1 // SPDX-License-Identifier: GPL-2.0 2 /* Copyright (c) 2018 Intel Corporation */ 3 4 #include <linux/delay.h> 5 6 #include "igc_hw.h" 7 #include "igc_i225.h" 8 #include "igc_mac.h" 9 #include "igc_base.h" 10 #include "igc.h" 11 12 /** 13 * igc_reset_hw_base - Reset hardware 14 * @hw: pointer to the HW structure 15 * 16 * This resets the hardware into a known state. This is a 17 * function pointer entry point called by the api module. 18 */ 19 static s32 igc_reset_hw_base(struct igc_hw *hw) 20 { 21 s32 ret_val; 22 u32 ctrl; 23 24 /* Prevent the PCI-E bus from sticking if there is no TLP connection 25 * on the last TLP read/write transaction when MAC is reset. 26 */ 27 ret_val = igc_disable_pcie_master(hw); 28 if (ret_val) 29 hw_dbg("PCI-E Master disable polling has failed.\n"); 30 31 hw_dbg("Masking off all interrupts\n"); 32 wr32(IGC_IMC, 0xffffffff); 33 34 wr32(IGC_RCTL, 0); 35 wr32(IGC_TCTL, IGC_TCTL_PSP); 36 wrfl(); 37 38 usleep_range(10000, 20000); 39 40 ctrl = rd32(IGC_CTRL); 41 42 hw_dbg("Issuing a global reset to MAC\n"); 43 wr32(IGC_CTRL, ctrl | IGC_CTRL_DEV_RST); 44 45 ret_val = igc_get_auto_rd_done(hw); 46 if (ret_val) { 47 /* When auto config read does not complete, do not 48 * return with an error. This can happen in situations 49 * where there is no eeprom and prevents getting link. 50 */ 51 hw_dbg("Auto Read Done did not complete\n"); 52 } 53 54 /* Clear any pending interrupt events. */ 55 wr32(IGC_IMC, 0xffffffff); 56 rd32(IGC_ICR); 57 58 return ret_val; 59 } 60 61 /** 62 * igc_init_nvm_params_base - Init NVM func ptrs. 63 * @hw: pointer to the HW structure 64 */ 65 static s32 igc_init_nvm_params_base(struct igc_hw *hw) 66 { 67 struct igc_nvm_info *nvm = &hw->nvm; 68 u32 eecd = rd32(IGC_EECD); 69 u16 size; 70 71 size = (u16)((eecd & IGC_EECD_SIZE_EX_MASK) >> 72 IGC_EECD_SIZE_EX_SHIFT); 73 74 /* Added to a constant, "size" becomes the left-shift value 75 * for setting word_size. 76 */ 77 size += NVM_WORD_SIZE_BASE_SHIFT; 78 79 /* Just in case size is out of range, cap it to the largest 80 * EEPROM size supported 81 */ 82 if (size > 15) 83 size = 15; 84 85 nvm->type = igc_nvm_eeprom_spi; 86 nvm->word_size = BIT(size); 87 nvm->opcode_bits = 8; 88 nvm->delay_usec = 1; 89 90 nvm->page_size = eecd & IGC_EECD_ADDR_BITS ? 32 : 8; 91 nvm->address_bits = eecd & IGC_EECD_ADDR_BITS ? 92 16 : 8; 93 94 if (nvm->word_size == BIT(15)) 95 nvm->page_size = 128; 96 97 return 0; 98 } 99 100 /** 101 * igc_setup_copper_link_base - Configure copper link settings 102 * @hw: pointer to the HW structure 103 * 104 * Configures the link for auto-neg or forced speed and duplex. Then we check 105 * for link, once link is established calls to configure collision distance 106 * and flow control are called. 