1# SPDX-License-Identifier: GPL-2.0-only
2#
3# Freescale device configuration
4#
5
6config NET_VENDOR_FREESCALE
7	bool "Freescale devices"
8	default y
9	depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
10		   M523x || M527x || M5272 || M528x || M520x || M532x || \
11		   ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM) || \
12		   ARCH_LAYERSCAPE || ARCH_S32 || COMPILE_TEST
13	help
14	  If you have a network (Ethernet) card belonging to this class, say Y.
15
16	  Note that the answer to this question doesn't directly affect the
17	  kernel: saying N will just cause the configurator to skip all
18	  the questions about Freescale devices. If you say Y, you will be
19	  asked for your specific card in the following questions.
20
21if NET_VENDOR_FREESCALE
22
23config FEC
24	tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
25	depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
26		   ARCH_MXC || ARCH_S32 || SOC_IMX28 || COMPILE_TEST)
27	default ARCH_MXC || SOC_IMX28 if ARM
28	depends on PTP_1588_CLOCK_OPTIONAL
29	select CRC32
30	select PHYLIB
31	select PAGE_POOL
32	select PAGE_POOL_STATS
33	imply NET_SELFTESTS
34	help
35	  Say Y here if you want to use the built-in 10/100 Fast ethernet
36	  controller on some Motorola ColdFire and Freescale i.MX/S32 processors.
37
38config FEC_MPC52xx
39	tristate "FEC MPC52xx driver"
40	depends on PPC_MPC52xx && PPC_BESTCOMM
41	select CRC32
42	select PHYLIB
43	select PPC_BESTCOMM_FEC
44	help
45	  This option enables support for the MPC5200's on-chip
46	  Fast Ethernet Controller
47	  If compiled as module, it will be called fec_mpc52xx.
48
49config FEC_MPC52xx_MDIO
50	bool "FEC MPC52xx MDIO bus driver"
51	depends on FEC_MPC52xx
52	default y
53	help
54	  The MPC5200's FEC can connect to the Ethernet either with
55	  an external MII PHY chip or 10 Mbps 7-wire interface
56	  (Motorola? industry standard).
57	  If your board uses an external PHY connected to FEC, enable this.
58	  If not sure, enable.
59	  If compiled as module, it will be called fec_mpc52xx_phy.
60
61source "drivers/net/ethernet/freescale/fs_enet/Kconfig"
62source "drivers/net/ethernet/freescale/fman/Kconfig"
63
64config FSL_PQ_MDIO
65	tristate "Freescale PQ MDIO"
66	select PHYLIB
67	help
68	  This driver supports the MDIO bus used by the gianfar and UCC drivers.
69
70config FSL_XGMAC_MDIO
71	tristate "Freescale XGMAC MDIO"
72	select PHYLIB
73	depends on OF
74	select MDIO_DEVRES
75	select OF_MDIO
76	help
77	  This driver supports the MDIO bus on the Fman 10G Ethernet MACs, and
78	  on the FMan mEMAC (which supports both Clauses 22 and 45)
79
80config UCC_GETH
81	tristate "Freescale QE Gigabit Ethernet"
82	depends on QUICC_ENGINE && PPC32
83	select FSL_PQ_MDIO
84	select PHYLIB
85	select FIXED_PHY
86	help
87	  This driver supports the Gigabit Ethernet mode of the QUICC Engine,
88	  which is available on some Freescale SOCs.
89
90config UGETH_TX_ON_DEMAND
91	bool "Transmit on Demand support"
92	depends on UCC_GETH
93
94config GIANFAR
95	tristate "Gianfar Ethernet"
96	depends on HAS_DMA
97	select FSL_PQ_MDIO
98	select PHYLIB
99	select FIXED_PHY
100	select CRC32
101	help
102	  This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
103	  and MPC86xx family of chips, the eTSEC on LS1021A and the FEC
104	  on the 8540.
105
106source "drivers/net/ethernet/freescale/dpaa/Kconfig"
107source "drivers/net/ethernet/freescale/dpaa2/Kconfig"
108source "drivers/net/ethernet/freescale/enetc/Kconfig"
109
110endif # NET_VENDOR_FREESCALE
111