1 // SPDX-License-Identifier: GPL-2.0 2 /* Copyright(c) 1999 - 2018 Intel Corporation. */ 3 4 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt 5 6 #include <linux/module.h> 7 #include <linux/types.h> 8 #include <linux/init.h> 9 #include <linux/pci.h> 10 #include <linux/vmalloc.h> 11 #include <linux/pagemap.h> 12 #include <linux/delay.h> 13 #include <linux/netdevice.h> 14 #include <linux/interrupt.h> 15 #include <linux/tcp.h> 16 #include <linux/ipv6.h> 17 #include <linux/slab.h> 18 #include <net/checksum.h> 19 #include <net/ip6_checksum.h> 20 #include <linux/ethtool.h> 21 #include <linux/if_vlan.h> 22 #include <linux/cpu.h> 23 #include <linux/smp.h> 24 #include <linux/pm_qos.h> 25 #include <linux/pm_runtime.h> 26 #include <linux/aer.h> 27 #include <linux/prefetch.h> 28 29 #include "e1000.h" 30 31 #define DRV_EXTRAVERSION "-k" 32 33 #define DRV_VERSION "3.2.6" DRV_EXTRAVERSION 34 char e1000e_driver_name[] = "e1000e"; 35 const char e1000e_driver_version[] = DRV_VERSION; 36 37 #define DEFAULT_MSG_ENABLE (NETIF_MSG_DRV|NETIF_MSG_PROBE|NETIF_MSG_LINK) 38 static int debug = -1; 39 module_param(debug, int, 0); 40 MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)"); 41 42 static const struct e1000_info *e1000_info_tbl[] = { 43 [board_82571] = &e1000_82571_info, 44 [board_82572] = &e1000_82572_info, 45 [board_82573] = &e1000_82573_info, 46 [board_82574] = &e1000_82574_info, 47 [board_82583] = &e1000_82583_info, 48 [board_80003es2lan] = &e1000_es2_info, 49 [board_ich8lan] = &e1000_ich8_info, 50 [board_ich9lan] = &e1000_ich9_info, 51 [board_ich10lan] = &e1000_ich10_info, 52 [board_pchlan] = &e1000_pch_info, 53 [board_pch2lan] = &e1000_pch2_info, 54 [board_pch_lpt] = &e1000_pch_lpt_info, 55 [board_pch_spt] = &e1000_pch_spt_info, 56 [board_pch_cnp] = &e1000_pch_cnp_info, 57 }; 58 59 struct e1000_reg_info { 60 u32 ofs; 61 char *name; 62 }; 63 64 static const struct e1000_reg_info e1000_reg_info_tbl[] = { 65 /* General Registers */ 66 {E1000_CTRL, "CTRL"}, 67 {E1000_STATUS, "STATUS"}, 68 {E1000_CTRL_EXT, "CTRL_EXT"}, 69 70 /* Interrupt Registers */ 71 {E1000_ICR, "ICR"}, 72 73 /* Rx Registers */ 74 {E1000_RCTL, "RCTL"}, 75 {E1000_RDLEN(0), "RDLEN"}, 76 {E1000_RDH(0), "RDH"}, 77 {E1000_RDT(0), "RDT"}, 78 {E1000_RDTR, "RDTR"}, 79 {E1000_RXDCTL(0), "RXDCTL"}, 80 {E1000_ERT, "ERT"}, 81 {E1000_RDBAL(0), "RDBAL"}, 82 {E1000_RDBAH(0), "RDBAH"}, 83 {E1000_RDFH, "RDFH"}, 84 {E1000_RDFT, "RDFT"}, 85 {E1000_RDFHS, "RDFHS"}, 86 {E1000_RDFTS, "RDFTS"}, 87 {E1000_RDFPC, "RDFPC"}, 88 89 /* Tx Registers */ 90 {E1000_TCTL, "TCTL"}, 91 {E1000_TDBAL(0), "TDBAL"}, 92 {E1000_TDBAH(0), "TDBAH"}, 93 {E1000_TDLEN(0), "TDLEN"}, 94 {E1000_TDH(0), "TDH"}, 95 {E1000_TDT(0), "TDT"}, 96 {E1000_TIDV, "TIDV"}, 97 {E1000_TXDCTL(0), "TXDCTL"}, 98 {E1000_TADV, "TADV"}, 99 {E1000_TARC(0), "TARC"}, 100 {E1000_TDFH, "TDFH"}, 101 {E1000_TDFT, "TDFT"}, 102 {E1000_TDFHS, "TDFHS"}, 103 {E1000_TDFTS, "TDFTS"}, 104 {E1000_TDFPC, "TDFPC"}, 105 106 /* List Terminator */ 107 {0, NULL} 108 }; 109 110 /** 111 * __ew32_prepare - prepare to write to MAC CSR register on certain parts 112 * @hw: pointer to the HW structure 113 * 114 * When updating the MAC CSR registers, the Manageability Engine (ME) could 115 * be accessing the registers at the same time. Normally, this is handled in 116 * h/w by an arbiter but on some parts there is a bug that acknowledges Host 117 * accesses later than it should which could result in the register to have 118 * an incorrect value. Workaround this by checking the FWSM register which 119 * has bit 24 set while ME is accessing MAC CSR registers, wait if it is set 120 * and try again a number of times. 121 **/ 122 s32 __ew32_prepare(struct e1000_hw *hw) 123 { 124 s32 i = E1000_ICH_FWSM_PCIM2PCI_COUNT; 125 126 while ((er32(FWSM) & E1000_ICH_FWSM_PCIM2PCI) && --i) 127 udelay(50); 128 129 return i; 130 } 131 132 void __ew32(struct e1000_hw *hw, unsigned long reg, u32 val) 133 { 134 if (hw->adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA) 135 __ew32_prepare(hw); 136 137 writel(val, hw->hw_addr + reg); 138 } 139 140 /** 141 * e1000_regdump - register printout routine 142 * @hw: pointer to the HW structure 143 * @reginfo: pointer to the register info table 144 **/ 145 static void e1000_regdump(struct e1000_hw *hw, struct e1000_reg_info *reginfo) 146 { 147 int n = 0; 148 char rname[16]; 149 u32 regs[8]; 150 151 switch (reginfo->ofs) { 152 case E1000_RXDCTL(0): 153 for (n = 0; n < 2; n++) 154 regs[n] = __er32(hw, E1000_RXDCTL(n)); 155 break; 156 case E1000_TXDCTL(0): 157 for (n = 0; n < 2; n++) 158 regs[n] = __er32(hw, E1000_TXDCTL(n)); 159 break; 160 case E1000_TARC(0): 161 for (n = 0; n < 2; n++) 162 regs[n] = __er32(hw, E1000_TARC(n)); 163 break; 164 default: 165 pr_info("%-15s %08x\n", 166 reginfo->name, __er32(hw, reginfo->ofs)); 167 return; 168 } 169 170 snprintf(rname, 16, "%s%s", reginfo->name, "[0-1]"); 171 pr_info("%-15s %08x %08x\n", rname, regs[0], regs[1]); 172 } 173 174 static void e1000e_dump_ps_pages(struct e1000_adapter *adapter, 175 struct e1000_buffer *bi) 176 { 177 int i; 178 struct e1000_ps_page *ps_page; 179 180 for (i = 0; i < adapter->rx_ps_pages; i++) { 181 ps_page = &bi->ps_pages[i]; 182 183 if (ps_page->page) { 184 pr_info("packet dump for ps_page %d:\n", i); 185 print_hex_dump(KERN_INFO, "", DUMP_PREFIX_ADDRESS, 186 16, 1, page_address(ps_page->page), 187 PAGE_SIZE, true); 188 } 189 } 190 } 191 192 /** 193 * e1000e_dump - Print registers, Tx-ring and Rx-ring 194 * @adapter: board private structure 195 **/ 196 static void e1000e_dump(struct e1000_adapter *adapter) 197 { 198 struct net_device *netdev = adapter->netdev; 199 struct e1000_hw *hw = &adapter->hw; 200 struct e1000_reg_info *reginfo; 201 struct e1000_ring *tx_ring = adapter->tx_ring; 202 struct e1000_tx_desc *tx_desc; 203 struct my_u0 { 204 __le64 a; 205 __le64 b; 206 } *u0; 207 struct e1000_buffer *buffer_info; 208 struct e1000_ring *rx_ring = adapter->rx_ring; 209 union e1000_rx_desc_packet_split *rx_desc_ps; 210 union e1000_rx_desc_extended *rx_desc; 211 struct my_u1 { 212 __le64 a; 213 __le64 b; 214 __le64 c; 215 __le64 d; 216 } *u1; 217 u32 staterr; 218 int i = 0; 219 220 if (!netif_msg_hw(adapter)) 221 return; 222 223 /* Print netdevice Info */ 224 if (netdev) { 225 dev_info(&adapter->pdev->dev, "Net device Info\n"); 226 pr_info("Device Name state trans_start\n"); 227 pr_info("%-15s %016lX %016lX\n", netdev->name, 228 netdev->state, dev_trans_start(netdev)); 229 } 230 231 /* Print Registers */ 232 dev_info(&adapter->pdev->dev, "Register Dump\n"); 233 pr_info(" Register Name Value\n"); 234 for (reginfo = (struct e1000_reg_info *)e1000_reg_info_tbl; 235 reginfo->name; reginfo++) { 236 e1000_regdump(hw, reginfo); 237 } 238 239 /* Print Tx Ring Summary */ 240 if (!netdev || !netif_running(netdev)) 241 return; 242 243 dev_info(&adapter->pdev->dev, "Tx Ring Summary\n"); 244 pr_info("Queue [NTU] [NTC] [bi(ntc)->dma ] leng ntw timestamp\n"); 245 buffer_info = &tx_ring->buffer_info[tx_ring->next_to_clean]; 246 pr_info(" %5d %5X %5X %016llX %04X %3X %016llX\n", 247 0, tx_ring->next_to_use, tx_ring->next_to_clean, 248 (unsigned long long)buffer_info->dma, 249 buffer_info->length, 250 buffer_info->next_to_watch, 251 (unsigned long long)buffer_info->time_stamp); 252 253 /* Print Tx Ring */ 254 if (!netif_msg_tx_done(adapter)) 255 goto rx_ring_summary; 256 257 dev_info(&adapter->pdev->dev, "Tx Ring Dump\n"); 258 259 /* Transmit Descriptor Formats - DEXT[29] is 0 (Legacy) or 1 (Extended) 260 * 261 * Legacy Transmit Descriptor 262 * +--------------------------------------------------------------+ 263 * 0 | Buffer Address [63:0] (Reserved on Write Back) | 264 * +--------------------------------------------------------------+ 265 * 8 | Special | CSS | Status | CMD | CSO | Length | 266 * +--------------------------------------------------------------+ 267 * 63 48 47 36 35 32 31 24 23 16 15 0 268 * 269 * Extended Context Descriptor (DTYP=0x0) for TSO or checksum offload 270 * 63 48 47 40 39 32 31 16 15 8 7 0 271 * +----------------------------------------------------------------+ 272 * 0 | TUCSE | TUCS0 | TUCSS | IPCSE | IPCS0 | IPCSS | 273 * +----------------------------------------------------------------+ 274 * 8 | MSS | HDRLEN | RSV | STA | TUCMD | DTYP | PAYLEN | 275 * +----------------------------------------------------------------+ 276 * 63 48 47 40 39 36 35 32 31 24 23 20 19 0 277 * 278 * Extended Data Descriptor (DTYP=0x1) 279 * +----------------------------------------------------------------+ 280 * 0 | Buffer Address [63:0] | 281 * +----------------------------------------------------------------+ 282 * 8 | VLAN tag | POPTS | Rsvd | Status | Command | DTYP | DTALEN | 283 * +----------------------------------------------------------------+ 284 * 63 48 47 40 39 36 35 32 31 24 23 20 19 0 285 */ 286 pr_info("Tl[desc] [address 63:0 ] [SpeCssSCmCsLen] [bi->dma ] leng ntw timestamp bi->skb <-- Legacy format\n"); 287 pr_info("Tc[desc] [Ce CoCsIpceCoS] [MssHlRSCm0Plen] [bi->dma ] leng ntw timestamp bi->skb <-- Ext Context format\n"); 288 pr_info("Td[desc] [address 63:0 ] [VlaPoRSCm1Dlen] [bi->dma ] leng ntw timestamp bi->skb <-- Ext Data format\n"); 289 for (i = 0; tx_ring->desc && (i < tx_ring->count); i++) { 290 const char *next_desc; 291 tx_desc = E1000_TX_DESC(*tx_ring, i); 292 buffer_info = &tx_ring->buffer_info[i]; 293 u0 = (struct my_u0 *)tx_desc; 294 if (i == tx_ring->next_to_use && i == tx_ring->next_to_clean) 295 next_desc = " NTC/U"; 296 else if (i == tx_ring->next_to_use) 297 next_desc = " NTU"; 298 else if (i == tx_ring->next_to_clean) 299 next_desc = " NTC"; 300 else 301 next_desc = ""; 302 pr_info("T%c[0x%03X] %016llX %016llX %016llX %04X %3X %016llX %p%s\n", 303 (!(le64_to_cpu(u0->b) & BIT(29)) ? 'l' : 304 ((le64_to_cpu(u0->b) & BIT(20)) ? 'd' : 'c')), 305 i, 306 (unsigned long long)le64_to_cpu(u0->a), 307 (unsigned long long)le64_to_cpu(u0->b), 308 (unsigned long long)buffer_info->dma, 309 buffer_info->length, buffer_info->next_to_watch, 310 (unsigned long long)buffer_info->time_stamp, 311 buffer_info->skb, next_desc); 312 313 if (netif_msg_pktdata(adapter) && buffer_info->skb) 314 print_hex_dump(KERN_INFO, "", DUMP_PREFIX_ADDRESS, 315 16, 1, buffer_info->skb->data, 316 buffer_info->skb->len, true); 317 } 318 319 /* Print Rx Ring Summary */ 320 rx_ring_summary: 321 dev_info(&adapter->pdev->dev, "Rx Ring Summary\n"); 322 pr_info("Queue [NTU] [NTC]\n"); 323 pr_info(" %5d %5X %5X\n", 324 0, rx_ring->next_to_use, rx_ring->next_to_clean); 325 326 /* Print Rx Ring */ 327 if (!netif_msg_rx_status(adapter)) 328 return; 329 330 dev_info(&adapter->pdev->dev, "Rx Ring Dump\n"); 331 switch (adapter->rx_ps_pages) { 332 case 1: 333 case 2: 334 case 3: 335 /* [Extended] Packet Split Receive Descriptor Format 336 * 337 * +-----------------------------------------------------+ 338 * 0 | Buffer Address 0 [63:0] | 339 * +-----------------------------------------------------+ 340 * 8 | Buffer Address 1 [63:0] | 341 * +-----------------------------------------------------+ 342 * 16 | Buffer Address 2 [63:0] | 343 * +-----------------------------------------------------+ 344 * 24 | Buffer Address 3 [63:0] | 345 * +-----------------------------------------------------+ 346 */ 347 pr_info("R [desc] [buffer 0 63:0 ] [buffer 1 63:0 ] [buffer 2 63:0 ] [buffer 3 63:0 ] [bi->dma ] [bi->skb] <-- Ext Pkt Split format\n"); 348 /* [Extended] Receive Descriptor (Write-Back) Format 349 * 350 * 63 48 47 32 31 13 12 8 7 4 3 0 351 * +------------------------------------------------------+ 352 * 0 | Packet | IP | Rsvd | MRQ | Rsvd | MRQ RSS | 353 * | Checksum | Ident | | Queue | | Type | 354 * +------------------------------------------------------+ 355 * 8 | VLAN Tag | Length | Extended Error | Extended Status | 356 * +------------------------------------------------------+ 357 * 63 48 47 32 31 20 19 0 358 */ 359 pr_info("RWB[desc] [ck ipid mrqhsh] [vl l0 ee es] [ l3 l2 l1 hs] [reserved ] ---------------- [bi->skb] <-- Ext Rx Write-Back format\n"); 360 for (i = 0; i < rx_ring->count; i++) { 361 const char *next_desc; 362 buffer_info = &rx_ring->buffer_info[i]; 363 rx_desc_ps = E1000_RX_DESC_PS(*rx_ring, i); 364 u1 = (struct my_u1 *)rx_desc_ps; 365 staterr = 366 le32_to_cpu(rx_desc_ps->wb.middle.status_error); 367 368 if (i == rx_ring->next_to_use) 369 next_desc = " NTU"; 370 else if (i == rx_ring->next_to_clean) 371 next_desc = " NTC"; 372 else 373 next_desc = ""; 374 375 if (staterr & E1000_RXD_STAT_DD) { 376 /* Descriptor Done */ 377 pr_info("%s[0x%03X] %016llX %016llX %016llX %016llX ---------------- %p%s\n", 378 "RWB", i, 379 (unsigned long long)le64_to_cpu(u1->a), 380 (unsigned long long)le64_to_cpu(u1->b), 381 (unsigned long long)le64_to_cpu(u1->c), 382 (unsigned long long)le64_to_cpu(u1->d), 383 buffer_info->skb, next_desc); 384 } else { 385 pr_info("%s[0x%03X] %016llX %016llX %016llX %016llX %016llX %p%s\n", 386 "R ", i, 387 (unsigned long long)le64_to_cpu(u1->a), 388 (unsigned long long)le64_to_cpu(u1->b), 389 (unsigned long long)le64_to_cpu(u1->c), 390 (unsigned long long)le64_to_cpu(u1->d), 391 (unsigned long long)buffer_info->dma, 392 buffer_info->skb, next_desc); 393 394 if (netif_msg_pktdata(adapter)) 395 e1000e_dump_ps_pages(adapter, 396 buffer_info); 397 } 398 } 399 break; 400 default: 401 case 0: 402 /* Extended Receive Descriptor (Read) Format 403 * 404 * +-----------------------------------------------------+ 405 * 0 | Buffer Address [63:0] | 406 * +-----------------------------------------------------+ 407 * 8 | Reserved | 408 * +-----------------------------------------------------+ 409 */ 410 pr_info("R [desc] [buf addr 63:0 ] [reserved 63:0 ] [bi->dma ] [bi->skb] <-- Ext (Read) format\n"); 411 /* Extended Receive Descriptor (Write-Back) Format 412 * 413 * 63 48 47 32 31 24 23 4 3 0 414 * +------------------------------------------------------+ 415 * | RSS Hash | | | | 416 * 0 +-------------------+ Rsvd | Reserved | MRQ RSS | 417 * | Packet | IP | | | Type | 418 * | Checksum | Ident | | | | 419 * +------------------------------------------------------+ 420 * 8 | VLAN Tag | Length | Extended Error | Extended Status | 421 * +------------------------------------------------------+ 422 * 63 48 47 32 31 20 19 0 423 */ 424 pr_info("RWB[desc] [cs ipid mrq] [vt ln xe xs] [bi->skb] <-- Ext (Write-Back) format\n"); 425 426 for (i = 0; i < rx_ring->count; i++) { 427 const char *next_desc; 428 429 buffer_info = &rx_ring->buffer_info[i]; 430 rx_desc = E1000_RX_DESC_EXT(*rx_ring, i); 431 u1 = (struct my_u1 *)rx_desc; 432 staterr = le32_to_cpu(rx_desc->wb.upper.status_error); 433 434 if (i == rx_ring->next_to_use) 435 next_desc = " NTU"; 436 else if (i == rx_ring->next_to_clean) 437 next_desc = " NTC"; 438 else 439 next_desc = ""; 440 441 if (staterr & E1000_RXD_STAT_DD) { 442 /* Descriptor Done */ 443 pr_info("%s[0x%03X] %016llX %016llX ---------------- %p%s\n", 444 "RWB", i, 445 (unsigned long long)le64_to_cpu(u1->a), 446 (unsigned long long)le64_to_cpu(u1->b), 447 buffer_info->skb, next_desc); 448 } else { 449 pr_info("%s[0x%03X] %016llX %016llX %016llX %p%s\n", 450 "R ", i, 451 (unsigned long long)le64_to_cpu(u1->a), 452 (unsigned long long)le64_to_cpu(u1->b), 453 (unsigned long long)buffer_info->dma, 454 buffer_info->skb, next_desc); 455 456 if (netif_msg_pktdata(adapter) && 457 buffer_info->skb) 458 print_hex_dump(KERN_INFO, "", 459 DUMP_PREFIX_ADDRESS, 16, 460 1, 461 buffer_info->skb->data, 462 adapter->rx_buffer_len, 463 true); 464 } 465 } 466 } 467 } 468 469 /** 470 * e1000_desc_unused - calculate if we have unused descriptors 471 **/ 472 static int e1000_desc_unused(struct e1000_ring *ring) 473 { 474 if (ring->next_to_clean > ring->next_to_use) 475 return ring->next_to_clean - ring->next_to_use - 1; 476 477 return ring->count + ring->next_to_clean - ring->next_to_use - 1; 478 } 479 480 /** 481 * e1000e_systim_to_hwtstamp - convert system time value to hw time stamp 482 * @adapter: board private structure 483 * @hwtstamps: time stamp structure to update 484 * @systim: unsigned 64bit system time value. 485 * 486 * Convert the system time value stored in the RX/TXSTMP registers into a 487 * hwtstamp which can be used by the upper level time stamping functions. 488 * 489 * The 'systim_lock' spinlock is used to protect the consistency of the 490 * system time value. This is needed because reading the 64 bit time 491 * value involves reading two 32 bit registers. The first read latches the 492 * value. 493 **/ 494 static void e1000e_systim_to_hwtstamp(struct e1000_adapter *adapter, 495 struct skb_shared_hwtstamps *hwtstamps, 496 u64 systim) 497 { 498 u64 ns; 499 unsigned long flags; 500 501 spin_lock_irqsave(&adapter->systim_lock, flags); 502 ns = timecounter_cyc2time(&adapter->tc, systim); 503 spin_unlock_irqrestore(&adapter->systim_lock, flags); 504 505 memset(hwtstamps, 0, sizeof(*hwtstamps)); 506 hwtstamps->hwtstamp = ns_to_ktime(ns); 507 } 508 509 /** 510 * e1000e_rx_hwtstamp - utility function which checks for Rx time stamp 511 * @adapter: board private structure 512 * @status: descriptor extended error and status field 513 * @skb: particular skb to include time stamp 514 * 515 * If the time stamp is valid, convert it into the timecounter ns value 516 * and store that result into the shhwtstamps structure which is passed 517 * up the network stack. 518 **/ 519 static void e1000e_rx_hwtstamp(struct e1000_adapter *adapter, u32 status, 520 struct sk_buff *skb) 521 { 522 struct e1000_hw *hw = &adapter->hw; 523 u64 rxstmp; 524 525 if (!(adapter->flags & FLAG_HAS_HW_TIMESTAMP) || 526 !(status & E1000_RXDEXT_STATERR_TST) || 527 !(er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_VALID)) 528 return; 529 530 /* The Rx time stamp registers contain the time stamp. No other 531 * received packet will be time stamped until the Rx time stamp 532 * registers are read. Because only one packet can be time stamped 533 * at a time, the register values must belong to this packet and 534 * therefore none of the other additional attributes need to be 535 * compared. 536 */ 537 rxstmp = (u64)er32(RXSTMPL); 538 rxstmp |= (u64)er32(RXSTMPH) << 32; 539 e1000e_systim_to_hwtstamp(adapter, skb_hwtstamps(skb), rxstmp); 540 541 adapter->flags2 &= ~FLAG2_CHECK_RX_HWTSTAMP; 542 } 543 544 /** 545 * e1000_receive_skb - helper function to handle Rx indications 546 * @adapter: board private structure 547 * @staterr: descriptor extended error and status field as written by hardware 548 * @vlan: descriptor vlan field as written by hardware (no le/be conversion) 549 * @skb: pointer to sk_buff to be indicated to stack 550 **/ 551 static void e1000_receive_skb(struct e1000_adapter *adapter, 552 struct net_device *netdev, struct sk_buff *skb, 553 u32 staterr, __le16 vlan) 554 { 555 u16 tag = le16_to_cpu(vlan); 556 557 e1000e_rx_hwtstamp(adapter, staterr, skb); 558 559 skb->protocol = eth_type_trans(skb, netdev); 560 561 if (staterr & E1000_RXD_STAT_VP) 562 __vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), tag); 563 564 napi_gro_receive(&adapter->napi, skb); 565 } 566 567 /** 568 * e1000_rx_checksum - Receive Checksum Offload 569 * @adapter: board private structure 570 * @status_err: receive descriptor status and error fields 571 * @csum: receive descriptor csum field 572 * @sk_buff: socket buffer with received data 573 **/ 574 static void e1000_rx_checksum(struct e1000_adapter *adapter, u32 status_err, 575 struct sk_buff *skb) 576 { 577 u16 status = (u16)status_err; 578 u8 errors = (u8)(status_err >> 24); 579 580 skb_checksum_none_assert(skb); 581 582 /* Rx checksum disabled */ 583 if (!(adapter->netdev->features & NETIF_F_RXCSUM)) 584 return; 585 586 /* Ignore Checksum bit is set */ 587 if (status & E1000_RXD_STAT_IXSM) 588 return; 589 590 /* TCP/UDP checksum error bit or IP checksum error bit is set */ 591 if (errors & (E1000_RXD_ERR_TCPE | E1000_RXD_ERR_IPE)) { 592 /* let the stack verify checksum errors */ 593 adapter->hw_csum_err++; 594 return; 595 } 596 597 /* TCP/UDP Checksum has not been calculated */ 598 if (!(status & (E1000_RXD_STAT_TCPCS | E1000_RXD_STAT_UDPCS))) 599 return; 600 601 /* It must be a TCP or UDP packet with a valid checksum */ 602 skb->ip_summed = CHECKSUM_UNNECESSARY; 603 adapter->hw_csum_good++; 604 } 605 606 static void e1000e_update_rdt_wa(struct e1000_ring *rx_ring, unsigned int i) 607 { 608 struct e1000_adapter *adapter = rx_ring->adapter; 609 struct e1000_hw *hw = &adapter->hw; 610 s32 ret_val = __ew32_prepare(hw); 611 612 writel(i, rx_ring->tail); 613 614 if (unlikely(!ret_val && (i != readl(rx_ring->tail)))) { 615 u32 rctl = er32(RCTL); 616 617 ew32(RCTL, rctl & ~E1000_RCTL_EN); 618 e_err("ME firmware caused invalid RDT - resetting\n"); 619 schedule_work(&adapter->reset_task); 620 } 621 } 622 623 static void e1000e_update_tdt_wa(struct e1000_ring *tx_ring, unsigned int i) 624 { 625 struct e1000_adapter *adapter = tx_ring->adapter; 626 struct e1000_hw *hw = &adapter->hw; 627 s32 ret_val = __ew32_prepare(hw); 628 629 writel(i, tx_ring->tail); 630 631 if (unlikely(!ret_val && (i != readl(tx_ring->tail)))) { 632 u32 tctl = er32(TCTL); 633 634 ew32(TCTL, tctl & ~E1000_TCTL_EN); 635 e_err("ME firmware caused invalid TDT - resetting\n"); 636 schedule_work(&adapter->reset_task); 637 } 638 } 639 640 /** 641 * e1000_alloc_rx_buffers - Replace used receive buffers 642 * @rx_ring: Rx descriptor ring 643 **/ 644 static void e1000_alloc_rx_buffers(struct e1000_ring *rx_ring, 645 int cleaned_count, gfp_t gfp) 646 { 647 struct e1000_adapter *adapter = rx_ring->adapter; 648 struct net_device *netdev = adapter->netdev; 649 struct pci_dev *pdev = adapter->pdev; 650 union e1000_rx_desc_extended *rx_desc; 651 struct e1000_buffer *buffer_info; 652 struct sk_buff *skb; 653 unsigned int i; 654 unsigned int bufsz = adapter->rx_buffer_len; 655 656 i = rx_ring->next_to_use; 657 buffer_info = &rx_ring->buffer_info[i]; 658 659 while (cleaned_count--) { 660 skb = buffer_info->skb; 661 if (skb) { 662 skb_trim(skb, 0); 663 goto map_skb; 664 } 665 666 skb = __netdev_alloc_skb_ip_align(netdev, bufsz, gfp); 667 if (!skb) { 668 /* Better luck next round */ 669 adapter->alloc_rx_buff_failed++; 670 break; 671 } 672 673 buffer_info->skb = skb; 674 map_skb: 675 buffer_info->dma = dma_map_single(&pdev->dev, skb->data, 676 adapter->rx_buffer_len, 677 DMA_FROM_DEVICE); 678 if (dma_mapping_error(&pdev->dev, buffer_info->dma)) { 679 dev_err(&pdev->dev, "Rx DMA map failed\n"); 680 adapter->rx_dma_failed++; 681 break; 682 } 683 684 rx_desc = E1000_RX_DESC_EXT(*rx_ring, i); 685 rx_desc->read.buffer_addr = cpu_to_le64(buffer_info->dma); 686 687 if (unlikely(!(i & (E1000_RX_BUFFER_WRITE - 1)))) { 688 /* Force memory writes to complete before letting h/w 689 * know there are new descriptors to fetch. (Only 690 * applicable for weak-ordered memory model archs, 691 * such as IA-64). 692 */ 693 wmb(); 694 if (adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA) 695 e1000e_update_rdt_wa(rx_ring, i); 696 else 697 writel(i, rx_ring->tail); 698 } 699 i++; 700 if (i == rx_ring->count) 701 i = 0; 702 buffer_info = &rx_ring->buffer_info[i]; 703 } 704 705 rx_ring->next_to_use = i; 706 } 707 708 /** 709 * e1000_alloc_rx_buffers_ps - Replace used receive buffers; packet split 710 * @rx_ring: Rx descriptor ring 711 **/ 712 static void e1000_alloc_rx_buffers_ps(struct e1000_ring *rx_ring, 713 int cleaned_count, gfp_t gfp) 714 { 715 struct e1000_adapter *adapter = rx_ring->adapter; 716 struct net_device *netdev = adapter->netdev; 717 struct pci_dev *pdev = adapter->pdev; 718 union e1000_rx_desc_packet_split *rx_desc; 719 struct e1000_buffer *buffer_info; 720 struct e1000_ps_page *ps_page; 721 struct sk_buff *skb; 722 unsigned int i, j; 723 724 i = rx_ring->next_to_use; 725 buffer_info = &rx_ring->buffer_info[i]; 726 727 while (cleaned_count--) { 728 rx_desc = E1000_RX_DESC_PS(*rx_ring, i); 729 730 for (j = 0; j < PS_PAGE_BUFFERS; j++) { 731 ps_page = &buffer_info->ps_pages[j]; 732 if (j >= adapter->rx_ps_pages) { 733 /* all unused desc entries get hw null ptr */ 734 rx_desc->read.buffer_addr[j + 1] = 735 ~cpu_to_le64(0); 736 continue; 737 } 738 if (!ps_page->page) { 739 ps_page->page = alloc_page(gfp); 740 if (!ps_page->page) { 741 adapter->alloc_rx_buff_failed++; 742 goto no_buffers; 743 } 744 ps_page->dma = dma_map_page(&pdev->dev, 745 ps_page->page, 746 0, PAGE_SIZE, 747 DMA_FROM_DEVICE); 748 if (dma_mapping_error(&pdev->dev, 749 ps_page->dma)) { 750 dev_err(&adapter->pdev->dev, 751 "Rx DMA page map failed\n"); 752 adapter->rx_dma_failed++; 753 goto no_buffers; 754 } 755 } 756 /* Refresh the desc even if buffer_addrs 757 * didn't change because each write-back 758 * erases this info. 759 */ 760 rx_desc->read.buffer_addr[j + 1] = 761 cpu_to_le64(ps_page->dma); 762 } 763 764 skb = __netdev_alloc_skb_ip_align(netdev, adapter->rx_ps_bsize0, 765 gfp); 766 767 if (!skb) { 768 adapter->alloc_rx_buff_failed++; 769 break; 770 } 771 772 buffer_info->skb = skb; 773 buffer_info->dma = dma_map_single(&pdev->dev, skb->data, 774 adapter->rx_ps_bsize0, 775 DMA_FROM_DEVICE); 776 if (dma_mapping_error(&pdev->dev, buffer_info->dma)) { 777 dev_err(&pdev->dev, "Rx DMA map failed\n"); 778 adapter->rx_dma_failed++; 779 /* cleanup skb */ 780 dev_kfree_skb_any(skb); 781 buffer_info->skb = NULL; 782 break; 783 } 784 785 rx_desc->read.buffer_addr[0] = cpu_to_le64(buffer_info->dma); 786 787 if (unlikely(!(i & (E1000_RX_BUFFER_WRITE - 1)))) { 788 /* Force memory writes to complete before letting h/w 789 * know there are new descriptors to fetch. (Only 790 * applicable for weak-ordered memory model archs, 791 * such as IA-64). 792 */ 793 wmb(); 794 if (adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA) 795 e1000e_update_rdt_wa(rx_ring, i << 1); 796 else 797 writel(i << 1, rx_ring->tail); 798 } 799 800 i++; 801 if (i == rx_ring->count) 802 i = 0; 803 buffer_info = &rx_ring->buffer_info[i]; 804 } 805 806 no_buffers: 807 rx_ring->next_to_use = i; 808 } 809 810 /** 811 * e1000_alloc_jumbo_rx_buffers - Replace used jumbo receive buffers 812 * @rx_ring: Rx descriptor ring 813 * @cleaned_count: number of buffers to allocate this pass 814 **/ 815 816 static void e1000_alloc_jumbo_rx_buffers(struct e1000_ring *rx_ring, 817 int cleaned_count, gfp_t gfp) 818 { 819 struct e1000_adapter *adapter = rx_ring->adapter; 820 struct net_device *netdev = adapter->netdev; 821 struct pci_dev *pdev = adapter->pdev; 822 union e1000_rx_desc_extended *rx_desc; 823 struct e1000_buffer *buffer_info; 824 struct sk_buff *skb; 825 unsigned int i; 826 unsigned int bufsz = 256 - 16; /* for skb_reserve */ 827 828 i = rx_ring->next_to_use; 829 buffer_info = &rx_ring->buffer_info[i]; 830 831 while (cleaned_count--) { 832 skb = buffer_info->skb; 833 if (skb) { 834 skb_trim(skb, 0); 835 goto check_page; 836 } 837 838 skb = __netdev_alloc_skb_ip_align(netdev, bufsz, gfp); 839 if (unlikely(!skb)) { 840 /* Better luck next round */ 841 adapter->alloc_rx_buff_failed++; 842 break; 843 } 844 845 buffer_info->skb = skb; 846 check_page: 847 /* allocate a new page if necessary */ 848 if (!buffer_info->page) { 849 buffer_info->page = alloc_page(gfp); 850 if (unlikely(!buffer_info->page)) { 851 adapter->alloc_rx_buff_failed++; 852 break; 853 } 854 } 855 856 if (!buffer_info->dma) { 857 buffer_info->dma = dma_map_page(&pdev->dev, 858 buffer_info->page, 0, 859 PAGE_SIZE, 860 DMA_FROM_DEVICE); 861 if (dma_mapping_error(&pdev->dev, buffer_info->dma)) { 862 adapter->alloc_rx_buff_failed++; 863 break; 864 } 865 } 866 867 rx_desc = E1000_RX_DESC_EXT(*rx_ring, i); 868 rx_desc->read.buffer_addr = cpu_to_le64(buffer_info->dma); 869 870 if (unlikely(++i == rx_ring->count)) 871 i = 0; 872 buffer_info = &rx_ring->buffer_info[i]; 873 } 874 875 if (likely(rx_ring->next_to_use != i)) { 876 rx_ring->next_to_use = i; 877 if (unlikely(i-- == 0)) 878 i = (rx_ring->count - 1); 879 880 /* Force memory writes to complete before letting h/w 881 * know there are new descriptors to fetch. (Only 882 * applicable for weak-ordered memory model archs, 883 * such as IA-64). 884 */ 885 wmb(); 886 if (adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA) 887 e1000e_update_rdt_wa(rx_ring, i); 888 else 889 writel(i, rx_ring->tail); 890 } 891 } 892 893 static inline void e1000_rx_hash(struct net_device *netdev, __le32 rss, 894 struct sk_buff *skb) 895 { 896 if (netdev->features & NETIF_F_RXHASH) 897 skb_set_hash(skb, le32_to_cpu(rss), PKT_HASH_TYPE_L3); 898 } 899 900 /** 901 * e1000_clean_rx_irq - Send received data up the network stack 902 * @rx_ring: Rx descriptor ring 903 * 904 * the return value indicates whether actual cleaning was done, there 905 * is no guarantee that everything was cleaned 906 **/ 907 static bool e1000_clean_rx_irq(struct e1000_ring *rx_ring, int *work_done, 908 int work_to_do) 909 { 910 struct e1000_adapter *adapter = rx_ring->adapter; 911 struct net_device *netdev = adapter->netdev; 912 struct pci_dev *pdev = adapter->pdev; 913 struct e1000_hw *hw = &adapter->hw; 914 union e1000_rx_desc_extended *rx_desc, *next_rxd; 915 struct e1000_buffer *buffer_info, *next_buffer; 916 u32 length, staterr; 917 unsigned int i; 918 int cleaned_count = 0; 919 bool cleaned = false; 920 unsigned int total_rx_bytes = 0, total_rx_packets = 0; 921 922 i = rx_ring->next_to_clean; 923 rx_desc = E1000_RX_DESC_EXT(*rx_ring, i); 924 staterr = le32_to_cpu(rx_desc->wb.upper.status_error); 925 buffer_info = &rx_ring->buffer_info[i]; 926 927 while (staterr & E1000_RXD_STAT_DD) { 928 struct sk_buff *skb; 929 930 if (*work_done >= work_to_do) 931 break; 932 (*work_done)++; 933 dma_rmb(); /* read descriptor and rx_buffer_info after status DD */ 934 935 skb = buffer_info->skb; 936 buffer_info->skb = NULL; 937 938 prefetch(skb->data - NET_IP_ALIGN); 939 940 i++; 941 if (i == rx_ring->count) 942 i = 0; 943 next_rxd = E1000_RX_DESC_EXT(*rx_ring, i); 944 prefetch(next_rxd); 945 946 next_buffer = &rx_ring->buffer_info[i]; 947 948 cleaned = true; 949 cleaned_count++; 950 dma_unmap_single(&pdev->dev, buffer_info->dma, 951 adapter->rx_buffer_len, DMA_FROM_DEVICE); 952 buffer_info->dma = 0; 953 954 length = le16_to_cpu(rx_desc->wb.upper.length); 955 956 /* !EOP means multiple descriptors were used to store a single 957 * packet, if that's the case we need to toss it. In fact, we 958 * need to toss every packet with the EOP bit clear and the 959 * next frame that _does_ have the EOP bit set, as it is by 960 * definition only a frame fragment 961 */ 962 if (unlikely(!(staterr & E1000_RXD_STAT_EOP))) 963 adapter->flags2 |= FLAG2_IS_DISCARDING; 964 965 if (adapter->flags2 & FLAG2_IS_DISCARDING) { 966 /* All receives must fit into a single buffer */ 967 e_dbg("Receive packet consumed multiple buffers\n"); 968 /* recycle */ 969 buffer_info->skb = skb; 970 if (staterr & E1000_RXD_STAT_EOP) 971 adapter->flags2 &= ~FLAG2_IS_DISCARDING; 972 goto next_desc; 973 } 974 975 if (unlikely((staterr & E1000_RXDEXT_ERR_FRAME_ERR_MASK) && 976 !(netdev->features & NETIF_F_RXALL))) { 977 /* recycle */ 978 buffer_info->skb = skb; 979 goto next_desc; 980 } 981 982 /* adjust length to remove Ethernet CRC */ 983 if (!