to SFP module's EEPROM over I2C interface. 1939 **/ 1940 s32 ixgbe_read_i2c_eeprom_generic(struct ixgbe_hw *hw, u8 byte_offset, 1941 u8 *eeprom_data) 1942 { 1943 return hw->phy.ops.read_i2c_byte(hw, byte_offset, 1944 IXGBE_I2C_EEPROM_DEV_ADDR, 1945 eeprom_data); 1946 } 1947 1948 /** 1949 * ixgbe_read_i2c_sff8472_generic - Reads 8 bit word over I2C interface 1950 * @hw: pointer to hardware structure 1951 * @byte_offset: byte offset at address 0xA2 1952 * @sff8472_data: value read 1953 * 1954 * Performs byte read operation to SFP module's SFF-8472 data over I2C 1955 **/ 1956 s32 ixgbe_read_i2c_sff8472_generic(struct ixgbe_hw *hw, u8 byte_offset, 1957 u8 *sff8472_data) 1958 { 1959 return hw->phy.ops.read_i2c_byte(hw, byte_offset, 1960 IXGBE_I2C_EEPROM_DEV_ADDR2, 1961 sff8472_data); 1962 } 1963 1964 /** 1965 * ixgbe_write_i2c_eeprom_generic - Writes 8 bit EEPROM word over I2C interface 1966 * @hw: pointer to hardware structure 1967 * @byte_offset: EEPROM byte offset to write 1968 * @eeprom_data: value to write 1969 * 1970 * Performs byte write operation to SFP module's EEPROM over I2C interface. 1971 **/ 1972 s32 ixgbe_write_i2c_eeprom_generic(struct ixgbe_hw *hw, u8 byte_offset, 1973 u8 eeprom_data) 1974 { 1975 return hw->phy.ops.write_i2c_byte(hw, byte_offset, 1976 IXGBE_I2C_EEPROM_DEV_ADDR, 1977 eeprom_data); 1978 } 1979 1980 /** 1981 * ixgbe_is_sfp_probe - Returns true if SFP is being detected 1982 * @hw: pointer to hardware structure 1983 * @offset: eeprom offset to be read 1984 * @addr: I2C address to be read 1985 */ 1986 static bool ixgbe_is_sfp_probe(struct ixgbe_hw *hw, u8 offset, u8 addr) 1987 { 1988 if (addr == IXGBE_I2C_EEPROM_DEV_ADDR && 1989 offset == IXGBE_SFF_IDENTIFIER && 1990 hw->phy.sfp_type == ixgbe_sfp_type_not_present) 1991 return true; 1992 return false; 1993 } 1994 1995 /** 1996 * ixgbe_read_i2c_byte_generic_int - Reads 8 bit word over I2C 1997 * @hw: pointer to hardware structure 1998 * @byte_offset: byte offset to read 1999 * @dev_addr: device address 2000 * @data: value read 2001 * @lock: true if to take and release semaphore 2002 * 2003 * Performs byte read operation to SFP module's EEPROM over I2C interface at 2004 * a specified device address. 2005 */ 2006 static s32 ixgbe_read_i2c_byte_generic_int(struct ixgbe_hw *hw, u8 byte_offset, 2007 u8 dev_addr, u8 *data, bool lock) 2008 { 2009 s32 status; 2010 u32 max_retry = 10; 2011 u32 retry = 0; 2012 u32 swfw_mask = hw->phy.phy_semaphore_mask; 2013 bool nack = true; 2014 2015 if (hw->mac.type >= ixgbe_mac_X550) 2016 max_retry = 3; 2017 if (ixgbe_is_sfp_probe(hw, byte_offset, dev_addr)) 2018 max_retry = IXGBE_SFP_DETECT_RETRIES; 2019 2020 *data = 0; 2021 2022 do { 2023 if (lock && hw->mac.ops.acquire_swfw_sync(hw, swfw_mask)) 2024 return IXGBE_ERR_SWFW_SYNC; 2025 2026 ixgbe_i2c_start(hw); 2027 2028 /* Device Address and write indication */ 2029 status = ixgbe_clock_out_i2c_byte(hw, dev_addr); 2030 if (status != 0) 2031 goto fail; 