1#
2# HISILICON device configuration
3#
4
5config NET_VENDOR_HISILICON
6	bool "Hisilicon devices"
7	default y
8	depends on (OF || ACPI) && HAS_DMA
9	depends on ARM || ARM64 || COMPILE_TEST
10	---help---
11	  If you have a network (Ethernet) card belonging to this class, say Y.
12
13	  Note that the answer to this question doesn't directly affect the
14	  kernel: saying N will just cause the configurator to skip all
15	  the questions about Hisilicon devices. If you say Y, you will be asked
16	  for your specific card in the following questions.
17
18if NET_VENDOR_HISILICON
19
20config HIX5HD2_GMAC
21	tristate "Hisilicon HIX5HD2 Family Network Device Support"
22	select PHYLIB
23	help
24	  This selects the hix5hd2 mac family network device.
25
26config HISI_FEMAC
27	tristate "Hisilicon Fast Ethernet MAC device support"
28	depends on HAS_IOMEM
29	select PHYLIB
30	select RESET_CONTROLLER
31	help
32	  This selects the Hisilicon Fast Ethernet MAC device(FEMAC).
33	  The FEMAC receives and transmits data over Ethernet
34	  ports at 10/100 Mbps in full-duplex or half-duplex mode.
35	  The FEMAC exchanges data with the CPU, and supports
36	  the energy efficient Ethernet (EEE).
37
38config HIP04_ETH
39	tristate "HISILICON P04 Ethernet support"
40	depends on HAS_IOMEM	# For MFD_SYSCON
41	select MARVELL_PHY
42	select MFD_SYSCON
43	select HNS_MDIO
44	---help---
45	  If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
46	  want to use the internal ethernet then you should answer Y to this.
47
48config HNS_MDIO
49	tristate
50	select PHYLIB
51	---help---
52	  This selects the HNS MDIO support. It is needed by HNS_DSAF to access
53	  the PHY
54
55config HNS
56	tristate "Hisilicon Network Subsystem Support (Framework)"
57	---help---
58	  This selects the framework support for Hisilicon Network Subsystem. It
59	  is needed by any driver which provides HNS acceleration engine or make
60	  use of the engine
61
62config HNS_DSAF
63	tristate "Hisilicon HNS DSAF device Support"
64	select HNS
65	select HNS_MDIO
66	---help---
67	  This selects the DSAF (Distributed System Area Frabric) network
68	  acceleration engine support. The engine is used in Hisilicon hip05,
69	  Hi1610 and further ICT SoC
70
71config HNS_ENET
72	tristate "Hisilicon HNS Ethernet Device Support"
73	select PHYLIB
74	select HNS
75	---help---
76	  This selects the general ethernet driver for HNS.  This module make
77	  use of any HNS AE driver, such as HNS_DSAF
78
79config HNS3
80	tristate "Hisilicon Network Subsystem Support HNS3 (Framework)"
81	depends on PCI
82	---help---
83	  This selects the framework support for Hisilicon Network Subsystem 3.
84	  This layer facilitates clients like ENET, RoCE and user-space ethernet
85	  drivers(like ODP)to register with HNAE devices and their associated
86	  operations.
87
88config HNS3_HCLGE
89	tristate "Hisilicon HNS3 HCLGE Acceleration Engine & Compatibility Layer Support"
90	depends on PCI_MSI
91	depends on HNS3
92	---help---
93	  This selects the HNS3_HCLGE network acceleration engine & its hardware
94	  compatibility layer. The engine would be used in Hisilicon hip08 family of
95	  SoCs and further upcoming SoCs.
96
97config HNS3_ENET
98	tristate "Hisilicon HNS3 Ethernet Device Support"
99	depends on 64BIT && PCI
100	depends on HNS3 && HNS3_HCLGE
101	---help---
102	  This selects the Ethernet Driver for Hisilicon Network Subsystem 3 for hip08
103	  family of SoCs. This module depends upon HNAE3 driver to access the HNAE3
104	  devices and their associated operations.
105
106config HNS3_DCB
107	bool "Hisilicon HNS3 Data Center Bridge Support"
108	default n
109	depends on HNS3 && HNS3_HCLGE && DCB
110	---help---
111	  Say Y here if you want to use Data Center Bridging (DCB) in the HNS3 driver.
112
113	  If unsure, say N.
114
115endif # NET_VENDOR_HISILICON
116