(adapter->flags2 & FLAG2_CRC_STRIPPING)) { 984 /* If configured to store CRC, don't subtract FCS, 985 * but keep the FCS bytes out of the total_rx_bytes 986 * counter 987 */ 988 if (netdev->features & NETIF_F_RXFCS) 989 total_rx_bytes -= 4; 990 else 991 length -= 4; 992 } 993 994 total_rx_bytes += length; 995 total_rx_packets++; 996 997 /* code added for copybreak, this should improve 998 * performance for small packets with large amounts 999 * of reassembly being done in the stack 1000 */ 1001 if (length < copybreak) { 1002 struct sk_buff *new_skb = 1003 napi_alloc_skb(&adapter->napi, length); 1004 if (new_skb) { 1005 skb_copy_to_linear_data_offset(new_skb, 1006 -NET_IP_ALIGN, 1007 (skb->data - 1008 NET_IP_ALIGN), 1009 (length + 1010 NET_IP_ALIGN)); 1011 /* save the skb in buffer_info as good */ 1012 buffer_info->skb = skb; 1013 skb = new_skb; 1014 } 1015 /* else just continue with the old one */ 1016 } 1017 /* end copybreak code */ 1018 skb_put(skb, length); 1019 1020 /* Receive Checksum Offload */ 1021 e1000_rx_checksum(adapter, staterr, skb); 1022 1023 e1000_rx_hash(netdev, rx_desc->wb.lower.hi_dword.rss, skb); 1024 1025 e1000_receive_skb(adapter, netdev, skb, staterr, 1026 rx_desc->wb.upper.vlan); 1027 1028 next_desc: 1029 rx_desc->wb.upper.status_error &= cpu_to_le32(~0xFF); 1030 1031 /* return some buffers to hardware, one at a time is too slow */ 1032 if (cleaned_count >= E1000_RX_BUFFER_WRITE) { 1033 adapter->alloc_rx_buf(rx_ring, cleaned_count, 1034 GFP_ATOMIC); 1035 cleaned_count = 0; 1036 } 1037 1038 /* use prefetched values */ 1039 rx_desc = next_rxd; 1040 buffer_info = next_buffer; 1041 1042 staterr = le32_to_cpu(rx_desc->wb.upper.status_error); 1043 } 1044 rx_ring->next_to_clean = i; 1045 1046 cleaned_count = e1000_desc_unused(rx_ring); 1047 if (cleaned_count) 1048 adapter->alloc_rx_buf(rx_ring, cleaned_count, GFP_ATOMIC); 1049 1050 adapter->total_rx_bytes += total_rx_bytes; 1051 adapter->total_rx_packets += total_rx_packets; 1052 return cleaned; 1053 } 1054 1055 static void e1000_put_txbuf(struct e1000_ring *tx_ring, 1056 struct e1000_buffer *buffer_info, 1057 bool drop) 1058 { 1059 struct e1000_adapter *adapter = tx_ring->adapter; 1060 1061 if (buffer_info->dma) { 1062 if (buffer_info->mapped_as_page) 1063 dma_unmap_page(&adapter->pdev->dev, buffer_info->dma, 1064 buffer_info->length, DMA_TO_DEVICE); 1065 else 1066 dma_unmap_single(&adapter->pdev->dev, buffer_info->dma, 1067 buffer_info->length, DMA_TO_DEVICE); 1068 buffer_info->dma = 0; 1069 } 1070 if (buffer_info->skb) { 1071 if (drop) 1072 dev_kfree_skb_any(buffer_info->skb); 1073 else 1074 dev_consume_skb_any(buffer_info->skb); 1075 buffer_info->skb = NULL; 1076 } 1077 buffer_info->time_stamp = 0; 1078 } 1079 1080 static void e1000_print_hw_hang(struct work_struct *work) 1081 { 1082 struct e1000_adapter *adapter = container_of(work, 1083 struct e1000_adapter, 1084 print_hang_task); 1085 struct net_device *netdev = adapter->netdev; 1086 struct e1000_ring *tx_ring = adapter->tx_ring; 1087 unsigned int i = tx_ring->next_to_clean; 1088 unsigned int eop = tx_ring->buffer_info[i].next_to_watch; 1089 struct e1000_tx_desc *eop_desc = E1000_TX_DESC(*tx_ring, eop); 1090 struct e1000_hw *hw = &adapter->hw; 1091 u16 phy_status, phy_1000t_status, phy_ext_status; 1092 u16 pci_status; 1093 1094 if (test_bit(__E1000_DOWN, &adapter->state)) 1095 return; 1096 1097 if (!adapter->tx_hang_recheck && (adapter->flags2 & FLAG2_DMA_BURST)) { 1098 /* May be block on write-back, flush and detect again 1099 * flush pending descriptor writebacks to memory 1100 */ 1101 ew32(TIDV, adapter->tx_int_delay | E1000_TIDV_FPD); 1102 /* execute the writes immediately */ 1103 e1e_flush(); 1104 /* Due to rare timing issues, write to TIDV again to ensure 1105 * the write is successful 1106 */ 1107 ew32(TIDV, adapter->tx_int_delay | E1000_TIDV_FPD); 1108 /* execute the writes immediately */ 1109 e1e_flush(); 1110 adapter->tx_hang_recheck = true; 1111 return; 1112 } 1113 adapter->tx_hang_recheck = false; 1114 1115 if (er32(TDH(0)) == er32(TDT(0))) { 1116 e_dbg("false hang detected, ignoring\n"); 1117 return; 1118 } 1119 1120 /* Real hang detected */ 1121 netif_stop_queue(netdev); 1122 1123 e1e_rphy(hw, MII_BMSR, &phy_status); 1124 e1e_rphy(hw, MII_STAT1000, &phy_1000t_status); 1125 e1e_rphy(hw, MII_ESTATUS, &phy_ext_status); 1126 1127 pci_read_config_word(adapter->pdev, PCI_STATUS, &pci_status); 1128 1129 /* detected Hardware unit hang */ 1130 e_err("Detected Hardware Unit Hang:\n" 1131 " TDH <%x>\n" 1132 " TDT <%x>\n" 1133 " next_to_use <%x>\n" 1134 " next_to_clean <%x>\n" 1135 "buffer_info[next_to_clean]:\n" 1136 " time_stamp <%lx>\n" 1137 " next_to_watch <%x>\n" 1138 " jiffies <%lx>\n" 1139 " next_to_watch.status <%x>\n" 1140 "MAC Status <%x>\n" 1141 "PHY Status <%x>\n" 1142 "PHY 1000BASE-T Status <%x>\n" 1143 "PHY Extended Status <%x>\n" 1144 "PCI Status <%x>\n", 1145 readl(tx_ring->head), readl(tx_ring->tail), tx_ring->next_to_use, 1146 tx_ring->next_to_clean, tx_ring->buffer_info[eop].time_stamp, 1147 eop, jiffies, eop_desc->upper.fields.status, er32(STATUS), 1148 phy_status, phy_1000t_status, phy_ext_status, pci_status); 1149 1150 e1000e_dump(adapter); 1151 1152 /* Suggest workaround for known h/w issue */ 1153 if ((hw->mac.type == e1000_pchlan) && (er32(CTRL) & E1000_CTRL_TFCE)) 1154 e_err("Try turning off Tx pause (flow control) via ethtool\n"); 1155 } 1156 1157 /** 1158 * e1000e_tx_hwtstamp_work - check for Tx time stamp 1159 * @work: pointer to work struct 1160 * 1161 * This work function polls the TSYNCTXCTL valid bit to determine when a 1162 * timestamp has been taken for the current stored skb. The timestamp must 1163 * be for this skb because only one such packet is allowed in the queue. 1164 */ 1165 static void e1000e_tx_hwtstamp_work(struct work_struct *work) 1166 { 1167 struct e1000_adapter *adapter = container_of(work, struct e1000_adapter, 1168 tx_hwtstamp_work); 1169 struct e1000_hw *hw = &adapter->hw; 1170 1171 if (er32(TSYNCTXCTL) & E1000_TSYNCTXCTL_VALID) { 1172 struct sk_buff *skb = adapter->tx_hwtstamp_skb; 1173 struct skb_shared_hwtstamps shhwtstamps; 1174 u64 txstmp; 1175 1176 txstmp = er32(TXSTMPL); 1177 txstmp |= (u64)er32(TXSTMPH) << 32; 1178 1179 e1000e_systim_to_hwtstamp(adapter, &shhwtstamps, txstmp); 1180 1181 /* Clear the global tx_hwtstamp_skb pointer and force writes 1182 * prior to notifying the stack of a Tx timestamp. 1183 */ 1184 adapter->tx_hwtstamp_skb = NULL; 1185 wmb(); /* force write prior to skb_tstamp_tx */ 1186 1187 skb_tstamp_tx(skb, &shhwtstamps); 1188 dev_consume_skb_any(skb); 1189 } else if (time_after(jiffies, adapter->tx_hwtstamp_start 1190 + adapter->tx_timeout_factor * HZ)) { 1191 dev_kfree_skb_any(adapter->tx_hwtstamp_skb); 1192 adapter->tx_hwtstamp_skb = NULL; 1193 adapter->tx_hwtstamp_timeouts++; 1194 e_warn("clearing Tx timestamp hang\n"); 1195 } else { 1196 /* reschedule to check later */ 1197 schedule_work(&adapter->tx_hwtstamp_work); 1198 } 1199 } 1200 1201 /** 1202 * e1000_clean_tx_irq - Reclaim resources after transmit completes 1203 * @tx_ring: Tx descriptor ring 1204 * 1205 * the return value indicates whether actual cleaning was done, there 1206 * is no guarantee that everything was cleaned 1207 **/ 1208 static bool e1000_clean_tx_irq(struct e1000_ring *tx_ring) 1209 { 1210 struct e1000_adapter *adapter = tx_ring->adapter; 1211 struct net_device *netdev = adapter->netdev; 1212 struct e1000_hw *hw = &adapter->hw; 1213 struct e1000_tx_desc *tx_desc, *eop_desc; 1214 struct e1000_buffer *buffer_info; 1215 unsigned int i, eop; 1216 unsigned int count = 0; 1217 unsigned int total_tx_bytes = 0, total_tx_packets = 0; 1218 unsigned int bytes_compl = 0, pkts_compl = 0; 1219 1220 i = tx_ring->next_to_clean; 1221 eop = tx_ring->buffer_info[i].next_to_watch; 1222 eop_desc = E1000_TX_DESC(*tx_ring, eop); 1223 1224 while ((eop_desc->upper.data & cpu_to_le32(E1000_TXD_STAT_DD)) && 1225 (count < tx_ring->count)) { 1226 bool cleaned = false; 1227 1228 dma_rmb(); /* read buffer_info after eop_desc */ 1229 for (; !cleaned; count++) { 1230 tx_desc = E1000_TX_DESC(*tx_ring, i); 1231 buffer_info = &tx_ring->buffer_info[i]; 1232 cleaned = (i == eop); 1233 1234 if (cleaned) { 1235 total_tx_packets += buffer_info->segs; 1236 total_tx_bytes += buffer_info->bytecount; 1237 if (buffer_info->skb) { 1238 bytes_compl += buffer_info->skb->len; 1239 pkts_compl++; 1240 } 1241 } 1242 1243 e1000_put_txbuf(tx_ring, buffer_info, false); 1244 tx_desc->upper.data = 0; 1245 1246 i++; 1247 if (i == tx_ring->count) 1248 i = 0; 1249 } 1250 1251 if (i == tx_ring->next_to_use) 1252 break; 1253 eop = tx_ring->buffer_info[i].next_to_watch; 1254 eop_desc = E1000_TX_DESC(*tx_ring, eop); 1255 } 1256 1257 tx_ring->next_to_clean = i; 1258 1259 netdev_completed_queue(netdev, pkts_compl, bytes_compl); 1260 1261 #define TX_WAKE_THRESHOLD 32 1262 if (count && netif_carrier_ok(netdev) && 1263 e1000_desc_unused(tx_ring) >= TX_WAKE_THRESHOLD) { 1264 /* Make sure that anybody stopping the queue after this 1265 * sees the new next_to_clean. 1266 */ 1267 smp_mb(); 1268 1269 if (netif_queue_stopped(netdev) && 1270 !(test_bit(__E1000_DOWN, &adapter->state))) { 1271 netif_wake_queue(netdev); 1272 ++adapter->restart_queue; 1273 } 1274 } 1275 1276 if (adapter->detect_tx_hung) { 1277 /* Detect a transmit hang in hardware, this serializes the 1278 * check with the clearing of time_stamp and movement of i 1279 */ 1280 adapter->detect_tx_hung = false; 1281 if (tx_ring->buffer_info[i].time_stamp && 1282 time_after(jiffies, tx_ring->buffer_info[i].time_stamp 1283 + (adapter->tx_timeout_factor * HZ)) && 1284 !(er32(STATUS) & E1000_STATUS_TXOFF)) 1285 schedule_work(&adapter->print_hang_task); 1286 else 1287 adapter->tx_hang_recheck = false; 1288 } 1289 adapter->total_tx_bytes += total_tx_bytes; 1290 adapter->total_tx_packets += total_tx_packets; 1291 return count < tx_ring->count; 1292 } 1293 1294 /** 1295 * e1000_clean_rx_irq_ps - Send received data up the network stack; packet split 1296 * @rx_ring: Rx descriptor ring 1297 * 1298 * the return value indicates whether actual cleaning was done, there 1299 * is no guarantee that everything was cleaned 1300 **/ 1301 static bool e1000_clean_rx_irq_ps(struct e1000_ring *rx_ring, int *work_done, 1302 int work_to_do) 1303 { 1304 struct e1000_adapter *adapter = rx_ring->adapter; 1305 struct e1000_hw *hw = &adapter->hw; 1306 union e1000_rx_desc_packet_split *rx_desc, *next_rxd; 1307 struct net_device *netdev = adapter->netdev; 1308 struct pci_dev *pdev = adapter->pdev; 1309 struct e1000_buffer *buffer_info, *next_buffer; 1310 struct e1000_ps_page *ps_page; 1311 struct sk_buff *skb; 1312 unsigned int i, j; 1313 u32 length, staterr; 1314 int cleaned_count = 0; 1315 bool cleaned = false; 1316 unsigned int total_rx_bytes = 0, total_rx_packets = 0; 1317 1318 i = rx_ring->next_to_clean; 1319 rx_desc = E1000_RX_DESC_PS(*rx_ring, i); 1320 staterr = le32_to_cpu(rx_desc->wb.middle.status_error); 1321 buffer_info = &rx_ring->buffer_info[i]; 1322 1323 while (staterr & E1000_RXD_STAT_DD) { 1324 if (*work_done >= work_to_do) 1325 break; 1326 (*work_done)++; 1327 skb = buffer_info->skb; 1328 dma_rmb(); /* read descriptor and rx_buffer_info after status DD */ 1329 1330 /* in the packet split case this is header only */ 1331 prefetch(skb->data - NET_IP_ALIGN); 1332 1333 i++; 1334 if (i == rx_ring->count) 1335 i = 0; 1336 next_rxd = E1000_RX_DESC_PS(*rx_ring, i); 1337 prefetch(next_rxd); 1338 1339 next_buffer = &rx_ring->buffer_info[i]; 1340 1341 cleaned = true; 1342 cleaned_count++; 1343 dma_unmap_single(&pdev->dev, buffer_info->dma, 1344 adapter->rx_ps_bsize0, DMA_FROM_DEVICE); 1345 buffer_info->dma = 0; 1346 1347 /* see !EOP comment in other Rx routine */ 1348 if (!(staterr & E1000_RXD_STAT_EOP)) 1349 adapter->flags2 |= FLAG2_IS_DISCARDING; 1350 1351 if (adapter->flags2 & FLAG2_IS_DISCARDING) { 1352 e_dbg("Packet Split buffers didn't pick up the full packet\n"); 1353 dev_kfree_skb_irq(skb); 1354 if (staterr & E1000_RXD_STAT_EOP) 1355 adapter->flags2 &= ~FLAG2_IS_DISCARDING; 1356 goto next_desc; 1357 } 1358 1359 if (unlikely((staterr & E1000_RXDEXT_ERR_FRAME_ERR_MASK) && 1360 !(netdev->features & NETIF_F_RXALL))) { 1361 dev_kfree_skb_irq(skb); 1362 goto next_desc; 1363 } 1364 1365 length = le16_to_cpu(rx_desc->wb.middle.length0); 1366 1367 if (!length) { 1368 e_dbg("Last part of the packet spanning multiple descriptors\n"); 1369 dev_kfree_skb_irq(skb); 1370 goto next_desc; 1371 } 1372 1373 /* Good Receive */ 1374 skb_put(skb, length); 1375 1376 { 1377 /* this looks ugly, but it seems compiler issues make 1378 * it more efficient than reusing j 1379 */ 1380 int l1 = le16_to_cpu(rx_desc->wb.upper.length[0]); 1381 1382 /* page alloc/put takes too long and effects small 1383 * packet throughput, so unsplit small packets and 1384 * save the alloc/put only valid in softirq (napi) 1385 * context to call kmap_* 1386 */ 1387 if (l1 && (l1 <= copybreak) && 1388 ((length + l1) <= adapter->rx_ps_bsize0)) { 1389 u8 *vaddr; 1390 1391 ps_page = &buffer_info->ps_pages[0]; 1392 1393 /* there is no documentation about how to call 1394 * kmap_atomic, so we can't hold the mapping 1395 * very long 1396 */ 1397 dma_sync_single_for_cpu(&pdev->dev, 1398 ps_page->dma, 1399 PAGE_SIZE, 1400 DMA_FROM_DEVICE); 1401 vaddr = kmap_atomic(ps_page->page); 1402 memcpy(skb_tail_pointer(skb), vaddr, l1); 1403 kunmap_atomic(vaddr); 1404 dma_sync_single_for_device(&pdev->dev, 1405 ps_page->dma, 1406 PAGE_SIZE, 1407 DMA_FROM_DEVICE); 1408 1409 /* remove the CRC */ 1410 if (!(adapter->flags2 & FLAG2_CRC_STRIPPING)) { 1411 if (!(netdev->features & NETIF_F_RXFCS)) 1412 l1 -= 4; 1413 } 1414 1415 skb_put(skb, l1); 1416 goto copydone; 1417 } /* if */ 1418 } 1419 1420 for (j = 0; j < PS_PAGE_BUFFERS; j++) { 1421 length = le16_to_cpu(rx_desc->wb.upper.length[j]); 1422 if (!length) 1423 break; 1424 1425 ps_page = &buffer_info->ps_pages[j]; 1426 dma_unmap_page(&pdev->dev, ps_page->dma, PAGE_SIZE, 1427 DMA_FROM_DEVICE); 1428 ps_page->dma = 0; 1429 skb_fill_page_desc(skb, j, ps_page->page, 0, length); 1430 ps_page->page = NULL; 1431 skb->len += length; 1432 skb->data_len += length; 1433 skb->truesize += PAGE_SIZE; 1434 } 1435 1436 /* strip the ethernet crc, problem is we're using pages now so 1437 * this whole operation can get a little cpu intensive 1438 */ 1439 if (!(adapter->flags2 & FLAG2_CRC_STRIPPING)) { 1440 if (!(netdev->features & NETIF_F_RXFCS)) 1441 pskb_trim(skb, skb->len - 4); 1442 } 1443 1444 copydone: 1445 total_rx_bytes += skb->len; 1446 total_rx_packets++; 1447 1448 e1000_rx_checksum(adapter, staterr, skb); 1449 1450 e1000_rx_hash(netdev, rx_desc->wb.lower.hi_dword.rss, skb); 1451 1452 if (rx_desc->wb.upper.header_status & 1453 cpu_to_le16(E1000_RXDPS_HDRSTAT_HDRSP)) 1454 adapter->rx_hdr_split++; 1455 1456 e1000_receive_skb(adapter, netdev, skb, staterr, 1457 rx_desc->wb.middle.vlan); 1458 1459 next_desc: 1460 rx_desc->wb.middle.status_error &= cpu_to_le32(~0xFF); 1461 buffer_info->skb = NULL; 1462 1463 /* return some buffers to hardware, one at a time is too slow */ 1464 if (cleaned_count >= E1000_RX_BUFFER_WRITE) { 1465 adapter->alloc_rx_buf(rx_ring, cleaned_count, 1466 GFP_ATOMIC); 1467 cleaned_count = 0; 1468 } 1469 1470 /* use prefetched values */ 1471 rx_desc = next_rxd; 1472 buffer_info = next_buffer; 1473 1474 staterr = le32_to_cpu(rx_desc->wb.middle.status_error); 1475 } 1476 rx_ring->next_to_clean = i; 1477 1478 cleaned_count = e1000_desc_unused(rx_ring); 1479 if (cleaned_count) 1480 adapter->alloc_rx_buf(rx_ring, cleaned_count, GFP_ATOMIC); 1481 1482 adapter->total_rx_bytes += total_rx_bytes; 1483 adapter->total_rx_packets += total_rx_packets; 1484 return cleaned; 1485 } 1486 1487 /** 1488 * e1000_consume_page - helper function 1489 **/ 1490 static void e1000_consume_page(struct e1000_buffer *bi, struct sk_buff *skb, 1491 u16 length) 1492 { 1493 bi->page = NULL; 1494 skb->len += length; 1495 skb->data_len += length; 1496 skb->truesize += PAGE_SIZE; 1497 } 1498 1499 /** 1500 * e1000_clean_jumbo_rx_irq - Send received data up the network stack; legacy 1501 * @adapter: board private structure 1502 * 1503 * the return value indicates whether actual cleaning was done, there 1504 * is no guarantee that everything was cleaned 1505 **/ 1506 static bool e1000_clean_jumbo_rx_irq(struct e1000_ring *rx_ring, int *work_done, 1507 int work_to_do) 1508 { 1509 struct e1000_adapter *adapter = rx_ring->adapter; 1510 struct net_device *netdev = adapter->netdev; 1511 struct pci_dev *pdev = adapter->pdev; 1512 union e1000_rx_desc_extended *rx_desc, *next_rxd; 1513 struct e1000_buffer *buffer_info, *next_buffer; 1514 u32 length, staterr; 1515 unsigned int i; 1516 int cleaned_count = 0; 1517 bool cleaned = false; 1518 unsigned int total_rx_bytes = 0, total_rx_packets = 0; 1519 struct skb_shared_info *shinfo; 1520 1521 i = rx_ring->next_to_clean; 1522 rx_desc = E1000_RX_DESC_EXT(*rx_ring, i); 1523 staterr = le32_to_cpu(rx_desc->wb.upper.status_error); 1524 buffer_info = &rx_ring->buffer_info[i]; 1525 1526 while (staterr & E1000_RXD_STAT_DD) { 1527 struct sk_buff *skb; 1528 1529 if (*work_done >= work_to_do) 1530 break; 1531 (*work_done)++; 1532 dma_rmb(); /* read descriptor and rx_buffer_info after status DD */ 1533 1534 skb = buffer_info->skb; 1535 buffer_info->skb = NULL; 1536 1537 ++i; 1538 if (i == rx_ring->count) 1539 i = 0; 1540 next_rxd = E1000_RX_DESC_EXT(*rx_ring, i); 1541 prefetch(next_rxd); 1542 1543 next_buffer = &rx_ring->buffer_info[i]; 1544 1545 cleaned = true; 1546 cleaned_count++; 1547 dma_unmap_page(&pdev->dev, buffer_info->dma, PAGE_SIZE, 1548 DMA_FROM_DEVICE); 1549 buffer_info->dma = 0; 1550 1551 length = le16_to_cpu(rx_desc->wb.upper.length); 1552 1553 /* errors is only valid for DD + EOP descriptors */ 1554 if (unlikely((staterr & E1000_RXD_STAT_EOP) && 1555 ((staterr & E1000_RXDEXT_ERR_FRAME_ERR_MASK) && 1556 !(netdev->features & NETIF_F_RXALL)))) { 1557 /* recycle both page and skb */ 1558 buffer_info->skb = skb; 1559 /* an error means any chain goes out the window too */ 1560 if (rx_ring->rx_skb_top) 1561 dev_kfree_skb_irq(rx_ring->rx_skb_top); 1562 rx_ring->rx_skb_top = NULL; 1563 goto next_desc; 1564 } 1565 #define rxtop (rx_ring->rx_skb_top) 1566 if (!(staterr & E1000_RXD_STAT_EOP)) { 1567 /* this descriptor is only the beginning (or middle) */ 1568 if (!rxtop) { 1569 /* this is the beginning of a chain */ 1570 rxtop = skb; 1571 skb_fill_page_desc(rxtop, 0, buffer_info->page, 1572 0, length); 1573 } else { 1574 /* this is the middle of a chain */ 1575 shinfo = skb_shinfo(rxtop); 1576 skb_fill_page_desc(rxtop, shinfo->nr_frags, 1577 buffer_info->page, 0, 1578 length); 1579 /* re-use the skb, only consumed the page */ 1580 buffer_info->skb = skb; 1581 } 1582 e1000_consume_page(buffer_info, rxtop, length); 1583 goto next_desc; 1584 } else { 1585 if (rxtop) { 1586 /* end of the chain */ 1587 shinfo = skb_shinfo(rxtop); 1588 skb_fill_page_desc(rxtop, shinfo->nr_frags, 1589 buffer_info->page, 0, 1590 length); 1591 /* re-use the current skb, we only consumed the 1592 * page 1593 */ 1594 buffer_info->skb = skb; 1595 skb = rxtop; 1596 rxtop = NULL; 1597 e1000_consume_page(buffer_info, skb, length); 1598 } else { 1599 /* no chain, got EOP, this buf is the packet 1600 * copybreak to save the put_page/alloc_page 1601 */ 1602 if (length <= copybreak && 1603 skb_tailroom(skb) >= length) { 1604 u8 *vaddr; 1605 vaddr = kmap_atomic(buffer_info->page); 1606 memcpy(skb_tail_pointer(skb), vaddr, 1607 length); 1608 kunmap_atomic(vaddr); 1609 /* re-use the page, so don't erase 1610 * buffer_info->page 1611 */ 1612 skb_put(skb, length); 1613 } else { 1614 skb_fill_page_desc(skb, 0, 1615 buffer_info->page, 0, 1616 length); 1617 e1000_consume_page(buffer_info, skb, 1618 length); 1619 } 1620 } 1621 } 1622 1623 /* Receive Checksum Offload */ 1624 e1000_rx_checksum(adapter, staterr, skb); 1625 1626 e1000_rx_hash(netdev, rx_desc->wb.lower.hi_dword.rss, skb); 1627 1628 /* probably a little skewed due to removing CRC */ 1629 total_rx_bytes += skb->len; 1630 total_rx_packets++; 1631 1632 /* eth type trans needs skb->data to point to something */ 1633 if (!pskb_may_pull(skb, ETH_HLEN)) { 1634 e_err("pskb_may_pull failed.\n"); 1635 dev_kfree_skb_irq(skb); 1636 goto next_desc; 1637 } 1638 1639 e1000_receive_skb(adapter, netdev, skb, staterr, 1640 rx_desc->wb.upper.vlan); 1641 1642 next_desc: 1643 rx_desc->wb.upper.status_error &= cpu_to_le32(~0xFF); 1644 1645 /* return some buffers to hardware, one at a time is too slow */ 1646 if (unlikely(cleaned_count >= E1000_RX_BUFFER_WRITE)) { 1647 adapter->alloc_rx_buf(rx_ring, cleaned_count, 1648 GFP_ATOMIC); 1649 cleaned_count = 0; 1650 } 1651 1652 /* use prefetched values */ 1653 rx_desc = next_rxd; 1654 buffer_info = next_buffer; 1655 1656 staterr = le32_to_cpu(rx_desc->wb.upper.status_error); 1657 } 1658 rx_ring->next_to_clean = i; 1659 1660 cleaned_count = e1000_desc_unused(rx_ring); 1661 if (cleaned_count) 1662 adapter->alloc_rx_buf(rx_ring, cleaned_count, GFP_ATOMIC); 1663 1664 adapter->total_rx_bytes += total_rx_bytes; 1665 adapter->total_rx_packets += total_rx_packets; 1666 return cleaned; 1667 } 1668 1669 /** 1670 * e1000_clean_rx_ring - Free Rx Buffers per Queue 1671 * @rx_ring: Rx descriptor ring 1672 **/ 1673 static void e1000_clean_rx_ring(struct e1000_ring *rx_ring) 1674 { 1675 struct e1000_adapter *adapter = rx_ring->adapter; 1676 struct e1000_buffer *buffer_info; 1677 struct e1000_ps_page *ps_page; 1678 struct pci_dev *pdev = adapter->pdev; 1679 unsigned int i, j; 1680 1681 /* Free all the Rx ring sk_buffs */ 1682 for (i = 0; i < rx_ring->count; i++) { 1683 buffer_info = &rx_ring->buffer_info[i]; 1684 if (buffer_info->dma) { 1685 if (adapter->clean_rx == e1000_clean_rx_irq) 1686 dma_unmap_single(&pdev->dev, buffer_info->dma, 1687 adapter->rx_buffer_len, 1688 DMA_FROM_DEVICE); 1689 else if (adapter->clean_rx == e1000_clean_jumbo_rx_irq) 1690 dma_unmap_page(&pdev->dev, buffer_info->dma, 1691 PAGE_SIZE, DMA_FROM_DEVICE); 1692 else if (adapter->clean_rx == e1000_clean_rx_irq_ps) 1693 dma_unmap_single(&pdev->dev, buffer_info->dma, 1694 adapter->rx_ps_bsize0, 1695 DMA_FROM_DEVICE); 1696 buffer_info->dma = 0; 1697 } 1698 1699 if (buffer_info->page) { 1700 put_page(buffer_info->page); 1701 buffer_info->page = NULL; 1702 } 1703 1704 if (buffer_info->skb) { 1705 dev_kfree_skb(buffer_info->skb); 1706 buffer_info->skb = NULL; 1707 } 1708 1709 for (j = 0; j < PS_PAGE_BUFFERS; j++) { 1710 ps_page = &buffer_info->ps_pages[j]; 1711 if (!ps_page->page) 1712 break; 1713 dma_unmap_page(&pdev->dev, ps_page->dma, PAGE_SIZE, 1714 DMA_FROM_DEVICE); 1715 ps_page->dma = 0; 1716 put_page(ps_page->page); 1717 ps_page->page = NULL; 1718 } 1719 } 1720 1721 /* there also may be some cached data from a chained receive */ 1722 if (rx_ring->rx_skb_top) { 1723 dev_kfree_skb(rx_ring->rx_skb_top); 1724 rx_ring->rx_skb_top = NULL; 1725 } 1726 1727 /* Zero out the descriptor ring */ 1728 memset(rx_ring->desc, 0, rx_ring->size); 1729 1730 rx_ring->next_to_clean = 0; 1731 rx_ring->next_to_use = 0; 1732 adapter->flags2 &= ~FLAG2_IS_DISCARDING; 1733 } 1734 1735 static void e1000e_downshift_workaround(struct work_struct *work) 1736 { 1737 struct e1000_adapter *adapter = container_of(work, 1738 struct e1000_adapter, 1739 downshift_task); 1740 1741 if (test_bit(__E1000_DOWN, &adapter->state)) 1742 return; 1743 1744 e1000e_gig_downshift_workaround_ich8lan(&adapter->hw); 1745 } 1746 1747 /** 1748 * e1000_intr_msi - Interrupt Handler 1749 * @irq: interrupt number 1750 * @data: pointer to a network interface device structure 1751 **/ 1752 static irqreturn_t e1000_intr_msi(int __always_unused irq, void *data) 1753 { 1754 struct net_device *netdev = data; 1755 struct e1000_adapter *adapter = netdev_priv(netdev); 1756 struct e1000_hw *hw = &adapter->hw; 1757 u32 icr = er32(ICR); 1758 1759 /* read ICR disables interrupts using IAM */ 1760 if (icr & E1000_ICR_LSC) { 1761 hw->mac.get_link_status = true; 1762 /* ICH8 workaround-- Call gig speed drop workaround on cable 1763 * disconnect (LSC) before accessing any PHY registers 1764 */ 1765 if ((adapter->flags & FLAG_LSC_GIG_SPEED_DROP) && 1766 (!(er32(STATUS) & E1000_STATUS_LU))) 1767 schedule_work(&adapter->downshift_task); 1768 1769 /* 80003ES2LAN workaround-- For packet buffer work-around on 1770 * link down event; disable receives here in the ISR and reset 1771 * adapter in watchdog 1772 */ 1773 if (netif_carrier_ok(netdev) && 1774 adapter->flags & FLAG_RX_NEEDS_RESTART) { 1775 /* disable receives */ 1776 u32 rctl = er32(RCTL); 1777 1778 ew32(RCTL, rctl & ~E1000_RCTL_EN); 1779 adapter->flags |= FLAG_RESTART_NOW; 1780 } 1781 /* guard against interrupt when we're going down */ 1782 if (!test_bit(__E1000_DOWN, &adapter->state)) 1783 mod_timer(&adapter->watchdog_timer, jiffies + 1); 1784 } 1785 1786 /* Reset on uncorrectable ECC error */ 1787 if ((icr & E1000_ICR_ECCER) && (hw->mac.type >= e1000_pch_lpt)) { 1788 u32 pbeccsts = er32(PBECCSTS); 1789 1790 adapter->corr_errors += 1791 pbeccsts & E1000_PBECCSTS_CORR_ERR_CNT_MASK; 1792 adapter->uncorr_errors += 1793 (pbeccsts & E1000_PBECCSTS_UNCORR_ERR_CNT_MASK) >> 1794 E1000_PBECCSTS_UNCORR_ERR_CNT_SHIFT; 1795 1796 /* Do the reset outside of interrupt context */ 1797 schedule_work(&adapter->reset_task); 1798 1799 /* return immediately since reset is imminent */ 1800 return IRQ_HANDLED; 1801 } 1802 1803 if (napi_schedule_prep(&adapter->napi)) { 1804 adapter->total_tx_bytes = 0; 1805 adapter->total_tx_packets = 0; 1806 adapter->total_rx_bytes = 0; 1807 adapter->total_rx_packets = 0; 1808 __napi_schedule(&adapter->napi); 1809 } 1810 1811 return IRQ_HANDLED; 1812 } 1813 1814 /** 1815 * e1000_intr - Interrupt Handler 1816 * @irq: interrupt number 1817 * @data: pointer to a network interface device structure 1818 **/ 1819 static irqreturn_t e1000_intr(int __always_unused irq, void *data) 1820 { 1821 struct net_device *netdev = data; 1822 struct e1000_adapter *adapter = netdev_priv(netdev); 1823 struct e1000_hw *hw = &adapter->hw; 1824 u32 rctl, icr = er32(ICR); 1825 1826 if (!icr || test_bit(__E1000_DOWN, &adapter->state)) 1827 return IRQ_NONE; /* Not our interrupt */ 1828 1829 /* IMS will not auto-mask if INT_ASSERTED is not set, and if it is 1830 * not set, then the adapter didn't send an interrupt 1831 */ 1832 if (!(icr & E1000_ICR_INT_ASSERTED)) 1833 return IRQ_NONE; 1834 1835 /* Interrupt Auto-Mask...upon reading ICR, 1836 * interrupts are masked. No need for the 1837 * IMC write 1838 */ 1839 1840 if (icr & E1000_ICR_LSC) { 1841 hw->mac.get_link_status = true; 1842 /* ICH8 workaround-- Call gig speed drop workaround on cable 1843 * disconnect (LSC) before accessing any PHY registers 1844 */ 1845 if ((adapter->flags & FLAG_LSC_GIG_SPEED_DROP) && 1846 (!(er32(STATUS) & E1000_STATUS_LU))) 1847 schedule_work(&adapter->downshift_task); 1848 1849 /* 80003ES2LAN workaround-- 1850 * For packet buffer work-around on link down event; 1851 * disable receives here in the ISR and 1852 * reset adapter in watchdog 1853 */ 1854 if (netif_carrier_ok(netdev) && 1855 (adapter->flags & FLAG_RX_NEEDS_RESTART)) { 1856 /* disable receives */ 1857 rctl = er32(RCTL); 1858 ew32(RCTL, rctl & ~E1000_RCTL_EN); 1859 adapter->flags |= FLAG_RESTART_NOW; 1860 } 1861 /* guard against interrupt when we're going down */ 1862 if (!test_bit(__E1000_DOWN, &adapter->state)) 1863 mod_timer(&adapter->watchdog_timer, jiffies + 1); 1864 } 1865 1866 /* Reset on uncorrectable ECC error */ 1867 if ((icr & E1000_ICR_ECCER) && (hw->mac.type >= e1000_pch_lpt)) { 1868 u32 pbeccsts = er32(PBECCSTS); 1869 1870 adapter->corr_errors += 1871 pbeccsts & E1000_PBECCSTS_CORR_ERR_CNT_MASK; 1872 adapter->uncorr_errors += 1873 (pbeccsts & E1000_PBECCSTS_UNCORR_ERR_CNT_MASK) >> 1874 E1000_PBECCSTS_UNCORR_ERR_CNT_SHIFT; 1875 1876 /* Do the reset outside of interrupt context */ 1877 schedule_work(&adapter->reset_task); 1878 1879 /* return immediately since reset is imminent */ 1880 return IRQ_HANDLED; 1881 } 1882 1883 if (napi_schedule_prep(&adapter->napi)) { 1884 adapter->total_tx_bytes = 0; 1885 adapter->total_tx_packets = 0; 1886 adapter->total_rx_bytes = 0; 1887 adapter->total_rx_packets = 0; 1888 __napi_schedule(&adapter->napi); 1889 } 1890 1891 return IRQ_HANDLED; 1892 } 1893 1894 static irqreturn_t e1000_msix_other(int __always_unused irq, void *data) 1895 { 1896 struct net_device *netdev = data; 1897 struct e1000_adapter *adapter = netdev_priv(netdev); 1898 struct e1000_hw *hw = &adapter->hw; 1899 u32 icr = er32(ICR); 1900 1901 if (icr & adapter->eiac_mask) 1902 ew32(ICS, (icr & adapter->eiac_mask)); 1903 1904 if (icr & E1000_ICR_LSC) { 1905 hw->mac.get_link_status = true; 1906 /* guard against interrupt when we're going down */ 1907 if (!test_bit(__E1000_DOWN, &adapter->state)) 1908 mod_timer(&adapter->watchdog_timer, jiffies + 1); 1909 } 1910 1911 if (!test_bit(__E1000_DOWN, &adapter->state)) 1912 ew32(IMS, E1000_IMS_OTHER | IMS_OTHER_MASK); 1913 1914 return IRQ_HANDLED; 1915 } 1916 1917 static irqreturn_t e1000_intr_msix_tx(int __always_unused irq, void *data) 1918 { 1919 struct net_device *netdev = data; 1920 struct e1000_adapter *adapter = netdev_priv(netdev); 1921 struct e1000_hw *hw = &adapter->hw; 1922 struct e1000_ring *tx_ring = adapter->tx_ring; 1923 1924 adapter->total_tx_bytes = 0; 1925 adapter->total_tx_packets = 0; 1926 1927 if (!e1000_clean_tx_irq(tx_ring)) 1928 /* Ring was not completely cleaned, so fire another interrupt */ 1929 ew32(ICS, tx_ring->ims_val); 1930 1931 if (!test_bit(__E1000_DOWN, &adapter->state)) 1932 ew32(IMS, adapter->tx_ring->ims_val); 1933 1934 return IRQ_HANDLED; 1935 } 1936 1937 static irqreturn_t e1000_intr_msix_rx(int __always_unused irq, void *data) 1938 { 1939 struct net_device *netdev = data; 1940 struct e1000_adapter *adapter = netdev_priv(netdev); 1941 struct e1000_ring *rx_ring = adapter->rx_ring; 1942 1943 /* Write the ITR value calculated at the end of the 1944 * previous interrupt. 1945 */ 1946 if (rx_ring->set_itr) { 1947 u32 itr = rx_ring->itr_val ? 1948 1000000000 / (rx_ring->itr_val * 256) : 0; 1949 1950 writel(itr, rx_ring->itr_register); 1951 rx_ring->set_itr = 0; 1952 } 1953 1954 if (napi_schedule_prep(&adapter->napi)) { 1955 adapter->total_rx_bytes = 0; 1956 adapter->total_rx_packets = 0; 1957 __napi_schedule(&adapter->napi); 1958 } 1959 return IRQ_HANDLED; 1960 } 1961 1962 /** 1963 * e1000_configure_msix - Configure MSI-X hardware 1964 * 1965 * e1000_configure_msix sets up the hardware to properly 1966 * generate MSI-X interrupts. 