1#
2# Freescale device configuration
3#
4
5config NET_VENDOR_FREESCALE
6	bool "Freescale devices"
7	default y
8	depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
9		   M523x || M527x || M5272 || M528x || M520x || M532x || \
10		   ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM) || \
11		   ARCH_LAYERSCAPE
12	---help---
13	  If you have a network (Ethernet) card belonging to this class, say Y.
14
15	  Note that the answer to this question doesn't directly affect the
16	  kernel: saying N will just cause the configurator to skip all
17	  the questions about Freescale devices. If you say Y, you will be
18	  asked for your specific card in the following questions.
19
20if NET_VENDOR_FREESCALE
21
22config FEC
23	tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
24	depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
25		   ARCH_MXC || SOC_IMX28)
26	default ARCH_MXC || SOC_IMX28 if ARM
27	select PHYLIB
28	select PTP_1588_CLOCK
29	---help---
30	  Say Y here if you want to use the built-in 10/100 Fast ethernet
31	  controller on some Motorola ColdFire and Freescale i.MX processors.
32
33config FEC_MPC52xx
34	tristate "FEC MPC52xx driver"
35	depends on PPC_MPC52xx && PPC_BESTCOMM
36	select CRC32
37	select PHYLIB
38	select PPC_BESTCOMM_FEC
39	---help---
40	  This option enables support for the MPC5200's on-chip
41	  Fast Ethernet Controller
42	  If compiled as module, it will be called fec_mpc52xx.
43
44config FEC_MPC52xx_MDIO
45	bool "FEC MPC52xx MDIO bus driver"
46	depends on FEC_MPC52xx
47	default y
48	---help---
49	  The MPC5200's FEC can connect to the Ethernet either with
50	  an external MII PHY chip or 10 Mbps 7-wire interface
51	  (Motorola? industry standard).
52	  If your board uses an external PHY connected to FEC, enable this.
53	  If not sure, enable.
54	  If compiled as module, it will be called fec_mpc52xx_phy.
55
56source "drivers/net/ethernet/freescale/fs_enet/Kconfig"
57source "drivers/net/ethernet/freescale/fman/Kconfig"
58
59config FSL_PQ_MDIO
60	tristate "Freescale PQ MDIO"
61	select PHYLIB
62	---help---
63	  This driver supports the MDIO bus used by the gianfar and UCC drivers.
64
65config FSL_XGMAC_MDIO
66	tristate "Freescale XGMAC MDIO"
67	select PHYLIB
68	select OF_MDIO
69	---help---
70	  This driver supports the MDIO bus on the Fman 10G Ethernet MACs, and
71	  on the FMan mEMAC (which supports both Clauses 22 and 45)
72
73config UCC_GETH
74	tristate "Freescale QE Gigabit Ethernet"
75	depends on QUICC_ENGINE
76	select FSL_PQ_MDIO
77	select PHYLIB
78	---help---
79	  This driver supports the Gigabit Ethernet mode of the QUICC Engine,
80	  which is available on some Freescale SOCs.
81
82config UGETH_TX_ON_DEMAND
83	bool "Transmit on Demand support"
84	depends on UCC_GETH
85
86config GIANFAR
87	tristate "Gianfar Ethernet"
88	select FSL_PQ_MDIO
89	select PHYLIB
90	select CRC32
91	---help---
92	  This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
93	  and MPC86xx family of chips, the eTSEC on LS1021A and the FEC
94	  on the 8540.
95
96endif # NET_VENDOR_FREESCALE
97