1 // SPDX-License-Identifier: GPL-2.0 2 /* Copyright(c) 1999 - 2018 Intel Corporation. */ 3 4 /* 80003ES2LAN Gigabit Ethernet Controller (Copper) 5 * 80003ES2LAN Gigabit Ethernet Controller (Serdes) 6 */ 7 8 #include "e1000.h" 9 10 /* A table for the GG82563 cable length where the range is defined 11 * with a lower bound at "index" and the upper bound at 12 * "index + 5". 13 */ 14 static const u16 e1000_gg82563_cable_length_table[] = { 15 0, 60, 115, 150, 150, 60, 115, 150, 180, 180, 0xFF 16 }; 17 18 #define GG82563_CABLE_LENGTH_TABLE_SIZE \ 19 ARRAY_SIZE(e1000_gg82563_cable_length_table) 20 21 static s32 e1000_setup_copper_link_80003es2lan(struct e1000_hw *hw); 22 static s32 e1000_acquire_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask); 23 static void e1000_release_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask); 24 static void e1000_initialize_hw_bits_80003es2lan(struct e1000_hw *hw); 25 static void e1000_clear_hw_cntrs_80003es2lan(struct e1000_hw *hw); 26 static s32 e1000_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw); 27 static s32 e1000_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex); 28 static s32 e1000_read_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset, 29 u16 *data); 30 static s32 e1000_write_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset, 31 u16 data); 32 static void e1000_power_down_phy_copper_80003es2lan(struct e1000_hw *hw); 33 34 /** 35 * e1000_init_phy_params_80003es2lan - Init ESB2 PHY func ptrs. 36 * @hw: pointer to the HW structure 37 **/ 38 static s32 e1000_init_phy_params_80003es2lan(struct e1000_hw *hw) 39 { 40 struct e1000_phy_info *phy = &hw->phy; 41 s32 ret_val; 42 43 if (hw->phy.media_type != e1000_media_type_copper) { 44 phy->type = e1000_phy_none; 45 return 0; 46 } else { 47 phy->ops.power_up = e1000_power_up_phy_copper; 48 phy->ops.power_down = e1000_power_down_phy_copper_80003es2lan; 49 } 50 51 phy->addr = 1; 52 phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; 53 phy->reset_delay_us = 100; 54 phy->type = e1000_phy_gg82563; 55 56 /* This can only be done after all function pointers are setup. */ 57 ret_val = e1000e_get_phy_id(hw); 58 59 /* Verify phy id */ 60 if (phy->id != GG82563_E_PHY_ID) 61 return -E1000_ERR_PHY; 62 63 return ret_val; 64 } 65 66 /** 67 * e1000_init_nvm_params_80003es2lan - Init ESB2 NVM func ptrs. 68 * @hw: pointer to the HW structure 69 **/ 70 static s32 e1000_init_nvm_params_80003es2lan(struct e1000_hw *hw) 71 { 72 struct e1000_nvm_info *nvm = &hw->nvm; 73 u32 eecd = er32(EECD); 74 u16 size; 75 76 nvm->opcode_bits = 8; 77 nvm->delay_usec = 1; 78 switch (nvm->override) { 79 case e1000_nvm_override_spi_large: 80 nvm->page_size = 32; 81 nvm->address_bits = 16; 82 break; 83 case e1000_nvm_override_spi_small: 84 nvm->page_size = 8; 85 nvm->address_bits = 8; 86 break; 87 default: 88 nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8; 89 nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8; 90 break; 91 } 92 93 nvm->type = e1000_nvm_eeprom_spi; 94 95 size = (u16)FIELD_GET(E1000_EECD_SIZE_EX_MASK, eecd); 96 97 /* Added to a constant, "size" becomes the left-shift value 98 * for setting word_size. 99 */ 100 size += NVM_WORD_SIZE_BASE_SHIFT; 101 102 /* EEPROM access above 16k is unsupported */ 103 if (size > 14) 104 size = 14; 105 nvm->word_size = BIT(size); 106 107 return 0; 108 } 109 110 /** 111 * e1000_init_mac_params_80003es2lan - Init ESB2 MAC func ptrs. 112 * @hw: pointer to the HW structure 113 **/ 114 static s32 e1000_init_mac_params_80003es2lan(struct e1000_hw *hw) 115 { 116 struct e1000_mac_info *mac = &hw->mac; 117 118 /* Set media type and media-dependent function pointers */ 119 switch (hw->adapter->pdev->device) { 120 case E1000_DEV_ID_80003ES2LAN_SERDES_DPT: 121 hw->phy.media_type = e1000_media_type_internal_serdes; 122 mac->ops.check_for_link = e1000e_check_for_serdes_link; 123 mac->ops.setup_physical_interface = 124 e1000e_setup_fiber_serdes_link; 125 break; 126 default: 127 hw->phy.media_type = e1000_media_type_copper; 128 mac->ops.check_for_link = e1000e_check_for_copper_link; 129 mac->ops.setup_physical_interface = 130 e1000_setup_copper_link_80003es2lan; 131 break; 132 } 133 134 /* Set mta register count */ 135 mac->mta_reg_count = 128; 136 /* Set rar entry count */ 137 mac->rar_entry_count = E1000_RAR_ENTRIES; 138 /* FWSM register */ 139 mac->has_fwsm = true; 140 /* ARC supported; valid only if manageability features are enabled. */ 141 mac->arc_subsystem_valid = !!