1# SPDX-License-Identifier: GPL-2.0-only
2#
3# Freescale device configuration
4#
5
6config NET_VENDOR_FREESCALE
7	bool "Freescale devices"
8	default y
9	depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
10		   M523x || M527x || M5272 || M528x || M520x || M532x || \
11		   ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM) || \
12		   ARCH_LAYERSCAPE || COMPILE_TEST
13	help
14	  If you have a network (Ethernet) card belonging to this class, say Y.
15
16	  Note that the answer to this question doesn't directly affect the
17	  kernel: saying N will just cause the configurator to skip all
18	  the questions about Freescale devices. If you say Y, you will be
19	  asked for your specific card in the following questions.
20
21if NET_VENDOR_FREESCALE
22
23config FEC
24	tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
25	depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
26		   ARCH_MXC || SOC_IMX28 || COMPILE_TEST)
27	default ARCH_MXC || SOC_IMX28 if ARM
28	select CRC32
29	select PHYLIB
30	imply NET_SELFTESTS
31	imply PTP_1588_CLOCK
32	help
33	  Say Y here if you want to use the built-in 10/100 Fast ethernet
34	  controller on some Motorola ColdFire and Freescale i.MX processors.
35
36config FEC_MPC52xx
37	tristate "FEC MPC52xx driver"
38	depends on PPC_MPC52xx && PPC_BESTCOMM
39	select CRC32
40	select PHYLIB
41	select PPC_BESTCOMM_FEC
42	help
43	  This option enables support for the MPC5200's on-chip
44	  Fast Ethernet Controller
45	  If compiled as module, it will be called fec_mpc52xx.
46
47config FEC_MPC52xx_MDIO
48	bool "FEC MPC52xx MDIO bus driver"
49	depends on FEC_MPC52xx
50	default y
51	help
52	  The MPC5200's FEC can connect to the Ethernet either with
53	  an external MII PHY chip or 10 Mbps 7-wire interface
54	  (Motorola? industry standard).
55	  If your board uses an external PHY connected to FEC, enable this.
56	  If not sure, enable.
57	  If compiled as module, it will be called fec_mpc52xx_phy.
58
59source "drivers/net/ethernet/freescale/fs_enet/Kconfig"
60source "drivers/net/ethernet/freescale/fman/Kconfig"
61
62config FSL_PQ_MDIO
63	tristate "Freescale PQ MDIO"
64	select PHYLIB
65	help
66	  This driver supports the MDIO bus used by the gianfar and UCC drivers.
67
68config FSL_XGMAC_MDIO
69	tristate "Freescale XGMAC MDIO"
70	select PHYLIB
71	depends on OF
72	select OF_MDIO
73	help
74	  This driver supports the MDIO bus on the Fman 10G Ethernet MACs, and
75	  on the FMan mEMAC (which supports both Clauses 22 and 45)
76
77config UCC_GETH
78	tristate "Freescale QE Gigabit Ethernet"
79	depends on QUICC_ENGINE && PPC32
80	select FSL_PQ_MDIO
81	select PHYLIB
82	select FIXED_PHY
83	help
84	  This driver supports the Gigabit Ethernet mode of the QUICC Engine,
85	  which is available on some Freescale SOCs.
86
87config UGETH_TX_ON_DEMAND
88	bool "Transmit on Demand support"
89	depends on UCC_GETH
90
91config GIANFAR
92	tristate "Gianfar Ethernet"
93	depends on HAS_DMA
94	select FSL_PQ_MDIO
95	select PHYLIB
96	select FIXED_PHY
97	select CRC32
98	help
99	  This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
100	  and MPC86xx family of chips, the eTSEC on LS1021A and the FEC
101	  on the 8540.
102
103source "drivers/net/ethernet/freescale/dpaa/Kconfig"
104source "drivers/net/ethernet/freescale/dpaa2/Kconfig"
105source "drivers/net/ethernet/freescale/enetc/Kconfig"
106
107endif # NET_VENDOR_FREESCALE
108