2032 2033 status = ixgbe_get_i2c_ack(hw); 2034 if (status != 0) 2035 goto fail; 2036 2037 status = ixgbe_clock_out_i2c_byte(hw, byte_offset); 2038 if (status != 0) 2039 goto fail; 2040 2041 status = ixgbe_get_i2c_ack(hw); 2042 if (status != 0) 2043 goto fail; 2044 2045 ixgbe_i2c_start(hw); 2046 2047 /* Device Address and read indication */ 2048 status = ixgbe_clock_out_i2c_byte(hw, (dev_addr | 0x1)); 2049 if (status != 0) 2050 goto fail; 2051 2052 status = ixgbe_get_i2c_ack(hw); 2053 if (status != 0) 2054 goto fail; 2055 2056 status = ixgbe_clock_in_i2c_byte(hw, data); 2057 if (status != 0) 2058 goto fail; 2059 2060 status = ixgbe_clock_out_i2c_bit(hw, nack); 2061 if (status != 0) 2062 goto fail; 2063 2064 ixgbe_i2c_stop(hw); 2065 if (lock) 2066 hw->mac.ops.release_swfw_sync(hw, swfw_mask); 2067 return 0; 2068 2069 fail: 2070 ixgbe_i2c_bus_clear(hw); 2071 if (lock) { 2072 hw->mac.ops.release_swfw_sync(hw, swfw_mask); 2073 msleep(100); 2074 } 2075 retry++; 2076 if (retry < max_retry) 2077 hw_dbg(hw, "I2C byte read error - Retrying.\n"); 2078 else 2079 hw_dbg(hw, "I2C byte read error.\n"); 2080 2081 } while (retry < max_retry); 2082 2083 return status; 2084 } 2085 2086 /** 2087 * ixgbe_read_i2c_byte_generic - Reads 8 bit word over I2C 2088 * @hw: pointer to hardware structure 2089 * @byte_offset: byte offset to read 2090 * @dev_addr: device address 2091 * @data: value read 2092 * 2093 * Performs byte read operation to SFP module's EEPROM over I2C interface at 2094 * a specified device address. 2095 */ 2096 s32 ixgbe_read_i2c_byte_generic(struct ixgbe_hw *hw, u8 byte_offset, 2097 u8 dev_addr, u8 *data) 2098 { 2099 return ixgbe_read_i2c_byte_generic_int(hw, byte_offset, dev_addr, 2100 data, true); 2101 } 2102 2103 /** 2104 * ixgbe_read_i2c_byte_generic_unlocked - Reads 8 bit word over I2C 2105 * @hw: pointer to hardware structure 2106 * @byte_offset: byte offset to read 2107 * @dev_addr: device address 2108 * @data: value read 2109 * 2110 * Performs byte read operation to SFP module's EEPROM over I2C interface at 2111 * a specified device address. 2112 */ 2113 s32 ixgbe_read_i2c_byte_generic_unlocked(struct ixgbe_hw *hw, u8 byte_offset, 2114 u8 dev_addr, u8 *data) 2115 { 2116 return ixgbe_read_i2c_byte_generic_int(hw, byte_offset, dev_addr, 2117 data, false); 2118 } 2119 2120 /** 2121 * ixgbe_write_i2c_byte_generic_int - Writes 8 bit word over I2C 2122 * @hw: pointer to hardware structure 2123 * @byte_offset: byte offset to write 2124 * @dev_addr: device address 2125 * @data: value to write 2126 * @lock: true if to take and release semaphore 2127 * 2128 * Performs byte write operation to SFP module's EEPROM over I2C interface at 2129 * a specified device address. 