(er32(FWSM) & E1000_FWSM_MODE_MASK); 142 /* Adaptive IFS not supported */ 143 mac->adaptive_ifs = false; 144 145 /* set lan id for port to determine which phy lock to use */ 146 hw->mac.ops.set_lan_id(hw); 147 148 return 0; 149 } 150 151 static s32 e1000_get_variants_80003es2lan(struct e1000_adapter *adapter) 152 { 153 struct e1000_hw *hw = &adapter->hw; 154 s32 rc; 155 156 rc = e1000_init_mac_params_80003es2lan(hw); 157 if (rc) 158 return rc; 159 160 rc = e1000_init_nvm_params_80003es2lan(hw); 161 if (rc) 162 return rc; 163 164 rc = e1000_init_phy_params_80003es2lan(hw); 165 if (rc) 166 return rc; 167 168 return 0; 169 } 170 171 /** 172 * e1000_acquire_phy_80003es2lan - Acquire rights to access PHY 173 * @hw: pointer to the HW structure 174 * 175 * A wrapper to acquire access rights to the correct PHY. 176 **/ 177 static s32 e1000_acquire_phy_80003es2lan(struct e1000_hw *hw) 178 { 179 u16 mask; 180 181 mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM; 182 return e1000_acquire_swfw_sync_80003es2lan(hw, mask); 183 } 184 185 /** 186 * e1000_release_phy_80003es2lan - Release rights to access PHY 187 * @hw: pointer to the HW structure 188 * 189 * A wrapper to release access rights to the correct PHY. 190 **/ 191 static void e1000_release_phy_80003es2lan(struct e1000_hw *hw) 192 { 193 u16 mask; 194 195 mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM; 196 e1000_release_swfw_sync_80003es2lan(hw, mask); 197 } 198 199 /** 200 * e1000_acquire_mac_csr_80003es2lan - Acquire right to access Kumeran register 201 * @hw: pointer to the HW structure 202 * 203 * Acquire the semaphore to access the Kumeran interface. 204 * 205 **/ 206 static s32 e1000_acquire_mac_csr_80003es2lan(struct e1000_hw *hw) 207 { 208 u16 mask; 209 210 mask = E1000_SWFW_CSR_SM; 211 212 return e1000_acquire_swfw_sync_80003es2lan(hw, mask); 213 } 214 215 /** 216 * e1000_release_mac_csr_80003es2lan - Release right to access Kumeran Register 217 * @hw: pointer to the HW structure 218 * 219 * Release the semaphore used to access the Kumeran interface 220 **/ 221 static void e1000_release_mac_csr_80003es2lan(struct e1000_hw *hw) 222 { 223 u16 mask; 224 225 mask = E1000_SWFW_CSR_SM; 226 227 e1000_release_swfw_sync_80003es2lan(hw, mask); 228 } 229 230 /** 231 * e1000_acquire_nvm_80003es2lan - Acquire rights to access NVM 232 * @hw: pointer to the HW structure 233 * 234 * Acquire the semaphore to access the EEPROM. 235 **/ 236 static s32 e1000_acquire_nvm_80003es2lan(struct e1000_hw *hw) 237 { 238 s32 ret_val; 239 240 ret_val = e1000_acquire_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM); 241 if (ret_val) 242 return ret_val; 243 244 ret_val = e1000e_acquire_nvm(hw); 245 246 if (ret_val) 247 e1000_release_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM); 248 249 return ret_val; 250 } 251 252 /** 253 * e1000_release_nvm_80003es2lan - Relinquish rights to access NVM 254 * @hw: pointer to the HW structure 255 * 256 * Release the semaphore used to access the EEPROM. 257 **/ 258 static void e1000_release_nvm_80003es2lan(struct e1000_hw *hw) 259 { 260 e1000e_release_nvm(hw); 261 e1000_release_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM); 262 } 263 264 /** 265 * e1000_acquire_swfw_sync_80003es2lan - Acquire SW/FW semaphore 266 * @hw: pointer to the HW structure 267 * @mask: specifies which semaphore to acquire 268 * 269 * Acquire the SW/FW semaphore to access the PHY or NVM. The mask 270 * will also specify which port we're acquiring the lock for. 271 **/ 272 static s32 e1000_acquire_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask) 273 { 274 u32 swfw_sync; 275 u32 swmask = mask; 276 u32 fwmask = mask << 16; 277 s32 i = 0; 278 s32 timeout = 50; 279 280 while (i < timeout) { 281 if (e1000e_get_hw_semaphore(hw)) 282 return -E1000_ERR_SWFW_SYNC; 283 284 swfw_sync = er32(SW_FW_SYNC); 285 if (!(swfw_sync & (fwmask | swmask))) 286 break; 287 288 /* Firmware currently using resource (fwmask) 289 * or other software thread using resource (swmask) 290 */ 291 e1000e_put_hw_semaphore(hw); 292 mdelay(5); 293 i++; 294 } 295 296 if (i == timeout) { 297 e_dbg("Driver can't access resource, SW_FW_SYNC timeout.\n"); 298 return -E1000_ERR_SWFW_SYNC; 299 } 300 301 swfw_sync |= swmask; 302 ew32(SW_FW_SYNC, swfw_sync); 303 304 e1000e_put_hw_semaphore(hw); 305 306 return 0; 307 } 308 309 /** 310 * e1000_release_swfw_sync_80003es2lan - Release SW/FW semaphore 311 * @hw: pointer to the HW structure 312 * @mask: specifies which semaphore to acquire 313 * 314 * Release the SW/FW semaphore used to access the PHY or NVM. The mask 315 * will also specify which port we're releasing the lock for. 316 **/ 317 static void e1000_release_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask) 318 { 319 u32 swfw_sync; 320 321 while (e1000e_get_hw_semaphore(hw) != 0) 322 ; /* Empty */ 323 324 swfw_sync = er32(SW_FW_SYNC); 325 swfw_sync &= ~mask; 326 ew32(SW_FW_SYNC, swfw_sync); 327 328 e1000e_put_hw_semaphore(hw); 329 } 330 331 /** 332 * e1000_read_phy_reg_gg82563_80003es2lan - Read GG82563 PHY register 333 * @hw: pointer to the HW structure 334 * @offset: offset of the register to read 335 * @data: pointer to the data returned from the operation 336 * 337 * Read the GG82563 PHY register. 338 **/ 339 static s32 e1000_read_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw, 340 u32 offset, u16 *data) 341 { 342 s32 ret_val; 343 u32 page_select; 344 u16 temp; 345 346 ret_val = e1000_acquire_phy_80003es2lan(hw); 347 if (ret_val) 348 return ret_val; 349 350 /* Select Configuration Page */ 351 if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) { 352 page_select = GG82563_PHY_PAGE_SELECT; 353 } else { 354 /* Use Alternative Page Select register to access 355 * registers 30 and 31 356 */ 357 page_select = GG82563_PHY_PAGE_SELECT_ALT; 358 } 359 360 temp = (u16)((u16)offset >> GG82563_PAGE_SHIFT); 361 ret_val = e1000e_write_phy_reg_mdic(hw, page_select, temp); 362 if (ret_val) { 363 e1000_release_phy_80003es2lan(hw); 364 return ret_val; 365 } 366 367 if (hw->dev_spec.e80003es2lan.mdic_wa_enable) { 368 /* The "ready" bit in the MDIC register may be incorrectly set 369 * before the device has completed the "Page Select" MDI 370 * transaction. So we wait 200us after each MDI command... 