1#
2# Freescale device configuration
3#
4
5config NET_VENDOR_FREESCALE
6	bool "Freescale devices"
7	default y
8	depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
9		   M523x || M527x || M5272 || M528x || M520x || M532x || \
10		   ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM)
11	---help---
12	  If you have a network (Ethernet) card belonging to this class, say Y
13	  and read the Ethernet-HOWTO, available from
14	  <http://www.tldp.org/docs.html#howto>.
15
16	  Note that the answer to this question doesn't directly affect the
17	  kernel: saying N will just cause the configurator to skip all
18	  the questions about Freescale devices. If you say Y, you will be
19	  asked for your specific card in the following questions.
20
21if NET_VENDOR_FREESCALE
22
23config FEC
24	tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
25	depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
26		   ARCH_MXC || SOC_IMX28)
27	default ARCH_MXC || SOC_IMX28 if ARM
28	select PHYLIB
29	---help---
30	  Say Y here if you want to use the built-in 10/100 Fast ethernet
31	  controller on some Motorola ColdFire and Freescale i.MX processors.
32
33config FEC_MPC52xx
34	tristate "FEC MPC52xx driver"
35	depends on PPC_MPC52xx && PPC_BESTCOMM
36	select CRC32
37	select PHYLIB
38	select PPC_BESTCOMM_FEC
39	---help---
40	  This option enables support for the MPC5200's on-chip
41	  Fast Ethernet Controller
42	  If compiled as module, it will be called fec_mpc52xx.
43
44config FEC_MPC52xx_MDIO
45	bool "FEC MPC52xx MDIO bus driver"
46	depends on FEC_MPC52xx
47	default y
48	---help---
49	  The MPC5200's FEC can connect to the Ethernet either with
50	  an external MII PHY chip or 10 Mbps 7-wire interface
51	  (Motorola? industry standard).
52	  If your board uses an external PHY connected to FEC, enable this.
53	  If not sure, enable.
54	  If compiled as module, it will be called fec_mpc52xx_phy.
55
56source "drivers/net/ethernet/freescale/fs_enet/Kconfig"
57
58config FSL_PQ_MDIO
59	tristate "Freescale PQ MDIO"
60	depends on FSL_SOC
61	select PHYLIB
62	---help---
63	  This driver supports the MDIO bus used by the gianfar and UCC drivers.
64
65config UCC_GETH
66	tristate "Freescale QE Gigabit Ethernet"
67	depends on QUICC_ENGINE
68	select FSL_PQ_MDIO
69	select PHYLIB
70	---help---
71	  This driver supports the Gigabit Ethernet mode of the QUICC Engine,
72	  which is available on some Freescale SOCs.
73
74config UGETH_TX_ON_DEMAND
75	bool "Transmit on Demand support"
76	depends on UCC_GETH
77
78config GIANFAR
79	tristate "Gianfar Ethernet"
80	depends on FSL_SOC
81	select FSL_PQ_MDIO
82	select PHYLIB
83	select CRC32
84	---help---
85	  This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
86	  and MPC86xx family of chips, and the FEC on the 8540.
87
88endif # NET_VENDOR_FREESCALE
89