1967 **/ 1968 static void e1000_configure_msix(struct e1000_adapter *adapter) 1969 { 1970 struct e1000_hw *hw = &adapter->hw; 1971 struct e1000_ring *rx_ring = adapter->rx_ring; 1972 struct e1000_ring *tx_ring = adapter->tx_ring; 1973 int vector = 0; 1974 u32 ctrl_ext, ivar = 0; 1975 1976 adapter->eiac_mask = 0; 1977 1978 /* Workaround issue with spurious interrupts on 82574 in MSI-X mode */ 1979 if (hw->mac.type == e1000_82574) { 1980 u32 rfctl = er32(RFCTL); 1981 1982 rfctl |= E1000_RFCTL_ACK_DIS; 1983 ew32(RFCTL, rfctl); 1984 } 1985 1986 /* Configure Rx vector */ 1987 rx_ring->ims_val = E1000_IMS_RXQ0; 1988 adapter->eiac_mask |= rx_ring->ims_val; 1989 if (rx_ring->itr_val) 1990 writel(1000000000 / (rx_ring->itr_val * 256), 1991 rx_ring->itr_register); 1992 else 1993 writel(1, rx_ring->itr_register); 1994 ivar = E1000_IVAR_INT_ALLOC_VALID | vector; 1995 1996 /* Configure Tx vector */ 1997 tx_ring->ims_val = E1000_IMS_TXQ0; 1998 vector++; 1999 if (tx_ring->itr_val) 2000 writel(1000000000 / (tx_ring->itr_val * 256), 2001 tx_ring->itr_register); 2002 else 2003 writel(1, tx_ring->itr_register); 2004 adapter->eiac_mask |= tx_ring->ims_val; 2005 ivar |= ((E1000_IVAR_INT_ALLOC_VALID | vector) << 8); 2006 2007 /* set vector for Other Causes, e.g. link changes */ 2008 vector++; 2009 ivar |= ((E1000_IVAR_INT_ALLOC_VALID | vector) << 16); 2010 if (rx_ring->itr_val) 2011 writel(1000000000 / (rx_ring->itr_val * 256), 2012 hw->hw_addr + E1000_EITR_82574(vector)); 2013 else 2014 writel(1, hw->hw_addr + E1000_EITR_82574(vector)); 2015 2016 /* Cause Tx interrupts on every write back */ 2017 ivar |= BIT(31); 2018 2019 ew32(IVAR, ivar); 2020 2021 /* enable MSI-X PBA support */ 2022 ctrl_ext = er32(CTRL_EXT) & ~E1000_CTRL_EXT_IAME; 2023 ctrl_ext |= E1000_CTRL_EXT_PBA_CLR | E1000_CTRL_EXT_EIAME; 2024 ew32(CTRL_EXT, ctrl_ext); 2025 e1e_flush(); 2026 } 2027 2028 void e1000e_reset_interrupt_capability(struct e1000_adapter *adapter) 2029 { 2030 if (adapter->msix_entries) { 2031 pci_disable_msix(adapter->pdev); 2032 kfree(adapter->msix_entries); 2033 adapter->msix_entries = NULL; 2034 } else if (adapter->flags & FLAG_MSI_ENABLED) { 2035 pci_disable_msi(adapter->pdev); 2036 adapter->flags &= ~FLAG_MSI_ENABLED; 2037 } 2038 } 2039 2040 /** 2041 * e1000e_set_interrupt_capability - set MSI or MSI-X if supported 2042 * 2043 * Attempt to configure interrupts using the best available 2044 * capabilities of the hardware and kernel. 2045 **/ 2046 void e1000e_set_interrupt_capability(struct e1000_adapter *adapter) 2047 { 2048 int err; 2049 int i; 2050 2051 switch (adapter->int_mode) { 2052 case E1000E_INT_MODE_MSIX: 2053 if (adapter->flags & FLAG_HAS_MSIX) { 2054 adapter->num_vectors = 3; /* RxQ0, TxQ0 and other */ 2055 adapter->msix_entries = kcalloc(adapter->num_vectors, 2056 sizeof(struct 2057 msix_entry), 2058 GFP_KERNEL); 2059 if (adapter->msix_entries) { 2060 struct e1000_adapter *a = adapter; 2061 2062 for (i = 0; i < adapter->num_vectors; i++) 2063 adapter->msix_entries[i].entry = i; 2064 2065 err = pci_enable_msix_range(a->pdev, 2066 a->msix_entries, 2067 a->num_vectors, 2068 a->num_vectors); 2069 if (err > 0) 2070 return; 2071 } 2072 /* MSI-X failed, so fall through and try MSI */ 2073 e_err("Failed to initialize MSI-X interrupts. Falling back to MSI interrupts.\n"); 2074 e1000e_reset_interrupt_capability(adapter); 2075 } 2076 adapter->int_mode = E1000E_INT_MODE_MSI; 2077 /* Fall through */ 2078 case E1000E_INT_MODE_MSI: 2079 if (!pci_enable_msi(adapter->pdev)) { 2080 adapter->flags |= FLAG_MSI_ENABLED; 2081 } else { 2082 adapter->int_mode = E1000E_INT_MODE_LEGACY; 2083 e_err("Failed to initialize MSI interrupts. Falling back to legacy interrupts.\n"); 2084 } 2085 /* Fall through */ 2086 case E1000E_INT_MODE_LEGACY: 2087 /* Don't do anything; this is the system default */ 2088 break; 2089 } 2090 2091 /* store the number of vectors being used */ 2092 adapter->num_vectors = 1; 2093 } 2094 2095 /** 2096 * e1000_request_msix - Initialize MSI-X interrupts 2097 * 2098 * e1000_request_msix allocates MSI-X vectors and requests interrupts from the 2099 * kernel. 2100 **/ 2101 static int e1000_request_msix(struct e1000_adapter *adapter) 2102 { 2103 struct net_device *netdev = adapter->netdev; 2104 int err = 0, vector = 0; 2105 2106 if (strlen(netdev->name) < (IFNAMSIZ - 5)) 2107 snprintf(adapter->rx_ring->name, 2108 sizeof(adapter->rx_ring->name) - 1, 2109 "%.14s-rx-0", netdev->name); 2110 else 2111 memcpy(adapter->rx_ring->name, netdev->name, IFNAMSIZ); 2112 err = request_irq(adapter->msix_entries[vector].vector, 2113 e1000_intr_msix_rx, 0, adapter->rx_ring->name, 2114 netdev); 2115 if (err) 2116 return err; 2117 adapter->rx_ring->itr_register = adapter->hw.hw_addr + 2118 E1000_EITR_82574(vector); 2119 adapter->rx_ring->itr_val = adapter->itr; 2120 vector++; 2121 2122 if (strlen(netdev->name) < (IFNAMSIZ - 5)) 2123 snprintf(adapter->tx_ring->name, 2124 sizeof(adapter->tx_ring->name) - 1, 2125 "%.14s-tx-0", netdev->name); 2126 else 2127 memcpy(adapter->tx_ring->name, netdev->name, IFNAMSIZ); 2128 err = request_irq(adapter->msix_entries[vector].vector, 2129 e1000_intr_msix_tx, 0, adapter->tx_ring->name, 2130 netdev); 2131 if (err) 2132 return err; 2133 adapter->tx_ring->itr_register = adapter->hw.hw_addr + 2134 E1000_EITR_82574(vector); 2135 adapter->tx_ring->itr_val = adapter->itr; 2136 vector++; 2137 2138 err = request_irq(adapter->msix_entries[vector].vector, 2139 e1000_msix_other, 0, netdev->name, netdev); 2140 if (err) 2141 return err; 2142 2143 e1000_configure_msix(adapter); 2144 2145 return 0; 2146 } 2147 2148 /** 2149 * e1000_request_irq - initialize interrupts 2150 * 2151 * Attempts to configure interrupts using the best available 2152 * capabilities of the hardware and kernel. 2153 **/ 2154 static int e1000_request_irq(struct e1000_adapter *adapter) 2155 { 2156 struct net_device *netdev = adapter->netdev; 2157 int err; 2158 2159 if (adapter->msix_entries) { 2160 err = e1000_request_msix(adapter); 2161 if (!err) 2162 return err; 2163 /* fall back to MSI */ 2164 e1000e_reset_interrupt_capability(adapter); 2165 adapter->int_mode = E1000E_INT_MODE_MSI; 2166 e1000e_set_interrupt_capability(adapter); 2167 } 2168 if (adapter->flags & FLAG_MSI_ENABLED) { 2169 err = request_irq(adapter->pdev->irq, e1000_intr_msi, 0, 2170 netdev->name, netdev); 2171 if (!err) 2172 return err; 2173 2174 /* fall back to legacy interrupt */ 2175 e1000e_reset_interrupt_capability(adapter); 2176 adapter->int_mode = E1000E_INT_MODE_LEGACY; 2177 } 2178 2179 err = request_irq(adapter->pdev->irq, e1000_intr, IRQF_SHARED, 2180 netdev->name, netdev); 2181 if (err) 2182 e_err("Unable to allocate interrupt, Error: %d\n", err); 2183 2184 return err; 2185 } 2186 2187 static void e1000_free_irq(struct e1000_adapter *adapter) 2188 { 2189 struct net_device *netdev = adapter->netdev; 2190 2191 if (adapter->msix_entries) { 2192 int vector = 0; 2193 2194 free_irq(adapter->msix_entries[vector].vector, netdev); 2195 vector++; 2196 2197 free_irq(adapter->msix_entries[vector].vector, netdev); 2198 vector++; 2199 2200 /* Other Causes interrupt vector */ 2201 free_irq(adapter->msix_entries[vector].vector, netdev); 2202 return; 2203 } 2204 2205 free_irq(adapter->pdev->irq, netdev); 2206 } 2207 2208 /** 2209 * e1000_irq_disable - Mask off interrupt generation on the NIC 2210 **/ 2211 static void e1000_irq_disable(struct e1000_adapter *adapter) 2212 { 2213 struct e1000_hw *hw = &adapter->hw; 2214 2215 ew32(IMC, ~0); 2216 if (adapter->msix_entries) 2217 ew32(EIAC_82574, 0); 2218 e1e_flush(); 2219 2220 if (adapter->msix_entries) { 2221 int i; 2222 2223 for (i = 0; i < adapter->num_vectors; i++) 2224 synchronize_irq(adapter->msix_entries[i].vector); 2225 } else { 2226 synchronize_irq(adapter->pdev->irq); 2227 } 2228 } 2229 2230 /** 2231 * e1000_irq_enable - Enable default interrupt generation settings 2232 **/ 2233 static void e1000_irq_enable(struct e1000_adapter *adapter) 2234 { 2235 struct e1000_hw *hw = &adapter->hw; 2236 2237 if (adapter->msix_entries) { 2238 ew32(EIAC_82574, adapter->eiac_mask & E1000_EIAC_MASK_82574); 2239 ew32(IMS, adapter->eiac_mask | E1000_IMS_OTHER | 2240 IMS_OTHER_MASK); 2241 } else if (hw->mac.type >= e1000_pch_lpt) { 2242 ew32(IMS, IMS_ENABLE_MASK | E1000_IMS_ECCER); 2243 } else { 2244 ew32(IMS, IMS_ENABLE_MASK); 2245 } 2246 e1e_flush(); 2247 } 2248 2249 /** 2250 * e1000e_get_hw_control - get control of the h/w from f/w 2251 * @adapter: address of board private structure 2252 * 2253 * e1000e_get_hw_control sets {CTRL_EXT|SWSM}:DRV_LOAD bit. 2254 * For ASF and Pass Through versions of f/w this means that 2255 * the driver is loaded. For AMT version (only with 82573) 2256 * of the f/w this means that the network i/f is open. 2257 **/ 2258 void e1000e_get_hw_control(struct e1000_adapter *adapter) 2259 { 2260 struct e1000_hw *hw = &adapter->hw; 2261 u32 ctrl_ext; 2262 u32 swsm; 2263 2264 /* Let firmware know the driver has taken over */ 2265 if (adapter->flags & FLAG_HAS_SWSM_ON_LOAD) { 2266 swsm = er32(SWSM); 2267 ew32(SWSM, swsm | E1000_SWSM_DRV_LOAD); 2268 } else if (adapter->flags & FLAG_HAS_CTRLEXT_ON_LOAD) { 2269 ctrl_ext = er32(CTRL_EXT); 2270 ew32(CTRL_EXT, ctrl_ext | E1000_CTRL_EXT_DRV_LOAD); 2271 } 2272 } 2273 2274 /** 2275 * e1000e_release_hw_control - release control of the h/w to f/w 2276 * @adapter: address of board private structure 2277 * 2278 * e1000e_release_hw_control resets {CTRL_EXT|SWSM}:DRV_LOAD bit. 2279 * For ASF and Pass Through versions of f/w this means that the 2280 * driver is no longer loaded. For AMT version (only with 82573) i 2281 * of the f/w this means that the network i/f is closed. 2282 * 2283 **/ 2284 void e1000e_release_hw_control(struct e1000_adapter *adapter) 2285 { 2286 struct e1000_hw *hw = &adapter->hw; 2287 u32 ctrl_ext; 2288 u32 swsm; 2289 2290 /* Let firmware taken over control of h/w */ 2291 if (adapter->flags & FLAG_HAS_SWSM_ON_LOAD) { 2292 swsm = er32(SWSM); 2293 ew32(SWSM, swsm & ~E1000_SWSM_DRV_LOAD); 2294 } else if (adapter->flags & FLAG_HAS_CTRLEXT_ON_LOAD) { 2295 ctrl_ext = er32(CTRL_EXT); 2296 ew32(CTRL_EXT, ctrl_ext & ~E1000_CTRL_EXT_DRV_LOAD); 2297 } 2298 } 2299 2300 /** 2301 * e1000_alloc_ring_dma - allocate memory for a ring structure 2302 **/ 2303 static int e1000_alloc_ring_dma(struct e1000_adapter *adapter, 2304 struct e1000_ring *ring) 2305 { 2306 struct pci_dev *pdev = adapter->pdev; 2307 2308 ring->desc = dma_alloc_coherent(&pdev->dev, ring->size, &ring->dma, 2309 GFP_KERNEL); 2310 if (!ring->desc) 2311 return -ENOMEM; 2312 2313 return 0; 2314 } 2315 2316 /** 2317 * e1000e_setup_tx_resources - allocate Tx resources (Descriptors) 2318 * @tx_ring: Tx descriptor ring 2319 * 2320 * Return 0 on success, negative on failure 2321 **/ 2322 int e1000e_setup_tx_resources(struct e1000_ring *tx_ring) 2323 { 2324 struct e1000_adapter *adapter = tx_ring->adapter; 2325 int err = -ENOMEM, size; 2326 2327 size = sizeof(struct e1000_buffer) * tx_ring->count; 2328 tx_ring->buffer_info = vzalloc(size); 2329 if (!tx_ring->buffer_info) 2330 goto err; 2331 2332 /* round up to nearest 4K */ 2333 tx_ring->size = tx_ring->count * sizeof(struct e1000_tx_desc); 2334 tx_ring->size = ALIGN(tx_ring->size, 4096); 2335 2336 err = e1000_alloc_ring_dma(adapter, tx_ring); 2337 if (err) 2338 goto err; 2339 2340 tx_ring->next_to_use = 0; 2341 tx_ring->next_to_clean = 0; 2342 2343 return 0; 2344 err: 2345 vfree(tx_ring->buffer_info); 2346 e_err("Unable to allocate memory for the transmit descriptor ring\n"); 2347 return err; 2348 } 2349 2350 /** 2351 * e1000e_setup_rx_resources - allocate Rx resources (Descriptors) 2352 * @rx_ring: Rx descriptor ring 2353 * 2354 * Returns 0 on success, negative on failure 2355 **/ 2356 int e1000e_setup_rx_resources(struct e1000_ring *rx_ring) 2357 { 2358 struct e1000_adapter *adapter = rx_ring->adapter; 2359 struct e1000_buffer *buffer_info; 2360 int i, size, desc_len, err = -ENOMEM; 2361 2362 size = sizeof(struct e1000_buffer) * rx_ring->count; 2363 rx_ring->buffer_info = vzalloc(size); 2364 if (!rx_ring->buffer_info) 2365 goto err; 2366 2367 for (i = 0; i < rx_ring->count; i++) { 2368 buffer_info = &rx_ring->buffer_info[i]; 2369 buffer_info->ps_pages = kcalloc(PS_PAGE_BUFFERS, 2370 sizeof(struct e1000_ps_page), 2371 GFP_KERNEL); 2372 if (!buffer_info->ps_pages) 2373 goto err_pages; 2374 } 2375 2376 desc_len = sizeof(union e1000_rx_desc_packet_split); 2377 2378 /* Round up to nearest 4K */ 2379 rx_ring->size = rx_ring->count * desc_len; 2380 rx_ring->size = ALIGN(rx_ring->size, 4096); 2381 2382 err = e1000_alloc_ring_dma(adapter, rx_ring); 2383 if (err) 2384 goto err_pages; 2385 2386 rx_ring->next_to_clean = 0; 2387 rx_ring->next_to_use = 0; 2388 rx_ring->rx_skb_top = NULL; 2389 2390 return 0; 2391 2392 err_pages: 2393 for (i = 0; i < rx_ring->count; i++) { 2394 buffer_info = &rx_ring->buffer_info[i]; 2395 kfree(buffer_info->ps_pages); 2396 } 2397 err: 2398 vfree(rx_ring->buffer_info); 2399 e_err("Unable to allocate memory for the receive descriptor ring\n"); 2400 return err; 2401 } 2402 2403 /** 2404 * e1000_clean_tx_ring - Free Tx Buffers 2405 * @tx_ring: Tx descriptor ring 2406 **/ 2407 static void e1000_clean_tx_ring(struct e1000_ring *tx_ring) 2408 { 2409 struct e1000_adapter *adapter = tx_ring->adapter; 2410 struct e1000_buffer *buffer_info; 2411 unsigned long size; 2412 unsigned int i; 2413 2414 for (i = 0; i < tx_ring->count; i++) { 2415 buffer_info = &tx_ring->buffer_info[i]; 2416 e1000_put_txbuf(tx_ring, buffer_info, false); 2417 } 2418 2419 netdev_reset_queue(adapter->netdev); 2420 size = sizeof(struct e1000_buffer) * tx_ring->count; 2421 memset(tx_ring->buffer_info, 0, size); 2422 2423 memset(tx_ring->desc, 0, tx_ring->size); 2424 2425 tx_ring->next_to_use = 0; 2426 tx_ring->next_to_clean = 0; 2427 } 2428 2429 /** 2430 * e1000e_free_tx_resources - Free Tx Resources per Queue 2431 * @tx_ring: Tx descriptor ring 2432 * 2433 * Free all transmit software resources 2434 **/ 2435 void e1000e_free_tx_resources(struct e1000_ring *tx_ring) 2436 { 2437 struct e1000_adapter *adapter = tx_ring->adapter; 2438 struct pci_dev *pdev = adapter->pdev; 2439 2440 e1000_clean_tx_ring(tx_ring); 2441 2442 vfree(tx_ring->buffer_info); 2443 tx_ring->buffer_info = NULL; 2444 2445 dma_free_coherent(&pdev->dev, tx_ring->size, tx_ring->desc, 2446 tx_ring->dma); 2447 tx_ring->desc = NULL; 2448 } 2449 2450 /** 2451 * e1000e_free_rx_resources - Free Rx Resources 2452 * @rx_ring: Rx descriptor ring 2453 * 2454 * Free all receive software resources 2455 **/ 2456 void e1000e_free_rx_resources(struct e1000_ring *rx_ring) 2457 { 2458 struct e1000_adapter *adapter = rx_ring->adapter; 2459 struct pci_dev *pdev = adapter->pdev; 2460 int i; 2461 2462 e1000_clean_rx_ring(rx_ring); 2463 2464 for (i = 0; i < rx_ring->count; i++) 2465 kfree(rx_ring->buffer_info[i].ps_pages); 2466 2467 vfree(rx_ring->buffer_info); 2468 rx_ring->buffer_info = NULL; 2469 2470 dma_free_coherent(&pdev->dev, rx_ring->size, rx_ring->desc, 2471 rx_ring->dma); 2472 rx_ring->desc = NULL; 2473 } 2474 2475 /** 2476 * e1000_update_itr - update the dynamic ITR value based on statistics 2477 * @adapter: pointer to adapter 2478 * @itr_setting: current adapter->itr 2479 * @packets: the number of packets during this measurement interval 2480 * @bytes: the number of bytes during this measurement interval 2481 * 2482 * Stores a new ITR value based on packets and byte 2483 * counts during the last interrupt. The advantage of per interrupt 2484 * computation is faster updates and more accurate ITR for the current 2485 * traffic pattern. Constants in this function were computed 2486 * based on theoretical maximum wire speed and thresholds were set based 2487 * on testing data as well as attempting to minimize response time 2488 * while increasing bulk throughput. This functionality is controlled 2489 * by the InterruptThrottleRate module parameter. 2490 **/ 2491 static unsigned int e1000_update_itr(u16 itr_setting, int packets, int bytes) 2492 { 2493 unsigned int retval = itr_setting; 2494 2495 if (packets == 0) 2496 return itr_setting; 2497 2498 switch (itr_setting) { 2499 case lowest_latency: 2500 /* handle TSO and jumbo frames */ 2501 if (bytes / packets > 8000) 2502 retval = bulk_latency; 2503 else if ((packets < 5) && (bytes > 512)) 2504 retval = low_latency; 2505 break; 2506 case low_latency: /* 50 usec aka 20000 ints/s */ 2507 if (bytes > 10000) { 2508 /* this if handles the TSO accounting */ 2509 if (bytes / packets > 8000) 2510 retval = bulk_latency; 2511 else if ((packets < 10) || ((bytes / packets) > 1200)) 2512 retval = bulk_latency; 2513 else if ((packets > 35)) 2514 retval = lowest_latency; 2515 } else if (bytes / packets > 2000) { 2516 retval = bulk_latency; 2517 } else if (packets <= 2 && bytes < 512) { 2518 retval = lowest_latency; 2519 } 2520 break; 2521 case bulk_latency: /* 250 usec aka 4000 ints/s */ 2522 if (bytes > 25000) { 2523 if (packets > 35) 2524 retval = low_latency; 2525 } else if (bytes < 6000) { 2526 retval = low_latency; 2527 } 2528 break; 2529 } 2530 2531 return retval; 2532 } 2533 2534 static void e1000_set_itr(struct e1000_adapter *adapter) 2535 { 2536 u16 current_itr; 2537 u32 new_itr = adapter->itr; 2538 2539 /* for non-gigabit speeds, just fix the interrupt rate at 4000 */ 2540 if (adapter->link_speed != SPEED_1000) { 2541 current_itr = 0; 2542 new_itr = 4000; 2543 goto set_itr_now; 2544 } 2545 2546 if (adapter->flags2 & FLAG2_DISABLE_AIM) { 2547 new_itr = 0; 2548 goto set_itr_now; 2549 } 2550 2551 adapter->tx_itr = e1000_update_itr(adapter->tx_itr, 2552 adapter->total_tx_packets, 2553 adapter->total_tx_bytes); 2554 /* conservative mode (itr 3) eliminates the lowest_latency setting */ 2555 if (adapter->itr_setting == 3 && adapter->tx_itr == lowest_latency) 2556 adapter->tx_itr = low_latency; 2557 2558 adapter->rx_itr = e1000_update_itr(adapter->rx_itr, 2559 adapter->total_rx_packets, 2560 adapter->total_rx_bytes); 2561 /* conservative mode (itr 3) eliminates the lowest_latency setting */ 2562 if (adapter->itr_setting == 3 && adapter->rx_itr == lowest_latency) 2563 adapter->rx_itr = low_latency; 2564 2565 current_itr = max(adapter->rx_itr, adapter->tx_itr); 2566 2567 /* counts and packets in update_itr are dependent on these numbers */ 2568 switch (current_itr) { 2569 case lowest_latency: 2570 new_itr = 70000; 2571 break; 2572 case low_latency: 2573 new_itr = 20000; /* aka hwitr = ~200 */ 2574 break; 2575 case bulk_latency: 2576 new_itr = 4000; 2577 break; 2578 default: 2579 break; 2580 } 2581 2582 set_itr_now: 2583 if (new_itr != adapter->itr) { 2584 /* this attempts to bias the interrupt rate towards Bulk 2585 * by adding intermediate steps when interrupt rate is 2586 * increasing 2587 */ 2588 new_itr = new_itr > adapter->itr ? 2589 min(adapter->itr + (new_itr >> 2), new_itr) : new_itr; 2590 adapter->itr = new_itr; 2591 adapter->rx_ring->itr_val = new_itr; 2592 if (adapter->msix_entries) 2593 adapter->rx_ring->set_itr = 1; 2594 else 2595 e1000e_write_itr(adapter, new_itr); 2596 } 2597 } 2598 2599 /** 2600 * e1000e_write_itr - write the ITR value to the appropriate registers 2601 * @adapter: address of board private structure 2602 * @itr: new ITR value to program 2603 * 2604 * e1000e_write_itr determines if the adapter is in MSI-X mode 2605 * and, if so, writes the EITR registers with the ITR value. 2606 * Otherwise, it writes the ITR value into the ITR register. 2607 **/ 2608 void e1000e_write_itr(struct e1000_adapter *adapter, u32 itr) 2609 { 2610 struct e1000_hw *hw = &adapter->hw; 2611 u32 new_itr = itr ? 1000000000 / (itr * 256) : 0; 2612 2613 if (adapter->msix_entries) { 2614 int vector; 2615 2616 for (vector = 0; vector < adapter->num_vectors; vector++) 2617 writel(new_itr, hw->hw_addr + E1000_EITR_82574(vector)); 2618 } else { 2619 ew32(ITR, new_itr); 2620 } 2621 } 2622 2623 /** 2624 * e1000_alloc_queues - Allocate memory for all rings 2625 * @adapter: board private structure to initialize 2626 **/ 2627 static int e1000_alloc_queues(struct e1000_adapter *adapter) 2628 { 2629 int size = sizeof(struct e1000_ring); 2630 2631 adapter->tx_ring = kzalloc(size, GFP_KERNEL); 2632 if (!adapter->tx_ring) 2633 goto err; 2634 adapter->tx_ring->count = adapter->tx_ring_count; 2635 adapter->tx_ring->adapter = adapter; 2636 2637 adapter->rx_ring = kzalloc(size, GFP_KERNEL); 2638 if (!adapter->rx_ring) 2639 goto err; 2640 adapter->rx_ring->count = adapter->rx_ring_count; 2641 adapter->rx_ring->adapter = adapter; 2642 2643 return 0; 2644 err: 2645 e_err("Unable to allocate memory for queues\n"); 2646 kfree(adapter->rx_ring); 2647 kfree(adapter->tx_ring); 2648 return -ENOMEM; 2649 } 2650 2651 /** 2652 * e1000e_poll - NAPI Rx polling callback 2653 * @napi: struct associated with this polling callback 2654 * @budget: number of packets driver is allowed to process this poll 2655 **/ 2656 static int e1000e_poll(struct napi_struct *napi, int budget) 2657 { 2658 struct e1000_adapter *adapter = container_of(napi, struct e1000_adapter, 2659 napi); 2660 struct e1000_hw *hw = &adapter->hw; 2661 struct net_device *poll_dev = adapter->netdev; 2662 int tx_cleaned = 1, work_done = 0; 2663 2664 adapter = netdev_priv(poll_dev); 2665 2666 if (!adapter->msix_entries || 2667 (adapter->rx_ring->ims_val & adapter->tx_ring->ims_val)) 2668 tx_cleaned = e1000_clean_tx_irq(adapter->tx_ring); 2669 2670 adapter->clean_rx(adapter->rx_ring, &work_done, budget); 2671 2672 if (!tx_cleaned || work_done == budget) 2673 return budget; 2674 2675 /* Exit the polling mode, but don't re-enable interrupts if stack might 2676 * poll us due to busy-polling 2677 */ 2678 if (likely(napi_complete_done(napi, work_done))) { 2679 if (adapter->itr_setting & 3) 2680 e1000_set_itr(adapter); 2681 if (!test_bit(__E1000_DOWN, &adapter->state)) { 2682 if (adapter->msix_entries) 2683 ew32(IMS, adapter->rx_ring->ims_val); 2684 else 2685 e1000_irq_enable(adapter); 2686 } 2687 } 2688 2689 return work_done; 2690 } 2691 2692 static int e1000_vlan_rx_add_vid(struct net_device *netdev, 2693 __always_unused __be16 proto, u16 vid) 2694 { 2695 struct e1000_adapter *adapter = netdev_priv(netdev); 2696 struct e1000_hw *hw = &adapter->hw; 2697 u32 vfta, index; 2698 2699 /* don't update vlan cookie if already programmed */ 2700 if ((adapter->hw.mng_cookie.status & 2701 E1000_MNG_DHCP_COOKIE_STATUS_VLAN) && 2702 (vid == adapter->mng_vlan_id)) 2703 return 0; 2704 2705 /* add VID to filter table */ 2706 if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) { 2707 index = (vid >> 5) & 0x7F; 2708 vfta = E1000_READ_REG_ARRAY(hw, E1000_VFTA, index); 2709 vfta |= BIT((vid & 0x1F)); 2710 hw->mac.ops.write_vfta(hw, index, vfta); 2711 } 2712 2713 set_bit(vid, adapter->active_vlans); 2714 2715 return 0; 2716 } 2717 2718 static int e1000_vlan_rx_kill_vid(struct net_device *netdev, 2719 __always_unused __be16 proto, u16 vid) 2720 { 2721 struct e1000_adapter *adapter = netdev_priv(netdev); 2722 struct e1000_hw *hw = &adapter->hw; 2723 u32 vfta, index; 2724 2725 if ((adapter->hw.mng_cookie.status & 2726 E1000_MNG_DHCP_COOKIE_STATUS_VLAN) && 2727 (vid == adapter->mng_vlan_id)) { 2728 /* release control to f/w */ 2729 e1000e_release_hw_control(adapter); 2730 return 0; 2731 } 2732 2733 /* remove VID from filter table */ 2734 if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) { 2735 index = (vid >> 5) & 0x7F; 2736 vfta = E1000_READ_REG_ARRAY(hw, E1000_VFTA, index); 2737 vfta &= ~BIT((vid & 0x1F)); 2738 hw->mac.ops.write_vfta(hw, index, vfta); 2739 } 2740 2741 clear_bit(vid, adapter->active_vlans); 2742 2743 return 0; 2744 } 2745 2746 /** 2747 * e1000e_vlan_filter_disable - helper to disable hw VLAN filtering 2748 * @adapter: board private structure to initialize 2749 **/ 2750 static void e1000e_vlan_filter_disable(struct e1000_adapter *adapter) 2751 { 2752 struct net_device *netdev = adapter->netdev; 2753 struct e1000_hw *hw = &adapter->hw; 2754 u32 rctl; 2755 2756 if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) { 2757 /* disable VLAN receive filtering */ 2758 rctl = er32(RCTL); 2759 rctl &= ~(E1000_RCTL_VFE | E1000_RCTL_CFIEN); 2760 ew32(RCTL, rctl); 2761 2762 if (adapter->mng_vlan_id != (u16)E1000_MNG_VLAN_NONE) { 2763 e1000_vlan_rx_kill_vid(netdev, htons(ETH_P_8021Q), 2764 adapter->mng_vlan_id); 2765 adapter->mng_vlan_id = E1000_MNG_VLAN_NONE; 2766 } 2767 } 2768 } 2769 2770 /** 2771 * e1000e_vlan_filter_enable - helper to enable HW VLAN filtering 2772 * @adapter: board private structure to initialize 2773 **/ 2774 static void e1000e_vlan_filter_enable(struct e1000_adapter *adapter) 2775 { 2776 struct e1000_hw *hw = &adapter->hw; 2777 u32 rctl; 2778 2779 if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) { 2780 /* enable VLAN receive filtering */ 2781 rctl = er32(RCTL); 2782 rctl |= E1000_RCTL_VFE; 2783 rctl &= ~E1000_RCTL_CFIEN; 2784 ew32(RCTL, rctl); 2785 } 2786 } 2787 2788 /** 2789 * e1000e_vlan_strip_disable - helper to disable HW VLAN stripping 2790 * @adapter: board private structure to initialize 2791 **/ 2792 static void e1000e_vlan_strip_disable(struct e1000_adapter *adapter) 2793 { 2794 struct e1000_hw *hw = &adapter->hw; 2795 u32 ctrl; 2796 2797 /* disable VLAN tag insert/strip */ 2798 ctrl = er32(CTRL); 2799 ctrl &= ~E1000_CTRL_VME; 2800 ew32(CTRL, ctrl); 2801 } 2802 2803 /** 2804 * e1000e_vlan_strip_enable - helper to enable HW VLAN stripping 2805 * @adapter: board private structure to initialize 2806 **/ 2807 static void e1000e_vlan_strip_enable(struct e1000_adapter *adapter) 2808 { 2809 struct e1000_hw *hw = &adapter->hw; 2810 u32 ctrl; 2811 2812 /* enable VLAN tag insert/strip */ 2813 ctrl = er32(CTRL); 2814 ctrl |= E1000_CTRL_VME; 2815 ew32(CTRL, ctrl); 2816 } 2817 2818 static void e1000_update_mng_vlan(struct e1000_adapter *adapter) 2819 { 2820 struct net_device *netdev = adapter->netdev; 2821 u16 vid = adapter->hw.mng_cookie.vlan_id; 2822 u16 old_vid = adapter->mng_vlan_id; 2823 2824 if (adapter->hw.mng_cookie.status & E1000_MNG_DHCP_COOKIE_STATUS_VLAN) { 2825 e1000_vlan_rx_add_vid(netdev, htons(ETH_P_8021Q), vid); 2826 adapter->mng_vlan_id = vid; 2827 } 2828 2829 if ((old_vid != (u16)E1000_MNG_VLAN_NONE) && (vid != old_vid)) 2830 e1000_vlan_rx_kill_vid(netdev, htons(ETH_P_8021Q), old_vid); 2831 } 2832 2833 static void e1000_restore_vlan(struct e1000_adapter *adapter) 2834 { 2835 u16 vid; 2836 2837 e1000_vlan_rx_add_vid(adapter->netdev, htons(ETH_P_8021Q), 0); 2838 2839 for_each_set_bit(vid, adapter->active_vlans, VLAN_N_VID) 2840 e1000_vlan_rx_add_vid(adapter->netdev, htons(ETH_P_8021Q), vid); 2841 } 2842 2843 static void e1000_init_manageability_pt(struct e1000_adapter *adapter) 2844 { 2845 struct e1000_hw *hw = &adapter->hw; 2846 u32 manc, manc2h, mdef, i, j; 2847 2848 if (!(adapter->flags & FLAG_MNG_PT_ENABLED)) 2849 return; 2850 2851 manc = er32(MANC); 2852 2853 /* enable receiving management packets to the host. this will probably 2854 * generate destination unreachable messages from the host OS, but 2855 * the packets will be handled on SMBUS 2856 */ 2857 manc |= E1000_MANC_EN_MNG2HOST; 2858 manc2h = er32(MANC2H); 2859 2860 switch (hw->mac.type) { 2861 default: 2862 manc2h |= (E1000_MANC2H_PORT_623 | E1000_MANC2H_PORT_664); 2863 break; 2864 case e1000_82574: 2865 case e1000_82583: 2866 /* Check if IPMI pass-through decision filter already exists; 2867 * if so, enable it. 2868 */ 2869 for (i = 0, j = 0; i < 8; i++) { 2870 mdef = er32(MDEF(i)); 2871 2872 /* Ignore filters with anything other than IPMI ports */ 2873 if (mdef & ~(E1000_MDEF_PORT_623 | E1000_MDEF_PORT_664)) 2874 continue; 2875 2876 /* Enable this decision filter in MANC2H */ 2877 if (mdef) 2878 manc2h |= BIT(i); 2879 2880 j |= mdef; 2881 } 2882 2883 if (j == (E1000_MDEF_PORT_623 | E1000_MDEF_PORT_664)) 2884 break; 2885 2886 /* Create new decision filter in an empty filter */ 2887 for (i = 0, j = 0; i < 8; i++) 2888 if (er32(MDEF(i)) == 0) { 2889 ew32(MDEF(i), (E1000_MDEF_PORT_623 | 2890 E1000_MDEF_PORT_664)); 2891 manc2h |= BIT(1); 2892 j++; 2893 break; 2894 } 2895 2896 if (!j) 2897 e_warn("Unable to create IPMI pass-through filter\n"); 2898 break; 2899 } 2900 2901 ew32(MANC2H, manc2h); 2902 ew32(MANC, manc); 2903 } 2904 2905 /** 2906 * e1000_configure_tx - Configure Transmit Unit after Reset 2907 * @adapter: board private structure 2908 * 2909 * Configure the Tx unit of the MAC after a reset. 2910 **/ 2911 static void e1000_configure_tx(struct e1000_adapter *adapter) 2912 { 2913 struct e1000_hw *hw = &adapter->hw; 2914 struct e1000_ring *tx_ring = adapter->tx_ring; 2915 u64 tdba; 2916 u32 tdlen, tctl, tarc; 2917 2918 /* Setup the HW Tx Head and Tail descriptor pointers */ 2919 tdba = tx_ring->dma; 2920 tdlen = tx_ring->count * sizeof(struct e1000_tx_desc); 2921 ew32(TDBAL(0), (tdba & DMA_BIT_MASK(32))); 2922 ew32(TDBAH(0), (tdba >> 32)); 2923 ew32(TDLEN(0), tdlen); 2924 ew32(TDH(0), 0); 2925 ew32(TDT(0), 0); 2926 tx_ring->head = adapter->hw.hw_addr + E1000_TDH(0); 2927 tx_ring->tail = adapter->hw.hw_addr + E1000_TDT(0); 2928 2929 writel(0, tx_ring->head); 2930 if (adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA) 2931 e1000e_update_tdt_wa(tx_ring, 0); 2932 else 2933 writel(0, tx_ring->tail); 2934 2935 /* Set the Tx Interrupt Delay register */ 2936 ew32(TIDV, adapter->tx_int_delay); 2937 /* Tx irq moderation */ 2938 ew32(TADV, adapter->tx_abs_int_delay); 2939 2940 if (adapter->flags2 & FLAG2_DMA_BURST) { 2941 u32 txdctl = er32(TXDCTL(0)); 2942 2943 txdctl &= ~(E1000_TXDCTL_PTHRESH | E1000_TXDCTL_HTHRESH | 2944 E1000_TXDCTL_WTHRESH); 2945 /* set up some performance related parameters to encourage the 2946 * hardware to use the bus more efficiently in bursts, depends 2947 * on the tx_int_delay to be enabled, 2948 * wthresh = 1 ==> burst write is disabled to avoid Tx stalls 2949 * hthresh = 1 ==> prefetch when one or more available 2950 * pthresh = 0x1f ==> prefetch if internal cache 31 or less 2951 * BEWARE: this seems to work but should be considered first if 2952 * there are Tx hangs or other Tx related bugs 2953 */ 2954 txdctl |= E1000_TXDCTL_DMA_BURST_ENABLE; 2955 ew32(TXDCTL(0), txdctl); 2956 } 2957 /* erratum work around: set txdctl the same for both queues */ 2958 ew32(TXDCTL(1), er32(TXDCTL(0))); 2959 2960 /* Program the Transmit Control Register */ 2961 tctl = er32(TCTL); 2962 tctl &= ~E1000_TCTL_CT; 2963 tctl |= E1000_TCTL_PSP | E1000_TCTL_RTLC | 2964 (E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT); 2965 2966 if (adapter->flags & FLAG_TARC_SPEED_MODE_BIT) { 2967 tarc = er32(TARC(0)); 2968 /* set the speed mode bit, we'll clear it if we're not at 2969 * gigabit link later 2970 */ 2971 #define SPEED_MODE_BIT BIT(21) 2972 tarc |= SPEED_MODE_BIT; 2973 ew32(TARC(0), tarc); 2974 } 2975 2976 /* errata: program both queues to unweighted RR */ 2977 if (adapter->flags & FLAG_TARC_SET_BIT_ZERO) { 2978 tarc = er32(TARC(0)); 2979 tarc |= 1; 2980 ew32(TARC(0), tarc); 2981 tarc = er32(TARC(1)); 2982 tarc |= 1; 2983 ew32(TARC(1), tarc); 2984 } 2985 2986 /* Setup Transmit Descriptor Settings for eop descriptor */ 2987 adapter->txd_cmd = E1000_TXD_CMD_EOP | E1000_TXD_CMD_IFCS; 2988 2989 /* only set IDE if we are delaying interrupts using the timers */ 2990 if (adapter->tx_int_delay) 2991 adapter->txd_cmd |= E1000_TXD_CMD_IDE; 2992 2993 /* enable Report Status bit */ 2994 adapter->txd_cmd |= E1000_TXD_CMD_RS; 2995 2996 ew32(TCTL, tctl); 2997 2998 hw->mac.ops.config_collision_dist(hw); 2999 3000 /* SPT and KBL Si errata workaround to avoid data corruption */ 3001 if (hw->mac.type == e1000_pch_spt) { 3002 u32 reg_val; 3003 3004 reg_val = er32(IOSFPC); 3005 reg_val |= E1000_RCTL_RDMTS_HEX; 3006 ew32(IOSFPC, reg_val); 3007 3008 reg_val = er32(TARC(0)); 3009 /* SPT and KBL Si errata workaround to avoid Tx hang. 3010 * Dropping the number of outstanding requests from 3011 * 3 to 2 in order to avoid a buffer overrun. 3012 */ 3013 reg_val &= ~E1000_TARC0_CB_MULTIQ_3_REQ; 3014 reg_val |= E1000_TARC0_CB_MULTIQ_2_REQ; 3015 ew32(TARC(0), reg_val); 3016 } 3017 } 3018 3019 /** 3020 * e1000_setup_rctl - configure the receive control registers 3021 * @adapter: Board private structure 3022 **/ 3023 #define PAGE_USE_COUNT(S) (((S) >> PAGE_SHIFT) + \ 3024 (((S) & (PAGE_SIZE - 1)) ? 