371 */ 372 usleep_range(200, 400); 373 374 /* ...and verify the command was successful. */ 375 ret_val = e1000e_read_phy_reg_mdic(hw, page_select, &temp); 376 377 if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) { 378 e1000_release_phy_80003es2lan(hw); 379 return -E1000_ERR_PHY; 380 } 381 382 usleep_range(200, 400); 383 384 ret_val = e1000e_read_phy_reg_mdic(hw, 385 MAX_PHY_REG_ADDRESS & offset, 386 data); 387 388 usleep_range(200, 400); 389 } else { 390 ret_val = e1000e_read_phy_reg_mdic(hw, 391 MAX_PHY_REG_ADDRESS & offset, 392 data); 393 } 394 395 e1000_release_phy_80003es2lan(hw); 396 397 return ret_val; 398 } 399 400 /** 401 * e1000_write_phy_reg_gg82563_80003es2lan - Write GG82563 PHY register 402 * @hw: pointer to the HW structure 403 * @offset: offset of the register to read 404 * @data: value to write to the register 405 * 406 * Write to the GG82563 PHY register. 407 **/ 408 static s32 e1000_write_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw, 409 u32 offset, u16 data) 410 { 411 s32 ret_val; 412 u32 page_select; 413 u16 temp; 414 415 ret_val = e1000_acquire_phy_80003es2lan(hw); 416 if (ret_val) 417 return ret_val; 418 419 /* Select Configuration Page */ 420 if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) { 421 page_select = GG82563_PHY_PAGE_SELECT; 422 } else { 423 /* Use Alternative Page Select register to access 424 * registers 30 and 31 425 */ 426 page_select = GG82563_PHY_PAGE_SELECT_ALT; 427 } 428 429 temp = (u16)((u16)offset >> GG82563_PAGE_SHIFT); 430 ret_val = e1000e_write_phy_reg_mdic(hw, page_select, temp); 431 if (ret_val) { 432 e1000_release_phy_80003es2lan(hw); 433 return ret_val; 434 } 435 436 if (hw->dev_spec.e80003es2lan.mdic_wa_enable) { 437 /* The "ready" bit in the MDIC register may be incorrectly set 438 * before the device has completed the "Page Select" MDI 439 * transaction. So we wait 200us after each MDI command... 440 */ 441 usleep_range(200, 400); 442 443 /* ...and verify the command was successful. */ 444 ret_val = e1000e_read_phy_reg_mdic(hw, page_select, &temp); 445 446 if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) { 447 e1000_release_phy_80003es2lan(hw); 448 return -E1000_ERR_PHY; 449 } 450 451 usleep_range(200, 400); 452 453 ret_val = e1000e_write_phy_reg_mdic(hw, 454 MAX_PHY_REG_ADDRESS & 455 offset, data); 456 457 usleep_range(200, 400); 458 } else { 459 ret_val = e1000e_write_phy_reg_mdic(hw, 460 MAX_PHY_REG_ADDRESS & 461 offset, data); 462 } 463 464 e1000_release_phy_80003es2lan(hw); 465 466 return ret_val; 467 } 468 469 /** 470 * e1000_write_nvm_80003es2lan - Write to ESB2 NVM 471 * @hw: pointer to the HW structure 472 * @offset: offset of the register to read 473 * @words: number of words to write 474 * @data: buffer of data to write to the NVM 475 * 476 * Write "words" of data to the ESB2 NVM. 477 **/ 478 static s32 e1000_write_nvm_80003es2lan(struct e1000_hw *hw, u16 offset, 479 u16 words, u16 *data) 480 { 481 return e1000e_write_nvm_spi(hw, offset, words, data); 482 } 483 484 /** 485 * e1000_get_cfg_done_80003es2lan - Wait for configuration to complete 486 * @hw: pointer to the HW structure 487 * 488 * Wait a specific amount of time for manageability processes to complete. 489 * This is a function pointer entry point called by the phy module. 490 **/ 491 static s32 e1000_get_cfg_done_80003es2lan(struct e1000_hw *hw) 492 { 493 s32 timeout = PHY_CFG_TIMEOUT; 494 u32 mask = E1000_NVM_CFG_DONE_PORT_0; 495 496 if (hw->bus.func == 1) 497 mask = E1000_NVM_CFG_DONE_PORT_1; 498 499 while (timeout) { 500 if (er32(EEMNGCTL) & mask) 501 break; 502 usleep_range(1000, 2000); 503 timeout--; 504 } 505 if (!timeout) { 506 e_dbg("MNG configuration cycle has not completed.\n"); 507 return -E1000_ERR_RESET; 508 } 509 510 return 0; 511 } 512 513 /** 514 * e1000_phy_force_speed_duplex_80003es2lan - Force PHY speed and duplex 515 * @hw: pointer to the HW structure 516 * 517 * Force the speed and duplex settings onto the PHY. This is a 518 * function pointer entry point called by the phy module. 519 **/ 520 static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw) 521 { 522 s32 ret_val; 523 u16 phy_data; 524 bool link; 525 526 /* Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI 527 * forced whenever speed and duplex are forced. 528 */ 529 ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); 530 if (ret_val) 531 return ret_val; 532 533 phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_AUTO; 534 ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL, phy_data); 535 if (ret_val) 536 return ret_val; 537 538 e_dbg("GG82563 PSCR: %X\n", phy_data); 539 540 ret_val = e1e_rphy(hw, MII_BMCR, &phy_data); 541 if (ret_val) 542 return ret_val; 543 544 e1000e_phy_force_speed_duplex_setup(hw, &phy_data); 545 546 /* Reset the phy to commit changes. */ 547 phy_data |= BMCR_RESET; 548 549 ret_val = e1e_wphy(hw, MII_BMCR, phy_data); 550 if (ret_val) 551 return ret_val; 552 553 udelay(1); 554 555 if (hw->phy.autoneg_wait_to_complete) { 556 e_dbg("Waiting for forced speed/duplex link on GG82563 phy.