1# SPDX-License-Identifier: GPL-2.0-only
2#
3# Freescale device configuration
4#
5
6config NET_VENDOR_FREESCALE
7	bool "Freescale devices"
8	default y
9	depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
10		   M523x || M527x || M5272 || M528x || M520x || M532x || \
11		   ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM) || \
12		   ARCH_LAYERSCAPE || COMPILE_TEST
13	help
14	  If you have a network (Ethernet) card belonging to this class, say Y.
15
16	  Note that the answer to this question doesn't directly affect the
17	  kernel: saying N will just cause the configurator to skip all
18	  the questions about Freescale devices. If you say Y, you will be
19	  asked for your specific card in the following questions.
20
21if NET_VENDOR_FREESCALE
22
23config FEC
24	tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
25	depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
26		   ARCH_MXC || SOC_IMX28 || COMPILE_TEST)
27	default ARCH_MXC || SOC_IMX28 if ARM
28	select CRC32
29	select PHYLIB
30	imply PTP_1588_CLOCK
31	help
32	  Say Y here if you want to use the built-in 10/100 Fast ethernet
33	  controller on some Motorola ColdFire and Freescale i.MX processors.
34
35config FEC_MPC52xx
36	tristate "FEC MPC52xx driver"
37	depends on PPC_MPC52xx && PPC_BESTCOMM
38	select CRC32
39	select PHYLIB
40	select PPC_BESTCOMM_FEC
41	help
42	  This option enables support for the MPC5200's on-chip
43	  Fast Ethernet Controller
44	  If compiled as module, it will be called fec_mpc52xx.
45
46config FEC_MPC52xx_MDIO
47	bool "FEC MPC52xx MDIO bus driver"
48	depends on FEC_MPC52xx
49	default y
50	help
51	  The MPC5200's FEC can connect to the Ethernet either with
52	  an external MII PHY chip or 10 Mbps 7-wire interface
53	  (Motorola? industry standard).
54	  If your board uses an external PHY connected to FEC, enable this.
55	  If not sure, enable.
56	  If compiled as module, it will be called fec_mpc52xx_phy.
57
58source "drivers/net/ethernet/freescale/fs_enet/Kconfig"
59source "drivers/net/ethernet/freescale/fman/Kconfig"
60
61config FSL_PQ_MDIO
62	tristate "Freescale PQ MDIO"
63	select PHYLIB
64	help
65	  This driver supports the MDIO bus used by the gianfar and UCC drivers.
66
67config FSL_XGMAC_MDIO
68	tristate "Freescale XGMAC MDIO"
69	select PHYLIB
70	depends on OF
71	select OF_MDIO
72	help
73	  This driver supports the MDIO bus on the Fman 10G Ethernet MACs, and
74	  on the FMan mEMAC (which supports both Clauses 22 and 45)
75
76config UCC_GETH
77	tristate "Freescale QE Gigabit Ethernet"
78	depends on QUICC_ENGINE && PPC32
79	select FSL_PQ_MDIO
80	select PHYLIB
81	select FIXED_PHY
82	help
83	  This driver supports the Gigabit Ethernet mode of the QUICC Engine,
84	  which is available on some Freescale SOCs.
85
86config UGETH_TX_ON_DEMAND
87	bool "Transmit on Demand support"
88	depends on UCC_GETH
89
90config GIANFAR
91	tristate "Gianfar Ethernet"
92	depends on HAS_DMA
93	select FSL_PQ_MDIO
94	select PHYLIB
95	select FIXED_PHY
96	select CRC32
97	help
98	  This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
99	  and MPC86xx family of chips, the eTSEC on LS1021A and the FEC
100	  on the 8540.
101
102source "drivers/net/ethernet/freescale/dpaa/Kconfig"
103source "drivers/net/ethernet/freescale/dpaa2/Kconfig"
104source "drivers/net/ethernet/freescale/enetc/Kconfig"
105
106endif # NET_VENDOR_FREESCALE
107