1 : 0)) 3025 static void e1000_setup_rctl(struct e1000_adapter *adapter) 3026 { 3027 struct e1000_hw *hw = &adapter->hw; 3028 u32 rctl, rfctl; 3029 u32 pages = 0; 3030 3031 /* Workaround Si errata on PCHx - configure jumbo frame flow. 3032 * If jumbo frames not set, program related MAC/PHY registers 3033 * to h/w defaults 3034 */ 3035 if (hw->mac.type >= e1000_pch2lan) { 3036 s32 ret_val; 3037 3038 if (adapter->netdev->mtu > ETH_DATA_LEN) 3039 ret_val = e1000_lv_jumbo_workaround_ich8lan(hw, true); 3040 else 3041 ret_val = e1000_lv_jumbo_workaround_ich8lan(hw, false); 3042 3043 if (ret_val) 3044 e_dbg("failed to enable|disable jumbo frame workaround mode\n"); 3045 } 3046 3047 /* Program MC offset vector base */ 3048 rctl = er32(RCTL); 3049 rctl &= ~(3 << E1000_RCTL_MO_SHIFT); 3050 rctl |= E1000_RCTL_EN | E1000_RCTL_BAM | 3051 E1000_RCTL_LBM_NO | E1000_RCTL_RDMTS_HALF | 3052 (adapter->hw.mac.mc_filter_type << E1000_RCTL_MO_SHIFT); 3053 3054 /* Do not Store bad packets */ 3055 rctl &= ~E1000_RCTL_SBP; 3056 3057 /* Enable Long Packet receive */ 3058 if (adapter->netdev->mtu <= ETH_DATA_LEN) 3059 rctl &= ~E1000_RCTL_LPE; 3060 else 3061 rctl |= E1000_RCTL_LPE; 3062 3063 /* Some systems expect that the CRC is included in SMBUS traffic. The 3064 * hardware strips the CRC before sending to both SMBUS (BMC) and to 3065 * host memory when this is enabled 3066 */ 3067 if (adapter->flags2 & FLAG2_CRC_STRIPPING) 3068 rctl |= E1000_RCTL_SECRC; 3069 3070 /* Workaround Si errata on 82577 PHY - configure IPG for jumbos */ 3071 if ((hw->phy.type == e1000_phy_82577) && (rctl & E1000_RCTL_LPE)) { 3072 u16 phy_data; 3073 3074 e1e_rphy(hw, PHY_REG(770, 26), &phy_data); 3075 phy_data &= 0xfff8; 3076 phy_data |= BIT(2); 3077 e1e_wphy(hw, PHY_REG(770, 26), phy_data); 3078 3079 e1e_rphy(hw, 22, &phy_data); 3080 phy_data &= 0x0fff; 3081 phy_data |= BIT(14); 3082 e1e_wphy(hw, 0x10, 0x2823); 3083 e1e_wphy(hw, 0x11, 0x0003); 3084 e1e_wphy(hw, 22, phy_data); 3085 } 3086 3087 /* Setup buffer sizes */ 3088 rctl &= ~E1000_RCTL_SZ_4096; 3089 rctl |= E1000_RCTL_BSEX; 3090 switch (adapter->rx_buffer_len) { 3091 case 2048: 3092 default: 3093 rctl |= E1000_RCTL_SZ_2048; 3094 rctl &= ~E1000_RCTL_BSEX; 3095 break; 3096 case 4096: 3097 rctl |= E1000_RCTL_SZ_4096; 3098 break; 3099 case 8192: 3100 rctl |= E1000_RCTL_SZ_8192; 3101 break; 3102 case 16384: 3103 rctl |= E1000_RCTL_SZ_16384; 3104 break; 3105 } 3106 3107 /* Enable Extended Status in all Receive Descriptors */ 3108 rfctl = er32(RFCTL); 3109 rfctl |= E1000_RFCTL_EXTEN; 3110 ew32(RFCTL, rfctl); 3111 3112 /* 82571 and greater support packet-split where the protocol 3113 * header is placed in skb->data and the packet data is 3114 * placed in pages hanging off of skb_shinfo(skb)->nr_frags. 3115 * In the case of a non-split, skb->data is linearly filled, 3116 * followed by the page buffers. Therefore, skb->data is 3117 * sized to hold the largest protocol header. 3118 * 3119 * allocations using alloc_page take too long for regular MTU 3120 * so only enable packet split for jumbo frames 3121 * 3122 * Using pages when the page size is greater than 16k wastes 3123 * a lot of memory, since we allocate 3 pages at all times 3124 * per packet. 3125 */ 3126 pages = PAGE_USE_COUNT(adapter->netdev->mtu); 3127 if ((pages <= 3) && (PAGE_SIZE <= 16384) && (rctl & E1000_RCTL_LPE)) 3128 adapter->rx_ps_pages = pages; 3129 else 3130 adapter->rx_ps_pages = 0; 3131 3132 if (adapter->rx_ps_pages) { 3133 u32 psrctl = 0; 3134 3135 /* Enable Packet split descriptors */ 3136 rctl |= E1000_RCTL_DTYP_PS; 3137 3138 psrctl |= adapter->rx_ps_bsize0 >> E1000_PSRCTL_BSIZE0_SHIFT; 3139 3140 switch (adapter->rx_ps_pages) { 3141 case 3: 3142 psrctl |= PAGE_SIZE << E1000_PSRCTL_BSIZE3_SHIFT; 3143 /* fall-through */ 3144 case 2: 3145 psrctl |= PAGE_SIZE << E1000_PSRCTL_BSIZE2_SHIFT; 3146 /* fall-through */ 3147 case 1: 3148 psrctl |= PAGE_SIZE >> E1000_PSRCTL_BSIZE1_SHIFT; 3149 break; 3150 } 3151 3152 ew32(PSRCTL, psrctl); 3153 } 3154 3155 /* This is useful for sniffing bad packets. */ 3156 if (adapter->netdev->features & NETIF_F_RXALL) { 3157 /* UPE and MPE will be handled by normal PROMISC logic 3158 * in e1000e_set_rx_mode 3159 */ 3160 rctl |= (E1000_RCTL_SBP | /* Receive bad packets */ 3161 E1000_RCTL_BAM | /* RX All Bcast Pkts */ 3162 E1000_RCTL_PMCF); /* RX All MAC Ctrl Pkts */ 3163 3164 rctl &= ~(E1000_RCTL_VFE | /* Disable VLAN filter */ 3165 E1000_RCTL_DPF | /* Allow filtered pause */ 3166 E1000_RCTL_CFIEN); /* Dis VLAN CFIEN Filter */ 3167 /* Do not mess with E1000_CTRL_VME, it affects transmit as well, 3168 * and that breaks VLANs. 3169 */ 3170 } 3171 3172 ew32(RCTL, rctl); 3173 /* just started the receive unit, no need to restart */ 3174 adapter->flags &= ~FLAG_RESTART_NOW; 3175 } 3176 3177 /** 3178 * e1000_configure_rx - Configure Receive Unit after Reset 3179 * @adapter: board private structure 3180 * 3181 * Configure the Rx unit of the MAC after a reset. 3182 **/ 3183 static void e1000_configure_rx(struct e1000_adapter *adapter) 3184 { 3185 struct e1000_hw *hw = &adapter->hw; 3186 struct e1000_ring *rx_ring = adapter->rx_ring; 3187 u64 rdba; 3188 u32 rdlen, rctl, rxcsum, ctrl_ext; 3189 3190 if (adapter->rx_ps_pages) { 3191 /* this is a 32 byte descriptor */ 3192 rdlen = rx_ring->count * 3193 sizeof(union e1000_rx_desc_packet_split); 3194 adapter->clean_rx = e1000_clean_rx_irq_ps; 3195 adapter->alloc_rx_buf = e1000_alloc_rx_buffers_ps; 3196 } else if (adapter->netdev->mtu > ETH_FRAME_LEN + ETH_FCS_LEN) { 3197 rdlen = rx_ring->count * sizeof(union e1000_rx_desc_extended); 3198 adapter->clean_rx = e1000_clean_jumbo_rx_irq; 3199 adapter->alloc_rx_buf = e1000_alloc_jumbo_rx_buffers; 3200 } else { 3201 rdlen = rx_ring->count * sizeof(union e1000_rx_desc_extended); 3202 adapter->clean_rx = e1000_clean_rx_irq; 3203 adapter->alloc_rx_buf = e1000_alloc_rx_buffers; 3204 } 3205 3206 /* disable receives while setting up the descriptors */ 3207 rctl = er32(RCTL); 3208 if (!(adapter->flags2 & FLAG2_NO_DISABLE_RX)) 3209 ew32(RCTL, rctl & ~E1000_RCTL_EN); 3210 e1e_flush(); 3211 usleep_range(10000, 11000); 3212 3213 if (adapter->flags2 & FLAG2_DMA_BURST) { 3214 /* set the writeback threshold (only takes effect if the RDTR 3215 * is set). set GRAN=1 and write back up to 0x4 worth, and 3216 * enable prefetching of 0x20 Rx descriptors 3217 * granularity = 01 3218 * wthresh = 04, 3219 * hthresh = 04, 3220 * pthresh = 0x20 3221 */ 3222 ew32(RXDCTL(0), E1000_RXDCTL_DMA_BURST_ENABLE); 3223 ew32(RXDCTL(1), E1000_RXDCTL_DMA_BURST_ENABLE); 3224 } 3225 3226 /* set the Receive Delay Timer Register */ 3227 ew32(RDTR, adapter->rx_int_delay); 3228 3229 /* irq moderation */ 3230 ew32(RADV, adapter->rx_abs_int_delay); 3231 if ((adapter->itr_setting != 0) && (adapter->itr != 0)) 3232 e1000e_write_itr(adapter, adapter->itr); 3233 3234 ctrl_ext = er32(CTRL_EXT); 3235 /* Auto-Mask interrupts upon ICR access */ 3236 ctrl_ext |= E1000_CTRL_EXT_IAME; 3237 ew32(IAM, 0xffffffff); 3238 ew32(CTRL_EXT, ctrl_ext); 3239 e1e_flush(); 3240 3241 /* Setup the HW Rx Head and Tail Descriptor Pointers and 3242 * the Base and Length of the Rx Descriptor Ring 3243 */ 3244 rdba = rx_ring->dma; 3245 ew32(RDBAL(0), (rdba & DMA_BIT_MASK(32))); 3246 ew32(RDBAH(0), (rdba >> 32)); 3247 ew32(RDLEN(0), rdlen); 3248 ew32(RDH(0), 0); 3249 ew32(RDT(0), 0); 3250 rx_ring->head = adapter->hw.hw_addr + E1000_RDH(0); 3251 rx_ring->tail = adapter->hw.hw_addr + E1000_RDT(0); 3252 3253 writel(0, rx_ring->head); 3254 if (adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA) 3255 e1000e_update_rdt_wa(rx_ring, 0); 3256 else 3257 writel(0, rx_ring->tail); 3258 3259 /* Enable Receive Checksum Offload for TCP and UDP */ 3260 rxcsum = er32(RXCSUM); 3261 if (adapter->netdev->features & NETIF_F_RXCSUM) 3262 rxcsum |= E1000_RXCSUM_TUOFL; 3263 else 3264 rxcsum &= ~E1000_RXCSUM_TUOFL; 3265 ew32(RXCSUM, rxcsum); 3266 3267 /* With jumbo frames, excessive C-state transition latencies result 3268 * in dropped transactions. 3269 */ 3270 if (adapter->netdev->mtu > ETH_DATA_LEN) { 3271 u32 lat = 3272 ((er32(PBA) & E1000_PBA_RXA_MASK) * 1024 - 3273 adapter->max_frame_size) * 8 / 1000; 3274 3275 if (adapter->flags & FLAG_IS_ICH) { 3276 u32 rxdctl = er32(RXDCTL(0)); 3277 3278 ew32(RXDCTL(0), rxdctl | 0x3 | BIT(8)); 3279 } 3280 3281 dev_info(&adapter->pdev->dev, 3282 "Some CPU C-states have been disabled in order to enable jumbo frames\n"); 3283 cpu_latency_qos_update_request(&adapter->pm_qos_req, lat); 3284 } else { 3285 cpu_latency_qos_update_request(&adapter->pm_qos_req, 3286 PM_QOS_DEFAULT_VALUE); 3287 } 3288 3289 /* Enable Receives */ 3290 ew32(RCTL, rctl); 3291 } 3292 3293 /** 3294 * e1000e_write_mc_addr_list - write multicast addresses to MTA 3295 * @netdev: network interface device structure 3296 * 3297 * Writes multicast address list to the MTA hash table. 3298 * Returns: -ENOMEM on failure 3299 * 0 on no addresses written 3300 * X on writing X addresses to MTA 3301 */ 3302 static int e1000e_write_mc_addr_list(struct net_device *netdev) 3303 { 3304 struct e1000_adapter *adapter = netdev_priv(netdev); 3305 struct e1000_hw *hw = &adapter->hw; 3306 struct netdev_hw_addr *ha; 3307 u8 *mta_list; 3308 int i; 3309 3310 if (netdev_mc_empty(netdev)) { 3311 /* nothing to program, so clear mc list */ 3312 hw->mac.ops.update_mc_addr_list(hw, NULL, 0); 3313 return 0; 3314 } 3315 3316 mta_list = kcalloc(netdev_mc_count(netdev), ETH_ALEN, GFP_ATOMIC); 3317 if (!mta_list) 3318 return -ENOMEM; 3319 3320 /* update_mc_addr_list expects a packed array of only addresses. */ 3321 i = 0; 3322 netdev_for_each_mc_addr(ha, netdev) 3323 memcpy(mta_list + (i++ * ETH_ALEN), ha->addr, ETH_ALEN); 3324 3325 hw->mac.ops.update_mc_addr_list(hw, mta_list, i); 3326 kfree(mta_list); 3327 3328 return netdev_mc_count(netdev); 3329 } 3330 3331 /** 3332 * e1000e_write_uc_addr_list - write unicast addresses to RAR table 3333 * @netdev: network interface device structure 3334 * 3335 * Writes unicast address list to the RAR table. 3336 * Returns: -ENOMEM on failure/insufficient address space 3337 * 0 on no addresses written 3338 * X on writing X addresses to the RAR table 3339 **/ 3340 static int e1000e_write_uc_addr_list(struct net_device *netdev) 3341 { 3342 struct e1000_adapter *adapter = netdev_priv(netdev); 3343 struct e1000_hw *hw = &adapter->hw; 3344 unsigned int rar_entries; 3345 int count = 0; 3346 3347 rar_entries = hw->mac.ops.rar_get_count(hw); 3348 3349 /* save a rar entry for our hardware address */ 3350 rar_entries--; 3351 3352 /* save a rar entry for the LAA workaround */ 3353 if (adapter->flags & FLAG_RESET_OVERWRITES_LAA) 3354 rar_entries--; 3355 3356 /* return ENOMEM indicating insufficient memory for addresses */ 3357 if (netdev_uc_count(netdev) > rar_entries) 3358 return -ENOMEM; 3359 3360 if (!netdev_uc_empty(netdev) && rar_entries) { 3361 struct netdev_hw_addr *ha; 3362 3363 /* write the addresses in reverse order to avoid write 3364 * combining 3365 */ 3366 netdev_for_each_uc_addr(ha, netdev) { 3367 int ret_val; 3368 3369 if (!rar_entries) 3370 break; 3371 ret_val = hw->mac.ops.rar_set(hw, ha->addr, rar_entries--); 3372 if (ret_val < 0) 3373 return -ENOMEM; 3374 count++; 3375 } 3376 } 3377 3378 /* zero out the remaining RAR entries not used above */ 3379 for (; rar_entries > 0; rar_entries--) { 3380 ew32(RAH(rar_entries), 0); 3381 ew32(RAL(rar_entries), 0); 3382 } 3383 e1e_flush(); 3384 3385 return count; 3386 } 3387 3388 /** 3389 * e1000e_set_rx_mode - secondary unicast, Multicast and Promiscuous mode set 3390 * @netdev: network interface device structure 3391 * 3392 * The ndo_set_rx_mode entry point is called whenever the unicast or multicast 3393 * address list or the network interface flags are updated. This routine is 3394 * responsible for configuring the hardware for proper unicast, multicast, 3395 * promiscuous mode, and all-multi behavior. 3396 **/ 3397 static void e1000e_set_rx_mode(struct net_device *netdev) 3398 { 3399 struct e1000_adapter *adapter = netdev_priv(netdev); 3400 struct e1000_hw *hw = &adapter->hw; 3401 u32 rctl; 3402 3403 if (pm_runtime_suspended(netdev->dev.parent)) 3404 return; 3405 3406 /* Check for Promiscuous and All Multicast modes */ 3407 rctl = er32(RCTL); 3408 3409 /* clear the affected bits */ 3410 rctl &= ~(E1000_RCTL_UPE | E1000_RCTL_MPE); 3411 3412 if (netdev->flags & IFF_PROMISC) { 3413 rctl |= (E1000_RCTL_UPE | E1000_RCTL_MPE); 3414 /* Do not hardware filter VLANs in promisc mode */ 3415 e1000e_vlan_filter_disable(adapter); 3416 } else { 3417 int count; 3418 3419 if (netdev->flags & IFF_ALLMULTI) { 3420 rctl |= E1000_RCTL_MPE; 3421 } else { 3422 /* Write addresses to the MTA, if the attempt fails 3423 * then we should just turn on promiscuous mode so 3424 * that we can at least receive multicast traffic 3425 */ 3426 count = e1000e_write_mc_addr_list(netdev); 3427 if (count < 0) 3428 rctl |= E1000_RCTL_MPE; 3429 } 3430 e1000e_vlan_filter_enable(adapter); 3431 /* Write addresses to available RAR registers, if there is not 3432 * sufficient space to store all the addresses then enable 3433 * unicast promiscuous mode 3434 */ 3435 count = e1000e_write_uc_addr_list(netdev); 3436 if (count < 0) 3437 rctl |= E1000_RCTL_UPE; 3438 } 3439 3440 ew32(RCTL, rctl); 3441 3442 if (netdev->features & NETIF_F_HW_VLAN_CTAG_RX) 3443 e1000e_vlan_strip_enable(adapter); 3444 else 3445 e1000e_vlan_strip_disable(adapter); 3446 } 3447 3448 static void e1000e_setup_rss_hash(struct e1000_adapter *adapter) 3449 { 3450 struct e1000_hw *hw = &adapter->hw; 3451 u32 mrqc, rxcsum; 3452 u32 rss_key[10]; 3453 int i; 3454 3455 netdev_rss_key_fill(rss_key, sizeof(rss_key)); 3456 for (i = 0; i < 10; i++) 3457 ew32(RSSRK(i), rss_key[i]); 3458 3459 /* Direct all traffic to queue 0 */ 3460 for (i = 0; i < 32; i++) 3461 ew32(RETA(i), 0); 3462 3463 /* Disable raw packet checksumming so that RSS hash is placed in 3464 * descriptor on writeback. 3465 */ 3466 rxcsum = er32(RXCSUM); 3467 rxcsum |= E1000_RXCSUM_PCSD; 3468 3469 ew32(RXCSUM, rxcsum); 3470 3471 mrqc = (E1000_MRQC_RSS_FIELD_IPV4 | 3472 E1000_MRQC_RSS_FIELD_IPV4_TCP | 3473 E1000_MRQC_RSS_FIELD_IPV6 | 3474 E1000_MRQC_RSS_FIELD_IPV6_TCP | 3475 E1000_MRQC_RSS_FIELD_IPV6_TCP_EX); 3476 3477 ew32(MRQC, mrqc); 3478 } 3479 3480 /** 3481 * e1000e_get_base_timinca - get default SYSTIM time increment attributes 3482 * @adapter: board private structure 3483 * @timinca: pointer to returned time increment attributes 3484 * 3485 * Get attributes for incrementing the System Time Register SYSTIML/H at 3486 * the default base frequency, and set the cyclecounter shift value. 3487 **/ 3488 s32 e1000e_get_base_timinca(struct e1000_adapter *adapter, u32 *timinca) 3489 { 3490 struct e1000_hw *hw = &adapter->hw; 3491 u32 incvalue, incperiod, shift; 3492 3493 /* Make sure clock is enabled on I217/I218/I219 before checking 3494 * the frequency 3495 */ 3496 if ((hw->mac.type >= e1000_pch_lpt) && 3497 !(er32(TSYNCTXCTL) & E1000_TSYNCTXCTL_ENABLED) && 3498 !(er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_ENABLED)) { 3499 u32 fextnvm7 = er32(FEXTNVM7); 3500 3501 if (!(fextnvm7 & BIT(0))) { 3502 ew32(FEXTNVM7, fextnvm7 | BIT(0)); 3503 e1e_flush(); 3504 } 3505 } 3506 3507 switch (hw->mac.type) { 3508 case e1000_pch2lan: 3509 /* Stable 96MHz frequency */ 3510 incperiod = INCPERIOD_96MHZ; 3511 incvalue = INCVALUE_96MHZ; 3512 shift = INCVALUE_SHIFT_96MHZ; 3513 adapter->cc.shift = shift + INCPERIOD_SHIFT_96MHZ; 3514 break; 3515 case e1000_pch_lpt: 3516 if (er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_SYSCFI) { 3517 /* Stable 96MHz frequency */ 3518 incperiod = INCPERIOD_96MHZ; 3519 incvalue = INCVALUE_96MHZ; 3520 shift = INCVALUE_SHIFT_96MHZ; 3521 adapter->cc.shift = shift + INCPERIOD_SHIFT_96MHZ; 3522 } else { 3523 /* Stable 25MHz frequency */ 3524 incperiod = INCPERIOD_25MHZ; 3525 incvalue = INCVALUE_25MHZ; 3526 shift = INCVALUE_SHIFT_25MHZ; 3527 adapter->cc.shift = shift; 3528 } 3529 break; 3530 case e1000_pch_spt: 3531 /* Stable 24MHz frequency */ 3532 incperiod = INCPERIOD_24MHZ; 3533 incvalue = INCVALUE_24MHZ; 3534 shift = INCVALUE_SHIFT_24MHZ; 3535 adapter->cc.shift = shift; 3536 break; 3537 case e1000_pch_cnp: 3538 case e1000_pch_tgp: 3539 case e1000_pch_adp: 3540 if (er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_SYSCFI) { 3541 /* Stable 24MHz frequency */ 3542 incperiod = INCPERIOD_24MHZ; 3543 incvalue = INCVALUE_24MHZ; 3544 shift = INCVALUE_SHIFT_24MHZ; 3545 adapter->cc.shift = shift; 3546 } else { 3547 /* Stable 38400KHz frequency */ 3548 incperiod = INCPERIOD_38400KHZ; 3549 incvalue = INCVALUE_38400KHZ; 3550 shift = INCVALUE_SHIFT_38400KHZ; 3551 adapter->cc.shift = shift; 3552 } 3553 break; 3554 case e1000_82574: 3555 case e1000_82583: 3556 /* Stable 25MHz frequency */ 3557 incperiod = INCPERIOD_25MHZ; 3558 incvalue = INCVALUE_25MHZ; 3559 shift = INCVALUE_SHIFT_25MHZ; 3560 adapter->cc.shift = shift; 3561 break; 3562 default: 3563 return -EINVAL; 3564 } 3565 3566 *timinca = ((incperiod << E1000_TIMINCA_INCPERIOD_SHIFT) | 3567 ((incvalue << shift) & E1000_TIMINCA_INCVALUE_MASK)); 3568 3569 return 0; 3570 } 3571 3572 /** 3573 * e1000e_config_hwtstamp - configure the hwtstamp registers and enable/disable 3574 * @adapter: board private structure 3575 * 3576 * Outgoing time stamping can be enabled and disabled. Play nice and 3577 * disable it when requested, although it shouldn't cause any overhead 3578 * when no packet needs it. At most one packet in the queue may be 3579 * marked for time stamping, otherwise it would be impossible to tell 3580 * for sure to which packet the hardware time stamp belongs. 3581 * 3582 * Incoming time stamping has to be configured via the hardware filters. 3583 * Not all combinations are supported, in particular event type has to be 3584 * specified. Matching the kind of event packet is not supported, with the 3585 * exception of "all V2 events regardless of level 2 or 4". 3586 **/ 3587 static int e1000e_config_hwtstamp(struct e1000_adapter *adapter, 3588 struct hwtstamp_config *config) 3589 { 3590 struct e1000_hw *hw = &adapter->hw; 3591 u32 tsync_tx_ctl = E1000_TSYNCTXCTL_ENABLED; 3592 u32 tsync_rx_ctl = E1000_TSYNCRXCTL_ENABLED; 3593 u32 rxmtrl = 0; 3594 u16 rxudp = 0; 3595 bool is_l4 = false; 3596 bool is_l2 = false; 3597 u32 regval; 3598 3599 if (!(adapter->flags & FLAG_HAS_HW_TIMESTAMP)) 3600 return -EINVAL; 3601 3602 /* flags reserved for future extensions - must be zero */ 3603 if (config->flags) 3604 return -EINVAL; 3605 3606 switch (config->tx_type) { 3607 case HWTSTAMP_TX_OFF: 3608 tsync_tx_ctl = 0; 3609 break; 3610 case HWTSTAMP_TX_ON: 3611 break; 3612 default: 3613 return -ERANGE; 3614 } 3615 3616 switch (config->rx_filter) { 3617 case HWTSTAMP_FILTER_NONE: 3618 tsync_rx_ctl = 0; 3619 break; 3620 case HWTSTAMP_FILTER_PTP_V1_L4_SYNC: 3621 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L4_V1; 3622 rxmtrl = E1000_RXMTRL_PTP_V1_SYNC_MESSAGE; 3623 is_l4 = true; 3624 break; 3625 case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ: 3626 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L4_V1; 3627 rxmtrl = E1000_RXMTRL_PTP_V1_DELAY_REQ_MESSAGE; 3628 is_l4 = true; 3629 break; 3630 case HWTSTAMP_FILTER_PTP_V2_L2_SYNC: 3631 /* Also time stamps V2 L2 Path Delay Request/Response */ 3632 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L2_V2; 3633 rxmtrl = E1000_RXMTRL_PTP_V2_SYNC_MESSAGE; 3634 is_l2 = true; 3635 break; 3636 case HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ: 3637 /* Also time stamps V2 L2 Path Delay Request/Response. */ 3638 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L2_V2; 3639 rxmtrl = E1000_RXMTRL_PTP_V2_DELAY_REQ_MESSAGE; 3640 is_l2 = true; 3641 break; 3642 case HWTSTAMP_FILTER_PTP_V2_L4_SYNC: 3643 /* Hardware cannot filter just V2 L4 Sync messages; 3644 * fall-through to V2 (both L2 and L4) Sync. 3645 */ 3646 case HWTSTAMP_FILTER_PTP_V2_SYNC: 3647 /* Also time stamps V2 Path Delay Request/Response. */ 3648 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L2_L4_V2; 3649 rxmtrl = E1000_RXMTRL_PTP_V2_SYNC_MESSAGE; 3650 is_l2 = true; 3651 is_l4 = true; 3652 break; 3653 case HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ: 3654 /* Hardware cannot filter just V2 L4 Delay Request messages; 3655 * fall-through to V2 (both L2 and L4) Delay Request. 3656 */ 3657 case HWTSTAMP_FILTER_PTP_V2_DELAY_REQ: 3658 /* Also time stamps V2 Path Delay Request/Response. */ 3659 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L2_L4_V2; 3660 rxmtrl = E1000_RXMTRL_PTP_V2_DELAY_REQ_MESSAGE; 3661 is_l2 = true; 3662 is_l4 = true; 3663 break; 3664 case HWTSTAMP_FILTER_PTP_V2_L4_EVENT: 3665 case HWTSTAMP_FILTER_PTP_V2_L2_EVENT: 3666 /* Hardware cannot filter just V2 L4 or L2 Event messages; 3667 * fall-through to all V2 (both L2 and L4) Events. 3668 */ 3669 case HWTSTAMP_FILTER_PTP_V2_EVENT: 3670 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_EVENT_V2; 3671 config->rx_filter = HWTSTAMP_FILTER_PTP_V2_EVENT; 3672 is_l2 = true; 3673 is_l4 = true; 3674 break; 3675 case HWTSTAMP_FILTER_PTP_V1_L4_EVENT: 3676 /* For V1, the hardware can only filter Sync messages or 3677 * Delay Request messages but not both so fall-through to 3678 * time stamp all packets. 3679 */ 3680 case HWTSTAMP_FILTER_NTP_ALL: 3681 case HWTSTAMP_FILTER_ALL: 3682 is_l2 = true; 3683 is_l4 = true; 3684 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_ALL; 3685 config->rx_filter = HWTSTAMP_FILTER_ALL; 3686 break; 3687 default: 3688 return -ERANGE; 3689 } 3690 3691 adapter->hwtstamp_config = *config; 3692 3693 /* enable/disable Tx h/w time stamping */ 3694 regval = er32(TSYNCTXCTL); 3695 regval &= ~E1000_TSYNCTXCTL_ENABLED; 3696 regval |= tsync_tx_ctl; 3697 ew32(TSYNCTXCTL, regval); 3698 if ((er32(TSYNCTXCTL) & E1000_TSYNCTXCTL_ENABLED) != 3699 (regval & E1000_TSYNCTXCTL_ENABLED)) { 3700 e_err("Timesync Tx Control register not set as expected\n"); 3701 return -EAGAIN; 3702 } 3703 3704 /* enable/disable Rx h/w time stamping */ 3705 regval = er32(TSYNCRXCTL); 3706 regval &= ~(E1000_TSYNCRXCTL_ENABLED | E1000_TSYNCRXCTL_TYPE_MASK); 3707 regval |= tsync_rx_ctl; 3708 ew32(TSYNCRXCTL, regval); 3709 if ((er32(TSYNCRXCTL) & (E1000_TSYNCRXCTL_ENABLED | 3710 E1000_TSYNCRXCTL_TYPE_MASK)) != 3711 (regval & (E1000_TSYNCRXCTL_ENABLED | 3712 E1000_TSYNCRXCTL_TYPE_MASK))) { 3713 e_err("Timesync Rx Control register not set as expected\n"); 3714 return -EAGAIN; 3715 } 3716 3717 /* L2: define ethertype filter for time stamped packets */ 3718 if (is_l2) 3719 rxmtrl |= ETH_P_1588; 3720 3721 /* define which PTP packets get time stamped */ 3722 ew32(RXMTRL, rxmtrl); 3723 3724 /* Filter by destination port */ 3725 if (is_l4) { 3726 rxudp = PTP_EV_PORT; 3727 cpu_to_be16s(&rxudp); 3728 } 3729 ew32(RXUDP, rxudp); 3730 3731 e1e_flush(); 3732 3733 /* Clear TSYNCRXCTL_VALID & TSYNCTXCTL_VALID bit */ 3734 er32(RXSTMPH); 3735 er32(TXSTMPH); 3736 3737 return 0; 3738 } 3739 3740 /** 3741 * e1000_configure - configure the hardware for Rx and Tx 3742 * @adapter: private board structure 3743 **/ 3744 static void e1000_configure(struct e1000_adapter *adapter) 3745 { 3746 struct e1000_ring *rx_ring = adapter->rx_ring; 3747 3748 e1000e_set_rx_mode(adapter->netdev); 3749 3750 e1000_restore_vlan(adapter); 3751 e1000_init_manageability_pt(adapter); 3752 3753 e1000_configure_tx(adapter); 3754 3755 if (adapter->netdev->features & NETIF_F_RXHASH) 3756 e1000e_setup_rss_hash(adapter); 3757 e1000_setup_rctl(adapter); 3758 e1000_configure_rx(adapter); 3759 adapter->alloc_rx_buf(rx_ring, e1000_desc_unused(rx_ring), GFP_KERNEL); 3760 } 3761 3762 /** 3763 * e1000e_power_up_phy - restore link in case the phy was powered down 3764 * @adapter: address of board private structure 3765 * 3766 * The phy may be powered down to save power and turn off link when the 3767 * driver is unloaded and wake on lan is not enabled (among others) 3768 * *** this routine MUST be followed by a call to e1000e_reset *** 3769 **/ 3770 void e1000e_power_up_phy(struct e1000_adapter *adapter) 3771 { 3772 if (adapter->hw.phy.ops.power_up) 3773 adapter->hw.phy.ops.power_up(&adapter->hw); 3774 3775 adapter->hw.mac.ops.setup_link(&adapter->hw); 3776 } 3777 3778 /** 3779 * e1000_power_down_phy - Power down the PHY 3780 * 3781 * Power down the PHY so no link is implied when interface is down. 3782 * The PHY cannot be powered down if management or WoL is active. 3783 */ 3784 static void e1000_power_down_phy(struct e1000_adapter *adapter) 3785 { 3786 if (adapter->hw.phy.ops.power_down) 3787 adapter->hw.phy.ops.power_down(&adapter->hw); 3788 } 3789 3790 /** 3791 * e1000_flush_tx_ring - remove all descriptors from the tx_ring 3792 * 3793 * We want to clear all pending descriptors from the TX ring. 3794 * zeroing happens when the HW reads the regs. We assign the ring itself as 3795 * the data of the next descriptor. We don't care about the data we are about 3796 * to reset the HW. 3797 */ 3798 static void e1000_flush_tx_ring(struct e1000_adapter *adapter) 3799 { 3800 struct e1000_hw *hw = &adapter->hw; 3801 struct e1000_ring *tx_ring = adapter->tx_ring; 3802 struct e1000_tx_desc *tx_desc = NULL; 3803 u32 tdt, tctl, txd_lower = E1000_TXD_CMD_IFCS; 3804 u16 size = 512; 3805 3806 tctl = er32(TCTL); 3807 ew32(TCTL, tctl | E1000_TCTL_EN); 3808 tdt = er32(TDT(0)); 3809 BUG_ON(tdt != tx_ring->next_to_use); 3810 tx_desc = E1000_TX_DESC(*tx_ring, tx_ring->next_to_use); 3811 tx_desc->buffer_addr = cpu_to_le64(tx_ring->dma); 3812 3813 tx_desc->lower.data = cpu_to_le32(txd_lower | size); 3814 tx_desc->upper.data = 0; 3815 /* flush descriptors to memory before notifying the HW */ 3816 wmb(); 3817 tx_ring->next_to_use++; 3818 if (tx_ring->next_to_use == tx_ring->count) 3819 tx_ring->next_to_use = 0; 3820 ew32(TDT(0), tx_ring->next_to_use); 3821 usleep_range(200, 250); 3822 } 3823 3824 /** 3825 * e1000_flush_rx_ring - remove all descriptors from the rx_ring 3826 * 3827 * Mark all descriptors in the RX ring as consumed and disable the rx ring 3828 */ 3829 static void e1000_flush_rx_ring(struct e1000_adapter *adapter) 3830 { 3831 u32 rctl, rxdctl; 3832 struct e1000_hw *hw = &adapter->hw; 3833 3834 rctl = er32(RCTL); 3835 ew32(RCTL, rctl & ~E1000_RCTL_EN); 3836 e1e_flush(); 3837 usleep_range(100, 150); 3838 3839 rxdctl = er32(RXDCTL(0)); 3840 /* zero the lower 14 bits (prefetch and host thresholds) */ 3841 rxdctl &= 0xffffc000; 3842 3843 /* update thresholds: prefetch threshold to 31, host threshold to 1 3844 * and make sure the granularity is "descriptors" and not "cache lines" 3845 */ 3846 rxdctl |= (0x1F | BIT(8) | E1000_RXDCTL_THRESH_UNIT_DESC); 3847 3848 ew32(RXDCTL(0), rxdctl); 3849 /* momentarily enable the RX ring for the changes to take effect */ 3850 ew32(RCTL, rctl | E1000_RCTL_EN); 3851 e1e_flush(); 3852 usleep_range(100, 150); 3853 ew32(RCTL, rctl & ~E1000_RCTL_EN); 3854 } 3855 3856 /** 3857 * e1000_flush_desc_rings - remove all descriptors from the descriptor rings 3858 * 3859 * In i219, the descriptor rings must be emptied before resetting the HW 3860 * or before changing the device state to D3 during runtime (runtime PM). 3861 * 3862 * Failure to do this will cause the HW to enter a unit hang state which can 3863 * only be released by PCI reset on the device 3864 * 3865 */ 3866 3867 static void e1000_flush_desc_rings(struct e1000_adapter *adapter) 3868 { 3869 u16 hang_state; 3870 u32 fext_nvm11, tdlen; 3871 struct e1000_hw *hw = &adapter->hw; 3872 3873 /* First, disable MULR fix in FEXTNVM11 */ 3874 fext_nvm11 = er32(FEXTNVM11); 3875 fext_nvm11 |= E1000_FEXTNVM11_DISABLE_MULR_FIX; 3876 ew32(FEXTNVM11, fext_nvm11); 3877 /* do nothing if we're not in faulty state, or if the queue is empty */ 3878 tdlen = er32(TDLEN(0)); 3879 pci_read_config_word(adapter->pdev, PCICFG_DESC_RING_STATUS, 3880 &hang_state); 3881 if (!(hang_state & FLUSH_DESC_REQUIRED) || !tdlen) 3882 return; 3883 e1000_flush_tx_ring(adapter); 3884 /* recheck, maybe the fault is caused by the rx ring */ 3885 pci_read_config_word(adapter->pdev, PCICFG_DESC_RING_STATUS, 3886 &hang_state); 3887 if (hang_state & FLUSH_DESC_REQUIRED) 3888 e1000_flush_rx_ring(adapter); 3889 } 3890 3891 /** 3892 * e1000e_systim_reset - reset the timesync registers after a hardware reset 3893 * @adapter: board private structure 3894 * 3895 * When the MAC is reset, all hardware bits for timesync will be reset to the 3896 * default values. This function will restore the settings last in place. 3897 * Since the clock SYSTIME registers are reset, we will simply restore the 3898 * cyclecounter to the kernel real clock time. 3899 **/ 3900 static void e1000e_systim_reset(struct e1000_adapter *adapter) 3901 { 3902 struct ptp_clock_info *info = &adapter->ptp_clock_info; 3903 struct e1000_hw *hw = &adapter->hw; 3904 unsigned long flags; 3905 u32 timinca; 3906 s32 ret_val; 3907 3908 if (!(adapter->flags & FLAG_HAS_HW_TIMESTAMP)) 3909 return; 3910 3911 if (info->adjfreq) { 3912 /* restore the previous ptp frequency delta */ 3913 ret_val = info->adjfreq(info, adapter->ptp_delta); 3914 } else { 3915 /* set the default base frequency if no adjustment possible */ 3916 ret_val = e1000e_get_base_timinca(adapter, &timinca); 3917 if (!ret_val) 3918 ew32(TIMINCA, timinca); 3919 } 3920 3921 if (ret_val) { 3922 dev_warn(&adapter->pdev->dev, 3923 "Failed to restore TIMINCA clock rate delta: %d\n", 3924 ret_val); 3925 return; 3926 } 3927 3928 /* reset the systim ns time counter */ 3929 spin_lock_irqsave(&adapter->systim_lock, flags); 3930 timecounter_init(&adapter->tc, &adapter->cc, 3931 ktime_to_ns(ktime_get_real())); 3932 spin_unlock_irqrestore(&adapter->systim_lock, flags); 3933 3934 /* restore the previous hwtstamp configuration settings */ 3935 e1000e_config_hwtstamp(adapter, &adapter->hwtstamp_config); 3936 } 3937 3938 /** 3939 * e1000e_reset - bring the hardware into a known good state 3940 * 3941 * This function boots the hardware and enables some settings that 3942 * require a configuration cycle of the hardware - those cannot be 3943 * set/changed during runtime. After reset the device needs to be 3944 * properly configured for Rx, Tx etc. 3945 */ 3946 void e1000e_reset(struct e1000_adapter *adapter) 3947 { 3948 struct e1000_mac_info *mac = &adapter->hw.mac; 3949 struct e1000_fc_info *fc = &adapter->hw.fc; 3950 struct e1000_hw *hw = &adapter->hw; 3951 u32 tx_space, min_tx_space, min_rx_space; 3952 u32 pba = adapter->pba; 3953 u16 hwm; 3954 3955 /* reset Packet Buffer Allocation to default */ 3956 ew32(PBA, pba); 3957 3958 if (adapter->max_frame_size > (VLAN_ETH_FRAME_LEN + ETH_FCS_LEN)) { 3959 /* To maintain wire speed transmits, the Tx FIFO should be 3960 * large enough to accommodate two full transmit packets, 3961 * rounded up to the next 1KB and expressed in KB. Likewise, 3962 * the Rx FIFO should be large enough to accommodate at least 3963 * one full receive packet and is similarly rounded up and 3964 * expressed in KB. 3965 */ 3966 pba = er32(PBA); 3967 /* upper 16 bits has Tx packet buffer allocation size in KB */ 3968 tx_space = pba >> 16; 3969 /* lower 16 bits has Rx packet buffer allocation size in KB */ 3970 pba &= 0xffff; 3971 /* the Tx fifo also stores 16 bytes of information about the Tx 3972 * but don't include ethernet FCS because hardware appends it 3973 */ 3974 min_tx_space = (adapter->max_frame_size + 3975 sizeof(struct e1000_tx_desc) - ETH_FCS_LEN) * 2; 3976 min_tx_space = ALIGN(min_tx_space, 1024); 3977 min_tx_space >>= 10; 3978 /* software strips receive CRC, so leave room for it */ 3979 min_rx_space = adapter->max_frame_size; 3980 min_rx_space = ALIGN(min_rx_space, 1024); 3981 min_rx_space >>= 10; 3982 3983 /* If current Tx allocation is less than the min Tx FIFO size, 3984 * and the min Tx FIFO size is less than the current Rx FIFO 3985 * allocation, take space away from current Rx allocation 3986 */ 3987 if ((tx_space < min_tx_space) && 3988 ((min_tx_space - tx_space) < pba)) { 3989 pba -= min_tx_space - tx_space; 3990 3991 /* if short on Rx space, Rx wins and must trump Tx 3992 * adjustment 3993 */ 3994 if (pba < min_rx_space) 3995 pba = min_rx_space; 3996 } 3997 3998 ew32(PBA, pba); 3999 } 4000 4001 /* flow control settings 4002 * 4003 * The high water mark must be low enough to fit one full frame 4004 * (or the size used for early receive) above it in the Rx FIFO. 4005 * Set it to the lower of: 4006 * - 90% of the Rx FIFO size, and 4007 * - the full Rx FIFO size minus one full frame 4008 */ 4009 if (adapter->flags & FLAG_DISABLE_FC_PAUSE_TIME) 4010 fc->pause_time = 0xFFFF; 4011 else 4012 fc->pause_time = E1000_FC_PAUSE_TIME; 4013 fc->send_xon = true; 4014 fc->current_mode = fc->requested_mode; 4015 4016 switch (hw->mac.type) { 4017 case e1000_ich9lan: 4018 case e1000_ich10lan: 4019 if (adapter->netdev->mtu > ETH_DATA_LEN) { 4020 pba = 14; 4021 ew32(PBA, pba); 4022 fc->high_water = 0x2800; 4023 fc->low_water = fc->high_water - 8; 4024 break; 4025 } 4026 /* fall-through */ 4027 default: 4028 hwm = min(((pba << 10) * 9 / 10), 4029 ((pba << 10) - adapter->max_frame_size)); 4030 4031 fc->high_water = hwm & E1000_FCRTH_RTH; /* 8-byte granularity */ 4032 fc->low_water = fc->high_water - 8; 4033 break; 4034 case e1000_pchlan: 4035 /* Workaround PCH LOM adapter hangs with certain network 4036 * loads. If hangs persist, try disabling Tx flow control. 