\n"); 557 558 ret_val = e1000e_phy_has_link_generic(hw, PHY_FORCE_LIMIT, 559 100000, &link); 560 if (ret_val) 561 return ret_val; 562 563 if (!link) { 564 /* We didn't get link. 565 * Reset the DSP and cross our fingers. 566 */ 567 ret_val = e1000e_phy_reset_dsp(hw); 568 if (ret_val) 569 return ret_val; 570 } 571 572 /* Try once more */ 573 ret_val = e1000e_phy_has_link_generic(hw, PHY_FORCE_LIMIT, 574 100000, &link); 575 if (ret_val) 576 return ret_val; 577 } 578 579 ret_val = e1e_rphy(hw, GG82563_PHY_MAC_SPEC_CTRL, &phy_data); 580 if (ret_val) 581 return ret_val; 582 583 /* Resetting the phy means we need to verify the TX_CLK corresponds 584 * to the link speed. 10Mbps -> 2.5MHz, else 25MHz. 585 */ 586 phy_data &= ~GG82563_MSCR_TX_CLK_MASK; 587 if (hw->mac.forced_speed_duplex & E1000_ALL_10_SPEED) 588 phy_data |= GG82563_MSCR_TX_CLK_10MBPS_2_5; 589 else 590 phy_data |= GG82563_MSCR_TX_CLK_100MBPS_25; 591 592 /* In addition, we must re-enable CRS on Tx for both half and full 593 * duplex. 594 */ 595 phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX; 596 ret_val = e1e_wphy(hw, GG82563_PHY_MAC_SPEC_CTRL, phy_data); 597 598 return ret_val; 599 } 600 601 /** 602 * e1000_get_cable_length_80003es2lan - Set approximate cable length 603 * @hw: pointer to the HW structure 604 * 605 * Find the approximate cable length as measured by the GG82563 PHY. 606 * This is a function pointer entry point called by the phy module. 607 **/ 608 static s32 e1000_get_cable_length_80003es2lan(struct e1000_hw *hw) 609 { 610 struct e1000_phy_info *phy = &hw->phy; 611 s32 ret_val; 612 u16 phy_data, index; 613 614 ret_val = e1e_rphy(hw, GG82563_PHY_DSP_DISTANCE, &phy_data); 615 if (ret_val) 616 return ret_val; 617 618 index = phy_data & GG82563_DSPD_CABLE_LENGTH; 619 620 if (index >= GG82563_CABLE_LENGTH_TABLE_SIZE - 5) 621 return -E1000_ERR_PHY; 622 623 phy->min_cable_length = e1000_gg82563_cable_length_table[index]; 624 phy->max_cable_length = e1000_gg82563_cable_length_table[index + 5]; 625 626 phy->cable_length = (phy->min_cable_length + phy->max_cable_length) / 2; 627 628 return 0; 629 } 630 631 /** 632 * e1000_get_link_up_info_80003es2lan - Report speed and duplex 633 * @hw: pointer to the HW structure 634 * @speed: pointer to speed buffer 635 * @duplex: pointer to duplex buffer 636 * 637 * Retrieve the current speed and duplex configuration. 638 **/ 639 static s32 e1000_get_link_up_info_80003es2lan(struct e1000_hw *hw, u16 *speed, 640 u16 *duplex) 641 { 642 s32 ret_val; 643 644 if (hw->phy.media_type == e1000_media_type_copper) { 645 ret_val = e1000e_get_speed_and_duplex_copper(hw, speed, duplex); 646 hw->phy.ops.cfg_on_link_up(hw); 647 } else { 648 ret_val = e1000e_get_speed_and_duplex_fiber_serdes(hw, 649 speed, 650 duplex); 651 } 652 653 return ret_val; 654 } 655 656 /** 657 * e1000_reset_hw_80003es2lan - Reset the ESB2 controller 658 * @hw: pointer to the HW structure 659 * 660 * Perform a global reset to the ESB2 controller. 661 **/ 662 static s32 e1000_reset_hw_80003es2lan(struct e1000_hw *hw) 663 { 664 u32 ctrl; 665 s32 ret_val; 666 u16 kum_reg_data; 667 668 /* Prevent the PCI-E bus from sticking if there is no TLP connection 669 * on the last TLP read/write transaction when MAC is reset. 670 */ 671 ret_val = e1000e_disable_pcie_master(hw); 672 if (ret_val) 673 e_dbg("PCI-E Master disable polling has failed.\n"); 674 675 e_dbg("Masking off all interrupts\n"); 676 ew32(IMC, 0xffffffff); 677 678 ew32(RCTL, 0); 679 ew32(TCTL, E1000_TCTL_PSP); 680 e1e_flush(); 681 682 usleep_range(10000, 11000); 683 684 ctrl = er32(CTRL); 685 686 ret_val = e1000_acquire_phy_80003es2lan(hw); 687 if (ret_val) 688 return ret_val; 689 690 e_dbg("Issuing a global reset to MAC\n"); 691 ew32(CTRL, ctrl | E1000_CTRL_RST); 692 e1000_release_phy_80003es2lan(hw); 693 694 /* Disable IBIST slave mode (far-end loopback) */ 695 ret_val = 696 e1000_read_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_INBAND_PARAM, 697 &kum_reg_data); 698 if (!ret_val) { 699 kum_reg_data |= E1000_KMRNCTRLSTA_IBIST_DISABLE; 700 ret_val = e1000_write_kmrn_reg_80003es2lan(hw, 701 E1000_KMRNCTRLSTA_INBAND_PARAM, 702 kum_reg_data); 703 if (ret_val) 704 e_dbg("Error disabling far-end loopback\n"); 705 } else { 706 e_dbg("Error disabling far-end loopback\n"); 707 } 708 709 ret_val = e1000e_get_auto_rd_done(hw); 710 if (ret_val) 711 /* We don't want to continue accessing MAC registers. */ 712 return ret_val; 713 714 /* Clear any pending interrupt events. */ 715 ew32(IMC, 0xffffffff); 716 er32(ICR); 717 718 return e1000_check_alt_mac_addr_generic(hw); 719 } 720 721 /** 722 * e1000_init_hw_80003es2lan - Initialize the ESB2 controller 723 * @hw: pointer to the HW structure 724 * 725 * Initialize the hw bits, LED, VFTA, MTA, link and hw counters. 