1 // SPDX-License-Identifier: GPL-2.0 2 /* Copyright(c) 1999 - 2018 Intel Corporation. */ 3 4 /* 82571EB Gigabit Ethernet Controller 5 * 82571EB Gigabit Ethernet Controller (Copper) 6 * 82571EB Gigabit Ethernet Controller (Fiber) 7 * 82571EB Dual Port Gigabit Mezzanine Adapter 8 * 82571EB Quad Port Gigabit Mezzanine Adapter 9 * 82571PT Gigabit PT Quad Port Server ExpressModule 10 * 82572EI Gigabit Ethernet Controller (Copper) 11 * 82572EI Gigabit Ethernet Controller (Fiber) 12 * 82572EI Gigabit Ethernet Controller 13 * 82573V Gigabit Ethernet Controller (Copper) 14 * 82573E Gigabit Ethernet Controller (Copper) 15 * 82573L Gigabit Ethernet Controller 16 * 82574L Gigabit Network Connection 17 * 82583V Gigabit Network Connection 18 */ 19 20 #include "e1000.h" 21 22 static s32 e1000_get_phy_id_82571(struct e1000_hw *hw); 23 static s32 e1000_setup_copper_link_82571(struct e1000_hw *hw); 24 static s32 e1000_setup_fiber_serdes_link_82571(struct e1000_hw *hw); 25 static s32 e1000_check_for_serdes_link_82571(struct e1000_hw *hw); 26 static s32 e1000_write_nvm_eewr_82571(struct e1000_hw *hw, u16 offset, 27 u16 words, u16 *data); 28 static s32 e1000_fix_nvm_checksum_82571(struct e1000_hw *hw); 29 static void e1000_initialize_hw_bits_82571(struct e1000_hw *hw); 30 static void e1000_clear_hw_cntrs_82571(struct e1000_hw *hw); 31 static bool e1000_check_mng_mode_82574(struct e1000_hw *hw); 32 static s32 e1000_led_on_82574(struct e1000_hw *hw); 33 static void e1000_put_hw_semaphore_82571(struct e1000_hw *hw); 34 static void e1000_power_down_phy_copper_82571(struct e1000_hw *hw); 35 static void e1000_put_hw_semaphore_82573(struct e1000_hw *hw); 36 static s32 e1000_get_hw_semaphore_82574(struct e1000_hw *hw); 37 static void e1000_put_hw_semaphore_82574(struct e1000_hw *hw); 38 static s32 e1000_set_d0_lplu_state_82574(struct e1000_hw *hw, bool active); 39 static s32 e1000_set_d3_lplu_state_82574(struct e1000_hw *hw, bool active); 40 41 /** 42 * e1000_init_phy_params_82571 - Init PHY func ptrs. 43 * @hw: pointer to the HW structure 44 **/ 45 static s32 e1000_init_phy_params_82571(struct e1000_hw *hw) 46 { 47 struct e1000_phy_info *phy = &hw->phy; 48 s32 ret_val; 49 50 if (hw->phy.media_type != e1000_media_type_copper) { 51 phy->type = e1000_phy_none; 52 return 0; 53 } 54 55 phy->addr = 1; 56 phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; 57 phy->reset_delay_us = 100; 58 59 phy->ops.power_up = e1000_power_up_phy_copper; 60 phy->ops.power_down = e1000_power_down_phy_copper_82571; 61 62 switch (hw->mac.type) { 63 case e1000_82571: 64 case e1000_82572: 65 phy->type = e1000_phy_igp_2; 66 break; 67 case e1000_82573: 68 phy->type = e1000_phy_m88; 69 break; 70 case e1000_82574: 71 case e1000_82583: 72 phy->type = e1000_phy_bm; 73 phy->ops.acquire = e1000_get_hw_semaphore_82574; 74 phy->ops.release = e1000_put_hw_semaphore_82574; 75 phy->ops.set_d0_lplu_state = e1000_set_d0_lplu_state_82574; 76 phy->ops.set_d3_lplu_state = e1000_set_d3_lplu_state_82574; 77 break; 78 default: 79 return -E1000_ERR_PHY; 80 } 81 82 /* This can only be done after all function pointers are setup. */ 83 ret_val = e1000_get_phy_id_82571(hw); 84 if (ret_val) { 85 e_dbg("Error getting PHY ID\n"); 86 return ret_val; 87 } 88 89 /* Verify phy id */ 90 switch (hw->mac.type) { 91 case e1000_82571: 92 case e1000_82572: 93 if (phy->id != IGP01E1000_I_PHY_ID) 94 ret_val = -E1000_ERR_PHY; 95 break; 96 case e1000_82573: 97 if (phy->id != M88E1111_I_PHY_ID) 98 ret_val = -E1000_ERR_PHY; 99 break; 100 case e1000_82574: 101 case e1000_82583: 102 if (phy->id != BME1000_E_PHY_ID_R2) 103 ret_val = -E1000_ERR_PHY; 104 break; 105 default: 106 ret_val = -E1000_ERR_PHY; 107 break; 108 } 109 110 if (ret_val) 111 e_dbg("PHY ID unknown: type = 0x%08x\n", phy->id); 112 113 return ret_val; 114 } 115 116 /** 117 * e1000_init_nvm_params_82571 - Init NVM func ptrs. 118 * @hw: pointer to the HW structure 119 **/ 120 static s32 e1000_init_nvm_params_82571(struct e1000_hw *hw) 121 { 122 struct e1000_nvm_info *nvm = &hw->nvm; 123 u32 eecd = er32(EECD); 124 u16 size; 125 126 nvm->opcode_bits = 8; 127 nvm->delay_usec = 1; 128 switch (nvm->override) { 129 case e1000_nvm_override_spi_large: 130 nvm->page_size = 32; 131 nvm->address_bits = 16; 132 break; 133 case e1000_nvm_override_spi_small: 134 nvm->page_size = 8; 135 nvm->address_bits = 8; 136 break; 137 default: 138 nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8; 139 nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8; 140 break; 141 } 142 143 switch (hw->mac.type) { 144 case e1000_82573: 145 case e1000_82574: 146 case e1000_82583: 147 if (((eecd >> 15) & 0x3) == 0x3) { 148 nvm->type = e1000_nvm_flash_hw; 149 nvm->word_size = 2048; 150 /* Autonomous Flash update bit must be cleared due 151 * to Flash update issue. 152 */ 153 eecd &= ~E1000_EECD_AUPDEN; 154 ew32(EECD, eecd); 155 break; 156 } 157 /* Fall Through */ 158 default: 159 nvm->type = e1000_nvm_eeprom_spi; 160 size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >> 161 E1000_EECD_SIZE_EX_SHIFT); 162 /* Added to a constant, "size" becomes the left-shift value 163 * for setting word_size. 164 */ 165 size += NVM_WORD_SIZE_BASE_SHIFT; 166 167 /* EEPROM access above 16k is unsupported */ 168 if (size > 14) 169 size = 14; 170 nvm->word_size = BIT(size); 171 break; 172 } 173 174 /* Function Pointers */ 175 switch (hw->mac.type) { 176 case e1000_82574: 177 case e1000_82583: 178 nvm->ops.acquire = e1000_get_hw_semaphore_82574; 179 nvm->ops.release = e1000_put_hw_semaphore_82574; 180 break; 181 default: 182 break; 183 } 184 185 return 0; 186 } 187 188 /** 189 * e1000_init_mac_params_82571 - Init MAC func ptrs. 190 * @hw: pointer to the HW structure 191 **/ 192 static s32 e1000_init_mac_params_82571(struct e1000_hw *hw) 193 { 194 struct e1000_mac_info *mac = &hw->mac; 195 u32 swsm = 0; 196 u32 swsm2 = 0; 197 bool force_clear_smbi = false; 198 199 /* Set media type and media-dependent function pointers */ 200 switch (hw->adapter->pdev->device) { 201 case E1000_DEV_ID_82571EB_FIBER: 202 case E1000_DEV_ID_82572EI_FIBER: 203 case E1000_DEV_ID_82571EB_QUAD_FIBER: 204 hw->phy.media_type = e1000_media_type_fiber; 205 mac->ops.setup_physical_interface = 206 e1000_setup_fiber_serdes_link_82571; 207 mac->ops.check_for_link = e1000e_check_for_fiber_link; 208 mac->ops.get_link_up_info = 209 e1000e_get_speed_and_duplex_fiber_serdes; 210 break; 211 case E1000_DEV_ID_82571EB_SERDES: 212 case E1000_DEV_ID_82571EB_SERDES_DUAL: 213 case E1000_DEV_ID_82571EB_SERDES_QUAD: 214 case E1000_DEV_ID_82572EI_SERDES: 215 hw->phy.media_type = e1000_media_type_internal_serdes; 216 mac->ops.setup_physical_interface = 217 e1000_setup_fiber_serdes_link_82571; 218 mac->ops.check_for_link = e1000_check_for_serdes_link_82571; 219 mac->ops.get_link_up_info = 220 e1000e_get_speed_and_duplex_fiber_serdes; 221 break; 222 default: 223 hw->phy.media_type = e1000_media_type_copper; 224 mac->ops.setup_physical_interface = 225 e1000_setup_copper_link_82571; 226 mac->ops.check_for_link = e1000e_check_for_copper_link; 227 mac->ops.get_link_up_info = e1000e_get_speed_and_duplex_copper; 228 break; 229 } 230 231 /* Set mta register count */ 232 mac->mta_reg_count = 128; 233 /* Set rar entry count */ 234 mac->rar_entry_count = E1000_RAR_ENTRIES; 235 /* Adaptive IFS supported */ 236 mac->adaptive_ifs = true; 237 238 /* MAC-specific function pointers */ 239 switch (hw->mac.type) { 240 case e1000_82573: 241 mac->ops.set_lan_id = e1000_set_lan_id_single_port; 242 mac->ops.check_mng_mode = e1000e_check_mng_mode_generic; 243 mac->ops.led_on = e1000e_led_on_generic; 244 mac->ops.blink_led = e1000e_blink_led_generic; 245 246 /* FWSM register */ 247 mac->has_fwsm = true; 248 /* ARC supported; valid only if manageability features are 249 * enabled. 