2130 */ 2131 static s32 ixgbe_write_i2c_byte_generic_int(struct ixgbe_hw *hw, u8 byte_offset, 2132 u8 dev_addr, u8 data, bool lock) 2133 { 2134 s32 status; 2135 u32 max_retry = 1; 2136 u32 retry = 0; 2137 u32 swfw_mask = hw->phy.phy_semaphore_mask; 2138 2139 if (lock && hw->mac.ops.acquire_swfw_sync(hw, swfw_mask)) 2140 return IXGBE_ERR_SWFW_SYNC; 2141 2142 do { 2143 ixgbe_i2c_start(hw); 2144 2145 status = ixgbe_clock_out_i2c_byte(hw, dev_addr); 2146 if (status != 0) 2147 goto fail; 2148 2149 status = ixgbe_get_i2c_ack(hw); 2150 if (status != 0) 2151 goto fail; 2152 2153 status = ixgbe_clock_out_i2c_byte(hw, byte_offset); 2154 if (status != 0) 2155 goto fail; 2156 2157 status = ixgbe_get_i2c_ack(hw); 2158 if (status != 0) 2159 goto fail; 2160 2161 status = ixgbe_clock_out_i2c_byte(hw, data); 2162 if (status != 0) 2163 goto fail; 2164 2165 status = ixgbe_get_i2c_ack(hw); 2166 if (status != 0) 2167 goto fail; 2168 2169 ixgbe_i2c_stop(hw); 2170 if (lock) 2171 hw->mac.ops.release_swfw_sync(hw, swfw_mask); 2172 return 0; 2173 2174 fail: 2175 ixgbe_i2c_bus_clear(hw); 2176 retry++; 2177 if (retry < max_retry) 2178 hw_dbg(hw, "I2C byte write error - Retrying.\n"); 2179 else 2180 hw_dbg(hw, "I2C byte write error.\n"); 2181 } while (retry < max_retry); 2182 2183 if (lock) 2184 hw->mac.ops.release_swfw_sync(hw, swfw_mask); 2185 2186 return status; 2187 } 2188 2189 /** 2190 * ixgbe_write_i2c_byte_generic - Writes 8 bit word over I2C 2191 * @hw: pointer to hardware structure 2192 * @byte_offset: byte offset to write 2193 * @dev_addr: device address 2194 * @data: value to write 2195 * 2196 * Performs byte write operation to SFP module's EEPROM over I2C interface at 2197 * a specified device address. 2198 */ 2199 s32 ixgbe_write_i2c_byte_generic(struct ixgbe_hw *hw, u8 byte_offset, 2200 u8 dev_addr, u8 data) 2201 { 2202 return ixgbe_write_i2c_byte_generic_int(hw, byte_offset, dev_addr, 2203 data, true); 2204 } 2205 2206 /** 2207 * ixgbe_write_i2c_byte_generic_unlocked - Writes 8 bit word over I2C 2208 * @hw: pointer to hardware structure 2209 * @byte_offset: byte offset to write 2210 * @dev_addr: device address 2211 * @data: value to write 2212 * 2213 * Performs byte write operation to SFP module's EEPROM over I2C interface at 2214 * a specified device address. 2215 */ 2216 s32 ixgbe_write_i2c_byte_generic_unlocked(struct ixgbe_hw *hw, u8 byte_offset, 2217 u8 dev_addr, u8 data) 2218 { 2219 return ixgbe_write_i2c_byte_generic_int(hw, byte_offset, dev_addr, 2220 data, false); 2221 } 2222 2223 /** 2224 * ixgbe_i2c_start - Sets I2C start condition 2225 * @hw: pointer to hardware structure 2226 * 2227 * Sets I2C start condition (High -> Low on SDA while SCL is High) 2228 * Set bit-bang mode on X550 hardware. 2229 **/ 2230 static void ixgbe_i2c_start(struct ixgbe_hw *hw) 2231 { 2232 u32 i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL(hw)); 2233 2234 i2cctl |= IXGBE_I2C_BB_EN(hw); 2235 2236 /* Start condition must begin with data and clock high */ 2237 ixgbe_set_i2c_data(hw, &i2cctl, 1); 2238 ixgbe_raise_i2c_clk(hw, &i2cctl); 2239 2240 /* Setup time for start condition (4.7us) */ 2241 udelay(IXGBE_I2C_T_SU_STA); 2242 2243 ixgbe_set_i2c_data(hw, &i2cctl, 