726 **/ 727 static s32 e1000_init_hw_80003es2lan(struct e1000_hw *hw) 728 { 729 struct e1000_mac_info *mac = &hw->mac; 730 u32 reg_data; 731 s32 ret_val; 732 u16 kum_reg_data; 733 u16 i; 734 735 e1000_initialize_hw_bits_80003es2lan(hw); 736 737 /* Initialize identification LED */ 738 ret_val = mac->ops.id_led_init(hw); 739 /* An error is not fatal and we should not stop init due to this */ 740 if (ret_val) 741 e_dbg("Error initializing identification LED\n"); 742 743 /* Disabling VLAN filtering */ 744 e_dbg("Initializing the IEEE VLAN\n"); 745 mac->ops.clear_vfta(hw); 746 747 /* Setup the receive address. */ 748 e1000e_init_rx_addrs(hw, mac->rar_entry_count); 749 750 /* Zero out the Multicast HASH table */ 751 e_dbg("Zeroing the MTA\n"); 752 for (i = 0; i < mac->mta_reg_count; i++) 753 E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); 754 755 /* Setup link and flow control */ 756 ret_val = mac->ops.setup_link(hw); 757 if (ret_val) 758 return ret_val; 759 760 /* Disable IBIST slave mode (far-end loopback) */ 761 ret_val = 762 e1000_read_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_INBAND_PARAM, 763 &kum_reg_data); 764 if (!ret_val) { 765 kum_reg_data |= E1000_KMRNCTRLSTA_IBIST_DISABLE; 766 ret_val = e1000_write_kmrn_reg_80003es2lan(hw, 767 E1000_KMRNCTRLSTA_INBAND_PARAM, 768 kum_reg_data); 769 if (ret_val) 770 e_dbg("Error disabling far-end loopback\n"); 771 } else { 772 e_dbg("Error disabling far-end loopback\n"); 773 } 774 775 /* Set the transmit descriptor write-back policy */ 776 reg_data = er32(TXDCTL(0)); 777 reg_data = ((reg_data & ~E1000_TXDCTL_WTHRESH) | 778 E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC); 779 ew32(TXDCTL(0), reg_data); 780 781 /* ...for both queues. */ 782 reg_data = er32(TXDCTL(1)); 783 reg_data = ((reg_data & ~E1000_TXDCTL_WTHRESH) | 784 E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC); 785 ew32(TXDCTL(1), reg_data); 786 787 /* Enable retransmit on late collisions */ 788 reg_data = er32(TCTL); 789 reg_data |= E1000_TCTL_RTLC; 790 ew32(TCTL, reg_data); 791 792 /* Configure Gigabit Carry Extend Padding */ 793 reg_data = er32(TCTL_EXT); 794 reg_data &= ~E1000_TCTL_EXT_GCEX_MASK; 795 reg_data |= DEFAULT_TCTL_EXT_GCEX_80003ES2LAN; 796 ew32(TCTL_EXT, reg_data); 797 798 /* Configure Transmit Inter-Packet Gap */ 799 reg_data = er32(TIPG); 800 reg_data &= ~E1000_TIPG_IPGT_MASK; 801 reg_data |= DEFAULT_TIPG_IPGT_1000_80003ES2LAN; 802 ew32(TIPG, reg_data); 803 804 reg_data = E1000_READ_REG_ARRAY(hw, E1000_FFLT, 0x0001); 805 reg_data &= ~0x00100000; 806 E1000_WRITE_REG_ARRAY(hw, E1000_FFLT, 0x0001, reg_data); 807 808 /* default to true to enable the MDIC W/A */ 809 hw->dev_spec.e80003es2lan.mdic_wa_enable = true; 810 811 ret_val = 812 e1000_read_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_OFFSET >> 813 E1000_KMRNCTRLSTA_OFFSET_SHIFT, &i); 814 if (!ret_val) { 815 if ((i & E1000_KMRNCTRLSTA_OPMODE_MASK) == 816 E1000_KMRNCTRLSTA_OPMODE_INBAND_MDIO) 817 hw->dev_spec.e80003es2lan.mdic_wa_enable = false; 818 } 819 820 /* Clear all of the statistics registers (clear on read). It is 821 * important that we do this after we have tried to establish link 822 * because the symbol error count will increment wildly if there 823 * is no link. 824 */ 825 e1000_clear_hw_cntrs_80003es2lan(hw); 826 827 return ret_val; 828 } 829 830 /** 831 * e1000_initialize_hw_bits_80003es2lan - Init hw bits of ESB2 832 * @hw: pointer to the HW structure 833 * 834 * Initializes required hardware-dependent bits needed for normal operation. 835 **/ 836 static void e1000_initialize_hw_bits_80003es2lan(struct e1000_hw *hw) 837 { 838 u32 reg; 839 840 /* Transmit Descriptor Control 0 */ 841 reg = er32(TXDCTL(0)); 842 reg |= BIT(22); 843 ew32(TXDCTL(0), reg); 844 845 /* Transmit Descriptor Control 1 */ 846 reg = er32(TXDCTL(1)); 847 reg |= BIT(22); 848 ew32(TXDCTL(1), reg); 849 850 /* Transmit Arbitration Control 0 */ 851 reg = er32(TARC(0)); 852 reg &= ~(0xF << 27); /* 30:27 */ 853 if (hw->phy.media_type != e1000_media_type_copper) 854 reg &= ~BIT(20); 855 ew32(TARC(0), reg); 856 857 /* Transmit Arbitration Control 1 */ 858 reg = er32(TARC(1)); 859 if (er32(TCTL) & E1000_TCTL_MULR) 860 reg &= ~BIT(28); 861 else 862 reg |= BIT(28); 863 ew32(TARC(1), reg); 864 865 /* Disable IPv6 extension header parsing because some malformed 866 * IPv6 headers can hang the Rx. 867 */ 868 reg = er32(RFCTL); 869 reg |= (E1000_RFCTL_IPV6_EX_DIS | E1000_RFCTL_NEW_IPV6_EXT_DIS); 870 ew32(RFCTL, reg); 871 } 872 873 /** 874 * e1000_copper_link_setup_gg82563_80003es2lan - Configure GG82563 Link 875 * @hw: pointer to the HW structure 876 * 877 * Setup some GG82563 PHY registers for obtaining link 878 **/ 879 static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw) 880 { 881 struct e1000_phy_info *phy = &hw->phy; 882 s32 ret_val; 883 u32 reg; 884 u16 data; 885 886 ret_val = e1e_rphy(hw, GG82563_PHY_MAC_SPEC_CTRL, &data); 887 if (ret_val) 888 return ret_val; 889 890 data |= GG82563_MSCR_ASSERT_CRS_ON_TX; 891 /* Use 25MHz for both link down and 1000Base-T for Tx clock. */ 892 data |= GG82563_MSCR_TX_CLK_1000MBPS_25; 893 894 ret_val = e1e_wphy(hw, GG82563_PHY_MAC_SPEC_CTRL, data); 895 if (ret_val) 896 return ret_val; 897 898 /* Options: 899 * MDI/MDI-X = 0 (default) 900 * 0 - Auto for all speeds 901 * 1 - MDI mode 902 * 2 - MDI-X mode 903 * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes) 904 */ 905 ret_val = e1e_rphy(hw, GG82563_PHY_SPEC_CTRL, &data); 906 if (ret_val) 907 return ret_val; 908 909 data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK; 910 911 switch (phy->mdix) { 912 case 1: 913 data |= GG82563_PSCR_CROSSOVER_MODE_MDI; 914 break; 915 case 2: 916 data |= GG82563_PSCR_CROSSOVER_MODE_MDIX; 917 break; 918 case 0: 919 default: 920 data |= GG82563_PSCR_CROSSOVER_MODE_AUTO; 921 break; 922 } 923 924 /* Options: 925 * disable_polarity_correction = 0 (default) 926 * Automatic Correction for Reversed Cable Polarity 927 * 0 - Disabled 928 * 1 - Enabled 929 */ 930 data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE; 931 if (phy->disable_polarity_correction) 932 data |= GG82563_PSCR_POLARITY_REVERSAL_DISABLE; 933 934 ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL, data); 935 if (ret_val) 936 return ret_val; 937 938 /* SW Reset the PHY so all changes take effect */ 939 ret_val = hw->phy.ops.commit(hw); 940 if (ret_val) { 941 e_dbg("Error Resetting the PHY\n"); 942 return ret_val; 943 } 944 945 /* Bypass Rx and Tx FIFO's */ 946 reg = E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL; 947 data = (E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS | 948 E1000_KMRNCTRLSTA_FIFO_CTRL_TX_BYPASS); 949 ret_val = e1000_write_kmrn_reg_80003es2lan(hw, reg, data); 950 if (ret_val) 951 return ret_val; 952 953 reg = E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE; 954 ret_val = e1000_read_kmrn_reg_80003es2lan(hw, reg, &data); 955 if (ret_val) 956 return ret_val; 957 data |= E1000_KMRNCTRLSTA_OPMODE_E_IDLE; 958 ret_val = e1000_write_kmrn_reg_80003es2lan(hw, reg, data); 959 if (ret_val) 960 return ret_val; 961 962 ret_val = e1e_rphy(hw, GG82563_PHY_SPEC_CTRL_2, &data); 963 if (ret_val) 964 return ret_val; 965 966 data &= ~GG82563_PSCR2_REVERSE_AUTO_NEG; 967 ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL_2, data); 968 if (ret_val) 969 return ret_val; 970 971 reg = er32(CTRL_EXT); 972 reg &= ~E1000_CTRL_EXT_LINK_MODE_MASK; 973 ew32(CTRL_EXT, reg); 974 975 ret_val = e1e_rphy(hw, GG82563_PHY_PWR_MGMT_CTRL, &data); 976 if (ret_val) 977 return ret_val; 978 979 /* Do not init these registers when the HW is in IAMT mode, since the 980 * firmware will have already initialized them. We only initialize 981 * them if the HW is not in IAMT mode. 982 */ 983 if (!hw->mac.ops.check_mng_mode(hw)) { 984 /* Enable Electrical Idle on the PHY */ 985 data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE; 986 ret_val = e1e_wphy(hw, GG82563_PHY_PWR_MGMT_CTRL, data); 987 if (ret_val) 988 return ret_val; 989 990 ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &data); 991 if (ret_val) 992 return ret_val; 993 994 data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; 995 ret_val = e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, data); 996 if (ret_val) 997 return ret_val; 998 } 999 1000 /* Workaround: Disable padding in Kumeran interface in the MAC 1001 * and in the PHY to avoid CRC errors. 1002 */ 1003 ret_val = e1e_rphy(hw, GG82563_PHY_INBAND_CTRL, &data); 1004 if (ret_val) 1005 return ret_val; 1006 1007 data |= GG82563_ICR_DIS_PADDING; 1008 ret_val = e1e_wphy(hw, GG82563_PHY_INBAND_CTRL, data); 1009 if (ret_val) 1010 return ret_val; 1011 1012 return 0; 1013 } 1014 1015 /** 1016 * e1000_setup_copper_link_80003es2lan - Setup Copper Link for ESB2 1017 * @hw: pointer to the HW structure 1018 * 1019 * Essentially a wrapper for setting up all things "copper" related. 1020 * This is a function pointer entry point called by the mac module. 1021 **/ 1022 static s32 e1000_setup_copper_link_80003es2lan(struct e1000_hw *hw) 1023 { 1024 u32 ctrl; 1025 s32 ret_val; 1026 u16 reg_data; 1027 1028 ctrl = er32(CTRL); 1029 ctrl |= E1000_CTRL_SLU; 1030 ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); 1031 ew32(CTRL, ctrl); 1032 1033 /* Set the mac to wait the maximum time between each 1034 * iteration and increase the max iterations when 1035 * polling the phy; this fixes erroneous timeouts at 10Mbps. 1036 */ 1037 ret_val = e1000_write_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 4), 1038 0xFFFF); 1039 if (ret_val) 1040 return ret_val; 1041 ret_val = e1000_read_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 9), 1042 ®_data); 1043 if (ret_val) 1044 return ret_val; 1045 reg_data |= 0x3F; 1046 ret_val = e1000_write_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 9), 1047 reg_data); 1048 if (ret_val) 1049 return ret_val; 1050 ret_val = 1051 e1000_read_kmrn_reg_80003es2lan(hw, 1052 E1000_KMRNCTRLSTA_OFFSET_INB_CTRL, 1053 ®_data); 1054 if (ret_val) 1055 return ret_val; 1056 reg_data |= E1000_KMRNCTRLSTA_INB_CTRL_DIS_PADDING; 1057 ret_val = 1058 e1000_write_kmrn_reg_80003es2lan(hw, 1059 E1000_KMRNCTRLSTA_OFFSET_INB_CTRL, 1060 reg_data); 1061 if (ret_val) 1062 return ret_val; 1063 1064 ret_val = e1000_copper_link_setup_gg82563_80003es2lan(hw); 1065 if (ret_val) 1066 return ret_val; 1067 1068 return e1000e_setup_copper_link(hw); 1069 } 1070 1071 /** 1072 * e1000_cfg_on_link_up_80003es2lan - es2 link configuration after link-up 1073 * @hw: pointer to the HW structure 1074 * 1075 * Configure the KMRN interface by applying last minute quirks for 1076 * 10/100 operation. 