250 */ 251 mac->arc_subsystem_valid = !!(er32(FWSM) & 252 E1000_FWSM_MODE_MASK); 253 break; 254 case e1000_82574: 255 case e1000_82583: 256 mac->ops.set_lan_id = e1000_set_lan_id_single_port; 257 mac->ops.check_mng_mode = e1000_check_mng_mode_82574; 258 mac->ops.led_on = e1000_led_on_82574; 259 break; 260 default: 261 mac->ops.check_mng_mode = e1000e_check_mng_mode_generic; 262 mac->ops.led_on = e1000e_led_on_generic; 263 mac->ops.blink_led = e1000e_blink_led_generic; 264 265 /* FWSM register */ 266 mac->has_fwsm = true; 267 break; 268 } 269 270 /* Ensure that the inter-port SWSM.SMBI lock bit is clear before 271 * first NVM or PHY access. This should be done for single-port 272 * devices, and for one port only on dual-port devices so that 273 * for those devices we can still use the SMBI lock to synchronize 274 * inter-port accesses to the PHY & NVM. 275 */ 276 switch (hw->mac.type) { 277 case e1000_82571: 278 case e1000_82572: 279 swsm2 = er32(SWSM2); 280 281 if (!(swsm2 & E1000_SWSM2_LOCK)) { 282 /* Only do this for the first interface on this card */ 283 ew32(SWSM2, swsm2 | E1000_SWSM2_LOCK); 284 force_clear_smbi = true; 285 } else { 286 force_clear_smbi = false; 287 } 288 break; 289 default: 290 force_clear_smbi = true; 291 break; 292 } 293 294 if (force_clear_smbi) { 295 /* Make sure SWSM.SMBI is clear */ 296 swsm = er32(SWSM); 297 if (swsm & E1000_SWSM_SMBI) { 298 /* This bit should not be set on a first interface, and 299 * indicates that the bootagent or EFI code has 300 * improperly left this bit enabled 301 */ 302 e_dbg("Please update your 82571 Bootagent\n"); 303 } 304 ew32(SWSM, swsm & ~E1000_SWSM_SMBI); 305 } 306 307 /* Initialize device specific counter of SMBI acquisition timeouts. */ 308 hw->dev_spec.e82571.smb_counter = 0; 309 310 return 0; 311 } 312 313 static s32 e1000_get_variants_82571(struct e1000_adapter *adapter) 314 { 315 struct e1000_hw *hw = &adapter->hw; 316 static int global_quad_port_a; /* global port a indication */ 317 struct pci_dev *pdev = adapter->pdev; 318 int is_port_b = er32(STATUS) & E1000_STATUS_FUNC_1; 319 s32 rc; 320 321 rc = e1000_init_mac_params_82571(hw); 322 if (rc) 323 return rc; 324 325 rc = e1000_init_nvm_params_82571(hw); 326 if (rc) 327 return rc; 328 329 rc = e1000_init_phy_params_82571(hw); 330 if (rc) 331 return rc; 332 333 /* tag quad port adapters first, it's used below */ 334 switch (pdev->device) { 335 case E1000_DEV_ID_82571EB_QUAD_COPPER: 336 case E1000_DEV_ID_82571EB_QUAD_FIBER: 337 case E1000_DEV_ID_82571EB_QUAD_COPPER_LP: 338 case E1000_DEV_ID_82571PT_QUAD_COPPER: 339 adapter->flags |= FLAG_IS_QUAD_PORT; 340 /* mark the first port */ 341 if (global_quad_port_a == 0) 342 adapter->flags |= FLAG_IS_QUAD_PORT_A; 343 /* Reset for multiple quad port adapters */ 344 global_quad_port_a++; 345 if (global_quad_port_a == 4) 346 global_quad_port_a = 0; 347 break; 348 default: 349 break; 350 } 351 352 switch (adapter->hw.mac.type) { 353 case e1000_82571: 354 /* these dual ports don't have WoL on port B at all */ 355 if (((pdev->device == E1000_DEV_ID_82571EB_FIBER) || 356 (pdev->device == E1000_DEV_ID_82571EB_SERDES) || 357 (pdev->device == E1000_DEV_ID_82571EB_COPPER)) && 358 (is_port_b)) 359 adapter->flags &= ~FLAG_HAS_WOL; 360 /* quad ports only support WoL on port A */ 361 if (adapter->flags & FLAG_IS_QUAD_PORT && 362 (!(adapter->flags & FLAG_IS_QUAD_PORT_A))) 363 adapter->flags &= ~FLAG_HAS_WOL; 364 /* Does not support WoL on any port */ 365 if (pdev->device == E1000_DEV_ID_82571EB_SERDES_QUAD) 366 adapter->flags &= ~FLAG_HAS_WOL; 367 break; 368 case e1000_82573: 369 if (pdev->device == E1000_DEV_ID_82573L) { 370 adapter->flags |= FLAG_HAS_JUMBO_FRAMES; 371 adapter->max_hw_frame_size = DEFAULT_JUMBO; 372 } 373 break; 374 default: 375 break; 376 } 377 378 return 0; 379 } 380 381 /** 382 * e1000_get_phy_id_82571 - Retrieve the PHY ID and revision 383 * @hw: pointer to the HW structure 384 * 385 * Reads the PHY registers and stores the PHY ID and possibly the PHY 386 * revision in the hardware structure. 387 **/ 388 static s32 e1000_get_phy_id_82571(struct e1000_hw *hw) 389 { 390 struct e1000_phy_info *phy = &hw->phy; 391 s32 ret_val; 392 u16 phy_id = 0; 393 394 switch (hw->mac.type) { 395 case e1000_82571: 396 case e1000_82572: 397 /* The 82571 firmware may still be configuring the PHY. 398 * In this case, we cannot access the PHY until the 399 * configuration is done. So we explicitly set the 400 * PHY ID. 401 */ 402 phy->id = IGP01E1000_I_PHY_ID; 403 break; 404 case e1000_82573: 405 return e1000e_get_phy_id(hw); 406 case e1000_82574: 407 case e1000_82583: 408 ret_val = e1e_rphy(hw, MII_PHYSID1, &phy_id); 409 if (ret_val) 410 return ret_val; 411 412 phy->id = (u32)(phy_id << 16); 413 usleep_range(20, 40); 414 ret_val = e1e_rphy(hw, MII_PHYSID2, &phy_id); 415 if (ret_val) 416 return ret_val; 417 418 phy->id |= (u32)(phy_id); 419 phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK); 420 break; 421 default: 422 return -E1000_ERR_PHY; 423 } 424 425 return 0; 426 } 427 428 /** 429 * e1000_get_hw_semaphore_82571 - Acquire hardware semaphore 430 * @hw: pointer to the HW structure 431 * 432 * Acquire the HW semaphore to access the PHY or NVM 433 **/ 434 static s32 e1000_get_hw_semaphore_82571(struct e1000_hw *hw) 435 { 436 u32 swsm; 437 s32 sw_timeout = hw->nvm.word_size + 1; 438 s32 fw_timeout = hw->nvm.word_size + 1; 439 s32 i = 0; 440 441 /* If we have timedout 3 times on trying to acquire 442 * the inter-port SMBI semaphore, there is old code 443 * operating on the other port, and it is not 444 * releasing SMBI. Modify the number of times that 445 * we try for the semaphore to interwork with this 446 * older code. 447 */ 448 if (hw->dev_spec.e82571.smb_counter > 2) 449 sw_timeout = 1; 450 451 /* Get the SW semaphore */ 452 while (i < sw_timeout) { 453 swsm = er32(SWSM); 454 if (!(swsm & E1000_SWSM_SMBI)) 455 break; 456 457 usleep_range(50, 100); 458 i++; 459 } 460 461 if (i == sw_timeout) { 462 e_dbg("Driver can't access device - SMBI bit is set.\n"); 463 hw->dev_spec.e82571.smb_counter++; 464 } 465 /* Get the FW semaphore. */ 466 for (i = 0; i < fw_timeout; i++) { 467 swsm = er32(SWSM); 468 ew32(SWSM, swsm | E1000_SWSM_SWESMBI); 469 470 /* Semaphore acquired if bit latched */ 471 if (er32(SWSM) & E1000_SWSM_SWESMBI) 472 break; 473 474 usleep_range(50, 100); 475 } 476 477 if (i == fw_timeout) { 478 /* Release semaphores */ 479 e1000_put_hw_semaphore_82571(hw); 480 e_dbg("Driver can't access the NVM\n"); 481 return -E1000_ERR_NVM; 482 } 483 484 return 0; 485 } 486 487 /** 488 * e1000_put_hw_semaphore_82571 - Release hardware semaphore 489 * @hw: pointer to the HW structure 490 * 491 * Release hardware semaphore used to access the PHY or NVM 492 **/ 493 static void e1000_put_hw_semaphore_82571(struct e1000_hw *hw) 494 { 495 u32 swsm; 496 497 swsm = er32(SWSM); 498 swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI); 499 ew32(SWSM, swsm); 500 } 501 502 /** 503 * e1000_get_hw_semaphore_82573 - Acquire hardware semaphore 504 * @hw: pointer to the HW structure 505 * 506 * Acquire the HW semaphore during reset. 