0); 2244 2245 /* Hold time for start condition (4us) */ 2246 udelay(IXGBE_I2C_T_HD_STA); 2247 2248 ixgbe_lower_i2c_clk(hw, &i2cctl); 2249 2250 /* Minimum low period of clock is 4.7 us */ 2251 udelay(IXGBE_I2C_T_LOW); 2252 2253 } 2254 2255 /** 2256 * ixgbe_i2c_stop - Sets I2C stop condition 2257 * @hw: pointer to hardware structure 2258 * 2259 * Sets I2C stop condition (Low -> High on SDA while SCL is High) 2260 * Disables bit-bang mode and negates data output enable on X550 2261 * hardware. 2262 **/ 2263 static void ixgbe_i2c_stop(struct ixgbe_hw *hw) 2264 { 2265 u32 i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL(hw)); 2266 u32 data_oe_bit = IXGBE_I2C_DATA_OE_N_EN(hw); 2267 u32 clk_oe_bit = IXGBE_I2C_CLK_OE_N_EN(hw); 2268 u32 bb_en_bit = IXGBE_I2C_BB_EN(hw); 2269 2270 /* Stop condition must begin with data low and clock high */ 2271 ixgbe_set_i2c_data(hw, &i2cctl, 0); 2272 ixgbe_raise_i2c_clk(hw, &i2cctl); 2273 2274 /* Setup time for stop condition (4us) */ 2275 udelay(IXGBE_I2C_T_SU_STO); 2276 2277 ixgbe_set_i2c_data(hw, &i2cctl, 1); 2278 2279 /* bus free time between stop and start (4.7us)*/ 2280 udelay(IXGBE_I2C_T_BUF); 2281 2282 if (bb_en_bit || data_oe_bit || clk_oe_bit) { 2283 i2cctl &= ~bb_en_bit; 2284 i2cctl |= data_oe_bit | clk_oe_bit; 2285 IXGBE_WRITE_REG(hw, IXGBE_I2CCTL(hw), i2cctl); 2286 IXGBE_WRITE_FLUSH(hw); 2287 } 2288 } 2289 2290 /** 2291 * ixgbe_clock_in_i2c_byte - Clocks in one byte via I2C 2292 * @hw: pointer to hardware structure 2293 * @data: data byte to clock in 2294 * 2295 * Clocks in one byte data via I2C data/clock 2296 **/ 2297 static s32 ixgbe_clock_in_i2c_byte(struct ixgbe_hw *hw, u8 *data) 2298 { 2299 s32 i; 2300 bool bit = false; 2301 2302 *data = 0; 2303 for (i = 7; i >= 0; i--) { 2304 ixgbe_clock_in_i2c_bit(hw, &bit); 2305 *data |= bit << i; 2306 } 2307 2308 return 0; 2309 } 2310 2311 /** 2312 * ixgbe_clock_out_i2c_byte - Clocks out one byte via I2C 2313 * @hw: pointer to hardware structure 2314 * @data: data byte clocked out 2315 * 2316 * Clocks out one byte data via I2C data/clock 2317 **/ 2318 static s32 ixgbe_clock_out_i2c_byte(struct ixgbe_hw *hw, u8 data) 2319 { 2320 s32 status; 2321 s32 i; 2322 u32 i2cctl; 2323 bool bit = false; 2324 2325 for (i = 7; i >= 0; i--) { 2326 bit = (data >> i) & 0x1; 2327 status = ixgbe_clock_out_i2c_bit(hw, bit); 2328 2329 if (status != 0) 2330 break; 2331 } 2332 2333 /* Release SDA line (set high) */ 2334 i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL(hw)); 2335 i2cctl |= IXGBE_I2C_DATA_OUT(hw); 2336 i2cctl |= IXGBE_I2C_DATA_OE_N_EN(hw); 2337 IXGBE_WRITE_REG(hw, IXGBE_I2CCTL(hw), i2cctl); 2338 IXGBE_WRITE_FLUSH(hw); 2339 2340 return status; 2341 } 2342 2343 /** 2344 * ixgbe_get_i2c_ack - Polls for I2C ACK 2345 * @hw: pointer to hardware structure 2346 * 2347 * Clocks in/out one bit via I2C data/clock 2348 **/ 2349 static s32 ixgbe_get_i2c_ack(struct ixgbe_hw *hw) 2350 { 2351 u32 data_oe_bit = IXGBE_I2C_DATA_OE_N_EN(hw); 