1#
2# Freescale device configuration
3#
4
5config NET_VENDOR_FREESCALE
6	bool "Freescale devices"
7	default y
8	depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
9		   M523x || M527x || M5272 || M528x || M520x || M532x || \
10		   ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM)
11	---help---
12	  If you have a network (Ethernet) card belonging to this class, say Y.
13
14	  Note that the answer to this question doesn't directly affect the
15	  kernel: saying N will just cause the configurator to skip all
16	  the questions about Freescale devices. If you say Y, you will be
17	  asked for your specific card in the following questions.
18
19if NET_VENDOR_FREESCALE
20
21config FEC
22	tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
23	depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
24		   ARCH_MXC || SOC_IMX28)
25	default ARCH_MXC || SOC_IMX28 if ARM
26	select PHYLIB
27	select PTP_1588_CLOCK
28	---help---
29	  Say Y here if you want to use the built-in 10/100 Fast ethernet
30	  controller on some Motorola ColdFire and Freescale i.MX processors.
31
32config FEC_MPC52xx
33	tristate "FEC MPC52xx driver"
34	depends on PPC_MPC52xx && PPC_BESTCOMM
35	select CRC32
36	select PHYLIB
37	select PPC_BESTCOMM_FEC
38	---help---
39	  This option enables support for the MPC5200's on-chip
40	  Fast Ethernet Controller
41	  If compiled as module, it will be called fec_mpc52xx.
42
43config FEC_MPC52xx_MDIO
44	bool "FEC MPC52xx MDIO bus driver"
45	depends on FEC_MPC52xx
46	default y
47	---help---
48	  The MPC5200's FEC can connect to the Ethernet either with
49	  an external MII PHY chip or 10 Mbps 7-wire interface
50	  (Motorola? industry standard).
51	  If your board uses an external PHY connected to FEC, enable this.
52	  If not sure, enable.
53	  If compiled as module, it will be called fec_mpc52xx_phy.
54
55source "drivers/net/ethernet/freescale/fs_enet/Kconfig"
56
57config FSL_PQ_MDIO
58	tristate "Freescale PQ MDIO"
59	select PHYLIB
60	---help---
61	  This driver supports the MDIO bus used by the gianfar and UCC drivers.
62
63config FSL_XGMAC_MDIO
64	tristate "Freescale XGMAC MDIO"
65	select PHYLIB
66	select OF_MDIO
67	---help---
68	  This driver supports the MDIO bus on the Fman 10G Ethernet MACs, and
69	  on the FMan mEMAC (which supports both Clauses 22 and 45)
70
71config UCC_GETH
72	tristate "Freescale QE Gigabit Ethernet"
73	depends on QUICC_ENGINE
74	select FSL_PQ_MDIO
75	select PHYLIB
76	---help---
77	  This driver supports the Gigabit Ethernet mode of the QUICC Engine,
78	  which is available on some Freescale SOCs.
79
80config UGETH_TX_ON_DEMAND
81	bool "Transmit on Demand support"
82	depends on UCC_GETH
83
84config GIANFAR
85	tristate "Gianfar Ethernet"
86	select FSL_PQ_MDIO
87	select PHYLIB
88	select CRC32
89	---help---
90	  This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
91	  and MPC86xx family of chips, the eTSEC on LS1021A and the FEC
92	  on the 8540.
93
94endif # NET_VENDOR_FREESCALE
95