507 * 508 **/ 509 static s32 e1000_get_hw_semaphore_82573(struct e1000_hw *hw) 510 { 511 u32 extcnf_ctrl; 512 s32 i = 0; 513 514 extcnf_ctrl = er32(EXTCNF_CTRL); 515 do { 516 extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP; 517 ew32(EXTCNF_CTRL, extcnf_ctrl); 518 extcnf_ctrl = er32(EXTCNF_CTRL); 519 520 if (extcnf_ctrl & E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP) 521 break; 522 523 usleep_range(2000, 4000); 524 i++; 525 } while (i < MDIO_OWNERSHIP_TIMEOUT); 526 527 if (i == MDIO_OWNERSHIP_TIMEOUT) { 528 /* Release semaphores */ 529 e1000_put_hw_semaphore_82573(hw); 530 e_dbg("Driver can't access the PHY\n"); 531 return -E1000_ERR_PHY; 532 } 533 534 return 0; 535 } 536 537 /** 538 * e1000_put_hw_semaphore_82573 - Release hardware semaphore 539 * @hw: pointer to the HW structure 540 * 541 * Release hardware semaphore used during reset. 542 * 543 **/ 544 static void e1000_put_hw_semaphore_82573(struct e1000_hw *hw) 545 { 546 u32 extcnf_ctrl; 547 548 extcnf_ctrl = er32(EXTCNF_CTRL); 549 extcnf_ctrl &= ~E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP; 550 ew32(EXTCNF_CTRL, extcnf_ctrl); 551 } 552 553 static DEFINE_MUTEX(swflag_mutex); 554 555 /** 556 * e1000_get_hw_semaphore_82574 - Acquire hardware semaphore 557 * @hw: pointer to the HW structure 558 * 559 * Acquire the HW semaphore to access the PHY or NVM. 560 * 561 **/ 562 static s32 e1000_get_hw_semaphore_82574(struct e1000_hw *hw) 563 { 564 s32 ret_val; 565 566 mutex_lock(&swflag_mutex); 567 ret_val = e1000_get_hw_semaphore_82573(hw); 568 if (ret_val) 569 mutex_unlock(&swflag_mutex); 570 return ret_val; 571 } 572 573 /** 574 * e1000_put_hw_semaphore_82574 - Release hardware semaphore 575 * @hw: pointer to the HW structure 576 * 577 * Release hardware semaphore used to access the PHY or NVM 578 * 579 **/ 580 static void e1000_put_hw_semaphore_82574(struct e1000_hw *hw) 581 { 582 e1000_put_hw_semaphore_82573(hw); 583 mutex_unlock(&swflag_mutex); 584 } 585 586 /** 587 * e1000_set_d0_lplu_state_82574 - Set Low Power Linkup D0 state 588 * @hw: pointer to the HW structure 589 * @active: true to enable LPLU, false to disable 590 * 591 * Sets the LPLU D0 state according to the active flag. 592 * LPLU will not be activated unless the 593 * device autonegotiation advertisement meets standards of 594 * either 10 or 10/100 or 10/100/1000 at all duplexes. 595 * This is a function pointer entry point only called by 596 * PHY setup routines. 597 **/ 598 static s32 e1000_set_d0_lplu_state_82574(struct e1000_hw *hw, bool active) 599 { 600 u32 data = er32(POEMB); 601 602 if (active) 603 data |= E1000_PHY_CTRL_D0A_LPLU; 604 else 605 data &= ~E1000_PHY_CTRL_D0A_LPLU; 606 607 ew32(POEMB, data); 608 return 0; 609 } 610 611 /** 612 * e1000_set_d3_lplu_state_82574 - Sets low power link up state for D3 613 * @hw: pointer to the HW structure 614 * @active: boolean used to enable/disable lplu 615 * 616 * The low power link up (lplu) state is set to the power management level D3 617 * when active is true, else clear lplu for D3. LPLU 618 * is used during Dx states where the power conservation is most important. 619 * During driver activity, SmartSpeed should be enabled so performance is 620 * maintained. 621 **/ 622 static s32 e1000_set_d3_lplu_state_82574(struct e1000_hw *hw, bool active) 623 { 624 u32 data = er32(POEMB); 625 626 if (!active) { 627 data &= ~E1000_PHY_CTRL_NOND0A_LPLU; 628 } else if ((hw->phy.autoneg_advertised == E1000_ALL_SPEED_DUPLEX) || 629 (hw->phy.autoneg_advertised == E1000_ALL_NOT_GIG) || 630 (hw->phy.autoneg_advertised == E1000_ALL_10_SPEED)) { 631 data |= E1000_PHY_CTRL_NOND0A_LPLU; 632 } 633 634 ew32(POEMB, data); 635 return 0; 636 } 637 638 /** 639 * e1000_acquire_nvm_82571 - Request for access to the EEPROM 640 * @hw: pointer to the HW structure 641 * 642 * To gain access to the EEPROM, first we must obtain a hardware semaphore. 643 * Then for non-82573 hardware, set the EEPROM access request bit and wait 644 * for EEPROM access grant bit. If the access grant bit is not set, release 645 * hardware semaphore. 646 **/ 647 static s32 e1000_acquire_nvm_82571(struct e1000_hw *hw) 648 { 649 s32 ret_val; 650 651 ret_val = e1000_get_hw_semaphore_82571(hw); 652 if (ret_val) 653 return ret_val; 654 655 switch (hw->mac.type) { 656 case e1000_82573: 657 break; 658 default: 659 ret_val = e1000e_acquire_nvm(hw); 660 break; 661 } 662 663 if (ret_val) 664 e1000_put_hw_semaphore_82571(hw); 665 666 return ret_val; 667 } 668 669 /** 670 * e1000_release_nvm_82571 - Release exclusive access to EEPROM 671 * @hw: pointer to the HW structure 672 * 673 * Stop any current commands to the EEPROM and clear the EEPROM request bit. 674 **/ 675 static void e1000_release_nvm_82571(struct e1000_hw *hw) 676 { 677 e1000e_release_nvm(hw); 678 e1000_put_hw_semaphore_82571(hw); 679 } 680 681 /** 682 * e1000_write_nvm_82571 - Write to EEPROM using appropriate interface 683 * @hw: pointer to the HW structure 684 * @offset: offset within the EEPROM to be written to 685 * @words: number of words to write 686 * @data: 16 bit word(s) to be written to the EEPROM 687 * 688 * For non-82573 silicon, write data to EEPROM at offset using SPI interface. 689 * 690 * If e1000e_update_nvm_checksum is not called after this function, the 691 * EEPROM will most likely contain an invalid checksum. 692 **/ 693 static s32 e1000_write_nvm_82571(struct e1000_hw *hw, u16 offset, u16 words, 694 u16 *data) 695 { 696 s32 ret_val; 697 698 switch (hw->mac.type) { 699 case e1000_82573: 700 case e1000_82574: 701 case e1000_82583: 702 ret_val = e1000_write_nvm_eewr_82571(hw, offset, words, data); 703 break; 704 case e1000_82571: 705 case e1000_82572: 706 ret_val = e1000e_write_nvm_spi(hw, offset, words, data); 707 break; 708 default: 709 ret_val = -E1000_ERR_NVM; 710 break; 711 } 712 713 return ret_val; 714 } 715 716 /** 717 * e1000_update_nvm_checksum_82571 - Update EEPROM checksum 718 * @hw: pointer to the HW structure 719 * 720 * Updates the EEPROM checksum by reading/adding each word of the EEPROM 721 * up to the checksum. Then calculates the EEPROM checksum and writes the 722 * value to the EEPROM. 723 **/ 724 static s32 e1000_update_nvm_checksum_82571(struct e1000_hw *hw) 725 { 726 u32 eecd; 727 s32 ret_val; 728 u16 i; 729 730 ret_val = e1000e_update_nvm_checksum_generic(hw); 731 if (ret_val) 732 return ret_val; 733 734 /* If our nvm is an EEPROM, then we're done 735 * otherwise, commit the checksum to the flash NVM. 736 */ 737 if (hw->nvm.type != e1000_nvm_flash_hw) 738 return 0; 739 740 /* Check for pending operations. */ 741 for (i = 0; i < E1000_FLASH_UPDATES; i++) { 742 usleep_range(1000, 2000); 743 if (!(er32(EECD) & E1000_EECD_FLUPD)) 744 break; 745 } 746 747 if (i == E1000_FLASH_UPDATES) 748 return -E1000_ERR_NVM; 749 750 /* Reset the firmware if using STM opcode. */ 751 if ((er32(FLOP) & 0xFF00) == E1000_STM_OPCODE) { 752 /* The enabling of and the actual reset must be done 753 * in two write cycles. 754 */ 755 ew32(HICR, E1000_HICR_FW_RESET_ENABLE); 756 e1e_flush(); 757 ew32(HICR, E1000_HICR_FW_RESET); 758 } 759 760 /* Commit the write to flash */ 761 eecd = er32(EECD) | E1000_EECD_FLUPD; 762 ew32(EECD, eecd); 763 764 for (i = 0; i < E1000_FLASH_UPDATES; i++) { 765 usleep_range(1000, 2000); 766 if (!(er32(EECD) & E1000_EECD_FLUPD)) 767 break; 768 } 769 770 if (i == E1000_FLASH_UPDATES) 771 return -E1000_ERR_NVM; 772 773 return 0; 774 } 775 776 /** 777 * e1000_validate_nvm_checksum_82571 - Validate EEPROM checksum 778 * @hw: pointer to the HW structure 779 * 780 * Calculates the EEPROM checksum by reading/adding each word of the EEPROM 781 * and then verifies that the sum of the EEPROM is equal to 0xBABA. 