107 */ 108 static s32 igc_setup_copper_link_base(struct igc_hw *hw) 109 { 110 s32 ret_val = 0; 111 u32 ctrl; 112 113 ctrl = rd32(IGC_CTRL); 114 ctrl |= IGC_CTRL_SLU; 115 ctrl &= ~(IGC_CTRL_FRCSPD | IGC_CTRL_FRCDPX); 116 wr32(IGC_CTRL, ctrl); 117 118 ret_val = igc_setup_copper_link(hw); 119 120 return ret_val; 121 } 122 123 /** 124 * igc_init_mac_params_base - Init MAC func ptrs. 125 * @hw: pointer to the HW structure 126 */ 127 static s32 igc_init_mac_params_base(struct igc_hw *hw) 128 { 129 struct igc_dev_spec_base *dev_spec = &hw->dev_spec._base; 130 struct igc_mac_info *mac = &hw->mac; 131 132 /* Set mta register count */ 133 mac->mta_reg_count = 128; 134 mac->rar_entry_count = IGC_RAR_ENTRIES; 135 136 /* reset */ 137 mac->ops.reset_hw = igc_reset_hw_base; 138 139 mac->ops.acquire_swfw_sync = igc_acquire_swfw_sync_i225; 140 mac->ops.release_swfw_sync = igc_release_swfw_sync_i225; 141 142 /* Allow a single clear of the SW semaphore on I225 */ 143 if (mac->type == igc_i225) 144 dev_spec->clear_semaphore_once = true; 145 146 /* physical interface link setup */ 147 mac->ops.setup_physical_interface = igc_setup_copper_link_base; 148 149 return 0; 150 } 151 152 /** 153 * igc_init_phy_params_base - Init PHY func ptrs. 154 * @hw: pointer to the HW structure 155 */ 156 static s32 igc_init_phy_params_base(struct igc_hw *hw) 157 { 158 struct igc_phy_info *phy = &hw->phy; 159 s32 ret_val = 0; 160 161 if (hw->phy.media_type != igc_media_type_copper) { 162 phy->type = igc_phy_none; 163 goto out; 164 } 165 166 phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT_2500; 167 phy->reset_delay_us = 100; 168 169 /* set lan id */ 170 hw->bus.func = (rd32(IGC_STATUS) & IGC_STATUS_FUNC_MASK) >> 171 IGC_STATUS_FUNC_SHIFT; 172 173 /* Make sure the PHY is in a good state. Several people have reported 174 * firmware leaving the PHY's page select register set to something 175 * other than the default of zero, which causes the PHY ID read to 176 * access something other than the intended register. 177 */ 178 ret_val = hw->phy.ops.reset(hw); 179 if (ret_val) { 180 hw_dbg("Error resetting the PHY.\n"); 181 goto out; 182 } 183 184 ret_val = igc_get_phy_id(hw); 185 if (ret_val) 186 return ret_val; 187 188 igc_check_for_copper_link(hw); 189 190 /* Verify phy id and set remaining function pointers */ 191 switch (phy->id) { 192 case I225_I_PHY_ID: 193 phy->type = igc_phy_i225; 194 break; 195 default: 196 ret_val = -IGC_ERR_PHY; 197 goto out; 198 } 199 200 out: 201 return ret_val; 202 } 203 204 static s32 igc_get_invariants_base(struct igc_hw *hw) 205 { 206 struct igc_mac_info *mac = &hw->mac; 207 s32 ret_val = 0; 208 209 switch (hw->device_id) { 210 case IGC_DEV_ID_I225_LM: 211 case IGC_DEV_ID_I225_V: 212 case IGC_DEV_ID_I225_I: 213 case IGC_DEV_ID_I220_V: 214 case IGC_DEV_ID_I225_K: 215 case IGC_DEV_ID_I225_BLANK_NVM: 216 mac->type = igc_i225; 217 break; 218 default: 219 return -IGC_ERR_MAC_INIT; 220 } 221 222 hw->phy.media_type = igc_media_type_copper; 223 224 /* mac initialization and operations */ 225 ret_val = igc_init_mac_params_base(hw); 226 if (ret_val) 227 goto out; 228 229 /* NVM initialization */ 230 ret_val = igc_init_nvm_params_base(hw); 231 switch (hw->mac.type) { 232 case igc_i225: 233 ret_val = igc_init_nvm_params_i225(hw); 234 break; 235 default: 236 break; 237 } 238 239 /* setup PHY parameters */ 240 ret_val = igc_init_phy_params_base(hw); 241 if (ret_val) 242 goto out; 243 244 out: 245 return ret_val; 246 } 247 248 /** 249 * igc_acquire_phy_base - Acquire rights to access PHY 250 * @hw: pointer to the HW structure 251 * 252 * Acquire access rights to the correct PHY. This is a 253 * function pointer entry point called by the api module. 254 */ 255 static s32 igc_acquire_phy_base(struct igc_hw *hw) 256 { 257 u16 mask = IGC_SWFW_PHY0_SM; 258 259 return hw->mac.ops.acquire_swfw_sync(hw, mask); 260 } 261 262 /** 263 * igc_release_phy_base - Release rights to access PHY 264 * @hw: pointer to the HW structure 265 * 266 * A wrapper to release access rights to the correct PHY. This is a 267 * function pointer entry point called by the api module. 268 */ 269 static void igc_release_phy_base(struct igc_hw *hw) 270 { 271 u16 mask = IGC_SWFW_PHY0_SM; 272 273 hw->mac.ops.release_swfw_sync(hw, mask); 274 } 275 276 /** 277 * igc_init_hw_base - Initialize hardware 278 * @hw: pointer to the HW structure 279 * 280 * This inits the hardware readying it for operation. 281 */ 282 static s32 igc_init_hw_base(struct igc_hw *hw) 283 { 284 struct igc_mac_info *mac = &hw->mac; 285 u16 i, rar_count = mac->rar_entry_count; 286 s32 ret_val = 0; 287 288 /* Setup the receive address */ 289 igc_init_rx_addrs(hw, rar_count); 290 291 /* Zero out the Multicast HASH table */ 292 hw_dbg("Zeroing the MTA\n"); 293 for (i = 0; i < mac->mta_reg_count; i++) 294 array_wr32(IGC_MTA, i, 0); 295 296 /* Zero out the Unicast HASH table */ 297 hw_dbg("Zeroing the UTA\n"); 298 for (i = 0; i < mac->uta_reg_count; i++) 299 array_wr32(IGC_UTA, i, 0); 300 301 /* Setup link and flow control */ 302 ret_val = igc_setup_link(hw); 303 304 /* Clear all of the statistics registers (clear on read). It is 305 * important that we do this after we have tried to establish link 306 * because the symbol error count will increment wildly if there 307 * is no link. 308 */ 309 igc_clear_hw_cntrs_base(hw); 310 311 return ret_val; 312 } 313 314 /** 315 * igc_power_down_phy_copper_base - Remove link during PHY power down 316 * @hw: pointer to the HW structure 317 * 318 * In the case of a PHY power down to save power, or to turn off link during a 319 * driver unload, or wake on lan is not enabled, remove the link. 320 */ 321 void igc_power_down_phy_copper_base(struct igc_hw *hw) 322 { 323 /* If the management interface is not enabled, then power down */ 324 if (!