2352 s32 status = 0; 2353 u32 i = 0; 2354 u32 i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL(hw)); 2355 u32 timeout = 10; 2356 bool ack = true; 2357 2358 if (data_oe_bit) { 2359 i2cctl |= IXGBE_I2C_DATA_OUT(hw); 2360 i2cctl |= data_oe_bit; 2361 IXGBE_WRITE_REG(hw, IXGBE_I2CCTL(hw), i2cctl); 2362 IXGBE_WRITE_FLUSH(hw); 2363 } 2364 ixgbe_raise_i2c_clk(hw, &i2cctl); 2365 2366 /* Minimum high period of clock is 4us */ 2367 udelay(IXGBE_I2C_T_HIGH); 2368 2369 /* Poll for ACK. Note that ACK in I2C spec is 2370 * transition from 1 to 0 */ 2371 for (i = 0; i < timeout; i++) { 2372 i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL(hw)); 2373 ack = ixgbe_get_i2c_data(hw, &i2cctl); 2374 2375 udelay(1); 2376 if (ack == 0) 2377 break; 2378 } 2379 2380 if (ack == 1) { 2381 hw_dbg(hw, "I2C ack was not received.\n"); 2382 status = IXGBE_ERR_I2C; 2383 } 2384 2385 ixgbe_lower_i2c_clk(hw, &i2cctl); 2386 2387 /* Minimum low period of clock is 4.7 us */ 2388 udelay(IXGBE_I2C_T_LOW); 2389 2390 return status; 2391 } 2392 2393 /** 2394 * ixgbe_clock_in_i2c_bit - Clocks in one bit via I2C data/clock 2395 * @hw: pointer to hardware structure 2396 * @data: read data value 2397 * 2398 * Clocks in one bit via I2C data/clock 2399 **/ 2400 static s32 ixgbe_clock_in_i2c_bit(struct ixgbe_hw *hw, bool *data) 2401 { 2402 u32 i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL(hw)); 2403 u32 data_oe_bit = IXGBE_I2C_DATA_OE_N_EN(hw); 2404 2405 if (data_oe_bit) { 2406 i2cctl |= IXGBE_I2C_DATA_OUT(hw); 2407 i2cctl |= data_oe_bit; 2408 IXGBE_WRITE_REG(hw, IXGBE_I2CCTL(hw), i2cctl); 2409 IXGBE_WRITE_FLUSH(hw); 2410 } 2411 ixgbe_raise_i2c_clk(hw, &i2cctl); 2412 2413 /* Minimum high period of clock is 4us */ 2414 udelay(IXGBE_I2C_T_HIGH); 2415 2416 i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL(hw)); 2417 *data = ixgbe_get_i2c_data(hw, &i2cctl); 2418 2419 ixgbe_lower_i2c_clk(hw, &i2cctl); 2420 2421 /* Minimum low period of clock is 4.7 us */ 2422 udelay(IXGBE_I2C_T_LOW); 2423 2424 return 0; 2425 } 2426 2427 /** 2428 * ixgbe_clock_out_i2c_bit - Clocks in/out one bit via I2C data/clock 2429 * @hw: pointer to hardware structure 2430 * @data: data value to write 2431 * 2432 * Clocks out one bit via I2C data/clock 2433 **/ 2434 static s32 ixgbe_clock_out_i2c_bit(struct ixgbe_hw *hw, bool data) 2435 { 2436 s32 status; 2437 u32 i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL(hw)); 2438 2439 status = ixgbe_set_i2c_data(hw, &i2cctl, data); 2440 if (status == 0) { 2441 ixgbe_raise_i2c_clk(hw, &i2cctl); 2442 2443 /* Minimum high period of clock is 4us */ 2444 udelay(IXGBE_I2C_T_HIGH); 2445 2446 ixgbe_lower_i2c_clk(hw, &i2cctl); 2447 2448 /* Minimum low period of clock is 4.7 us. 2449 * This also takes care of the data hold time. 2450 */ 2451 udelay(IXGBE_I2C_T_LOW); 2452 } else { 2453 hw_dbg(hw, "I2C data was not set to %X\n", data); 2454 return IXGBE_ERR_I2C; 2455 } 2456 2457 return 0; 2458 } 2459 /** 2460 * ixgbe_raise_i2c_clk - Raises the I2C SCL clock 2461 * @hw: pointer to hardware structure 2462 * @i2cctl: Current value of I2CCTL register 2463 * 2464 * Raises the I2C clock line '0'->'1' 2465 * Negates the I2C clock output enable on X550 hardware. 