782 **/ 783 static s32 e1000_validate_nvm_checksum_82571(struct e1000_hw *hw) 784 { 785 if (hw->nvm.type == e1000_nvm_flash_hw) 786 e1000_fix_nvm_checksum_82571(hw); 787 788 return e1000e_validate_nvm_checksum_generic(hw); 789 } 790 791 /** 792 * e1000_write_nvm_eewr_82571 - Write to EEPROM for 82573 silicon 793 * @hw: pointer to the HW structure 794 * @offset: offset within the EEPROM to be written to 795 * @words: number of words to write 796 * @data: 16 bit word(s) to be written to the EEPROM 797 * 798 * After checking for invalid values, poll the EEPROM to ensure the previous 799 * command has completed before trying to write the next word. After write 800 * poll for completion. 801 * 802 * If e1000e_update_nvm_checksum is not called after this function, the 803 * EEPROM will most likely contain an invalid checksum. 804 **/ 805 static s32 e1000_write_nvm_eewr_82571(struct e1000_hw *hw, u16 offset, 806 u16 words, u16 *data) 807 { 808 struct e1000_nvm_info *nvm = &hw->nvm; 809 u32 i, eewr = 0; 810 s32 ret_val = 0; 811 812 /* A check for invalid values: offset too large, too many words, 813 * and not enough words. 814 */ 815 if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) || 816 (words == 0)) { 817 e_dbg("nvm parameter(s) out of bounds\n"); 818 return -E1000_ERR_NVM; 819 } 820 821 for (i = 0; i < words; i++) { 822 eewr = ((data[i] << E1000_NVM_RW_REG_DATA) | 823 ((offset + i) << E1000_NVM_RW_ADDR_SHIFT) | 824 E1000_NVM_RW_REG_START); 825 826 ret_val = e1000e_poll_eerd_eewr_done(hw, E1000_NVM_POLL_WRITE); 827 if (ret_val) 828 break; 829 830 ew32(EEWR, eewr); 831 832 ret_val = e1000e_poll_eerd_eewr_done(hw, E1000_NVM_POLL_WRITE); 833 if (ret_val) 834 break; 835 } 836 837 return ret_val; 838 } 839 840 /** 841 * e1000_get_cfg_done_82571 - Poll for configuration done 842 * @hw: pointer to the HW structure 843 * 844 * Reads the management control register for the config done bit to be set. 845 **/ 846 static s32 e1000_get_cfg_done_82571(struct e1000_hw *hw) 847 { 848 s32 timeout = PHY_CFG_TIMEOUT; 849 850 while (timeout) { 851 if (er32(EEMNGCTL) & E1000_NVM_CFG_DONE_PORT_0) 852 break; 853 usleep_range(1000, 2000); 854 timeout--; 855 } 856 if (!timeout) { 857 e_dbg("MNG configuration cycle has not completed.\n"); 858 return -E1000_ERR_RESET; 859 } 860 861 return 0; 862 } 863 864 /** 865 * e1000_set_d0_lplu_state_82571 - Set Low Power Linkup D0 state 866 * @hw: pointer to the HW structure 867 * @active: true to enable LPLU, false to disable 868 * 869 * Sets the LPLU D0 state according to the active flag. When activating LPLU 870 * this function also disables smart speed and vice versa. LPLU will not be 871 * activated unless the device autonegotiation advertisement meets standards 872 * of either 10 or 10/100 or 10/100/1000 at all duplexes. This is a function 873 * pointer entry point only called by PHY setup routines. 874 **/ 875 static s32 e1000_set_d0_lplu_state_82571(struct e1000_hw *hw, bool active) 876 { 877 struct e1000_phy_info *phy = &hw->phy; 878 s32 ret_val; 879 u16 data; 880 881 ret_val = e1e_rphy(hw, IGP02E1000_PHY_POWER_MGMT, &data); 882 if (ret_val) 883 return ret_val; 884 885 if (active) { 886 data |= IGP02E1000_PM_D0_LPLU; 887 ret_val = e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT, data); 888 if (ret_val) 889 return ret_val; 890 891 /* When LPLU is enabled, we should disable SmartSpeed */ 892 ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, &data); 893 if (ret_val) 894 return ret_val; 895 data &= ~IGP01E1000_PSCFR_SMART_SPEED; 896 ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, data); 897 if (ret_val) 898 return ret_val; 899 } else { 900 data &= ~IGP02E1000_PM_D0_LPLU; 901 ret_val = e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT, data); 902 /* LPLU and SmartSpeed are mutually exclusive. LPLU is used 903 * during Dx states where the power conservation is most 904 * important. During driver activity we should enable 905 * SmartSpeed, so performance is maintained. 906 */ 907 if (phy->smart_speed == e1000_smart_speed_on) { 908 ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, 909 &data); 910 if (ret_val) 911 return ret_val; 912 913 data |= IGP01E1000_PSCFR_SMART_SPEED; 914 ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, 915 data); 916 if (ret_val) 917 return ret_val; 918 } else if (phy->smart_speed == e1000_smart_speed_off) { 919 ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, 920 &data); 921 if (ret_val) 922 return ret_val; 923 924 data &= ~IGP01E1000_PSCFR_SMART_SPEED; 925 ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, 926 data); 927 if (ret_val) 928 return ret_val; 929 } 930 } 931 932 return 0; 933 } 934 935 /** 936 * e1000_reset_hw_82571 - Reset hardware 937 * @hw: pointer to the HW structure 938 * 939 * This resets the hardware into a known state. 940 **/ 941 static s32 e1000_reset_hw_82571(struct e1000_hw *hw) 942 { 943 u32 ctrl, ctrl_ext, eecd, tctl; 944 s32 ret_val; 945 946 /* Prevent the PCI-E bus from sticking if there is no TLP connection 947 * on the last TLP read/write transaction when MAC is reset. 948 */ 949 ret_val = e1000e_disable_pcie_master(hw); 950 if (ret_val) 951 e_dbg("PCI-E Master disable polling has failed.\n"); 952 953 e_dbg("Masking off all interrupts\n"); 954 ew32(IMC, 0xffffffff); 955 956 ew32(RCTL, 0); 957 tctl = er32(TCTL); 958 tctl &= ~E1000_TCTL_EN; 959 ew32(TCTL, tctl); 960 e1e_flush(); 961 962 usleep_range(10000, 11000); 963 964 /* Must acquire the MDIO ownership before MAC reset. 965 * Ownership defaults to firmware after a reset. 966 */ 967 switch (hw->mac.type) { 968 case e1000_82573: 969 ret_val = e1000_get_hw_semaphore_82573(hw); 970 break; 971 case e1000_82574: 972 case e1000_82583: 973 ret_val = e1000_get_hw_semaphore_82574(hw); 974 break; 975 default: 976 break; 977 } 978 979 ctrl = er32(CTRL); 980 981 e_dbg("Issuing a global reset to MAC\n"); 982 ew32(CTRL, ctrl | E1000_CTRL_RST); 983 984 /* Must release MDIO ownership and mutex after MAC reset. */ 985 switch (hw->mac.type) { 986 case e1000_82573: 987 /* Release mutex only if the hw semaphore is acquired */ 988 if (!ret_val) 989 e1000_put_hw_semaphore_82573(hw); 990 break; 991 case e1000_82574: 992 case e1000_82583: 993 /* Release mutex only if the hw semaphore is acquired */ 994 if (!ret_val) 995 e1000_put_hw_semaphore_82574(hw); 996 break; 997 default: 998 break; 999 } 1000 1001 if (hw->nvm.type == e1000_nvm_flash_hw) { 1002 usleep_range(10, 20); 1003 ctrl_ext = er32(CTRL_EXT); 1004 ctrl_ext |= E1000_CTRL_EXT_EE_RST; 1005 ew32(CTRL_EXT, ctrl_ext); 1006 e1e_flush(); 1007 } 1008 1009 ret_val = e1000e_get_auto_rd_done(hw); 1010 if (ret_val) 1011 /* We don't want to continue accessing MAC registers. */ 1012 return ret_val; 1013 1014 /* Phy configuration from NVM just starts after EECD_AUTO_RD is set. 1015 * Need to wait for Phy configuration completion before accessing 1016 * NVM and Phy. 1017 */ 1018 1019 switch (hw->mac.type) { 1020 case e1000_82571: 1021 case e1000_82572: 1022 /* REQ and GNT bits need to be cleared when using AUTO_RD 1023 * to access the EEPROM. 1024 */ 1025 eecd = er32(EECD); 1026 eecd &= ~(E1000_EECD_REQ | E1000_EECD_GNT); 1027 ew32(EECD, eecd); 1028 break; 1029 case e1000_82573: 1030 case e1000_82574: 1031 case e1000_82583: 1032 msleep(25); 1033 break; 1034 default: 1035 break; 1036 } 1037 1038 /* Clear any pending interrupt events. */ 1039 ew32(IMC, 0xffffffff); 1040 er32(ICR); 1041 1042 if (hw->mac.type == e1000_82571) { 1043 /* Install any alternate MAC address into RAR0 */ 1044 ret_val = e1000_check_alt_mac_addr_generic(hw); 1045 if (ret_val) 1046 return ret_val; 1047 1048 e1000e_set_laa_state_82571(hw, true); 1049 } 1050 1051 /* Reinitialize the 82571 serdes link state machine */ 1052 if (hw->phy.media_type == e1000_media_type_internal_serdes) 1053 hw->mac.serdes_link_state = e1000_serdes_link_down; 1054 1055 return 0; 1056 } 1057 1058 /** 1059 * e1000_init_hw_82571 - Initialize hardware 1060 * @hw: pointer to the HW structure 1061 * 1062 * This inits the hardware readying it for operation. 