4037 */ 4038 if (adapter->netdev->mtu > ETH_DATA_LEN) { 4039 fc->high_water = 0x3500; 4040 fc->low_water = 0x1500; 4041 } else { 4042 fc->high_water = 0x5000; 4043 fc->low_water = 0x3000; 4044 } 4045 fc->refresh_time = 0x1000; 4046 break; 4047 case e1000_pch2lan: 4048 case e1000_pch_lpt: 4049 case e1000_pch_spt: 4050 case e1000_pch_cnp: 4051 /* fall-through */ 4052 case e1000_pch_tgp: 4053 case e1000_pch_adp: 4054 fc->refresh_time = 0xFFFF; 4055 fc->pause_time = 0xFFFF; 4056 4057 if (adapter->netdev->mtu <= ETH_DATA_LEN) { 4058 fc->high_water = 0x05C20; 4059 fc->low_water = 0x05048; 4060 break; 4061 } 4062 4063 pba = 14; 4064 ew32(PBA, pba); 4065 fc->high_water = ((pba << 10) * 9 / 10) & E1000_FCRTH_RTH; 4066 fc->low_water = ((pba << 10) * 8 / 10) & E1000_FCRTL_RTL; 4067 break; 4068 } 4069 4070 /* Alignment of Tx data is on an arbitrary byte boundary with the 4071 * maximum size per Tx descriptor limited only to the transmit 4072 * allocation of the packet buffer minus 96 bytes with an upper 4073 * limit of 24KB due to receive synchronization limitations. 4074 */ 4075 adapter->tx_fifo_limit = min_t(u32, ((er32(PBA) >> 16) << 10) - 96, 4076 24 << 10); 4077 4078 /* Disable Adaptive Interrupt Moderation if 2 full packets cannot 4079 * fit in receive buffer. 4080 */ 4081 if (adapter->itr_setting & 0x3) { 4082 if ((adapter->max_frame_size * 2) > (pba << 10)) { 4083 if (!(adapter->flags2 & FLAG2_DISABLE_AIM)) { 4084 dev_info(&adapter->pdev->dev, 4085 "Interrupt Throttle Rate off\n"); 4086 adapter->flags2 |= FLAG2_DISABLE_AIM; 4087 e1000e_write_itr(adapter, 0); 4088 } 4089 } else if (adapter->flags2 & FLAG2_DISABLE_AIM) { 4090 dev_info(&adapter->pdev->dev, 4091 "Interrupt Throttle Rate on\n"); 4092 adapter->flags2 &= ~FLAG2_DISABLE_AIM; 4093 adapter->itr = 20000; 4094 e1000e_write_itr(adapter, adapter->itr); 4095 } 4096 } 4097 4098 if (hw->mac.type >= e1000_pch_spt) 4099 e1000_flush_desc_rings(adapter); 4100 /* Allow time for pending master requests to run */ 4101 mac->ops.reset_hw(hw); 4102 4103 /* For parts with AMT enabled, let the firmware know 4104 * that the network interface is in control 4105 */ 4106 if (adapter->flags & FLAG_HAS_AMT) 4107 e1000e_get_hw_control(adapter); 4108 4109 ew32(WUC, 0); 4110 4111 if (mac->ops.init_hw(hw)) 4112 e_err("Hardware Error\n"); 4113 4114 e1000_update_mng_vlan(adapter); 4115 4116 /* Enable h/w to recognize an 802.1Q VLAN Ethernet packet */ 4117 ew32(VET, ETH_P_8021Q); 4118 4119 e1000e_reset_adaptive(hw); 4120 4121 /* restore systim and hwtstamp settings */ 4122 e1000e_systim_reset(adapter); 4123 4124 /* Set EEE advertisement as appropriate */ 4125 if (adapter->flags2 & FLAG2_HAS_EEE) { 4126 s32 ret_val; 4127 u16 adv_addr; 4128 4129 switch (hw->phy.type) { 4130 case e1000_phy_82579: 4131 adv_addr = I82579_EEE_ADVERTISEMENT; 4132 break; 4133 case e1000_phy_i217: 4134 adv_addr = I217_EEE_ADVERTISEMENT; 4135 break; 4136 default: 4137 dev_err(&adapter->pdev->dev, 4138 "Invalid PHY type setting EEE advertisement\n"); 4139 return; 4140 } 4141 4142 ret_val = hw->phy.ops.acquire(hw); 4143 if (ret_val) { 4144 dev_err(&adapter->pdev->dev, 4145 "EEE advertisement - unable to acquire PHY\n"); 4146 return; 4147 } 4148 4149 e1000_write_emi_reg_locked(hw, adv_addr, 4150 hw->dev_spec.ich8lan.eee_disable ? 4151 0 : adapter->eee_advert); 4152 4153 hw->phy.ops.release(hw); 4154 } 4155 4156 if (!netif_running(adapter->netdev) && 4157 !test_bit(__E1000_TESTING, &adapter->state)) 4158 e1000_power_down_phy(adapter); 4159 4160 e1000_get_phy_info(hw); 4161 4162 if ((adapter->flags & FLAG_HAS_SMART_POWER_DOWN) && 4163 !(adapter->flags & FLAG_SMART_POWER_DOWN)) { 4164 u16 phy_data = 0; 4165 /* speed up time to link by disabling smart power down, ignore 4166 * the return value of this function because there is nothing 4167 * different we would do if it failed 4168 */ 4169 e1e_rphy(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data); 4170 phy_data &= ~IGP02E1000_PM_SPD; 4171 e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT, phy_data); 4172 } 4173 if (hw->mac.type >= e1000_pch_spt && adapter->int_mode == 0) { 4174 u32 reg; 4175 4176 /* Fextnvm7 @ 0xe4[2] = 1 */ 4177 reg = er32(FEXTNVM7); 4178 reg |= E1000_FEXTNVM7_SIDE_CLK_UNGATE; 4179 ew32(FEXTNVM7, reg); 4180 /* Fextnvm9 @ 0x5bb4[13:12] = 11 */ 4181 reg = er32(FEXTNVM9); 4182 reg |= E1000_FEXTNVM9_IOSFSB_CLKGATE_DIS | 4183 E1000_FEXTNVM9_IOSFSB_CLKREQ_DIS; 4184 ew32(FEXTNVM9, reg); 4185 } 4186 4187 } 4188 4189 /** 4190 * e1000e_trigger_lsc - trigger an LSC interrupt 4191 * @adapter: 4192 * 4193 * Fire a link status change interrupt to start the watchdog. 4194 **/ 4195 static void e1000e_trigger_lsc(struct e1000_adapter *adapter) 4196 { 4197 struct e1000_hw *hw = &adapter->hw; 4198 4199 if (adapter->msix_entries) 4200 ew32(ICS, E1000_ICS_LSC | E1000_ICS_OTHER); 4201 else 4202 ew32(ICS, E1000_ICS_LSC); 4203 } 4204 4205 void e1000e_up(struct e1000_adapter *adapter) 4206 { 4207 /* hardware has been reset, we need to reload some things */ 4208 e1000_configure(adapter); 4209 4210 clear_bit(__E1000_DOWN, &adapter->state); 4211 4212 if (adapter->msix_entries) 4213 e1000_configure_msix(adapter); 4214 e1000_irq_enable(adapter); 4215 4216 /* Tx queue started by watchdog timer when link is up */ 4217 4218 e1000e_trigger_lsc(adapter); 4219 } 4220 4221 static void e1000e_flush_descriptors(struct e1000_adapter *adapter) 4222 { 4223 struct e1000_hw *hw = &adapter->hw; 4224 4225 if (!(adapter->flags2 & FLAG2_DMA_BURST)) 4226 return; 4227 4228 /* flush pending descriptor writebacks to memory */ 4229 ew32(TIDV, adapter->tx_int_delay | E1000_TIDV_FPD); 4230 ew32(RDTR, adapter->rx_int_delay | E1000_RDTR_FPD); 4231 4232 /* execute the writes immediately */ 4233 e1e_flush(); 4234 4235 /* due to rare timing issues, write to TIDV/RDTR again to ensure the 4236 * write is successful 4237 */ 4238 ew32(TIDV, adapter->tx_int_delay | E1000_TIDV_FPD); 4239 ew32(RDTR, adapter->rx_int_delay | E1000_RDTR_FPD); 4240 4241 /* execute the writes immediately */ 4242 e1e_flush(); 4243 } 4244 4245 static void e1000e_update_stats(struct e1000_adapter *adapter); 4246 4247 /** 4248 * e1000e_down - quiesce the device and optionally reset the hardware 4249 * @adapter: board private structure 4250 * @reset: boolean flag to reset the hardware or not 4251 */ 4252 void e1000e_down(struct e1000_adapter *adapter, bool reset) 4253 { 4254 struct net_device *netdev = adapter->netdev; 4255 struct e1000_hw *hw = &adapter->hw; 4256 u32 tctl, rctl; 4257 4258 /* signal that we're down so the interrupt handler does not 4259 * reschedule our watchdog timer 4260 */ 4261 set_bit(__E1000_DOWN, &adapter->state); 4262 4263 netif_carrier_off(netdev); 4264 4265 /* disable receives in the hardware */ 4266 rctl = er32(RCTL); 4267 if (!(adapter->flags2 & FLAG2_NO_DISABLE_RX)) 4268 ew32(RCTL, rctl & ~E1000_RCTL_EN); 4269 /* flush and sleep below */ 4270 4271 netif_stop_queue(netdev); 4272 4273 /* disable transmits in the hardware */ 4274 tctl = er32(TCTL); 4275 tctl &= ~E1000_TCTL_EN; 4276 ew32(TCTL, tctl); 4277 4278 /* flush both disables and wait for them to finish */ 4279 e1e_flush(); 4280 usleep_range(10000, 11000); 4281 4282 e1000_irq_disable(adapter); 4283 4284 napi_synchronize(&adapter->napi); 4285 4286 del_timer_sync(&adapter->watchdog_timer); 4287 del_timer_sync(&adapter->phy_info_timer); 4288 4289 spin_lock(&adapter->stats64_lock); 4290 e1000e_update_stats(adapter); 4291 spin_unlock(&adapter->stats64_lock); 4292 4293 e1000e_flush_descriptors(adapter); 4294 4295 adapter->link_speed = 0; 4296 adapter->link_duplex = 0; 4297 4298 /* Disable Si errata workaround on PCHx for jumbo frame flow */ 4299 if ((hw->mac.type >= e1000_pch2lan) && 4300 (adapter->netdev->mtu > ETH_DATA_LEN) && 4301 e1000_lv_jumbo_workaround_ich8lan(hw, false)) 4302 e_dbg("failed to disable jumbo frame workaround mode\n"); 4303 4304 if (!pci_channel_offline(adapter->pdev)) { 4305 if (reset) 4306 e1000e_reset(adapter); 4307 else if (hw->mac.type >= e1000_pch_spt) 4308 e1000_flush_desc_rings(adapter); 4309 } 4310 e1000_clean_tx_ring(adapter->tx_ring); 4311 e1000_clean_rx_ring(adapter->rx_ring); 4312 } 4313 4314 void e1000e_reinit_locked(struct e1000_adapter *adapter) 4315 { 4316 might_sleep(); 4317 while (test_and_set_bit(__E1000_RESETTING, &adapter->state)) 4318 usleep_range(1000, 1100); 4319 e1000e_down(adapter, true); 4320 e1000e_up(adapter); 4321 clear_bit(__E1000_RESETTING, &adapter->state); 4322 } 4323 4324 /** 4325 * e1000e_sanitize_systim - sanitize raw cycle counter reads 4326 * @hw: pointer to the HW structure 4327 * @systim: PHC time value read, sanitized and returned 4328 * @sts: structure to hold system time before and after reading SYSTIML, 4329 * may be NULL 4330 * 4331 * Errata for 82574/82583 possible bad bits read from SYSTIMH/L: 4332 * check to see that the time is incrementing at a reasonable 4333 * rate and is a multiple of incvalue. 4334 **/ 4335 static u64 e1000e_sanitize_systim(struct e1000_hw *hw, u64 systim, 4336 struct ptp_system_timestamp *sts) 4337 { 4338 u64 time_delta, rem, temp; 4339 u64 systim_next; 4340 u32 incvalue; 4341 int i; 4342 4343 incvalue = er32(TIMINCA) & E1000_TIMINCA_INCVALUE_MASK; 4344 for (i = 0; i < E1000_MAX_82574_SYSTIM_REREADS; i++) { 4345 /* latch SYSTIMH on read of SYSTIML */ 4346 ptp_read_system_prets(sts); 4347 systim_next = (u64)er32(SYSTIML); 4348 ptp_read_system_postts(sts); 4349 systim_next |= (u64)er32(SYSTIMH) << 32; 4350 4351 time_delta = systim_next - systim; 4352 temp = time_delta; 4353 /* VMWare users have seen incvalue of zero, don't div / 0 */ 4354 rem = incvalue ? do_div(temp, incvalue) : (time_delta != 0); 4355 4356 systim = systim_next; 4357 4358 if ((time_delta < E1000_82574_SYSTIM_EPSILON) && (rem == 0)) 4359 break; 4360 } 4361 4362 return systim; 4363 } 4364 4365 /** 4366 * e1000e_read_systim - read SYSTIM register 4367 * @adapter: board private structure 4368 * @sts: structure which will contain system time before and after reading 4369 * SYSTIML, may be NULL 4370 **/ 4371 u64 e1000e_read_systim(struct e1000_adapter *adapter, 4372 struct ptp_system_timestamp *sts) 4373 { 4374 struct e1000_hw *hw = &adapter->hw; 4375 u32 systimel, systimel_2, systimeh; 4376 u64 systim; 4377 /* SYSTIMH latching upon SYSTIML read does not work well. 4378 * This means that if SYSTIML overflows after we read it but before 4379 * we read SYSTIMH, the value of SYSTIMH has been incremented and we 4380 * will experience a huge non linear increment in the systime value 4381 * to fix that we test for overflow and if true, we re-read systime. 4382 */ 4383 ptp_read_system_prets(sts); 4384 systimel = er32(SYSTIML); 4385 ptp_read_system_postts(sts); 4386 systimeh = er32(SYSTIMH); 4387 /* Is systimel is so large that overflow is possible? */ 4388 if (systimel >= (u32)0xffffffff - E1000_TIMINCA_INCVALUE_MASK) { 4389 ptp_read_system_prets(sts); 4390 systimel_2 = er32(SYSTIML); 4391 ptp_read_system_postts(sts); 4392 if (systimel > systimel_2) { 4393 /* There was an overflow, read again SYSTIMH, and use 4394 * systimel_2 4395 */ 4396 systimeh = er32(SYSTIMH); 4397 systimel = systimel_2; 4398 } 4399 } 4400 systim = (u64)systimel; 4401 systim |= (u64)systimeh << 32; 4402 4403 if (adapter->flags2 & FLAG2_CHECK_SYSTIM_OVERFLOW) 4404 systim = e1000e_sanitize_systim(hw, systim, sts); 4405 4406 return systim; 4407 } 4408 4409 /** 4410 * e1000e_cyclecounter_read - read raw cycle counter (used by time counter) 4411 * @cc: cyclecounter structure 4412 **/ 4413 static u64 e1000e_cyclecounter_read(const struct cyclecounter *cc) 4414 { 4415 struct e1000_adapter *adapter = container_of(cc, struct e1000_adapter, 4416 cc); 4417 4418 return e1000e_read_systim(adapter, NULL); 4419 } 4420 4421 /** 4422 * e1000_sw_init - Initialize general software structures (struct e1000_adapter) 4423 * @adapter: board private structure to initialize 4424 * 4425 * e1000_sw_init initializes the Adapter private data structure. 4426 * Fields are initialized based on PCI device information and 4427 * OS network device settings (MTU size). 4428 **/ 4429 static int e1000_sw_init(struct e1000_adapter *adapter) 4430 { 4431 struct net_device *netdev = adapter->netdev; 4432 4433 adapter->rx_buffer_len = VLAN_ETH_FRAME_LEN + ETH_FCS_LEN; 4434 adapter->rx_ps_bsize0 = 128; 4435 adapter->max_frame_size = netdev->mtu + VLAN_ETH_HLEN + ETH_FCS_LEN; 4436 adapter->min_frame_size = ETH_ZLEN + ETH_FCS_LEN; 4437 adapter->tx_ring_count = E1000_DEFAULT_TXD; 4438 adapter->rx_ring_count = E1000_DEFAULT_RXD; 4439 4440 spin_lock_init(&adapter->stats64_lock); 4441 4442 e1000e_set_interrupt_capability(adapter); 4443 4444 if (e1000_alloc_queues(adapter)) 4445 return -ENOMEM; 4446 4447 /* Setup hardware time stamping cyclecounter */ 4448 if (adapter->flags & FLAG_HAS_HW_TIMESTAMP) { 4449 adapter->cc.read = e1000e_cyclecounter_read; 4450 adapter->cc.mask = CYCLECOUNTER_MASK(64); 4451 adapter->cc.mult = 1; 4452 /* cc.shift set in e1000e_get_base_tininca() */ 4453 4454 spin_lock_init(&adapter->systim_lock); 4455 INIT_WORK(&adapter->tx_hwtstamp_work, e1000e_tx_hwtstamp_work); 4456 } 4457 4458 /* Explicitly disable IRQ since the NIC can be in any state. */ 4459 e1000_irq_disable(adapter); 4460 4461 set_bit(__E1000_DOWN, &adapter->state); 4462 return 0; 4463 } 4464 4465 /** 4466 * e1000_intr_msi_test - Interrupt Handler 4467 * @irq: interrupt number 4468 * @data: pointer to a network interface device structure 4469 **/ 4470 static irqreturn_t e1000_intr_msi_test(int __always_unused irq, void *data) 4471 { 4472 struct net_device *netdev = data; 4473 struct e1000_adapter *adapter = netdev_priv(netdev); 4474 struct e1000_hw *hw = &adapter->hw; 4475 u32 icr = er32(ICR); 4476 4477 e_dbg("icr is %08X\n", icr); 4478 if (icr & E1000_ICR_RXSEQ) { 4479 adapter->flags &= ~FLAG_MSI_TEST_FAILED; 4480 /* Force memory writes to complete before acknowledging the 4481 * interrupt is handled. 4482 */ 4483 wmb(); 4484 } 4485 4486 return IRQ_HANDLED; 4487 } 4488 4489 /** 4490 * e1000_test_msi_interrupt - Returns 0 for successful test 4491 * @adapter: board private struct 4492 * 4493 * code flow taken from tg3.c 4494 **/ 4495 static int e1000_test_msi_interrupt(struct e1000_adapter *adapter) 4496 { 4497 struct net_device *netdev = adapter->netdev; 4498 struct e1000_hw *hw = &adapter->hw; 4499 int err; 4500 4501 /* poll_enable hasn't been called yet, so don't need disable */ 4502 /* clear any pending events */ 4503 er32(ICR); 4504 4505 /* free the real vector and request a test handler */ 4506 e1000_free_irq(adapter); 4507 e1000e_reset_interrupt_capability(adapter); 4508 4509 /* Assume that the test fails, if it succeeds then the test 4510 * MSI irq handler will unset this flag 4511 */ 4512 adapter->flags |= FLAG_MSI_TEST_FAILED; 4513 4514 err = pci_enable_msi(adapter->pdev); 4515 if (err) 4516 goto msi_test_failed; 4517 4518 err = request_irq(adapter->pdev->irq, e1000_intr_msi_test, 0, 4519 netdev->name, netdev); 4520 if (err) { 4521 pci_disable_msi(adapter->pdev); 4522 goto msi_test_failed; 4523 } 4524 4525 /* Force memory writes to complete before enabling and firing an 4526 * interrupt. 4527 */ 4528 wmb(); 4529 4530 e1000_irq_enable(adapter); 4531 4532 /* fire an unusual interrupt on the test handler */ 4533 ew32(ICS, E1000_ICS_RXSEQ); 4534 e1e_flush(); 4535 msleep(100); 4536 4537 e1000_irq_disable(adapter); 4538 4539 rmb(); /* read flags after interrupt has been fired */ 4540 4541 if (adapter->flags & FLAG_MSI_TEST_FAILED) { 4542 adapter->int_mode = E1000E_INT_MODE_LEGACY; 4543 e_info("MSI interrupt test failed, using legacy interrupt.\n"); 4544 } else { 4545 e_dbg("MSI interrupt test succeeded!\n"); 4546 } 4547 4548 free_irq(adapter->pdev->irq, netdev); 4549 pci_disable_msi(adapter->pdev); 4550 4551 msi_test_failed: 4552 e1000e_set_interrupt_capability(adapter); 4553 return e1000_request_irq(adapter); 4554 } 4555 4556 /** 4557 * e1000_test_msi - Returns 0 if MSI test succeeds or INTx mode is restored 4558 * @adapter: board private struct 4559 * 4560 * code flow taken from tg3.c, called with e1000 interrupts disabled. 4561 **/ 4562 static int e1000_test_msi(struct e1000_adapter *adapter) 4563 { 4564 int err; 4565 u16 pci_cmd; 4566 4567 if (!(adapter->flags & FLAG_MSI_ENABLED)) 4568 return 0; 4569 4570 /* disable SERR in case the MSI write causes a master abort */ 4571 pci_read_config_word(adapter->pdev, PCI_COMMAND, &pci_cmd); 4572 if (pci_cmd & PCI_COMMAND_SERR) 4573 pci_write_config_word(adapter->pdev, PCI_COMMAND, 4574 pci_cmd & ~PCI_COMMAND_SERR); 4575 4576 err = e1000_test_msi_interrupt(adapter); 4577 4578 /* re-enable SERR */ 4579 if (pci_cmd & PCI_COMMAND_SERR) { 4580 pci_read_config_word(adapter->pdev, PCI_COMMAND, &pci_cmd); 4581 pci_cmd |= PCI_COMMAND_SERR; 4582 pci_write_config_word(adapter->pdev, PCI_COMMAND, pci_cmd); 4583 } 4584 4585 return err; 4586 } 4587 4588 /** 4589 * e1000e_open - Called when a network interface is made active 4590 * @netdev: network interface device structure 4591 * 4592 * Returns 0 on success, negative value on failure 4593 * 4594 * The open entry point is called when a network interface is made 4595 * active by the system (IFF_UP). At this point all resources needed 4596 * for transmit and receive operations are allocated, the interrupt 4597 * handler is registered with the OS, the watchdog timer is started, 4598 * and the stack is notified that the interface is ready. 4599 **/ 4600 int e1000e_open(struct net_device *netdev) 4601 { 4602 struct e1000_adapter *adapter = netdev_priv(netdev); 4603 struct e1000_hw *hw = &adapter->hw; 4604 struct pci_dev *pdev = adapter->pdev; 4605 int err; 4606 4607 /* disallow open during test */ 4608 if (test_bit(__E1000_TESTING, &adapter->state)) 4609 return -EBUSY; 4610 4611 pm_runtime_get_sync(&pdev->dev); 4612 4613 netif_carrier_off(netdev); 4614 netif_stop_queue(netdev); 4615 4616 /* allocate transmit descriptors */ 4617 err = e1000e_setup_tx_resources(adapter->tx_ring); 4618 if (err) 4619 goto err_setup_tx; 4620 4621 /* allocate receive descriptors */ 4622 err = e1000e_setup_rx_resources(adapter->rx_ring); 4623 if (err) 4624 goto err_setup_rx; 4625 4626 /* If AMT is enabled, let the firmware know that the network 4627 * interface is now open and reset the part to a known state. 4628 */ 4629 if (adapter->flags & FLAG_HAS_AMT) { 4630 e1000e_get_hw_control(adapter); 4631 e1000e_reset(adapter); 4632 } 4633 4634 e1000e_power_up_phy(adapter); 4635 4636 adapter->mng_vlan_id = E1000_MNG_VLAN_NONE; 4637 if ((adapter->hw.mng_cookie.status & E1000_MNG_DHCP_COOKIE_STATUS_VLAN)) 4638 e1000_update_mng_vlan(adapter); 4639 4640 /* DMA latency requirement to workaround jumbo issue */ 4641 cpu_latency_qos_add_request(&adapter->pm_qos_req, PM_QOS_DEFAULT_VALUE); 4642 4643 /* before we allocate an interrupt, we must be ready to handle it. 4644 * Setting DEBUG_SHIRQ in the kernel makes it fire an interrupt 4645 * as soon as we call pci_request_irq, so we have to setup our 4646 * clean_rx handler before we do so. 4647 */ 4648 e1000_configure(adapter); 4649 4650 err = e1000_request_irq(adapter); 4651 if (err) 4652 goto err_req_irq; 4653 4654 /* Work around PCIe errata with MSI interrupts causing some chipsets to 4655 * ignore e1000e MSI messages, which means we need to test our MSI 4656 * interrupt now 4657 */ 4658 if (adapter->int_mode != E1000E_INT_MODE_LEGACY) { 4659 err = e1000_test_msi(adapter); 4660 if (err) { 4661 e_err("Interrupt allocation failed\n"); 4662 goto err_req_irq; 4663 } 4664 } 4665 4666 /* From here on the code is the same as e1000e_up() */ 4667 clear_bit(__E1000_DOWN, &adapter->state); 4668 4669 napi_enable(&adapter->napi); 4670 4671 e1000_irq_enable(adapter); 4672 4673 adapter->tx_hang_recheck = false; 4674 4675 hw->mac.get_link_status = true; 4676 pm_runtime_put(&pdev->dev); 4677 4678 e1000e_trigger_lsc(adapter); 4679 4680 return 0; 4681 4682 err_req_irq: 4683 cpu_latency_qos_remove_request(&adapter->pm_qos_req); 4684 e1000e_release_hw_control(adapter); 4685 e1000_power_down_phy(adapter); 4686 e1000e_free_rx_resources(adapter->rx_ring); 4687 err_setup_rx: 4688 e1000e_free_tx_resources(adapter->tx_ring); 4689 err_setup_tx: 4690 e1000e_reset(adapter); 4691 pm_runtime_put_sync(&pdev->dev); 4692 4693 return err; 4694 } 4695 4696 /** 4697 * e1000e_close - Disables a network interface 4698 * @netdev: network interface device structure 4699 * 4700 * Returns 0, this is not allowed to fail 4701 * 4702 * The close entry point is called when an interface is de-activated 4703 * by the OS. The hardware is still under the drivers control, but 4704 * needs to be disabled. A global MAC reset is issued to stop the 4705 * hardware, and all transmit and receive resources are freed. 4706 **/ 4707 int e1000e_close(struct net_device *netdev) 4708 { 4709 struct e1000_adapter *adapter = netdev_priv(netdev); 4710 struct pci_dev *pdev = adapter->pdev; 4711 int count = E1000_CHECK_RESET_COUNT; 4712 4713 while (test_bit(__E1000_RESETTING, &adapter->state) && count--) 4714 usleep_range(10000, 11000); 4715 4716 WARN_ON(test_bit(__E1000_RESETTING, &adapter->state)); 4717 4718 pm_runtime_get_sync(&pdev->dev); 4719 4720 if (netif_device_present(netdev)) { 4721 e1000e_down(adapter, true); 4722 e1000_free_irq(adapter); 4723 4724 /* Link status message must follow this format */ 4725 netdev_info(netdev, "NIC Link is Down\n"); 4726 } 4727 4728 napi_disable(&adapter->napi); 4729 4730 e1000e_free_tx_resources(adapter->tx_ring); 4731 e1000e_free_rx_resources(adapter->rx_ring); 4732 4733 /* kill manageability vlan ID if supported, but not if a vlan with 4734 * the same ID is registered on the host OS (let 8021q kill it) 4735 */ 4736 if (adapter->hw.mng_cookie.status & E1000_MNG_DHCP_COOKIE_STATUS_VLAN) 4737 e1000_vlan_rx_kill_vid(netdev, htons(ETH_P_8021Q), 4738 adapter->mng_vlan_id); 4739 4740 /* If AMT is enabled, let the firmware know that the network 4741 * interface is now closed 4742 */ 4743 if ((adapter->flags & FLAG_HAS_AMT) && 4744 !test_bit(__E1000_TESTING, &adapter->state)) 4745 e1000e_release_hw_control(adapter); 4746 4747 cpu_latency_qos_remove_request(&adapter->pm_qos_req); 4748 4749 pm_runtime_put_sync(&pdev->dev); 4750 4751 return 0; 4752 } 4753 4754 /** 4755 * e1000_set_mac - Change the Ethernet Address of the NIC 4756 * @netdev: network interface device structure 4757 * @p: pointer to an address structure 4758 * 4759 * Returns 0 on success, negative on failure 4760 **/ 4761 static int e1000_set_mac(struct net_device *netdev, void *p) 4762 { 4763 struct e1000_adapter *adapter = netdev_priv(netdev); 4764 struct e1000_hw *hw = &adapter->hw; 4765 struct sockaddr *addr = p; 4766 4767 if (!is_valid_ether_addr(addr->sa_data)) 4768 return -EADDRNOTAVAIL; 4769 4770 memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len); 4771 memcpy(adapter->hw.mac.addr, addr->sa_data, netdev->addr_len); 4772 4773 hw->mac.ops.rar_set(&adapter->hw, adapter->hw.mac.addr, 0); 4774 4775 if (adapter->flags & FLAG_RESET_OVERWRITES_LAA) { 4776 /* activate the work around */ 4777 e1000e_set_laa_state_82571(&adapter->hw, 1); 4778 4779 /* Hold a copy of the LAA in RAR[14] This is done so that 4780 * between the time RAR[0] gets clobbered and the time it 4781 * gets fixed (in e1000_watchdog), the actual LAA is in one 4782 * of the RARs and no incoming packets directed to this port 4783 * are dropped. Eventually the LAA will be in RAR[0] and 4784 * RAR[14] 4785 */ 4786 hw->mac.ops.rar_set(&adapter->hw, adapter->hw.mac.addr, 4787 adapter->hw.mac.rar_entry_count - 1); 4788 } 4789 4790 return 0; 4791 } 4792 4793 /** 4794 * e1000e_update_phy_task - work thread to update phy 4795 * @work: pointer to our work struct 4796 * 4797 * this worker thread exists because we must acquire a 4798 * semaphore to read the phy, which we could msleep while 4799 * waiting for it, and we can't msleep in a timer. 4800 **/ 4801 static void e1000e_update_phy_task(struct work_struct *work) 4802 { 4803 struct e1000_adapter *adapter = container_of(work, 4804 struct e1000_adapter, 4805 update_phy_task); 4806 struct e1000_hw *hw = &adapter->hw; 4807 4808 if (test_bit(__E1000_DOWN, &adapter->state)) 4809 return; 4810 4811 e1000_get_phy_info(hw); 4812 4813 /* Enable EEE on 82579 after link up */ 4814 if (hw->phy.type >= e1000_phy_82579) 4815 e1000_set_eee_pchlan(hw); 4816 } 4817 4818 /** 4819 * e1000_update_phy_info - timre call-back to update PHY info 4820 * @data: pointer to adapter cast into an unsigned long 4821 * 4822 * Need to wait a few seconds after link up to get diagnostic information from 4823 * the phy 4824 **/ 4825 static void e1000_update_phy_info(struct timer_list *t) 4826 { 4827 struct e1000_adapter *adapter = from_timer(adapter, t, phy_info_timer); 4828 4829 if (test_bit(__E1000_DOWN, &adapter->state)) 4830 return; 4831 4832 schedule_work(&adapter->update_phy_task); 4833 } 4834 4835 /** 4836 * e1000e_update_phy_stats - Update the PHY statistics counters 4837 * @adapter: board private structure 4838 * 4839 * Read/clear the upper 16-bit PHY registers and read/accumulate lower 4840 **/ 4841 static void e1000e_update_phy_stats(struct e1000_adapter *adapter) 4842 { 4843 struct e1000_hw *hw = &adapter->hw; 4844 s32 ret_val; 4845 u16 phy_data; 4846 4847 ret_val = hw->phy.ops.acquire(hw); 4848 if (ret_val) 4849 return; 4850 4851 /* A page set is expensive so check if already on desired page. 4852 * If not, set to the page with the PHY status registers. 