2466 **/ 2467 static void ixgbe_raise_i2c_clk(struct ixgbe_hw *hw, u32 *i2cctl) 2468 { 2469 u32 clk_oe_bit = IXGBE_I2C_CLK_OE_N_EN(hw); 2470 u32 i = 0; 2471 u32 timeout = IXGBE_I2C_CLOCK_STRETCHING_TIMEOUT; 2472 u32 i2cctl_r = 0; 2473 2474 if (clk_oe_bit) { 2475 *i2cctl |= clk_oe_bit; 2476 IXGBE_WRITE_REG(hw, IXGBE_I2CCTL(hw), *i2cctl); 2477 } 2478 2479 for (i = 0; i < timeout; i++) { 2480 *i2cctl |= IXGBE_I2C_CLK_OUT(hw); 2481 IXGBE_WRITE_REG(hw, IXGBE_I2CCTL(hw), *i2cctl); 2482 IXGBE_WRITE_FLUSH(hw); 2483 /* SCL rise time (1000ns) */ 2484 udelay(IXGBE_I2C_T_RISE); 2485 2486 i2cctl_r = IXGBE_READ_REG(hw, IXGBE_I2CCTL(hw)); 2487 if (i2cctl_r & IXGBE_I2C_CLK_IN(hw)) 2488 break; 2489 } 2490 } 2491 2492 /** 2493 * ixgbe_lower_i2c_clk - Lowers the I2C SCL clock 2494 * @hw: pointer to hardware structure 2495 * @i2cctl: Current value of I2CCTL register 2496 * 2497 * Lowers the I2C clock line '1'->'0' 2498 * Asserts the I2C clock output enable on X550 hardware. 2499 **/ 2500 static void ixgbe_lower_i2c_clk(struct ixgbe_hw *hw, u32 *i2cctl) 2501 { 2502 2503 *i2cctl &= ~IXGBE_I2C_CLK_OUT(hw); 2504 *i2cctl &= ~IXGBE_I2C_CLK_OE_N_EN(hw); 2505 2506 IXGBE_WRITE_REG(hw, IXGBE_I2CCTL(hw), *i2cctl); 2507 IXGBE_WRITE_FLUSH(hw); 2508 2509 /* SCL fall time (300ns) */ 2510 udelay(IXGBE_I2C_T_FALL); 2511 } 2512 2513 /** 2514 * ixgbe_set_i2c_data - Sets the I2C data bit 2515 * @hw: pointer to hardware structure 2516 * @i2cctl: Current value of I2CCTL register 2517 * @data: I2C data value (0 or 1) to set 2518 * 2519 * Sets the I2C data bit 2520 * Asserts the I2C data output enable on X550 hardware. 2521 **/ 2522 static s32 ixgbe_set_i2c_data(struct ixgbe_hw *hw, u32 *i2cctl, bool data) 2523 { 2524 u32 data_oe_bit = IXGBE_I2C_DATA_OE_N_EN(hw); 2525 2526 if (data) 2527 *i2cctl |= IXGBE_I2C_DATA_OUT(hw); 2528 else 2529 *i2cctl &= ~IXGBE_I2C_DATA_OUT(hw); 2530 *i2cctl &= ~data_oe_bit; 2531 2532 IXGBE_WRITE_REG(hw, IXGBE_I2CCTL(hw), *i2cctl); 2533 IXGBE_WRITE_FLUSH(hw); 2534 2535 /* Data rise/fall (1000ns/300ns) and set-up time (250ns) */ 2536 udelay(IXGBE_I2C_T_RISE + IXGBE_I2C_T_FALL + IXGBE_I2C_T_SU_DATA); 2537 2538 if (!data) /* Can't verify data in this case */ 2539 return 0; 2540 if (data_oe_bit) { 2541 *i2cctl |= data_oe_bit; 2542 IXGBE_WRITE_REG(hw, IXGBE_I2CCTL(hw), *i2cctl); 2543 IXGBE_WRITE_FLUSH(hw); 2544 } 2545 2546 /* Verify data was set correctly */ 2547 *i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL(hw)); 2548 if (data != ixgbe_get_i2c_data(hw, i2cctl)) { 2549 hw_dbg(hw, "Error - I2C data was not set to %X.