1063 **/ 1064 static s32 e1000_init_hw_82571(struct e1000_hw *hw) 1065 { 1066 struct e1000_mac_info *mac = &hw->mac; 1067 u32 reg_data; 1068 s32 ret_val; 1069 u16 i, rar_count = mac->rar_entry_count; 1070 1071 e1000_initialize_hw_bits_82571(hw); 1072 1073 /* Initialize identification LED */ 1074 ret_val = mac->ops.id_led_init(hw); 1075 /* An error is not fatal and we should not stop init due to this */ 1076 if (ret_val) 1077 e_dbg("Error initializing identification LED\n"); 1078 1079 /* Disabling VLAN filtering */ 1080 e_dbg("Initializing the IEEE VLAN\n"); 1081 mac->ops.clear_vfta(hw); 1082 1083 /* Setup the receive address. 1084 * If, however, a locally administered address was assigned to the 1085 * 82571, we must reserve a RAR for it to work around an issue where 1086 * resetting one port will reload the MAC on the other port. 1087 */ 1088 if (e1000e_get_laa_state_82571(hw)) 1089 rar_count--; 1090 e1000e_init_rx_addrs(hw, rar_count); 1091 1092 /* Zero out the Multicast HASH table */ 1093 e_dbg("Zeroing the MTA\n"); 1094 for (i = 0; i < mac->mta_reg_count; i++) 1095 E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); 1096 1097 /* Setup link and flow control */ 1098 ret_val = mac->ops.setup_link(hw); 1099 1100 /* Set the transmit descriptor write-back policy */ 1101 reg_data = er32(TXDCTL(0)); 1102 reg_data = ((reg_data & ~E1000_TXDCTL_WTHRESH) | 1103 E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC); 1104 ew32(TXDCTL(0), reg_data); 1105 1106 /* ...for both queues. */ 1107 switch (mac->type) { 1108 case e1000_82573: 1109 e1000e_enable_tx_pkt_filtering(hw); 1110 /* fall through */ 1111 case e1000_82574: 1112 case e1000_82583: 1113 reg_data = er32(GCR); 1114 reg_data |= E1000_GCR_L1_ACT_WITHOUT_L0S_RX; 1115 ew32(GCR, reg_data); 1116 break; 1117 default: 1118 reg_data = er32(TXDCTL(1)); 1119 reg_data = ((reg_data & ~E1000_TXDCTL_WTHRESH) | 1120 E1000_TXDCTL_FULL_TX_DESC_WB | 1121 E1000_TXDCTL_COUNT_DESC); 1122 ew32(TXDCTL(1), reg_data); 1123 break; 1124 } 1125 1126 /* Clear all of the statistics registers (clear on read). It is 1127 * important that we do this after we have tried to establish link 1128 * because the symbol error count will increment wildly if there 1129 * is no link. 1130 */ 1131 e1000_clear_hw_cntrs_82571(hw); 1132 1133 return ret_val; 1134 } 1135 1136 /** 1137 * e1000_initialize_hw_bits_82571 - Initialize hardware-dependent bits 1138 * @hw: pointer to the HW structure 1139 * 1140 * Initializes required hardware-dependent bits needed for normal operation. 1141 **/ 1142 static void e1000_initialize_hw_bits_82571(struct e1000_hw *hw) 1143 { 1144 u32 reg; 1145 1146 /* Transmit Descriptor Control 0 */ 1147 reg = er32(TXDCTL(0)); 1148 reg |= BIT(22); 1149 ew32(TXDCTL(0), reg); 1150 1151 /* Transmit Descriptor Control 1 */ 1152 reg = er32(TXDCTL(1)); 1153 reg |= BIT(22); 1154 ew32(TXDCTL(1), reg); 1155 1156 /* Transmit Arbitration Control 0 */ 1157 reg = er32(TARC(0)); 1158 reg &= ~(0xF << 27); /* 30:27 */ 1159 switch (hw->mac.type) { 1160 case e1000_82571: 1161 case e1000_82572: 1162 reg |= BIT(23) | BIT(24) | BIT(25) | BIT(26); 1163 break; 1164 case e1000_82574: 1165 case e1000_82583: 1166 reg |= BIT(26); 1167 break; 1168 default: 1169 break; 1170 } 1171 ew32(TARC(0), reg); 1172 1173 /* Transmit Arbitration Control 1 */ 1174 reg = er32(TARC(1)); 1175 switch (hw->mac.type) { 1176 case e1000_82571: 1177 case e1000_82572: 1178 reg &= ~(BIT(29) | BIT(30)); 1179 reg |= BIT(22) | BIT(24) | BIT(25) | BIT(26); 1180 if (er32(TCTL) & E1000_TCTL_MULR) 1181 reg &= ~BIT(28); 1182 else 1183 reg |= BIT(28); 1184 ew32(TARC(1), reg); 1185 break; 1186 default: 1187 break; 1188 } 1189 1190 /* Device Control */ 1191 switch (hw->mac.type) { 1192 case e1000_82573: 1193 case e1000_82574: 1194 case e1000_82583: 1195 reg = er32(CTRL); 1196 reg &= ~BIT(29); 1197 ew32(CTRL, reg); 1198 break; 1199 default: 1200 break; 1201 } 1202 1203 /* Extended Device Control */ 1204 switch (hw->mac.type) { 1205 case e1000_82573: 1206 case e1000_82574: 1207 case e1000_82583: 1208 reg = er32(CTRL_EXT); 1209 reg &= ~BIT(23); 1210 reg |= BIT(22); 1211 ew32(CTRL_EXT, reg); 1212 break; 1213 default: 1214 break; 1215 } 1216 1217 if (hw->mac.type == e1000_82571) { 1218 reg = er32(PBA_ECC); 1219 reg |= E1000_PBA_ECC_CORR_EN; 1220 ew32(PBA_ECC, reg); 1221 } 1222 1223 /* Workaround for hardware errata. 1224 * Ensure that DMA Dynamic Clock gating is disabled on 82571 and 82572 1225 */ 1226 if ((hw->mac.type == e1000_82571) || (hw->mac.type == e1000_82572)) { 1227 reg = er32(CTRL_EXT); 1228 reg &= ~E1000_CTRL_EXT_DMA_DYN_CLK_EN; 1229 ew32(CTRL_EXT, reg); 1230 } 1231 1232 /* Disable IPv6 extension header parsing because some malformed 1233 * IPv6 headers can hang the Rx. 1234 */ 1235 if (hw->mac.type <= e1000_82573) { 1236 reg = er32(RFCTL); 1237 reg |= (E1000_RFCTL_IPV6_EX_DIS | E1000_RFCTL_NEW_IPV6_EXT_DIS); 1238 ew32(RFCTL, reg); 1239 } 1240 1241 /* PCI-Ex Control Registers */ 1242 switch (hw->mac.type) { 1243 case e1000_82574: 1244 case e1000_82583: 1245 reg = er32(GCR); 1246 reg |= BIT(22); 1247 ew32(GCR, reg); 1248 1249 /* Workaround for hardware errata. 1250 * apply workaround for hardware errata documented in errata 1251 * docs Fixes issue where some error prone or unreliable PCIe 1252 * completions are occurring, particularly with ASPM enabled. 1253 * Without fix, issue can cause Tx timeouts. 1254 */ 1255 reg = er32(GCR2); 1256 reg |= 1; 1257 ew32(GCR2, reg); 1258 break; 1259 default: 1260 break; 1261 } 1262 } 1263 1264 /** 1265 * e1000_clear_vfta_82571 - Clear VLAN filter table 1266 * @hw: pointer to the HW structure 1267 * 1268 * Clears the register array which contains the VLAN filter table by 1269 * setting all the values to 0. 1270 **/ 1271 static void e1000_clear_vfta_82571(struct e1000_hw *hw) 1272 { 1273 u32 offset; 1274 u32 vfta_value = 0; 1275 u32 vfta_offset = 0; 1276 u32 vfta_bit_in_reg = 0; 1277 1278 switch (hw->mac.type) { 1279 case e1000_82573: 1280 case e1000_82574: 1281 case e1000_82583: 1282 if (hw->mng_cookie.vlan_id != 0) { 1283 /* The VFTA is a 4096b bit-field, each identifying 1284 * a single VLAN ID. The following operations 1285 * determine which 32b entry (i.e. offset) into the 1286 * array we want to set the VLAN ID (i.e. bit) of 1287 * the manageability unit. 1288 */ 1289 vfta_offset = (hw->mng_cookie.vlan_id >> 1290 E1000_VFTA_ENTRY_SHIFT) & 1291 E1000_VFTA_ENTRY_MASK; 1292 vfta_bit_in_reg = 1293 BIT(hw->mng_cookie.vlan_id & 1294 E1000_VFTA_ENTRY_BIT_SHIFT_MASK); 1295 } 1296 break; 1297 default: 1298 break; 1299 } 1300 for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) { 1301 /* If the offset we want to clear is the same offset of the 1302 * manageability VLAN ID, then clear all bits except that of 1303 * the manageability unit. 1304 */ 1305 vfta_value = (offset == vfta_offset) ? vfta_bit_in_reg : 0; 1306 E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset, vfta_value); 1307 e1e_flush(); 1308 } 1309 } 1310 1311 /** 1312 * e1000_check_mng_mode_82574 - Check manageability is enabled 1313 * @hw: pointer to the HW structure 1314 * 1315 * Reads the NVM Initialization Control Word 2 and returns true 1316 * (>0) if any manageability is enabled, else false (0). 