1077 **/ 1078 static s32 e1000_cfg_on_link_up_80003es2lan(struct e1000_hw *hw) 1079 { 1080 s32 ret_val = 0; 1081 u16 speed; 1082 u16 duplex; 1083 1084 if (hw->phy.media_type == e1000_media_type_copper) { 1085 ret_val = e1000e_get_speed_and_duplex_copper(hw, &speed, 1086 &duplex); 1087 if (ret_val) 1088 return ret_val; 1089 1090 if (speed == SPEED_1000) 1091 ret_val = e1000_cfg_kmrn_1000_80003es2lan(hw); 1092 else 1093 ret_val = e1000_cfg_kmrn_10_100_80003es2lan(hw, duplex); 1094 } 1095 1096 return ret_val; 1097 } 1098 1099 /** 1100 * e1000_cfg_kmrn_10_100_80003es2lan - Apply "quirks" for 10/100 operation 1101 * @hw: pointer to the HW structure 1102 * @duplex: current duplex setting 1103 * 1104 * Configure the KMRN interface by applying last minute quirks for 1105 * 10/100 operation. 1106 **/ 1107 static s32 e1000_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex) 1108 { 1109 s32 ret_val; 1110 u32 tipg; 1111 u32 i = 0; 1112 u16 reg_data, reg_data2; 1113 1114 reg_data = E1000_KMRNCTRLSTA_HD_CTRL_10_100_DEFAULT; 1115 ret_val = 1116 e1000_write_kmrn_reg_80003es2lan(hw, 1117 E1000_KMRNCTRLSTA_OFFSET_HD_CTRL, 1118 reg_data); 1119 if (ret_val) 1120 return ret_val; 1121 1122 /* Configure Transmit Inter-Packet Gap */ 1123 tipg = er32(TIPG); 1124 tipg &= ~E1000_TIPG_IPGT_MASK; 1125 tipg |= DEFAULT_TIPG_IPGT_10_100_80003ES2LAN; 1126 ew32(TIPG, tipg); 1127 1128 do { 1129 ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data); 1130 if (ret_val) 1131 return ret_val; 1132 1133 ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data2); 1134 if (ret_val) 1135 return ret_val; 1136 i++; 1137 } while ((reg_data != reg_data2) && (i < GG82563_MAX_KMRN_RETRY)); 1138 1139 if (duplex == HALF_DUPLEX) 1140 reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER; 1141 else 1142 reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; 1143 1144 return e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data); 1145 } 1146 1147 /** 1148 * e1000_cfg_kmrn_1000_80003es2lan - Apply "quirks" for gigabit operation 1149 * @hw: pointer to the HW structure 1150 * 1151 * Configure the KMRN interface by applying last minute quirks for 1152 * gigabit operation. 1153 **/ 1154 static s32 e1000_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw) 1155 { 1156 s32 ret_val; 1157 u16 reg_data, reg_data2; 1158 u32 tipg; 1159 u32 i = 0; 1160 1161 reg_data = E1000_KMRNCTRLSTA_HD_CTRL_1000_DEFAULT; 1162 ret_val = 1163 e1000_write_kmrn_reg_80003es2lan(hw, 1164 E1000_KMRNCTRLSTA_OFFSET_HD_CTRL, 1165 reg_data); 1166 if (ret_val) 1167 return ret_val; 1168 1169 /* Configure Transmit Inter-Packet Gap */ 1170 tipg = er32(TIPG); 1171 tipg &= ~E1000_TIPG_IPGT_MASK; 1172 tipg |= DEFAULT_TIPG_IPGT_1000_80003ES2LAN; 1173 ew32(TIPG, tipg); 1174 1175 do { 1176 ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data); 1177 if (ret_val) 1178 return ret_val; 1179 1180 ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data2); 1181 if (ret_val) 1182 return ret_val; 1183 i++; 1184 } while ((reg_data != reg_data2) && (i < GG82563_MAX_KMRN_RETRY)); 1185 1186 reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; 1187 1188 return e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data); 1189 } 1190 1191 /** 1192 * e1000_read_kmrn_reg_80003es2lan - Read kumeran register 1193 * @hw: pointer to the HW structure 1194 * @offset: register offset to be read 1195 * @data: pointer to the read data 1196 * 1197 * Acquire semaphore, then read the PHY register at offset 1198 * using the kumeran interface. The information retrieved is stored in data. 1199 * Release the semaphore before exiting. 1200 **/ 1201 static s32 e1000_read_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset, 1202 u16 *data) 1203 { 1204 u32 kmrnctrlsta; 1205 s32 ret_val; 1206 1207 ret_val = e1000_acquire_mac_csr_80003es2lan(hw); 1208 if (ret_val) 1209 return ret_val; 1210 1211 kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) & 1212 E1000_KMRNCTRLSTA_OFFSET) | E1000_KMRNCTRLSTA_REN; 1213 ew32(KMRNCTRLSTA, kmrnctrlsta); 1214 e1e_flush(); 1215 1216 udelay(2); 1217 1218 kmrnctrlsta = er32(KMRNCTRLSTA); 1219 *data = (u16)kmrnctrlsta; 1220 1221 e1000_release_mac_csr_80003es2lan(hw); 1222 1223 return ret_val; 1224 } 1225 1226 /** 1227 * e1000_write_kmrn_reg_80003es2lan - Write kumeran register 1228 * @hw: pointer to the HW structure 1229 * @offset: register offset to write to 1230 * @data: data to write at register offset 1231 * 1232 * Acquire semaphore, then write the data to PHY register 1233 * at the offset using the kumeran interface. Release semaphore 1234 * before exiting. 1235 **/ 1236 static s32 e1000_write_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset, 1237 u16 data) 1238 { 1239 u32 kmrnctrlsta; 1240 s32 ret_val; 1241 1242 ret_val = e1000_acquire_mac_csr_80003es2lan(hw); 1243 if (ret_val) 1244 return ret_val; 1245 1246 kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) & 1247 E1000_KMRNCTRLSTA_OFFSET) | data; 1248 ew32(KMRNCTRLSTA, kmrnctrlsta); 1249 e1e_flush(); 1250 1251 udelay(2); 1252 1253 e1000_release_mac_csr_80003es2lan(hw); 1254 1255 return ret_val; 1256 } 1257 1258 /** 1259 * e1000_read_mac_addr_80003es2lan - Read device MAC address 1260 * @hw: pointer to the HW structure 1261 **/ 1262 static s32 e1000_read_mac_addr_80003es2lan(struct e1000_hw *hw) 1263 { 1264 s32 ret_val; 1265 1266 /* If there's an alternate MAC address place it in RAR0 1267 * so that it will override the Si installed default perm 1268 * address. 