4853 */ 4854 hw->phy.addr = 1; 4855 ret_val = e1000e_read_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, 4856 &phy_data); 4857 if (ret_val) 4858 goto release; 4859 if (phy_data != (HV_STATS_PAGE << IGP_PAGE_SHIFT)) { 4860 ret_val = hw->phy.ops.set_page(hw, 4861 HV_STATS_PAGE << IGP_PAGE_SHIFT); 4862 if (ret_val) 4863 goto release; 4864 } 4865 4866 /* Single Collision Count */ 4867 hw->phy.ops.read_reg_page(hw, HV_SCC_UPPER, &phy_data); 4868 ret_val = hw->phy.ops.read_reg_page(hw, HV_SCC_LOWER, &phy_data); 4869 if (!ret_val) 4870 adapter->stats.scc += phy_data; 4871 4872 /* Excessive Collision Count */ 4873 hw->phy.ops.read_reg_page(hw, HV_ECOL_UPPER, &phy_data); 4874 ret_val = hw->phy.ops.read_reg_page(hw, HV_ECOL_LOWER, &phy_data); 4875 if (!ret_val) 4876 adapter->stats.ecol += phy_data; 4877 4878 /* Multiple Collision Count */ 4879 hw->phy.ops.read_reg_page(hw, HV_MCC_UPPER, &phy_data); 4880 ret_val = hw->phy.ops.read_reg_page(hw, HV_MCC_LOWER, &phy_data); 4881 if (!ret_val) 4882 adapter->stats.mcc += phy_data; 4883 4884 /* Late Collision Count */ 4885 hw->phy.ops.read_reg_page(hw, HV_LATECOL_UPPER, &phy_data); 4886 ret_val = hw->phy.ops.read_reg_page(hw, HV_LATECOL_LOWER, &phy_data); 4887 if (!ret_val) 4888 adapter->stats.latecol += phy_data; 4889 4890 /* Collision Count - also used for adaptive IFS */ 4891 hw->phy.ops.read_reg_page(hw, HV_COLC_UPPER, &phy_data); 4892 ret_val = hw->phy.ops.read_reg_page(hw, HV_COLC_LOWER, &phy_data); 4893 if (!ret_val) 4894 hw->mac.collision_delta = phy_data; 4895 4896 /* Defer Count */ 4897 hw->phy.ops.read_reg_page(hw, HV_DC_UPPER, &phy_data); 4898 ret_val = hw->phy.ops.read_reg_page(hw, HV_DC_LOWER, &phy_data); 4899 if (!ret_val) 4900 adapter->stats.dc += phy_data; 4901 4902 /* Transmit with no CRS */ 4903 hw->phy.ops.read_reg_page(hw, HV_TNCRS_UPPER, &phy_data); 4904 ret_val = hw->phy.ops.read_reg_page(hw, HV_TNCRS_LOWER, &phy_data); 4905 if (!ret_val) 4906 adapter->stats.tncrs += phy_data; 4907 4908 release: 4909 hw->phy.ops.release(hw); 4910 } 4911 4912 /** 4913 * e1000e_update_stats - Update the board statistics counters 4914 * @adapter: board private structure 4915 **/ 4916 static void e1000e_update_stats(struct e1000_adapter *adapter) 4917 { 4918 struct net_device *netdev = adapter->netdev; 4919 struct e1000_hw *hw = &adapter->hw; 4920 struct pci_dev *pdev = adapter->pdev; 4921 4922 /* Prevent stats update while adapter is being reset, or if the pci 4923 * connection is down. 4924 */ 4925 if (adapter->link_speed == 0) 4926 return; 4927 if (pci_channel_offline(pdev)) 4928 return; 4929 4930 adapter->stats.crcerrs += er32(CRCERRS); 4931 adapter->stats.gprc += er32(GPRC); 4932 adapter->stats.gorc += er32(GORCL); 4933 er32(GORCH); /* Clear gorc */ 4934 adapter->stats.bprc += er32(BPRC); 4935 adapter->stats.mprc += er32(MPRC); 4936 adapter->stats.roc += er32(ROC); 4937 4938 adapter->stats.mpc += er32(MPC); 4939 4940 /* Half-duplex statistics */ 4941 if (adapter->link_duplex == HALF_DUPLEX) { 4942 if (adapter->flags2 & FLAG2_HAS_PHY_STATS) { 4943 e1000e_update_phy_stats(adapter); 4944 } else { 4945 adapter->stats.scc += er32(SCC); 4946 adapter->stats.ecol += er32(ECOL); 4947 adapter->stats.mcc += er32(MCC); 4948 adapter->stats.latecol += er32(LATECOL); 4949 adapter->stats.dc += er32(DC); 4950 4951 hw->mac.collision_delta = er32(COLC); 4952 4953 if ((hw->mac.type != e1000_82574) && 4954 (hw->mac.type != e1000_82583)) 4955 adapter->stats.tncrs += er32(TNCRS); 4956 } 4957 adapter->stats.colc += hw->mac.collision_delta; 4958 } 4959 4960 adapter->stats.xonrxc += er32(XONRXC); 4961 adapter->stats.xontxc += er32(XONTXC); 4962 adapter->stats.xoffrxc += er32(XOFFRXC); 4963 adapter->stats.xofftxc += er32(XOFFTXC); 4964 adapter->stats.gptc += er32(GPTC); 4965 adapter->stats.gotc += er32(GOTCL); 4966 er32(GOTCH); /* Clear gotc */ 4967 adapter->stats.rnbc += er32(RNBC); 4968 adapter->stats.ruc += er32(RUC); 4969 4970 adapter->stats.mptc += er32(MPTC); 4971 adapter->stats.bptc += er32(BPTC); 4972 4973 /* used for adaptive IFS */ 4974 4975 hw->mac.tx_packet_delta = er32(TPT); 4976 adapter->stats.tpt += hw->mac.tx_packet_delta; 4977 4978 adapter->stats.algnerrc += er32(ALGNERRC); 4979 adapter->stats.rxerrc += er32(RXERRC); 4980 adapter->stats.cexterr += er32(CEXTERR); 4981 adapter->stats.tsctc += er32(TSCTC); 4982 adapter->stats.tsctfc += er32(TSCTFC); 4983 4984 /* Fill out the OS statistics structure */ 4985 netdev->stats.multicast = adapter->stats.mprc; 4986 netdev->stats.collisions = adapter->stats.colc; 4987 4988 /* Rx Errors */ 4989 4990 /* RLEC on some newer hardware can be incorrect so build 4991 * our own version based on RUC and ROC 4992 */ 4993 netdev->stats.rx_errors = adapter->stats.rxerrc + 4994 adapter->stats.crcerrs + adapter->stats.algnerrc + 4995 adapter->stats.ruc + adapter->stats.roc + adapter->stats.cexterr; 4996 netdev->stats.rx_length_errors = adapter->stats.ruc + 4997 adapter->stats.roc; 4998 netdev->stats.rx_crc_errors = adapter->stats.crcerrs; 4999 netdev->stats.rx_frame_errors = adapter->stats.algnerrc; 5000 netdev->stats.rx_missed_errors = adapter->stats.mpc; 5001 5002 /* Tx Errors */ 5003 netdev->stats.tx_errors = adapter->stats.ecol + adapter->stats.latecol; 5004 netdev->stats.tx_aborted_errors = adapter->stats.ecol; 5005 netdev->stats.tx_window_errors = adapter->stats.latecol; 5006 netdev->stats.tx_carrier_errors = adapter->stats.tncrs; 5007 5008 /* Tx Dropped needs to be maintained elsewhere */ 5009 5010 /* Management Stats */ 5011 adapter->stats.mgptc += er32(MGTPTC); 5012 adapter->stats.mgprc += er32(MGTPRC); 5013 adapter->stats.mgpdc += er32(MGTPDC); 5014 5015 /* Correctable ECC Errors */ 5016 if (hw->mac.type >= e1000_pch_lpt) { 5017 u32 pbeccsts = er32(PBECCSTS); 5018 5019 adapter->corr_errors += 5020 pbeccsts & E1000_PBECCSTS_CORR_ERR_CNT_MASK; 5021 adapter->uncorr_errors += 5022 (pbeccsts & E1000_PBECCSTS_UNCORR_ERR_CNT_MASK) >> 5023 E1000_PBECCSTS_UNCORR_ERR_CNT_SHIFT; 5024 } 5025 } 5026 5027 /** 5028 * e1000_phy_read_status - Update the PHY register status snapshot 5029 * @adapter: board private structure 5030 **/ 5031 static void e1000_phy_read_status(struct e1000_adapter *adapter) 5032 { 5033 struct e1000_hw *hw = &adapter->hw; 5034 struct e1000_phy_regs *phy = &adapter->phy_regs; 5035 5036 if (!pm_runtime_suspended((&adapter->pdev->dev)->parent) && 5037 (er32(STATUS) & E1000_STATUS_LU) && 5038 (adapter->hw.phy.media_type == e1000_media_type_copper)) { 5039 int ret_val; 5040 5041 ret_val = e1e_rphy(hw, MII_BMCR, &phy->bmcr); 5042 ret_val |= e1e_rphy(hw, MII_BMSR, &phy->bmsr); 5043 ret_val |= e1e_rphy(hw, MII_ADVERTISE, &phy->advertise); 5044 ret_val |= e1e_rphy(hw, MII_LPA, &phy->lpa); 5045 ret_val |= e1e_rphy(hw, MII_EXPANSION, &phy->expansion); 5046 ret_val |= e1e_rphy(hw, MII_CTRL1000, &phy->ctrl1000); 5047 ret_val |= e1e_rphy(hw, MII_STAT1000, &phy->stat1000); 5048 ret_val |= e1e_rphy(hw, MII_ESTATUS, &phy->estatus); 5049 if (ret_val) 5050 e_warn("Error reading PHY register\n"); 5051 } else { 5052 /* Do not read PHY registers if link is not up 5053 * Set values to typical power-on defaults 5054 */ 5055 phy->bmcr = (BMCR_SPEED1000 | BMCR_ANENABLE | BMCR_FULLDPLX); 5056 phy->bmsr = (BMSR_100FULL | BMSR_100HALF | BMSR_10FULL | 5057 BMSR_10HALF | BMSR_ESTATEN | BMSR_ANEGCAPABLE | 5058 BMSR_ERCAP); 5059 phy->advertise = (ADVERTISE_PAUSE_ASYM | ADVERTISE_PAUSE_CAP | 5060 ADVERTISE_ALL | ADVERTISE_CSMA); 5061 phy->lpa = 0; 5062 phy->expansion = EXPANSION_ENABLENPAGE; 5063 phy->ctrl1000 = ADVERTISE_1000FULL; 5064 phy->stat1000 = 0; 5065 phy->estatus = (ESTATUS_1000_TFULL | ESTATUS_1000_THALF); 5066 } 5067 } 5068 5069 static void e1000_print_link_info(struct e1000_adapter *adapter) 5070 { 5071 struct e1000_hw *hw = &adapter->hw; 5072 u32 ctrl = er32(CTRL); 5073 5074 /* Link status message must follow this format for user tools */ 5075 netdev_info(adapter->netdev, 5076 "NIC Link is Up %d Mbps %s Duplex, Flow Control: %s\n", 5077 adapter->link_speed, 5078 adapter->link_duplex == FULL_DUPLEX ? "Full" : "Half", 5079 (ctrl & E1000_CTRL_TFCE) && (ctrl & E1000_CTRL_RFCE) ? "Rx/Tx" : 5080 (ctrl & E1000_CTRL_RFCE) ? "Rx" : 5081 (ctrl & E1000_CTRL_TFCE) ? "Tx" : "None"); 5082 } 5083 5084 static bool e1000e_has_link(struct e1000_adapter *adapter) 5085 { 5086 struct e1000_hw *hw = &adapter->hw; 5087 bool link_active = false; 5088 s32 ret_val = 0; 5089 5090 /* get_link_status is set on LSC (link status) interrupt or 5091 * Rx sequence error interrupt. get_link_status will stay 5092 * true until the check_for_link establishes link 5093 * for copper adapters ONLY 5094 */ 5095 switch (hw->phy.media_type) { 5096 case e1000_media_type_copper: 5097 if (hw->mac.get_link_status) { 5098 ret_val = hw->mac.ops.check_for_link(hw); 5099 link_active = !hw->mac.get_link_status; 5100 } else { 5101 link_active = true; 5102 } 5103 break; 5104 case e1000_media_type_fiber: 5105 ret_val = hw->mac.ops.check_for_link(hw); 5106 link_active = !!(er32(STATUS) & E1000_STATUS_LU); 5107 break; 5108 case e1000_media_type_internal_serdes: 5109 ret_val = hw->mac.ops.check_for_link(hw); 5110 link_active = hw->mac.serdes_has_link; 5111 break; 5112 default: 5113 case e1000_media_type_unknown: 5114 break; 5115 } 5116 5117 if ((ret_val == -E1000_ERR_PHY) && (hw->phy.type == e1000_phy_igp_3) && 5118 (er32(CTRL) & E1000_PHY_CTRL_GBE_DISABLE)) { 5119 /* See e1000_kmrn_lock_loss_workaround_ich8lan() */ 5120 e_info("Gigabit has been disabled, downgrading speed\n"); 5121 } 5122 5123 return link_active; 5124 } 5125 5126 static void e1000e_enable_receives(struct e1000_adapter *adapter) 5127 { 5128 /* make sure the receive unit is started */ 5129 if ((adapter->flags & FLAG_RX_NEEDS_RESTART) && 5130 (adapter->flags & FLAG_RESTART_NOW)) { 5131 struct e1000_hw *hw = &adapter->hw; 5132 u32 rctl = er32(RCTL); 5133 5134 ew32(RCTL, rctl | E1000_RCTL_EN); 5135 adapter->flags &= ~FLAG_RESTART_NOW; 5136 } 5137 } 5138 5139 static void e1000e_check_82574_phy_workaround(struct e1000_adapter *adapter) 5140 { 5141 struct e1000_hw *hw = &adapter->hw; 5142 5143 /* With 82574 controllers, PHY needs to be checked periodically 5144 * for hung state and reset, if two calls return true 5145 */ 5146 if (e1000_check_phy_82574(hw)) 5147 adapter->phy_hang_count++; 5148 else 5149 adapter->phy_hang_count = 0; 5150 5151 if (adapter->phy_hang_count > 1) { 5152 adapter->phy_hang_count = 0; 5153 e_dbg("PHY appears hung - resetting\n"); 5154 schedule_work(&adapter->reset_task); 5155 } 5156 } 5157 5158 /** 5159 * e1000_watchdog - Timer Call-back 5160 * @data: pointer to adapter cast into an unsigned long 5161 **/ 5162 static void e1000_watchdog(struct timer_list *t) 5163 { 5164 struct e1000_adapter *adapter = from_timer(adapter, t, watchdog_timer); 5165 5166 /* Do the rest outside of interrupt context */ 5167 schedule_work(&adapter->watchdog_task); 5168 5169 /* TODO: make this use queue_delayed_work() */ 5170 } 5171 5172 static void e1000_watchdog_task(struct work_struct *work) 5173 { 5174 struct e1000_adapter *adapter = container_of(work, 5175 struct e1000_adapter, 5176 watchdog_task); 5177 struct net_device *netdev = adapter->netdev; 5178 struct e1000_mac_info *mac = &adapter->hw.mac; 5179 struct e1000_phy_info *phy = &adapter->hw.phy; 5180 struct e1000_ring *tx_ring = adapter->tx_ring; 5181 u32 dmoff_exit_timeout = 100, tries = 0; 5182 struct e1000_hw *hw = &adapter->hw; 5183 u32 link, tctl, pcim_state; 5184 5185 if (test_bit(__E1000_DOWN, &adapter->state)) 5186 return; 5187 5188 link = e1000e_has_link(adapter); 5189 if ((netif_carrier_ok(netdev)) && link) { 5190 /* Cancel scheduled suspend requests. */ 5191 pm_runtime_resume(netdev->dev.parent); 5192 5193 e1000e_enable_receives(adapter); 5194 goto link_up; 5195 } 5196 5197 if ((e1000e_enable_tx_pkt_filtering(hw)) && 5198 (adapter->mng_vlan_id != adapter->hw.mng_cookie.vlan_id)) 5199 e1000_update_mng_vlan(adapter); 5200 5201 if (link) { 5202 if (!netif_carrier_ok(netdev)) { 5203 bool txb2b = true; 5204 5205 /* Cancel scheduled suspend requests. */ 5206 pm_runtime_resume(netdev->dev.parent); 5207 5208 /* Checking if MAC is in DMoff state*/ 5209 pcim_state = er32(STATUS); 5210 while (pcim_state & E1000_STATUS_PCIM_STATE) { 5211 if (tries++ == dmoff_exit_timeout) { 5212 e_dbg("Error in exiting dmoff\n"); 5213 break; 5214 } 5215 usleep_range(10000, 20000); 5216 pcim_state = er32(STATUS); 5217 5218 /* Checking if MAC exited DMoff state */ 5219 if (!(pcim_state & E1000_STATUS_PCIM_STATE)) 5220 e1000_phy_hw_reset(&adapter->hw); 5221 } 5222 5223 /* update snapshot of PHY registers on LSC */ 5224 e1000_phy_read_status(adapter); 5225 mac->ops.get_link_up_info(&adapter->hw, 5226 &adapter->link_speed, 5227 &adapter->link_duplex); 5228 e1000_print_link_info(adapter); 5229 5230 /* check if SmartSpeed worked */ 5231 e1000e_check_downshift(hw); 5232 if (phy->speed_downgraded) 5233 netdev_warn(netdev, 5234 "Link Speed was downgraded by SmartSpeed\n"); 5235 5236 /* On supported PHYs, check for duplex mismatch only 5237 * if link has autonegotiated at 10/100 half 5238 */ 5239 if ((hw->phy.type == e1000_phy_igp_3 || 5240 hw->phy.type == e1000_phy_bm) && 5241 hw->mac.autoneg && 5242 (adapter->link_speed == SPEED_10 || 5243 adapter->link_speed == SPEED_100) && 5244 (adapter->link_duplex == HALF_DUPLEX)) { 5245 u16 autoneg_exp; 5246 5247 e1e_rphy(hw, MII_EXPANSION, &autoneg_exp); 5248 5249 if (!(autoneg_exp & EXPANSION_NWAY)) 5250 e_info("Autonegotiated half duplex but link partner cannot autoneg. Try forcing full duplex if link gets many collisions.\n"); 5251 } 5252 5253 /* adjust timeout factor according to speed/duplex */ 5254 adapter->tx_timeout_factor = 1; 5255 switch (adapter->link_speed) { 5256 case SPEED_10: 5257 txb2b = false; 5258 adapter->tx_timeout_factor = 16; 5259 break; 5260 case SPEED_100: 5261 txb2b = false; 5262 adapter->tx_timeout_factor = 10; 5263 break; 5264 } 5265 5266 /* workaround: re-program speed mode bit after 5267 * link-up event 5268 */ 5269 if ((adapter->flags & FLAG_TARC_SPEED_MODE_BIT) && 5270 !txb2b) { 5271 u32 tarc0; 5272 5273 tarc0 = er32(TARC(0)); 5274 tarc0 &= ~SPEED_MODE_BIT; 5275 ew32(TARC(0), tarc0); 5276 } 5277 5278 /* disable TSO for pcie and 10/100 speeds, to avoid 5279 * some hardware issues 5280 */ 5281 if (!(adapter->flags & FLAG_TSO_FORCE)) { 5282 switch (adapter->link_speed) { 5283 case SPEED_10: 5284 case SPEED_100: 5285 e_info("10/100 speed: disabling TSO\n"); 5286 netdev->features &= ~NETIF_F_TSO; 5287 netdev->features &= ~NETIF_F_TSO6; 5288 break; 5289 case SPEED_1000: 5290 netdev->features |= NETIF_F_TSO; 5291 netdev->features |= NETIF_F_TSO6; 5292 break; 5293 default: 5294 /* oops */ 5295 break; 5296 } 5297 } 5298 5299 /* enable transmits in the hardware, need to do this 5300 * after setting TARC(0) 5301 */ 5302 tctl = er32(TCTL); 5303 tctl |= E1000_TCTL_EN; 5304 ew32(TCTL, tctl); 5305 5306 /* Perform any post-link-up configuration before 5307 * reporting link up. 5308 */ 5309 if (phy->ops.cfg_on_link_up) 5310 phy->ops.cfg_on_link_up(hw); 5311 5312 netif_wake_queue(netdev); 5313 netif_carrier_on(netdev); 5314 5315 if (!test_bit(__E1000_DOWN, &adapter->state)) 5316 mod_timer(&adapter->phy_info_timer, 5317 round_jiffies(jiffies + 2 * HZ)); 5318 } 5319 } else { 5320 if (netif_carrier_ok(netdev)) { 5321 adapter->link_speed = 0; 5322 adapter->link_duplex = 0; 5323 /* Link status message must follow this format */ 5324 netdev_info(netdev, "NIC Link is Down\n"); 5325 netif_carrier_off(netdev); 5326 netif_stop_queue(netdev); 5327 if (!test_bit(__E1000_DOWN, &adapter->state)) 5328 mod_timer(&adapter->phy_info_timer, 5329 round_jiffies(jiffies + 2 * HZ)); 5330 5331 /* 8000ES2LAN requires a Rx packet buffer work-around 5332 * on link down event; reset the controller to flush 5333 * the Rx packet buffer. 5334 */ 5335 if (adapter->flags & FLAG_RX_NEEDS_RESTART) 5336 adapter->flags |= FLAG_RESTART_NOW; 5337 else 5338 pm_schedule_suspend(netdev->dev.parent, 5339 LINK_TIMEOUT); 5340 } 5341 } 5342 5343 link_up: 5344 spin_lock(&adapter->stats64_lock); 5345 e1000e_update_stats(adapter); 5346 5347 mac->tx_packet_delta = adapter->stats.tpt - adapter->tpt_old; 5348 adapter->tpt_old = adapter->stats.tpt; 5349 mac->collision_delta = adapter->stats.colc - adapter->colc_old; 5350 adapter->colc_old = adapter->stats.colc; 5351 5352 adapter->gorc = adapter->stats.gorc - adapter->gorc_old; 5353 adapter->gorc_old = adapter->stats.gorc; 5354 adapter->gotc = adapter->stats.gotc - adapter->gotc_old; 5355 adapter->gotc_old = adapter->stats.gotc; 5356 spin_unlock(&adapter->stats64_lock); 5357 5358 /* If the link is lost the controller stops DMA, but 5359 * if there is queued Tx work it cannot be done. So 5360 * reset the controller to flush the Tx packet buffers. 5361 */ 5362 if (!netif_carrier_ok(netdev) && 5363 (e1000_desc_unused(tx_ring) + 1 < tx_ring->count)) 5364 adapter->flags |= FLAG_RESTART_NOW; 5365 5366 /* If reset is necessary, do it outside of interrupt context. */ 5367 if (adapter->flags & FLAG_RESTART_NOW) { 5368 schedule_work(&adapter->reset_task); 5369 /* return immediately since reset is imminent */ 5370 return; 5371 } 5372 5373 e1000e_update_adaptive(&adapter->hw); 5374 5375 /* Simple mode for Interrupt Throttle Rate (ITR) */ 5376 if (adapter->itr_setting == 4) { 5377 /* Symmetric Tx/Rx gets a reduced ITR=2000; 5378 * Total asymmetrical Tx or Rx gets ITR=8000; 5379 * everyone else is between 2000-8000. 5380 */ 5381 u32 goc = (adapter->gotc + adapter->gorc) / 10000; 5382 u32 dif = (adapter->gotc > adapter->gorc ? 5383 adapter->gotc - adapter->gorc : 5384 adapter->gorc - adapter->gotc) / 10000; 5385 u32 itr = goc > 0 ? (dif * 6000 / goc + 2000) : 8000; 5386 5387 e1000e_write_itr(adapter, itr); 5388 } 5389 5390 /* Cause software interrupt to ensure Rx ring is cleaned */ 5391 if (adapter->msix_entries) 5392 ew32(ICS, adapter->rx_ring->ims_val); 5393 else 5394 ew32(ICS, E1000_ICS_RXDMT0); 5395 5396 /* flush pending descriptors to memory before detecting Tx hang */ 5397 e1000e_flush_descriptors(adapter); 5398 5399 /* Force detection of hung controller every watchdog period */ 5400 adapter->detect_tx_hung = true; 5401 5402 /* With 82571 controllers, LAA may be overwritten due to controller 5403 * reset from the other port. Set the appropriate LAA in RAR[0] 5404 */ 5405 if (e1000e_get_laa_state_82571(hw)) 5406 hw->mac.ops.rar_set(hw, adapter->hw.mac.addr, 0); 5407 5408 if (adapter->flags2 & FLAG2_CHECK_PHY_HANG) 5409 e1000e_check_82574_phy_workaround(adapter); 5410 5411 /* Clear valid timestamp stuck in RXSTMPL/H due to a Rx error */ 5412 if (adapter->hwtstamp_config.rx_filter != HWTSTAMP_FILTER_NONE) { 5413 if ((adapter->flags2 & FLAG2_CHECK_RX_HWTSTAMP) && 5414 (er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_VALID)) { 5415 er32(RXSTMPH); 5416 adapter->rx_hwtstamp_cleared++; 5417 } else { 5418 adapter->flags2 |= FLAG2_CHECK_RX_HWTSTAMP; 5419 } 5420 } 5421 5422 /* Reset the timer */ 5423 if (!test_bit(__E1000_DOWN, &adapter->state)) 5424 mod_timer(&adapter->watchdog_timer, 5425 round_jiffies(jiffies + 2 * HZ)); 5426 } 5427 5428 #define E1000_TX_FLAGS_CSUM 0x00000001 5429 #define E1000_TX_FLAGS_VLAN 0x00000002 5430 #define E1000_TX_FLAGS_TSO 0x00000004 5431 #define E1000_TX_FLAGS_IPV4 0x00000008 5432 #define E1000_TX_FLAGS_NO_FCS 0x00000010 5433 #define E1000_TX_FLAGS_HWTSTAMP 0x00000020 5434 #define E1000_TX_FLAGS_VLAN_MASK 0xffff0000 5435 #define E1000_TX_FLAGS_VLAN_SHIFT 16 5436 5437 static int e1000_tso(struct e1000_ring *tx_ring, struct sk_buff *skb, 5438 __be16 protocol) 5439 { 5440 struct e1000_context_desc *context_desc; 5441 struct e1000_buffer *buffer_info; 5442 unsigned int i; 5443 u32 cmd_length = 0; 5444 u16 ipcse = 0, mss; 5445 u8 ipcss, ipcso, tucss, tucso, hdr_len; 5446 int err; 5447 5448 if (!skb_is_gso(skb)) 5449 return 0; 5450 5451 err = skb_cow_head(skb, 0); 5452 if (err < 0) 5453 return err; 5454 5455 hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb); 5456 mss = skb_shinfo(skb)->gso_size; 5457 if (protocol == htons(ETH_P_IP)) { 5458 struct iphdr *iph = ip_hdr(skb); 5459 iph->tot_len = 0; 5460 iph->check = 0; 5461 tcp_hdr(skb)->check = ~csum_tcpudp_magic(iph->saddr, iph->daddr, 5462 0, IPPROTO_TCP, 0); 5463 cmd_length = E1000_TXD_CMD_IP; 5464 ipcse = skb_transport_offset(skb) - 1; 5465 } else if (skb_is_gso_v6(skb)) { 5466 tcp_v6_gso_csum_prep(skb); 5467 ipcse = 0; 5468 } 5469 ipcss = skb_network_offset(skb); 5470 ipcso = (void *)&(ip_hdr(skb)->check) - (void *)skb->data; 5471 tucss = skb_transport_offset(skb); 5472 tucso = (void *)&(tcp_hdr(skb)->check) - (void *)skb->data; 5473 5474 cmd_length |= (E1000_TXD_CMD_DEXT | E1000_TXD_CMD_TSE | 5475 E1000_TXD_CMD_TCP | (skb->len - (hdr_len))); 5476 5477 i = tx_ring->next_to_use; 5478 context_desc = E1000_CONTEXT_DESC(*tx_ring, i); 5479 buffer_info = &tx_ring->buffer_info[i]; 5480 5481 context_desc->lower_setup.ip_fields.ipcss = ipcss; 5482 context_desc->lower_setup.ip_fields.ipcso = ipcso; 5483 context_desc->lower_setup.ip_fields.ipcse = cpu_to_le16(ipcse); 5484 context_desc->upper_setup.tcp_fields.tucss = tucss; 5485 context_desc->upper_setup.tcp_fields.tucso = tucso; 5486 context_desc->upper_setup.tcp_fields.tucse = 0; 5487 context_desc->tcp_seg_setup.fields.mss = cpu_to_le16(mss); 5488 context_desc->tcp_seg_setup.fields.hdr_len = hdr_len; 5489 context_desc->cmd_and_length = cpu_to_le32(cmd_length); 5490 5491 buffer_info->time_stamp = jiffies; 5492 buffer_info->next_to_watch = i; 5493 5494 i++; 5495 if (i == tx_ring->count) 5496 i = 0; 5497 tx_ring->next_to_use = i; 5498 5499 return 1; 5500 } 5501 5502 static bool e1000_tx_csum(struct e1000_ring *tx_ring, struct sk_buff *skb, 5503 __be16 protocol) 5504 { 5505 struct e1000_adapter *adapter = tx_ring->adapter; 5506 struct e1000_context_desc *context_desc; 5507 struct e1000_buffer *buffer_info; 5508 unsigned int i; 5509 u8 css; 5510 u32 cmd_len = E1000_TXD_CMD_DEXT; 5511 5512 if (skb->ip_summed != CHECKSUM_PARTIAL) 5513 return false; 5514 5515 switch (protocol) { 5516 case cpu_to_be16(ETH_P_IP): 5517 if (ip_hdr(skb)->protocol == IPPROTO_TCP) 5518 cmd_len |= E1000_TXD_CMD_TCP; 5519 break; 5520 case cpu_to_be16(ETH_P_IPV6): 5521 /* XXX not handling all IPV6 headers */ 5522 if (ipv6_hdr(skb)->nexthdr == IPPROTO_TCP) 5523 cmd_len |= E1000_TXD_CMD_TCP; 5524 break; 5525 default: 5526 if (unlikely(net_ratelimit())) 5527 e_warn("checksum_partial proto=%x!\n", 5528 be16_to_cpu(protocol)); 5529 break; 5530 } 5531 5532 css = skb_checksum_start_offset(skb); 5533 5534 i = tx_ring->next_to_use; 5535 buffer_info = &tx_ring->buffer_info[i]; 5536 context_desc = E1000_CONTEXT_DESC(*tx_ring, i); 5537 5538 context_desc->lower_setup.ip_config = 0; 5539 context_desc->upper_setup.tcp_fields.tucss = css; 5540 context_desc->upper_setup.tcp_fields.tucso = css + skb->csum_offset; 5541 context_desc->upper_setup.tcp_fields.tucse = 0; 5542 context_desc->tcp_seg_setup.data = 0; 5543 context_desc->cmd_and_length = cpu_to_le32(cmd_len); 5544 5545 buffer_info->time_stamp = jiffies; 5546 buffer_info->next_to_watch = i; 5547 5548 i++; 5549 if (i == tx_ring->count) 5550 i = 0; 5551 tx_ring->next_to_use = i; 5552 5553 return true; 5554 } 5555 5556 static int e1000_tx_map(struct e1000_ring *tx_ring, struct sk_buff *skb, 5557 unsigned int first, unsigned int max_per_txd, 5558 unsigned int nr_frags) 5559 { 5560 struct e1000_adapter *adapter = tx_ring->adapter; 5561 struct pci_dev *pdev = adapter->pdev; 5562 struct e1000_buffer *buffer_info; 5563 unsigned int len = skb_headlen(skb); 5564 unsigned int offset = 0, size, count = 0, i; 5565 unsigned int f, bytecount, segs; 5566 5567 i = tx_ring->next_to_use; 5568 5569 while (len) { 5570 buffer_info = &tx_ring->buffer_info[i]; 5571 size = min(len, max_per_txd); 5572 5573 buffer_info->length = size; 5574 buffer_info->time_stamp = jiffies; 5575 buffer_info->next_to_watch = i; 5576 buffer_info->dma = dma_map_single(&pdev->dev, 5577 skb->data + offset, 5578 size, DMA_TO_DEVICE); 5579 buffer_info->mapped_as_page = false; 5580 if (dma_mapping_error(&pdev->dev, buffer_info->dma)) 5581 goto dma_error; 5582 5583 len -= size; 5584 offset += size; 5585 count++; 5586 5587 if (len) { 5588 i++; 5589 if (i == tx_ring->count) 5590 i = 0; 5591 } 5592 } 5593 5594 for (f = 0; f < nr_frags; f++) { 5595 const skb_frag_t *frag = &skb_shinfo(skb)->frags[f]; 5596 5597 len = skb_frag_size(frag); 5598 offset = 0; 5599 5600 while (len) { 5601 i++; 5602 if (i == tx_ring->count) 5603 i = 0; 5604 5605 buffer_info = &tx_ring->buffer_info[i]; 5606 size = min(len, max_per_txd); 5607 5608 buffer_info->length = size; 5609 buffer_info->time_stamp = jiffies; 5610 buffer_info->next_to_watch = i; 5611 buffer_info->dma = skb_frag_dma_map(&pdev->dev, frag, 5612 offset, size, 5613 DMA_TO_DEVICE); 5614 buffer_info->mapped_as_page = true; 5615 if (dma_mapping_error(&pdev->dev, buffer_info->dma)) 5616 goto dma_error; 5617 5618 len -= size; 5619 offset += size; 5620 count++; 5621 } 5622 } 5623 5624 segs = skb_shinfo(skb)->gso_segs ? : 1; 5625 /* multiply data chunks by size of headers */ 5626 bytecount = ((segs - 1) * skb_headlen(skb)) + skb->len; 5627 5628 tx_ring->buffer_info[i].skb = skb; 5629 tx_ring->buffer_info[i].segs = segs; 5630 tx_ring->buffer_info[i].bytecount = bytecount; 5631 tx_ring->buffer_info[first].next_to_watch = i; 5632 5633 return count; 5634 5635 dma_error: 5636 dev_err(&pdev->dev, "Tx DMA map failed\n"); 5637 buffer_info->dma = 0; 5638 if (count) 5639 count--; 5640 5641 while (count--) { 5642 if (i == 0) 5643 i += tx_ring->count; 5644 i--; 5645 buffer_info = &tx_ring->buffer_info[i]; 5646 e1000_put_txbuf(tx_ring, buffer_info, true); 5647 } 5648 5649 return 0; 5650 } 5651 5652 static void e1000_tx_queue(struct e1000_ring *tx_ring, int tx_flags, int count) 5653 { 5654 struct e1000_adapter *adapter = tx_ring->adapter; 5655 struct e1000_tx_desc *tx_desc = NULL; 5656 struct e1000_buffer *buffer_info; 5657 u32 txd_upper = 0, txd_lower = E1000_TXD_CMD_IFCS; 5658 unsigned int i; 5659 5660 if (tx_flags & E1000_TX_FLAGS_TSO) { 5661 txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D | 5662 E1000_TXD_CMD_TSE; 5663 txd_upper |= E1000_TXD_POPTS_TXSM << 8; 5664 5665 if (tx_flags & E1000_TX_FLAGS_IPV4) 5666 txd_upper |= E1000_TXD_POPTS_IXSM << 8; 5667 } 5668 5669 if (tx_flags & E1000_TX_FLAGS_CSUM) { 5670 txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D; 5671 txd_upper |= E1000_TXD_POPTS_TXSM << 8; 5672 } 5673 5674 if (tx_flags & E1000_TX_FLAGS_VLAN) { 5675 txd_lower |= E1000_TXD_CMD_VLE; 5676 txd_upper |= (tx_flags & E1000_TX_FLAGS_VLAN_MASK); 5677 } 5678 5679 if (unlikely(tx_flags & E1000_TX_FLAGS_NO_FCS)) 5680 txd_lower &= ~(E1000_TXD_CMD_IFCS); 5681 5682 if (unlikely(tx_flags & E1000_TX_FLAGS_HWTSTAMP)) { 5683 txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D; 5684 txd_upper |= E1000_TXD_EXTCMD_TSTAMP; 5685 } 5686 5687 i = tx_ring->next_to_use; 5688 5689 do { 5690 buffer_info = &tx_ring->buffer_info[i]; 5691 tx_desc = E1000_TX_DESC(*tx_ring, i); 5692 tx_desc->buffer_addr = cpu_to_le64(buffer_info->dma); 5693 tx_desc->lower.data = cpu_to_le32(txd_lower | 5694 buffer_info->length); 5695 tx_desc->upper.data = cpu_to_le32(txd_upper); 5696 5697 i++; 5698 if (i == tx_ring->count) 5699 i = 0; 5700 } while (--count > 0); 5701 5702 tx_desc->lower.data |= cpu_to_le32(adapter->txd_cmd); 5703 5704 /* txd_cmd re-enables FCS, so we'll re-disable it here as desired. */ 5705 if (unlikely(tx_flags & E1000_TX_FLAGS_NO_FCS)) 5706 tx_desc->lower.data &= ~(cpu_to_le32(E1000_TXD_CMD_IFCS)); 5707 5708 /* Force memory writes to complete before letting h/w 5709 * know there are new descriptors to fetch. (Only 5710 * applicable for weak-ordered memory model archs, 5711 * such as IA-64). 5712 */ 5713 wmb(); 5714 5715 tx_ring->next_to_use = i; 5716 } 5717 5718 #define MINIMUM_DHCP_PACKET_SIZE 282 5719 static int e1000_transfer_dhcp_info(struct e1000_adapter *adapter, 5720 struct sk_buff *skb) 5721 { 5722 struct e1000_hw *hw = &adapter->hw; 5723 u16 length, offset; 5724 5725 if (skb_vlan_tag_present(skb) && 5726 !((skb_vlan_tag_get(skb) == adapter->hw.mng_cookie.vlan_id) && 5727 (adapter->hw.mng_cookie.status & 5728 E1000_MNG_DHCP_COOKIE_STATUS_VLAN))) 5729 return 0; 5730 5731 if (skb->len <= MINIMUM_DHCP_PACKET_SIZE) 5732 return 0; 5733 5734 if (((struct ethhdr *)skb->data)->h_proto != htons(ETH_P_IP)) 5735 return 0; 5736 5737 { 5738 const struct iphdr *ip = (struct iphdr *)((u8 *)skb->data + 14); 5739 struct udphdr *udp; 5740 5741 if (ip->protocol != IPPROTO_UDP) 5742 return 0; 5743 5744 udp = (struct udphdr *)((u8 *)ip + (ip->ihl << 2)); 5745 if (ntohs(udp->dest) != 67) 5746 return 0; 5747 5748 offset = (u8 *)udp + 8 - skb->data; 5749 length = skb->len - offset; 5750 return e1000e_mng_write_dhcp_info(hw, (u8 *)udp + 8, length); 5751 } 5752 5753 return 0; 5754 } 5755 5756 static int __e1000_maybe_stop_tx(struct e1000_ring *tx_ring, int size) 5757 { 5758 struct e1000_adapter *adapter = tx_ring->adapter; 5759 5760 netif_stop_queue(adapter->netdev); 5761 /* Herbert's original patch had: 5762 * smp_mb__after_netif_stop_queue(); 5763 * but since that doesn't exist yet, just open code it. 5764 */ 5765 smp_mb(); 5766 5767 /* We need to check again in a case another CPU has just 5768 * made room available. 5769 */ 5770 if (e1000_desc_unused(tx_ring) < size) 5771 return -EBUSY; 5772 5773 /* A reprieve! */ 5774 netif_start_queue(adapter->netdev); 5775 ++adapter->restart_queue; 5776 return 0; 5777 } 5778 5779 static int e1000_maybe_stop_tx(struct e1000_ring *tx_ring, int size) 5780 { 5781 BUG_ON(size > tx_ring->count); 5782 5783 if (e1000_desc_unused(tx_ring) >= size) 5784 return 0; 5785 return __e1000_maybe_stop_tx(tx_ring, size); 5786 } 5787 5788 static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb, 5789 struct net_device *netdev) 5790 { 5791 struct e1000_adapter *adapter = netdev_priv(netdev); 5792 struct e1000_ring *tx_ring = adapter->tx_ring; 5793 unsigned int first; 5794 unsigned int tx_flags = 0; 5795 unsigned int len = skb_headlen(skb); 5796 unsigned int nr_frags; 5797 unsigned int mss; 5798 int count = 0; 5799 int tso; 5800 unsigned int f; 5801 __be16 protocol = vlan_get_protocol(skb); 5802 5803 if (test_bit(__E1000_DOWN, &adapter->state)) { 5804 dev_kfree_skb_any(skb); 5805 return NETDEV_TX_OK; 5806 } 5807 5808 if (skb->len <= 0) { 5809 dev_kfree_skb_any(skb); 5810 return NETDEV_TX_OK; 5811 } 5812 5813 /* The minimum packet size with TCTL.PSP set is 17 bytes so 5814 * pad skb in order to meet this minimum size requirement 5815 */ 5816 if (skb_put_padto(skb, 17)) 5817 return NETDEV_TX_OK; 5818 5819 mss = skb_shinfo(skb)->gso_size; 5820 if (mss) { 5821 u8 hdr_len; 5822 5823 /* TSO Workaround for 82571/2/3 Controllers -- if skb->data 5824 * points to just header, pull a few bytes of payload from 5825 * frags into skb->data 5826 */ 5827 hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb); 5828 /* we do this workaround for ES2LAN, but it is un-necessary, 5829 * avoiding it could save a lot of cycles 5830 */ 5831 if (skb->data_len && (hdr_len == len)) { 5832 unsigned int pull_size; 5833 5834 pull_size = min_t(unsigned int, 4, skb->data_len); 5835 if (!__pskb_pull_tail(skb, pull_size)) { 5836 e_err("__pskb_pull_tail failed.\n"); 5837 dev_kfree_skb_any(skb); 5838 return NETDEV_TX_OK; 5839 } 5840 len = skb_headlen(skb); 5841 } 5842 } 5843 5844 /* reserve a descriptor for the offload context */ 5845 if ((mss) || (skb->ip_summed == CHECKSUM_PARTIAL)) 5846 count++; 5847 count++; 5848 5849 count += DIV_ROUND_UP(len, adapter->tx_fifo_limit); 5850 5851 nr_frags = skb_shinfo(skb)->nr_frags; 5852 for (f = 0; f < nr_frags; f++) 5853 count += DIV_ROUND_UP(skb_frag_size(&skb_shinfo(skb)->frags[f]), 5854 adapter->tx_fifo_limit); 5855 5856 if (adapter->hw.mac.tx_pkt_filtering) 5857 e1000_transfer_dhcp_info(adapter, skb); 5858 5859 /* need: count + 2 desc gap to keep tail from touching 5860 * head, otherwise try next time 5861 */ 5862 if (e1000_maybe_stop_tx(tx_ring, count + 2)) 5863 return NETDEV_TX_BUSY; 5864 5865 if (skb_vlan_tag_present(skb)) { 5866 tx_flags |= E1000_TX_FLAGS_VLAN; 5867 tx_flags |= (skb_vlan_tag_get(skb) << 5868 E1000_TX_FLAGS_VLAN_SHIFT); 5869 } 5870 5871 first = tx_ring->next_to_use; 5872 5873 tso = e1000_tso(tx_ring, skb, protocol); 5874 if (tso < 0) { 5875 dev_kfree_skb_any(skb); 5876 return NETDEV_TX_OK; 5877 } 5878 5879 if (tso) 5880 tx_flags |= E1000_TX_FLAGS_TSO; 5881 else if (e1000_tx_csum(tx_ring, skb, protocol)) 5882 tx_flags |= E1000_TX_FLAGS_CSUM; 5883 5884 /* Old method was to assume IPv4 packet by default if TSO was enabled. 5885 * 82571 hardware supports TSO capabilities for IPv6 as well... 5886 * no longer assume, we must. 5887 */ 5888 if (protocol == htons(ETH_P_IP)) 5889 tx_flags |= E1000_TX_FLAGS_IPV4; 5890 5891 if (unlikely(skb->no_fcs)) 5892 tx_flags |= E1000_TX_FLAGS_NO_FCS; 5893 5894 /* if count is 0 then mapping error has occurred */ 5895 count = e1000_tx_map(tx_ring, skb, first, adapter->tx_fifo_limit, 5896 nr_frags); 5897 if (count) { 5898 if (unlikely(skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP) && 5899 (adapter->flags & FLAG_HAS_HW_TIMESTAMP)) { 5900 if (!adapter->tx_hwtstamp_skb) { 5901 skb_shinfo(skb)->tx_flags |= SKBTX_IN_PROGRESS; 5902 tx_flags |= E1000_TX_FLAGS_HWTSTAMP; 5903 adapter->tx_hwtstamp_skb = skb_get(skb); 5904 adapter->tx_hwtstamp_start = jiffies; 5905 schedule_work(&adapter->tx_hwtstamp_work); 5906 } else { 5907 adapter->tx_hwtstamp_skipped++; 5908 } 5909 } 5910 5911 skb_tx_timestamp(skb); 5912 5913 netdev_sent_queue(netdev, skb->len); 5914 e1000_tx_queue(tx_ring, tx_flags, count); 5915 /* Make sure there is space in the ring for the next send. */ 5916 e1000_maybe_stop_tx(tx_ring, 5917 (MAX_SKB_FRAGS * 5918 DIV_ROUND_UP(PAGE_SIZE, 5919 adapter->tx_fifo_limit) + 2)); 5920 5921 if (!netdev_xmit_more() || 5922 netif_xmit_stopped(netdev_get_tx_queue(netdev, 0))) { 5923 if (adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA) 5924 e1000e_update_tdt_wa(tx_ring, 5925 tx_ring->next_to_use); 5926 else 5927 writel(tx_ring->next_to_use, tx_ring->tail); 5928 } 5929 } else { 5930 dev_kfree_skb_any(skb); 5931 tx_ring->buffer_info[first].time_stamp = 0; 5932 tx_ring->next_to_use = first; 5933 } 5934 5935 return NETDEV_TX_OK; 5936 } 5937 5938 /** 5939 * e1000_tx_timeout - Respond to a Tx Hang 5940 * @netdev: network interface device structure 5941 **/ 5942 static void e1000_tx_timeout(struct net_device *netdev, unsigned int txqueue) 5943 { 5944 struct e1000_adapter *adapter = netdev_priv(netdev); 5945 5946 /* Do the reset outside of interrupt context */ 5947 adapter->tx_timeout_count++; 5948 schedule_work(&adapter->reset_task); 5949 } 5950 5951 static void e1000_reset_task(struct work_struct *work) 5952 { 5953 struct e1000_adapter *adapter; 5954 adapter = container_of(work, struct e1000_adapter, reset_task); 5955 5956 /* don't run the task if already down */ 5957 if (test_bit(__E1000_DOWN, &adapter->state)) 5958 return; 5959 5960 if (!(adapter->flags & FLAG_RESTART_NOW)) { 5961 e1000e_dump(adapter); 5962 e_err("Reset adapter unexpectedly\n"); 5963 } 5964 e1000e_reinit_locked(adapter); 5965 } 5966 5967 /** 5968 * e1000_get_stats64 - Get System Network Statistics 5969 * @netdev: network interface device structure 5970 * @stats: rtnl_link_stats64 pointer 5971 * 5972 * Returns the address of the device statistics structure. 