1317 **/ 1318 static bool e1000_check_mng_mode_82574(struct e1000_hw *hw) 1319 { 1320 u16 data; 1321 1322 e1000_read_nvm(hw, NVM_INIT_CONTROL2_REG, 1, &data); 1323 return (data & E1000_NVM_INIT_CTRL2_MNGM) != 0; 1324 } 1325 1326 /** 1327 * e1000_led_on_82574 - Turn LED on 1328 * @hw: pointer to the HW structure 1329 * 1330 * Turn LED on. 1331 **/ 1332 static s32 e1000_led_on_82574(struct e1000_hw *hw) 1333 { 1334 u32 ctrl; 1335 u32 i; 1336 1337 ctrl = hw->mac.ledctl_mode2; 1338 if (!(E1000_STATUS_LU & er32(STATUS))) { 1339 /* If no link, then turn LED on by setting the invert bit 1340 * for each LED that's "on" (0x0E) in ledctl_mode2. 1341 */ 1342 for (i = 0; i < 4; i++) 1343 if (((hw->mac.ledctl_mode2 >> (i * 8)) & 0xFF) == 1344 E1000_LEDCTL_MODE_LED_ON) 1345 ctrl |= (E1000_LEDCTL_LED0_IVRT << (i * 8)); 1346 } 1347 ew32(LEDCTL, ctrl); 1348 1349 return 0; 1350 } 1351 1352 /** 1353 * e1000_check_phy_82574 - check 82574 phy hung state 1354 * @hw: pointer to the HW structure 1355 * 1356 * Returns whether phy is hung or not 1357 **/ 1358 bool e1000_check_phy_82574(struct e1000_hw *hw) 1359 { 1360 u16 status_1kbt = 0; 1361 u16 receive_errors = 0; 1362 s32 ret_val; 1363 1364 /* Read PHY Receive Error counter first, if its is max - all F's then 1365 * read the Base1000T status register If both are max then PHY is hung. 1366 */ 1367 ret_val = e1e_rphy(hw, E1000_RECEIVE_ERROR_COUNTER, &receive_errors); 1368 if (ret_val) 1369 return false; 1370 if (receive_errors == E1000_RECEIVE_ERROR_MAX) { 1371 ret_val = e1e_rphy(hw, E1000_BASE1000T_STATUS, &status_1kbt); 1372 if (ret_val) 1373 return false; 1374 if ((status_1kbt & E1000_IDLE_ERROR_COUNT_MASK) == 1375 E1000_IDLE_ERROR_COUNT_MASK) 1376 return true; 1377 } 1378 1379 return false; 1380 } 1381 1382 /** 1383 * e1000_setup_link_82571 - Setup flow control and link settings 1384 * @hw: pointer to the HW structure 1385 * 1386 * Determines which flow control settings to use, then configures flow 1387 * control. Calls the appropriate media-specific link configuration 1388 * function. Assuming the adapter has a valid link partner, a valid link 1389 * should be established. Assumes the hardware has previously been reset 1390 * and the transmitter and receiver are not enabled. 1391 **/ 1392 static s32 e1000_setup_link_82571(struct e1000_hw *hw) 1393 { 1394 /* 82573 does not have a word in the NVM to determine 1395 * the default flow control setting, so we explicitly 1396 * set it to full. 1397 */ 1398 switch (hw->mac.type) { 1399 case e1000_82573: 1400 case e1000_82574: 1401 case e1000_82583: 1402 if (hw->fc.requested_mode == e1000_fc_default) 1403 hw->fc.requested_mode = e1000_fc_full; 1404 break; 1405 default: 1406 break; 1407 } 1408 1409 return e1000e_setup_link_generic(hw); 1410 } 1411 1412 /** 1413 * e1000_setup_copper_link_82571 - Configure copper link settings 1414 * @hw: pointer to the HW structure 1415 * 1416 * Configures the link for auto-neg or forced speed and duplex. Then we check 1417 * for link, once link is established calls to configure collision distance 1418 * and flow control are called. 1419 **/ 1420 static s32 e1000_setup_copper_link_82571(struct e1000_hw *hw) 1421 { 1422 u32 ctrl; 1423 s32 ret_val; 1424 1425 ctrl = er32(CTRL); 1426 ctrl |= E1000_CTRL_SLU; 1427 ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); 1428 ew32(CTRL, ctrl); 1429 1430 switch (hw->phy.type) { 1431 case e1000_phy_m88: 1432 case e1000_phy_bm: 1433 ret_val = e1000e_copper_link_setup_m88(hw); 1434 break; 1435 case e1000_phy_igp_2: 1436 ret_val = e1000e_copper_link_setup_igp(hw); 1437 break; 1438 default: 1439 return -E1000_ERR_PHY; 1440 } 1441 1442 if (ret_val) 1443 return ret_val; 1444 1445 return e1000e_setup_copper_link(hw); 1446 } 1447 1448 /** 1449 * e1000_setup_fiber_serdes_link_82571 - Setup link for fiber/serdes 1450 * @hw: pointer to the HW structure 1451 * 1452 * Configures collision distance and flow control for fiber and serdes links. 1453 * Upon successful setup, poll for link. 1454 **/ 1455 static s32 e1000_setup_fiber_serdes_link_82571(struct e1000_hw *hw) 1456 { 1457 switch (hw->mac.type) { 1458 case e1000_82571: 1459 case e1000_82572: 1460 /* If SerDes loopback mode is entered, there is no form 1461 * of reset to take the adapter out of that mode. So we 1462 * have to explicitly take the adapter out of loopback 1463 * mode. This prevents drivers from twiddling their thumbs 1464 * if another tool failed to take it out of loopback mode. 1465 */ 1466 ew32(SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK); 1467 break; 1468 default: 1469 break; 1470 } 1471 1472 return e1000e_setup_fiber_serdes_link(hw); 1473 } 1474 1475 /** 1476 * e1000_check_for_serdes_link_82571 - Check for link (Serdes) 1477 * @hw: pointer to the HW structure 1478 * 1479 * Reports the link state as up or down. 1480 * 1481 * If autonegotiation is supported by the link partner, the link state is 1482 * determined by the result of autonegotiation. This is the most likely case. 1483 * If autonegotiation is not supported by the link partner, and the link 1484 * has a valid signal, force the link up. 1485 * 1486 * The link state is represented internally here by 4 states: 1487 * 1488 * 1) down 1489 * 2) autoneg_progress 1490 * 3) autoneg_complete (the link successfully autonegotiated) 1491 * 4) forced_up (the link has been forced up, it did not autonegotiate) 1492 * 1493 **/ 1494 static s32 e1000_check_for_serdes_link_82571(struct e1000_hw *hw) 1495 { 1496 struct e1000_mac_info *mac = &hw->mac; 1497 u32 rxcw; 1498 u32 ctrl; 1499 u32 status; 1500 u32 txcw; 1501 u32 i; 1502 s32 ret_val = 0; 1503 1504 ctrl = er32(CTRL); 1505 status = er32(STATUS); 1506 er32(RXCW); 1507 /* SYNCH bit and IV bit are sticky */ 1508 usleep_range(10, 20); 1509 rxcw = er32(RXCW); 1510 1511 if ((rxcw & E1000_RXCW_SYNCH) && !(rxcw & E1000_RXCW_IV)) { 1512 /* Receiver is synchronized with no invalid bits. */ 1513 switch (mac->serdes_link_state) { 1514 case e1000_serdes_link_autoneg_complete: 1515 if (!(status & E1000_STATUS_LU)) { 1516 /* We have lost link, retry autoneg before 1517 * reporting link failure 1518 */ 1519 mac->serdes_link_state = 1520 e1000_serdes_link_autoneg_progress; 1521 mac->serdes_has_link = false; 1522 e_dbg("AN_UP -> AN_PROG\n"); 1523 } else { 1524 mac->serdes_has_link = true; 1525 } 1526 break; 1527 1528 case e1000_serdes_link_forced_up: 1529 /* If we are receiving /C/ ordered sets, re-enable 1530 * auto-negotiation in the TXCW register and disable 1531 * forced link in the Device Control register in an 1532 * attempt to auto-negotiate with our link partner. 1533 */ 1534 if (rxcw & E1000_RXCW_C) { 1535 /* Enable autoneg, and unforce link up */ 1536 ew32(TXCW, mac->txcw); 1537 ew32(CTRL, (ctrl & ~E1000_CTRL_SLU)); 1538 mac->serdes_link_state = 1539 e1000_serdes_link_autoneg_progress; 1540 mac->serdes_has_link = false; 1541 e_dbg("FORCED_UP -> AN_PROG\n"); 1542 } else { 1543 mac->serdes_has_link = true; 1544 } 1545 break; 1546 1547 case e1000_serdes_link_autoneg_progress: 1548 if (rxcw & E1000_RXCW_C) { 1549 /* We received /C/ ordered sets, meaning the 1550 * link partner has autonegotiated, and we can 1551 * trust the Link Up (LU) status bit. 1552 */ 1553 if (status & E1000_STATUS_LU) { 1554 mac->serdes_link_state = 1555 e1000_serdes_link_autoneg_complete; 1556 e_dbg("AN_PROG -> AN_UP\n"); 1557 mac->serdes_has_link = true; 1558 } else { 1559 /* Autoneg completed, but failed. */ 1560 mac->serdes_link_state = 1561 e1000_serdes_link_down; 1562 e_dbg("AN_PROG -> DOWN\n"); 1563 } 1564 } else { 1565 /* The link partner did not autoneg. 