\n", data); 2550 return IXGBE_ERR_I2C; 2551 } 2552 2553 return 0; 2554 } 2555 2556 /** 2557 * ixgbe_get_i2c_data - Reads the I2C SDA data bit 2558 * @hw: pointer to hardware structure 2559 * @i2cctl: Current value of I2CCTL register 2560 * 2561 * Returns the I2C data bit value 2562 * Negates the I2C data output enable on X550 hardware. 2563 **/ 2564 static bool ixgbe_get_i2c_data(struct ixgbe_hw *hw, u32 *i2cctl) 2565 { 2566 u32 data_oe_bit = IXGBE_I2C_DATA_OE_N_EN(hw); 2567 2568 if (data_oe_bit) { 2569 *i2cctl |= data_oe_bit; 2570 IXGBE_WRITE_REG(hw, IXGBE_I2CCTL(hw), *i2cctl); 2571 IXGBE_WRITE_FLUSH(hw); 2572 udelay(IXGBE_I2C_T_FALL); 2573 } 2574 2575 if (*i2cctl & IXGBE_I2C_DATA_IN(hw)) 2576 return true; 2577 return false; 2578 } 2579 2580 /** 2581 * ixgbe_i2c_bus_clear - Clears the I2C bus 2582 * @hw: pointer to hardware structure 2583 * 2584 * Clears the I2C bus by sending nine clock pulses. 2585 * Used when data line is stuck low. 2586 **/ 2587 static void ixgbe_i2c_bus_clear(struct ixgbe_hw *hw) 2588 { 2589 u32 i2cctl; 2590 u32 i; 2591 2592 ixgbe_i2c_start(hw); 2593 i2cctl = IXGBE_READ_REG(hw, IXGBE_I2CCTL(hw)); 2594 2595 ixgbe_set_i2c_data(hw, &i2cctl, 1); 2596 2597 for (i = 0; i < 9; i++) { 2598 ixgbe_raise_i2c_clk(hw, &i2cctl); 2599 2600 /* Min high period of clock is 4us */ 2601 udelay(IXGBE_I2C_T_HIGH); 2602 2603 ixgbe_lower_i2c_clk(hw, &i2cctl); 2604 2605 /* Min low period of clock is 4.7us*/ 2606 udelay(IXGBE_I2C_T_LOW); 2607 } 2608 2609 ixgbe_i2c_start(hw); 2610 2611 /* Put the i2c bus back to default state */ 2612 ixgbe_i2c_stop(hw); 2613 } 2614 2615 /** 2616 * ixgbe_tn_check_overtemp - Checks if an overtemp occurred. 2617 * @hw: pointer to hardware structure 2618 * 2619 * Checks if the LASI temp alarm status was triggered due to overtemp 2620 **/ 2621 s32 ixgbe_tn_check_overtemp(struct ixgbe_hw *hw) 2622 { 2623 u16 phy_data = 0; 2624 2625 if (hw->device_id != IXGBE_DEV_ID_82599_T3_LOM) 2626 return 0; 2627 2628 /* Check that the LASI temp alarm status was triggered */ 2629 hw->phy.ops.read_reg(hw, IXGBE_TN_LASI_STATUS_REG, 2630 MDIO_MMD_PMAPMD, &phy_data); 2631 2632 if (!(phy_data & IXGBE_TN_LASI_STATUS_TEMP_ALARM)) 2633 return 0; 2634 2635 return IXGBE_ERR_OVERTEMP; 2636 } 2637 2638 /** ixgbe_set_copper_phy_power - Control power for copper phy 2639 * @hw: pointer to hardware structure 2640 * @on: true for on, false for off 2641 **/ 2642 s32 ixgbe_set_copper_phy_power(struct ixgbe_hw *hw, bool on) 2643 { 2644 u32 status; 2645 u16 reg; 2646 2647 /* Bail if we don't have copper phy */ 2648 if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_copper) 2649 return 0; 2650 2651 if (!on && ixgbe_mng_present(hw)) 2652 return 0; 2653 2654 status = hw->phy.ops.read_reg(hw, MDIO_CTRL1, MDIO_MMD_VEND1, ®); 2655 if (status) 2656 return status; 2657 2658 if (on) { 2659 reg &= ~IXGBE_MDIO_PHY_SET_LOW_POWER_MODE; 2660 } else { 2661 if (ixgbe_check_reset_blocked(hw)) 2662 return 0; 2663 reg |= IXGBE_MDIO_PHY_SET_LOW_POWER_MODE; 2664 } 2665 2666 status = hw->phy.ops.write_reg(hw, MDIO_CTRL1, MDIO_MMD_VEND1, reg); 2667 return status; 2668 } 2669