1269 */ 1270 ret_val = e1000_check_alt_mac_addr_generic(hw); 1271 if (ret_val) 1272 return ret_val; 1273 1274 return e1000_read_mac_addr_generic(hw); 1275 } 1276 1277 /** 1278 * e1000_power_down_phy_copper_80003es2lan - Remove link during PHY power down 1279 * @hw: pointer to the HW structure 1280 * 1281 * In the case of a PHY power down to save power, or to turn off link during a 1282 * driver unload, or wake on lan is not enabled, remove the link. 1283 **/ 1284 static void e1000_power_down_phy_copper_80003es2lan(struct e1000_hw *hw) 1285 { 1286 /* If the management interface is not enabled, then power down */ 1287 if (!(hw->mac.ops.check_mng_mode(hw) || 1288 hw->phy.ops.check_reset_block(hw))) 1289 e1000_power_down_phy_copper(hw); 1290 } 1291 1292 /** 1293 * e1000_clear_hw_cntrs_80003es2lan - Clear device specific hardware counters 1294 * @hw: pointer to the HW structure 1295 * 1296 * Clears the hardware counters by reading the counter registers. 1297 **/ 1298 static void e1000_clear_hw_cntrs_80003es2lan(struct e1000_hw *hw) 1299 { 1300 e1000e_clear_hw_cntrs_base(hw); 1301 1302 er32(PRC64); 1303 er32(PRC127); 1304 er32(PRC255); 1305 er32(PRC511); 1306 er32(PRC1023); 1307 er32(PRC1522); 1308 er32(PTC64); 1309 er32(PTC127); 1310 er32(PTC255); 1311 er32(PTC511); 1312 er32(PTC1023); 1313 er32(PTC1522); 1314 1315 er32(ALGNERRC); 1316 er32(RXERRC); 1317 er32(TNCRS); 1318 er32(CEXTERR); 1319 er32(TSCTC); 1320 er32(TSCTFC); 1321 1322 er32(MGTPRC); 1323 er32(MGTPDC); 1324 er32(MGTPTC); 1325 1326 er32(IAC); 1327 er32(ICRXOC); 1328 1329 er32(ICRXPTC); 1330 er32(ICRXATC); 1331 er32(ICTXPTC); 1332 er32(ICTXATC); 1333 er32(ICTXQEC); 1334 er32(ICTXQMTC); 1335 er32(ICRXDMTC); 1336 } 1337 1338 static const struct e1000_mac_operations es2_mac_ops = { 1339 .read_mac_addr = e1000_read_mac_addr_80003es2lan, 1340 .id_led_init = e1000e_id_led_init_generic, 1341 .blink_led = e1000e_blink_led_generic, 1342 .check_mng_mode = e1000e_check_mng_mode_generic, 1343 /* check_for_link dependent on media type */ 1344 .cleanup_led = e1000e_cleanup_led_generic, 1345 .clear_hw_cntrs = e1000_clear_hw_cntrs_80003es2lan, 1346 .get_bus_info = e1000e_get_bus_info_pcie, 1347 .set_lan_id = e1000_set_lan_id_multi_port_pcie, 1348 .get_link_up_info = e1000_get_link_up_info_80003es2lan, 1349 .led_on = e1000e_led_on_generic, 1350 .led_off = e1000e_led_off_generic, 1351 .update_mc_addr_list = e1000e_update_mc_addr_list_generic, 1352 .write_vfta = e1000_write_vfta_generic, 1353 .clear_vfta = e1000_clear_vfta_generic, 1354 .reset_hw = e1000_reset_hw_80003es2lan, 1355 .init_hw = e1000_init_hw_80003es2lan, 1356 .setup_link = e1000e_setup_link_generic, 1357 /* setup_physical_interface dependent on media type */ 1358 .setup_led = e1000e_setup_led_generic, 1359 .config_collision_dist = e1000e_config_collision_dist_generic, 1360 .rar_set = e1000e_rar_set_generic, 1361 .rar_get_count = e1000e_rar_get_count_generic, 1362 }; 1363 1364 static const struct e1000_phy_operations es2_phy_ops = { 1365 .acquire = e1000_acquire_phy_80003es2lan, 1366 .check_polarity = e1000_check_polarity_m88, 1367 .check_reset_block = e1000e_check_reset_block_generic, 1368 .commit = e1000e_phy_sw_reset, 1369 .force_speed_duplex = e1000_phy_force_speed_duplex_80003es2lan, 1370 .get_cfg_done = e1000_get_cfg_done_80003es2lan, 1371 .get_cable_length = e1000_get_cable_length_80003es2lan, 1372 .get_info = e1000e_get_phy_info_m88, 1373 .read_reg = e1000_read_phy_reg_gg82563_80003es2lan, 1374 .release = e1000_release_phy_80003es2lan, 1375 .reset = e1000e_phy_hw_reset_generic, 1376 .set_d0_lplu_state = NULL, 1377 .set_d3_lplu_state = e1000e_set_d3_lplu_state, 1378 .write_reg = e1000_write_phy_reg_gg82563_80003es2lan, 1379 .cfg_on_link_up = e1000_cfg_on_link_up_80003es2lan, 1380 }; 1381 1382 static const struct e1000_nvm_operations es2_nvm_ops = { 1383 .acquire = e1000_acquire_nvm_80003es2lan, 1384 .read = e1000e_read_nvm_eerd, 1385 .release = e1000_release_nvm_80003es2lan, 1386 .reload = e1000e_reload_nvm_generic, 1387 .update = e1000e_update_nvm_checksum_generic, 1388 .valid_led_default = e1000e_valid_led_default, 1389 .validate = e1000e_validate_nvm_checksum_generic, 1390 .write = e1000_write_nvm_80003es2lan, 1391 }; 1392 1393 const struct e1000_info e1000_es2_info = { 1394 .mac = e1000_80003es2lan, 1395 .flags = FLAG_HAS_HW_VLAN_FILTER 1396 | FLAG_HAS_JUMBO_FRAMES 1397 | FLAG_HAS_WOL 1398 | FLAG_APME_IN_CTRL3 1399 | FLAG_HAS_CTRLEXT_ON_LOAD 1400 | FLAG_RX_NEEDS_RESTART /* errata */ 1401 | FLAG_TARC_SET_BIT_ZERO /* errata */ 1402 | FLAG_APME_CHECK_PORT_B 1403 | FLAG_DISABLE_FC_PAUSE_TIME, /* errata */ 1404 .flags2 = FLAG2_DMA_BURST, 1405 .pba = 38, 1406 .max_hw_frame_size = DEFAULT_JUMBO, 1407 .get_variants = e1000_get_variants_80003es2lan, 1408 .mac_ops = &es2_mac_ops, 1409 .phy_ops = &es2_phy_ops, 1410 .nvm_ops = &es2_nvm_ops, 1411 }; 1412