1566 * Force link up and full duplex, and change 1567 * state to forced. 1568 */ 1569 ew32(TXCW, (mac->txcw & ~E1000_TXCW_ANE)); 1570 ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD); 1571 ew32(CTRL, ctrl); 1572 1573 /* Configure Flow Control after link up. */ 1574 ret_val = e1000e_config_fc_after_link_up(hw); 1575 if (ret_val) { 1576 e_dbg("Error config flow control\n"); 1577 break; 1578 } 1579 mac->serdes_link_state = 1580 e1000_serdes_link_forced_up; 1581 mac->serdes_has_link = true; 1582 e_dbg("AN_PROG -> FORCED_UP\n"); 1583 } 1584 break; 1585 1586 case e1000_serdes_link_down: 1587 default: 1588 /* The link was down but the receiver has now gained 1589 * valid sync, so lets see if we can bring the link 1590 * up. 1591 */ 1592 ew32(TXCW, mac->txcw); 1593 ew32(CTRL, (ctrl & ~E1000_CTRL_SLU)); 1594 mac->serdes_link_state = 1595 e1000_serdes_link_autoneg_progress; 1596 mac->serdes_has_link = false; 1597 e_dbg("DOWN -> AN_PROG\n"); 1598 break; 1599 } 1600 } else { 1601 if (!(rxcw & E1000_RXCW_SYNCH)) { 1602 mac->serdes_has_link = false; 1603 mac->serdes_link_state = e1000_serdes_link_down; 1604 e_dbg("ANYSTATE -> DOWN\n"); 1605 } else { 1606 /* Check several times, if SYNCH bit and CONFIG 1607 * bit both are consistently 1 then simply ignore 1608 * the IV bit and restart Autoneg 1609 */ 1610 for (i = 0; i < AN_RETRY_COUNT; i++) { 1611 usleep_range(10, 20); 1612 rxcw = er32(RXCW); 1613 if ((rxcw & E1000_RXCW_SYNCH) && 1614 (rxcw & E1000_RXCW_C)) 1615 continue; 1616 1617 if (rxcw & E1000_RXCW_IV) { 1618 mac->serdes_has_link = false; 1619 mac->serdes_link_state = 1620 e1000_serdes_link_down; 1621 e_dbg("ANYSTATE -> DOWN\n"); 1622 break; 1623 } 1624 } 1625 1626 if (i == AN_RETRY_COUNT) { 1627 txcw = er32(TXCW); 1628 txcw |= E1000_TXCW_ANE; 1629 ew32(TXCW, txcw); 1630 mac->serdes_link_state = 1631 e1000_serdes_link_autoneg_progress; 1632 mac->serdes_has_link = false; 1633 e_dbg("ANYSTATE -> AN_PROG\n"); 1634 } 1635 } 1636 } 1637 1638 return ret_val; 1639 } 1640 1641 /** 1642 * e1000_valid_led_default_82571 - Verify a valid default LED config 1643 * @hw: pointer to the HW structure 1644 * @data: pointer to the NVM (EEPROM) 1645 * 1646 * Read the EEPROM for the current default LED configuration. If the 1647 * LED configuration is not valid, set to a valid LED configuration. 1648 **/ 1649 static s32 e1000_valid_led_default_82571(struct e1000_hw *hw, u16 *data) 1650 { 1651 s32 ret_val; 1652 1653 ret_val = e1000_read_nvm(hw, NVM_ID_LED_SETTINGS, 1, data); 1654 if (ret_val) { 1655 e_dbg("NVM Read Error\n"); 1656 return ret_val; 1657 } 1658 1659 switch (hw->mac.type) { 1660 case e1000_82573: 1661 case e1000_82574: 1662 case e1000_82583: 1663 if (*data == ID_LED_RESERVED_F746) 1664 *data = ID_LED_DEFAULT_82573; 1665 break; 1666 default: 1667 if (*data == ID_LED_RESERVED_0000 || 1668 *data == ID_LED_RESERVED_FFFF) 1669 *data = ID_LED_DEFAULT; 1670 break; 1671 } 1672 1673 return 0; 1674 } 1675 1676 /** 1677 * e1000e_get_laa_state_82571 - Get locally administered address state 1678 * @hw: pointer to the HW structure 1679 * 1680 * Retrieve and return the current locally administered address state. 1681 **/ 1682 bool e1000e_get_laa_state_82571(struct e1000_hw *hw) 1683 { 1684 if (hw->mac.type != e1000_82571) 1685 return false; 1686 1687 return hw->dev_spec.e82571.laa_is_present; 1688 } 1689 1690 /** 1691 * e1000e_set_laa_state_82571 - Set locally administered address state 1692 * @hw: pointer to the HW structure 1693 * @state: enable/disable locally administered address 1694 * 1695 * Enable/Disable the current locally administered address state. 1696 **/ 1697 void e1000e_set_laa_state_82571(struct e1000_hw *hw, bool state) 1698 { 1699 if (hw->mac.type != e1000_82571) 1700 return; 1701 1702 hw->dev_spec.e82571.laa_is_present = state; 1703 1704 /* If workaround is activated... */ 1705 if (state) 1706 /* Hold a copy of the LAA in RAR[14] This is done so that 1707 * between the time RAR[0] gets clobbered and the time it 1708 * gets fixed, the actual LAA is in one of the RARs and no 1709 * incoming packets directed to this port are dropped. 1710 * Eventually the LAA will be in RAR[0] and RAR[14]. 1711 */ 1712 hw->mac.ops.rar_set(hw, hw->mac.addr, 1713 hw->mac.rar_entry_count - 1); 1714 } 1715 1716 /** 1717 * e1000_fix_nvm_checksum_82571 - Fix EEPROM checksum 1718 * @hw: pointer to the HW structure 1719 * 1720 * Verifies that the EEPROM has completed the update. After updating the 1721 * EEPROM, we need to check bit 15 in work 0x23 for the checksum fix. If 1722 * the checksum fix is not implemented, we need to set the bit and update 1723 * the checksum. Otherwise, if bit 15 is set and the checksum is incorrect, 1724 * we need to return bad checksum. 1725 **/ 1726 static s32 e1000_fix_nvm_checksum_82571(struct e1000_hw *hw) 1727 { 1728 struct e1000_nvm_info *nvm = &hw->nvm; 1729 s32 ret_val; 1730 u16 data; 1731 1732 if (nvm->type != e1000_nvm_flash_hw) 1733 return 0; 1734 1735 /* Check bit 4 of word 10h. If it is 0, firmware is done updating 1736 * 10h-12h. Checksum may need to be fixed. 1737 */ 1738 ret_val = e1000_read_nvm(hw, 0x10, 1, &data); 1739 if (ret_val) 1740 return ret_val; 1741 1742 if (!(data & 0x10)) { 1743 /* Read 0x23 and check bit 15. This bit is a 1 1744 * when the checksum has already been fixed. If 1745 * the checksum is still wrong and this bit is a 1746 * 1, we need to return bad checksum. Otherwise, 1747 * we need to set this bit to a 1 and update the 1748 * checksum. 1749 */ 1750 ret_val = e1000_read_nvm(hw, 0x23, 1, &data); 1751 if (ret_val) 1752 return ret_val; 1753 1754 if (!(data & 0x8000)) { 1755 data |= 0x8000; 1756 ret_val = e1000_write_nvm(hw, 0x23, 1, &data); 1757 if (ret_val) 1758 return ret_val; 1759 ret_val = e1000e_update_nvm_checksum(hw); 1760 if (ret_val) 1761 return ret_val; 1762 } 1763 } 1764 1765 return 0; 1766 } 1767 1768 /** 1769 * e1000_read_mac_addr_82571 - Read device MAC address 1770 * @hw: pointer to the HW structure 1771 **/ 1772 static s32 e1000_read_mac_addr_82571(struct e1000_hw *hw) 1773 { 1774 if (hw->mac.type == e1000_82571) { 1775 s32 ret_val; 1776 1777 /* If there's an alternate MAC address place it in RAR0 1778 * so that it will override the Si installed default perm 1779 * address. 1780 */ 1781 ret_val = e1000_check_alt_mac_addr_generic(hw); 1782 if (ret_val) 1783 return ret_val; 1784 } 1785 1786 return e1000_read_mac_addr_generic(hw); 1787 } 1788 1789 /** 1790 * e1000_power_down_phy_copper_82571 - Remove link during PHY power down 1791 * @hw: pointer to the HW structure 1792 * 1793 * In the case of a PHY power down to save power, or to turn off link during a 1794 * driver unload, or wake on lan is not enabled, remove the link. 1795 **/ 1796 static void e1000_power_down_phy_copper_82571(struct e1000_hw *hw) 1797 { 1798 struct e1000_phy_info *phy = &hw->phy; 1799 struct e1000_mac_info *mac = &hw->mac; 1800 1801 if (!phy->ops.check_reset_block) 1802 return; 1803 1804 /* If the management interface is not enabled, then power down */ 1805 if (!(mac->ops.check_mng_mode(hw) || phy->ops.check_reset_block(hw))) 1806 e1000_power_down_phy_copper(hw); 1807 } 1808 1809 /** 1810 * e1000_clear_hw_cntrs_82571 - Clear device specific hardware counters 1811 * @hw: pointer to the HW structure 1812 * 1813 * Clears the hardware counters by reading the counter registers. 