5973 **/ 5974 void e1000e_get_stats64(struct net_device *netdev, 5975 struct rtnl_link_stats64 *stats) 5976 { 5977 struct e1000_adapter *adapter = netdev_priv(netdev); 5978 5979 spin_lock(&adapter->stats64_lock); 5980 e1000e_update_stats(adapter); 5981 /* Fill out the OS statistics structure */ 5982 stats->rx_bytes = adapter->stats.gorc; 5983 stats->rx_packets = adapter->stats.gprc; 5984 stats->tx_bytes = adapter->stats.gotc; 5985 stats->tx_packets = adapter->stats.gptc; 5986 stats->multicast = adapter->stats.mprc; 5987 stats->collisions = adapter->stats.colc; 5988 5989 /* Rx Errors */ 5990 5991 /* RLEC on some newer hardware can be incorrect so build 5992 * our own version based on RUC and ROC 5993 */ 5994 stats->rx_errors = adapter->stats.rxerrc + 5995 adapter->stats.crcerrs + adapter->stats.algnerrc + 5996 adapter->stats.ruc + adapter->stats.roc + adapter->stats.cexterr; 5997 stats->rx_length_errors = adapter->stats.ruc + adapter->stats.roc; 5998 stats->rx_crc_errors = adapter->stats.crcerrs; 5999 stats->rx_frame_errors = adapter->stats.algnerrc; 6000 stats->rx_missed_errors = adapter->stats.mpc; 6001 6002 /* Tx Errors */ 6003 stats->tx_errors = adapter->stats.ecol + adapter->stats.latecol; 6004 stats->tx_aborted_errors = adapter->stats.ecol; 6005 stats->tx_window_errors = adapter->stats.latecol; 6006 stats->tx_carrier_errors = adapter->stats.tncrs; 6007 6008 /* Tx Dropped needs to be maintained elsewhere */ 6009 6010 spin_unlock(&adapter->stats64_lock); 6011 } 6012 6013 /** 6014 * e1000_change_mtu - Change the Maximum Transfer Unit 6015 * @netdev: network interface device structure 6016 * @new_mtu: new value for maximum frame size 6017 * 6018 * Returns 0 on success, negative on failure 6019 **/ 6020 static int e1000_change_mtu(struct net_device *netdev, int new_mtu) 6021 { 6022 struct e1000_adapter *adapter = netdev_priv(netdev); 6023 int max_frame = new_mtu + VLAN_ETH_HLEN + ETH_FCS_LEN; 6024 6025 /* Jumbo frame support */ 6026 if ((new_mtu > ETH_DATA_LEN) && 6027 !(adapter->flags & FLAG_HAS_JUMBO_FRAMES)) { 6028 e_err("Jumbo Frames not supported.\n"); 6029 return -EINVAL; 6030 } 6031 6032 /* Jumbo frame workaround on 82579 and newer requires CRC be stripped */ 6033 if ((adapter->hw.mac.type >= e1000_pch2lan) && 6034 !(adapter->flags2 & FLAG2_CRC_STRIPPING) && 6035 (new_mtu > ETH_DATA_LEN)) { 6036 e_err("Jumbo Frames not supported on this device when CRC stripping is disabled.\n"); 6037 return -EINVAL; 6038 } 6039 6040 while (test_and_set_bit(__E1000_RESETTING, &adapter->state)) 6041 usleep_range(1000, 1100); 6042 /* e1000e_down -> e1000e_reset dependent on max_frame_size & mtu */ 6043 adapter->max_frame_size = max_frame; 6044 netdev_dbg(netdev, "changing MTU from %d to %d\n", 6045 netdev->mtu, new_mtu); 6046 netdev->mtu = new_mtu; 6047 6048 pm_runtime_get_sync(netdev->dev.parent); 6049 6050 if (netif_running(netdev)) 6051 e1000e_down(adapter, true); 6052 6053 /* NOTE: netdev_alloc_skb reserves 16 bytes, and typically NET_IP_ALIGN 6054 * means we reserve 2 more, this pushes us to allocate from the next 6055 * larger slab size. 6056 * i.e. RXBUFFER_2048 --> size-4096 slab 6057 * However with the new *_jumbo_rx* routines, jumbo receives will use 6058 * fragmented skbs 6059 */ 6060 6061 if (max_frame <= 2048) 6062 adapter->rx_buffer_len = 2048; 6063 else 6064 adapter->rx_buffer_len = 4096; 6065 6066 /* adjust allocation if LPE protects us, and we aren't using SBP */ 6067 if (max_frame <= (VLAN_ETH_FRAME_LEN + ETH_FCS_LEN)) 6068 adapter->rx_buffer_len = VLAN_ETH_FRAME_LEN + ETH_FCS_LEN; 6069 6070 if (netif_running(netdev)) 6071 e1000e_up(adapter); 6072 else 6073 e1000e_reset(adapter); 6074 6075 pm_runtime_put_sync(netdev->dev.parent); 6076 6077 clear_bit(__E1000_RESETTING, &adapter->state); 6078 6079 return 0; 6080 } 6081 6082 static int e1000_mii_ioctl(struct net_device *netdev, struct ifreq *ifr, 6083 int cmd) 6084 { 6085 struct e1000_adapter *adapter = netdev_priv(netdev); 6086 struct mii_ioctl_data *data = if_mii(ifr); 6087 6088 if (adapter->hw.phy.media_type != e1000_media_type_copper) 6089 return -EOPNOTSUPP; 6090 6091 switch (cmd) { 6092 case SIOCGMIIPHY: 6093 data->phy_id = adapter->hw.phy.addr; 6094 break; 6095 case SIOCGMIIREG: 6096 e1000_phy_read_status(adapter); 6097 6098 switch (data->reg_num & 0x1F) { 6099 case MII_BMCR: 6100 data->val_out = adapter->phy_regs.bmcr; 6101 break; 6102 case MII_BMSR: 6103 data->val_out = adapter->phy_regs.bmsr; 6104 break; 6105 case MII_PHYSID1: 6106 data->val_out = (adapter->hw.phy.id >> 16); 6107 break; 6108 case MII_PHYSID2: 6109 data->val_out = (adapter->hw.phy.id & 0xFFFF); 6110 break; 6111 case MII_ADVERTISE: 6112 data->val_out = adapter->phy_regs.advertise; 6113 break; 6114 case MII_LPA: 6115 data->val_out = adapter->phy_regs.lpa; 6116 break; 6117 case MII_EXPANSION: 6118 data->val_out = adapter->phy_regs.expansion; 6119 break; 6120 case MII_CTRL1000: 6121 data->val_out = adapter->phy_regs.ctrl1000; 6122 break; 6123 case MII_STAT1000: 6124 data->val_out = adapter->phy_regs.stat1000; 6125 break; 6126 case MII_ESTATUS: 6127 data->val_out = adapter->phy_regs.estatus; 6128 break; 6129 default: 6130 return -EIO; 6131 } 6132 break; 6133 case SIOCSMIIREG: 6134 default: 6135 return -EOPNOTSUPP; 6136 } 6137 return 0; 6138 } 6139 6140 /** 6141 * e1000e_hwtstamp_ioctl - control hardware time stamping 6142 * @netdev: network interface device structure 6143 * @ifreq: interface request 6144 * 6145 * Outgoing time stamping can be enabled and disabled. Play nice and 6146 * disable it when requested, although it shouldn't cause any overhead 6147 * when no packet needs it. At most one packet in the queue may be 6148 * marked for time stamping, otherwise it would be impossible to tell 6149 * for sure to which packet the hardware time stamp belongs. 6150 * 6151 * Incoming time stamping has to be configured via the hardware filters. 6152 * Not all combinations are supported, in particular event type has to be 6153 * specified. Matching the kind of event packet is not supported, with the 6154 * exception of "all V2 events regardless of level 2 or 4". 6155 **/ 6156 static int e1000e_hwtstamp_set(struct net_device *netdev, struct ifreq *ifr) 6157 { 6158 struct e1000_adapter *adapter = netdev_priv(netdev); 6159 struct hwtstamp_config config; 6160 int ret_val; 6161 6162 if (copy_from_user(&config, ifr->ifr_data, sizeof(config))) 6163 return -EFAULT; 6164 6165 ret_val = e1000e_config_hwtstamp(adapter, &config); 6166 if (ret_val) 6167 return ret_val; 6168 6169 switch (config.rx_filter) { 6170 case HWTSTAMP_FILTER_PTP_V2_L4_SYNC: 6171 case HWTSTAMP_FILTER_PTP_V2_L2_SYNC: 6172 case HWTSTAMP_FILTER_PTP_V2_SYNC: 6173 case HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ: 6174 case HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ: 6175 case HWTSTAMP_FILTER_PTP_V2_DELAY_REQ: 6176 /* With V2 type filters which specify a Sync or Delay Request, 6177 * Path Delay Request/Response messages are also time stamped 6178 * by hardware so notify the caller the requested packets plus 6179 * some others are time stamped. 6180 */ 6181 config.rx_filter = HWTSTAMP_FILTER_SOME; 6182 break; 6183 default: 6184 break; 6185 } 6186 6187 return copy_to_user(ifr->ifr_data, &config, 6188 sizeof(config)) ? -EFAULT : 0; 6189 } 6190 6191 static int e1000e_hwtstamp_get(struct net_device *netdev, struct ifreq *ifr) 6192 { 6193 struct e1000_adapter *adapter = netdev_priv(netdev); 6194 6195 return copy_to_user(ifr->ifr_data, &adapter->hwtstamp_config, 6196 sizeof(adapter->hwtstamp_config)) ? -EFAULT : 0; 6197 } 6198 6199 static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd) 6200 { 6201 switch (cmd) { 6202 case SIOCGMIIPHY: 6203 case SIOCGMIIREG: 6204 case SIOCSMIIREG: 6205 return e1000_mii_ioctl(netdev, ifr, cmd); 6206 case SIOCSHWTSTAMP: 6207 return e1000e_hwtstamp_set(netdev, ifr); 6208 case SIOCGHWTSTAMP: 6209 return e1000e_hwtstamp_get(netdev, ifr); 6210 default: 6211 return -EOPNOTSUPP; 6212 } 6213 } 6214 6215 static int e1000_init_phy_wakeup(struct e1000_adapter *adapter, u32 wufc) 6216 { 6217 struct e1000_hw *hw = &adapter->hw; 6218 u32 i, mac_reg, wuc; 6219 u16 phy_reg, wuc_enable; 6220 int retval; 6221 6222 /* copy MAC RARs to PHY RARs */ 6223 e1000_copy_rx_addrs_to_phy_ich8lan(hw); 6224 6225 retval = hw->phy.ops.acquire(hw); 6226 if (retval) { 6227 e_err("Could not acquire PHY\n"); 6228 return retval; 6229 } 6230 6231 /* Enable access to wakeup registers on and set page to BM_WUC_PAGE */ 6232 retval = e1000_enable_phy_wakeup_reg_access_bm(hw, &wuc_enable); 6233 if (retval) 6234 goto release; 6235 6236 /* copy MAC MTA to PHY MTA - only needed for pchlan */ 6237 for (i = 0; i < adapter->hw.mac.mta_reg_count; i++) { 6238 mac_reg = E1000_READ_REG_ARRAY(hw, E1000_MTA, i); 6239 hw->phy.ops.write_reg_page(hw, BM_MTA(i), 6240 (u16)(mac_reg & 0xFFFF)); 6241 hw->phy.ops.write_reg_page(hw, BM_MTA(i) + 1, 6242 (u16)((mac_reg >> 16) & 0xFFFF)); 6243 } 6244 6245 /* configure PHY Rx Control register */ 6246 hw->phy.ops.read_reg_page(&adapter->hw, BM_RCTL, &phy_reg); 6247 mac_reg = er32(RCTL); 6248 if (mac_reg & E1000_RCTL_UPE) 6249 phy_reg |= BM_RCTL_UPE; 6250 if (mac_reg & E1000_RCTL_MPE) 6251 phy_reg |= BM_RCTL_MPE; 6252 phy_reg &= ~(BM_RCTL_MO_MASK); 6253 if (mac_reg & E1000_RCTL_MO_3) 6254 phy_reg |= (((mac_reg & E1000_RCTL_MO_3) >> E1000_RCTL_MO_SHIFT) 6255 << BM_RCTL_MO_SHIFT); 6256 if (mac_reg & E1000_RCTL_BAM) 6257 phy_reg |= BM_RCTL_BAM; 6258 if (mac_reg & E1000_RCTL_PMCF) 6259 phy_reg |= BM_RCTL_PMCF; 6260 mac_reg = er32(CTRL); 6261 if (mac_reg & E1000_CTRL_RFCE) 6262 phy_reg |= BM_RCTL_RFCE; 6263 hw->phy.ops.write_reg_page(&adapter->hw, BM_RCTL, phy_reg); 6264 6265 wuc = E1000_WUC_PME_EN; 6266 if (wufc & (E1000_WUFC_MAG | E1000_WUFC_LNKC)) 6267 wuc |= E1000_WUC_APME; 6268 6269 /* enable PHY wakeup in MAC register */ 6270 ew32(WUFC, wufc); 6271 ew32(WUC, (E1000_WUC_PHY_WAKE | E1000_WUC_APMPME | 6272 E1000_WUC_PME_STATUS | wuc)); 6273 6274 /* configure and enable PHY wakeup in PHY registers */ 6275 hw->phy.ops.write_reg_page(&adapter->hw, BM_WUFC, wufc); 6276 hw->phy.ops.write_reg_page(&adapter->hw, BM_WUC, wuc); 6277 6278 /* activate PHY wakeup */ 6279 wuc_enable |= BM_WUC_ENABLE_BIT | BM_WUC_HOST_WU_BIT; 6280 retval = e1000_disable_phy_wakeup_reg_access_bm(hw, &wuc_enable); 6281 if (retval) 6282 e_err("Could not set PHY Host Wakeup bit\n"); 6283 release: 6284 hw->phy.ops.release(hw); 6285 6286 return retval; 6287 } 6288 6289 static void e1000e_flush_lpic(struct pci_dev *pdev) 6290 { 6291 struct net_device *netdev = pci_get_drvdata(pdev); 6292 struct e1000_adapter *adapter = netdev_priv(netdev); 6293 struct e1000_hw *hw = &adapter->hw; 6294 u32 ret_val; 6295 6296 pm_runtime_get_sync(netdev->dev.parent); 6297 6298 ret_val = hw->phy.ops.acquire(hw); 6299 if (ret_val) 6300 goto fl_out; 6301 6302 pr_info("EEE TX LPI TIMER: %08X\n", 6303 er32(LPIC) >> E1000_LPIC_LPIET_SHIFT); 6304 6305 hw->phy.ops.release(hw); 6306 6307 fl_out: 6308 pm_runtime_put_sync(netdev->dev.parent); 6309 } 6310 6311 #ifdef CONFIG_PM_SLEEP 6312 /* S0ix implementation */ 6313 static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter) 6314 { 6315 struct e1000_hw *hw = &adapter->hw; 6316 u32 mac_data; 6317 u16 phy_data; 6318 6319 /* Disable the periodic inband message, 6320 * don't request PCIe clock in K1 page770_17[10:9] = 10b 6321 */ 6322 e1e_rphy(hw, HV_PM_CTRL, &phy_data); 6323 phy_data &= ~HV_PM_CTRL_K1_CLK_REQ; 6324 phy_data |= BIT(10); 6325 e1e_wphy(hw, HV_PM_CTRL, phy_data); 6326 6327 /* Make sure we don't exit K1 every time a new packet arrives 6328 * 772_29[5] = 1 CS_Mode_Stay_In_K1 6329 */ 6330 e1e_rphy(hw, I217_CGFREG, &phy_data); 6331 phy_data |= BIT(5); 6332 e1e_wphy(hw, I217_CGFREG, phy_data); 6333 6334 /* Change the MAC/PHY interface to SMBus 6335 * Force the SMBus in PHY page769_23[0] = 1 6336 * Force the SMBus in MAC CTRL_EXT[11] = 1 6337 */ 6338 e1e_rphy(hw, CV_SMB_CTRL, &phy_data); 6339 phy_data |= CV_SMB_CTRL_FORCE_SMBUS; 6340 e1e_wphy(hw, CV_SMB_CTRL, phy_data); 6341 mac_data = er32(CTRL_EXT); 6342 mac_data |= E1000_CTRL_EXT_FORCE_SMBUS; 6343 ew32(CTRL_EXT, mac_data); 6344 6345 /* DFT control: PHY bit: page769_20[0] = 1 6346 * Gate PPW via EXTCNF_CTRL - set 0x0F00[7] = 1 6347 */ 6348 e1e_rphy(hw, I82579_DFT_CTRL, &phy_data); 6349 phy_data |= BIT(0); 6350 e1e_wphy(hw, I82579_DFT_CTRL, phy_data); 6351 6352 mac_data = er32(EXTCNF_CTRL); 6353 mac_data |= E1000_EXTCNF_CTRL_GATE_PHY_CFG; 6354 ew32(EXTCNF_CTRL, mac_data); 6355 6356 /* Check MAC Tx/Rx packet buffer pointers. 6357 * Reset MAC Tx/Rx packet buffer pointers to suppress any 6358 * pending traffic indication that would prevent power gating. 6359 */ 6360 mac_data = er32(TDFH); 6361 if (mac_data) 6362 ew32(TDFH, 0); 6363 mac_data = er32(TDFT); 6364 if (mac_data) 6365 ew32(TDFT, 0); 6366 mac_data = er32(TDFHS); 6367 if (mac_data) 6368 ew32(TDFHS, 0); 6369 mac_data = er32(TDFTS); 6370 if (mac_data) 6371 ew32(TDFTS, 0); 6372 mac_data = er32(TDFPC); 6373 if (mac_data) 6374 ew32(TDFPC, 0); 6375 mac_data = er32(RDFH); 6376 if (mac_data) 6377 ew32(RDFH, 0); 6378 mac_data = er32(RDFT); 6379 if (mac_data) 6380 ew32(RDFT, 0); 6381 mac_data = er32(RDFHS); 6382 if (mac_data) 6383 ew32(RDFHS, 0); 6384 mac_data = er32(RDFTS); 6385 if (mac_data) 6386 ew32(RDFTS, 0); 6387 mac_data = er32(RDFPC); 6388 if (mac_data) 6389 ew32(RDFPC, 0); 6390 6391 /* Enable the Dynamic Power Gating in the MAC */ 6392 mac_data = er32(FEXTNVM7); 6393 mac_data |= BIT(22); 6394 ew32(FEXTNVM7, mac_data); 6395 6396 /* Disable the time synchronization clock */ 6397 mac_data = er32(FEXTNVM7); 6398 mac_data |= BIT(31); 6399 mac_data &= ~BIT(0); 6400 ew32(FEXTNVM7, mac_data); 6401 6402 /* Dynamic Power Gating Enable */ 6403 mac_data = er32(CTRL_EXT); 6404 mac_data |= BIT(3); 6405 ew32(CTRL_EXT, mac_data); 6406 6407 /* Enable the Dynamic Clock Gating in the DMA and MAC */ 6408 mac_data = er32(CTRL_EXT); 6409 mac_data |= E1000_CTRL_EXT_DMA_DYN_CLK_EN; 6410 ew32(CTRL_EXT, mac_data); 6411 6412 /* No MAC DPG gating SLP_S0 in modern standby 6413 * Switch the logic of the lanphypc to use PMC counter 6414 */ 6415 mac_data = er32(FEXTNVM5); 6416 mac_data |= BIT(7); 6417 ew32(FEXTNVM5, mac_data); 6418 } 6419 6420 static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter) 6421 { 6422 struct e1000_hw *hw = &adapter->hw; 6423 u32 mac_data; 6424 u16 phy_data; 6425 6426 /* Disable the Dynamic Power Gating in the MAC */ 6427 mac_data = er32(FEXTNVM7); 6428 mac_data &= 0xFFBFFFFF; 6429 ew32(FEXTNVM7, mac_data); 6430 6431 /* Enable the time synchronization clock */ 6432 mac_data = er32(FEXTNVM7); 6433 mac_data |= BIT(0); 6434 ew32(FEXTNVM7, mac_data); 6435 6436 /* Disable Dynamic Power Gating */ 6437 mac_data = er32(CTRL_EXT); 6438 mac_data &= 0xFFFFFFF7; 6439 ew32(CTRL_EXT, mac_data); 6440 6441 /* Disable the Dynamic Clock Gating in the DMA and MAC */ 6442 mac_data = er32(CTRL_EXT); 6443 mac_data &= 0xFFF7FFFF; 6444 ew32(CTRL_EXT, mac_data); 6445 6446 /* Revert the lanphypc logic to use the internal Gbe counter 6447 * and not the PMC counter 6448 */ 6449 mac_data = er32(FEXTNVM5); 6450 mac_data &= 0xFFFFFF7F; 6451 ew32(FEXTNVM5, mac_data); 6452 6453 /* Enable the periodic inband message, 6454 * Request PCIe clock in K1 page770_17[10:9] =01b 6455 */ 6456 e1e_rphy(hw, HV_PM_CTRL, &phy_data); 6457 phy_data &= 0xFBFF; 6458 phy_data |= HV_PM_CTRL_K1_CLK_REQ; 6459 e1e_wphy(hw, HV_PM_CTRL, phy_data); 6460 6461 /* Return back configuration 6462 * 772_29[5] = 0 CS_Mode_Stay_In_K1 6463 */ 6464 e1e_rphy(hw, I217_CGFREG, &phy_data); 6465 phy_data &= 0xFFDF; 6466 e1e_wphy(hw, I217_CGFREG, phy_data); 6467 6468 /* Change the MAC/PHY interface to Kumeran 6469 * Unforce the SMBus in PHY page769_23[0] = 0 6470 * Unforce the SMBus in MAC CTRL_EXT[11] = 0 6471 */ 6472 e1e_rphy(hw, CV_SMB_CTRL, &phy_data); 6473 phy_data &= ~CV_SMB_CTRL_FORCE_SMBUS; 6474 e1e_wphy(hw, CV_SMB_CTRL, phy_data); 6475 mac_data = er32(CTRL_EXT); 6476 mac_data &= ~E1000_CTRL_EXT_FORCE_SMBUS; 6477 ew32(CTRL_EXT, mac_data); 6478 } 6479 #endif /* CONFIG_PM_SLEEP */ 6480 6481 static int e1000e_pm_freeze(struct device *dev) 6482 { 6483 struct net_device *netdev = dev_get_drvdata(dev); 6484 struct e1000_adapter *adapter = netdev_priv(netdev); 6485 bool present; 6486 6487 rtnl_lock(); 6488 6489 present = netif_device_present(netdev); 6490 netif_device_detach(netdev); 6491 6492 if (present && netif_running(netdev)) { 6493 int count = E1000_CHECK_RESET_COUNT; 6494 6495 while (test_bit(__E1000_RESETTING, &adapter->state) && count--) 6496 usleep_range(10000, 11000); 6497 6498 WARN_ON(test_bit(__E1000_RESETTING, &adapter->state)); 6499 6500 /* Quiesce the device without resetting the hardware */ 6501 e1000e_down(adapter, false); 6502 e1000_free_irq(adapter); 6503 } 6504 rtnl_unlock(); 6505 6506 e1000e_reset_interrupt_capability(adapter); 6507 6508 /* Allow time for pending master requests to run */ 6509 e1000e_disable_pcie_master(&adapter->hw); 6510 6511 return 0; 6512 } 6513 6514 static int __e1000_shutdown(struct pci_dev *pdev, bool runtime) 6515 { 6516 struct net_device *netdev = pci_get_drvdata(pdev); 6517 struct e1000_adapter *adapter = netdev_priv(netdev); 6518 struct e1000_hw *hw = &adapter->hw; 6519 u32 ctrl, ctrl_ext, rctl, status; 6520 /* Runtime suspend should only enable wakeup for link changes */ 6521 u32 wufc = runtime ? E1000_WUFC_LNKC : adapter->wol; 6522 int retval = 0; 6523 6524 status = er32(STATUS); 6525 if (status & E1000_STATUS_LU) 6526 wufc &= ~E1000_WUFC_LNKC; 6527 6528 if (wufc) { 6529 e1000_setup_rctl(adapter); 6530 e1000e_set_rx_mode(netdev); 6531 6532 /* turn on all-multi mode if wake on multicast is enabled */ 6533 if (wufc & E1000_WUFC_MC) { 6534 rctl = er32(RCTL); 6535 rctl |= E1000_RCTL_MPE; 6536 ew32(RCTL, rctl); 6537 } 6538 6539 ctrl = er32(CTRL); 6540 ctrl |= E1000_CTRL_ADVD3WUC; 6541 if (!(adapter->flags2 & FLAG2_HAS_PHY_WAKEUP)) 6542 ctrl |= E1000_CTRL_EN_PHY_PWR_MGMT; 6543 ew32(CTRL, ctrl); 6544 6545 if (adapter->hw.phy.media_type == e1000_media_type_fiber || 6546 adapter->hw.phy.media_type == 6547 e1000_media_type_internal_serdes) { 6548 /* keep the laser running in D3 */ 6549 ctrl_ext = er32(CTRL_EXT); 6550 ctrl_ext |= E1000_CTRL_EXT_SDP3_DATA; 6551 ew32(CTRL_EXT, ctrl_ext); 6552 } 6553 6554 if (!runtime) 6555 e1000e_power_up_phy(adapter); 6556 6557 if (adapter->flags & FLAG_IS_ICH) 6558 e1000_suspend_workarounds_ich8lan(&adapter->hw); 6559 6560 if (adapter->flags2 & FLAG2_HAS_PHY_WAKEUP) { 6561 /* enable wakeup by the PHY */ 6562 retval = e1000_init_phy_wakeup(adapter, wufc); 6563 if (retval) 6564 return retval; 6565 } else { 6566 /* enable wakeup by the MAC */ 6567 ew32(WUFC, wufc); 6568 ew32(WUC, E1000_WUC_PME_EN); 6569 } 6570 } else { 6571 ew32(WUC, 0); 6572 ew32(WUFC, 0); 6573 6574 e1000_power_down_phy(adapter); 6575 } 6576 6577 if (adapter->hw.phy.type == e1000_phy_igp_3) { 6578 e1000e_igp3_phy_powerdown_workaround_ich8lan(&adapter->hw); 6579 } else if (hw->mac.type >= e1000_pch_lpt) { 6580 if (!(wufc & (E1000_WUFC_EX | E1000_WUFC_MC | E1000_WUFC_BC))) 6581 /* ULP does not support wake from unicast, multicast 6582 * or broadcast. 6583 */ 6584 retval = e1000_enable_ulp_lpt_lp(hw, !runtime); 6585 6586 if (retval) 6587 return retval; 6588 } 6589 6590 /* Ensure that the appropriate bits are set in LPI_CTRL 6591 * for EEE in Sx 6592 */ 6593 if ((hw->phy.type >= e1000_phy_i217) && 6594 adapter->eee_advert && hw->dev_spec.ich8lan.eee_lp_ability) { 6595 u16 lpi_ctrl = 0; 6596 6597 retval = hw->phy.ops.acquire(hw); 6598 if (!retval) { 6599 retval = e1e_rphy_locked(hw, I82579_LPI_CTRL, 6600 &lpi_ctrl); 6601 if (!retval) { 6602 if (adapter->eee_advert & 6603 hw->dev_spec.ich8lan.eee_lp_ability & 6604 I82579_EEE_100_SUPPORTED) 6605 lpi_ctrl |= I82579_LPI_CTRL_100_ENABLE; 6606 if (adapter->eee_advert & 6607 hw->dev_spec.ich8lan.eee_lp_ability & 6608 I82579_EEE_1000_SUPPORTED) 6609 lpi_ctrl |= I82579_LPI_CTRL_1000_ENABLE; 6610 6611 retval = e1e_wphy_locked(hw, I82579_LPI_CTRL, 6612 lpi_ctrl); 6613 } 6614 } 6615 hw->phy.ops.release(hw); 6616 } 6617 6618 /* Release control of h/w to f/w. If f/w is AMT enabled, this 6619 * would have already happened in close and is redundant. 6620 */ 6621 e1000e_release_hw_control(adapter); 6622 6623 pci_clear_master(pdev); 6624 6625 /* The pci-e switch on some quad port adapters will report a 6626 * correctable error when the MAC transitions from D0 to D3. To 6627 * prevent this we need to mask off the correctable errors on the 6628 * downstream port of the pci-e switch. 6629 * 6630 * We don't have the associated upstream bridge while assigning 6631 * the PCI device into guest. For example, the KVM on power is 6632 * one of the cases. 6633 */ 6634 if (adapter->flags & FLAG_IS_QUAD_PORT) { 6635 struct pci_dev *us_dev = pdev->bus->self; 6636 u16 devctl; 6637 6638 if (!us_dev) 6639 return 0; 6640 6641 pcie_capability_read_word(us_dev, PCI_EXP_DEVCTL, &devctl); 6642 pcie_capability_write_word(us_dev, PCI_EXP_DEVCTL, 6643 (devctl & ~PCI_EXP_DEVCTL_CERE)); 6644 6645 pci_save_state(pdev); 6646 pci_prepare_to_sleep(pdev); 6647 6648 pcie_capability_write_word(us_dev, PCI_EXP_DEVCTL, devctl); 6649 } 6650 6651 return 0; 6652 } 6653 6654 /** 6655 * __e1000e_disable_aspm - Disable ASPM states 6656 * @pdev: pointer to PCI device struct 6657 * @state: bit-mask of ASPM states to disable 6658 * @locked: indication if this context holds pci_bus_sem locked. 6659 * 6660 * Some devices *must* have certain ASPM states disabled per hardware errata. 6661 **/ 6662 static void __e1000e_disable_aspm(struct pci_dev *pdev, u16 state, int locked) 6663 { 6664 struct pci_dev *parent = pdev->bus->self; 6665 u16 aspm_dis_mask = 0; 6666 u16 pdev_aspmc, parent_aspmc; 6667 6668 switch (state) { 6669 case PCIE_LINK_STATE_L0S: 6670 case PCIE_LINK_STATE_L0S | PCIE_LINK_STATE_L1: 6671 aspm_dis_mask |= PCI_EXP_LNKCTL_ASPM_L0S; 6672 /* fall-through - can't have L1 without L0s */ 6673 case PCIE_LINK_STATE_L1: 6674 aspm_dis_mask |= PCI_EXP_LNKCTL_ASPM_L1; 6675 break; 6676 default: 6677 return; 6678 } 6679 6680 pcie_capability_read_word(pdev, PCI_EXP_LNKCTL, &pdev_aspmc); 6681 pdev_aspmc &= PCI_EXP_LNKCTL_ASPMC; 6682 6683 if (parent) { 6684 pcie_capability_read_word(parent, PCI_EXP_LNKCTL, 6685 &parent_aspmc); 6686 parent_aspmc &= PCI_EXP_LNKCTL_ASPMC; 6687 } 6688 6689 /* Nothing to do if the ASPM states to be disabled already are */ 6690 if (!(pdev_aspmc & aspm_dis_mask) && 6691 (!parent || !(parent_aspmc & aspm_dis_mask))) 6692 return; 6693 6694 dev_info(&pdev->dev, "Disabling ASPM %s %s\n", 6695 (aspm_dis_mask & pdev_aspmc & PCI_EXP_LNKCTL_ASPM_L0S) ? 6696 "L0s" : "", 6697 (aspm_dis_mask & pdev_aspmc & PCI_EXP_LNKCTL_ASPM_L1) ? 6698 "L1" : ""); 6699 6700 #ifdef CONFIG_PCIEASPM 6701 if (locked) 6702 pci_disable_link_state_locked(pdev, state); 6703 else 6704 pci_disable_link_state(pdev, state); 6705 6706 /* Double-check ASPM control. If not disabled by the above, the 6707 * BIOS is preventing that from happening (or CONFIG_PCIEASPM is 6708 * not enabled); override by writing PCI config space directly. 6709 */ 6710 pcie_capability_read_word(pdev, PCI_EXP_LNKCTL, &pdev_aspmc); 6711 pdev_aspmc &= PCI_EXP_LNKCTL_ASPMC; 6712 6713 if (!(aspm_dis_mask & pdev_aspmc)) 6714 return; 6715 #endif 6716 6717 /* Both device and parent should have the same ASPM setting. 6718 * Disable ASPM in downstream component first and then upstream. 6719 */ 6720 pcie_capability_clear_word(pdev, PCI_EXP_LNKCTL, aspm_dis_mask); 6721 6722 if (parent) 6723 pcie_capability_clear_word(parent, PCI_EXP_LNKCTL, 6724 aspm_dis_mask); 6725 } 6726 6727 /** 6728 * e1000e_disable_aspm - Disable ASPM states. 6729 * @pdev: pointer to PCI device struct 6730 * @state: bit-mask of ASPM states to disable 6731 * 6732 * This function acquires the pci_bus_sem! 6733 * Some devices *must* have certain ASPM states disabled per hardware errata. 6734 **/ 6735 static void e1000e_disable_aspm(struct pci_dev *pdev, u16 state) 6736 { 6737 __e1000e_disable_aspm(pdev, state, 0); 6738 } 6739 6740 /** 6741 * e1000e_disable_aspm_locked Disable ASPM states. 6742 * @pdev: pointer to PCI device struct 6743 * @state: bit-mask of ASPM states to disable 6744 * 6745 * This function must be called with pci_bus_sem acquired! 6746 * Some devices *must* have certain ASPM states disabled per hardware errata. 6747 **/ 6748 static void e1000e_disable_aspm_locked(struct pci_dev *pdev, u16 state) 6749 { 6750 __e1000e_disable_aspm(pdev, state, 1); 6751 } 6752 6753 static int e1000e_pm_thaw(struct device *dev) 6754 { 6755 struct net_device *netdev = dev_get_drvdata(dev); 6756 struct e1000_adapter *adapter = netdev_priv(netdev); 6757 int rc = 0; 6758 6759 e1000e_set_interrupt_capability(adapter); 6760 6761 rtnl_lock(); 6762 if (netif_running(netdev)) { 6763 rc = e1000_request_irq(adapter); 6764 if (rc) 6765 goto err_irq; 6766 6767 e1000e_up(adapter); 6768 } 6769 6770 netif_device_attach(netdev); 6771 err_irq: 6772 rtnl_unlock(); 6773 6774 return rc; 6775 } 6776 6777 #ifdef CONFIG_PM 6778 static int __e1000_resume(struct pci_dev *pdev) 6779 { 6780 struct net_device *netdev = pci_get_drvdata(pdev); 6781 struct e1000_adapter *adapter = netdev_priv(netdev); 6782 struct e1000_hw *hw = &adapter->hw; 6783 u16 aspm_disable_flag = 0; 6784 6785 if (adapter->flags2 & FLAG2_DISABLE_ASPM_L0S) 6786 aspm_disable_flag = PCIE_LINK_STATE_L0S; 6787 if (adapter->flags2 & FLAG2_DISABLE_ASPM_L1) 6788 aspm_disable_flag |= PCIE_LINK_STATE_L1; 6789 if (aspm_disable_flag) 6790 e1000e_disable_aspm(pdev, aspm_disable_flag); 6791 6792 pci_set_master(pdev); 6793 6794 if (hw->mac.type >= e1000_pch2lan) 6795 e1000_resume_workarounds_pchlan(&adapter->hw); 6796 6797 e1000e_power_up_phy(adapter); 6798 6799 /* report the system wakeup cause from S3/S4 */ 6800 if (adapter->flags2 & FLAG2_HAS_PHY_WAKEUP) { 6801 u16 phy_data; 6802 6803 e1e_rphy(&adapter->hw, BM_WUS, &phy_data); 6804 if (phy_data) { 6805 e_info("PHY Wakeup cause - %s\n", 6806 phy_data & E1000_WUS_EX ? "Unicast Packet" : 6807 phy_data & E1000_WUS_MC ? "Multicast Packet" : 6808 phy_data & E1000_WUS_BC ? "Broadcast Packet" : 6809 phy_data & E1000_WUS_MAG ? "Magic Packet" : 6810 phy_data & E1000_WUS_LNKC ? 6811 "Link Status Change" : "other"); 6812 } 6813 e1e_wphy(&adapter->hw, BM_WUS, ~0); 6814 } else { 6815 u32 wus = er32(WUS); 6816 6817 if (wus) { 6818 e_info("MAC Wakeup cause - %s\n", 6819 wus & E1000_WUS_EX ? "Unicast Packet" : 6820 wus & E1000_WUS_MC ? "Multicast Packet" : 6821 wus & E1000_WUS_BC ? "Broadcast Packet" : 6822 wus & E1000_WUS_MAG ? "Magic Packet" : 6823 wus & E1000_WUS_LNKC ? "Link Status Change" : 6824 "other"); 6825 } 6826 ew32(WUS, ~0); 6827 } 6828 6829 e1000e_reset(adapter); 6830 6831 e1000_init_manageability_pt(adapter); 6832 6833 /* If the controller has AMT, do not set DRV_LOAD until the interface 6834 * is up. For all other cases, let the f/w know that the h/w is now 6835 * under the control of the driver. 6836 */ 6837 if (!(adapter->flags & FLAG_HAS_AMT)) 6838 e1000e_get_hw_control(adapter); 6839 6840 return 0; 6841 } 6842 6843 #ifdef CONFIG_PM_SLEEP 6844 static int e1000e_pm_suspend(struct device *dev) 6845 { 6846 struct net_device *netdev = pci_get_drvdata(to_pci_dev(dev)); 6847 struct e1000_adapter *adapter = netdev_priv(netdev); 6848 struct pci_dev *pdev = to_pci_dev(dev); 6849 struct e1000_hw *hw = &adapter->hw; 6850 int rc; 6851 6852 e1000e_flush_lpic(pdev); 6853 6854 e1000e_pm_freeze(dev); 6855 6856 rc = __e1000_shutdown(pdev, false); 6857 if (rc) 6858 e1000e_pm_thaw(dev); 6859 6860 /* Introduce S0ix implementation */ 6861 if (hw->mac.type >= e1000_pch_cnp) 6862 e1000e_s0ix_entry_flow(adapter); 6863 6864 return rc; 6865 } 6866 6867 static int e1000e_pm_resume(struct device *dev) 6868 { 6869 struct net_device *netdev = pci_get_drvdata(to_pci_dev(dev)); 6870 struct e1000_adapter *adapter = netdev_priv(netdev); 6871 struct pci_dev *pdev = to_pci_dev(dev); 6872 struct e1000_hw *hw = &adapter->hw; 6873 int rc; 6874 6875 /* Introduce S0ix implementation */ 6876 if (hw->mac.type >= e1000_pch_cnp) 6877 e1000e_s0ix_exit_flow(adapter); 6878 6879 rc = __e1000_resume(pdev); 6880 if (rc) 6881 return rc; 6882 6883 return e1000e_pm_thaw(dev); 6884 } 6885 #endif /* CONFIG_PM_SLEEP */ 6886 6887 static int e1000e_pm_runtime_idle(struct device *dev) 6888 { 6889 struct net_device *netdev = dev_get_drvdata(dev); 6890 struct e1000_adapter *adapter = netdev_priv(netdev); 6891 u16 eee_lp; 6892 6893 eee_lp = adapter->hw.dev_spec.ich8lan.eee_lp_ability; 6894 6895 if (!e1000e_has_link(adapter)) { 6896 adapter->hw.dev_spec.ich8lan.eee_lp_ability = eee_lp; 6897 pm_schedule_suspend(dev, 5 * MSEC_PER_SEC); 6898 } 6899 6900 return -EBUSY; 6901 } 6902 6903 static int e1000e_pm_runtime_resume(struct device *dev) 6904 { 6905 struct pci_dev *pdev = to_pci_dev(dev); 6906 struct net_device *netdev = pci_get_drvdata(pdev); 6907 struct e1000_adapter *adapter = netdev_priv(netdev); 6908 int rc; 6909 6910 rc = __e1000_resume(pdev); 6911 if (rc) 6912 return rc; 6913 6914 if (netdev->flags & IFF_UP) 6915 e1000e_up(adapter); 6916 6917 return rc; 6918 } 6919 6920 static int e1000e_pm_runtime_suspend(struct device *dev) 6921 { 6922 struct pci_dev *pdev = to_pci_dev(dev); 6923 struct net_device *netdev = pci_get_drvdata(pdev); 6924 struct e1000_adapter *adapter = netdev_priv(netdev); 6925 6926 if (netdev->flags & IFF_UP) { 6927 int count = E1000_CHECK_RESET_COUNT; 6928 6929 while (test_bit(__E1000_RESETTING, &adapter->state) && count--) 6930 usleep_range(10000, 11000); 6931 6932 WARN_ON(test_bit(__E1000_RESETTING, &adapter->state)); 6933 6934 /* Down the device without resetting the hardware */ 6935 e1000e_down(adapter, false); 6936 } 6937 6938 if (__e1000_shutdown(pdev, true)) { 6939 e1000e_pm_runtime_resume(dev); 6940 return -EBUSY; 6941 } 6942 6943 return 0; 6944 } 6945 #endif /* CONFIG_PM */ 6946 6947 static void e1000_shutdown(struct pci_dev *pdev) 6948 { 6949 e1000e_flush_lpic(pdev); 6950 6951 e1000e_pm_freeze(&pdev->dev); 6952 6953 __e1000_shutdown(pdev, false); 6954 } 6955 6956 #ifdef CONFIG_NET_POLL_CONTROLLER 6957 6958 static irqreturn_t e1000_intr_msix(int __always_unused irq, void *data) 6959 { 6960 struct net_device *netdev = data; 6961 struct e1000_adapter *adapter = netdev_priv(netdev); 6962 6963 if (adapter->msix_entries) { 6964 int vector, msix_irq; 6965 6966 vector = 0; 6967 msix_irq = adapter->msix_entries[vector].vector; 6968 if (disable_hardirq(msix_irq)) 6969 e1000_intr_msix_rx(msix_irq, netdev); 6970 enable_irq(msix_irq); 6971 6972 vector++; 6973 msix_irq = adapter->msix_entries[vector].vector; 6974 if (disable_hardirq(msix_irq)) 6975 e1000_intr_msix_tx(msix_irq, netdev); 6976 enable_irq(msix_irq); 6977 6978 vector++; 6979 msix_irq = adapter->msix_entries[vector].vector; 6980 if (disable_hardirq(msix_irq)) 6981 e1000_msix_other(msix_irq, netdev); 6982 enable_irq(msix_irq); 6983 } 6984 6985 return IRQ_HANDLED; 6986 } 6987 6988 /** 6989 * e1000_netpoll 6990 * @netdev: network interface device structure 6991 * 6992 * Polling 'interrupt' - used by things like netconsole to send skbs 6993 * without having to re-enable interrupts. It's not called while 6994 * the interrupt routine is executing. 