(igc_enable_mng_pass_thru(hw) || igc_check_reset_block(hw))) 325 igc_power_down_phy_copper(hw); 326 } 327 328 /** 329 * igc_rx_fifo_flush_base - Clean rx fifo after Rx enable 330 * @hw: pointer to the HW structure 331 * 332 * After Rx enable, if manageability is enabled then there is likely some 333 * bad data at the start of the fifo and possibly in the DMA fifo. This 334 * function clears the fifos and flushes any packets that came in as rx was 335 * being enabled. 336 */ 337 void igc_rx_fifo_flush_base(struct igc_hw *hw) 338 { 339 u32 rctl, rlpml, rxdctl[4], rfctl, temp_rctl, rx_enabled; 340 int i, ms_wait; 341 342 /* disable IPv6 options as per hardware errata */ 343 rfctl = rd32(IGC_RFCTL); 344 rfctl |= IGC_RFCTL_IPV6_EX_DIS; 345 wr32(IGC_RFCTL, rfctl); 346 347 if (!(rd32(IGC_MANC) & IGC_MANC_RCV_TCO_EN)) 348 return; 349 350 /* Disable all Rx queues */ 351 for (i = 0; i < 4; i++) { 352 rxdctl[i] = rd32(IGC_RXDCTL(i)); 353 wr32(IGC_RXDCTL(i), 354 rxdctl[i] & ~IGC_RXDCTL_QUEUE_ENABLE); 355 } 356 /* Poll all queues to verify they have shut down */ 357 for (ms_wait = 0; ms_wait < 10; ms_wait++) { 358 usleep_range(1000, 2000); 359 rx_enabled = 0; 360 for (i = 0; i < 4; i++) 361 rx_enabled |= rd32(IGC_RXDCTL(i)); 362 if (!(rx_enabled & IGC_RXDCTL_QUEUE_ENABLE)) 363 break; 364 } 365 366 if (ms_wait == 10) 367 pr_debug("Queue disable timed out after 10ms\n"); 368 369 /* Clear RLPML, RCTL.SBP, RFCTL.LEF, and set RCTL.LPE so that all 370 * incoming packets are rejected. Set enable and wait 2ms so that 371 * any packet that was coming in as RCTL.EN was set is flushed 372 */ 373 wr32(IGC_RFCTL, rfctl & ~IGC_RFCTL_LEF); 374 375 rlpml = rd32(IGC_RLPML); 376 wr32(IGC_RLPML, 0); 377 378 rctl = rd32(IGC_RCTL); 379 temp_rctl = rctl & ~(IGC_RCTL_EN | IGC_RCTL_SBP); 380 temp_rctl |= IGC_RCTL_LPE; 381 382 wr32(IGC_RCTL, temp_rctl); 383 wr32(IGC_RCTL, temp_rctl | IGC_RCTL_EN); 384 wrfl(); 385 usleep_range(2000, 3000); 386 387 /* Enable Rx queues that were previously enabled and restore our 388 * previous state 389 */ 390 for (i = 0; i < 4; i++) 391 wr32(IGC_RXDCTL(i), rxdctl[i]); 392 wr32(IGC_RCTL, rctl); 393 wrfl(); 394 395 wr32(IGC_RLPML, rlpml); 396 wr32(IGC_RFCTL, rfctl); 397 398 /* Flush receive errors generated by workaround */ 399 rd32(IGC_ROC); 400 rd32(IGC_RNBC); 401 rd32(IGC_MPC); 402 } 403 404 static struct igc_mac_operations igc_mac_ops_base = { 405 .init_hw = igc_init_hw_base, 406 .check_for_link = igc_check_for_copper_link, 407 .rar_set = igc_rar_set, 408 .read_mac_addr = igc_read_mac_addr, 409 .get_speed_and_duplex = igc_get_speed_and_duplex_copper, 410 }; 411 412 static const struct igc_phy_operations igc_phy_ops_base = { 413 .acquire = igc_acquire_phy_base, 414 .release = igc_release_phy_base, 415 .reset = igc_phy_hw_reset, 416 .read_reg = igc_read_phy_reg_gpy, 417 .write_reg = igc_write_phy_reg_gpy, 418 }; 419 420 const struct igc_info igc_base_info = { 421 .get_invariants = igc_get_invariants_base, 422 .mac_ops = &igc_mac_ops_base, 423 .phy_ops = &igc_phy_ops_base, 424 }; 425