1814 **/ 1815 static void e1000_clear_hw_cntrs_82571(struct e1000_hw *hw) 1816 { 1817 e1000e_clear_hw_cntrs_base(hw); 1818 1819 er32(PRC64); 1820 er32(PRC127); 1821 er32(PRC255); 1822 er32(PRC511); 1823 er32(PRC1023); 1824 er32(PRC1522); 1825 er32(PTC64); 1826 er32(PTC127); 1827 er32(PTC255); 1828 er32(PTC511); 1829 er32(PTC1023); 1830 er32(PTC1522); 1831 1832 er32(ALGNERRC); 1833 er32(RXERRC); 1834 er32(TNCRS); 1835 er32(CEXTERR); 1836 er32(TSCTC); 1837 er32(TSCTFC); 1838 1839 er32(MGTPRC); 1840 er32(MGTPDC); 1841 er32(MGTPTC); 1842 1843 er32(IAC); 1844 er32(ICRXOC); 1845 1846 er32(ICRXPTC); 1847 er32(ICRXATC); 1848 er32(ICTXPTC); 1849 er32(ICTXATC); 1850 er32(ICTXQEC); 1851 er32(ICTXQMTC); 1852 er32(ICRXDMTC); 1853 } 1854 1855 static const struct e1000_mac_operations e82571_mac_ops = { 1856 /* .check_mng_mode: mac type dependent */ 1857 /* .check_for_link: media type dependent */ 1858 .id_led_init = e1000e_id_led_init_generic, 1859 .cleanup_led = e1000e_cleanup_led_generic, 1860 .clear_hw_cntrs = e1000_clear_hw_cntrs_82571, 1861 .get_bus_info = e1000e_get_bus_info_pcie, 1862 .set_lan_id = e1000_set_lan_id_multi_port_pcie, 1863 /* .get_link_up_info: media type dependent */ 1864 /* .led_on: mac type dependent */ 1865 .led_off = e1000e_led_off_generic, 1866 .update_mc_addr_list = e1000e_update_mc_addr_list_generic, 1867 .write_vfta = e1000_write_vfta_generic, 1868 .clear_vfta = e1000_clear_vfta_82571, 1869 .reset_hw = e1000_reset_hw_82571, 1870 .init_hw = e1000_init_hw_82571, 1871 .setup_link = e1000_setup_link_82571, 1872 /* .setup_physical_interface: media type dependent */ 1873 .setup_led = e1000e_setup_led_generic, 1874 .config_collision_dist = e1000e_config_collision_dist_generic, 1875 .read_mac_addr = e1000_read_mac_addr_82571, 1876 .rar_set = e1000e_rar_set_generic, 1877 .rar_get_count = e1000e_rar_get_count_generic, 1878 }; 1879 1880 static const struct e1000_phy_operations e82_phy_ops_igp = { 1881 .acquire = e1000_get_hw_semaphore_82571, 1882 .check_polarity = e1000_check_polarity_igp, 1883 .check_reset_block = e1000e_check_reset_block_generic, 1884 .commit = NULL, 1885 .force_speed_duplex = e1000e_phy_force_speed_duplex_igp, 1886 .get_cfg_done = e1000_get_cfg_done_82571, 1887 .get_cable_length = e1000e_get_cable_length_igp_2, 1888 .get_info = e1000e_get_phy_info_igp, 1889 .read_reg = e1000e_read_phy_reg_igp, 1890 .release = e1000_put_hw_semaphore_82571, 1891 .reset = e1000e_phy_hw_reset_generic, 1892 .set_d0_lplu_state = e1000_set_d0_lplu_state_82571, 1893 .set_d3_lplu_state = e1000e_set_d3_lplu_state, 1894 .write_reg = e1000e_write_phy_reg_igp, 1895 .cfg_on_link_up = NULL, 1896 }; 1897 1898 static const struct e1000_phy_operations e82_phy_ops_m88 = { 1899 .acquire = e1000_get_hw_semaphore_82571, 1900 .check_polarity = e1000_check_polarity_m88, 1901 .check_reset_block = e1000e_check_reset_block_generic, 1902 .commit = e1000e_phy_sw_reset, 1903 .force_speed_duplex = e1000e_phy_force_speed_duplex_m88, 1904 .get_cfg_done = e1000e_get_cfg_done_generic, 1905 .get_cable_length = e1000e_get_cable_length_m88, 1906 .get_info = e1000e_get_phy_info_m88, 1907 .read_reg = e1000e_read_phy_reg_m88, 1908 .release = e1000_put_hw_semaphore_82571, 1909 .reset = e1000e_phy_hw_reset_generic, 1910 .set_d0_lplu_state = e1000_set_d0_lplu_state_82571, 1911 .set_d3_lplu_state = e1000e_set_d3_lplu_state, 1912 .write_reg = e1000e_write_phy_reg_m88, 1913 .cfg_on_link_up = NULL, 1914 }; 1915 1916 static const struct e1000_phy_operations e82_phy_ops_bm = { 1917 .acquire = e1000_get_hw_semaphore_82571, 1918 .check_polarity = e1000_check_polarity_m88, 1919 .check_reset_block = e1000e_check_reset_block_generic, 1920 .commit = e1000e_phy_sw_reset, 1921 .force_speed_duplex = e1000e_phy_force_speed_duplex_m88, 1922 .get_cfg_done = e1000e_get_cfg_done_generic, 1923 .get_cable_length = e1000e_get_cable_length_m88, 1924 .get_info = e1000e_get_phy_info_m88, 1925 .read_reg = e1000e_read_phy_reg_bm2, 1926 .release = e1000_put_hw_semaphore_82571, 1927 .reset = e1000e_phy_hw_reset_generic, 1928 .set_d0_lplu_state = e1000_set_d0_lplu_state_82571, 1929 .set_d3_lplu_state = e1000e_set_d3_lplu_state, 1930 .write_reg = e1000e_write_phy_reg_bm2, 1931 .cfg_on_link_up = NULL, 1932 }; 1933 1934 static const struct e1000_nvm_operations e82571_nvm_ops = { 1935 .acquire = e1000_acquire_nvm_82571, 1936 .read = e1000e_read_nvm_eerd, 1937 .release = e1000_release_nvm_82571, 1938 .reload = e1000e_reload_nvm_generic, 1939 .update = e1000_update_nvm_checksum_82571, 1940 .valid_led_default = e1000_valid_led_default_82571, 1941 .validate = e1000_validate_nvm_checksum_82571, 1942 .write = e1000_write_nvm_82571, 1943 }; 1944 1945 const struct e1000_info e1000_82571_info = { 1946 .mac = e1000_82571, 1947 .flags = FLAG_HAS_HW_VLAN_FILTER 1948 | FLAG_HAS_JUMBO_FRAMES 1949 | FLAG_HAS_WOL 1950 | FLAG_APME_IN_CTRL3 1951 | FLAG_HAS_CTRLEXT_ON_LOAD 1952 | FLAG_HAS_SMART_POWER_DOWN 1953 | FLAG_RESET_OVERWRITES_LAA /* errata */ 1954 | FLAG_TARC_SPEED_MODE_BIT /* errata */ 1955 | FLAG_APME_CHECK_PORT_B, 1956 .flags2 = FLAG2_DISABLE_ASPM_L1 /* errata 13 */ 1957 | FLAG2_DMA_BURST, 1958 .pba = 38, 1959 .max_hw_frame_size = DEFAULT_JUMBO, 1960 .get_variants = e1000_get_variants_82571, 1961 .mac_ops = &e82571_mac_ops, 1962 .phy_ops = &e82_phy_ops_igp, 1963 .nvm_ops = &e82571_nvm_ops, 1964 }; 1965 1966 const struct e1000_info e1000_82572_info = { 1967 .mac = e1000_82572, 1968 .flags = FLAG_HAS_HW_VLAN_FILTER 1969 | FLAG_HAS_JUMBO_FRAMES 1970 | FLAG_HAS_WOL 1971 | FLAG_APME_IN_CTRL3 1972 | FLAG_HAS_CTRLEXT_ON_LOAD 1973 | FLAG_TARC_SPEED_MODE_BIT, /* errata */ 1974 .flags2 = FLAG2_DISABLE_ASPM_L1 /* errata 13 */ 1975 | FLAG2_DMA_BURST, 1976 .pba = 38, 1977 .max_hw_frame_size = DEFAULT_JUMBO, 1978 .get_variants = e1000_get_variants_82571, 1979 .mac_ops = &e82571_mac_ops, 1980 .phy_ops = &e82_phy_ops_igp, 1981 .nvm_ops = &e82571_nvm_ops, 1982 }; 1983 1984 const struct e1000_info e1000_82573_info = { 1985 .mac = e1000_82573, 1986 .flags = FLAG_HAS_HW_VLAN_FILTER 1987 | FLAG_HAS_WOL 1988 | FLAG_APME_IN_CTRL3 1989 | FLAG_HAS_SMART_POWER_DOWN 1990 | FLAG_HAS_AMT 1991 | FLAG_HAS_SWSM_ON_LOAD, 1992 .flags2 = FLAG2_DISABLE_ASPM_L1 1993 | FLAG2_DISABLE_ASPM_L0S, 1994 .pba = 20, 1995 .max_hw_frame_size = VLAN_ETH_FRAME_LEN + ETH_FCS_LEN, 1996 .get_variants = e1000_get_variants_82571, 1997 .mac_ops = &e82571_mac_ops, 1998 .phy_ops = &e82_phy_ops_m88, 1999 .nvm_ops = &e82571_nvm_ops, 2000 }; 2001 2002 const struct e1000_info e1000_82574_info = { 2003 .mac = e1000_82574, 2004 .flags = FLAG_HAS_HW_VLAN_FILTER 2005 | FLAG_HAS_MSIX 2006 | FLAG_HAS_JUMBO_FRAMES 2007 | FLAG_HAS_WOL 2008 | FLAG_HAS_HW_TIMESTAMP 2009 | FLAG_APME_IN_CTRL3 2010 | FLAG_HAS_SMART_POWER_DOWN 2011 | FLAG_HAS_AMT 2012 | FLAG_HAS_CTRLEXT_ON_LOAD, 2013 .flags2 = FLAG2_CHECK_PHY_HANG 2014 | FLAG2_DISABLE_ASPM_L0S 2015 | FLAG2_DISABLE_ASPM_L1 2016 | FLAG2_NO_DISABLE_RX 2017 | FLAG2_DMA_BURST 2018 | FLAG2_CHECK_SYSTIM_OVERFLOW, 2019 .pba = 32, 2020 .max_hw_frame_size = DEFAULT_JUMBO, 2021 .get_variants = e1000_get_variants_82571, 2022 .mac_ops = &e82571_mac_ops, 2023 .phy_ops = &e82_phy_ops_bm, 2024 .nvm_ops = &e82571_nvm_ops, 2025 }; 2026 2027 const struct e1000_info e1000_82583_info = { 2028 .mac = e1000_82583, 2029 .flags = FLAG_HAS_HW_VLAN_FILTER 2030 | FLAG_HAS_WOL 2031 | FLAG_HAS_HW_TIMESTAMP 2032 | FLAG_APME_IN_CTRL3 2033 | FLAG_HAS_SMART_POWER_DOWN 2034 | FLAG_HAS_AMT 2035 | FLAG_HAS_JUMBO_FRAMES 2036 | FLAG_HAS_CTRLEXT_ON_LOAD, 2037 .flags2 = FLAG2_DISABLE_ASPM_L0S 2038 | FLAG2_DISABLE_ASPM_L1 2039 | FLAG2_NO_DISABLE_RX 2040 | FLAG2_CHECK_SYSTIM_OVERFLOW, 2041 .pba = 32, 2042 .max_hw_frame_size = DEFAULT_JUMBO, 2043 .get_variants = e1000_get_variants_82571, 2044 .mac_ops = &e82571_mac_ops, 2045 .phy_ops = &e82_phy_ops_bm, 2046 .nvm_ops = &e82571_nvm_ops, 2047 }; 2048