6995 */ 6996 static void e1000_netpoll(struct net_device *netdev) 6997 { 6998 struct e1000_adapter *adapter = netdev_priv(netdev); 6999 7000 switch (adapter->int_mode) { 7001 case E1000E_INT_MODE_MSIX: 7002 e1000_intr_msix(adapter->pdev->irq, netdev); 7003 break; 7004 case E1000E_INT_MODE_MSI: 7005 if (disable_hardirq(adapter->pdev->irq)) 7006 e1000_intr_msi(adapter->pdev->irq, netdev); 7007 enable_irq(adapter->pdev->irq); 7008 break; 7009 default: /* E1000E_INT_MODE_LEGACY */ 7010 if (disable_hardirq(adapter->pdev->irq)) 7011 e1000_intr(adapter->pdev->irq, netdev); 7012 enable_irq(adapter->pdev->irq); 7013 break; 7014 } 7015 } 7016 #endif 7017 7018 /** 7019 * e1000_io_error_detected - called when PCI error is detected 7020 * @pdev: Pointer to PCI device 7021 * @state: The current pci connection state 7022 * 7023 * This function is called after a PCI bus error affecting 7024 * this device has been detected. 7025 */ 7026 static pci_ers_result_t e1000_io_error_detected(struct pci_dev *pdev, 7027 pci_channel_state_t state) 7028 { 7029 e1000e_pm_freeze(&pdev->dev); 7030 7031 if (state == pci_channel_io_perm_failure) 7032 return PCI_ERS_RESULT_DISCONNECT; 7033 7034 pci_disable_device(pdev); 7035 7036 /* Request a slot slot reset. */ 7037 return PCI_ERS_RESULT_NEED_RESET; 7038 } 7039 7040 /** 7041 * e1000_io_slot_reset - called after the pci bus has been reset. 7042 * @pdev: Pointer to PCI device 7043 * 7044 * Restart the card from scratch, as if from a cold-boot. Implementation 7045 * resembles the first-half of the e1000e_pm_resume routine. 7046 */ 7047 static pci_ers_result_t e1000_io_slot_reset(struct pci_dev *pdev) 7048 { 7049 struct net_device *netdev = pci_get_drvdata(pdev); 7050 struct e1000_adapter *adapter = netdev_priv(netdev); 7051 struct e1000_hw *hw = &adapter->hw; 7052 u16 aspm_disable_flag = 0; 7053 int err; 7054 pci_ers_result_t result; 7055 7056 if (adapter->flags2 & FLAG2_DISABLE_ASPM_L0S) 7057 aspm_disable_flag = PCIE_LINK_STATE_L0S; 7058 if (adapter->flags2 & FLAG2_DISABLE_ASPM_L1) 7059 aspm_disable_flag |= PCIE_LINK_STATE_L1; 7060 if (aspm_disable_flag) 7061 e1000e_disable_aspm_locked(pdev, aspm_disable_flag); 7062 7063 err = pci_enable_device_mem(pdev); 7064 if (err) { 7065 dev_err(&pdev->dev, 7066 "Cannot re-enable PCI device after reset.\n"); 7067 result = PCI_ERS_RESULT_DISCONNECT; 7068 } else { 7069 pdev->state_saved = true; 7070 pci_restore_state(pdev); 7071 pci_set_master(pdev); 7072 7073 pci_enable_wake(pdev, PCI_D3hot, 0); 7074 pci_enable_wake(pdev, PCI_D3cold, 0); 7075 7076 e1000e_reset(adapter); 7077 ew32(WUS, ~0); 7078 result = PCI_ERS_RESULT_RECOVERED; 7079 } 7080 7081 return result; 7082 } 7083 7084 /** 7085 * e1000_io_resume - called when traffic can start flowing again. 7086 * @pdev: Pointer to PCI device 7087 * 7088 * This callback is called when the error recovery driver tells us that 7089 * its OK to resume normal operation. Implementation resembles the 7090 * second-half of the e1000e_pm_resume routine. 7091 */ 7092 static void e1000_io_resume(struct pci_dev *pdev) 7093 { 7094 struct net_device *netdev = pci_get_drvdata(pdev); 7095 struct e1000_adapter *adapter = netdev_priv(netdev); 7096 7097 e1000_init_manageability_pt(adapter); 7098 7099 e1000e_pm_thaw(&pdev->dev); 7100 7101 /* If the controller has AMT, do not set DRV_LOAD until the interface 7102 * is up. For all other cases, let the f/w know that the h/w is now 7103 * under the control of the driver. 7104 */ 7105 if (!(adapter->flags & FLAG_HAS_AMT)) 7106 e1000e_get_hw_control(adapter); 7107 } 7108 7109 static void e1000_print_device_info(struct e1000_adapter *adapter) 7110 { 7111 struct e1000_hw *hw = &adapter->hw; 7112 struct net_device *netdev = adapter->netdev; 7113 u32 ret_val; 7114 u8 pba_str[E1000_PBANUM_LENGTH]; 7115 7116 /* print bus type/speed/width info */ 7117 e_info("(PCI Express:2.5GT/s:%s) %pM\n", 7118 /* bus width */ 7119 ((hw->bus.width == e1000_bus_width_pcie_x4) ? "Width x4" : 7120 "Width x1"), 7121 /* MAC address */ 7122 netdev->dev_addr); 7123 e_info("Intel(R) PRO/%s Network Connection\n", 7124 (hw->phy.type == e1000_phy_ife) ? "10/100" : "1000"); 7125 ret_val = e1000_read_pba_string_generic(hw, pba_str, 7126 E1000_PBANUM_LENGTH); 7127 if (ret_val) 7128 strlcpy((char *)pba_str, "Unknown", sizeof(pba_str)); 7129 e_info("MAC: %d, PHY: %d, PBA No: %s\n", 7130 hw->mac.type, hw->phy.type, pba_str); 7131 } 7132 7133 static void e1000_eeprom_checks(struct e1000_adapter *adapter) 7134 { 7135 struct e1000_hw *hw = &adapter->hw; 7136 int ret_val; 7137 u16 buf = 0; 7138 7139 if (hw->mac.type != e1000_82573) 7140 return; 7141 7142 ret_val = e1000_read_nvm(hw, NVM_INIT_CONTROL2_REG, 1, &buf); 7143 le16_to_cpus(&buf); 7144 if (!ret_val && (!(buf & BIT(0)))) { 7145 /* Deep Smart Power Down (DSPD) */ 7146 dev_warn(&adapter->pdev->dev, 7147 "Warning: detected DSPD enabled in EEPROM\n"); 7148 } 7149 } 7150 7151 static netdev_features_t e1000_fix_features(struct net_device *netdev, 7152 netdev_features_t features) 7153 { 7154 struct e1000_adapter *adapter = netdev_priv(netdev); 7155 struct e1000_hw *hw = &adapter->hw; 7156 7157 /* Jumbo frame workaround on 82579 and newer requires CRC be stripped */ 7158 if ((hw->mac.type >= e1000_pch2lan) && (netdev->mtu > ETH_DATA_LEN)) 7159 features &= ~NETIF_F_RXFCS; 7160 7161 /* Since there is no support for separate Rx/Tx vlan accel 7162 * enable/disable make sure Tx flag is always in same state as Rx. 7163 */ 7164 if (features & NETIF_F_HW_VLAN_CTAG_RX) 7165 features |= NETIF_F_HW_VLAN_CTAG_TX; 7166 else 7167 features &= ~NETIF_F_HW_VLAN_CTAG_TX; 7168 7169 return features; 7170 } 7171 7172 static int e1000_set_features(struct net_device *netdev, 7173 netdev_features_t features) 7174 { 7175 struct e1000_adapter *adapter = netdev_priv(netdev); 7176 netdev_features_t changed = features ^ netdev->features; 7177 7178 if (changed & (NETIF_F_TSO | NETIF_F_TSO6)) 7179 adapter->flags |= FLAG_TSO_FORCE; 7180 7181 if (!(changed & (NETIF_F_HW_VLAN_CTAG_RX | NETIF_F_HW_VLAN_CTAG_TX | 7182 NETIF_F_RXCSUM | NETIF_F_RXHASH | NETIF_F_RXFCS | 7183 NETIF_F_RXALL))) 7184 return 0; 7185 7186 if (changed & NETIF_F_RXFCS) { 7187 if (features & NETIF_F_RXFCS) { 7188 adapter->flags2 &= ~FLAG2_CRC_STRIPPING; 7189 } else { 7190 /* We need to take it back to defaults, which might mean 7191 * stripping is still disabled at the adapter level. 7192 */ 7193 if (adapter->flags2 & FLAG2_DFLT_CRC_STRIPPING) 7194 adapter->flags2 |= FLAG2_CRC_STRIPPING; 7195 else 7196 adapter->flags2 &= ~FLAG2_CRC_STRIPPING; 7197 } 7198 } 7199 7200 netdev->features = features; 7201 7202 if (netif_running(netdev)) 7203 e1000e_reinit_locked(adapter); 7204 else 7205 e1000e_reset(adapter); 7206 7207 return 1; 7208 } 7209 7210 static const struct net_device_ops e1000e_netdev_ops = { 7211 .ndo_open = e1000e_open, 7212 .ndo_stop = e1000e_close, 7213 .ndo_start_xmit = e1000_xmit_frame, 7214 .ndo_get_stats64 = e1000e_get_stats64, 7215 .ndo_set_rx_mode = e1000e_set_rx_mode, 7216 .ndo_set_mac_address = e1000_set_mac, 7217 .ndo_change_mtu = e1000_change_mtu, 7218 .ndo_do_ioctl = e1000_ioctl, 7219 .ndo_tx_timeout = e1000_tx_timeout, 7220 .ndo_validate_addr = eth_validate_addr, 7221 7222 .ndo_vlan_rx_add_vid = e1000_vlan_rx_add_vid, 7223 .ndo_vlan_rx_kill_vid = e1000_vlan_rx_kill_vid, 7224 #ifdef CONFIG_NET_POLL_CONTROLLER 7225 .ndo_poll_controller = e1000_netpoll, 7226 #endif 7227 .ndo_set_features = e1000_set_features, 7228 .ndo_fix_features = e1000_fix_features, 7229 .ndo_features_check = passthru_features_check, 7230 }; 7231 7232 /** 7233 * e1000_probe - Device Initialization Routine 7234 * @pdev: PCI device information struct 7235 * @ent: entry in e1000_pci_tbl 7236 * 7237 * Returns 0 on success, negative on failure 7238 * 7239 * e1000_probe initializes an adapter identified by a pci_dev structure. 7240 * The OS initialization, configuring of the adapter private structure, 7241 * and a hardware reset occur. 7242 **/ 7243 static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent) 7244 { 7245 struct net_device *netdev; 7246 struct e1000_adapter *adapter; 7247 struct e1000_hw *hw; 7248 const struct e1000_info *ei = e1000_info_tbl[ent->driver_data]; 7249 resource_size_t mmio_start, mmio_len; 7250 resource_size_t flash_start, flash_len; 7251 static int cards_found; 7252 u16 aspm_disable_flag = 0; 7253 int bars, i, err, pci_using_dac; 7254 u16 eeprom_data = 0; 7255 u16 eeprom_apme_mask = E1000_EEPROM_APME; 7256 s32 ret_val = 0; 7257 7258 if (ei->flags2 & FLAG2_DISABLE_ASPM_L0S) 7259 aspm_disable_flag = PCIE_LINK_STATE_L0S; 7260 if (ei->flags2 & FLAG2_DISABLE_ASPM_L1) 7261 aspm_disable_flag |= PCIE_LINK_STATE_L1; 7262 if (aspm_disable_flag) 7263 e1000e_disable_aspm(pdev, aspm_disable_flag); 7264 7265 err = pci_enable_device_mem(pdev); 7266 if (err) 7267 return err; 7268 7269 pci_using_dac = 0; 7270 err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64)); 7271 if (!err) { 7272 pci_using_dac = 1; 7273 } else { 7274 err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32)); 7275 if (err) { 7276 dev_err(&pdev->dev, 7277 "No usable DMA configuration, aborting\n"); 7278 goto err_dma; 7279 } 7280 } 7281 7282 bars = pci_select_bars(pdev, IORESOURCE_MEM); 7283 err = pci_request_selected_regions_exclusive(pdev, bars, 7284 e1000e_driver_name); 7285 if (err) 7286 goto err_pci_reg; 7287 7288 /* AER (Advanced Error Reporting) hooks */ 7289 pci_enable_pcie_error_reporting(pdev); 7290 7291 pci_set_master(pdev); 7292 /* PCI config space info */ 7293 err = pci_save_state(pdev); 7294 if (err) 7295 goto err_alloc_etherdev; 7296 7297 err = -ENOMEM; 7298 netdev = alloc_etherdev(sizeof(struct e1000_adapter)); 7299 if (!netdev) 7300 goto err_alloc_etherdev; 7301 7302 SET_NETDEV_DEV(netdev, &pdev->dev); 7303 7304 netdev->irq = pdev->irq; 7305 7306 pci_set_drvdata(pdev, netdev); 7307 adapter = netdev_priv(netdev); 7308 hw = &adapter->hw; 7309 adapter->netdev = netdev; 7310 adapter->pdev = pdev; 7311 adapter->ei = ei; 7312 adapter->pba = ei->pba; 7313 adapter->flags = ei->flags; 7314 adapter->flags2 = ei->flags2; 7315 adapter->hw.adapter = adapter; 7316 adapter->hw.mac.type = ei->mac; 7317 adapter->max_hw_frame_size = ei->max_hw_frame_size; 7318 adapter->msg_enable = netif_msg_init(debug, DEFAULT_MSG_ENABLE); 7319 7320 mmio_start = pci_resource_start(pdev, 0); 7321 mmio_len = pci_resource_len(pdev, 0); 7322 7323 err = -EIO; 7324 adapter->hw.hw_addr = ioremap(mmio_start, mmio_len); 7325 if (!adapter->hw.hw_addr) 7326 goto err_ioremap; 7327 7328 if ((adapter->flags & FLAG_HAS_FLASH) && 7329 (pci_resource_flags(pdev, 1) & IORESOURCE_MEM) && 7330 (hw->mac.type < e1000_pch_spt)) { 7331 flash_start = pci_resource_start(pdev, 1); 7332 flash_len = pci_resource_len(pdev, 1); 7333 adapter->hw.flash_address = ioremap(flash_start, flash_len); 7334 if (!adapter->hw.flash_address) 7335 goto err_flashmap; 7336 } 7337 7338 /* Set default EEE advertisement */ 7339 if (adapter->flags2 & FLAG2_HAS_EEE) 7340 adapter->eee_advert = MDIO_EEE_100TX | MDIO_EEE_1000T; 7341 7342 /* construct the net_device struct */ 7343 netdev->netdev_ops = &e1000e_netdev_ops; 7344 e1000e_set_ethtool_ops(netdev); 7345 netdev->watchdog_timeo = 5 * HZ; 7346 netif_napi_add(netdev, &adapter->napi, e1000e_poll, 64); 7347 strlcpy(netdev->name, pci_name(pdev), sizeof(netdev->name)); 7348 7349 netdev->mem_start = mmio_start; 7350 netdev->mem_end = mmio_start + mmio_len; 7351 7352 adapter->bd_number = cards_found++; 7353 7354 e1000e_check_options(adapter); 7355 7356 /* setup adapter struct */ 7357 err = e1000_sw_init(adapter); 7358 if (err) 7359 goto err_sw_init; 7360 7361 memcpy(&hw->mac.ops, ei->mac_ops, sizeof(hw->mac.ops)); 7362 memcpy(&hw->nvm.ops, ei->nvm_ops, sizeof(hw->nvm.ops)); 7363 memcpy(&hw->phy.ops, ei->phy_ops, sizeof(hw->phy.ops)); 7364 7365 err = ei->get_variants(adapter); 7366 if (err) 7367 goto err_hw_init; 7368 7369 if ((adapter->flags & FLAG_IS_ICH) && 7370 (adapter->flags & FLAG_READ_ONLY_NVM) && 7371 (hw->mac.type < e1000_pch_spt)) 7372 e1000e_write_protect_nvm_ich8lan(&adapter->hw); 7373 7374 hw->mac.ops.get_bus_info(&adapter->hw); 7375 7376 adapter->hw.phy.autoneg_wait_to_complete = 0; 7377 7378 /* Copper options */ 7379 if (adapter->hw.phy.media_type == e1000_media_type_copper) { 7380 adapter->hw.phy.mdix = AUTO_ALL_MODES; 7381 adapter->hw.phy.disable_polarity_correction = 0; 7382 adapter->hw.phy.ms_type = e1000_ms_hw_default; 7383 } 7384 7385 if (hw->phy.ops.check_reset_block && hw->phy.ops.check_reset_block(hw)) 7386 dev_info(&pdev->dev, 7387 "PHY reset is blocked due to SOL/IDER session.\n"); 7388 7389 /* Set initial default active device features */ 7390 netdev->features = (NETIF_F_SG | 7391 NETIF_F_HW_VLAN_CTAG_RX | 7392 NETIF_F_HW_VLAN_CTAG_TX | 7393 NETIF_F_TSO | 7394 NETIF_F_TSO6 | 7395 NETIF_F_RXHASH | 7396 NETIF_F_RXCSUM | 7397 NETIF_F_HW_CSUM); 7398 7399 /* Set user-changeable features (subset of all device features) */ 7400 netdev->hw_features = netdev->features; 7401 netdev->hw_features |= NETIF_F_RXFCS; 7402 netdev->priv_flags |= IFF_SUPP_NOFCS; 7403 netdev->hw_features |= NETIF_F_RXALL; 7404 7405 if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) 7406 netdev->features |= NETIF_F_HW_VLAN_CTAG_FILTER; 7407 7408 netdev->vlan_features |= (NETIF_F_SG | 7409 NETIF_F_TSO | 7410 NETIF_F_TSO6 | 7411 NETIF_F_HW_CSUM); 7412 7413 netdev->priv_flags |= IFF_UNICAST_FLT; 7414 7415 if (pci_using_dac) { 7416 netdev->features |= NETIF_F_HIGHDMA; 7417 netdev->vlan_features |= NETIF_F_HIGHDMA; 7418 } 7419 7420 /* MTU range: 68 - max_hw_frame_size */ 7421 netdev->min_mtu = ETH_MIN_MTU; 7422 netdev->max_mtu = adapter->max_hw_frame_size - 7423 (VLAN_ETH_HLEN + ETH_FCS_LEN); 7424 7425 if (e1000e_enable_mng_pass_thru(&adapter->hw)) 7426 adapter->flags |= FLAG_MNG_PT_ENABLED; 7427 7428 /* before reading the NVM, reset the controller to 7429 * put the device in a known good starting state 7430 */ 7431 adapter->hw.mac.ops.reset_hw(&adapter->hw); 7432 7433 /* systems with ASPM and others may see the checksum fail on the first 7434 * attempt. Let's give it a few tries 7435 */ 7436 for (i = 0;; i++) { 7437 if (e1000_validate_nvm_checksum(&adapter->hw) >= 0) 7438 break; 7439 if (i == 2) { 7440 dev_err(&pdev->dev, "The NVM Checksum Is Not Valid\n"); 7441 err = -EIO; 7442 goto err_eeprom; 7443 } 7444 } 7445 7446 e1000_eeprom_checks(adapter); 7447 7448 /* copy the MAC address */ 7449 if (e1000e_read_mac_addr(&adapter->hw)) 7450 dev_err(&pdev->dev, 7451 "NVM Read Error while reading MAC address\n"); 7452 7453 memcpy(netdev->dev_addr, adapter->hw.mac.addr, netdev->addr_len); 7454 7455 if (!is_valid_ether_addr(netdev->dev_addr)) { 7456 dev_err(&pdev->dev, "Invalid MAC Address: %pM\n", 7457 netdev->dev_addr); 7458 err = -EIO; 7459 goto err_eeprom; 7460 } 7461 7462 timer_setup(&adapter->watchdog_timer, e1000_watchdog, 0); 7463 timer_setup(&adapter->phy_info_timer, e1000_update_phy_info, 0); 7464 7465 INIT_WORK(&adapter->reset_task, e1000_reset_task); 7466 INIT_WORK(&adapter->watchdog_task, e1000_watchdog_task); 7467 INIT_WORK(&adapter->downshift_task, e1000e_downshift_workaround); 7468 INIT_WORK(&adapter->update_phy_task, e1000e_update_phy_task); 7469 INIT_WORK(&adapter->print_hang_task, e1000_print_hw_hang); 7470 7471 /* Initialize link parameters. User can change them with ethtool */ 7472 adapter->hw.mac.autoneg = 1; 7473 adapter->fc_autoneg = true; 7474 adapter->hw.fc.requested_mode = e1000_fc_default; 7475 adapter->hw.fc.current_mode = e1000_fc_default; 7476 adapter->hw.phy.autoneg_advertised = 0x2f; 7477 7478 /* Initial Wake on LAN setting - If APM wake is enabled in 7479 * the EEPROM, enable the ACPI Magic Packet filter 7480 */ 7481 if (adapter->flags & FLAG_APME_IN_WUC) { 7482 /* APME bit in EEPROM is mapped to WUC.APME */ 7483 eeprom_data = er32(WUC); 7484 eeprom_apme_mask = E1000_WUC_APME; 7485 if ((hw->mac.type > e1000_ich10lan) && 7486 (eeprom_data & E1000_WUC_PHY_WAKE)) 7487 adapter->flags2 |= FLAG2_HAS_PHY_WAKEUP; 7488 } else if (adapter->flags & FLAG_APME_IN_CTRL3) { 7489 if (adapter->flags & FLAG_APME_CHECK_PORT_B && 7490 (adapter->hw.bus.func == 1)) 7491 ret_val = e1000_read_nvm(&adapter->hw, 7492 NVM_INIT_CONTROL3_PORT_B, 7493 1, &eeprom_data); 7494 else 7495 ret_val = e1000_read_nvm(&adapter->hw, 7496 NVM_INIT_CONTROL3_PORT_A, 7497 1, &eeprom_data); 7498 } 7499 7500 /* fetch WoL from EEPROM */ 7501 if (ret_val) 7502 e_dbg("NVM read error getting WoL initial values: %d\n", ret_val); 7503 else if (eeprom_data & eeprom_apme_mask) 7504 adapter->eeprom_wol |= E1000_WUFC_MAG; 7505 7506 /* now that we have the eeprom settings, apply the special cases 7507 * where the eeprom may be wrong or the board simply won't support 7508 * wake on lan on a particular port 7509 */ 7510 if (!(adapter->flags & FLAG_HAS_WOL)) 7511 adapter->eeprom_wol = 0; 7512 7513 /* initialize the wol settings based on the eeprom settings */ 7514 adapter->wol = adapter->eeprom_wol; 7515 7516 /* make sure adapter isn't asleep if manageability is enabled */ 7517 if (adapter->wol || (adapter->flags & FLAG_MNG_PT_ENABLED) || 7518 (hw->mac.ops.check_mng_mode(hw))) 7519 device_wakeup_enable(&pdev->dev); 7520 7521 /* save off EEPROM version number */ 7522 ret_val = e1000_read_nvm(&adapter->hw, 5, 1, &adapter->eeprom_vers); 7523 7524 if (ret_val) { 7525 e_dbg("NVM read error getting EEPROM version: %d\n", ret_val); 7526 adapter->eeprom_vers = 0; 7527 } 7528 7529 /* init PTP hardware clock */ 7530 e1000e_ptp_init(adapter); 7531 7532 /* reset the hardware with the new settings */ 7533 e1000e_reset(adapter); 7534 7535 /* If the controller has AMT, do not set DRV_LOAD until the interface 7536 * is up. For all other cases, let the f/w know that the h/w is now 7537 * under the control of the driver. 7538 */ 7539 if (!(adapter->flags & FLAG_HAS_AMT)) 7540 e1000e_get_hw_control(adapter); 7541 7542 strlcpy(netdev->name, "eth%d", sizeof(netdev->name)); 7543 err = register_netdev(netdev); 7544 if (err) 7545 goto err_register; 7546 7547 /* carrier off reporting is important to ethtool even BEFORE open */ 7548 netif_carrier_off(netdev); 7549 7550 e1000_print_device_info(adapter); 7551 7552 dev_pm_set_driver_flags(&pdev->dev, DPM_FLAG_NEVER_SKIP); 7553 7554 if (pci_dev_run_wake(pdev) && hw->mac.type < e1000_pch_cnp) 7555 pm_runtime_put_noidle(&pdev->dev); 7556 7557 return 0; 7558 7559 err_register: 7560 if (!(adapter->flags & FLAG_HAS_AMT)) 7561 e1000e_release_hw_control(adapter); 7562 err_eeprom: 7563 if (hw->phy.ops.check_reset_block && !hw->phy.ops.check_reset_block(hw)) 7564 e1000_phy_hw_reset(&adapter->hw); 7565 err_hw_init: 7566 kfree(adapter->tx_ring); 7567 kfree(adapter->rx_ring); 7568 err_sw_init: 7569 if ((adapter->hw.flash_address) && (hw->mac.type < e1000_pch_spt)) 7570 iounmap(adapter->hw.flash_address); 7571 e1000e_reset_interrupt_capability(adapter); 7572 err_flashmap: 7573 iounmap(adapter->hw.hw_addr); 7574 err_ioremap: 7575 free_netdev(netdev); 7576 err_alloc_etherdev: 7577 pci_release_mem_regions(pdev); 7578 err_pci_reg: 7579 err_dma: 7580 pci_disable_device(pdev); 7581 return err; 7582 } 7583 7584 /** 7585 * e1000_remove - Device Removal Routine 7586 * @pdev: PCI device information struct 7587 * 7588 * e1000_remove is called by the PCI subsystem to alert the driver 7589 * that it should release a PCI device. The could be caused by a 7590 * Hot-Plug event, or because the driver is going to be removed from 7591 * memory. 7592 **/ 7593 static void e1000_remove(struct pci_dev *pdev) 7594 { 7595 struct net_device *netdev = pci_get_drvdata(pdev); 7596 struct e1000_adapter *adapter = netdev_priv(netdev); 7597 7598 e1000e_ptp_remove(adapter); 7599 7600 /* The timers may be rescheduled, so explicitly disable them 7601 * from being rescheduled. 7602 */ 7603 set_bit(__E1000_DOWN, &adapter->state); 7604 del_timer_sync(&adapter->watchdog_timer); 7605 del_timer_sync(&adapter->phy_info_timer); 7606 7607 cancel_work_sync(&adapter->reset_task); 7608 cancel_work_sync(&adapter->watchdog_task); 7609 cancel_work_sync(&adapter->downshift_task); 7610 cancel_work_sync(&adapter->update_phy_task); 7611 cancel_work_sync(&adapter->print_hang_task); 7612 7613 if (adapter->flags & FLAG_HAS_HW_TIMESTAMP) { 7614 cancel_work_sync(&adapter->tx_hwtstamp_work); 7615 if (adapter->tx_hwtstamp_skb) { 7616 dev_consume_skb_any(adapter->tx_hwtstamp_skb); 7617 adapter->tx_hwtstamp_skb = NULL; 7618 } 7619 } 7620 7621 unregister_netdev(netdev); 7622 7623 if (pci_dev_run_wake(pdev)) 7624 pm_runtime_get_noresume(&pdev->dev); 7625 7626 /* Release control of h/w to f/w. If f/w is AMT enabled, this 7627 * would have already happened in close and is redundant. 7628 */ 7629 e1000e_release_hw_control(adapter); 7630 7631 e1000e_reset_interrupt_capability(adapter); 7632 kfree(adapter->tx_ring); 7633 kfree(adapter->rx_ring); 7634 7635 iounmap(adapter->hw.hw_addr); 7636 if ((adapter->hw.flash_address) && 7637 (adapter->hw.mac.type < e1000_pch_spt)) 7638 iounmap(adapter->hw.flash_address); 7639 pci_release_mem_regions(pdev); 7640 7641 free_netdev(netdev); 7642 7643 /* AER disable */ 7644 pci_disable_pcie_error_reporting(pdev); 7645 7646 pci_disable_device(pdev); 7647 } 7648 7649 /* PCI Error Recovery (ERS) */ 7650 static const struct pci_error_handlers e1000_err_handler = { 7651 .error_detected = e1000_io_error_detected, 7652 .slot_reset = e1000_io_slot_reset, 7653 .resume = e1000_io_resume, 7654 }; 7655 7656 static const struct pci_device_id e1000_pci_tbl[] = { 7657 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_COPPER), board_82571 }, 7658 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_FIBER), board_82571 }, 7659 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_QUAD_COPPER), board_82571 }, 7660 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_QUAD_COPPER_LP), 7661 board_82571 }, 7662 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_QUAD_FIBER), board_82571 }, 7663 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_SERDES), board_82571 }, 7664 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_SERDES_DUAL), board_82571 }, 7665 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_SERDES_QUAD), board_82571 }, 7666 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571PT_QUAD_COPPER), board_82571 }, 7667 7668 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI), board_82572 }, 7669 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI_COPPER), board_82572 }, 7670 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI_FIBER), board_82572 }, 7671 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI_SERDES), board_82572 }, 7672 7673 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82573E), board_82573 }, 7674 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82573E_IAMT), board_82573 }, 7675 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82573L), board_82573 }, 7676 7677 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82574L), board_82574 }, 7678 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82574LA), board_82574 }, 7679 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82583V), board_82583 }, 7680 7681 { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_COPPER_DPT), 7682 board_80003es2lan }, 7683 { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_COPPER_SPT), 7684 board_80003es2lan }, 7685 { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_SERDES_DPT), 7686 board_80003es2lan }, 7687 { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_SERDES_SPT), 7688 board_80003es2lan }, 7689 7690 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IFE), board_ich8lan }, 7691 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IFE_G), board_ich8lan }, 7692 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IFE_GT), board_ich8lan }, 7693 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_AMT), board_ich8lan }, 7694 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_C), board_ich8lan }, 7695 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_M), board_ich8lan }, 7696 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_M_AMT), board_ich8lan }, 7697 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_82567V_3), board_ich8lan }, 7698 7699 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IFE), board_ich9lan }, 7700 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IFE_G), board_ich9lan }, 7701 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IFE_GT), board_ich9lan }, 7702 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_AMT), board_ich9lan }, 7703 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_C), board_ich9lan }, 7704 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_BM), board_ich9lan }, 7705 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M), board_ich9lan }, 7706 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M_AMT), board_ich9lan }, 7707 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M_V), board_ich9lan }, 7708 7709 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_LM), board_ich9lan }, 7710 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_LF), board_ich9lan }, 7711 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_V), board_ich9lan }, 7712 7713 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_D_BM_LM), board_ich10lan }, 7714 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_D_BM_LF), board_ich10lan }, 7715 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_D_BM_V), board_ich10lan }, 7716 7717 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_M_HV_LM), board_pchlan }, 7718 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_M_HV_LC), board_pchlan }, 7719 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_D_HV_DM), board_pchlan }, 7720 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_D_HV_DC), board_pchlan }, 7721 7722 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH2_LV_LM), board_pch2lan }, 7723 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH2_LV_V), board_pch2lan }, 7724 7725 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LPT_I217_LM), board_pch_lpt }, 7726 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LPT_I217_V), board_pch_lpt }, 7727 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LPTLP_I218_LM), board_pch_lpt }, 7728 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LPTLP_I218_V), board_pch_lpt }, 7729 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_I218_LM2), board_pch_lpt }, 7730 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_I218_V2), board_pch_lpt }, 7731 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_I218_LM3), board_pch_lpt }, 7732 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_I218_V3), board_pch_lpt }, 7733 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_LM), board_pch_spt }, 7734 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_V), board_pch_spt }, 7735 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_LM2), board_pch_spt }, 7736 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_V2), board_pch_spt }, 7737 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LBG_I219_LM3), board_pch_spt }, 7738 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_LM4), board_pch_spt }, 7739 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_V4), board_pch_spt }, 7740 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_LM5), board_pch_spt }, 7741 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_V5), board_pch_spt }, 7742 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CNP_I219_LM6), board_pch_cnp }, 7743 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CNP_I219_V6), board_pch_cnp }, 7744 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CNP_I219_LM7), board_pch_cnp }, 7745 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CNP_I219_V7), board_pch_cnp }, 7746 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ICP_I219_LM8), board_pch_cnp }, 7747 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ICP_I219_V8), board_pch_cnp }, 7748 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ICP_I219_LM9), board_pch_cnp }, 7749 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ICP_I219_V9), board_pch_cnp }, 7750 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CMP_I219_LM10), board_pch_cnp }, 7751 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CMP_I219_V10), board_pch_cnp }, 7752 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CMP_I219_LM11), board_pch_cnp }, 7753 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CMP_I219_V11), board_pch_cnp }, 7754 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CMP_I219_LM12), board_pch_spt }, 7755 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CMP_I219_V12), board_pch_spt }, 7756 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_LM13), board_pch_cnp }, 7757 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_V13), board_pch_cnp }, 7758 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_LM14), board_pch_cnp }, 7759 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_V14), board_pch_cnp }, 7760 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_LM15), board_pch_cnp }, 7761 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_V15), board_pch_cnp }, 7762 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_LM16), board_pch_cnp }, 7763 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_V16), board_pch_cnp }, 7764 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_LM17), board_pch_cnp }, 7765 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_V17), board_pch_cnp }, 7766 7767 { 0, 0, 0, 0, 0, 0, 0 } /* terminate list */ 7768 }; 7769 MODULE_DEVICE_TABLE(pci, e1000_pci_tbl); 7770 7771 static const struct dev_pm_ops e1000_pm_ops = { 7772 #ifdef CONFIG_PM_SLEEP 7773 .suspend = e1000e_pm_suspend, 7774 .resume = e1000e_pm_resume, 7775 .freeze = e1000e_pm_freeze, 7776 .thaw = e1000e_pm_thaw, 7777 .poweroff = e1000e_pm_suspend, 7778 .restore = e1000e_pm_resume, 7779 #endif 7780 SET_RUNTIME_PM_OPS(e1000e_pm_runtime_suspend, e1000e_pm_runtime_resume, 7781 e1000e_pm_runtime_idle) 7782 }; 7783 7784 /* PCI Device API Driver */ 7785 static struct pci_driver e1000_driver = { 7786 .name = e1000e_driver_name, 7787 .id_table = e1000_pci_tbl, 7788 .probe = e1000_probe, 7789 .remove = e1000_remove, 7790 .driver = { 7791 .pm = &e1000_pm_ops, 7792 }, 7793 .shutdown = e1000_shutdown, 7794 .err_handler = &e1000_err_handler 7795 }; 7796 7797 /** 7798 * e1000_init_module - Driver Registration Routine 7799 * 7800 * e1000_init_module is the first routine called when the driver is 7801 * loaded. All it does is register with the PCI subsystem. 7802 **/ 7803 static int __init e1000_init_module(void) 7804 { 7805 pr_info("Intel(R) PRO/1000 Network Driver - %s\n", 7806 e1000e_driver_version); 7807 pr_info("Copyright(c) 1999 - 2015 Intel Corporation.\n"); 7808 7809 return pci_register_driver(&e1000_driver); 7810 } 7811 module_init(e1000_init_module); 7812 7813 /** 7814 * e1000_exit_module - Driver Exit Cleanup Routine 7815 * 7816 * e1000_exit_module is called just before the driver is removed 7817 * from memory. 7818 **/ 7819 static void __exit e1000_exit_module(void) 7820 { 7821 pci_unregister_driver(&e1000_driver); 7822 } 7823 module_exit(e1000_exit_module); 7824 7825 MODULE_AUTHOR("Intel Corporation, <linux.nics@intel.com>"); 7826 MODULE_DESCRIPTION("Intel(R) PRO/1000 Network Driver"); 7827 MODULE_LICENSE("GPL v2"); 7828 MODULE_VERSION(DRV_VERSION); 7829 7830 /* netdev.c */ 7831